Mikrodenetleyiciler

Ürünler (20.000+)

ATXMEGA64D4-MH - 32MHz AVR XMEGA 64KB MCU | Microchip
ATXMEGA64D4-MH

ATXMEGA64D4-MH - 32MHz AVR XMEGA 64KB MCU | Microchip

The Microchip Technology ATXMEGA64D4-MH is a low-power 8/16-bit AVR XMEGA D4 microcontroller with a 32 MHz clock, 64 KB flash memory, 2 KB EEPROM, 4 KB SRAM, and a 44-pin VQFN package measuring 7 x 7 mm. It combines read-while-write in-system programmable flash with a peripheral set designed for compact embedded control, communications, timing, and signal-processing systems. An AVR XMEGA microcontroller is an 8/16-bit embedded-processing device built around the enhanced AVR RISC architecture. Unlike a general-purpose microprocessor, it integrates flash memory, SRAM, EEPROM, interrupt control, timers, serial interfaces, and analog peripherals into one low-power component. The ATXMEGA64D4 family provides deterministic event handling and flexible timer resources for applications that need more control capability than a basic 8-bit MCU without moving to a more complex processor architecture. Key device features include 64 KB of ISP flash with read-while-write operation, 2 KB of EEPROM, and 4 KB of SRAM. The four-channel event system, programmable multilevel interrupt controller, 34 general-purpose I/O lines, and four flexible 16-bit timer/counters support responsive control tasks. Two USARTs and two two-wire serial interfaces provide multiple options for external sensors, displays, data acquisition equipment, and industrial communications links. The device operates from 1.6 V to 3.6 V and includes a 16-bit real-time counter with separate and combined 32-bit counters. Its four timer/counter modules include compare and PWM channels, while the event system can route signals between peripherals without excessive interrupt-service overhead. These characteristics support simultaneous sensing, timing, communications, and actuator-control functions within one compact package. Typical uses include industrial control modules, sensor-hub boards, data loggers, motor-control peripherals, building-automation interfaces, communications equipment, and compact test-and-measurement products. The 44-VQFN footprint is particularly useful when board area is constrained, although its fine pitch requires careful PCB assembly and exposed-pad thermal management. For a new design, route the VQFN exposed pad to a properly sized ground plane, place decoupling capacitors close to the supply pins, and confirm the board footprint against the manufacturer pinout drawing. Firmware should use the documented XMEGA clock, event-system, timer, and USART configuration registers. Because no explicit programming-voltage or clock-configuration values are listed on the product page, use the device data sheet and selected programming tool documentation before finalizing board and firmware settings. This product page organizes the core MCU specifications, same-package alternatives, application guidance, and design considerations into a selection-focused reference. It also distinguishes verified product attributes from unresolved details so engineers can evaluate the ATXMEGA64D4-MH against other AVR XMEGA D4 choices before committing a board or production BOM.

RFQ İletişim
ATXMEGA8E5-AN - 32MHz 8KB AVR Microcontroller | Microchip
ATXMEGA8E5-AN

ATXMEGA8E5-AN - 32MHz 8KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA8E5-AN is a low-power, high-performance 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 8 KB flash memory, 512 bytes EEPROM, 1 KB SRAM, and eight-channel event-system support, housed in a 32-pin TQFP package. The -AN suffix identifies the specified Microchip ordering configuration, while the family datasheet is titled ATxmega32E5/16E5/8E5 Data Sheet. A microcontroller is a programmable embedded-control IC that integrates a processor core, memory, timers, communication interfaces, and peripherals on one device. The AVR XMEGA E5 belongs to the 8/16-bit AVR enhanced RISC microcontroller family, combining low-power operation with event-driven control and read-while-write flash support. This makes it useful for compact control systems that need deterministic timing and flexible peripheral interconnection. The ATXMEGA8E5-AN combines 8 KB ISP flash with an additional 2 KB boot-code section, 512 bytes EEPROM, and 1 KB SRAM. Its operating supply range is listed by Mouser as 1.6 V to 3.6 V, with an operating-temperature marking of 105C. The family documentation identifies a 32-pin device configuration, while the distributor listings identify this exact orderable part as ATXMEGA8E5-AN in a 32-TQFP package. The ATXMEGA family is intended for applications where compact code execution, EEPROM retention, and event-system peripherals are valuable. The eight-channel event system is a key architectural feature. It allows hardware peripherals and external signals to communicate through event resources, reducing the need for polling and helping coordinate timing-sensitive tasks. The integrated memory arrangement also supports firmware storage, boot loading, and working data in a single controller. Compared with a larger general-purpose MCU, the ATXMEGA8E5-AN offers a focused 8/16-bit platform with a small memory footprint and a 32 MHz clock. Typical uses include industrial automation, sensor and actuator control, compact embedded instruments, motor-control support, communication-interface designs, and low-power control nodes. The exact peripheral mix, electrical limits, programming requirements, and package pin details should be confirmed against the Microchip family datasheet and the ATXMEGA8E5-AN ordering information before final PCB release. Designers should preserve the required decoupling, oscillator layout, programming access, and unused-pin treatment recommended by the manufacturer. Firmware should be built for the ATxmega8E5 device definition and validated with the intended clock source and supply voltage. Because this page is assembled from distributor listings and the family datasheet, package suffixes and purchasing conditions should be checked against the latest authorized source. This page combines verified distributor specifications, the official Microchip product description, family datasheet information, application guidance, and sourcing links to support component selection and engineering review.

