Ürünler (46.000+)

LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics
LM2904YDT

LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics

The STMicroelectronics LM2904YDT is a low-power dual operational amplifier with two independent amplifiers, a 30 V family voltage rating, a 0.6 V/µs slew rate, and an 8-pin SOIC package. It is intended for general-purpose signal-conditioning applications where two amplifier channels, low power consumption, and a tolerant supply-voltage range provide a practical combination of capability and board economy. An operational amplifier, or op amp, is a voltage-gain device used to amplify small input signals in analog signal chains. The LM2904 family belongs to the broader hierarchy of analog integrated circuits, signal amplifiers, operational amplifiers, and general-purpose amplifiers. Its differential inputs and single-ended outputs allow each channel to support common tasks such as buffering, gain amplification, voltage comparison, filtering, and instrumentation-style signal conditioning. The LM2904YDT provides two amplifier circuits in one 8-SOIC package. Its stated 30 V family rating supports operation from single-supply industrial signal-conditioning circuits, while the low-power architecture suits battery-powered and portable equipment. The 0.6 V/µs slew rate provides a concrete indication of how quickly the output can follow a changing input, making the device appropriate for low-to-moderate-bandwidth applications rather than high-speed signal paths. STMicroelectronics describes the LM2904 family as a low-power dual operational amplifier. The automotive-oriented Y suffix and automotive-grade classification make the LM2904YDT relevant to vehicle electronics, industrial controls, and other systems that require a dual amplifier in a compact surface-mount package. Because the package contains two channels, PCB area and component count can be reduced compared with separate single-channel amplifiers. Typical uses include low-frequency sensor conditioning, current-loop signal amplification, audio preamplification, active filtering, voltage buffering, and general industrial control. The device is also suitable for split-supply circuits when the signal can remain within the input and output common-mode limits specified by the manufacturer datasheet. Applications requiring wide bandwidth, rail-to-rail input or output operation, very low offset voltage, or low-noise performance should compare the LM2904YDT with precision or rail-to-rail amplifier families before finalizing the design. Designers should verify input common-mode range, output swing, output-current capability, and stability with the external compensation network for each specific operating point. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid using the amplifier outside its stated supply and common-mode limits. A bypass capacitor near each device helps control supply-line noise on shared analog boards. This product page combines the LM2904YDT operating identity with package, application, drop-in replacement, and design guidance. It highlights where the conventional low-power dual op amp is appropriate and where precision, speed, or rail-to-rail characteristics may justify a different amplifier architecture.

RFQ İletişim
LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904YPT

LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics

STMicroelectronics LM2904YPT is a low-power dual operational amplifier in an 8-TSSOP package, providing two independent general-purpose amplifier channels with single-ended outputs. The device is specified for 100 dB of open-loop voltage gain and 1.1 MHz of gain-bandwidth product, making it appropriate for signal-conditioning stages that require stable operation from low-frequency instrumentation through audio-range circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family, combining two amplifier channels in one package. Within the broader hierarchy, it is a low-power bipolar operational amplifier, a general-purpose amplifier IC, and a component within the wider analog signal-processing and semiconductor product category. The LM2904YPT's two channels can be configured independently as inverting amplifiers, non-inverting amplifiers, comparators, buffers, or differential amplifier stages. Its 100 dB open-loop gain supports accurate signal amplification when closed-loop feedback controls the operating gain. The 1.1 MHz gain-bandwidth product establishes the bandwidth available for closed-loop operation, while the low-power characterization supports economical designs where amplifier power consumption is an important system constraint. This dual architecture reduces component count and PCB area when a board requires two amplifier functions. It is particularly useful in sensor interfaces, analog signal conditioning, active filters, low-level audio paths, and general industrial control circuits. Because both channels share one package, designers should also evaluate common thermal and supply conditions rather than treating the two amplifier sections as completely independent systems. Typical circuit implementation uses conventional negative feedback, input bias-current compensation where required, and suitable decoupling near the supply pins. Input and output signal levels must remain compatible with the device's operating limits, while stable feedback and suitable output loading are necessary to maintain expected performance. Signal-routing practices should minimize coupling between the high-gain inputs and nearby switching or digital nodes. This page combines the exact LM2904YPT configuration, verified distributor listings, drop-in replacement analysis, package-level pin information, and practical design guidance. It helps engineers narrow the selection before requesting a quote for the dual low-power operational amplifier in its compact 8-TSSOP package.

RFQ İletişim
LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics
LM2904YST

LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics

The STMicroelectronics LM2904YST is a dual, low-power bipolar operational amplifier designed for general-purpose signal conditioning. The device provides two independent amplifier channels in an 8-pin MiniSO package and is specified for supply voltages up to 30 V, including operation from ±15 V rails. Its low-power design, broad input-voltage capability, and single-ended outputs make it suitable for industrial control, sensor interfaces, audio stages, and general analog signal-processing circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two such amplifier sections, allowing one package to process two related signals or to implement two stages of a larger circuit. As a bipolar operational amplifier, it provides input bias-current behavior and voltage-noise characteristics suited to many low-cost precision and control applications rather than the very low input bias current associated with CMOS or JFET input devices. The LM2904YST supports operation across a wide supply range and can operate with dual supplies such as ±15 V. The 30 V maximum supply rating provides useful headroom for industrial applications, while the low-power operating-current target reduces heat generation in battery- and line-powered equipment. Each channel uses a differential input arrangement and provides a single-ended output referenced to the negative supply rail. Common applications include buffering sensors, amplifying low-level control signals, and driving external circuitry within the amplifier’s output-current capability. The 8-MiniSO package is a compact surface-mount form factor that reduces board space compared with traditional through-hole SOIC packages. The YST ordering suffix identifies the tape-and-reel presentation, allowing the amplifier to be assembled through standard surface-mount production processes. Because operational-amplifier performance depends on surrounding passives and layout, input and feedback components should be positioned close to the relevant pins, while adequate supply bypassing should be placed directly across the device’s supply terminals. LM2904YST is appropriate for industrial instrumentation, feedback-control loops, transducer amplification, audio preamplification, and low-frequency analog filters. The dual-channel arrangement can reduce component count in designs using two separate gain stages. In designs requiring input offset current below the LM2904’s range, rail-to-rail precision, or operation from a single low-voltage supply, a CMOS-input amplifier may offer a better technical match even if it shares a similar package. Designers should verify input and output voltage limits at the selected supply voltage, confirm the required gain bandwidth and slew rate, and check that the planned load does not exceed the output-current capability. Input common-mode range, output swing, electrical-noise limits, and thermal performance should be checked against the worst-case operating conditions. Decoupling capacitors should be selected according to the manufacturer’s recommended application circuit and stability requirements. This product overview combines the manufacturer-distinguished LM2904YST configuration with package, application, cross-reference, and design-placement guidance. It supports faster component identification while emphasizing the distinctions engineers must validate before approving any analog signal-chain design.

