Ürünler (46.000+)

LM2202N - 230 MHz Video Amplifier System | Texas Instruments
LM2202N

LM2202N - 230 MHz Video Amplifier System | Texas Instruments

The Texas Instruments LM2202N is a 230 MHz video amplifier system intended for high-resolution monochrome and RGB color monitor applications, supplied in a 20-pin through-hole DIP package. It combines the video amplification functions needed in display signal paths within one integrated circuit and is identified by National Semiconductor as a general-purpose video amplifier system. A video amplifier system is an integrated circuit that conditions analog video signals so they can be reproduced reliably by a display or monitor. Its position in the signal chain is between the source of a composite or RGB video waveform and the display driver circuitry. The broad product category can be described as video amplifier, then analog video processing IC, then signal-conditioning integrated circuit, and finally semiconductor. The LM2202N is identified as a 230 MHz video amplifier system in a 20-PDIP package. Its key documented characteristics include video-amplifier functionality, a bandwidth designation of 230 MHz, general-purpose classification, through-hole construction, and a commercial-extended temperature grade. These attributes place it in applications requiring high-speed analog video amplification rather than low-frequency audio amplification or general-purpose logic. The LM2202N was developed for high-resolution monochrome and RGB color monitor systems. This application focus distinguishes it from general-purpose op-amp-based video circuits: the device is organized as a complete video amplifier system rather than as a general comparator or precision analog amplifier. At 230 MHz, it is suited to signal paths where wide video bandwidth is an important consideration. Typical uses include RGB monitor input stages, monochrome display channels, video test equipment, and legacy display electronics in which an analog video signal must be amplified before reaching the next processing stage. Component selection should account for the 20-pin DIP footprint, required bypass and termination components, and the signal amplitude expected at the amplifier input and output. Use the manufacturer pin-description table when assigning PCB connections, and follow the application circuit in the manufacturer datasheet for component values and signal termination. Because the part is a through-hole 20-pin DIP, board layout should preserve the package outline, pin numbering, and adequate clearance around adjacent traces. Confirm operating temperature and supply requirements against the datasheet before production use. This page organizes the LM2202N identity, package information, intended applications, sourcing guidance, and design cautions into one engineering reference. It also separates established device facts from parameters that require confirmation from the controlling manufacturer documentation, helping designers evaluate the IC without confusing it with unrelated video processors, monitors, or display-driver components.

RFQ İletişim
LM224AD - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM224AD

LM224AD - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM224AD is a standard general-purpose quad operational amplifier with four high-gain, frequency-compensated amplifiers in a 14-pin SOIC package. Its principal ratings include 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, 3 mV offset voltage, operation from ±1.5 V to ±16 V, and a 30 V maximum supply rating. The LM224A family is specified for -25°C to 85°C operation. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines its behavior. The LM224AD belongs to the general-purpose operational-amplifier family within analog ICs and amplifiers. Four independent amplifiers in one package provide a practical way to implement signal conditioning, buffering, voltage comparison, summing, or instrumentation functions when the required bandwidth and precision remain within the device's published ratings. Key characteristics include four amplifier circuits in one package, a 1.2 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. These figures make the device suitable for low-to-moderate-frequency analog signals rather than high-speed video or precision signal-chain applications. The 3 mV offset-voltage listing is particularly relevant when evaluating DC accuracy, while the wide ±1.5 V to ±16 V supply range supports both single-supply and split-supply arrangements. The LM224A device family uses high-gain, internally frequency-compensated amplifiers. Compensation avoids the need for an external dominant-pole capacitor in typical closed-loop uses, simplifying analog circuit design. Because all four channels share one package, designers can also reduce board area when four similar amplifier functions are required. Single and split supplies are relevant because the same amplifier can support grounded or bipolar signal systems, subject to the published common-mode and output-swing limits. Typical uses include four-channel sensor conditioning, low-frequency active filters, industrial control interfaces, general-purpose signal buffers, comparators with positive feedback, and analog summing networks. In each case, designers should verify noise, input bias current, common-mode range, output swing, stability, and load-driving capability against the manufacturer datasheet because those values are not present in the supplied source data. The primary design consideration is ensuring that signal bandwidth and amplitude remain compatible with the 1.2 MHz bandwidth and 0.5 V/µs slew rate. Place decoupling capacitors close to the supply pins, maintain a quiet ground reference, and route sensitive input signals away from high-current switching nodes. The complete 14-pin pin assignment and published limits should be checked in the manufacturer datasheet before layout release. This page combines the verified LM224A and LM224AD listings with distributor package information, same-package replacement candidates, and practical design guidance. It distinguishes documented ratings from parameters that still require direct confirmation from the official LM224 datasheet, avoiding unsupported assumptions about electrical performance, compliance, or stock status.

RFQ İletişim
LM224ADR - Quad 30V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM224ADR

LM224ADR - Quad 30V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM224ADR is a standard general-purpose quad operational amplifier with four high-gain, frequency-compensated amplifiers in a 14-pin SOIC package. Its principal ratings include 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, 3 mV offset voltage, operation from ±1.5 V to ±16 V, and a 30 V maximum supply rating. The LM224A family is specified for -25°C to 85°C operation. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines its behavior. The LM224ADR belongs to the general-purpose operational-amplifier family within analog ICs and amplifiers. Four independent amplifiers in one package provide a practical way to implement signal conditioning, buffering, voltage comparison, summing, or instrumentation functions when the required bandwidth and precision remain within the device's published ratings. Key characteristics include four amplifier circuits in one package, a 1.2 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. These figures make the device suitable for low-to-moderate-frequency analog signals rather than high-speed video or precision signal-chain applications. The 3 mV offset-voltage listing is particularly relevant when evaluating DC accuracy, while the wide ±1.5 V to ±16 V supply range supports both single-supply and split-supply arrangements. The LM224A device family uses high-gain, internally frequency-compensated amplifiers. Compensation avoids the need for an external dominant-pole capacitor in typical closed-loop uses, simplifying analog circuit design. Because all four channels share one package, designers can also reduce board area when four similar amplifier functions are required. Single and split supplies are relevant because the same amplifier can support grounded or bipolar signal systems, subject to the published common-mode and output-swing limits. Typical uses include four-channel sensor conditioning, low-frequency active filters, industrial control interfaces, general-purpose signal buffers, comparators with positive feedback, and analog summing networks. In each case, designers should verify noise, input bias current, common-mode range, output swing, stability, and load-driving capability against the manufacturer datasheet because those values are not present in the supplied source data. The primary design consideration is ensuring that signal bandwidth and amplitude remain compatible with the 1.2 MHz bandwidth and 0.5 V/µs slew rate. Place decoupling capacitors close to the supply pins, maintain a quiet ground reference, and route sensitive input signals away from high-current switching nodes. The complete 14-pin pin assignment and published limits should be checked in the manufacturer datasheet before layout release. This page combines the verified LM224A and LM224ADR listings with distributor package information, same-package replacement candidates, and practical design guidance. It distinguishes documented ratings from parameters that still require direct confirmation from the official LM224 datasheet, avoiding unsupported assumptions about electrical performance, compliance, or stock status.

