Ürünler (44.000+)

MC1458DT - High-Performance Dual Op Amp | STMicroelectronics
MC1458DT

MC1458DT - High-Performance Dual Op Amp | STMicroelectronics

The STMicroelectronics MC1458DT is a high-performance, monolithic, dual operational amplifier with a wide input common-mode voltage range, supplied in an 8-pin SOIC package. The device contains two amplifiers and is intended for general-purpose analog signal-conditioning applications. Its high gain, wide operating-voltage range, and general feedback architecture support integrator, summing-amplifier, comparator-style, and precision feedback designs. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The MC1458 belongs to the operational-amplifier family, which is part of the broader analog IC and semiconductor hierarchy. Operational amplifiers are used wherever a circuit must amplify, buffer, filter, integrate, or compare a small electrical signal, making them foundational building blocks in instrumentation, control, communications, and consumer equipment. Key features of the MC1458 include its dual-amplifier configuration, high-performance monolithic construction, wide input common-mode voltage range, and low power consumption. The dual format allows two independent amplifier channels in one package, reducing board area and simplifying designs that require matched amplification stages. Its general-purpose feedback configuration makes it useful in both conventional closed-loop amplifier circuits and active analog networks. The MC1458 is specified for a wide range of operating voltages, which gives designers flexibility when using it with different supply rails and signal levels. The device is suitable for integrator and summing-amplifier applications because its high gain and feedback characteristics support accurate closed-loop operation. The manufacturer describes the MC1458 as intended for a wide range of analog applications rather than a single narrow use case. Typical applications include audio preamplification, sensor signal conditioning, analog filtering, instrumentation, general feedback control, and low-frequency analog signal processing. Its SOIC-8 package also makes it practical for conventional PCB assembly where dual-channel analog amplification is required. Designers should verify supply voltage, input common-mode range, output swing, stability, and load requirements against the manufacturer datasheet for the exact operating conditions. When designing around the MC1458DT, use appropriate input and output bypassing, keep feedback paths short, and verify that the selected operating point remains inside the device's electrical limits. This page combines the verified manufacturer and distributor information with practical selection guidance and drop-in cross-reference context for engineers evaluating the MC1458 family.

RFQ İletişim
MC1458ID - Dual High-Performance Operational Amplifier | STMicroelectronics
MC1458ID

MC1458ID - Dual High-Performance Operational Amplifier | STMicroelectronics

The STMicroelectronics MC1458ID is a high-performance dual operational amplifier integrated circuit with two amplifier circuits in an 8-pin SOIC package. It is intended for general-purpose analog signal-processing applications, including summing amplifiers, voltage followers, integrators, active filters, and function generators. The device is identified as a low-noise, wide-temperature-range dual op amp with short-circuit protection and no frequency-compensation requirement. An operational amplifier is a voltage-feedback analog amplifier used to amplify the difference between two input voltages. In a feedback network, the MC1458ID can provide high closed-loop gain, signal buffering, impedance transformation, and active-filter functions. Its dual-circuit architecture places two independent amplifiers in one package, reducing board area when a design requires two analog signal channels. The MC1458ID is described as a high-performance monolithic dual operational amplifier with low power consumption and a large input-voltage range. The device also features high gain, short-circuit protection, no-latch-up behavior, and operation without frequency compensation. These characteristics make it suitable for instrumentation, audio signal processing, active filtering, summing and integrating circuits, and general analog control systems. The MC1458ID uses a conventional dual-amplifier architecture rather than a digitally controlled or precision-specialty amplifier. Its two channels are packaged in an 8-SOIC, allowing a compact surface-mount implementation. The wide operating-voltage capability supports varied analog supply conditions, while the low-noise designation is relevant to applications in which signal integrity and small-signal amplification matter. Typical uses include audio preamplification, instrumentation buffering, active filters, summing amplifiers, integrators, voltage followers, and function-generator circuits. In an instrumentation application, the device can buffer sensor outputs before conversion or further processing. In audio systems, one channel may process one signal path while the second handles another, provided the power supply and grounding arrangement support both circuits. When designing around the MC1458ID, use the manufacturer pin-description table to assign supply, input, and output connections, and observe the dual-amplifier decoupling requirements. Place bypass capacitors close to the supply pins, keep feedback-loop routing short, and check input and output signal limits against the device operating conditions before finalizing the board layout. This product page combines the STMicroelectronics MC1458ID device identity, package information, functional applications, sourcing structure, and practical design guidance to support faster component selection and board-level implementation.

RFQ İletişim
MC1458IDT - Dual 1 MHz Op Amp | STMicroelectronics
MC1458IDT

MC1458IDT - Dual 1 MHz Op Amp | STMicroelectronics

The STMicroelectronics MC1458IDT is a high-performance, monolithic dual operational amplifier with two amplifier circuits, a 1 MHz gain-bandwidth product, a 0.8 V/µs slew rate, and an 8-pin SOIC package. Its 30 nA input bias current supports low-loading signal acquisition, while the wide input common-mode range expands the usable input span for general-purpose analog designs. An operational amplifier is an analog building block used to amplify voltage differences and implement feedback-based functions such as voltage followers, summing amplifiers, integrators, comparators, and active filters. The MC1458 belongs to the dual general-purpose operational-amplifier family, combining two independent amplifiers in one package. This integration reduces board area in analog systems that need more than one amplifier but do not require rail-to-rail inputs or low-noise instrumentation performance. The device's 1 MHz gain-bandwidth product makes it suitable for moderate-speed feedback networks and audio-frequency signal conditioning. Its 0.8 V/µs slew rate limits how quickly the output can follow large voltage changes, so stable feedback compensation and suitable loop-gain choices remain important. The 30 nA input bias current is particularly useful when driving relatively high-impedance sensors or resistive networks, because input loading has less effect on the source signal. Each amplifier in the MC1458 can operate from a wide range of supply voltages, enabling operation in both conventional single-supply and dual-supply analog systems. STMicroelectronics describes the MC1458 as a monolithic dual operational amplifier intended for integrators, summing amplifiers, and general feedback applications. Short-circuit protection and an absence of latch-up behavior support dependable use in conventional amplifier topologies. Typical applications include audio preamplification, low-frequency active filtering, instrumentation signal conditioning, voltage buffering, summing and difference amplifiers, and general feedback control. In a voltage follower, the high input impedance limits source loading. In an integrator or active filter, component tolerances and amplifier bandwidth determine usable frequency range. The SOIC-8 package is suitable for conventional surface-mount assembly and exists in tape-and-reel distribution format. When designing around the MC1458IDT, preserve signal headroom at the amplifier output and keep feedback-loop bandwidth compatible with the 1 MHz gain-bandwidth product. Place input, output, and compensation components close to their associated pins, and avoid long high-impedance traces that can increase noise pickup. Decoupling capacitors should connect directly across the supply pins to minimize supply-to-ground loop area. This product page combines the STMicroelectronics family description with a practical breakdown of the MC1458IDT's amplifier count, bandwidth, slew rate, bias current, package, and application roles. It also provides replacement guidance, pin-location information, comparison criteria, and design notes for engineers evaluating the MC1458 against other general-purpose dual operational amplifiers.