RFQ İletişim
LM2924M Low-Power Op Amp/Comparator | Texas Instruments
LM2924M

LM2924M Low-Power Op Amp/Comparator | Texas Instruments

Texas Instruments LM2924M is a low-power dual-purpose analog IC containing two independent building blocks: a high-gain, internally frequency-compensated operational amplifier and a precision voltage comparator. The device is packaged in an 8-pin SOIC and is identified as an industrial-temperature-grade component. This combination allows one package to provide signal amplification and threshold detection without using separate amplifier and comparator packages. An operational amplifier is a voltage amplifier whose closed-loop gain is established by an external feedback network. A voltage comparator compares two input voltages and switches its output according to their relationship. The LM2924M combines these complementary functions in a single analog device, placing it in the operational-amplifier and comparator hierarchy while supporting transducer, sensing, control, and signal-conditioning applications. The internally frequency-compensated operational amplifier is designed to operate without an external compensation capacitor, simplifying implementation in basic gain configurations. Its comparator section provides an independent decision-making channel, allowing the two internal circuits to monitor or condition separate signals simultaneously. Because the amplifier and comparator are independent building blocks, their inputs and outputs can be used for different stages of a system. The National Semiconductor datasheet describes the LM2924M as a low-power operational amplifier and voltage comparator for precision voltage-amplification and related analog signal-processing needs. The 8-pin SOIC package provides a compact surface-mount format for industrial equipment, embedded controls, instrumentation interfaces, and mixed analog-digital circuit boards. Typical applications include transducers whose weak outputs require voltage amplification, sensor interfaces requiring a defined switching threshold, industrial control loops, and analog monitoring subsystems. The dual internal architecture can reduce board area when a design needs both continuous analog amplification and discrete threshold detection. For PCB implementation, assign the supply, ground, input, and output pins according to the manufacturer pin-description table and preserve the recommended input/output operating conditions. Confirm signal ranges, output states, stability requirements, and temperature limits against the device datasheet before connecting external transducers or logic interfaces. This page combines the device architecture, package details, sourcing guidance, verified replacement constraints, and practical application guidance. It also distinguishes confirmed drop-in choices from merely similar amplifier or comparator products, helping engineers avoid replacements that require PCB changes or behavioral redesign.

RFQ İletişim
LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments
LM2924MX

LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments

Texas Instruments LM2924MX is a low-power bipolar analog IC that combines an operational-amplifier function with voltage-comparator operation in an 8-pin SOIC package. It is identified as a single-function transducer-amplifier circuit, is designed for industrial-temperature use, and is supplied in a rectangular surface-mount SOP package. The LM2924MX therefore serves as a compact analog signal-conditioning component for systems that require amplification and threshold detection in one package. An operational amplifier is a voltage-controlled analog amplifier whose open-loop gain is made large enough to amplify small signals accurately when negative feedback is applied. A voltage comparator compares one input voltage with another and changes its output state when a threshold is crossed. Together, these functions form part of the broader linear and mixed-signal IC hierarchy, where they support sensor conditioning, control loops, signal detection, and industrial interface circuits. The LM2924MX combines three notable product attributes. First, its bipolar construction places it in the classical family of analog amplifier ICs. Second, its single-function analog-circuit architecture supports compact implementation of transducer and signal-conditioning paths. Third, the 8-pin surface-mount SOIC package permits automated assembly while reducing board area compared with larger through-hole packages. Its industrial temperature grade also positions it for equipment operating beyond typical commercial-temperature conditions. LM2924MX is identified as a low-power operational amplifier and voltage comparator. This dual operating role allows the same device to amplify a low-level analog signal and evaluate whether that signal has crossed a defined reference level. In feedback-based configurations, the amplifier behavior supports closed-loop gain; in open-loop threshold service, the comparator behavior provides a digital indication of an analog condition. Exact gain-bandwidth, input-offset, supply-voltage, and output-current limits should be confirmed from the manufacturer datasheet before final circuit sizing. Typical uses include bridge or resistive-transducer signal conditioning, industrial sensor interfaces, low-level control-signal amplification, threshold detection, and alarm-generation circuits. The 8-pin SOIC footprint is suitable for compact analog boards where a surface-mount part is preferred and where signal conditioning must be placed close to the sensor or source to minimize susceptibility to interference. Designers should determine the allowable supply range, input common-mode range, output swing, input-offset voltage, noise, and comparator propagation behavior from the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while sensitive input routing should avoid switching nodes and high-current return paths. Feedback resistors and any hysteresis network must be evaluated for the required gain, offset, and threshold stability. This product page consolidates the exact package, temperature-grade, circuit-type, and lifecycle information for LM2924MX, maps suitable analog applications, and provides engineering guidance for layout, compensation, and sourcing. It also distinguishes confirmed drop-in replacements from merely similar amplifier or comparator families so that PCB reuse decisions remain technically defensible.