RFQ İletişim
ATXMEGA8E5-ANR - 32MHz 8KB AVR Microcontroller | Microchip (Tape & Reel)
ATXMEGA8E5-ANR

ATXMEGA8E5-ANR - 32MHz 8KB AVR Microcontroller | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA8E5-ANR is a low-power, high-performance 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 8 KB flash memory, 512 bytes EEPROM, 1 KB SRAM, and eight-channel event-system support, housed in a 32-pin TQFP package. The -AN suffix identifies the specified Microchip ordering configuration, while the family datasheet is titled ATxmega32E5/16E5/8E5 Data Sheet. A microcontroller is a programmable embedded-control IC that integrates a processor core, memory, timers, communication interfaces, and peripherals on one device. The AVR XMEGA E5 belongs to the 8/16-bit AVR enhanced RISC microcontroller family, combining low-power operation with event-driven control and read-while-write flash support. This makes it useful for compact control systems that need deterministic timing and flexible peripheral interconnection. The ATXMEGA8E5-ANR combines 8 KB ISP flash with an additional 2 KB boot-code section, 512 bytes EEPROM, and 1 KB SRAM. Its operating supply range is listed by Mouser as 1.6 V to 3.6 V, with an operating-temperature marking of 105C. The family documentation identifies a 32-pin device configuration, while the distributor listings identify this exact orderable part as ATXMEGA8E5-ANR in a 32-TQFP package. The ATXMEGA family is intended for applications where compact code execution, EEPROM retention, and event-system peripherals are valuable. The eight-channel event system is a key architectural feature. It allows hardware peripherals and external signals to communicate through event resources, reducing the need for polling and helping coordinate timing-sensitive tasks. The integrated memory arrangement also supports firmware storage, boot loading, and working data in a single controller. Compared with a larger general-purpose MCU, the ATXMEGA8E5-ANR offers a focused 8/16-bit platform with a small memory footprint and a 32 MHz clock. Typical uses include industrial automation, sensor and actuator control, compact embedded instruments, motor-control support, communication-interface designs, and low-power control nodes. The exact peripheral mix, electrical limits, programming requirements, and package pin details should be confirmed against the Microchip family datasheet and the ATXMEGA8E5-ANR ordering information before final PCB release. Designers should preserve the required decoupling, oscillator layout, programming access, and unused-pin treatment recommended by the manufacturer. Firmware should be built for the ATxmega8E5 device definition and validated with the intended clock source and supply voltage. Because this page is assembled from distributor listings and the family datasheet, package suffixes and purchasing conditions should be checked against the latest authorized source. This page combines verified distributor specifications, the official Microchip product description, family datasheet information, application guidance, and sourcing links to support component selection and engineering review.

RFQ İletişim
ATXMEGA8E5-AU - 32MHz 8KB AVR MCU | Microchip Technology
ATXMEGA8E5-AU