RFQ İletişim
MC1458IN - Dual High-Performance Op Amp | STMicroelectronics
MC1458IN

MC1458IN - Dual High-Performance Op Amp | STMicroelectronics

STMicroelectronics MC1458IN is a dual, high-performance, general-purpose operational amplifier packaged in an 8-pin Mini DIP. Each integrated circuit contains two amplifier channels, allowing one component to implement independent amplification, buffering, summing, integration, or feedback functions. The device is specified as a standard general-purpose amplifier, and a distributor listing identifies a slew rate of 0.8 V/µs. It is supplied in the through-hole DIP-8 package represented by the MC1458IN ordering code. An operational amplifier, or op amp, is a high-gain analog building block that compares its inverting and non-inverting inputs and drives an output toward the difference between those voltages, subject to negative feedback. Within the product hierarchy, the MC1458IN is a dual op amp, which is a type of analog amplifier IC used for instrumentation, signal conditioning, voltage following, active filtering, summing, and feedback control. The MC1458 family provides two amplifiers in one monolithic package, reducing component count while preserving independent operation of both channels. Key features include two amplifier circuits in one package, a high-performance monolithic design, general-purpose feedback compatibility, a stated 0.8 V/µs slew rate, and an 8-pin Mini-DIP mounting format. These characteristics make the device suitable for analog systems requiring two precision-oriented signal paths without allocating two separate single amplifier packages. The through-hole package also supports conventional DIP sockets and prototype-board assembly. According to the STMicroelectronics manufacturer datasheet, the MC1458 is intended for a wide range of analog applications, including integrators, summing amplifiers, and general feedback circuits. Its high gain and broad operating-voltage capability support conventional closed-loop analog designs, while the integrated dual configuration allows signal conditioning and active feedback stages to be placed close together on a board. Typical applications include audio preamplification, instrumentation stages, active filters, analog summing networks, integrators, buffer amplifiers, and general industrial signal conditioning. In a dual-rail circuit, the two channels can process separate inputs or participate in cascaded stages. In single-supply equipment, the usable input and output range still requires careful common-mode and output-swing verification against the manufacturer specifications. Designers should check the datasheet pinout, recommended operating voltages, common-mode range, output swing, offset specifications, compensation requirements, and supply decoupling before finalizing a board. Feedback-network values and source impedances should be selected against the documented frequency-response and noise characteristics rather than estimated from generic 741-family behavior. This page consolidates verified manufacturer and distributor information, documented equivalent-family references, package-level comparison data, and practical selection guidance. It also distinguishes verified facts from parameters that still require confirmation from the current manufacturer datasheet, helping engineers qualify replacements without assuming undocumented electrical equivalence.

RFQ İletişim
MC1458N - Dual High-Performance Op Amp | STMicroelectronics
MC1458N

MC1458N - Dual High-Performance Op Amp | STMicroelectronics

STMicroelectronics MC1458N is a dual, internally compensated operational amplifier in an 8-pin Mini DIP package. The device combines two amplifiers in one monolithic IC, providing high open-loop gain, a high common-mode input range, internal compensation, short-circuit protection, and exceptional temperature stability. Its wide operating-voltage range makes it suitable for conventional bipolar power supplies and general analog signal-processing systems. An operational amplifier is an analog IC that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to control gain, bandwidth, and output behavior. The dual MC1458 belongs to the operational-amplifier hierarchy, which extends to analog amplifiers and signal-conditioning ICs. Two independent amplifiers in one package reduce board area and simplify designs requiring matched channel functions. The MC1458's internal compensation removes the need for external frequency-compensation components in standard closed-loop configurations. Its high open-loop gain supports accurate amplification in feedback circuits, while its broad common-mode range accommodates signals around the circuit's bias point. Short-circuit protection improves robustness when an output is overloaded. The product is identified by distributors as a standard, general-purpose, two-circuit amplifier. STMicroelectronics describes the MC1458 as a high-performance monolithic dual operational amplifier intended for a wide range of analog applications. The combination of high gain and wide operating-voltage capability supports integrator and summing-amplifier designs, as well as conventional closed-loop feedback circuits. Because both amplifiers share one package, matching of channel behavior can be beneficial in precision audio, instrumentation, and analog-control products. Typical uses include audio preamplification, active filters, summing amplifiers, integrators, sensor-signal conditioning, and general feedback-based analog stages. The dual topology is especially useful when a board needs two gain stages with a common supply arrangement. The 8-pin Mini DIP through-hole package is also convenient for legacy equipment, educational circuits, and repair applications where a surface-mount footprint would be unsuitable. Designers should verify the exact supply-voltage, input-voltage, output-current, gain-bandwidth, input-offset, and output-swing limits from the manufacturer datasheet before finalizing a new design. Input and output stability must also be checked with the selected feedback network and load. Because through-hole devices can be affected by socket contact resistance, lead oxidation, and longer analog traces, prototype measurements are recommended before production use. This page combines the verified manufacturer and distributor information for MC1458N with package-aware replacement guidance, application context, comparison parameters, and practical design notes. It distinguishes confirmed device characteristics from electrical details that still require verification from the current manufacturer datasheet.

RFQ İletişim
MC1458P - Dual 1 MHz 30 V Operational Amplifier | Texas Instruments
MC1458P

MC1458P - Dual 1 MHz 30 V Operational Amplifier | Texas Instruments

The Texas Instruments MC1458P is a dual general-purpose operational amplifier in an 8-pin PDIP package, providing two amplifier channels per device. The verified manufacturer data identifies the MC1458 family as a dual, 30 V, 1 MHz operational amplifier, while the MC1458P ordering information identifies the P suffix as the 8-pin PDIP configuration. The amplifiers are designed for conventional analog signal conditioning, including voltage-follower, amplifier, comparator, summing, and general feedback applications. The manufacturer datasheet states that the devices have a high common-mode input voltage range, no latch-up, short-circuit protection, and internal frequency compensation, allowing operation without external compensation components in standard closed-loop configurations. The absence of offset-null capability distinguishes the MC1458 family from the µA741-style devices with null pins, so applications requiring external offset adjustment should use an alternative amplifier with offset-null access. The MC1458P is not a rail-to-rail input or output device based on the verified source information; the available manufacturer description instead emphasizes its wide common-mode input voltage range and high operating voltage. With a 30 V maximum supply framework and 1 MHz gain-bandwidth capability, the device is suitable for audio, instrumentation, industrial control, test and measurement, and general-purpose analog circuits. The internally compensated architecture and short-circuit protection simplify implementation in designs requiring two amplifier channels in one package. Engineers should verify input and output voltage limits, common-mode range, output-current capability, noise, offset, slew rate, and supply-current requirements against the current manufacturer datasheet before production release. This page combines the verified manufacturer and distributor descriptions with package-specific ordering information, practical design notes, and verified cross-reference candidates for engineers evaluating a DIP-8 operational-amplifier replacement.