RFQ İletişim
LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments
LM293AD

LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments

Texas Instruments LM293AD is an industrial-grade dual differential comparator with two independent comparison channels, a 2 V to 36 V supply range, rail-to-rail input operation, and open-collector/open-drain outputs. The device is packaged in an 8-pin SOIC and is designed for sensing and control applications involving wide input and output voltage conditions. A differential comparator is an integrated circuit that compares two input voltages and changes its output state according to their relationship. Its two channels can monitor thresholds, detect crossings, implement window functions, or generate control signals. The LM293 belongs to the comparator hierarchy within analog interface ICs, where it bridges analog sensing and digital control logic. The LM293AD operates from 2 V to 36 V and provides a response time of approximately 300 ns. Its common-mode input range includes ground, and its differential input range can equal the maximum-rated supply voltage of ±38 V according to the manufacturer product information. Open-collector outputs support wired logic, pull-up arrangements, level translation, and compatibility with TTL, MOS, and CMOS systems. Each comparator section compares an inverting input with a non-inverting input. When the non-inverting input is higher, the corresponding open-collector output transistor turns off; when the inverting input is higher, the output transistor turns on. An external pull-up resistor is required for conventional open-collector operation. The two channels share the supply pins but retain separate input and output pins. Typical uses include industrial sensor interfaces, battery monitoring, power-supply fault detection, overvoltage protection, relay or LED indication, and control systems that compare an analog voltage against a reference. The wide operating supply range is useful when the comparator must tolerate industrial transients while operating from a higher-voltage rail. Designers should verify input and output absolute maximum ratings, provide adequate pull-up resistors, maintain a valid common-mode range, and account for output-current limits when several wired-open-collector outputs share a bus. Because the outputs can sink current but cannot source it independently, external pull-ups determine the high logic voltage and rise-time behavior. This product page combines manufacturer specifications, verified distributor listings, same-package replacement guidance, and practical comparator-design notes. It helps engineers evaluate the LM293AD for industrial threshold detection, protection, monitoring, and open-collector interface designs without confusing it with open-drain parts that use different output structures.

RFQ İletişim
LM293ADR - 36 V Dual Comparator | Texas Instruments
LM293ADR

LM293ADR - 36 V Dual Comparator | Texas Instruments

The Texas Instruments LM293ADR is a dual differential comparator designed for industrial applications, with two comparator channels, a 2 V to 36 V supply range, and an 8-pin SOIC package. The device supports open-collector and open-drain outputs and is specified for an extended temperature range of -25°C to +85°C. According to the manufacturer product page, its common-mode input voltage range includes ground, making it suitable for sensing signals close to the lower supply rail. A differential comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The LM293 belongs to the comparator hierarchy within interface ICs, where analog input conditioning is converted into a logic-compatible decision. Its open-collector output allows the output state to be defined by an external pull-up resistor, making the device useful in wired-logic, relay-driving, and open-drain bus interfaces. The LM293ADR provides several characteristics suited to robust circuit design. Its 36 V maximum supply permits operation in industrial environments, while its rail-to-rail input capability allows comparisons near ground. The manufacturer identifies the output as compatible with TTL, MOS, and CMOS logic. The differential input voltage range can equal the maximum-rated supply voltage, and the device is specified for operation over a 2 V to 36 V total supply range. The LM293A family uses two independent comparator sections within one package. Each section has inverting and non-inverting inputs, an output, and shared supply connections. The open-collector architecture requires a pull-up resistor when the output must actively drive high. The result is a flexible interface between high-voltage or low-level analog signals and digital control logic without requiring a rail-to-rail push-pull output stage. Typical applications include overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control interfaces, relay or solenoid drivers, window or level comparators, and open-drain bus signaling. The dual-channel configuration allows two related threshold decisions to be implemented in one package, reducing board area when both channels operate from the same supply. When designing the circuit, choose the pull-up resistor for the required sink current and logic level, and verify that all input pins remain within the common-mode range at every supply condition. Because the output is open-collector, a floating output can occur without a pull-up. Confirm timing against the application’s threshold-crossing rate and maintain adequate supply decoupling close to the power pin. This page combines the manufacturer’s electrical and ordering information with package guidance, comparison criteria, sourcing support, and practical application notes to help engineers evaluate the LM293ADR for new and existing comparator designs.

RFQ İletişim
LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi
LM293AM

LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi

The onsemi LM293AM is a dual differential comparator designed for single-supply operation up to 36 V or dual-supply operation up to ±18 V, and it is available in an 8-pin SOIC package. Its differential inputs allow two voltages to be compared, while the open-collector output structure supports flexible interface and pull-up arrangements in control, sensing, and protection circuits. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual configuration provides two independent comparators in one package. When used with an external pull-up, an open-collector output can drive TTL, MOS, or CMOS-compatible circuitry while also allowing wired logic, level translation, or system reset behavior. The LM293AM belongs to the comparator hierarchy within amplifier and interface ICs. Key features include single-supply operation to 36 V, dual-supply operation to ±18 V, a typical low-current drain of 800 µA, and a typical input bias current of 25 nA. The device can compare input voltages near ground potential and is compatible with multiple logic families. Its low input bias current helps reduce source-loading effects in high-impedance sensing networks, while the wide supply range supports industrial and automotive-style control environments. The LM293AM uses open-collector outputs rather than push-pull outputs. This architecture provides a useful advantage when a comparator output must remain inactive until an external pull-up supplies the required logic-high voltage. It also supports open-wired signal arrangements, but every application must include the appropriate pull-up resistor and verify that the resulting rise time is acceptable. The operating common-mode range, differential input limits, output sink capability, and timing behavior should be checked against the manufacturer datasheet for the selected manufacturer version. Typical applications include industrial control systems, power-supply supervision, motor and solenoid protection, battery monitoring, sensor-threshold conditioning, window or level detection, and general-purpose logic interfaces. The dual comparator arrangement is particularly useful when one circuit monitors two related thresholds or when an enable function and a fault signal can be implemented with the two channels in a compact footprint. For PCB design, place the device so that sensitive input traces remain away from switching nodes and output pull-up routing. Keep input and output paths separate to reduce feedback through supply or board-level coupling. Confirm the logic-high level, output rise time, input common-mode range, supply decoupling requirements, and operating temperature range before releasing the design for production. This page combines manufacturer-family operating limits, package details, sourcing guidance, replacement analysis, and practical PCB considerations to support faster component selection. Review the complete pin assignment and electrical characteristics in the LM293AM datasheet before layout, particularly when the same circuit must accommodate multiple LM293-family variants.

