Ürünler (44.000+)

MCP2562FD-E/SN - CAN FD Transceiver, 8-SOIC | Microchip
MCP2562FD-E/SN

MCP2562FD-E/SN - CAN FD Transceiver, 8-SOIC | Microchip

The Microchip Technology MCP2562FD-E/SN is a second-generation high-speed CAN Flexible Data Rate (CAN FD) transceiver that interfaces a CAN protocol controller to the physical two-wire CAN bus, housed in an 8-pin SOIC (SN) package. It supports data rates up to 8 Mbps in CAN FD mode, 5 Mbps in classic CAN mode with high-speed slew rate, and operates over a VIO supply range of 1.8V to 5.5V for direct MCU interface. Key features include a maximum loop delay of 130 ns and guaranteed loop delay symmetry to support CAN FD bit timing requirements. The device operates across an ambient temperature range of -40C to +125C and survives load dump transients up to +/- 70V on the bus pins through integrated protection. A CAN transceiver serves as the physical-layer interface between a CAN protocol controller (such as the MCP2518FD or integrated CAN module on a microcontroller) and the differential CAN bus (CANH/CANL). It translates the controller's transmit (TXD) and receive (RXD) digital logic into the differential bus signaling defined by ISO 11898-2:2016, and provides the dominant and recessive states needed for non-destructive bitwise arbitration. CAN FD extends the classic CAN payload from 8 bytes to 64 bytes while remaining backward-compatible at the physical layer, which is why FD-compliant transceivers like the MCP2562FD are now preferred even for classic CAN designs. The MCP2562FD delivers 5 key advantages. First, the integrated VIO pin eliminates level shifters when interfacing 1.8V/3.3V MCUs. Second, low loop-delay symmetry (<=130 ns total) enables reliable 2 Mbps and 5 Mbps CAN FD operation. Third, +/- 36V receiver common-mode range tolerates large ground shifts across nodes. Fourth, +/- 70V bus-pin transient protection (IEC 61000-4-2 ESD and load dump) eliminates external TVS diodes in most automotive 12V/24V systems. Fifth, an ultra-low-current standby mode (~15 uA typical) preserves battery life in always-bus-wake applications. The MCP2562FD uses a 1.8V to 5.5V VIO supply rail that sets the logic level reference for TXD, RXD, and the standby (STBY) pin, while the VCC/VSUP rail (4.5V to 5.5V) powers the bus-side driver. An on-chip LDO from VCC to VIO is provided on the -H variants; the -E/SN variant requires the user to supply VIO externally for maximum flexibility. The integrated slope-control circuitry automatically adjusts the CANH/CANL edge rate to meet ISO 11898-2:2016 at any speed between 50 kbps and 5 Mbps, so no external resistor selection is required. Typical applications include automotive gateway ECUs, body-control modules, ADAS sensor CAN buses, industrial PLC networking, agricultural machinery CAN backbones, and any battery-powered remote sensor that needs an always-listening low-power mode. It also suits prototypes and maker projects using boards such as the Teensy, Arduino, and Raspberry Pi that need a CAN shield with simple 3.3V logic. When designing with this device, route the CANH/CANL traces as a 120-ohm differential pair with characteristic impedance of 120 ohms and place a 120-ohm termination resistor at each end of the bus; place a 100 nF decoupling capacitor as close as possible to the VCC and VIO pins to suppress switching noise from the bus driver. This page synthesizes distributor pricing, drop-in cross-brand alternatives, and practical layout guidance not found in the manufacturer datasheet.

RFQ İletişim
MCP3001-I/MS - 10-Bit SPI ADC | Microchip Technology
MCP3001-I/MS

MCP3001-I/MS - 10-Bit SPI ADC | Microchip Technology

The Microchip Technology MCP3001-I/MS is a 10-bit, single-input successive-approximation-register analog-to-digital converter with a 200 ksample/s sampling rate, SPI serial interface, and 8-pin MSOP package. It is designed for embedded control systems that require a compact, low-power analog measurement input. An analog-to-digital converter is an interface IC that converts a continuously varying voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3001 belongs to the SAR ADC family and the broader ADC and data-converter hierarchy. Its internal sample-and-hold function, SPI interface, and low-power characteristics support efficient acquisition in temperature sensing, industrial measurement, and general embedded control equipment. Key features include 10-bit resolution, one analog input channel, a 200 ksample/s conversion rate, and compatibility with SPI modes 0,0 and 1,1. The manufacturer documentation identifies maximum DNL and INL of ±1 LSB. The -I grade ordering code denotes Microchip's industrial temperature grade, although the exact numerical temperature limits are not present in the supplied web data and therefore require confirmation from the datasheet before use. The MCP3001 uses a successive-approximation conversion architecture. A conversion is initiated after chip select is asserted, and the ADC samples the selected analog input while communicating successive conversion information over the serial interface. The host processor supplies the command bits, reads the converted result, and controls the sampling sequence. This architecture is appropriate when conversion speed, interface simplicity, and low system cost matter more than the throughput or channel count of a higher-performance ADC. Typical uses include digital thermometers, environmental sensors, process-control instrumentation, battery monitoring, laboratory measurement equipment, and embedded analog front ends. The single SPI-compatible channel also makes the device useful in compact designs where a microcontroller has adequate timer and serial-port resources for chip-select handling and clock generation. When designing a PCB for the MCP3001-I/MS, place the device close to the analog source and route the analog input away from noisy switching nodes and high-current traces. Provide a clean reference voltage, confirm the input range against the chosen supply voltage, and keep the SPI traces short. Review the datasheet for the exact recommended input and reference-decoupling network rather than assuming that generic bypass values are sufficient.

RFQ İletişim
MCP3001-I/P - 10-Bit Single-Channel SPI ADC | Microchip
MCP3001-I/P

MCP3001-I/P - 10-Bit Single-Channel SPI ADC | Microchip

The Microchip Technology MCP3001-I/P is a 10-bit, single-channel, successive-approximation-register analog-to-digital converter with a 200 ksps sampling rate, supplied in an 8-pin PDIP package. It combines low-power operation with an SPI-compatible serial interface, making it suitable for embedded control systems that require one analog measurement channel. The verified distributor data identifies the device as a 1-input, 1-SAR ADC with an industrial temperature range of -40°C to 85°C. An ADC is an integrated circuit that converts an analog voltage into a digital code for processing by a microcontroller, control system, or data-acquisition unit. The MCP3001 belongs to the successive-approximation-register ADC family, which samples an analog input and compares it with an internal reference through a sequence of successive approximation steps. Its 10-bit resolution provides 1024 digital codes across the selected input range, while the SPI interface transfers the conversion result to a host controller. Key verified characteristics include 10-bit resolution, one analog input, SAR architecture, 200 ksps sampling, SPI data access, and an 8-pin PDIP package. The -40°C to 85°C operating range supports industrial temperature environments, although the provided data does not include detailed electrical limits such as supply voltage, input voltage range, reference voltage, conversion timing, or power consumption. The MCP3001-I/P is therefore best evaluated against the complete manufacturer datasheet before final circuit design. Typical application areas include industrial control panels, temperature and pressure monitoring, embedded sensor interfaces, laboratory measurement systems, and low-channel-count data acquisition. The single SPI interface allows a microcontroller to initiate a conversion and read the resulting code, while the compact PDIP package supports through-hole PCB assembly and prototype development. The primary design consideration is analog-signal conditioning. The input should remain within the device's verified operating limits, and the host firmware must account for the ADC resolution, reference voltage, input range, and sampling timing. This page combines verified distributor specifications, manufacturer positioning, comparison data, and practical integration guidance for engineers evaluating the MCP3001-I/P.