ATXMEGA8E5-AU - 32MHz 8KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA8E5-AU is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum operating frequency, 8 KB of ISP Flash memory, and a 32-pin TQFP package measuring 7 mm × 7 mm. It operates from 1.6 V to 3.6 V and is supplied in an industrial-temperature, green package configuration. An AVR XMEGA microcontroller is a compact embedded-control device that combines a CPU core, flash program memory, SRAM, EEPROM, timers, communication peripherals, and event-system hardware on one integrated circuit. The ATXMEGA8E5 belongs to the low-power, high-performance XMEGA E5 family, where the enhanced RISC architecture supports deterministic embedded processing for control, sensing, communications, and low-energy products. The device provides 8 KB of ISP Flash organized as 4K × 16, plus a 2 KB boot-code section with read-while-write capabilities. Its memory resources include 512 bytes of EEPROM and 1 KB of SRAM. An eight-channel event system connects peripherals without requiring continuous CPU intervention, while a programmable multi-level interrupt system supports event-driven firmware designs. A maximum clock frequency of 32 MHz provides additional performance headroom for compact control tasks. The ATXMEGA8E5-AU is intended for embedded systems that need deterministic peripheral interaction, efficient local storage, and a compact surface-mount footprint. Potential uses include industrial control modules, low-power sensor nodes, compact motor-control subsystems, building automation, instrumentation, and compact consumer accessories. The 1.6 V minimum operating voltage also makes the device suitable for systems designed around low-voltage energy-storage or sensor-power rails. Designers should pay attention to the 1.6 V to 3.6 V supply range, available 1 KB SRAM, and the division between 8 KB general Flash and the 2 KB boot section. Firmware size and interrupt-heavy workloads should be checked against the limited SRAM. Decoupling, clock stability, programming access, and exposed-pad or via-in-pad land patterns should be reviewed against the complete manufacturer data sheet before layout release. This page consolidates the verified manufacturer and distributor specifications, focused drop-in comparison data, and practical engineering guidance for the ATXMEGA8E5-AU. It also distinguishes verified electrical and packaging facts from parameters that require confirmation in the complete Microchip documentation.

RFQ İletişim
ATXMEGA8E5-AUR - 32MHz 8KB AVR Microcontroller | Microchip Technology
ATXMEGA8E5-AUR

ATXMEGA8E5-AUR - 32MHz 8KB AVR Microcontroller | Microchip Technology

The Microchip Technology ATXMEGA8E5-AUR is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum operating frequency, 8 KB of flash memory, and a 32-pin TQFP package measuring 7 mm by 7 mm. It combines 1 KB of SRAM, 512 bytes of EEPROM, and a 2 KB boot section with a low-power, peripheral-rich architecture designed for embedded control applications. An 8/16-bit microcontroller is a programmable semiconductor that executes firmware, reads sensors, controls outputs, and manages communication interfaces. The AVR XMEGA family uses an enhanced RISC architecture and provides dedicated event-system hardware, timers, serial interfaces, and analog peripherals. Within the broader hierarchy of embedded semiconductors, the ATXMEGA8E5-AUR is a microcontroller with integrated nonvolatile memory and mixed-signal peripherals rather than a general-purpose processor or discrete logic device. The principal features include 32 MHz operation, 8 KB of in-system self-programmable flash with read-while-write capability, 1 KB of SRAM, 512 bytes of EEPROM, and an eight-channel event system. A programmable multi-level interrupt controller supports deterministic event handling, while the operating-voltage range of 1.6 V to 3.6 V supports low-voltage embedded systems. The device also provides the peripheral resources typical of an industrial-oriented XMEGA E5 design. The ATxmega E5 architecture combines a high-performance AVR core with dedicated hardware for timers, communications, and event routing. Its event system can connect multiple peripheral events without requiring continuous central-processor polling, helping reduce interrupt overhead in control loops. Flash memory supports in-system programming, and the dedicated boot section allows firmware to reserve space for application startup or field-update routines. The 32-pin TQFP package exposes the GPIO, power, ground, reset, clock, and analog-reference connections required by the family device. Typical uses include industrial sensor nodes, compact motor-control modules, building-automation controllers, instrumentation peripherals, low-power monitoring equipment, and embedded communication gateways. The combination of 8 KB flash, 1 KB SRAM, and an event system is useful when a compact control product requires deterministic peripheral interactions without the memory overhead of a larger application processor. Designers should budget flash and SRAM carefully because the ATXMEGA8E5-AUR is optimized for compact control tasks rather than large graphical or network-heavy workloads. External decoupling, careful clock routing, and a stable reference design remain important at 32 MHz. The 32-pin TQFP footprint also requires a PCB layout that provides adequate copper access around the exposed leads. This product page combines the manufacturer’s technical specifications, pin-package guidance, verified source links, and application-focused design guidance. It also explains the limitations of currently confirmed replacement parts so engineers can distinguish a true same-footprint option from a device that merely belongs to the same AVR family.

RFQ İletişim
ATXMEGA8E5-M4U - 32MHz 8KB AVR MCU | Microchip Technology
ATXMEGA8E5-M4U