RFQ İletişim
LM293AN - Dual Open-Collector Comparator | STMicroelectronics
LM293AN

LM293AN - Dual Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM293AN is a low-power dual voltage comparator with two independent comparator channels, open-collector and open-drain outputs, and an 8-DIP package. The device is designed for general-purpose signal comparison and can operate from a single supply over a wide voltage range, while split-supply operation is also possible. Its listed rail-to-rail input designation, ground-referenced common-mode capability, and TTL, MOS, and CMOS output compatibility make it suitable for threshold detection, level translation, and analog-control systems. A voltage comparator is an integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. In this role, LM293AN belongs to the comparator IC hierarchy within analog and mixed-signal semiconductors. Each of its two channels can evaluate a non-inverting input against an inverting input, allowing one package to perform two related comparisons while keeping channel operation independent. The LM293 family documentation identifies low power consumption as a defining characteristic and specifies input-offset voltage as low as 2.0 mV maximum for the associated two-comparator family. Open-collector outputs provide flexibility when the destination device requires a pull-up resistor, particularly in wired logic, relay-driver, and legacy digital-interface applications. The outputs are also listed as compatible with TTL, MOS, and CMOS logic families. Operation from a single supply is central to the device design. The common-mode input range includes ground, while the differential input voltage can extend to the maximum-rated supply voltage of ±38 V according to TI's LM293 family information. The 8-DIP mechanical format provides through-hole access to the two comparator channels, power, ground, and output connections. Typical uses include industrial control thresholds, sensor-interface decisions, window comparators, oscillator and timer designs, and general logic level conditioning. The two independent channels can also implement a larger comparator arrangement through external resistor networks. Open-collector outputs make pull-up selection an important part of the interface design because the output cannot directly drive a logic high without this external support. The main design consideration is that open-collector outputs require correctly selected pull-up resistors and adequate logic-level rise time at the driven node. Supply decoupling, input-source impedance, output load, and common-mode headroom should be reviewed against the application's operating conditions. This page consolidates the verified device identity, package information, sourcing links, and practical comparator-selection guidance.

RFQ İletişim
LM293D - Dual Differential Comparator, 8-SOIC | TI
LM293D

LM293D - Dual Differential Comparator, 8-SOIC | TI

The Texas Instruments LM293D is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293D is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293D listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293D is not a power semiconductor, so SOA data is not applicable.

RFQ İletişim
LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi
LM293DG

LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi

The onsemi LM293DG is a dual independent precision voltage comparator in an 8-pin SOIC package, built for single or split supply operation across a 2 V to 36 V supply range. Each channel offers an input offset voltage as low as 2.0 mV, a 1.3 microsecond response time, and a supply current of about 400 microamps per channel, with an open-collector (open-drain) output stage compatible with TTL, MOS and CMOS logic. A comparator is a differential amplifier used as a simple decision element: it compares two input voltages and switches its output state when the non-inverting input rises above the inverting input. The comparator category sits above discrete transistor switches in the signal-conditioning hierarchy and below instrumentation amplifiers in the analog IC family, sitting in the amplifier IC / signal conditioning control group of parts such as op amps, references and sensor interface ICs. The LM293 series is distinguished from general-purpose comparators by its low input offset voltage, wide supply range and ability to operate with the common-mode input range extending to ground, which makes it a strong fit for single 5 V or single 12 V systems where the signal of interest lives near the negative rail. The two channels are fully independent, each with its own pair of inputs and output. The open-collector output stage is the key architectural feature: the output transistor sinks current but never sources it, so an external pull-up resistor to the supply or logic rail is required to establish a valid high level. That architecture permits level shifting to any voltage up to the maximum supply, wired-AND bus tying, and direct drive of relay or solenoid drivers without a buffer stage. Because the output stage is a bipolar NPN transistor, output sink current is limited compared with modern CMOS comparators. Typical applications include overvoltage and undervoltage protection in linear and switching power supplies, battery and pack monitoring window comparators, motor stall and over-current detection, industrial sensor thresholding, and automotive-style sensor protection. The SOIC-8 package with 1.27 mm lead pitch supports both through-hole assembly and standard surface mount reflow, and the -25 C to +85 C ambient range covers industrial and consumer equipment. When designing with the LM293DG, always fit a pull-up resistor on each output and check the sink current against the pull-up value and the load. If your design needs rail-to-rail input operation, push-pull outputs, or a supply below 2 V, a CMOS comparator is the better choice; if it needs low offset with wide supply and open-drain flexibility, the LM293DG remains a proven, low-cost choice. This page consolidates manufacturer specifications, drop-in replacement candidates, pin-level detail and practical design guidance so that you can qualify the LM293DG for an existing board revision without redrawing the footprint.

RFQ İletişim
LM293DGKR - Dual 2-36V Comparator | Texas Instruments
LM293DGKR

LM293DGKR - Dual 2-36V Comparator | Texas Instruments

The Texas Instruments LM293DGKR is a dual differential comparator with two independent comparator channels, a 2 V to 36 V supply range, and a 300 ns response time, housed in an 8-pin VSSOP package. Each channel uses open-collector output architecture, making the device suitable for wired logic interfaces, threshold detection, and systems requiring a pull-up resistor. A differential comparator is an analog integrated circuit that compares two input voltages and produces a binary output indicating which input is higher. The LM293 belongs to the voltage-comparator hierarchy within interface and signal-conditioning semiconductors. Its two channels can operate independently, allowing one package to perform two comparison functions while reducing board area and simplifying component procurement. The principal operating characteristics include a 2 V to 36 V supply range, a 300 ns response time, and approximately 200 uA supply current. The open-collector outputs can sink useful levels of output current while the external pull-up resistor determines the high output voltage. Rail-to-rail input operation is identified for this device, while its industrial operating range of -40 C to +85 C supports laboratory, control-system, and industrial equipment. Each internal channel compares its noninverting and inverting inputs. Because the outputs are open collector, both channels can be tied together when wired-OR logic is required. The low output saturation behavior also permits direct interfacing with TTL, MOS, and CMOS-compatible external circuitry. Separate ground, supply, input, and output connections make the device straightforward to use in both single-supply and split-supply arrangements, subject to the applicable input limits. Typical uses include power-rail monitoring, industrial sensor threshold detection, battery and charger supervision, window-comparator circuits, control-loop signal conditioning, and logic-level translation where an open-drain interface is advantageous. The dual-channel configuration is particularly useful when a design requires two related decisions, such as an upper threshold and a lower threshold around the same monitored quantity. Designers should select an external pull-up resistor for each open-collector output and confirm that its resistance keeps output rise time and sink current within system requirements. Input and supply connections should be kept short, with suitable local bypassing placed close to the device. Thermal and common-mode limits must be checked across the full operating range, especially in industrial systems with long wiring and noisy power sources. This product overview combines the LM293 family identity, verified package and ordering information, practical comparator design guidance, drop-in family alternatives, and a specification comparison intended to accelerate component selection and PCB planning.