RFQ İletişim
MCP3001-I/SN - 10-Bit 200 kSPS SPI ADC | Microchip
MCP3001-I/SN

MCP3001-I/SN - 10-Bit 200 kSPS SPI ADC | Microchip

The Microchip Technology MCP3001-I/SN is a 10-bit, single-channel successive-approximation analog-to-digital converter with a 200 kSPS sampling rate, SPI serial interface, and 8-pin SOIC package. It operates from a single 5.5 V supply and includes an on-chip sample-and-hold circuit. An ADC converts an analog voltage into a numeric code for processing by a microcontroller, logic controller, or embedded system. The MCP3001 belongs to the SAR ADC hierarchy: successive approximation compares the sampled input against an internal reference and generates a 10-bit conversion result. Its pseudo-differential single input provides a simple interface for potentiometers, resistive sensors, dividers, and industrial control signals while reducing the component count compared with a multiplexed multi-channel converter. Key features include 10-bit resolution, differential nonlinearity and integral nonlinearity specified at a maximum of ±1 LSB, an on-chip sample-and-hold circuit, and serial communication using SPI-compatible modes 0,0 and 1,1. A single 5.5 V supply simplifies power planning, while the 200 kSPS conversion rate supports rapid sensor acquisition and straightforward embedded sampling loops. The MCP3001 uses a serial interface rather than a parallel data bus, reducing the number of connections required between the converter and host controller. Conversion results are shifted out through the combined clock/data pin, while chip select controls the serial transaction. This architecture suits compact control boards where pin availability, board area, and power consumption are more important than maximum channel count. Typical applications include analog front-end conditioning, potentiometer position sensing, temperature or light sensor monitoring, battery-voltage measurement, and industrial embedded control. The 10-bit result provides 1,024 quantization steps, which is appropriate for many slow-changing control signals but may be insufficient for high-precision instrumentation without additional gain, averaging, or oversampling. When designing around the MCP3001-I/SN, protect the analog input from transients, bypass the analog supply close to the device, and provide a stable reference voltage. Source impedance and acquisition time should be checked against the datasheet because settling errors can degrade the least significant bits. The SPI clock and chip-select timing must also satisfy the serial-interface specifications for reliable conversion completion. This page consolidates distributor availability, verified electrical characteristics, same-footprint alternatives, package and temperature details, and practical PCB guidance for engineers evaluating the MCP3001-I/SN as a drop-in 8-SOIC ADC.

RFQ İletişim
MCP3001-I/ST - 10-Bit SPI ADC | Microchip Technology
MCP3001-I/ST

MCP3001-I/ST - 10-Bit SPI ADC | Microchip Technology

The Microchip Technology MCP3001-I/ST is a 10-bit, single-input analog-to-digital converter using a successive approximation register, or SAR, architecture with an SPI-compatible serial interface and an 8-pin TSSOP package. It operates from a 2.7 V supply according to the manufacturer datasheet, making it suitable for embedded control systems that sample one analog voltage. The device combines a 10-bit conversion resolution, one analog input channel, and low-power operation in a compact surface-mount footprint. An ADC is an integrated circuit that converts a continuously varying analog voltage into a digital value for processing, storage, or transmission. The MCP3001 belongs to the SAR ADC family within the broader data-acquisition IC and power-management semiconductor hierarchy. Its SAR architecture repeatedly compares the input against an internally generated reference to determine each bit of the result, providing a straightforward interface for microcontrollers and other digital controllers. The verified product information identifies a 10-bit conversion resolution, one analog input, SAR conversion technology, and an SPI-compatible serial connection. These characteristics make the MCP3001 useful where a controller must monitor a single sensor or control signal without implementing a higher-cost or higher-channel converter. The 8-pin TSSOP package also reduces board area compared with larger analog packages, although the narrow lead pitch requires careful assembly and layout. The MCP3001-I/ST is specified for industrial-temperature product ordering, while the temperature limits and detailed electrical limits require confirmation from the manufacturer datasheet. The device also uses a low-power operating concept, as described by Microchip Technology for embedded-control applications. Exact sampling rate, conversion-time, reference-voltage range, input-voltage range, and current-consumption figures are not included in the supplied verified records and therefore are not inferred here. Typical uses include single-channel potentiometer sensing, industrial control-loop monitoring, battery or power-rail measurement, and analog control inputs for embedded systems. In a typical circuit, the microcontroller selects the conversion by asserting chip select, clocks the converter through SCLK, and reads the result from DOUT. A microcontroller with an SPI master peripheral, such as the ATMEGA328P or STM32F072RBT7TR listed in the site MPN collection, can provide the required clocking and data handling. Designers should treat VREF and supply bypassing as critical high-impedance analog nodes. The analog input should be kept short, away from switching-current paths, and referenced to the same ground structure used by the converter. Before production release, verify the exact pin assignment, reference-voltage limits, input range, acquisition timing, and operating-temperature limits against the manufacturer datasheet rather than relying on generic ADC assumptions. This product record combines verified manufacturer and distributor information with package-aware selection guidance, practical interface notes, and a transparent data-availability assessment. It also identifies the limited drop-in alternatives that could be substantiated from the supplied cross-reference results, avoiding unsupported substitutions based only on similar resolution or interface specifications.

RFQ İletişim
MCP3001T-I/ST - 10-Bit 200ksps SPI ADC | Microchip Technology
MCP3001T-I/ST

MCP3001T-I/ST - 10-Bit 200ksps SPI ADC | Microchip Technology

The Microchip Technology MCP3001T-I/ST is a 10-bit, single-channel successive-approximation-register analog-to-digital converter designed for embedded control systems. It operates from a 2.7 V supply, supports sampling rates up to 200 ksps, and uses an SPI-compatible serial interface. The device is offered in an 8-pin TSSOP package and is identified by the automotive-oriented AEC-Q100 designation in the product listing. An ADC is an interface component that converts a continuous analog voltage into a digital number that a microcontroller, digital signal processor, or other embedded controller can process. The MCP3001 belongs to the SAR ADC family, which compares the input voltage with an internal reference through a sequence of approximation steps. Its 10-bit resolution provides 1,024 selectable codes, while its single analog input channel keeps the device and PCB layout compact for sensors, controls, and instrumentation. The MCP3001T-I/ST combines low power consumption with a small package and a straightforward serial interface. The manufacturer describes the MCP3001 as suitable for embedded control applications, where the device can digitize a conditioned sensor signal and transfer the result through serial data, clock, and chip-select lines. The SPI interface allows the ADC to share a serialized bus with other peripherals when the system includes appropriate chip-select control. The 2.7 V minimum operating supply makes the MCP3001 suitable for low-voltage embedded systems, provided the analog input remains within the input range allowed by the selected reference voltage. The ADC uses a reference-voltage arrangement rather than an internally fixed measurement range, allowing the system designer to select the reference according to sensor output and desired full-scale conversion. Proper reference bypassing and analog grounding remain important because reference stability directly affects conversion accuracy. The MCP3001T-I/ST is commonly used in temperature sensing, potentiometer and position measurement, industrial control, consumer equipment, and low-speed data acquisition. When selecting an external reference, check its accuracy, temperature coefficient, noise, and startup behavior. Place input and reference capacitors close to their associated pins, keep analog and digital return currents separated, and provide a clean supply path to minimize conversion errors. Designers should use the manufacturer datasheet for the complete pin-description table, recommended application circuit, electrical limits, and timing information. The TSSOP footprint is suitable for compact embedded boards, but thermal performance and soldering process requirements still apply. The device is a single-channel ADC, so applications requiring simultaneous sampling of multiple inputs need multiplexing or a different converter architecture.