ATXMEGA8E5-M4U - 32MHz 8KB AVR MCU | Microchip Technology

Microchip Technology ATXMEGA8E5-M4U is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 8 KB of flash program memory, 1 KB of SRAM, and 512 B of EEPROM in a 32-UQFN 4 x 4 mm package. It operates from a 1.6 V to 3.6 V supply and includes an ADC plus I2C, IrDA, SPI, and UART/USART connectivity. The -M4U ordering code identifies the compact 32-UQFN package variant, while the verified distribution data identifies the device as factory programmable. An 8/16-bit microcontroller is a semiconductor that combines a programmable processor core, nonvolatile program memory, volatile working memory, and integrated peripherals on one device. The AVR enhanced RISC architecture belongs to the MCU hierarchy: microcontroller > integrated circuit > semiconductor. XMEGA E5 devices are designed for low-power, high-performance embedded control where local timing, serial communication, and mixed-signal measurement can be combined without requiring a separate processor. The ATXMEGA8E5 combines 8 KB ISP flash with read-while-write capability, a separate 2 KB boot-code area, 1 KB SRAM, and 512 B EEPROM. Its eight-channel event system and programmable multi-level interrupt capability support deterministic responses to timing events. A 32 MHz operating limit provides higher execution bandwidth than many entry-level 8-bit MCUs while preserving the familiar AVR instruction set and development ecosystem. The E5 family combines an 8/16-bit core with communication peripherals including I2C, SPI, UART/USART, and IrDA. An on-chip ADC is present according to the verified product listing. This integration reduces external component count in compact control nodes, particularly when the design needs several serial buses, nonvolatile data storage, and periodic analog measurement in a small board area. Typical applications include compact industrial controllers, sensor-interface modules, building-control endpoints, communication bridges, low-power data loggers, and embedded peripherals that need mixed-signal measurement. The 1.6 V to 3.6 V operating range makes the device suitable for low-voltage embedded systems, while the small 4 x 4 mm package supports space-constrained portable and distributed-control products. Designers should verify the exact pin functions, exposed-pad requirements, clock configuration, and decoupling recommendations in the manufacturer datasheet before layout. The verified source identifies the device as factory programmable, so production programmers must also account for Microchip's device-specific programming and configuration requirements rather than assuming a generic ISP workflow alone is sufficient. This page consolidates the verified ATXMEGA8E5-M4U specifications, current distributor availability, package information, procurement data, and qualification limits for engineering review. It also separates confirmed drop-in alternatives from related XMEGA E5 devices whose memory configuration or package code may prevent a literal drop-in replacement.

RFQ İletişim
ATXMEGA8E5-MN - 32MHz 8KB AVR Microcontroller | Microchip
ATXMEGA8E5-MN

ATXMEGA8E5-MN - 32MHz 8KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA8E5-MN is a low-power 8/16-bit AVR XMEGA microcontroller with a 32 MHz clock, 8 KB flash memory, 512 bytes of EEPROM, 1 KB SRAM, and a 32-pin 5 x 5 mm QFN package. The -MN ordering identifies the manufacturer-specified package and temperature variant. Its operating supply range is 1.6 V to 3.6 V, making it appropriate for compact embedded systems that need deterministic control, event-based peripherals, and low-power operation. A microcontroller is a programmable integrated circuit that combines a processor core, memory, and peripherals in one embedded device. The AVR XMEGA family sits within the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Compared with a general-purpose host processor, the ATXMEGA8E5-MN is intended for real-time control, sensor conditioning, communications, and compact control systems where deterministic execution and low power consumption matter more than desktop-class performance. Verified manufacturer information identifies 8 KB of ISP flash with read-while-write capability, a separate 2 KB boot-code section, 512 bytes of EEPROM, 1 KB of SRAM, and an eight-channel event system. The 8/16-bit AVR architecture and 32 MHz operating frequency provide a capable control platform without requiring a large external memory system. The device also offers programmable multi-level interrupt handling according to the manufacturer product-page snippet. The QFN package supports compact PCB layouts but requires careful land-pattern, thermal-pad, paste, and assembly planning. The QFN package is associated with surface-mount assembly rather than through-hole insertion, so the footprint, exposed thermal pad, solder mask, and manufacturing process must match the selected package variant. Exact pin names, electrical limits, peripheral channels, and timing values that were not supplied in the verified data are not inferred here. Typical application roles include compact industrial controllers, low-power sensor nodes, motor and actuator control, communications equipment, and embedded control modules. The ATXMEGA8E5-MN is best suited when the system needs AVR firmware compatibility, modest flash and SRAM capacity, EEPROM retention, and event-driven control rather than high-speed networking or large application workloads. Before finalizing a design, verify the complete manufacturer datasheet for pin assignments, clock requirements, peripheral availability, programming mode, absolute maximum ratings, and package-specific land geometry. The ATXMEGA8E5-MN is a leaded-free, green-compatible ordering option according to the distributor result, but full environmental and automotive qualification claims require confirmation from the manufacturer documentation.