RFQ İletişim
MC1458PG4 - Dual 30V 1MHz Op Amp | Texas Instruments
MC1458PG4

MC1458PG4 - Dual 30V 1MHz Op Amp | Texas Instruments

Texas Instruments MC1458PG4 is a dual general-purpose operational amplifier designed for a 30 V maximum supply and 1 MHz gain-bandwidth operation, supplied in an 8-pin PDIP package. Each channel provides independent signal amplification for analog control, instrumentation, buffering, and signal-conditioning circuits where a conventional through-hole dual op amp is preferred. An operational amplifier, commonly called an op amp, is an analog amplifier with very high open-loop gain. When negative feedback surrounds the device, that gain becomes precise and stable, allowing an analog signal to be amplified according to the surrounding resistor network. A dual operational amplifier contains two amplifier sections in one package, making it useful when a board needs two related analog functions without using two separate IC packages. The MC1458PG4's defining performance figures are its two-channel configuration, 30 V supply capability, and 1 MHz gain-bandwidth product. These characteristics position it as a general-purpose amplifier rather than a precision or high-speed signal-processing device. The 8-pin PDIP format also supports conventional through-hole assembly, breadboard prototyping, educational designs, and maintenance of existing industrial hardware. Each amplifier section supports common analog-building functions such as voltage following, non-inverting amplification, inverting amplification, summation, subtraction, filtering, and level conditioning. Negative feedback determines the closed-loop gain, while resistor and capacitor values establish the operating characteristics of the surrounding circuit. The dual organization allows paired operations in one package, including two voltage followers or an inverting stage followed by another conditioning stage. Typical uses include low-frequency industrial control loops, sensor-signal conditioning, audio preamplification at modest bandwidths, educational analog-circuit demonstrations, and legacy equipment repairs. The 1 MHz gain-bandwidth figure is particularly relevant for general-purpose signal paths rather than wideband video, high-fidelity audio, or precision instrumentation. System designers should calculate closed-loop bandwidth from the required gain and confirm that signal amplitude and slew-rate requirements remain compatible. For PCB implementation, place the device so the eight leads can be inspected and routed cleanly, maintain separation between input and output paths, and provide local supply bypassing where practical. Stable operation depends on suitable feedback compensation, adequate supply bypassing, and keeping source impedances low enough for the selected gain. The two channels are intended for similar analog environments and do not eliminate the need to verify common-mode, output-swing, and stability limits in the finished design. This product reference combines the manufacturer's key amplifier ratings, package information, sourcing guidance, documented drop-in alternatives, and practical selection advice. It is intended to help engineers identify whether the MC1458PG4 fits an existing 8-pin dual-op-amp design and what electrical and layout checks to complete before production release.

RFQ İletişim
MC1458PS - Dual 30V 1MHz Op Amp | Texas Instruments
MC1458PS

MC1458PS - Dual 30V 1MHz Op Amp | Texas Instruments

The Texas Instruments MC1458PS is a dual general-purpose operational amplifier with two internally compensated amplifier channels, a 30 V rating, and a 1 MHz gain-bandwidth product in an 8-pin SOIC package. The MC1458 family combines short-circuit protection, wide common-mode and differential input-voltage ranges, low power consumption, and latch-up-free operation. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare and amplify small voltage differences. The MC1458 belongs to the general-purpose operational-amplifier family within the broader analog IC and semiconductor hierarchy. Its two channels can operate independently for signal conditioning, voltage following, summing, integration, or other feedback-based amplifier configurations. Each MC1458 channel offers a 1 MHz gain-bandwidth product, 500 V/ms slew rate, and 90 dB common-mode rejection in the supplied product data. The reported input bias current is 1.5 µA, input offset current is 200 nA, and typical input offset voltage is 6 mV. Internal frequency compensation eliminates the need for external compensation components in the manufacturer's standard voltage-follower application. The MC1458 architecture is intended for general-purpose precision amplification rather than high-speed or rail-to-rail operation. Its wide common-mode input range makes it suitable for conventional bipolar-supply circuits, while the absence of latch-up improves robustness during power sequencing and input-overvoltage events. Short-circuit protection helps limit output current when an output is overloaded, although sustained short-circuit duration and internal current limits should be confirmed in the manufacturer datasheet. Typical uses include audio preamplification, summing amplifiers, active filters, sensor-signal conditioning, industrial control blocks, and general voltage-following circuits. Two amplifiers in one package can reduce component count and simplify dual-channel or differential signal-path layouts. The commercial MC1458PS temperature grade is 0 °C to +70 °C, making it appropriate for room-temperature industrial and consumer equipment rather than exposed automotive or extreme-temperature installations. PCB design should reserve adequate copper around the supply pins and route each channel's feedback components close to the associated amplifier pins to reduce parasitic feedback and instability. Decoupling capacitors should be placed directly between each supply pin and ground. Because this is a non-rail-to-rail, bipolar general-purpose amplifier, input and output common-mode headroom must be checked against the actual supply voltages. This page combines verified manufacturer and distributor information, drop-in family alternatives, package and pinout details, application guidance, and design notes to provide more implementation context than the basic distributor catalog entry.

RFQ İletişim
MC1458PSR - Dual 30V 1MHz Op Amp | Texas Instruments (Tape & Reel)
MC1458PSR

MC1458PSR - Dual 30V 1MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments MC1458PSR is a dual general-purpose operational amplifier with two internally compensated amplifier channels, a 30 V rating, and a 1 MHz gain-bandwidth product in an 8-pin SOIC package. The MC1458 family combines short-circuit protection, wide common-mode and differential input-voltage ranges, low power consumption, and latch-up-free operation. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare and amplify small voltage differences. The MC1458 belongs to the general-purpose operational-amplifier family within the broader analog IC and semiconductor hierarchy. Its two channels can operate independently for signal conditioning, voltage following, summing, integration, or other feedback-based amplifier configurations. Each MC1458 channel offers a 1 MHz gain-bandwidth product, 500 V/ms slew rate, and 90 dB common-mode rejection in the supplied product data. The reported input bias current is 1.5 µA, input offset current is 200 nA, and typical input offset voltage is 6 mV. Internal frequency compensation eliminates the need for external compensation components in the manufacturer's standard voltage-follower application. The MC1458 architecture is intended for general-purpose precision amplification rather than high-speed or rail-to-rail operation. Its wide common-mode input range makes it suitable for conventional bipolar-supply circuits, while the absence of latch-up improves robustness during power sequencing and input-overvoltage events. Short-circuit protection helps limit output current when an output is overloaded, although sustained short-circuit duration and internal current limits should be confirmed in the manufacturer datasheet. Typical uses include audio preamplification, summing amplifiers, active filters, sensor-signal conditioning, industrial control blocks, and general voltage-following circuits. Two amplifiers in one package can reduce component count and simplify dual-channel or differential signal-path layouts. The commercial MC1458PSR temperature grade is 0 °C to +70 °C, making it appropriate for room-temperature industrial and consumer equipment rather than exposed automotive or extreme-temperature installations. PCB design should reserve adequate copper around the supply pins and route each channel's feedback components close to the associated amplifier pins to reduce parasitic feedback and instability. Decoupling capacitors should be placed directly between each supply pin and ground. Because this is a non-rail-to-rail, bipolar general-purpose amplifier, input and output common-mode headroom must be checked against the actual supply voltages. This page combines verified manufacturer and distributor information, drop-in family alternatives, package and pinout details, application guidance, and design notes to provide more implementation context than the basic distributor catalog entry.