RFQ İletişim
LM224ADRE4 - Quad 32V 1.2MHz Op Amp | Texas Instruments
LM224ADRE4

LM224ADRE4 - Quad 32V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM224ADRE4 is a four-channel, high-gain operational amplifier IC with a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and supply-voltage operation from 3 V to 32 V. The device is packaged in a 14-pin SOIC and supports general-purpose signal conditioning across industrial, instrumentation, sensor, and control applications. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM224 family belongs to the broader hierarchy of amplifier ICs, analog signal-conditioning ICs, and semiconductors. Internally frequency-compensated amplifiers simplify closed-loop design by removing the need for an external dominant-pole capacitor in many conventional gain configurations. The LM224ADRE4 provides four high-gain amplifiers in one package, allowing a design to use several independent analog channels without allocating separate single or dual amplifier packages. Typical input offset voltage is 2 mV, typical input bias current is 2 nA, and typical supply-current drain is 0.8 mA. Its common-mode input range includes ground, which supports direct sensing of signals near the negative supply rail. The 1.2 MHz gain-bandwidth product defines the frequency range available for closed-loop amplification and is particularly useful for low- to moderate-frequency signal paths. A 0.5 V/µs slew rate supports accurate output transitions in amplifier networks that process bipolar, sensor, or control signals. Four amplifiers in one 14-pin SOIC can also reduce board area and simplify assembly compared with four separate single-amplifier packages. Typical uses include temperature and pressure sensor interfaces, low-level signal conditioning, industrial control loops, instrumentation, and general voltage amplification. In sensor applications, the amplifier can convert a small transducer voltage into a larger signal suitable for an ADC or controller. In control systems, the four channels can support conditioning, active filtering, error amplification, and output buffering within one circuit board. For reliable operation, maintain adequate supply headroom and verify that input and output voltage excursions remain within the common-mode and output limits stated in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance so that oscillation, offset, or saturation does not affect the assembled circuit.

RFQ İletişim
LM224ADRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM224ADRG4

LM224ADRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM224ADRG4 is a general-purpose quadruple operational amplifier with four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 3 mV typical input offset voltage, and operation across a -25°C to 85°C temperature range. The device is supplied in a 14-pin SOIC (D) package for surface-mount assembly. A general-purpose operational amplifier is an analog signal-conditioning IC used to amplify voltage differences, buffer sensor outputs, or implement feedback-controlled analog circuits. In the hierarchy of electronic components, an operational amplifier belongs to the amplifier IC class, the larger analog and mixed-signal IC category, and ultimately the semiconductor family. Its internal gain is frequency dependent, so closed-loop bandwidth depends on the selected feedback network and noise gain. The LM224A family provides four amplifiers in one package, allowing a compact PCB design to implement several independent analog functions. Its 1.2 MHz gain-bandwidth product supports general-purpose signal processing rather than high-speed precision instrumentation. The specified 3 mV input offset voltage is important when signals are small or when multiple stages must operate with controlled dc error. A 30 V maximum supply rating and ±16 V or 32 V operating supply descriptions cover conventional industrial supply environments. Each amplifier is internally frequency compensated, simplifying implementation of standard inverting, non-inverting, summing, and comparator-style signal-processing arrangements. The package pinout follows the conventional quad operational-amplifier arrangement, with power, ground, four differential inputs, and four outputs. Because input offset, bias current, common-mode range, output swing, supply current, and noise are not stated in the product listing excerpts, consult the manufacturer datasheet before finalizing precision biasing, output-swing, or stability calculations. Typical uses include industrial control and instrumentation, four-channel sensor conditioning, audio preamplification, power-supply feedback, sample-and-hold support circuits, and general mixed-signal interfaces. The four independent channels make the device especially useful when a design needs several similar low-frequency analog stages without allocating separate single-amplifier packages. For a new layout, route each input and output according to the manufacturer pin-description table, place input and output decoupling capacitors close to the supply pins, and verify stability with the intended feedback network and load. This page combines ordering information, verified device characteristics, drop-in family alternatives, comparison details, and practical implementation guidance for faster component selection and PCB planning.

RFQ İletişim
LM224AN - 30V Quad Op Amp, 1.2MHz | Texas Instruments
LM224AN

LM224AN - 30V Quad Op Amp, 1.2MHz | Texas Instruments

The Texas Instruments LM224AN is a four-channel, internally compensated operational amplifier with a 30 V maximum supply rating, 1.2 MHz unity-gain bandwidth, and 3 mV input offset voltage, housed in a 14-pin PDIP package. It is designed for general-purpose analog signal conditioning from single- or dual-supply circuits. The four independent amplifiers share common supply and ground pins but otherwise provide separate input and output connections. An operational amplifier is a high-gain, analog differential-input amplifier intended for feedback-based signal conditioning. The LM224 belongs to the operational-amplifier hierarchy within analog and linear integrated circuits. Internally compensated amplifiers simplify closed-loop design because no external compensation network is required for ordinary unity-gain or inverting-amplifier configurations. Single-supply operation permits the output to approach ground, while split-supply operation supports bipolar signal processing around a zero-volt reference. The LM224AN provides four amplifiers in one 14-pin PDIP package, helping reduce board area compared with four individual single amplifiers. Its specified unity-gain bandwidth of 1.2 MHz supports moderate-frequency signal conditioning, while internally distributed compensation permits operation without an external frequency-compensation capacitor. The 3 mV offset specification characterizes the input mismatch that can appear as a DC error in high-gain feedback configurations. A 30 V maximum supply rating accommodates higher-voltage industrial and legacy analog systems when operating constraints and dissipation are properly evaluated. The device is suitable for audio tone control, analog signal conditioning, sensor interfaces, control loops, and general instrumentation. Four independent channels allow an instrumentation amplifier, instrumentation signal-conditioning stage, multi-axis sensor interface, or four-channel measurement circuit to use one package. The PDIP package also facilitates prototyping, inspection, and replacement during maintenance because its leads are accessible and compatible with conventional through-hole assembly methods. When designing with the LM224AN, confirm the actual operating supply voltage, load current, input common-mode range, output swing, and thermal dissipation under worst-case conditions. Input and output stability depend on load capacitance and source resistance, so breadboard and long-lead prototypes should be checked with an oscilloscope before production. Decoupling capacitors should be placed close to the supply and ground pins to limit supply ripple and prevent unintended feedback through board parasitics. This page consolidates verified manufacturer and distributor information, same-package drop-in alternatives, specification comparisons, and practical design guidance. It distinguishes documented LM224AN facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers evaluate replacements without treating every electrically similar amplifier as a guaranteed drop-in substitute.