RFQ İletişim
LM293DMR2 - Dual Precision Comparator, 36 V | onsemi
LM293DMR2

LM293DMR2 - Dual Precision Comparator, 36 V | onsemi

The onsemi LM293DMR2 is a dual low-offset voltage comparator with two independent comparison channels, a 2 V to 36 V supply range, open-collector outputs, and an 8-pin TSSOP package. Each channel can operate from single or split power supplies, allowing common-mode input signals to approach ground during single-supply operation. The low input offset voltage, specified as low as 2.0 mV, supports accurate threshold detection in industrial, automotive, and consumer circuits. A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital logic state at its output. The LM293 belongs to the comparator hierarchy, which includes differential comparators, window comparators, and precision comparators. By converting an analog threshold relationship into an open-collector logic indication, this type of device bridges analog measurement circuits and digital control, monitoring, or protection systems. The principal features include two independent comparators, low offset voltage, a common-mode input range extending to ground under single-supply operation, and open-collector outputs that can sink current from multiple compatible devices. The 2 V to 36 V operating supply range accommodates 5 V, 12 V, and 24 V systems. The onsemi datasheet also identifies the device as suitable for consumer, automotive, and industrial applications where reliable voltage-level detection is required. Each comparator channel is independent, allowing one device to perform two unrelated threshold measurements. The open-collector architecture requires an external pull-up resistor and provides a wired-output capability when several comparator outputs share a bus. This architecture does not actively drive the output high, but it offers flexible voltage-level adaptation and enables wired-AND behavior when output collectors are connected. Typical uses include monitoring a 12 V or 24 V automotive battery, detecting overvoltage and undervoltage conditions in industrial power systems, comparing sensor outputs with adjustable thresholds, and providing simple supervisory functions in consumer equipment. The grounded common-mode capability is especially useful in single-supply systems where the signal of interest begins near 0 V and cannot be compared reliably by a comparator with a restricted input range. For robust PCB implementation, place input resistors close to the comparator pins to limit differential pickup and route the inputs away from switching nodes and high-current paths. Select the external output pull-up for the intended logic voltage, and confirm that its maximum sink current remains within the device output ratings. Check that the common-mode and differential input voltages remain within the absolute maximum limits during power transients. This product page combines the manufacturer specifications, package and pin information, drop-in replacement analysis, comparison data, and practical PCB guidance to accelerate design review and sourcing. The technical recommendations focus on preserving the LM293DMR2 role as a reliable, low-offset dual comparator while making package, electrical, and supply constraints explicit before layout release.

RFQ İletişim
LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)
LM293DR

LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)

The Texas Instruments LM293DR is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293DR is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293DR listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293DR is not a power semiconductor, so SOA data is not applicable.

RFQ İletişim
LM293DR2G - Dual 36V Comparator | onsemi | Signal Control
LM293DR2G

LM293DR2G - Dual 36V Comparator | onsemi | Signal Control

The onsemi LM293DR2G is a dual precision voltage comparator rated for 2 V to 36 V operation, with a 1.3 µs response time and open-collector, open-drain outputs in an 8-pin SOIC package. The device contains two independent comparator channels and can operate from a single supply or split supplies, making it suitable for industrial threshold detection, sensing, and control circuits. A voltage comparator is an analog signal-conditioning device that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. Within the broader hierarchy of semiconductor components, the LM293DR2G belongs to the comparator category, analog signal-conditioning ICs, and power-management-adjacent control devices. Its two independent channels allow one package to perform two comparisons while sharing a common supply and ground. The principal operating characteristics include a 2 V to 36 V supply range, a 1.3 µs response time, and a dual open-collector output architecture. The output structure can sink useful load current and requires an appropriate pull-up arrangement when driving subsequent digital stages. According to the onsemi LM293 family information, input offset voltage can be as low as 2.0 mV, while the LM293 series is designed for common-mode input operation down to ground with single-supply operation. Each internal channel has differential inputs and an independently controlled output. Separate inputs allow the circuit designer to define the polarity of each decision, while separate output stages provide isolation between the two comparator functions. The 8-pin SOIC package supports conventional surface-mount assembly, but exposed-pad thermal management is not part of this package. Exact offset-voltage limits, input bias current, output-current limits, and channel-matching figures should be selected from the ordering information for the exact grade. Typical uses include industrial sensor thresholds, motor and actuator control, power-supply monitoring, window or level detection, and general signal conditioning. In these systems, the comparator converts an analog relationship between two voltages into a logic-compatible indication that downstream control logic can process. The 36 V maximum supply capability is especially useful when the sensing circuit operates from an industrial bus rather than a low-voltage logic rail. For dependable operation, treat each open-drain output as requiring a pull-up to the supply used by the receiving logic. Keep input and feedback traces short, provide a local supply bypass capacitor, and confirm that input voltages remain within the applicable common-mode and absolute-maximum limits. Account for output rise time after the pull-up resistor is added because the stated 1.3 µs response describes comparator propagation behavior, not the complete RC-controlled transition at the output node. This product record combines the manufacturer family description with package, supply, temperature, and response-time details, then adds application guidance, pin-level implementation notes, and same-footprint comparison choices. These engineering views help designers evaluate the LM293DR2G as a dual comparator rather than treating it only as an eight-pin logic IC.