RFQ İletişim
MC14600P - Low-Power CMOS Alarm IC w/ Horn Driver | NXP DIP-16
MC14600P

MC14600P - Low-Power CMOS Alarm IC w/ Horn Driver | NXP DIP-16

The NXP MC14600P is a low-power CMOS alarm IC with integrated piezoelectric horn driver and LED driver, housed in a 16-pin DIP (through-hole) package. It is engineered to convert an analog alarm-level voltage condition into a tone output for a piezo horn and/or an LED indicator with extremely low average current draw, making it ideally suited to long-life battery-operated alarm systems. The part integrates a low-battery detection feature that monitors supply voltage and a minimal external RC network to configure its operating thresholds. An alarm IC is a specialized consumer circuit in the broader semiconductor family of alarm and supervisory ICs (alarm IC -> supervisory circuit -> power management IC). Its role in a system hierarchy is to sit between an analog sensor (smoke, gas, heat) or a manually triggered switch network and the audible/visual annunciation stage, removing the need for a microcontroller in single-function safety devices. The MC14600 sits at the low-power end of this family, distinct from microcontroller-based alarm SoCs and from generic buzzers or piezos. Key features include a low average current requirement optimized for battery life, integrated horn driver capable of directly driving a piezoelectric transducer or small speaker, an LED driver pin for visual indication of alarm state, an on-chip low-battery detection comparator with adjustable threshold via an external resistor divider, and CMOS construction for low quiescent drain. The alarm and low-battery detect inputs both have internal hysteresis to prevent false triggering. Only a handful of external passive components - typically an RC timing network, an input divider, and a piezo element - are required to form a complete alarm subsystem. Architecturally the device uses a CMOS analog and digital mixed-signal block: a precision voltage reference, two comparator channels (alarm input and low-battery input), a piezo tone generator, and output drivers capable of sourcing/sinking the piezo and LED loads. The low-battery detect logic shares the same internal reference as the alarm comparator, ensuring consistent behavior over temperature. The CMOS process and integrated drivers eliminate the need for an external transistor to drive the horn. Typical applications include standalone smoke detectors, gas-leak detectors, and personal-security panic alarms where low standby current is critical. Industrial equipment-monitoring alarm circuits, portable medical alarm devices, and battery-powered temperature or liquid-level alarms also benefit from this part. The wide operating temperature range supports both commercial and industrial environments. Design considerations focus on selecting the input-divider resistor values to match the chosen alarm sensor threshold, sizing the timing RC for the desired tone cadence, and ensuring the piezo element's voltage rating matches the device's horn-driver swing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the basic datasheet pinout table.

RFQ İletişim
MC1488D - Quad EIA-232D Driver | onsemi | RS-232 Interface
MC1488D

MC1488D - Quad EIA-232D Driver | onsemi | RS-232 Interface

The onsemi MC1488D is a monolithic four-channel EIA-232D line driver with a 14-pin SOIC package. It provides four current-limited differential outputs intended to interface data terminal equipment with data communications equipment, with typical output current limited to ±10 mA and a minimum power-off source impedance of 300 ohms. An EIA-232D line driver is a type of RS-232 interface driver that converts logic-level signals into the voltage-domain signals used by RS-232 communications equipment. Within the broader hierarchy, it is a line driver and interface IC within communications and power-management signal conditioning. Its four channels allow one package to support several unidirectional data paths when the system already provides the required receiver and supply circuitry. Key features include four independent driver channels, typical current-limited output of ±10 mA, and a minimum power-off source impedance of 300 ohms. The current limiting helps control output current when a receiver or connected circuit imposes an abnormal load. The MC1488D also provides simple slew-rate control, an important characteristic for reducing unwanted transitions on slow RS-232 links. Technically, the device is designed around the EIA-232D interface requirements identified in the onsemi datasheet. Because MC1488D contains drivers rather than receivers, it cannot replace a complete RS-232 transceiver without external receiver circuitry. In a typical interface, logic signals enter the driver inputs and leave through four EIA-232D output channels. The receiver and any required level translation are separate functions. Typical uses include legacy RS-232 ports, data terminal equipment, data communications equipment, industrial control interfaces, and embedded systems that retain an EIA-232D connection. The MC1488D is also useful as the transmit-side element in a multi-channel interface where a companion receiver IC is already present. Designers should verify the supported supply voltage, input thresholds, output levels, timing, and absolute maximum ratings directly against the manufacturer datasheet before implementation. PCB layout should preserve short output paths, provide an appropriate ground reference, and avoid placing sensitive analog signals beside the driver outputs. This page combines verified manufacturer and distributor information, source-backed drop-in candidates, interface-selection guidance, and practical PCB considerations to provide engineering context beyond a basic MC1488D catalog listing.

RFQ İletişim
MC1488DG - Quad EIA-232D Driver | onsemi | RS-232 Interface
MC1488DG

MC1488DG - Quad EIA-232D Driver | onsemi | RS-232 Interface

onsemi MC1488DG is a monolithic quad line driver designed to interface data terminal equipment with data communications equipment using the EIA-232D standard. The device provides four driver channels, operates from a 5 V supply, and uses a 14-pin SOIC package. Its typical output current is ±10 mA per channel, with current limiting built into the outputs. The MC1488DG is intended for RS-232 transmitter functions rather than receiver functions, so it must be paired with a suitable quad receiver when full bidirectional communication is required. An EIA-232D line driver is a type of interface transceiver component that converts logic-level signals into RS-232 voltage levels for transmission between data terminal equipment and data communications equipment. In the broader hierarchy, MC1488DG belongs to the interface IC category, specifically the RS-232 driver family. Its quad-channel architecture reduces the component count in systems requiring several serial data outputs while preserving the signal and power connection conventions established for EIA-232D equipment. The principal features of MC1488DG include four independent driver outputs, integrated output current limiting, and a typical output current capability of ±10 mA. The driver is designed for conformance with EIA-232D interface requirements, and its monolithic construction places the driver functions in one 14-pin SOIC package. The design supports equipment requiring multiple RS-232 transmit channels, including computer peripherals, industrial data links, test equipment, and legacy communications equipment. Technically, the MC1488 belongs to the family of bipolar RS-232 line drivers that use positive and negative supply rails to develop the bipolar voltage levels required by the interface standard. The MC1488 data also identifies SN55188 and SN75188 as related monolithic quadruple line drivers. Because MC1488DG is a driver-only device, engineers should check signal levels, supply requirements, output polarity, and protection needs against the original system interface before using it in a redesigned board. Typical applications include industrial serial-port controllers, laboratory instrumentation, point-of-sale terminals, data acquisition equipment, and embedded systems that retain an RS-232 output interface. In a multi-channel design, each logic input can drive a corresponding RS-232 output, while a separate receiver IC handles incoming signals. This separation is important because the MC1488 provides four transmit channels but no integrated receive channels. A key design consideration is to preserve the original board footprint and verify every pin assignment before substitution. The 14-pin SOIC package is suitable for conventional surface-mount assembly, but RS-232 cables connect to externally exposed connector pins rather than directly to the IC. External protection, grounding, connector geometry, and cable-routing decisions remain necessary to achieve reliable system-level communications. This page combines the verified manufacturer and distributor references for MC1488DG with package information, interface intent, sourcing links, and identified pin-compatible alternatives. It also distinguishes the driver-only MC1488DG from complete RS-232 transceiver functions, helping engineers select the correct replacement without confusing interface direction or package compatibility.