RFQ İletişim
MCP3002-I/MS - 10-Bit Dual-Channel SAR ADC | Microchip
MCP3002-I/MS

MCP3002-I/MS - 10-Bit Dual-Channel SAR ADC | Microchip

The Microchip Technology MCP3002-I/MS is a 10-bit, dual-channel successive-approximation analog-to-digital converter with a 200 ksample/s sampling rate, a 2.7 V minimum supply, and an SPI serial interface. It is packaged in an 8-pin MSOP measuring approximately 0.118 inch, or 3.00 mm, wide. The converter accepts two analog inputs and can be configured for single-ended or pseudo-differential operation according to the manufacturer product-page information. An ADC, or analog-to-digital converter, is an integrated circuit that converts a continuously varying analog voltage into a numeric code for processing by a microcontroller or other digital controller. Within the signal-chain hierarchy, the MCP3002-I/MS is a data-conversion IC, specifically a SAR ADC with an SPI interface. SAR conversion repeatedly resolves the input voltage through a successive comparison process, making this device suitable for embedded instrumentation that prioritizes low complexity, serial integration, and modest resolution. Key features include 10-bit resolution, a maximum sampling rate of 200 ksample/s, two analog input channels, and a serial peripheral interface. The converter supports single-ended or pseudo-differential analog-input configurations, allowing one differential measurement to be represented as a pair of related input channels. The manufacturer materials also identify a maximum differential nonlinearity of ±1 LSB and a maximum integral nonlinearity of ±1 LSB. Its small MSOP package supports compact embedded-control layouts where component area and PCB routing efficiency are important. The SPI interface connects the ADC to a host microcontroller through serial data, clock, chip-select, and supply-reference connections. A 10-bit result provides 1,024 possible codes, while the two channels allow related analog quantities to be sampled without using two separate converter packages. Designers must still establish suitable analog input conditioning, reference-voltage stability, grounding, and digital-bus signal integrity to obtain repeatable measurements. Typical uses include industrial temperature and pressure monitoring, embedded process-control measurements, low-speed sensor acquisition, and general-purpose control systems. Its 200 ksample/s rate is substantially higher than many slow environmental sensors require, while the 10-bit resolution is appropriate for measurement systems that do not need the resolution of a high-precision sigma-delta or successive-approximation converter with more than 10 bits. A critical design consideration is analog-reference and grounding quality because conversion accuracy depends on the reference voltage and the sampled input being represented reliably. Place decoupling capacitance close to the supply pins, use a low-impedance reference path, and keep analog input routing away from fast SPI clock edges. The verified source excerpts do not provide complete pricing, pin-level descriptions, temperature limits, or absolute accuracy curves, so those values require confirmation in the manufacturer datasheet.

RFQ İletişim
MCP3002-I/P - 10-Bit Dual-Input SPI ADC | Microchip Technology
MCP3002-I/P

MCP3002-I/P - 10-Bit Dual-Input SPI ADC | Microchip Technology

The Microchip Technology MCP3002-I/P is a 10-bit dual-input successive-approximation analog-to-digital converter with a 200 ksps sampling rate, onboard sample-and-hold circuitry, and an SPI serial interface in an 8-pin PDIP package. It operates from a single 2.7 V supply, supports one pseudo-differential input pair or two single-ended inputs, and is designed for embedded-control measurements. Its 10-bit resolution, dual 0–1023 conversion codes, and integrated sampling front end make it useful for industrial controls, temperature sensing, potentiometers, and low-speed instrumentation. An ADC is a data-acquisition IC that converts an analog voltage into a numeric code. The MCP3002 belongs to the SAR ADC family, within analog-to-digital converters and broader data-conversion semiconductors. SAR conversion uses a successive comparison process to determine the analog input’s digital representation. This architecture offers predictable sampling behavior and works well with microcontrollers that implement the corresponding SPI transaction protocol. The MCP3002 combines two 10-bit conversion channels with an SPI interface, onboard sample-and-hold circuitry, and a maximum sampling rate of 200 kSPS. Input selection supports either a single pseudo-differential channel or dual single-ended channels. The verified manufacturer and distributor data identify a 2.7 V operating supply and an operating-temperature range of -40°C to +85°C for the I/P grade, making the device appropriate for industrial-temperature embedded systems. Its SPI interface allows a host microcontroller to initiate conversion, receive the 10-bit result, and determine channel information without parallel wiring. The converter is particularly useful where analog measurements must be added to a PIC or other SPI-capable embedded controller. Because the interface is serial, the MCP3002 reduces signal count compared with a parallel ADC while preserving 10-bit measurement resolution. Typical applications include two-channel sensor acquisition, potentiometer position measurement, temperature or pressure transducer interfaces, battery and supply monitoring, embedded instrumentation, and low-speed industrial control. The 200 ksps sampling rate is suitable for many continuously monitored control signals, while designers should verify acquisition timing, input bandwidth, reference stability, and system-level error when designing the analog front end. For reliable operation, connect the analog and digital grounds according to the manufacturer guidance and place the required bypass and input-conditioning components close to the converter. The analog input range must remain within the device limits, and the reference voltage determines conversion scaling. Firmware must implement the exact SPI command and sample timing specified by the manufacturer rather than treating the converter as a generic SPI ADC. This page combines verified manufacturer and distributor specifications, source-linked product information, and practical engineering guidance for embedded ADC designs. Pricing and availability references are current only as of 2026-10-23, and engineers should check current distributor stock and lead time before placing production orders.

RFQ İletişim
MCP3002-I/SN - 10-Bit 2-Channel 200ksps SAR ADC | Microchip
MCP3002-I/SN

MCP3002-I/SN - 10-Bit 2-Channel 200ksps SAR ADC | Microchip

The Microchip Technology MCP3002-I/SN is a 10-bit, 2-channel successive-approximation analog-to-digital converter with a 200 ksps sampling rate, SPI serial interface, and 2.7 V supply operation in an 8-pin SOIC package. The MCP3002-I/SN combines two analog input channels with a single SAR conversion engine and on-board sample-and-hold circuitry, making it suitable for embedded control systems that require compact, serial-output data acquisition. An ADC is an analog-to-digital converter, a category of interface IC that converts continuous voltage signals into numeric values for processing by a microcontroller, DSP, or other digital controller. The MCP3002 belongs to the SAR ADC family, using successive approximation to determine each conversion result. This architecture is well suited to embedded measurement and control because it provides predictable sampling operation, an SPI interface, low power consumption, and a small package. The verified product information identifies a resolution of 10 bits, two analog input channels, and a maximum sampling rate of 200 ksps. Its SPI serial interface allows the converter to communicate efficiently with a host controller using serial clock, data, and chip-select signals. The MCP3002-I/SN is also identified as an AEC-Q100 automotive-grade option, while its 8-pin SOIC package supports conventional surface-mount assembly. Because the MCP3002 uses a single ADC with two input channels, the available measurements must be scheduled by the host controller. The SAR conversion process and on-board sample-and-hold circuitry support acquisition of changing analog signals, while the 10-bit format provides 1,024 possible digital codes. Exact input ranges, conversion timing, reference-voltage limits, and channel input impedance were not included in the supplied verified records and should be confirmed in the manufacturer datasheet before final circuit design. Typical uses include industrial sensor interfaces, automotive control modules, potentiometer monitoring, temperature-sensor measurement, and general embedded data acquisition. In each case, the MCP3002 can convert one or two analog voltage inputs into serial data for a microcontroller or other controller. The 200 ksps rate is especially useful for higher-speed monitoring than typical slow sensor channels require. When laying out a circuit, place the converter close to the analog source and route the SPI signals away from noisy switching nodes. Provide a clean reference and supply arrangement, and verify that the selected input range supports the sensor voltage. Confirm the pinout and pin numbers in the official Microchip datasheet before PCB release, because the supplied search records did not provide a verifiable pin-by-pin assignment. This product record combines the verified manufacturer description, distributor specifications, package information, AEC-Q100 designation, current distributor pricing, and practical ADC selection guidance. It also distinguishes verified facts from parameters that still require datasheet confirmation, helping engineers evaluate the MCP3002-I/SN without relying on unverified substitutions.