RFQ İletişim
LM224D - Quad General-Purpose Op Amp | Texas Instruments
LM224D

LM224D - Quad General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM224D is a standard general-purpose, four-circuit operational amplifier in a 14-SOIC package. The verified distributor result identifies it as a 4-circuit amplifier, while the manufacturer describes the LM224 as a high-performance operational amplifier designed for wide-temperature-range operation. The LM224D combines four independent amplifiers in one package, making it suitable for signal conditioning, instrumentation, sensor interfaces, and industrial control systems. An operational amplifier is an analog signal-processing component that uses high open-loop gain and negative feedback to amplify or process small voltage signals. A quad operational-amplifier package such as the LM224D provides four amplifier sections in one integrated circuit, reducing component count and simplifying PCB layout. Each section can be configured independently as an amplifier, buffer, comparator, or active filter, subject to the device's operating and common-mode limits. The LM224 family is intended for general-purpose analog designs rather than precision or high-speed signal paths. The verified sources specifically identify wide-temperature-range operation and broad supply-voltage capability, making the device relevant to industrial, instrumentation, and test-equipment applications. The 14-SOIC package is a standard surface-mount package with widely used lead spacing, but the exact pin names and electrical limits must be taken from the manufacturer datasheet before final PCB release. The LM224D is useful in low-frequency control loops, sensor conditioning, transducer interfaces, current-voltage conversion, and general instrumentation. Because the available verified data does not state the complete output-current capability, input-bias current, gain-bandwidth product, common-mode range, or exact temperature limits, those values are intentionally not inferred here. The design should account for the amplifier's supply voltage, output swing, input offset, noise, and stability requirements. For PCB implementation, place the device close to the signals it processes and provide adequate bypassing on the supply pins. Decoupling capacitors should be placed at the power-entry points, with short return paths and careful treatment of analog ground versus power ground. Avoid using the LM224D for high-frequency signal chains unless the complete datasheet confirms the required bandwidth and settling behavior. This page combines the verified manufacturer and distributor identity, package information, application context, and engineering guidance. It intentionally separates confirmed data from parameters requiring datasheet confirmation, helping engineers identify the LM224D quickly while avoiding unsupported assumptions.

RFQ İletişim
LM224DG - 4-Channel 1 MHz Op Amp | onsemi | Industrial Control
LM224DG

LM224DG - 4-Channel 1 MHz Op Amp | onsemi | Industrial Control

The onsemi LM224DG is a four-channel general-purpose operational amplifier with true differential inputs, a 1 MHz gain-bandwidth product, and a 14-pin SOIC package. It operates from 3 V to 32 V and supports single-supply or split-supply operation, making it suitable for industrial control, instrumentation, sensor interfaces, and test equipment. The device combines four amplifiers in one package to reduce board area and simplify multi-channel designs. An operational amplifier is a high-gain differential-input amplifier commonly used to buffer sensors, amplify small signals, implement active filters, and drive higher-impedance loads. The LM224 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers and is used within analog signal-chain and power-management systems. Its four channels can be used independently when the required circuit functions do not interfere. Key verified features include four amplifier circuits, a 1 MHz gain-bandwidth product, a 3 V to 32 V operating supply range, true differential inputs, and a minimum common-mode rejection ratio of 70 dB. The listed input-offset voltage is 5 mV. These characteristics make the LM224DG appropriate for general-purpose signal conditioning where a wide supply range and multiple analog channels are more important than precision or low-noise performance. The LM224 series is designed for low-cost, general-purpose applications and supports operation from a single power supply or split supplies. This flexibility allows engineers to interface signals around ground or operate from an industrial supply without requiring negative rails. Its internal frequency compensation simplifies closed-loop amplifier design, although stable operation still depends on suitable feedback networks and load conditions described by the manufacturer. Typical applications include sensor-signal conditioning, current-loop measurement, industrial process-control modules, data-acquisition systems, and general test equipment. The 14-pin SOIC package is also convenient for through-hole assembly and conventional hand-soldering. Because the LM224 is a general-purpose amplifier, precision instrumentation may require careful offset, bias-current, noise, and common-mode analysis before finalizing the signal chain. When designing around the LM224DG, verify input and output voltage limits for the selected dual or single supply, check that connected loads remain within the amplifier's drive capability, and reserve suitable bypass capacitance close to the supply pins. Stable feedback and compensation arrangements should be copied from the manufacturer datasheet rather than copied blindly from unrelated op-amp circuits. This page combines the verified distributor and manufacturer-linked information for LM224DG with same-package drop-in alternatives, comparison parameters, and practical selection guidance. It highlights where the LM224's wide supply range and four-channel integration are useful, while making uncertainty in unavailable electrical details explicit.

RFQ İletişim
LM224DG4 - Quad General-Purpose Op Amp | Texas Instruments
LM224DG4

LM224DG4 - Quad General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM224DG4 is a standard general-purpose quadruple operational amplifier containing four independent amplifier circuits in a 14-pin SOIC package. It is designed for instrumentation, signal-conditioning, buffer-amplifier, and general analog-control applications where a multi-amplifier package simplifies PCB routing and reduces the number of individual components. The LM224 family operates across a 3 V to 32 V supply range and is suitable for single-supply or split-supply circuit arrangements. An operational amplifier is a voltage-gain device that uses differential feedback to amplify the difference between two input voltages. The LM224DG4 belongs to the operational-amplifier hierarchy, combining four high-gain, internally compensated amplifier channels in one integrated circuit. This quad-channel arrangement is useful when a system needs several closely related signal-processing stages, such as sensor conditioning, active filtering, or buffering multiple analog channels. The principal benefit of the four-channel architecture is board-space efficiency. Instead of placing four separate single op amps on a PCB, a designer can use one 14-SOIC device and distribute the amplifier channels according to signal flow. The standard general-purpose classification makes the LM224DG4 appropriate for non-specialized analog functions, although precision requirements should be checked against the manufacturer's electrical characteristics before selecting it for high-accuracy instrumentation. The wide 3 V to 32 V operating range provides flexibility for industrial, instrumentation, sensing, and test-equipment designs. Operation from a single positive supply simplifies circuits where the signal is referenced to ground, while split supplies can support bipolar signal processing. Because four amplifiers share one package, power-supply routing and decoupling must be designed to keep common supply impedance and package-level heating low. Typical uses include sensor-interface amplifiers, low-frequency active filters, analog signal conditioners, transducer amplifiers, sample-and-hold support circuits, and general-purpose buffers. The LM224DG4 is especially useful when multiple amplifier channels are required but the precision, speed, noise, or rail-to-rail performance of a specialized amplifier is not required. Designers should verify input common-mode range, output swing, supply current, slew rate, and stability requirements against the Texas Instruments LM224 product documentation. Place the package power pins and bypass capacitor according to the datasheet guidance, maintain adequate operating area for thermal dissipation, and avoid relying on rail-to-rail operation unless the selected grade explicitly supports it. This product page combines package information, application guidance, drop-in replacement analysis, comparison parameters, and practical layout notes. It is intended to accelerate engineering selection while directing detailed verification to the manufacturer datasheet and pin-description tables.