RFQ İletişim
MC1488DR2 - 4-Channel RS-232 Driver | onsemi | SOIC-14
MC1488DR2

MC1488DR2 - 4-Channel RS-232 Driver | onsemi | SOIC-14

The onsemi MC1488DR2 is a four-channel RS-232 line driver with no receiver channels, designed for EIA-232D data-terminal and data-communications interfaces. The device operates from dual positive and negative supplies of ±15 V, provides typical current-limited outputs of ±10 mA, and is packaged in a surface-mount 14-pin SOIC measuring 3.90 mm wide. An RS-232 line driver is a specialized interface-circuit component that converts logic-level signals from a digital system into the voltage levels required by an RS-232 communications port. The MC1488 family belongs to the broader line-driver and interface-IC hierarchy, where four independent driver channels can support multiple serial links, control signals, or communications ports within one package. Key features include four independent driver outputs, support for EIA-232D signaling, current limiting at approximately ±10 mA typical, and operation from ±15 V supplies. Its 14-SOIC surface-mount construction makes it suitable for compact communications and industrial-control equipment. Each channel provides a separate driver path, allowing multiple logic signals to be shifted into RS-232-compatible levels. The MC1488 uses separate positive and negative supply rails rather than a single low-voltage rail. This architecture is appropriate when the surrounding equipment already provides ±15 V or requires legacy RS-232 voltage levels. Board designers must account for the relationship between input logic levels, supply polarity, output current, and the load presented by the RS-232 interface. Typical applications include legacy RS-232 ports, data-terminal interfaces, industrial equipment connections, test systems, and embedded control panels. In these systems, the MC1488DR2 can convert four TTL or CMOS-compatible control signals into RS-232 levels while operating with standard ±15 V communications supplies. A critical design consideration is the need to observe supply sequencing and the limits of the RS-232 interface. Place bypass capacitors close to the supply pins, maintain short return paths, and confirm that the connected cable and receiver tolerate the driver’s output characteristics before finalizing the layout. This page organizes the MC1488DR2 specifications, sourcing information, drop-in candidates, and application guidance to support faster design review. Because the MC1488DR2 is identified as obsolete, lifecycle planning and verified alternate sourcing are especially important for new and maintenance designs.

RFQ İletişim
MC1488M - Quad EIA-232D Driver, SOIC-14 | onsemi
MC1488M

MC1488M - Quad EIA-232D Driver, SOIC-14 | onsemi

onsemi MC1488M is a monolithic quad line EIA-232D driver with four current-limited outputs, supplied in a 14-pin SOIC package. The device provides typical output currents of ±10 mA and a minimum power-off source impedance of 300 Ω. It is designed to interface data terminal equipment with data communications equipment using the EIA-232D signal convention. An EIA-232D line driver is a transmitter within the broader interface IC and RS-232 transceiver categories. Its role is to convert logic-level transmit signals into bipolar voltage levels suitable for EIA-232D communication links. The MC1488M contains four independent driver channels, allowing one package to support multiple serial-data outputs in equipment such as modems, computer interfaces, industrial communications equipment, and legacy peripheral systems. The principal features of the MC1488M include four driver channels, typical current-limited output capability of ±10 mA, a 300 Ω minimum power-off source impedance, and EIA-232D interface conformance. Its 14-pin SOIC package supports surface-mount PCB assembly while reducing the footprint required by a discrete transistor driver arrangement. The M suffix identifies the surface-mount ordering variant presented by onsemi. Internally, the MC1488M combines four line-driver stages with supply-voltage protection arrangements described in the associated device literature. Its monolithic construction provides a practical alternative to separate transistor or MOSFET driver circuits. Because the output stage is designed to source and sink current rather than operate as a logic-level CMOS output, the circuit should be evaluated as an EIA-232D interface stage, not as a general-purpose push-pull logic driver. Typical uses include four-channel RS-232 transmit ports, data terminal equipment, data communications equipment, printer interfaces, and industrial data links. Designers combining this driver with a receiver can construct a complete asymmetric RS-232 interface. The component is especially relevant to legacy systems that require more than two independently driven EIA-232D outputs while retaining a surface-mount footprint. The primary design consideration is the external interface network and supply arrangement. EIA-232D implementations commonly use series resistors and capacitive or diode-clamped protection to manage transient conditions, while supply bypassing must be placed close to the device. Engineers should also verify receiver compatibility, cable requirements, logic levels, and all electrical limits against the manufacturer datasheet before substituting the part into a live design. This product page consolidates the verified manufacturer and distributor information for MC1488M with package details, sourcing guidance, practical design notes, and a strict assessment of available drop-in alternatives. Where the supplied source material does not establish an exact same-package replacement, the page identifies that limitation instead of presenting an unverified substitution as drop-in compatible.

RFQ İletişim
MC1488MEL - Quad EIA-232D Driver | onsemi
MC1488MEL

MC1488MEL - Quad EIA-232D Driver | onsemi

The onsemi MC1488MEL is a monolithic quad line driver designed to interface data terminal equipment with data communications equipment in accordance with EIA-232D requirements. The device provides four independent driver channels and is specified for operation with ±15 V supply voltages. It is packaged in the onsemi SOEIAJ-14, a 14-pin small-outline surface-mount package with a 5.30 mm package width. A line driver is an interface IC that converts low-voltage logic signals into differential, bipolar RS-232-style voltage levels for transmission over a serial communication link. In the broader hierarchy, the MC1488MEL belongs to the RS-232 driver and receiver family, within interface ICs and data-communication semiconductors. Its four channels allow one package to support multiple unidirectional serial lines, reducing board area compared with separate single-channel drivers. The principal feature of the MC1488MEL is its quad EIA-232D line-driver architecture. The manufacturer describes the MC1488 as a monolithic quad line driver with current-limited outputs and an operating supply arrangement of approximately ±15 V. This architecture is useful when a system needs to translate TTL or CMOS-side control signals into the voltage levels expected by an RS-232 interface, particularly where multiple unidirectional channels are required. The MC1488MEL is specified for commercial-extended temperature-grade applications. Its 14-terminal surface-mount construction is intended for automated PCB assembly and compact equipment designs. The package is identified as SOEIAJ-14 rather than a generic 14-pin SOIC designation, so engineers should use the manufacturer pin configuration and land pattern associated with that specific package when laying out a replacement board. Typical uses include industrial control equipment, data-terminal interfaces, RS-232 communication ports, peripheral connections, and legacy serial-control systems. Because it is a driver rather than a combined transceiver, the application must provide a separate receiver when a complete bidirectional RS-232 port is required. Review signal polarity, supply sequencing, cable routing, and grounding before using the device in a new design. For power planning, use the datasheet’s absolute-maximum and recommended operating conditions rather than assuming that ±15 V is the only acceptable implementation. The device’s output stage is intended for current-limited RS-232 driver operation, but the PCB still needs appropriate supply decoupling and controlled return paths. This page focuses on the MC1488MEL’s function, package, interface role, and replacement considerations.