RFQ İletişim
ATXMEGA8E5-MNR - 32MHz 8KB AVR Microcontroller | Microchip (Tape & Reel)
ATXMEGA8E5-MNR

ATXMEGA8E5-MNR - 32MHz 8KB AVR Microcontroller | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA8E5-MNR is a low-power 8/16-bit AVR XMEGA microcontroller with a 32 MHz clock, 8 KB flash memory, 512 bytes of EEPROM, 1 KB SRAM, and a 32-pin 5 x 5 mm QFN package. The -MN ordering identifies the manufacturer-specified package and temperature variant. Its operating supply range is 1.6 V to 3.6 V, making it appropriate for compact embedded systems that need deterministic control, event-based peripherals, and low-power operation. A microcontroller is a programmable integrated circuit that combines a processor core, memory, and peripherals in one embedded device. The AVR XMEGA family sits within the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Compared with a general-purpose host processor, the ATXMEGA8E5-MNR is intended for real-time control, sensor conditioning, communications, and compact control systems where deterministic execution and low power consumption matter more than desktop-class performance. Verified manufacturer information identifies 8 KB of ISP flash with read-while-write capability, a separate 2 KB boot-code section, 512 bytes of EEPROM, 1 KB of SRAM, and an eight-channel event system. The 8/16-bit AVR architecture and 32 MHz operating frequency provide a capable control platform without requiring a large external memory system. The device also offers programmable multi-level interrupt handling according to the manufacturer product-page snippet. The QFN package supports compact PCB layouts but requires careful land-pattern, thermal-pad, paste, and assembly planning. The QFN package is associated with surface-mount assembly rather than through-hole insertion, so the footprint, exposed thermal pad, solder mask, and manufacturing process must match the selected package variant. Exact pin names, electrical limits, peripheral channels, and timing values that were not supplied in the verified data are not inferred here. Typical application roles include compact industrial controllers, low-power sensor nodes, motor and actuator control, communications equipment, and embedded control modules. The ATXMEGA8E5-MNR is best suited when the system needs AVR firmware compatibility, modest flash and SRAM capacity, EEPROM retention, and event-driven control rather than high-speed networking or large application workloads. Before finalizing a design, verify the complete manufacturer datasheet for pin assignments, clock requirements, peripheral availability, programming mode, absolute maximum ratings, and package-specific land geometry. The ATXMEGA8E5-MNR is a leaded-free, green-compatible ordering option according to the distributor result, but full environmental and automotive qualification claims require confirmation from the manufacturer documentation.

RFQ İletişim
ATXMEGA8E5-MU - 32MHz 8KB Flash 32-QFN Microcontroller | Microchip
ATXMEGA8E5-MU

ATXMEGA8E5-MU - 32MHz 8KB Flash 32-QFN Microcontroller | Microchip

The Microchip Technology ATXMEGA8E5-MU is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 8 KB in-system programmable Flash, 1 KB SRAM, and 512 bytes of EEPROM in a 32-QFN 5x5 mm package. It also includes an eight-channel event system and programmable multi-level interrupt support for responsive peripheral control. A microcontroller is a programmable integrated circuit that combines a CPU core, nonvolatile program memory, working memory, and peripherals on one die. Within the semiconductor hierarchy, the ATXMEGA8E5 belongs to the 8/16-bit microcontroller class and uses the AVR enhanced RISC architecture. It is suited to compact embedded-control systems that require deterministic timing, flexible event handling, and low-power operation without a separate external memory interface. Key features include 8 KB of self-programmable Flash plus a 2 KB boot-code section, 1 KB of SRAM, 512 bytes of EEPROM, read-while-write capability, and operation up to 32 MHz. The 32-QFN package supports compact surface-mount layouts while providing the pin count associated with the XMEGA E5 family's peripheral-rich 32-pin devices. The family is also supported by the manufacturer product page and family data sheet. Technically, the device combines a high-performance 8/16-bit AVR processor with dedicated event-system and interrupt resources. The event system allows peripherals to trigger actions without relying on software polling, which can reduce CPU latency in timing-sensitive designs. Its boot section supports in-system self-programming, while the EEPROM provides nonvolatile parameter storage separate from program Flash. Typical uses include compact industrial controllers, low-power sensor nodes, embedded timing modules, communication peripherals, and consumer-control products. Designers should select external decoupling, clock, and programming support according to the manufacturer data sheet, and verify every board-level signal against the package pinout before layout release. A key design consideration is the limited 8 KB Flash and 1 KB SRAM budget. Firmware and buffers should be sized conservatively, while avoiding blocking delays in event-driven control loops. The device is also available in a TQFP form, so package suffix and land pattern must not be interchanged. This page consolidates verified manufacturer and distributor information, purchase-oriented pricing, and application-specific engineering guidance so engineers can assess the ATXMEGA8E5-MU before committing a PCB layout.