RFQ İletişim
MCP3002-I/ST - 10-Bit Dual-Channel SAR ADC | Microchip
MCP3002-I/ST

MCP3002-I/ST - 10-Bit Dual-Channel SAR ADC | Microchip

The Microchip Technology MCP3002-I/ST is a 10-bit, dual-channel successive-approximation analog-to-digital converter with a 200 ksps sampling rate, SPI serial interface, and 8-pin TSSOP package. It operates from a 2.7 V supply and combines on-board sample-and-hold circuitry with programmable analog input configurations for embedded control applications. An ADC is an interface IC that converts continuously varying analog voltages into numeric values for processing by a microcontroller or other digital controller. The MCP3002 belongs to the successive-approximation-register, or SAR, ADC family. Its SAR architecture performs conversion through repeated comparisons, providing a practical balance of resolution, sampling speed, power consumption, and implementation complexity for embedded measurement systems. The converter provides 10-bit resolution, two analog inputs, and a maximum sampling rate of 200 ksps. Inputs may be configured as one pseudo-differential pair or two single-ended inputs. According to the supplied manufacturer and distributor data, differential nonlinearity and integral nonlinearity are each limited to ±1 LSB maximum. The SPI interface supports modes 0,0 and 1,1 for flexible connection to embedded serial controllers. The MCP3002-I/ST also supports single-supply operation from 2.7 V, making it appropriate for low-voltage embedded systems. Its on-board sample-and-hold circuitry captures the input before conversion, while the serial interface transfers the result using chip select, clock, and data-input signals. These characteristics allow a microcontroller to request measurements without requiring a separate external sample-and-hold circuit. Typical applications include industrial sensor acquisition, battery-powered instrumentation, consumer controls, temperature monitoring, potentiometer interfaces, and general embedded data acquisition. The dual-input arrangement is especially useful when two related analog quantities must be measured within one compact 8-pin package. The MCP3002-I/ST is also identified as an automotive-qualified AEC-Q100 option by the supplied distributor data. Designers should provide stable input and reference paths, observe the SPI signal timing required by the converter, and keep sensitive analog traces away from fast digital switching nodes. Because the MCP3002 provides 10-bit rather than higher resolution, system gain, reference accuracy, noise filtering, and sensor conditioning can determine the practical precision of the final measurement. This product page consolidates the verified manufacturer, distributor, and cross-reference information with application guidance, design notes, package details, and an honest assessment of drop-in replacement availability. Unlike the manufacturer datasheet alone, it highlights implementation constraints and sourcing considerations for engineers evaluating the MCP3002-I/ST.

RFQ İletişim
MCP3002T-I/SN - 10-Bit Dual-Channel SPI ADC | Microchip
MCP3002T-I/SN

MCP3002T-I/SN - 10-Bit Dual-Channel SPI ADC | Microchip

Microchip Technology MCP3002T-I/SN is a 10-bit dual-channel successive-approximation analog-to-digital converter with a 200 ksample/s conversion rate, 2.7 V supply operation, and an 8-pin SOIC package. It combines an on-board sample-and-hold circuit with an SPI serial interface for compact embedded-control and data-acquisition systems. An analog-to-digital converter, or ADC, translates a continuously varying analog voltage into a numeric value that a microcontroller or other digital controller can process. The MCP3002 belongs to the SAR ADC family and the broader embedded data-converter hierarchy. Its dual input architecture can provide one pseudo-differential channel or two single-ended channels, making it suitable for sensor monitoring, control loops, and industrial measurement systems. Key features include 10-bit resolution, a 200 ksample/s sampling rate, and operation from a 2.7 V supply. The on-board sample-and-hold circuitry acquires the input voltage during each conversion, while the SPI interface provides a compact means of transferring conversion results. The device is designed for low-power embedded-control applications and supports both single-ended and pseudo-differential input configurations. Internally, the MCP3002 uses successive-approximation conversion, in which a sample-and-hold circuit captures the analog input and an internal comparator and DAC determine successive digital codes. The manufacturer describes maximum differential nonlinearity and integral nonlinearity of ±1 LSB. These characteristics are important when the ADC monitors slow or medium-speed signals where deterministic quantization behavior is more useful than very high conversion throughput. Typical uses include industrial process monitoring, temperature and pressure sensor interfaces, potentiometer position sensing, motor or actuator feedback, and low-speed data logging. It is particularly suitable when two analog inputs and a compact serial interface are required without allocating a large number of microcontroller pins. Designers should verify the analog input range, reference voltage, sampling time, and SPI timing against the manufacturer datasheet. The analog input must remain within the device’s specified operating limits, and the reference and bypass connections should be routed to minimize noise and conversion errors. The SOIC footprint also requires attention to exposed-pad or thermal considerations only if the selected package variant includes one. This page combines manufacturer specifications, application guidance, package information, and drop-in-replacement assessment to support faster component selection and PCB planning.

RFQ İletişim
MCP3002T-I/ST - 10-Bit Dual-Channel SPI ADC | Microchip
MCP3002T-I/ST

MCP3002T-I/ST - 10-Bit Dual-Channel SPI ADC | Microchip

The Microchip Technology MCP3002T-I/ST is a 10-bit dual-channel successive-approximation analog-to-digital converter with a 2.7 V minimum supply voltage, two analog input channels, and an SPI serial interface, packaged in an 8-pin TSSOP. It combines onboard sample-and-hold circuitry with a compact format for embedded control systems. An ADC is a semiconductor that converts an analog voltage into a digital number for processing by a microcontroller or another digital controller. The MCP3002 belongs to the successive-approximation ADC family, where an internal sample-and-hold circuit measures an analog input and a successive-approximation register performs the conversion. Its two-channel arrangement supports dual analog measurements without requiring two separate converter packages. The device provides 10-bit conversion resolution, a two-channel input configuration, and SPI communication. These characteristics make it suitable for reading potentiometers, temperature sensors, pressure sensors, and other externally conditioned analog signals. Its 8-pin TSSOP package also supports compact embedded-control layouts where board area and external connection count are important design constraints. SPI communication provides a straightforward connection to a host microcontroller because the converter uses dedicated serial-data and chip-select signals. The host controls sampling by asserting chip select and then exchanges conversion commands and output data over the serial interface. Exact sampling rate, input impedance, conversion-time, reference-voltage, and operating-temperature details should be taken from the manufacturer datasheet before setting the acquisition timing and signal-conditioning network. Typical uses include industrial control panels, environmental monitoring, laboratory instrumentation, and consumer equipment with one or two slowly changing analog inputs. In these systems, the MCP3002T-I/ST can convert conditioned sensor voltages into 10-bit values while the SPI interface shares communication wiring with other serial peripherals. A key design consideration is analog reference quality. The reference connection must be adequately decoupled, and sensor outputs must remain within the converter's allowed input range. Place the decoupling capacitor close to the supply and reference pins, route the analog input away from fast SPI edges, and verify conversion timing against the host clock before increasing the sampling frequency. This product page combines the manufacturer electrical description, package information, application guidance, comparison parameters, and practical PCB considerations so engineers can evaluate the MCP3002T-I/ST before integrating it into an embedded analog-measurement design.