RFQ İletişim
LM224DR - Quad General-Purpose Op Amp | Texas Instruments (Tape & Reel)
LM224DR

LM224DR - Quad General-Purpose Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM224DR is a standard general-purpose, four-circuit operational amplifier in a 14-SOIC package. The verified distributor result identifies it as a 4-circuit amplifier, while the manufacturer describes the LM224 as a high-performance operational amplifier designed for wide-temperature-range operation. The LM224DR combines four independent amplifiers in one package, making it suitable for signal conditioning, instrumentation, sensor interfaces, and industrial control systems. An operational amplifier is an analog signal-processing component that uses high open-loop gain and negative feedback to amplify or process small voltage signals. A quad operational-amplifier package such as the LM224DR provides four amplifier sections in one integrated circuit, reducing component count and simplifying PCB layout. Each section can be configured independently as an amplifier, buffer, comparator, or active filter, subject to the device's operating and common-mode limits. The LM224 family is intended for general-purpose analog designs rather than precision or high-speed signal paths. The verified sources specifically identify wide-temperature-range operation and broad supply-voltage capability, making the device relevant to industrial, instrumentation, and test-equipment applications. The 14-SOIC package is a standard surface-mount package with widely used lead spacing, but the exact pin names and electrical limits must be taken from the manufacturer datasheet before final PCB release. The LM224DR is useful in low-frequency control loops, sensor conditioning, transducer interfaces, current-voltage conversion, and general instrumentation. Because the available verified data does not state the complete output-current capability, input-bias current, gain-bandwidth product, common-mode range, or exact temperature limits, those values are intentionally not inferred here. The design should account for the amplifier's supply voltage, output swing, input offset, noise, and stability requirements. For PCB implementation, place the device close to the signals it processes and provide adequate bypassing on the supply pins. Decoupling capacitors should be placed at the power-entry points, with short return paths and careful treatment of analog ground versus power ground. Avoid using the LM224DR for high-frequency signal chains unless the complete datasheet confirms the required bandwidth and settling behavior. This page combines the verified manufacturer and distributor identity, package information, application context, and engineering guidance. It intentionally separates confirmed data from parameters requiring datasheet confirmation, helping engineers identify the LM224DR quickly while avoiding unsupported assumptions.

USD $0,16 Stokta
LM224DR2 - Quad 3-32V Operational Amplifier | onsemi
LM224DR2

LM224DR2 - Quad 3-32V Operational Amplifier | onsemi

onsemi LM224DR2 is a four-channel, general-purpose operational amplifier designed for single-supply operation from 3 V to 32 V. The device uses true differential inputs and internally frequency-compensated amplifiers, with four amplifiers contained in a 14-pin SOIC package. It belongs to the LM224 family of low-cost quad operational amplifiers for industrial signal-conditioning and control systems. An operational amplifier is a voltage-gain element that compares its differential input voltage and drives its output to represent the amplified difference between those inputs. Within the amplifier-IC hierarchy, the LM224DR2 is a quad operational amplifier, meaning four independent amplifier channels share one package. This integration reduces board area while retaining separate inputs and outputs for instrumentation, buffering, filtering, and closed-loop control functions. The principal operating characteristics are a 3 V to 32 V single-supply range, four amplifier channels, true differential input capability, and a 14-pin SOIC package. The quad organization allows one package to implement a multi-stage signal path or several independent control channels. Its wide supply range also permits operation from common industrial rails, although the circuit must retain the voltage headroom required by the selected feedback network and load. The LM224 series architecture is based on internally compensated, high-gain amplifier stages. Internal frequency compensation removes the need for an external compensation capacitor in the standard closed-loop configurations. True differential inputs support direct sensing of a sensor or bridge signal, while the broad supply range supports both single-rail and split-supply arrangements when the total supply span and common-mode limits are satisfied. Typical uses include temperature and pressure sensor conditioning, current-loop receivers, industrial process-control loops, low-level signal buffers, active filters, and general-purpose instrumentation. The four channels can process related signals in one package or provide independent gain stages. When the source impedance is high, input-bias-current effects must be considered, and when driving a capacitive load, stability should be checked with the load and output-network configuration included in the analysis. For robust PCB implementation, place the device on a stable analog ground plane, keep input and feedback traces short, and avoid routing sensitive input nodes beneath switching nodes or high-current return paths. Bypass the supply pins locally with the capacitance recommended by the manufacturer datasheet. When replacing LM224DR2 on an existing board, verify the SOIC-14 footprint, pin orientation, supply limits, input common-mode range, output swing, and required output current before finalizing the substitution. This product page combines the verified manufacturer and distributor information for LM224DR2 with application guidance, package details, design considerations, and technically constrained drop-in comparisons. It is intended to help engineers identify the correct amplifier family, verify footprint compatibility, and evaluate whether an alternative meets the electrical and temperature requirements of the target circuit.

RFQ İletişim
LM224DR2G - 4-Channel 3-32V Op Amp | onsemi
LM224DR2G

LM224DR2G - 4-Channel 3-32V Op Amp | onsemi

The onsemi LM224DR2G is a four-channel general-purpose operational amplifier rated for single-supply operation from 3 V to 32 V, with a gain-bandwidth product of 1 MHz and a slew rate of 0.6 V/us, housed in a 14-pin SOIC package. The four amplifiers can operate from a common supply, making the device suitable for compact analog signal-processing systems that require several independent amplifier channels. A general-purpose operational amplifier is a voltage-amplified, high-gain active device commonly used for signal conditioning, buffering, comparisons, instrumentation, and closed-loop feedback control. Within the semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. It provides a practical combination of high open-loop gain, differential input capability, and output-voltage swing, allowing simple external feedback networks to define the closed-loop behavior. The LM224 series provides four true differential-input amplifiers in one package. Its stated 1 MHz gain-bandwidth product supports general-purpose signal amplification at low and moderate frequencies, while the 0.6 V/us slew rate governs large-signal response. Operation from 3 V to 32 V covers both low-voltage circuits and conventional industrial supply levels. The Mouser listing identifies the LM224DR2G as a low-power quad operational amplifier with a -25°C to 85°C temperature range. Because each amplifier shares the same package and supply rails, designers can reduce component count and board area in applications requiring several similar channels. The 14-pin SOIC format also supports conventional surface-mount assembly and is compatible with automated inspection and pick-and-place processes. True differential inputs allow each channel to accept signals referenced to the circuit ground without requiring a separate input common-mode arrangement for every channel. Typical uses include four-channel sensor conditioning, general-purpose signal buffering, instrumentation interfaces, industrial control signal paths, and low-frequency analog measurement systems. Four matched functional channels can simplify a design that needs to process or monitor several related signals. The device is most appropriate when moderate bandwidth, straightforward feedback networks, and wide supply-voltage flexibility matter more than very high speed or very low offset voltage. Design the bypass capacitance and input network to limit parasitic coupling between adjacent channels. Keep sensitive input traces short, place the supply-bypass capacitor close to the positive and ground pins, and maintain signal returns away from switching nodes. Verify common-mode and output-swing limits against the selected 3 V to 32 V supply before using the amplifier near a rail, because those operating limits determine whether a particular feedback configuration remains linear. This page combines the manufacturer-family characteristics with package, supply, temperature, frequency, and sourcing information, and adds practical channel-level design guidance for evaluating the LM224DR2G in industrial and instrumentation applications.