RFQ İletişim
ATXMEGA8E5-MUR - 32MHz 8KB Flash 32-QFN Microcontroller | Microchip (Tape & Reel)
ATXMEGA8E5-MUR

ATXMEGA8E5-MUR - 32MHz 8KB Flash 32-QFN Microcontroller | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA8E5-MUR is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 8 KB in-system programmable Flash, 1 KB SRAM, and 512 bytes of EEPROM in a 32-QFN 5x5 mm package. It also includes an eight-channel event system and programmable multi-level interrupt support for responsive peripheral control. A microcontroller is a programmable integrated circuit that combines a CPU core, nonvolatile program memory, working memory, and peripherals on one die. Within the semiconductor hierarchy, the ATXMEGA8E5 belongs to the 8/16-bit microcontroller class and uses the AVR enhanced RISC architecture. It is suited to compact embedded-control systems that require deterministic timing, flexible event handling, and low-power operation without a separate external memory interface. Key features include 8 KB of self-programmable Flash plus a 2 KB boot-code section, 1 KB of SRAM, 512 bytes of EEPROM, read-while-write capability, and operation up to 32 MHz. The 32-QFN package supports compact surface-mount layouts while providing the pin count associated with the XMEGA E5 family's peripheral-rich 32-pin devices. The family is also supported by the manufacturer product page and family data sheet. Technically, the device combines a high-performance 8/16-bit AVR processor with dedicated event-system and interrupt resources. The event system allows peripherals to trigger actions without relying on software polling, which can reduce CPU latency in timing-sensitive designs. Its boot section supports in-system self-programming, while the EEPROM provides nonvolatile parameter storage separate from program Flash. Typical uses include compact industrial controllers, low-power sensor nodes, embedded timing modules, communication peripherals, and consumer-control products. Designers should select external decoupling, clock, and programming support according to the manufacturer data sheet, and verify every board-level signal against the package pinout before layout release. A key design consideration is the limited 8 KB Flash and 1 KB SRAM budget. Firmware and buffers should be sized conservatively, while avoiding blocking delays in event-driven control loops. The device is also available in a TQFP form, so package suffix and land pattern must not be interchanged. This page consolidates verified manufacturer and distributor information, purchase-oriented pricing, and application-specific engineering guidance so engineers can assess the ATXMEGA8E5-MUR before committing a PCB layout.

RFQ İletişim
AVR32DA28-I/SO - 8-bit AVR DA MCU, 32KB Flash, 28-SOIC | Microchip
AVR32DA28-I/SO

AVR32DA28-I/SO - 8-bit AVR DA MCU, 32KB Flash, 28-SOIC | Microchip

The Microchip Technology AVR32DA28-I/SO is an 8-bit AVR® DA family microcontroller with 32 KB of Flash, 4 KB of SRAM, and 512 bytes of EEPROM, running at up to 24 MHz across the full 1.8V to 5.5V supply range, housed in a 28-pin SOIC package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working memory (SRAM), EEPROM, and a rich set of peripherals. The AVR® CPU belongs to a RISC architecture family known for deterministic instruction timing, single-cycle register access, and a mature toolchain (MPLAB X, Atmel Studio, and the Arduino-compatible DxCore core). In the broader taxonomy: AVR® DA -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The 1.8V to 5.5V supply range means the device can run directly from a single Li-ion cell or a regulated 3.3V / 5V rail, simplifying power-tree design. Key features include the hardware multiplier for fast arithmetic, an Event System for inter-peripheral signalling without CPU intervention, intelligent analog peripherals (12-bit ADC, three comparators, three zero-cross detectors, a DAC), capacitive touch (PTC) hardware, six U(S)ARTs, two SPI, and TWI (I²C-compatible). The 28-SOIC (I/SO) variant offers the largest pin count of the SO-package options and provides ample GPIO for keypad, segment-display, and mixed-signal front-ends. Internally, the AVR® DA uses a pipelined Harvard bus: separate Flash and SRAM buses let the CPU fetch instructions and read/write data in the same cycle. The 24 MHz clock, hardware multiplier, and zero-wait-state Flash fetch yield roughly 1 MIPS per MHz, so the part delivers up to ~24 MIPS. The integrated Core Independent Peripherals - Event System, CCL (Configurable Custom Logic), and peripheral touch controller - let complex timing and control tasks run with zero CPU load. Typical applications include capacitive touch human-machine interfaces (HMI), white-goods and small-appliance motor control, LED lighting controllers, sensor hubs with on-chip ADC, and battery-powered IoT nodes. The AVR® DA family is a popular modern replacement for legacy ATmega328P designs that need more Flash, real-time control, and touch capability without migrating to ARM. When designing with the AVR32DA28-I/SO, ensure the ICSP/PDI programming header follows the 6-pin AVR ISP convention with the MCLR pull-up sized for your VDD rail (typically 10 kΩ). Decouple VDD with a 100 nF X7R ceramic placed within 3 mm of each VDD pin, and add a 4.7 µF bulk capacitor near the AVCC pin to keep the ADC reference stable. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