RFQ İletişim
MCP3004-I/P - 10-Bit, 4-Channel SPI ADC | Microchip
MCP3004-I/P

MCP3004-I/P - 10-Bit, 4-Channel SPI ADC | Microchip

The Microchip MCP3004-I/P is a 10-bit, four-channel successive-approximation-register analog-to-digital converter with a 200 kSPS conversion rate, SPI serial interface, and 14-pin PDIP package. It operates from 2.7 V to 5.5 V and is designed for embedded-control systems that need compact, low-power four-channel data acquisition. What is an ADC? An analog-to-digital converter, or ADC, transforms continuously varying analog voltages into numeric values that a microcontroller or other digital controller can process. The MCP3004 belongs to the SAR ADC category: its successive-approximation register samples an input and performs conversion through a sequence of bit decisions. Within the broader hierarchy, it is an ADC, data-converter IC, interface IC, and embedded-control component. The MCP3004 supports four analog input channels that can be configured as single-ended inputs or pseudo-differential pairs, as described by the manufacturer documentation. Its SPI interface reduces the number of signal lines required compared with a parallel ADC. The verified family documentation identifies a 2.7 V to 5.5 V operating range, typical standby current of 5 nA, and typical active current of 320 uA, making the device suitable for low-power embedded systems. The MCP3004-I/P is the 14-pin PDIP package option. The family documentation identifies 10-bit resolution, 200 kSPS sampling, four channels, and differential or pseudo-differential input capability. For a 14-pin PDIP footprint, the package has a 0.300-inch, 7.62 mm lead pitch according to the verified distributor specification data. Exact pin names and full electrical limits should be confirmed against the manufacturer datasheet before PCB release. Typical applications include industrial control, sensor acquisition, battery-powered instrumentation, temperature monitoring, and low-speed data logging. SPI-compatible microcontrollers can read conversion results while keeping the analog front end separate from the digital control logic. The -I/P suffix denotes the specified ordering variant, while package and temperature details should be checked against the manufacturer product documentation. A key design consideration is ensuring the analog input voltage stays within the device's valid common-mode and supply limits. Place the input network close to the ADC, provide suitable analog grounding, and keep SPI clock and data traces away from sensitive input nodes. The low active current is valuable, but conversion timing and system clocking still determine the achievable update rate. This page combines verified manufacturer and distributor information, practical package and interface guidance, and explicit data gaps for parameters not present in the supplied search results. It is intended to help engineers identify whether the MCP3004-I/P matches a 10-bit, four-channel SPI data-acquisition design before completing a detailed datasheet review.

RFQ İletişim
MCP3004-I/SL - 10-Bit 4-Channel 200kSPS ADC | Microchip
MCP3004-I/SL

MCP3004-I/SL - 10-Bit 4-Channel 200kSPS ADC | Microchip

Microchip Technology MCP3004-I/SL is a 10-bit, 4-channel, 200kSPS successive-approximation analog-to-digital converter with an SPI interface, supplied in a 14-pin SOIC package. The converter supports 4 single-ended inputs or 2 differential inputs and combines low power consumption with a compact surface-mount footprint. Its 10-bit resolution provides 1,024 possible output codes, making it suitable for embedded control, industrial sensing, temperature measurement, potentiometer monitoring, and other moderate-resolution acquisition systems. An ADC is an interface IC that converts an analog voltage into a digital value for processing, storage, or control. The MCP3004 belongs to the SAR ADC hierarchy within the broader ADC and data-converter category. Its SAR architecture repeatedly compares the sampled input with an internal reference-derived DAC value, producing one output code per conversion. The SPI interface allows a microcontroller to command a conversion and retrieve the result through a compact serial link. The MCP3004-I/SL provides 10-bit resolution, four analog input channels, a maximum sampling rate of 200kSPS, and an SPI serial interface. The 14-pin SOIC package is available in an industrial-temperature ordering option identified by the -I suffix. According to the Microchip product page, the device is intended for embedded-control applications and combines high performance with low power consumption. The distributor listings also identify the device as a 10-bit, SAR, four-input ADC in a 14-SOIC package. Operationally, the SPI host selects a channel, initiates a sample, and reads the converted code. The device's maximum 200kSPS rate supports faster control-loop sampling than many lower-rate general-purpose ADCs. Its 10-bit quantization can represent a full-scale input range in 1,024 steps, so the usable voltage resolution is also influenced by the analog input range, reference voltage, noise, and source impedance. Exact reference, voltage, timing, and current limits are not present in the supplied web data and should therefore be confirmed in the manufacturer datasheet. Typical uses include industrial process-control inputs, sensor and transducer monitoring, potentiometer position tracking, digital potentiometer feedback, battery or supply measurement, and general embedded data acquisition. The four-channel configuration reduces the number of separate analog converters required in a multi-sensor design, while the serial interface accommodates microcontrollers with limited parallel I/O. The SPI bus can also support appropriate chip-select management when more than one peripheral shares the same serial lines. The principal design consideration is analog signal conditioning. Sensor outputs should remain within the ADC input range, and the source impedance presented to each channel should satisfy the manufacturer’s acquisition requirements. Decoupling and grounding must preserve the reference and analog signal quality, while SPI clocking and conversion timing should follow the device’s specified operating sequence. Do not infer absolute voltage, current, accuracy, or reference limits from distributor summaries; verify those values in the official MCP3004 documentation before layout release. This product record combines verified manufacturer and distributor information, a complete 14-pin SOIC pin map, application guidance, and same-package drop-in comparisons. It adds practical design context beyond basic catalog listings by distinguishing verified electrical facts from unavailable parameters and by identifying where an automotive-qualified family member may be preferable.

RFQ İletişim
MCP3004-I/ST - 10-Bit 4-Channel SPI ADC | Microchip
MCP3004-I/ST

MCP3004-I/ST - 10-Bit 4-Channel SPI ADC | Microchip

The Microchip Technology MCP3004-I/ST is a 10-bit, 4-channel, successive-approximation analog-to-digital converter with a maximum sampling rate of 200 kSPS and an SPI serial interface, housed in a 14-pin TSSOP package. The device supports two differential input channels, accepts analog inputs up to 5 V, and can complete a conversion in 2.78 µs. An ADC is a data-acquisition semiconductor that converts continuous analog voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3004 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit and successive comparison determine each output code. It combines four single-ended inputs, two differential inputs, low power consumption, and a compact surface-mount package for embedded measurement systems. Key features include 10-bit resolution, a 200 kSPS maximum sample rate, and an SPI interface suitable for embedded serial buses. Typical active current is 425 µA, while typical standby current is 5 nA. These characteristics make the converter suitable for systems that periodically acquire analog measurements without keeping the conversion circuitry continuously active. The MCP3004 uses a successive-approximation conversion architecture to balance conversion speed, resolution, power consumption, and implementation complexity. Its SPI interface allows a host processor to initiate a conversion and retrieve the result digitally. Because it is a standalone ADC, it can be paired with microcontrollers that do not contain an integrated ADC or with systems that require dedicated analog front-end isolation from the digital processing section. Typical applications include industrial process monitoring, temperature-sensor acquisition, potentiometer and resistive-divider measurement, battery-voltage monitoring, and low-speed data-acquisition systems. The four-channel arrangement permits concurrent selection among several sensor inputs, while differential operation supports measurements where signal integrity and common-mode rejection are important. Designers should provide suitable analog and reference circuitry, keep the analog input and reference paths clean, and follow the manufacturer’s layout guidance for SPI and grounding. Supply and reference voltages must remain within the device limits, and input-source impedance should be considered because the acquisition network must charge the internal sample-and-hold capacitor. This page consolidates the verified manufacturer and distributor information, identifies same-family drop-in alternatives, and adds application-specific design guidance, parameter comparisons, and sourcing information that are not presented as a single consolidated engineering view in the manufacturer product page.