RFQ İletişim
MC1488MG - Quad EIA-232D Driver | onsemi | RS-232
MC1488MG

MC1488MG - Quad EIA-232D Driver | onsemi | RS-232

The onsemi MC1488MG is a monolithic four-channel RS-232 line driver with a 4/0 driver-to-receiver configuration, current-limited outputs rated at ±10 mA typical, and a 14-pin gull-wing SOIC package. It is designed for data-terminal equipment and data-communications equipment that require an EIA-232D-compatible transmit interface. The MC1488MG is identified as the commercial extended-temperature grade in distributor and catalog records. An RS-232 line driver is an interface IC that converts digital logic-level signals into unbalanced, bipolar voltage levels suitable for serial data links. Within the signal-chain hierarchy, it belongs to the RS-232 interface-driver family, combines with an RS-232 receiver to form a complete communications path, and ultimately provides the physical-layer function required between data terminal equipment and data communications equipment. Unlike a transceiver, the MC1488MG provides four driver channels and no receiver channels. The primary verified characteristics are four independently available line-driver outputs, EIA-232D conformance, typical current limiting of ±10 mA, a 14-pin SOIC package with gull-wing leads, and a commercial extended temperature grade. The output current limit protects the driver stage when a connected RS-232 line is shorted or misconfigured. Because four transmit channels are provided, one device can support four RS-232 outputs while reducing the number of external line-driver packages required. The MC1488MG is intended for legacy and industrial serial-control equipment where EIA-232D signaling remains required. Appropriate uses include multi-port controller interfaces, equipment test systems, point-to-point serial links, and control panels. The device requires suitable bypass capacitance and careful grounding because the implemented system also depends on cable characteristics, receiver thresholds, protection networks, and the voltage levels allowed by the selected RS-232 endpoint. For new designs, engineers should verify signal polarity, baud rate, logic thresholds, and electrical limits against the current manufacturer datasheet before layout release. The supplied search results confirm the EIA-232D driver function, four-output organization, ±10 mA typical output current, and 14-pin SOIC format, but several detailed timing, voltage, temperature, and absolute-maximum values were not included in the retrieved records. This page combines verified distributor and manufacturer-linked information, structured technical context, pin-compatible replacement guidance, and practical sourcing notes. It also separates confirmed electrical facts from parameters that require datasheet verification, helping engineers avoid assigning unsupported specifications to this legacy-compatible RS-232 interface device.

RFQ İletişim
MC1488N - Quadruple RS-232 Line Driver | Texas Instruments
MC1488N

MC1488N - Quadruple RS-232 Line Driver | Texas Instruments

Texas Instruments MC1488N is a monolithic quadruple RS-232 line driver with four driver channels, 10 mA typical current-limited output, and a minimum 300 ohm power-off output impedance. Designed for data-terminal equipment and data-communications equipment interfaces, the device operates from a 5 V supply in a 14-pin PDIP package rated for 0 to 70 degrees C. A line driver is a digital interface circuit that converts low-voltage logic signals into RS-232-compatible voltage levels. The MC1488 belongs to the RS-232 driver hierarchy, where a line driver interfaces data-terminal equipment with data-communications equipment. Its four channels allow one package to support four unidirectional serial data paths, reducing component count in multi-port or multi-channel RS-232 equipment. The device is designed to meet or exceed ANSI EIA/TIA-232-E and ITU Recommendation V.28 requirements. According to the Texas Instruments manufacturer datasheet, each output includes current limiting, and the power-off output impedance is at least 300 ohms. A series diode is used at each supply-voltage terminal, while the output slew rate can be controlled through the load capacitance connected to each driver. The MC1488N is designed to be interchangeable with the Motorola MC1488, which supports PCB sourcing flexibility where the original function is required. The manufacturer datasheet identifies the MC1488, SN55188, and SN75188 as monolithic quadruple line drivers, but device ordering suffixes, temperature ranges, and package variants must still be checked before substitution. The N suffix identifies the 14-pin PDIP configuration shown in the verified Texas Instruments part-details data. Typical uses include RS-232 interfaces in data-terminal equipment, data-communications equipment, industrial control systems, point-of-sale equipment, printers, and legacy serial-port adapters. It is particularly useful where multiple RS-232 channels share a common logic interface and a through-hole package is preferred for serviceability or manual assembly. PCB layout should keep each driver output away from sensitive analog and high-speed digital traces because RS-232 transitions can produce edge-related EMI. The data input pins must be driven only when the supply is valid, and unused outputs should be handled according to the manufacturer datasheet rather than left as floating high-impedance nodes. Confirm output polarity and logic levels before interchanging it with a receive/transceiver device.

RFQ İletişim
MC1488NE4 - Quad RS-232 Line Driver 300kbps | Texas Instruments
MC1488NE4

MC1488NE4 - Quad RS-232 Line Driver 300kbps | Texas Instruments

The Texas Instruments MC1488NE4 is a quadruple RS-232 line driver with four independent drivers rated for data rates up to 300 kb/s, operating from dual supplies of 7.5 V to 15 V (positive) and the matching negative rail, in a 14-pin PDIP (N) package. A line driver is an interface IC that converts low-voltage logic-level signals from a UART or microcontroller into the larger voltage swings required by the EIA/TIA-232 (RS-232) serial communication standard. Within the signal-chain hierarchy, it sits between the digital controller and the physical serial cable, and forms a driver-receiver pair with companion parts such as the MC1489 quadruple line receiver. RS-232 remains common in industrial equipment, point-of-sale terminals, and legacy instrumentation despite newer USB and Ethernet links. The MC1488NE4 provides four drivers in one package, each with TTL/CMOS-compatible inputs and RS-232-level outputs. Output signal swing is set by the supply rails, allowing engineers to tailor output levels via the positive and negative supplies. Typical output current capability supports driving standard RS-232 cable capacitance at data rates up to 300 kb/s, per the manufacturer datasheet. The N suffix package is molded PDIP, suited to through-hole prototypes and repair of legacy boards. Architecturally, the part uses a monolithic bipolar process. Each driver contains ainput stage, phase-splitting stage, and output structure referenced between the two supply rails, producing output swings that meet EIA-232-E voltage requirements when supplies are appropriately chosen. Series elements at the supply terminals are used in the manufacturer's typical application to improve robustness. Typical applications include UART-to-RS-232 conversion in industrial terminals, modem and DTE-to-DCE interfacing, programming and debugging ports on legacy equipment, and educational/lab serial circuits. It pairs naturally with the MC1489 or DS1489 receiver on the far end of the link. Design consideration: the MC1488 requires both a positive and a negative supply rail - systems lacking a negative rail need a charge-pump converter such as the MAX232 family or ICL232, which integrate the voltage generation. Also verify power dissipation with multiple drivers switching simultaneously. This page adds value beyond the manufacturer datasheet by synthesizing drop-in alternative cross-references (DS14C88, SN75188, SN75C188), comparison tables, and practical design notes in one place for sourcing and design engineers.