RFQ İletişim
B4420NSE7QQMD - QorIQ Qonverge B4420 SoC, 2x1.6GHz e6500 + 2x1.2GHz SC3900 | NXP Semiconductors
B4420NSE7QQMD

B4420NSE7QQMD - QorIQ Qonverge B4420 SoC, 2x1.6GHz e6500 + 2x1.2GHz SC3900 | NXP Semiconductors

NXP Semiconductors B4420NSE7QQMD is a QorIQ Qonverge B4420 heterogeneous multicore system-on-chip (SoC) for high-performance wireless infrastructure, integrating 2x e6500 PowerPC cores at 1.6 GHz and 2x StarCore SC3900 DSP cores at 1.2 GHz alongside the MAPLE-B3 baseband accelerator. The device is packaged in a 1020-ball FCPBGA (33x33 mm) and is the encrypted, 0-105C temperature-grade variant. The SoC is built on a 64-bit PowerPC e6500 architecture and is targeted at LTE-Advanced (LTE-A) and small-cell base-station designs where heterogeneous compute density matters. A heterogeneous SoC combines CPU, DSP, and hardware accelerator blocks on a single die, allowing baseband processing, L2/L3 protocol stack execution, and acceleration offload to run concurrently without crossing chip boundaries. The B4420 belongs to the QorIQ Qonverge family, itself a sub-family of the QorIQ communications processors, which in turn sits within the broader Power Architecture embedded microprocessor category. This hierarchy - B4420 -> QorIQ Qonverge -> QorIQ -> PowerPC -> communications processor -> microprocessor - reflects how NXP positioned the device for carrier-grade wireless. Key differentiating features include pin- and code-compatibility with the B4860 macrocell SoC, allowing OEMs to reuse a single hardware design and scale software between macrocell and metrocell deployments. The integrated MAPLE-B3 hardware accelerator performs forward-error-correction and turbo decoding at data rates required for 3G/4G modems. Hardware-accelerated security (encrypted variant) protects boot images and runtime code, while 0 to 105C operation suits outdoor base-station enclosures. The B4420 also supports legacy 2G/3G radio access networks, enabling migration paths from existing BTS platforms. Architecture-wise, the SoC combines dual-threaded PowerPC e6500 cores with their out-of-order execution pipeline, dual StarCore SC3900 VLIW DSP cores optimized for vector DSP workloads, and the MAPLE-B3 coprocessor block. A coherent fabric ties all cores to the shared L2/L3 memory subsystem and the high-speed SerDes interfaces. This contrasts with pure-DSP or pure-CPU SoCs that require external glue logic to balance compute loads. Typical applications include LTE small-cell (picocell / microcell / metrocell) base stations, 3G/HSPA+ Node B platforms, multi-standard radio access network (RAN) nodes, and other wireless infrastructure that combines CPU control plane, DSP modem firmware, and forward-error-correction hardware offload. The pin/code compatibility with B4860 also makes B4420 attractive for OEM designs that must scale capacity. A primary design consideration is the high 1020-ball FCPBGA package and 33x33 mm footprint, which demands a multilayer PCB (typically 10+ layers) with controlled-impedance SerDes routing, careful power-rail decoupling, and an experienced assembly flow. Engineers should validate thermal headroom at 105C ambient using the manufacturer's reference design and follow the B4420 Hardware Specifications document for signal-integrity guidelines. This page consolidates distributor stock and authorized-channel pricing, the available same-family and cross-family drop-in alternatives, and practical design considerations not reproduced in the manufacturer datasheet.

RFQ İletişim
BA45F0082 - Fire Protection Flash MCU | Holtek Semiconductor
BA45F0082