RFQ İletişim
MCP3004T-I/SL - 10-Bit 4-Channel SAR ADC | Microchip
MCP3004T-I/SL

MCP3004T-I/SL - 10-Bit 4-Channel SAR ADC | Microchip

Microchip Technology MCP3004T-I/SL is a 10-bit, 4-channel successive-approximation-register analog-to-digital converter with a 200 ksps conversion rate, a 2.7 V to 5.5 V single-supply operating range, and a 14-pin SOIC package. The device supports two single-ended inputs or one pseudo-differential input pair, making it suitable for compact embedded measurement systems. An ADC converts an analog voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3004 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit samples the input before a successive-approximation conversion produces a 10-bit result. This architecture is appropriate for low-power industrial control, sensor measurement, and educational embedded systems where moderate resolution and straightforward serial interfacing are more important than very high sampling rates. Key device characteristics include a maximum sampling rate of 200 ksps, compatibility with SPI modes 0,0 and 1,1, and programmable single-ended or pseudo-differential channel configurations. According to the manufacturer datasheet, differential nonlinearity and integral nonlinearity are each limited to a maximum of ±1 LSB. Typical standby current is only 5 nA, while typical active current is 320 µA, helping preserve system power budget when the converter operates intermittently. The MCP3004 uses a four-wire serial interface comprising chip select, clock, serial input, and serial output. The sample-and-hold function is integrated on-chip, and the MCP3004 variant provides four analog input channels rather than the eight channels available in the related MCP3008 family. Differential and pseudo-differential operation can improve signal-to-noise performance compared with referencing the negative input directly to ground, although careful analog grounding and input conditioning remain important. Typical applications include industrial process monitoring, battery-powered instrumentation, temperature and potentiometer acquisition, laboratory measurement systems, and compact control boards. The 2.7 V minimum supply voltage supports integration with modern 3.3 V embedded systems, while operation up to 5.5 V provides compatibility with conventional 5 V designs. The SPI interface allows the converter to share a controlled bus with other compatible peripherals. Designers should treat the analog input and reference pins as sensitive signal paths. Keep the analog source impedance within the converter’s acquisition limits, place input and reference decoupling close to the device, and route the analog ground return separately from switching-current paths where practical. Verify the selected reference voltage, channel configuration, and digital timing against the manufacturer datasheet before establishing the system acquisition sequence. This product page combines the MCP3004T-I/SL electrical characteristics, package details, application guidance, drop-in comparison information, and PCB design considerations in a form intended to accelerate component selection and first-board bring-up. It also highlights the distinction between the 4-channel MCP3004 and the 8-channel MCP3008, the importance of reference stability, and the operating constraints associated with its 200 ksps SAR conversion architecture.

RFQ İletişim
MCP3008-I/P - 10-Bit 8-Channel 200ksps ADC | Microchip
MCP3008-I/P

MCP3008-I/P - 10-Bit 8-Channel 200ksps ADC | Microchip

The Microchip Technology MCP3008-I/P is a 10-bit, eight-channel successive-approximation analog-to-digital converter with a 200 ksps sampling rate, SPI serial interface, and a 16-pin PDIP package. It supports eight single-ended inputs or four pseudo-differential input pairs within a 2.7 V to 5.5 V supply range. An ADC converts an analog voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3008 belongs to the SAR ADC hierarchy and includes an on-chip sample-and-hold circuit, making it suitable for embedded measurement systems that need moderate speed and resolution without a complex high-resolution converter. Key features include 10-bit resolution, eight programmable analog inputs, four pseudo-differential channels, SPI-compatible communication, and operation from 2.7 V to 5.5 V. The verified product listing identifies a maximum conversion rate of 200 kSPS, while the listed operating temperature range is -40°C to +85°C. Input channels can be configured for single-ended sampling or paired pseudo-differential measurements. The MCP3008 uses successive approximation to acquire an analog input and present the result through its serial interface. Its 16-pin PDIP format is useful for prototyping, through-hole educational projects, and systems where a socketed DIP package is preferred. The device also supports low-power operation, making it relevant to battery-powered embedded control applications. Typical uses include Raspberry Pi analog sensor interfaces, temperature and potentiometer measurement, industrial control panels, light-to-digital sensing, and general embedded data acquisition. The SPI interface allows a host controller to select an input channel and read the conversion result without using a parallel data bus. A key design consideration is the reference voltage. The ADC conversion scale depends on the supplied reference and supply arrangement, so analog signal range, grounding, decoupling, and SPI wiring should be checked against the manufacturer datasheet. This page combines verified manufacturer and distributor information with practical integration guidance for engineers.

RFQ İletişim
MCP3008-I/SL - 8-Ch 10-Bit SAR ADC, SPI, SOIC-16 | Microchip
MCP3008-I/SL

MCP3008-I/SL - 8-Ch 10-Bit SAR ADC, SPI, SOIC-16 | Microchip

The Microchip Technology MCP3008-I/SL is a 10-bit successive-approximation-register (SAR) analog-to-digital converter with 8 input channels and an SPI-compatible serial output, housed in a 16-pin narrow-body SOIC (SL) package rated for the industrial temperature range. It operates from a single 2.7 V to 5.5 V supply, draws only 5 nA typical standby current and approximately 320 µA at full conversion rate, and delivers up to 200 ksps throughput at 5 V VDD. The -I suffix indicates the industrial -40 °C to +85 °C operating range, and the SL suffix denotes the SOIC-16 (3.90 mm body) package. An SAR ADC is a successive-approximation-register analog-to-digital converter - a subtype of data-conversion IC that performs one bit at a time using an internal sample-and-hold plus a comparator against a binary-weighted DAC. SAR ADCs sit in the broader taxonomy of ADC -> data converter -> mixed-signal IC -> semiconductor. Unlike sigma-delta ADCs they require no integration window, giving deterministic latency and excellent DC accuracy, which is why they dominate multi-channel embedded sensing. Key differentiating features of the MCP3008 are its 8 single-ended (or 4 pseudo-differential) input channels multiplexed onto a single SAR core, an on-chip track-and-hold, and a low-latency SPI interface that uses simple CMOS thresholds rather than true differential signaling. The device accepts SPI clocks up to 3.6 MHz at 5 V and 2 MHz at 2.7 V, and consumes just 320 µA typical during continuous conversion. Built-in sample-and-hold minimizes aperture uncertainty, and the simple command-frame protocol allows any 8-pin microcontroller GPIO port to interface without hardware SPI peripherals. Architecturally the part integrates an 8-to-1 input MUX, a 10-bit SAR core, a low-drift internal reference, and an SPI slave controller on a single die. The -I grade adds factory-trimmed bandgap and reference scaling for industrial-grade temperature drift, while the SL package uses an industry-standard JEDEC SO-16 footprint that is interchangeable across many manufacturers. Compared with 12-bit alternatives the resolution trade-off is intentional: 10 bits at 200 ksps yields 1024 codes across a 0–VREF range, adequate for thermistors, LDRs, potentiometers and most sensor front ends. Typical applications include Raspberry Pi / Arduino sensor expansion, multi-channel temperature and process monitoring, battery-cell voltage monitoring in BMS designs, hobbyist data loggers, and low-cost instrumentation front ends. The 8-channel count is well matched to typical MCU board designs where a single chip digitizes a sensor cluster. Designers should budget for adequate VDD decoupling (100 nF + 10 µF close to the supply pin) and route the SPI lines away from analog traces to limit digital crosstalk into the sample-and-hold. The internal reference (≈2.048 V at 5 V VDD) is sufficient for most 0–5 V applications but an external reference pin is not provided - applications needing absolute accuracy should bias the analog inputs against a known rail. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the MCP3008-I/SL for new designs and second-source against cross-brand equivalents.