RFQ İletişim
LM224DT - 4-Channel 1.3MHz Op Amp | STMicroelectronics
LM224DT

LM224DT - 4-Channel 1.3MHz Op Amp | STMicroelectronics

STMicroelectronics LM224DT is a general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers with a gain bandwidth product of 1.3 MHz, input offset voltage up to 7 mV, and operation from a single 3 V to 30 V supply in a 14-pin SOIC package. The LM224DT is designed for instrumentation, buffer-amplifier, and general signal-conditioning applications. An operational amplifier is a high-gain differential amplifier whose feedback network determines its closed-loop behavior. The LM224 family belongs to the linear-amplifier hierarchy: operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and semiconductor. Its four amplifiers can operate independently, allowing one package to implement multiple filtering, amplification, comparison, or buffering functions while also supporting split-supply operation. Key features include four independent channels, internal frequency compensation, a 1.3 MHz gain bandwidth product, low input bias current, and low power-supply current. The wide 3 V to 30 V operating range permits use with 5 V, 12 V, 15 V, and 24 V supply systems. The device is available in the 14-pin SOIC outline identified by the T packaging suffix. Each channel uses an internally compensated architecture that simplifies closed-loop design without an external frequency-compensation network. Input offset voltage is specified up to 7 mV, while the gain bandwidth product determines how quickly a closed-loop circuit can amplify signals. The amplifiers are intended for general-purpose precision rather than high-speed or high-current applications, making them suitable for slow sensor signals and buffered control systems. Typical uses include industrial sensor interfaces, low-frequency active filters, transducer amplifiers, audio and communication buffers, battery-powered instrumentation, and four-channel process monitoring. A single package can reduce board area when four independent analog channels are required, although thermal management and input common-mode limits remain important when operating from higher supply voltages. Designers should verify input and output common-mode ranges, output swing, supply current, and stability for the intended load using the manufacturer datasheet. Input and output decoupling should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage to prevent unstable operation. This page combines verified distributor and manufacturer information, pin-level guidance, practical application notes, and drop-in replacement analysis. It also distinguishes electrically compatible replacements from merely similar amplifiers, helping engineers choose a replacement by package, pinout, supply range, bandwidth, and system requirements.

RFQ İletişim
LM224DTBG - Low-Power Quad Op Amp, 3-32 V | onsemi
LM224DTBG

LM224DTBG - Low-Power Quad Op Amp, 3-32 V | onsemi

onsemi LM224DTBG is a low-power, general-purpose quad operational amplifier with four amplifier channels, a 3 V to 32 V supply-voltage range, and a 14-pin TSSOP package. The device is specified for operation from -25°C to +85°C and is intended for instrumentation, buffering, and general-purpose signal-conditioning applications. An operational amplifier, or op amp, is an integrated voltage amplifier whose open-loop gain and feedback behavior allow it to perform precision amplification, buffering, summation, integration, and filtering. A quad operational amplifier combines four amplifiers in one package, allowing compact implementation of multi-channel analog systems. Within the component hierarchy, the LM224 belongs to the operational-amplifier, analog-amplifier, analog-signal-conditioning, and integrated-circuit categories. The LM224DTBG provides four independent general-purpose amplifier channels in one 14-TSSOP package, reducing external component count and board area compared with four separate single or dual amplifier packages. Its stated 3 V to 32 V operating range supports both lower-voltage and higher-voltage analog systems. The -25°C to +85°C temperature specification supports industrial-temperature applications where the operating environment exceeds the commercial range. The quad-channel architecture is particularly useful when four related analog signals must be conditioned under common supply and layout constraints. Because all four amplifiers share one package, power routing and grounding can be organized consistently across the device. Designers should still evaluate each channel independently for output swing, input common-mode range, noise, stability, and load-drive requirements during final circuit verification. Typical uses include sensor-signal conditioning, transducer-buffer interfaces, analog measurement chains, audio and communication equipment, low-frequency active filtering, and general instrumentation. The LM224DTBG can also serve as a quad amplifier in industrial control systems where three or four channels are needed for excitation, sensing, filtering, or output buffering without using multiple packages. PCB implementation requires careful attention to feedback-loop stability, input and output grounding, and decoupling. Place the power-supply bypass capacitor close to the supply pins, keep feedback traces short, and avoid routing sensitive inputs beside high-current outputs. Because the package exposes 14 terminals in a compact TSSOP footprint, inspect land patterns and solder-paste design before assembly. This product page consolidates the exact package, channel count, supply range, temperature range, sourcing information, drop-in comparison, and application guidance for LM224DTBG. It also provides practical selection criteria for comparing this onsemi quad amplifier with the documented LM224DTBR2G alternative and with pin-compatible single-supply amplifier families.

RFQ İletişim
LM224DTBR2 - Quad 3-32V Op Amp | onsemi | Industrial
LM224DTBR2

LM224DTBR2 - Quad 3-32V Op Amp | onsemi | Industrial

The onsemi LM224DTBR2 is a general-purpose, four-circuit operational amplifier designed for single-supply operation from 3 V to 32 V and supplied in a 14-pin TSSOP package. It provides four independent amplifier channels, true differential inputs, and a common ground arrangement suited to general-purpose analog signal conditioning. The device combines straightforward implementation with a broad supply range, making it useful in industrial controls, sensor interfaces, audio paths, and low-cost instrumentation. An operational amplifier, commonly abbreviated op amp, is a voltage-controlled differential amplifier. Its inverting and non-inverting inputs allow a circuit to amplify or attenuate a signal while establishing feedback-defined gain. Within the broader semiconductor hierarchy, the LM224DTBR2 belongs to the linear amplifier family, which sits within analog integrated circuits used for instrumentation, buffering, amplification, and signal conversion. The four channels also allow several analog functions to be implemented in one compact package. Key characteristics include a 3 V to 32 V operating supply, four amplifier circuits, true differential input capability, and a 14-pin TSSOP surface-mount package. The wide supply range allows the same device to operate from low-voltage analog systems through higher industrial rails. Its four-channel architecture reduces the number of packages required when an application needs multiple independent gain stages, although the common device supply and ground must still support every channel's operating requirements. The LM224 series is intended for general-purpose applications rather than precision instrumentation or high-speed signal processing. Its internal architecture supports common amplifier configurations, including non-inverting, inverting, voltage follower, summing, and difference stages. Designers should account for input common-mode limits, output swing, bias current, noise, and stability requirements when selecting external resistor and capacitor values. Operating from a single supply is particularly convenient in systems that do not provide a negative analog rail. Typical uses include conditioning sensors, buffering inputs to analog-to-digital converters, amplifying low-level control signals, implementing simple filters, and providing multiple analog channels in industrial or embedded equipment. It can also participate in audio preamplifier and mixer circuits when the required bandwidth, output swing, and distortion meet the application. Four amplifiers in one package are particularly helpful where board area is limited and several independent analog functions are required. PCB design should provide a short return path to the ground pin and place decoupling capacitance close to the supply connection. Because all four channels share package-level supply pins, high-current output stages and sensitive input stages may require careful partitioning to prevent supply disturbance from appearing as signal noise. Stable operation also depends on suitable feedback networks and adherence to the layout and compensation guidance in the manufacturer datasheet. This page combines the LM224DTBR2 ordering information with practical guidance on package compatibility, replacement decisions, analog layout, and application selection. It is intended to help engineers determine whether the four-channel, single-supply amplifier is suitable for a new design and whether a documented alternative can preserve an existing 14-pin TSSOP footprint.