RFQ İletişim
LM293DRE4 Dual Differential Comparator 36V | Texas Instruments
LM293DRE4

LM293DRE4 Dual Differential Comparator 36V | Texas Instruments

The Texas Instruments LM293DRE4 is a dual differential comparator IC designed for single-supply or split-supply operation, with a maximum tested supply voltage of 36 V and an 8-SOIC package. The device contains two independent comparators with open-collector, open-drain outputs, allowing the output state to be pulled up externally. Its wide supply-voltage range, low supply-current drain of approximately 0.4 mA per comparator, and input common-mode range that includes ground make it suitable for industrial voltage-threshold, sensing, and control applications. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM293 belongs to the comparator category within analog signal-chain and power-management ICs, rather than acting as an amplifier or regulator. Two comparators in one package provide independent channels for monitoring two thresholds, controlling two loads, or implementing a window-detection function. The open-collector outputs are useful for wired logic, relay-driver interfaces, and systems requiring a pull-up resistor. The main electrical characteristics include operation from a single supply or dual supplies, a 2 V to 36 V difference between supply rails, a common-mode input voltage range that includes ground, and low output saturation voltage. The LM293 is specified as compatible with TTL, MOS, and CMOS logic levels. The output structure can sink current from an external pull-up while providing a predictable low-level output, allowing designers to select the pull-up voltage independently of the comparator supply. The LM293 architecture is based on two independent comparator channels rather than a shared output. This arrangement allows each channel to use separate non-inverting and inverting inputs while sharing the device supply pins. The inputs are intended for low-power threshold sensing, and the operating range supports both traditional positive-supply circuits and circuits using ground as the lower input reference. Open-collector outputs require an external pull-up when a valid high output is required. Typical applications include industrial process-limit detection, battery and power-supply monitoring, sensor signal conditioning, overvoltage and undervoltage protection, relay or solenoid control interfaces, and window comparators. The comparator can also be used as a simple line-driver or discrete-amplifier element in low-frequency control circuits. Because the output is open collector, the pull-up resistor and load current must be selected to match the desired logic voltage and switching speed. For PCB design, place the decoupling capacitor close to the supply and ground pins, and route comparator inputs away from switching nodes and high-current paths. The 8-SOIC footprint allows straightforward through-hole assembly and rework. The pull-up resistor should connect from each output to the logic rail used by the receiving device. Confirm the input voltages, supply current, output sink current, and common-mode limits against the application before releasing the design. This product page combines the manufacturer’s LM293 family information, exact-MPN sourcing details, pin-level integration guidance, and drop-in replacement analysis. It is intended to help engineers move from component identification to schematic review, footprint verification, and robust analog threshold-circuit design.

RFQ İletişim
LM293DRG3 - Dual Differential Comparator | Texas Instruments
LM293DRG3

LM293DRG3 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM293DRG3 is a dual differential voltage comparator in an 8-pin SOIC package. The device contains two independent comparison channels, supports ±15 V single-ended or 30 V total supply operation, and provides open-collector, open-drain outputs compatible with TTL, MOS, and CMOS logic. Its common-mode input range includes ground, allowing operation from a single positive supply, while the differential input range can extend to ±38 V. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM293 belongs to the comparator hierarchy, which also includes differential comparators and open-collector interface comparators. These devices bridge low-level analog sensing and digital control by converting an analog condition into a logic-readable result. The LM293DRG3 offers two independent comparators, rail-to-rail output behavior, and low output saturation voltage. Its open-collector outputs permit wired-AND connections and external pull-up selection, making the device adaptable to different logic families and voltage domains. The common-mode input range including ground is particularly useful in battery-powered and industrial systems powered from a single rail. Each channel compares a non-inverting input with an inverting input and uses open-drain output transistors to indicate the polarity of the differential voltage. The outputs can sink current while remaining in a high-impedance state when inactive. Because the output stage does not actively drive a high voltage, pull-up resistors are required when a logic-high level is needed. Differential input protection and common-mode limits must be respected during fault conditions. Typical uses include monitoring a sensor output, detecting supply thresholds, comparing an analog measurement with a reference, generating window-limit signals, and supporting industrial control logic. Two independent channels allow related threshold functions to be implemented in one package, reducing component count while preserving separate input and output isolation. Designers should select pull-up resistors to suit the destination logic voltage and sink-current budget, connect an unused comparator input to a defined valid potential, and verify input and output behavior across the full supply range. This page combines ordering information, package details, drop-in replacement guidance, comparison data, and practical design guidance for faster component selection.

RFQ İletişim
LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments
LM293DRG4

LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM293DRG4 is a dual differential comparator with two independent channels, open-collector outputs, and an 8-pin SOIC package. It supports single-supply operation over a wide voltage range and dual-supply operation when the total supply difference is between 2 V and 36 V. Each channel compares an inverting input with a non-inverting input and provides a logic-compatible indication of the input relationship. A comparator is an analog integrated circuit that evaluates two voltages and changes its output state when one input crosses the other. Within the signal-chain hierarchy, the LM293 belongs to the comparator class, which sits alongside amplifiers and other analog interface ICs used to convert continuous voltage relationships into binary logic decisions. The LM293's open-collector outputs are useful when a system needs a pulled-up logic signal, wired logic, level translation, or an adjustable output rise time. The LM293 family is specified as a dual differential comparator for industrial applications. The LM293DRG4 ordering code identifies the 8-SOIC package and tape-and-reel shipping configuration. Its two channels are independent, allowing one device to implement two threshold decisions. Open-collector outputs also permit multiple devices to share a common pull-up bus when the system designer confirms that the resulting wired-AND behavior is intentional. The device can operate from a single supply or from positive and negative supplies. The manufacturer states that the common-mode input range includes ground, that the differential input range equals the maximum-rated supply voltage, and that the output is compatible with TTL, MOS, and CMOS logic. The LM293B version is identified as a drop-in replacement for LM293, LM393, and LM2903 families, providing a useful basis for qualified equivalent selection. Typical applications include power-supply threshold detection, sensor-signal conditioning, industrial control interfaces, battery monitoring, and digital logic level translation. In a sensor interface, the non-inverting input can receive a reference voltage while the inverting input receives the sensed signal, allowing the open-collector output to indicate when the signal crosses the selected threshold. The output requires an external pull-up because the LM293 does not actively drive its output high. Designers should account for input offset voltage, common-mode limits, supply voltage, output pull-up resistance, and propagation delay. Input components should also prevent excessive differential input voltage and protect sensitive sensor nodes from electrostatic discharge. Because the output is open collector, the pull-up resistor and its placement materially affect rise time, power consumption, and susceptibility to interference. This page combines the LM293 family architecture, verified ordering and package information, practical replacement criteria, threshold-comparison guidance, and PCB-focused design considerations. It also distinguishes genuine pin-compatible choices from options that require changes to output pull-ups, supply arrangements, or board layout.