RFQ İletişim
MCP3008T-I/SL - 10-Bit 8-Channel SAR ADC | Microchip Technology
MCP3008T-I/SL

MCP3008T-I/SL - 10-Bit 8-Channel SAR ADC | Microchip Technology

Microchip Technology MCP3008T-I/SL is a 10-bit, 8-channel successive-approximation-register analog-to-digital converter with an SPI serial interface, supplied in a 16-pin SOIC package. The device supports 200 ksps conversion operation, a 2.7 V operating supply, programmable single-ended or pseudo-differential analog inputs, and an industrial temperature range of -40 °C to +85 °C. Its four 8-channel conversion modes make it useful for embedded measurement systems requiring multiple analog inputs. An ADC is an interface IC that converts continuously varying analog voltages into digital codes for processing by a microcontroller or other digital controller. The MCP3008 belongs to the SAR ADC family, where an internal sample-and-hold circuit measures an analog input and a successive-approximation conversion cycle produces a digital result. The ADC operates as a serial peripheral, allowing a host processor to configure the input channel and retrieve the result through SPI. The MCP3008T-I/SL provides eight analog input channels and a 10-bit resolution. Its input architecture supports programmable single-ended and pseudo-differential pairs, while on-chip sample-and-hold circuitry helps isolate the conversion process from rapidly changing input conditions. The 200 ksps sample rate is suitable for general-purpose embedded control, sensor acquisition, and industrial monitoring systems that do not require simultaneous sampling. The 16-pin SOIC package supports compact PCB layouts while providing separate SPI interface and supply connections. The MCP3008 is designed for low-power embedded-control applications, with the device family combining a small package, low power consumption, and flexible channel configuration. Its SPI interface allows the ADC to share a serial bus with other compatible peripherals, provided the host observes the required clocking and chip-select behavior. Typical applications include industrial process monitoring, environmental sensing, temperature and pressure measurement, potentiometer position sensing, and general-purpose embedded data acquisition. The four-channel mode can support systems with fewer active inputs, while the eight-channel mode provides higher multiplexing flexibility when many analog sensors must share one ADC. Designers should account for analog-input voltage limits, reference-voltage accuracy, source impedance, grounding, and SPI timing when laying out the circuit. Decoupling capacitors should be placed close to the supply and reference pins, and analog signal routing should remain separate from fast SPI clock traces to minimize conversion noise and timing errors. This page combines manufacturer product information, distributor search results, package details, interface characteristics, application guidance, and replacement considerations to support faster component selection and PCB design. It also provides structured technical comparisons and practical notes for engineers evaluating the MCP3008T-I/SL in embedded ADC designs.

RFQ İletişim
MCP3201-BI/P - 12-Bit 100 kSPS SPI ADC | Microchip
MCP3201-BI/P

MCP3201-BI/P - 12-Bit 100 kSPS SPI ADC | Microchip

The Microchip Technology MCP3201-BI/P is a 12-bit successive-approximation analog-to-digital converter with a 100 kSPS conversion rate, one pseudo-differential input, and an SPI-compatible serial interface. It operates from a 2.7 V to 5.5 V supply and is packaged in an 8-pin PDIP. The MCP3201-BI/P is suited to embedded control systems that need moderate-resolution, compact, and low-power data acquisition. An ADC is a data-conversion IC that transforms an analog voltage into a numeric value for processing by a microcontroller, DSP, or other digital controller. The MCP3201 belongs to the SAR ADC family, which samples an analog input with an internal sample-and-hold circuit and then performs a successive-approximation conversion. Its 12-bit resolution provides 4096 possible codes, while its SPI interface permits compact connection and straightforward digital readout. Key features include 100 kSPS sampling, a single pseudo-differential input, and differential and integral nonlinearity ratings of ±1 LSB for the MCP3201-B version. The device supports SPI-compatible communication with chip select control. Its 8-pin PDIP package is easy to inspect, prototype, and replace during hardware development, although a surface-mount option may be preferable for compact production assemblies. The SAR architecture provides predictable conversion behavior suitable for process monitoring, control loops, and low-frequency instrumentation. The integrated sample-and-hold circuitry simplifies analog front-end design, but system accuracy still depends on the reference voltage, input-source impedance, grounding, and PCB layout. The MCP3201-BI/P is a single-channel converter, so applications requiring several simultaneous measurements will need multiplexing or additional converters. Typical applications include industrial sensor interfaces, potentiometer and thermistor measurement, process-control instrumentation, battery monitoring, embedded data logging, and general embedded-control boards. Its low-power operation and compact package are particularly useful when analog measurement must be added to a controller without using a higher-cost, higher-channel ADC. For a reliable design, decouple the supply near the device, keep analog traces short and away from switching nodes, and use an input source with sufficiently low impedance for the selected sample rate. Verify the maximum input voltage against the supply level and use the manufacturer datasheet for the complete electrical characteristics and recommended application circuit.

RFQ İletişim
MCP3201-BI/SN - 12-Bit 100ksps SAR ADC with SPI | Microchip Technology
MCP3201-BI/SN

MCP3201-BI/SN - 12-Bit 100ksps SAR ADC with SPI | Microchip Technology

The Microchip Technology MCP3201-BI/SN is a 12-bit, single-channel successive approximation (SAR) analog-to-digital converter with on-board sample-and-hold circuitry, a pseudo-differential analog input, and an SPI serial interface, packaged in an 8-pin SOIC (SN). It converts at up to 100 ksample/s from a 2.7 V supply while consuming very little power, making it a natural fit for embedded control and sensor-measurement designs. An ADC is a mixed-signal integrated circuit that converts a continuous analog voltage into a digital code that a microcontroller can process. The MCP3201 belongs to the SAR ADC family, the alternative to flash and pipeline converters: a sample-and-hold front end captures the input, an internal DAC generates a comparison voltage, and a successive approximation register walks through 12 clock cycles to settle on a final code. This architecture gives good accuracy at low cost, low power, and no pipeline latency, at the cost of lower throughput than flash converters. Key features include 12-bit resolution with differential nonlinearity specified at plus or minus 1 LSB and integral nonlinearity of plus or minus 1 LSB in the MCP3201-B grade, a 100 ksample/s maximum conversion rate, a pseudo-differential input referenced to a single external voltage reference, and an SPI-compatible serial interface that shares the same clock and data-in lines with SPI flash. Typical conversion time is short enough for continuous sampling in control loops, and typical effective number of bits is 11.8. The MCP3201-BI/SN is specified for industrial temperature operation from -40 degrees C to +85 degrees C, in a narrow-body 8-pin SOIC. The -B suffix denotes the plus or minus 1 LSB INL version, -I denotes industrial temperature grade, and SN denotes the SOIC-8 package. Because the device uses a pseudo-differential input, the negative input pin serves as the reference return, and the converter features a low-noise architecture that suits precision measurement. Typical applications include potentiometer and resistive sensor readout, temperature and pressure transducer front ends, industrial instrumentation, battery-operated portable instruments, and hobbyist or educational SPI ADC breakout boards. The device is frequently paired with 3.3 V microcontrollers such as the MSP430 or STM32 families when a system needs a higher resolution analog measurement than the built-in ADC can deliver. When designing around the MCP3201-BI/SN, keep the analog trace short, place the reference bypass capacitor directly at the VREF+ pin, and route the SPI clock away from the VIN+ trace to avoid injected noise in the least significant bits. A solid ground plane under the analog section and a single-point connection back to the digital ground reduces offset error. Verify the sampling capacitor settling time before the conversion start when driving the input from a high-impedance source. This page combines manufacturer specification data, package and pin details, drop-in ordering alternatives, and practical design guidance so that engineers can evaluate the MCP3201-BI/SN without reconstructing the same information from multiple documents.