RFQ İletişim
MC1488NG4 - Quad RS-232 Line Driver | Texas Instruments
MC1488NG4

MC1488NG4 - Quad RS-232 Line Driver | Texas Instruments

Texas Instruments MC1488NG4 is a monolithic quadruple RS-232 line driver containing four driver channels and no receiver channels in a 14-pin PDIP package. It is designed for data-terminal equipment interfacing with data-communications equipment in conformance with ANSI TIA/EIA-232-E. The device uses a diode in series with each supply-voltage terminal in the application configuration described by the manufacturer. An RS-232 line driver is an interface IC that converts logic-level signals into bipolar voltage levels suitable for RS-232 communications. Within the interface hierarchy, the MC1488 belongs to the line-driver and transceiver class, where a transmitter handles outbound data and a receiver handles inbound data. Because the MC1488 provides four drivers and no receivers, a complete communication channel generally requires a separate receiver IC and the associated interface protection. The primary feature of the MC1488NG4 is its four-driver organization in one 14-pin PDIP package. Four channels allow one driver IC to support multiple RS-232 outputs while reducing the number of external packages and board-space requirements. The device is specifically identified as a 4/0 RS-232 driver, meaning that it offers four driver functions and zero receiver functions. It is also associated with the MC1488, SN55188, and SN75188 device family in the manufacturer documentation. The MC1488 architecture uses current-limited driver outputs suited to interfaced RS-232 lines. In the documented typical application, a diode is placed in series with each supply-voltage terminal, allowing the supply arrangement to suit the system polarity and interface requirements. Designers should preserve that topology, validate output-level behavior with the intended cables and loads, and review the complete manufacturer datasheet before releasing a new layout. Typical uses include multi-port RS-232 equipment, data-terminal interfaces, industrial control panels, legacy data-collection systems, and communications equipment requiring several unidirectional outputs. The MC1488 can also be paired with a quad receiver such as the MC1489 family to create a complete differential-direction RS-232 interface on a board that still uses through-hole integrated circuits. PCB planning should allow the 14-pin PDIP to be installed without pin-1 errors, and signal-routing should keep driver outputs away from sensitive analog or high-speed digital traces. Adequate bypass capacitance and grounding remain essential for stable operation. The actual electrical limits, output-current behavior, supply range, temperature range, and timing or transition characteristics must be checked against the manufacturer datasheet before design sign-off. This product page consolidates the identified RS-232 functionality, package information, datasheet access, compatible interface-family options, and practical implementation guidance. It also distinguishes a genuine same-package line-driver alternative from receiver ICs, which may complement the MC1488NG4 but cannot replace its four driver outputs.

RFQ İletişim
MC1488P - Quad RS-232 Line Driver | STMicroelectronics
MC1488P

MC1488P - Quad RS-232 Line Driver | STMicroelectronics

The STMicroelectronics MC1488P is a monolithic quadruple RS-232 line driver with four differential driver channels in a 14-pin PDIP package. According to the verified manufacturer and distributor information, the device is intended to interface data terminal equipment with data communications equipment under EIA RS-232C and EIA-232D requirements. Its outputs are current limited to ±10 mA typical, while the power-off source impedance is specified at 300 ohms minimum. These characteristics make the MC1488P suitable for legacy RS-232 equipment requiring four unidirectional data channels, especially systems built around the classic MC1488 interface family. A line driver is a digital interface component that converts TTL-compatible logic signals into voltage levels suitable for a balanced or unbalanced communications link. In the broader electronics hierarchy, the MC1488P belongs to interface ICs, specifically the RS-232 driver category. It complements receiver ICs such as the MC1489 rather than operating as a complete bidirectional transceiver. Each of its four channels therefore supports one driven signal path per package. The principal verified features are the monolithic four-channel implementation, RS-232 interface purpose, ±10 mA typical current-limited outputs, 300 ohms minimum power-off source impedance, and 14-pin PDIP construction. The DigiKey listing identifies the device as a 4/0 RS-232 driver in a 14-DIP package, while Mouser categorizes it as a quad line driver. These are legacy communications characteristics rather than modern high-speed differential-interface specifications. The MC1488P is normally powered from separate positive and negative supply rails so that its output stage can generate RS-232 voltage levels from low-voltage logic. Exact supply limits, propagation delay, output-voltage levels, operating temperature, and absolute maximum ratings are not included in the supplied search records, so those values must be verified against the original manufacturer datasheet before a new design is released. The MC1488P may also need external charge-pump circuitry when used with modern single-supply systems because it does not include an on-chip RS-232 voltage converter. Typical uses include legacy serial-port adapters, industrial data-collection equipment, point-of-sale terminals, laboratory interfaces, and controller boards that exchange RS-232 signals with older peripherals. In each case, the MC1488P handles the transmit side, while a compatible receiver handles incoming signals. Software handshaking, ground continuity, and protection against external cable transients remain important system-level considerations. Designers should preserve the original 14-pin footprint and verify pin functions, supply rails, and logic thresholds against the applicable datasheet. Decoupling capacitors should be placed close to the supply pins, and cable-side protection may be required for industrial environments. Because the verified sources identify both STMicroelectronics and onsemi offerings, purchasing decisions should also account for manufacturer traceability, lifecycle status, and approved-source documentation. This page consolidates the verified RS-232 line-driver description, distributor identification, package information, drop-in substitution evidence, and practical design considerations into one engineering-focused reference. It also distinguishes verified facts from specifications that still require confirmation from the complete manufacturer datasheet.

RFQ İletişim
MC1488PG - Quad RS-232 Line Driver | onsemi | PDIP-14
MC1488PG

MC1488PG - Quad RS-232 Line Driver | onsemi | PDIP-14

The onsemi MC1488PG is a monolithic quadruple RS-232 line driver with four driver outputs, designed for EIA-232D data-terminal and data-communications equipment interfaces. The device operates from a single positive supply, provides current-limited outputs with a typical ±10 mA output capability, and is packaged in a 14-pin PDIP format. Its four independent channels allow one interface IC to drive four RS-232 data signals while reducing the number of packages required on a communications board. An RS-232 line driver is a digital interface component that converts TTL-compatible logic levels into bipolar voltage levels suitable for transmission over an RS-232 port. A line driver belongs to the broader interface IC hierarchy and works alongside line receivers, transceivers, and protection devices in the wider data-communications and industrial-control equipment category. The MC1488 therefore provides the transmit-side function in a conventional RS-232 interface, while a separate receiver is required for incoming signals. Key features include four driver channels in one monolithic package and current-limited outputs rated to ±10 mA typical. The MC1488PG is associated with EIA-232D interface requirements and uses a 14-pin PDIP package for through-hole PCB assembly. These characteristics make it suitable for legacy computer ports, industrial control links, embedded serial equipment, and other systems that continue to use the bipolar RS-232 physical interface. The four driver outputs allow several communications lines to share the same supply and package, reducing PCB component count compared with discrete single-channel driver designs. Because the outputs are current limited, the device is suited to driving conventional RS-232 loads rather than high-current or long-distance cable networks. Designers should still provide the required bypass capacitance, observe the supply-voltage limits, and verify receiver and cable characteristics at the system level. Typical applications include multi-channel RS-232 equipment interfaces, legacy PC communication ports, test instruments, point-to-point industrial serial links, and embedded control systems. The four-channel arrangement is particularly useful when a board must transmit several RS-232 signals through a single interface package. A complementary receiver, such as a compatible RS-232 receiver IC, is required when the same port must also receive data. For a new PCB, confirm the manufacturer's MC1488 datasheet for the exact pin assignment, supply limits, output-current conditions, and decoupling recommendations. For an existing board, verify footprint, pinout, logic polarity, and operating-voltage compatibility before substitution, especially when the assembly includes protection networks or unusual cable loading. This product page combines the MC1488PG device identity, RS-232 design considerations, drop-in replacement guidance, and practical application context to help engineers evaluate legacy-interface repair, modernization, and sourcing decisions without relying on a raw catalog listing.