RFQ İletişim
LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics
LM293DT

LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics

STMicroelectronics LM293DT is a low-power dual voltage comparator containing two independent comparator channels in an 8-pin SOIC package. Each channel supports a single supply from 2 V to 36 V or dual-supply operation, while the input stage accepts input voltages spanning the supply rails. The device uses open-collector output stages suitable for driving wired-AND, open-drain, and pull-up-based interfaces. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used between sensors, amplifiers, reference voltages, and digital control logic. Its two independent channels allow one package to perform two threshold decisions, reducing component count in industrial controls, monitoring equipment, and embedded systems. Key characteristics include very low supply current of 0.4 mA typical, 1 mW power consumption per comparator at a 5 V supply, low typical input bias current of 25 nA, and typical input offset current of ±5 nA. The typical input offset voltage is ±1 mV. Rail-to-rail input capability allows each comparator to operate with inputs near the negative and positive supply limits, while the open-collector outputs require an external pull-up resistor. The LM293DT uses a bipolar comparator architecture optimized for low power rather than high-speed operation. Its low input currents are useful when the source impedance is high or leakage would otherwise shift the comparison threshold. Because the outputs are open collector, two or more outputs can share a pull-up node to form a wired-AND function. The external pull-up determines output rise time, so resistance and capacitance must be selected together for the required switching speed. Typical applications include battery-powered threshold detection, sensor-signal conditioning, window comparators, overvoltage monitoring, industrial control interfaces, and simple switching regulators. The dual configuration is particularly useful when a system must monitor two independent limits or compare a measurement against both an upper and lower reference. For reliable PCB operation, place input and output bypass capacitors close to their associated pins and route comparator inputs away from switching nodes and high-current return paths. Account for input offset voltage and common-mode limits when defining detection thresholds. The open-collector outputs must always have a pull-up unless the output is intentionally left unconnected. This product page combines operating characteristics, application guidance, package information, and same-footprint replacement context to support faster component selection and board-level implementation.

RFQ İletişim
LM293H - Dual Differential Comparator | Texas Instruments
LM293H

LM293H - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM293H is a dual differential comparator, an analog comparator IC with two independent comparison channels, open-collector outputs, and a TO-99-8 metal can package. The verified product data identifies the device as a general-purpose, low-power comparator with low offset voltage, operating from single or dual supplies over a wide voltage range. The LM293H is suitable when two signals must be compared and the result must drive TTL, MOS, CMOS, or other digital logic through its open-collector output. A differential comparator is a semiconductor device that compares two input voltages and produces a logic-level indication of their relationship. The dual-channel architecture provides two independent comparators in one package, reducing component count in threshold detection, overvoltage indication, current sensing, and control systems. Its open-collector outputs require an external pull-up resistor when the output must settle to a valid high level. The LM293 family is associated with wide supply capability, single-supply operation, and compatibility with common logic families. The LM293H is identified in the verified distributor data as an 8-pin TO-99-8 device with two channels. The manufacturer family information describes the LM293 as an industrial-grade dual differential comparator. The verified search data specifically lists low power, low offset voltage, rail-to-rail input labeling, open-collector output, and a wide supply operating range. Detailed electrical limits, propagation-delay curves, input common-mode limits, output sink-current limits, and temperature limits must be confirmed in the manufacturer datasheet before final design release. Typical uses include battery-powered monitoring, industrial sensor interfaces, overvoltage detection, temperature threshold circuits, and dual-rail control logic. In a practical design, each comparator can monitor a signal against a reference voltage while the open-collector output drives a pull-up and the downstream logic input. Care is required when inputs approach supply rails, when output pull-up speed affects timing, or when unused comparator channels are left unconnected. This page combines verified manufacturer and distributor links, package identification, application guidance, and structured comparison information. It intentionally avoids filling unavailable electrical values with guesses; consult the current manufacturer datasheet for authoritative limits, ordering details, and lifecycle information.

RFQ İletişim
LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics
LM293N

LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics LM293N is a dual, general-purpose voltage comparator with two independent channels, open-collector outputs, and an 8-DIP package. According to the STMicroelectronics LM293N product description, it is designed for single-supply operation across a wide voltage range, while operation from split power supplies is also possible. The verified distributor listing identifies the device as an 8-DIP comparator with open-collector/open-drain, rail-to-rail characteristics. Specific voltage, current, timing, temperature, and logic-threshold values were not included in the provided data and therefore require verification from the manufacturer datasheet before design release. A voltage comparator is an analog semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM293N contains two independent comparators, allowing one package to implement threshold detection, window comparison, free-running oscillator, or simple analog-to-logic conversion. Within the broader hierarchy, it is a comparator IC, then an analog integrated circuit, and finally a semiconductor. Its open-collector outputs can sink external current and normally require a pull-up resistor when the design expects a high-level output. The primary documented feature is its ability to operate from a single supply over a wide range of voltages, with split-supply operation also supported. The two independent channels provide design flexibility for comparing a sensor against a reference, checking a power rail, or generating complementary decisions in control circuitry. The open-collector architecture can support wired logic and level translation, but the external pull-up, output current, propagation delay, and input common-mode limits must be checked against the actual datasheet. LM293N is suitable for industrial control, instrumentation, power-supply supervision, sensor interfaces, and embedded threshold detection. In a single-supply circuit, place the input network so that the signal remains within the device's verified common-mode range. In a split-supply circuit, confirm the positive and negative rail limits and the permitted total voltage. Because the provided data does not state absolute maximum ratings, supply voltage, input offset, output-current capability, response time, or operating temperature, those values should not be assumed. Design practice should include a local bypass capacitor, a defined pull-up resistor for each open-collector output, and protection for exposed sensor inputs. Avoid relying on an output high level until the pull-up network and downstream load have been analyzed. Verify input polarity, output inversion, hysteresis, and logic compatibility with the system controller. The 8-DIP package is mechanically important: use the manufacturer pinout and maintain adequate lead spacing during assembly. This page combines the verified LM293N product identity, package information, application context, datasheet links, and engineering considerations. It intentionally does not fabricate electrical ratings, pricing, lifecycle claims, or unreported pin names; obtain the current manufacturer datasheet and distributor quotation for production decisions.