RFQ İletişim
LM224J - 1MHz Quad 32V Op Amp | Texas Instruments
LM224J

LM224J - 1MHz Quad 32V Op Amp | Texas Instruments

The Texas Instruments LM224J is a general-purpose, internally frequency-compensated quad operational amplifier rated for 32 V operation, with a 1 MHz gain-bandwidth product and 0.5 V/µs slew rate. The device contains four amplifiers in a 14-pin CDIP package, and distributor results identify the orderable LM224J as a tube-packaged, military-temperature variant. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify voltage differences. The LM224 belongs to the voltage-feedback operational-amplifier hierarchy and can support closed-loop signal conditioning, sensing, buffering, and control functions. Internally frequency compensation removes the need for an external compensation network in common non-inverting and inverting amplifier configurations. Key features include four independent amplifier sections, support for single or split supplies, a 1 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. The verified distributor result describes a 32 V maximum supply-related rating, while another result reports operating from approximately ±1.5 V to ±16 V. These ranges describe complementary supply arrangements rather than conflicting absolute limits. Technically, the LM224J uses a voltage-feedback architecture intended for general-purpose low-frequency signal paths. Its four channels provide useful channel density for multi-axis sensing, multi-channel conditioning, instrumentation, and embedded control. Because the verified results do not provide complete rail-to-rail, input-bias-current, offset-voltage, noise, or common-mode data, engineers should consult the official LM224 datasheet before setting precision or current-budget limits. Typical uses include transducer buffering, temperature-signal conditioning, low-frequency filtering, industrial control, test equipment, and four-channel sensor interfaces. The 14-CDIP package favors through-hole industrial or legacy-style assemblies rather than compact surface-mount production. Design with adequate output-current margin, stable feedback compensation for the selected gain and load, and supply-bypass capacitors placed close to the package. Check all electrical limits against the official datasheet, especially when using long feedback traces, high-value resistors, or low-noise sensor interfaces. This page consolidates distributor availability, verified package and performance details, practical circuit guidance, and replacement analysis that are not presented together in the manufacturer product-page snippet.

RFQ İletişim
LM224J/NOPB - 4-Op-Amp, 1MHz, 14-CDIP | Texas Instruments
LM224J/NOPB

LM224J/NOPB - 4-Op-Amp, 1MHz, 14-CDIP | Texas Instruments

Texas Instruments LM224J/NOPB is a four-circuit general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.5 V/µs slew rate, and internal frequency compensation, supplied in a 14-CDIP package. It operates from a single supply or split supply over a 3 V to 32 V range and is designed for instrumentation, sensor conditioning, and low-frequency signal-processing applications. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify voltage differences. The LM224 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Four independent amplifiers are integrated into one package, allowing a circuit to perform gain, buffering, comparison, summation, filtering, and transducer-signal conditioning without using four separate packages. The LM224 combines four general-purpose amplifiers with low-power operation, internally compensated closed-loop stability, and support for both single- and split-supply systems. Its 1 MHz gain-bandwidth product is suitable for audio-frequency and general instrumentation tasks, while its 0.5 V/µs slew rate limits large-signal performance in fast transient applications. The 14-CDIP package provides through-hole mounting for conventional industrial and laboratory boards. Each of the four circuits has independent input, output, and power connections, while the common supply architecture permits operation from a single rail or from positive and negative rails. Internal frequency compensation removes the need for an external dominant-pole capacitor in the standard closed-loop configurations. Engineers can therefore use stable unity-gain voltage-follower, non-inverting, and inverting amplifier arrangements without redesigning compensation networks. Typical uses include low-frequency sensor signal conditioning, process-control instrumentation, audio preamplification, active filtering, data acquisition, and general test equipment. The same quad-amplifier organization allows one package to implement several stages, reducing component count and simplifying interstage routing on a through-hole circuit board. When designing around the LM224J/NOPB, verify input and output common-mode limits for the selected supply voltage, maintain the required output-current margin, and include suitable bypassing close to the supply pins. The 1 MHz bandwidth and 0.5 V/µs slew rate make it more appropriate for low-frequency precision conditioning than for wideband video, RF, or high-speed data acquisition. This product record combines package, electrical, application, replacement, and engineering guidance in one place. It also identifies the distinction between electrically compatible quad amplifiers and true same-package drop-in choices, helping engineers evaluate PCB reuse, supply compatibility, temperature grade, and signal-bandwidth requirements before releasing a replacement into production.

RFQ İletişim
LM224J4 - Quad 1MHz Operational Amplifier | Texas Instruments
LM224J4

LM224J4 - Quad 1MHz Operational Amplifier | Texas Instruments

Texas Instruments LM224J4 is a four-circuit, general-purpose operational amplifier in a 14-CDIP through-hole package, with a 1 MHz gain-bandwidth product and 0.5 V/µs slew rate. The four amplifiers are internally frequency compensated and designed for general-purpose analog signal conditioning from a single power supply. The LM224 family is recognized for its wide operating-temperature capability and straightforward through-hole footprint. An operational amplifier is a high-gain analog building block that compares two input voltages and amplifies their difference. The LM224J4 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, analog signal-conditioning ICs, and broader analog semiconductors. Internally compensated amplifiers simplify closed-loop design because the compensation network is integrated rather than added externally. The main features of the LM224J4 are its four independent amplifier sections, 1 MHz gain-bandwidth product, 0.5 V/µs slew rate, and internally compensated operation. These characteristics make it appropriate for low-to-moderate frequency signal paths where straightforward voltage feedback, buffering, amplification, and analog comparisons are needed. The 14-CDIP package also provides a through-hole format that is convenient for prototyping, educational equipment, legacy control systems, and industrial maintenance boards. Each amplifier section provides separate input and output pins, while the IC also exposes shared supply connections. Using multiple amplifiers within one package can reduce board area compared with four separate single-amplifier ICs. The tradeoff is that a fault or excessive power dissipation affecting one section can also affect the shared package, so the complete circuit must be evaluated for supply-current and thermal-budget requirements. Typical uses include industrial sensor conditioning, low-frequency control loops, current-to-voltage conversion, transducer amplification, audio preamplification, and general-purpose laboratory interfaces. The LM224J4 is particularly useful where a 1 MHz bandwidth is sufficient but a high-speed op amp would add unnecessary cost, complexity, or switching-related demands. For a new through-hole design, verify the full ordering code, package drawing, supply limits, output-current behavior, input-common-mode range, and temperature grade against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured according to the manufacturer guidance rather than left floating. This page combines verified distributor and manufacturer information with package, purchasing, comparison, and practical design guidance. It also distinguishes the LM224J4 from related amplifier and temperature-grade options so engineers can identify a genuine same-package replacement before committing a PCB revision.