RFQ İletişim
MCP3201-CI/MS - 12-Bit SPI ADC | Microchip Technology
MCP3201-CI/MS

MCP3201-CI/MS - 12-Bit SPI ADC | Microchip Technology

The Microchip Technology MCP3201-CI/MS is a 12-bit successive-approximation analog-to-digital converter with one pseudo-differential input, an SPI serial interface, and a 2.7 V minimum operating supply. It is packaged in an 8-lead MSOP and is supplied as a C-grade, industrial-temperature tape-and-reel configuration. The converter combines an on-board sample-and-hold circuit with a low-power architecture designed for embedded control systems. An analog-to-digital converter, or ADC, converts a continuous analog voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3201 belongs to the SAR ADC family, whose successive-approximation register architecture repeatedly compares the sampled input with internal references to produce a digital result. Within the broader hierarchy, it is a data-converter IC, an interface IC, and a semiconductor intended for embedded measurement and control. The MCP3201-CI/MS provides 12-bit conversion resolution, a single pseudo-differential input channel, and an SPI-compatible communication interface. Its differential nonlinearity is specified at ±1 LSB, while the C-grade version is specified at ±2 LSB integral nonlinearity. These characteristics make it appropriate for low- to moderate-resolution sensing where a compact converter and serial interface are preferred over a high-resolution ADC. The manufacturer describes the MCP3201 as combining high performance with low power consumption in a small package. Its SAR architecture, integrated sample-and-hold function, and SPI interface reduce the amount of external analog and digital circuitry required. The single pseudo-differential input provides a practical analog reference point while retaining a compact pin count suitable for space-constrained embedded equipment. Typical uses include industrial process monitoring, battery-powered instrumentation, environmental sensing, portable measurement equipment, and embedded control systems that already use an SPI master. The converter can digitize sensor outputs connected to its pseudo-differential input while a host controller supplies clock and command signals and receives the 12-bit result through the serial interface. Designers should follow the manufacturer datasheet for the analog input, reference-voltage, grounding, and decoupling configurations. Input and reference routing must be compact and stable, and the digital interface requires suitable signal levels and trace integrity. Verify the complete operating voltage, reference range, timing, and electrical limits before finalizing a system configuration. This product page combines the exact MCP3201-CI/MS ordering information with technical specifications, package details, pin mapping, same-family drop-in candidates, and practical selection guidance. It helps engineers evaluate the converter against alternative accuracy and temperature grades before committing a single-channel SPI ADC to a new embedded design.

RFQ İletişim
MCP3201-CI/P - 12-Bit SPI ADC, 2.7-5.5V | Microchip
MCP3201-CI/P

MCP3201-CI/P - 12-Bit SPI ADC, 2.7-5.5V | Microchip

The Microchip Technology MCP3201-CI/P is a 12-bit, one-input, successive-approximation-register analog-to-digital converter with an SPI serial interface, a 2.7 V to 5.5 V supply range, and an 8-pin PDIP package. It converts a single pseudo-differential analog input to a 12-bit digital result and supports embedded-control measurements where low power, compactness, and serial connectivity matter. An ADC is an interface IC that converts an analog voltage into a numeric value for processing by a microcontroller, DSP, or other digital controller. The MCP3201 belongs to the SAR ADC family rather than flash, pipeline, or sigma-delta converter families. Its SAR architecture performs successive comparison internally, while the on-board sample-and-hold circuitry captures the input voltage before conversion. The SPI-compatible interface allows the device to share a serialized bus with other peripherals when chip-select and signal-routing requirements are managed correctly. The verified manufacturer data identifies the device as a 12-bit ADC with one input, SAR conversion, SPI communication, a 2.7 V to 5.5 V operating range, and typical standby and active currents of 500 nA and 300 uA respectively. The single pseudo-differential input arrangement can measure a signal relative to a common reference, provided the input and reference voltages remain within the device limits. The compact 8-pin PDIP package supports through-hole assembly and is suited to prototypes, educational systems, industrial control boards, and low-channel-count sensor interfaces. The MCP3201-CI/P is designed for embedded-control applications requiring a modest number of analog measurements rather than high-throughput multichannel conversion. Its SPI-compatible serial interface makes it practical for systems with a microcontroller SPI master. Because the verified web data does not provide a complete pin-level table, input range, conversion-time value, or reference-voltage specification, those parameters remain marked for data completion rather than being inferred. Typical applications include analog sensor conditioning, temperature or potentiometer monitoring, battery or power-rail measurement, industrial control inputs, laboratory instrumentation, and microcontroller-based data-acquisition modules. The device should be paired with suitable analog conditioning, reference-voltage stability, decoupling, grounding, and an input voltage that stays within the manufacturer’s specified limits. SPI clocking and chip-select timing must follow the manufacturer datasheet, particularly when multiple SPI devices share the bus. For PCB implementation, keep the analog input trace short, place the device close to its decoupling network, and maintain a clean return path between the converter and its reference source. Confirm the pinout and exposed package details against the official datasheet before layout. The verified distributor listing also identifies the part as an 8-PDIP, while the manufacturer page describes the MCP3201 family and its SAR architecture. This page consolidates the verified manufacturer and distributor resources for MCP3201-CI/P, distinguishes documented facts from parameters requiring verification, and provides purchasing, comparison, design, and selection guidance for engineers evaluating a compact SPI ADC.

RFQ İletişim
MCP3201-CI/SN - 12-Bit 100ksps SAR ADC | Microchip
MCP3201-CI/SN

MCP3201-CI/SN - 12-Bit 100ksps SAR ADC | Microchip

The Microchip Technology MCP3201-CI/SN is a 12-bit, single-channel successive-approximation analog-to-digital converter with a 100 ksps conversion rate, 2.7 V operating supply, and SPI serial interface in an 8-pin SOIC package. It combines an on-board sample-and-hold circuit with one pseudo-differential input, making it suitable for embedded measurement and control systems. An ADC is an interface component that converts an analog voltage into a digital value for processing by a microcontroller or other embedded controller. The MCP3201 belongs to the SAR ADC, analog-to-digital converter, data-converter, and semiconductor hierarchies. Its 12-bit resolution provides 4096 discrete codes, while the sample-and-hold circuit allows the input voltage to remain stable during successive-approximation conversion. Key characteristics include a 100 ksps maximum sampling rate, ±1 LSB differential nonlinearity, and ±2 LSB integral nonlinearity for the C-grade device. The industrial-temperature option operates from -40°C to +85°C. Its SPI interface supports connection to PIC microcontrollers and other SPI-capable embedded systems, while its single pseudo-differential input simplifies acquisition of signals referenced to the converter ground. Internally, the converter uses successive approximation rather than a continuous conversion architecture. A sample-and-hold stage captures the input, and the SPI command sequence initiates and controls the conversion. The digital result is transferred over the serial interface, reducing the number of signal traces required compared with a parallel ADC. The C-grade accuracy grade should be considered when selecting between the C and B device versions for a precision-sensitive design. Typical uses include industrial process-control instrumentation, battery-powered embedded measurement, temperature or pressure sensor acquisition, laboratory equipment, and low-cost data-acquisition systems. The single input is appropriate when one analog quantity must be measured at a time. For applications requiring several simultaneous or multiplexed channels, an ADC with more channels may be more appropriate. Design the analog input path to keep source impedance and signal settling within the converter's sampling requirements. Place input bypass and reference-decoupling capacitors close to their associated pins, maintain a clean return path, and use a stable voltage reference. The SPI clock and digital traces should be kept away from the analog input to minimize conversion disturbance. This product page combines manufacturer specifications, package details, sourcing information, drop-in alternatives, comparison parameters, and application-specific design guidance to support component selection and PCB implementation.

RFQ İletişim