RFQ İletişim
MC1489AD - Quad EIA-232D Receiver IC | onsemi
MC1489AD

MC1489AD - Quad EIA-232D Receiver IC | onsemi

onsemi MC1489AD is a monolithic quad line receiver designed to connect data terminal equipment with data communications equipment conforming to EIA-232D. The device contains four receivers in a 14-pin SOIC package and is identified by the DigiKey listing as a 0/4 RS-232 receiver. According to the onsemi datasheet, its input resistance is specified from 3.0 kΩ to 7.0 kΩ. An EIA-232D line receiver is a type of interface IC that converts bipolar serial data from a communications port into a digital logic signal for a host, peripheral, or data-processing system. The receiver belongs to the RS-232 interface hierarchy, which connects equipment using the EIA-232D electrical standard. A quad receiver consolidates four receive channels into one package, reducing board area and simplifying multi-port or multi-peripheral serial interfaces. The MC1489AD is intended for systems in which external equipment presents EIA-232D signals to the receiving circuit. Its four-channel arrangement is useful for control consoles, communications equipment, industrial peripherals, and legacy data-terminal interfaces. The specified input resistance helps define the loading placed on the signal source, while the integrated receiver channels reduce the number of discrete interface components required at the system boundary. Because this device receives rather than transmits EIA-232D signals, it does not perform the voltage conversion normally assigned to an RS-232 driver. Designers must pair it with the appropriate line-driver circuitry when a design requires bidirectional serial communication. Likewise, the application schematic must observe the polarity, voltage levels, and timing requirements of the connected EIA-232D interface rather than treating the receiver inputs as ordinary CMOS inputs. The principal design consideration is verifying that the PCB land pattern and pin assignments match the 14-pin SOIC ordering of the MC1489AD. The package suffix identifies a surface-mount variant, but the complete numbered pin list must be taken from the manufacturer pin-description table before tracks are assigned. Signal routing should keep the receive paths away from noisy switching nodes, and unused receiver channels should be configured according to the datasheet rather than left open without guidance. Typical implementations include industrial serial consoles, data-terminal equipment, communications interfaces, test systems, and embedded systems that must acquire EIA-232D data from external equipment. The principal trade-off is its specialized interface purpose: it addresses legacy or long-established EIA-232D links but does not replace modern differential buses such as RS-422 or RS-485. This product page organizes the MC1489AD’s confirmed electrical characteristics, package information, cross-reference considerations, and application guidance. It also distinguishes genuine pin-compatible replacements from electrically similar parts that use a different package or pin arrangement, helping engineers avoid a substitution that compiles but cannot be soldered onto the original footprint.

RFQ İletişim
MC1489AM - Quad EIA-232D Receiver | onsemi | SOIC-14
MC1489AM

MC1489AM - Quad EIA-232D Receiver | onsemi | SOIC-14

onsemi MC1489AM is a monolithic quad line receiver designed to interface data terminal equipment with data communications equipment conforming to EIA-232D. The device combines four receiver channels in a 14-pin SOIC package, with an input resistance specified from 3.0 kΩ to 7.0 kΩ and an input signal range extending to 30 V. It is intended for systems that receive bipolar RS-232 signals and translate them into logic-level signals for the receiving equipment. The MC1489AM is a receiver-only device rather than a combined RS-232 transceiver. An EIA-232D line receiver belongs to the interface IC hierarchy, where it sits between a physical communication port and digital logic. RS-232 uses single-ended bipolar signaling, so a receiver must identify valid positive and negative voltages while rejecting signals outside the accepted logic thresholds. The four independent channels of the MC1489AM allow one package to handle four serial ports, four peripheral connections, or several control signals carrying the same receiver electrical characteristics. The primary electrical feature is its 3.0 kΩ to 7.0 kΩ input resistance. This relatively high impedance limits loading on the transmitting side and is useful when several receiver inputs must observe a signal source. The 30 V input signal range provides tolerance for voltage excursions on the physical line. Because the package contains four channels, it also reduces component count and board space compared with four separate single-channel receiver packages. The MC1489AM is specifically identified as an EIA-232D receiver rather than a modern transceiver with integrated charge-pump voltage generation. In a complete RS-232 interface, the MC1489AM is used on the receive path, while a separate line driver handles the transmit path. This separation can be advantageous in asymmetric equipment, test systems, industrial controllers, and legacy installations where the number of transmitted and received signals differs substantially. Common applications include industrial serial-port interfaces, data terminal equipment, data communications equipment, peripheral controllers, instrumentation, and legacy computer equipment. Designers should provide the interface system with an appropriate common reference and route the receive outputs directly into the receiving logic or level-shifting circuitry required by the host device. When laying out a circuit using the MC1489AM, keep the receiver close to the connector or protected signal entry point to minimize the distance over which unprotected RS-232 signals can pick up noise. The input network should avoid excessive loading because the receiver input resistance can vary across the stated 3.0 kΩ to 7.0 kΩ range. Confirm the complete pin assignment, voltage limits, and system enable requirements against the manufacturer datasheet before fabrication. This product page combines the verified device identity, package information, and electrical characteristics with application guidance, design considerations, and a conservative drop-in replacement assessment. It is structured to help engineers identify the correct receiver function, plan the interface architecture, and avoid treating functionally similar receivers as pin-compatible replacements.

RFQ İletişim
MC1489AMG - Quad EIA-232D Receiver | onsemi | RS-232
MC1489AMG

MC1489AMG - Quad EIA-232D Receiver | onsemi | RS-232

The onsemi MC1489AMG is a monolithic quad line receiver designed to connect data terminal equipment with data communications equipment conforming to EIA-232D. It provides four receiver channels in a 14-pin SOIC package, with an input resistance of 3.0 kΩ to 7.0 kΩ and an input signal range of ±30 V. The component is intended for receiving bipolar RS-232 signals in multi-channel serial-interface systems. A quad line receiver is an interface IC that converts bipolar RS-232 voltage levels into complementary TTL-compatible logic signals. In the hierarchy of electronic components, it belongs to the line-receiver class, then interface IC, then digital interface and communication semiconductor. The MC1489 family is designed for equipment in which multiple data or control channels must be received from a single 14-pin package. The primary features of the MC1489AMG are its four independent EIA-232D receiver channels, broad input signal range, and moderate input resistance. The ±30 V input capability provides tolerance for the voltage excursions associated with RS-232 communication links, while the 3.0 kΩ to 7.0 kΩ input resistance provides the loading behavior expected by the interface circuit. The commercial extended temperature grade identifies its intended operating environment. Each receiver accepts a differential-looking pair of RS-232-related input pins and produces a corresponding logic output. Integrating four channels reduces the number of packages and interconnections needed for multi-port systems. The MC1489AMG contains receivers only; it does not provide the voltage-level translation used to transmit RS-232 signals, so a complementary line-driver device is required when a design needs both transmission and reception. Typical uses include industrial data acquisition, point-of-sale equipment, serial adapters, test instruments, and embedded systems that receive multiple RS-232 channels. The 14-pin SOIC package is appropriate for conventional through-hole or mixed-technology PCB assembly. Because an RS-232 receiver does not terminate or protect a physical cable, systems still require suitable cable routing, grounding, surge protection, and interface-level consideration. A key design practice is to verify the complete MC1489 pin description and typical application circuit in the onsemi datasheet before assigning board nets. Keep the RS-232 input traces away from clocks, fast digital signals, and switching-power-node areas. Provide a stable supply reference for the logic side of the interface and place any required bypass capacitance close to the device supply pins. This page combines the manufacturer interface definition, package and electrical characteristics, drop-in alternatives, application guidance, and PCB-oriented design notes. These resources help engineers distinguish a true pin-compatible receiver from a merely similar RS-232 transceiver and plan a board revision with fewer interface-integration risks.

RFQ İletişim