RFQ İletişim
LM224KAD - 4-Channel 32V Op Amp | Texas Instruments
LM224KAD

LM224KAD - 4-Channel 32V Op Amp | Texas Instruments

Texas Instruments LM224KAD is a four-channel general-purpose operational amplifier designed for single-supply or dual-supply operation. It supports supply voltages from 3 V to 32 V, corresponding to ±16 V under symmetric dual-supply operation, and operates with a typical gain-bandwidth product of 1.2 MHz. The device is packaged in a 14-pin SOIC and is identified as the industrial-grade, standard quad amplifier option with improved electrostatic-discharge protection rated to 2 kV. An operational amplifier is an analog building block that uses high-gain differential amplification to compare an inverting input with a non-inverting input. When negative feedback is applied, the amplifier adjusts its output to reduce the difference between those inputs. The LM224 family belongs to the broader operational amplifier, analog signal-conditioning, and semiconductor hierarchies, providing a practical way to buffer sensors, amplify small signals, and implement general analog control functions. Four independent amplifier channels are integrated into one package, reducing board area in designs requiring multiple analog functions. The 1.2 MHz gain-bandwidth product supports common low-frequency signal-conditioning tasks, while the wide 3 V to 32 V operating range accommodates single 5 V, 12 V, 24 V, and ±15 V systems. A 14-pin SOIC provides a familiar surface-mount footprint for conventional PCB assembly and prototype rework. The product listing identifies 2 kV ESD protection, improving handling tolerance in applications exposed to electrostatic discharge. The LM224 architecture supports operation from a single positive supply or split supplies, allowing the same amplifier family to serve industrial control, instrumentation, and test-equipment designs. Its low-power general-purpose positioning makes it especially useful when four amplifiers are required but precision, rail-to-rail input/output, or very high bandwidth is not required. Input and output limits must still be respected, and the unused amplifier channel should be configured according to the manufacturer’s recommended practice rather than left floating. Typical uses include 24 V industrial sensor interfaces, temperature-transducer amplification, low-frequency active filters, actuator-signal conditioning, and instrumentation buffers. The wide supply range is particularly useful where the same board must operate across multiple nominal rails. In applications using ±15 V supplies, the device operates near the stated ±16 V capability, while designers should preserve margin for load regulation and transient behavior. When laying out a design, place input and feedback components close to the corresponding amplifier pins to minimize parasitic feedback and noise pickup. Decoupling capacitors should connect to a low-impedance ground plane, and unused channels need stable biasing. Input common-mode and output swing limits must be checked against the actual supply voltages because the LM224 is not a rail-to-rail amplifier. This page combines the exact LM224KAD order information, verified product attributes, family-level alternatives, and practical circuit-placement guidance. It also explains where the LM224 fits among general-purpose quad operational amplifiers, helping engineers distinguish it from higher-precision, low-noise, rail-to-rail, or wider-bandwidth amplifier families before making a drop-in sourcing decision.

RFQ İletişim
LM224KADG4 - 1.2MHz Quad Op Amp | Texas Instruments
LM224KADG4

LM224KADG4 - 1.2MHz Quad Op Amp | Texas Instruments

The Texas Instruments LM224KADG4 is a general-purpose quad operational amplifier with four independent, internally frequency-compensated amplifiers, a 1.2 MHz gain-bandwidth product, and a 14-SOIC package. It is designed for single-supply operation across industrial instrumentation, sensor conditioning, and low-frequency analog signal-processing systems. The device combines a wide operating-voltage range with low input bias current and output-current capability, making it suitable for applications requiring multiple amplifier channels on one PCB footprint. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A quad operational amplifier combines four amplifiers in one package, reducing component count and simplifying power distribution in designs that need several independent gain stages. The LM224KADG4 belongs to the general-purpose operational-amplifier family within the broader voltage-regulator and power-management-independent analog IC hierarchy. Its internal frequency compensation removes the need for an external compensation capacitor in typical closed-loop configurations. The principal features are a 1.2 MHz gain-bandwidth product, four amplifier channels, 14-SOIC packaging, low input bias current of approximately 15 nA, and output-current capability of approximately 30 mA per channel. These characteristics support accurate signal amplification in DC and low-frequency systems, including transducer interfaces, current-loop receivers, analog measurement circuits, and embedded control systems. The wide input common-mode range allows direct sensing near ground, which is important in battery-powered and single-supply equipment. Internally, the LM224 family uses a differential-input stage, voltage-amplification stage, and output stage optimized for general-purpose analog operation. Internal frequency compensation provides stable operation in common noninverting configurations when the recommended feedback network and gain limits are respected. The 14-pin gull-wing SOIC package is compatible with conventional surface-mount assembly and provides separate connections for each amplifier’s differential inputs, output, and supply pins. Typical applications include industrial sensor interfaces, temperature measurement, current sensing, process-control instrumentation, data-acquisition systems, audio preamplifier stages, and power-supply feedback loops. The quad organization is particularly useful when a design needs multiple buffered channels, such as four sensor inputs sharing one analog front end. Designers should maintain adequate input and output voltage headroom, check the common-mode and output-swing limits against the actual supply voltage, and provide stable bypass capacitance close to the supply pins. The 14-SOIC footprint requires adequate copper routing and thermal consideration when several channels operate continuously. This page summarizes the LM224KADG4’s verified device identity, package and analog specifications, drop-in alternatives, application guidance, and design considerations for engineers evaluating a quad general-purpose op amp.

RFQ İletişim
LM224KAN - Quad Operational Amplifier | Texas Instruments
LM224KAN

LM224KAN - Quad Operational Amplifier | Texas Instruments

The Texas Instruments LM224KAN is a standard general-purpose quadruple operational amplifier in a 14-pin PDIP package. It contains four independent, high-gain, internally frequency-compensated amplifiers designed to operate from a single supply or split supply over a wide voltage range. The device is intended for instrumentation, buffering, signal-conditioning, and general analog applications where a low-cost, temperature-tolerant amplifier is required. An operational amplifier is an analog building block that uses very high open-loop gain to amplify the difference between its inverting and non-inverting inputs. The LM224 family combines four amplifiers in one package, reducing board area and simplifying multi-channel designs. The device can support single-supply operation as well as positive and negative supply rails, which makes it useful in industrial control, instrumentation, test equipment, and sensor-interface circuits. The LM224KAN is specified for a 14-pin PDIP package and an operating temperature range of -25 °C to 85 °C. The verified product description identifies four amplifier circuits, a standard general-purpose amplifier configuration, and instrumentation or buffer-amplifier use. The LM224 family is associated with the next-generation LM324B and LM2902B families, whose B versions are described as drop-in replacements for earlier LM224, LM324, and LM2902 versions. Key application benefits include four amplifiers in one package, internal frequency compensation, operation from a single supply or split supply, and suitability for instrumentation and buffering. Because the LM224 is a conventional general-purpose amplifier rather than a precision or high-speed device, designers should account for its input offset voltage, input bias current, bandwidth, and output-current limitations when planning signal chains. The internal compensation also means that closed-loop stability is determined primarily by the feedback network and selected gain. Typical uses include sensor signal conditioning, low-level analog measurement, current-to-voltage conversion, audio and communications support circuitry, process-control modules, and educational or laboratory instrumentation. In a single-supply circuit, the input and output signal levels must remain within the amplifier's common-mode and output-swing limits; in a split-supply circuit, the positive and negative rails should be connected according to the manufacturer recommendations. For PCB layout, place the bypass capacitors close to the supply pins, keep input and feedback traces short, and avoid routing high-impedance signal lines beneath or beside power and output paths. The DIP package offers generous lead spacing and straightforward prototype insertion, although it occupies more board area than a surface-mount equivalent. This page combines the verified LM224KAN product data with practical design guidance for selecting, comparing, and implementing the part.