RFQ İletişim
LM293P - Dual 36V Differential Comparator | Texas Instruments
LM293P

LM293P - Dual 36V Differential Comparator | Texas Instruments

Texas Instruments LM293P is a dual differential comparator rated for a 2 V to 36 V supply range, with a stated propagation delay of 300 ns, packaged as an 8-pin PDIP. Each channel provides independent differential inputs and an open-collector output, making the device suitable for threshold detection, level translation, relay driving, and industrial control logic. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LM293 belongs to the comparator hierarchy, which sits within linear and mixed-signal ICs. Its open-collector outputs can sink current from a pull-up network, allowing the outputs to be wired together when wired-OR operation is required. The principal features of the LM293P are its dual-channel architecture, differential input arrangement, wide 2 V to 36 V operating supply range, open-collector outputs, and 300 ns response time. The package is an 8-pin PDIP, providing a through-hole footprint suitable for prototypes, legacy industrial equipment, repair assemblies, and applications where leaded components are preferred. The LM293 contains two electrically independent comparator channels. Differential inputs are presented through inverting and non-inverting pins, while the output uses an open-collector transistor capable of pulling the output node toward ground. A pull-up resistor is required to establish a high output level, and the output stage can sink current from TTL, CMOS, and other logic families within the device's stated operating limits. Typical uses include monitoring a control or battery voltage against a reference, detecting sensor crossings, implementing overvoltage and undervoltage protection, driving relay or indicator circuits, and providing threshold-compatible interfaces between analog and digital systems. Because the device supports a wide supply range, it can also be used in industrial systems operating from conventional low-voltage DC rails. Designers must provide the required output pull-up and verify input common-mode limits, output-current limits, and operating temperature against the manufacturer datasheet. Input protection, bypassing, and leaded-component spacing should also be considered when the LM293P is used in high-noise or high-voltage surroundings. This page combines verified manufacturer and distributor information with package-level selection guidance, verified drop-in candidates, application use cases, and practical design notes. It is intended to help engineers identify whether the LM293P fits an existing 8-pin comparator design without confusing electrically related but mechanically different packages.

RFQ İletişim
LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics
LM293QT

LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics

The STMicroelectronics LM293QT is a dual general-purpose comparator designed for low-power operation from a single supply or split supplies. The device provides two independent comparator channels, a wide single-supply operating range of 2 V to 36 V, and an open-collector output configuration. It is packaged in an 8-UFDFN package with a 2 mm x 2 mm body size. The LM293QT is suited to voltage-level detection, threshold comparison, industrial control logic, sensor interfaces, and low-current signal conditioning where a compact, low-power comparator is required. An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state when the voltage at the non-inverting input becomes higher than the voltage at the inverting input. The LM293 family belongs to the comparator and linear IC hierarchy, where each independent channel compares its differential input while operating from a common supply. This makes the device useful between sensors and digital control systems, where a small voltage difference must be converted into a logic-compatible indication. The principal electrical characteristics include a 2 V to 36 V single-supply range, operation from split supplies of plus or minus 1 V to plus or minus 18 V, and very low supply current of approximately 0.45 mA. The comparator channels feature low input bias current of approximately 20 nA. The open-collector output stage allows the output to be pulled up to an external supply and enables wired-AND behavior when multiple comparator outputs are connected. The output type is suitable for interfacing with open-drain or open-collector digital devices. The LM293QT provides two independent channels in a compact 8-UFDFN package. The wide supply range allows operation from low-voltage systems through higher industrial rails, while the low supply current supports battery-operated and always-on equipment. The two channels can be used for independent threshold decisions, window monitoring, or complementary comparisons. Open-collector outputs require an external pull-up resistor when the output must rise to a defined logic-high voltage. Typical applications include industrial sensor interfaces, battery monitoring, power-supply sequencing, overvoltage and undervoltage detection, temperature-controller signal conditioning, and embedded threshold logic. Because the input common-mode range can include ground, the LM293QT is particularly useful in systems where the signal being monitored is close to the negative supply rail. When laying out a design, preserve the exposed-pad and package thermal requirements of the 8-UFDFN package. Route the comparator inputs away from switching nodes and high-current output paths, and place the input and output components close to their associated pins. Choose the external pull-up voltage and resistor to match the receiving logic, and verify that the output sink current remains within the device limits for the selected pull-up network.

RFQ İletişim
LM293ST - Dual 2V-36V Comparator | STMicroelectronics
LM293ST

LM293ST - Dual 2V-36V Comparator | STMicroelectronics

The STMicroelectronics LM293ST is a dual differential voltage comparator designed for low-voltage operation, with a 2 V to 36 V supply range and open-collector, open-drain outputs. The device contains two independent comparator channels in an 8-pin MiniSO surface-mount package, allowing both channels to operate from the same supply or from split power rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 family belongs to the comparator and amplifier IC category within the broader semiconductor hierarchy. Its open-collector outputs can sink current while remaining in a high-impedance state, making the device suitable for wired logic, pull-up resistor networks, relay drivers, and systems that require a flexible output drive configuration. The LM293ST provides two independent comparators, low offset, and high precision according to the STMicroelectronics LM293 family information. Its rail-to-rail input operation allows each differential input to approach the supply rails, which is useful when monitoring low-voltage sensor signals or battery-powered thresholds. The open-collector outputs also provide a deliberate isolation between the comparator output and the supply voltage, permitting external pull-up selection for a different logic family. Both channels can operate from a single 2 V to 36 V supply, and the device also supports split power-supply arrangements. The low-power architecture is intended for general-purpose threshold detection rather than high-speed signal conditioning. Because the outputs are open collector, designers must add pull-up resistors when a continuously driven high level is required. The output transistor provides current sinking capability, while the external pull-up establishes the high-state voltage and limits the available rise rate. Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, battery monitoring, window-comparator circuits, control-loop signaling, and digital interface adaptation. Two channels can also implement a hysteretic switching controller, an automatic window detector, or a pair of independent limit alarms. In each case, input and output implementation details should be checked against the operating voltage, common-mode range, load current, and logic requirements of the completed circuit. The principal design consideration is that an open-collector output is not a push-pull logic output. Select the pull-up resistor and logic voltage carefully, keep the pull-up current within the output sink-current rating, and place the device close enough to the protected signal path to minimize pickup of switching noise. The exposed package also requires attention to copper area and thermal conditions when either channel operates continuously at maximum load. This product page brings together the manufacturer family information, distributor listing attributes, package details, replacement guidance, and practical design considerations. It also distinguishes verified electrical attributes from parameters that require confirmation from the LM293 manufacturer datasheet, helping engineers plan a replacement or design-in without relying on package-code assumptions.

RFQ İletişim