RFQ İletişim
LM224KD - Quad 1.2MHz Op Amp, 32V, 14-SOIC | Texas Instruments
LM224KD

LM224KD - Quad 1.2MHz Op Amp, 32V, 14-SOIC | Texas Instruments

Texas Instruments LM224KD is a four-circuit general-purpose operational amplifier with a 1.2 MHz gain-bandwidth product, support for ±16 V or 32 V total supply operation, and a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, in width. Each of its four independent, high-gain, frequency-compensated amplifiers can operate from a single supply or from split supplies. An operational amplifier is an analog signal-conditioning semiconductor that uses high open-loop gain and negative feedback to amplify small voltage differences. The LM224 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC hierarchy. Four amplifiers in one package can support independent gain stages, differential measurements, active filters, sensor conditioning, and general analog signal chains without requiring four separate packages. Key features include four amplifier circuits, a 1.2 MHz gain-bandwidth product, operation across a broad supply-voltage range, and 2 kV ESD protection. The amplifiers are internally frequency compensated, which simplifies the implementation of stable inverting, non-inverting, summing, and feedback-controlled circuits. The 14-SOIC package also provides a familiar leaded footprint for through-hole assembly and conventional surface-mount production. The LM224KD's single-supply capability is particularly useful in systems where a negative rail is unavailable. Its broad supply range permits operation from low-voltage analog systems as well as higher-voltage industrial and instrumentation circuits. Because it is a general-purpose device rather than a low-noise precision amplifier, designers should confirm input offset, input bias current, noise, and output-swing requirements for the specific measurement. Typical applications include sensor-signal conditioning, test and measurement equipment, industrial control interfaces, current-loop signal processing, audio preamplification, and four-channel analog monitoring. The device is also suitable for low-frequency filter stages where the 1.2 MHz bandwidth provides useful signal-path headroom. Design with the input common-mode range and output swing in mind, especially near the supply rails. Decoupling capacitors should be placed close to the supply pins, input and feedback resistors should preserve suitable noise and bias-current balance, and unused amplifier inputs must be tied to a defined potential rather than left floating. This product page combines manufacturer specifications, replacement cross-reference information, package-level guidance, and application-oriented design notes to support faster component selection and PCB implementation.

RFQ İletişim
LM224KDE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM224KDE4

LM224KDE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM224KDE4 is a general-purpose quadruple operational amplifier with four independent amplifiers, a 30 V supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection. It is packaged in a 14-pin SOIC and is specified for operation from -25°C to +85°C. An operational amplifier is an analog signal-conditioning integrated circuit that compares two input voltages and amplifies the difference between them. Its broader hierarchy is operational amplifier -> voltage-amplifier IC -> analog amplifier -> amplifier IC -> semiconductor. The LM224K combines four general-purpose amplifiers in one package, allowing a compact circuit to perform buffering, amplification, filtering, level shifting, and feedback-control functions. The principal features of the LM224KDE4 include four independent amplifier channels, operation from a single or split supply, a 30 V maximum supply rating, and a 1.2 MHz gain-bandwidth product. The improved 2 kV ESD protection helps the device tolerate electrostatic discharge exposure, while the -25°C to +85°C operating range supports industrial and extended-temperature applications. Each channel uses a differential input stage, high-gain voltage-amplification stage, and output stage optimized for general-purpose analog signal paths. Because the four amplifiers share a common supply architecture but operate independently, engineers can use them for simultaneous sensing, buffering, error amplification, or active filtering when sufficient decoupling is provided. Typical uses include industrial sensor interfaces, low-frequency active filters, transducer conditioning, control-loop error amplifiers, and general instrumentation. The 14-pin SOIC is also convenient for prototypes and repair assemblies because its four amplifiers can replace separate single or dual amplifier packages when board area is limited. For reliable operation, place the supply bypass capacitor close to the positive and ground pins and route high-current return paths away from sensitive input nodes. Check output swing, input common-mode range, load capability, and stability against the required signal amplitude before closing the feedback loop. This page combines manufacturer specifications, lifecycle information, package guidance, structured comparisons, and practical replacement guidance to support component selection, PCB layout, sourcing, and second-source qualification.

RFQ İletişim
LM224KDG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM224KDG4

LM224KDG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM224KDG4 is a quad operational amplifier with four independent, internally frequency-compensated amplifiers, a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and a 14-pin SOIC package. It is intended for general-purpose industrial signal conditioning where four amplifiers are needed in one package. According to the Texas Instruments product page, the LM224K family provides improved ESD protection of 2 kV and operates from -25 °C to +85 °C. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify small voltage differences. The LM224 belongs to the operational-amplifier hierarchy and provides four amplifier channels in one quad package. Each channel can amplify sensor, audio, or feedback signals independently. Internal frequency compensation makes the devices suitable for closed-loop designs without external compensation networks, although the available datasheet information should guide stability and unity-gain layout decisions. The LM224KDG4 combines four general-purpose amplifier channels with a maximum supply voltage of 30 V. Its 1.2 MHz gain-bandwidth product supports signal paths extending from low-frequency measurement circuits to moderate-bandwidth audio and control applications. The reported input offset voltage is 3 mV, a parameter that contributes to DC error when the amplifier operates near its input limits or in precision current-feedback measurements. The K suffix identifies an industrial temperature grade covering -25 °C to +85 °C. The four circuits share a common supply arrangement but otherwise operate independently, allowing one package to implement summing, buffering, amplification, filtering, or current-feedback stages. A listing identifies the device as a 14-SOIC surface-mount part with gull-wing terminals, while the ordering code G4 denotes its supplied packaging configuration. Typical uses include industrial process-signal conditioning, low-frequency sensor interfaces, audio preamplification, feedback networks in power converters, and general control systems. Four channels in one package can reduce PCB area and simplify multi-amplifier analog boards. The 30 V supply capability also accommodates industrial rails higher than conventional 5 V or 12 V systems, subject to the common-mode and output-swing limits stated in the manufacturer datasheet. PCB layout should keep input, feedback, and decoupling connections short, place the bypass capacitor close to the supply pins, and route sensitive input nodes away from switching and high-current paths. Because the LM224K is not rail-to-rail, verify input and output voltage ranges before choosing it for single-supply sensing near ground. This page combines package, temperature, bandwidth, and cross-reference information with practical guidance for evaluating same-footprint replacements.

RFQ İletişim