BA45F0082 - Fire Protection Flash MCU | Holtek Semiconductor

The Holtek BA45F0082 is a Flash memory type 8-bit high performance RISC architecture microcontroller designed especially for networking fire product peripheral applications, housed in a 16-pin SOP (150-mil, NSOP) package with Flash multi-programming support and an integrated analog front end for alarm sensing. A fire protection Flash MCU is a specialized class of 8-bit microcontroller (MCU) that combines a CPU core, program memory, RAM, peripheral circuits, and analog sensing blocks into a single semiconductor device optimized for smoke detector and fire alarm system nodes. Within the power management and sensing hierarchy of a fire alarm network, these devices sit between the physical smoke/optical sensing elements and the network communication transceiver, executing measurement, filtering, threshold comparison, and alarm signaling tasks. Key features of the BA45F0082 include Flash program memory with multi-programming convenience for field updates and development iteration, a wide range of flexible peripheral functions suited to low-power battery-operated detector nodes, and an application-oriented architecture that reduces external component count in networking fire product peripherals. The device family also includes the BA45FH0082 variant and the BA45V0082 OCDS evaluation chip for in-circuit debugging. Technical architecture is based on Holtek's 8-bit high performance RISC core, which provides fast, compact instruction execution typical of Holtek's BA45 series. Analog-to-digital conversion and digital control functions are integrated on-chip, allowing the detector signal chain to be implemented largely within the MCU. The 111-page manufacturer datasheet (revision V1.10, November 19, 2019) documents the complete register set, electrical characteristics, and package information. Typical applications include networking fire alarm peripheral modules, smoke detector sensor nodes, and fire protection control interfaces where Flash reprogrammability and integrated analog sensing reduce board cost and development time. Distribution data confirms the BA45F0082-16NSOP (SOP-16, 150-mil) package is the standard ordering option. A key design consideration is lifecycle: Holtek has issued formal End Of Life (EOL) notification for the BA45F0082/BA45FH0082, with a latest purchase date of December 25, 2025. New designs should target Holtek's replacement device referenced in the EOL notice, while existing designs should secure last-time-buy inventory or qualify the replacement. This page synthesizes EOL phase-out schedule information, cross-reference guidance, distributor pricing, and family variant data not consolidated in the manufacturer datasheet alone.

RFQ İletişim
BA45F6830 - CO/Gas Detector Flash MCU with Horn Driver | Holtek
BA45F6830

BA45F6830 - CO/Gas Detector Flash MCU with Horn Driver | Holtek

The Holtek Semiconductor BA45F6830 is an 8-bit A/D type Flash microcontroller purpose-built for CO and gas detector applications, integrating a 12V piezoelectric horn driver with on-chip boost converter, an LDO regulator, a buzzer driver, and a high-current LED driver. Its architecture targets the complete signal chain of a residential or industrial gas alarm in a single IC. A CO/gas detector MCU is a specialized class of 8-bit flash microcontroller that combines sensing interfaces, alarm actuation drivers, and power management on one die. In the power-management hierarchy, this device spans voltage regulation (LDO), voltage boosting (boost converter for the piezo horn), and actuator drive (buzzer, LED, horn), reducing the bill of materials for safety-critical alarm products. Key features include the integrated 12V piezoelectric horn driver fed by an on-chip boost converter, which allows alarm sounders to be driven directly from battery or low-voltage rails; a buzzer driver for secondary alert tones; a high-current LED driver for visual status indication; and programmable IOH output current. The Flash program memory supports multiple reprogramming cycles for field updates and manufacturing flexibility. The device is an A/D-type 8-bit high-performance RISC flash MCU. Its analog front-end supports sensor signal acquisition for electrochemical CO cells and catalytic or semiconductor gas sensors, while the RISC core executes alarm-logic, self-test, and calibration routines. Holtek provides an EV chip (BA45V6830) with On-Chip Debug Support (OCDS) so the real MCU device can be debugged during development, and the EV chip and real device are almost functionally identical, easing the transition from emulation to production silicon. Typical applications are standalone CO detectors, combined smoke/CO alarms, combustible gas detectors for kitchens and boilers, and portable gas warning devices where the horn driver, LED driver, and low-power MCU operation must coexist in one battery-powered product. A key design consideration is the boost converter to 12V for the piezo horn: verify horn drive current and boost inductor selection against the datasheet, and budget battery capacity for periodic self-test alarm bursts. This page synthesizes verified distributor and manufacturer data, lifecycle/EOL notices, and practical design guidance not found in a single datasheet, including drop-in replacement guidance as the device approaches its announced phase-out.

RFQ İletişim
BA45F6846 - 8-bit LCD MCU with Piezo Horn Driver | Holtek
BA45F6846

BA45F6846 - 8-bit LCD MCU with Piezo Horn Driver | Holtek

The Holtek BA45F6846 is a Flash Memory A/D type 8-bit high performance RISC architecture microcontroller with a fully integrated LCD driver and an integrated piezoelectric horn driver with boost converter, designed for CO/Gas detector applications requiring an LCD/LED display function. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, sitting at the heart of embedded systems within the broader hierarchy of semiconductor devices (MCU -> embedded processor -> integrated circuit -> semiconductor). The BA45F6846 belongs to Holtek's Battery A/D type 8-bit MCU family, which targets battery-powered sensing products. Key features include Flash program memory for field updates, an integrated multi-channel 12-bit ADC for sensor signal acquisition, a built-in LCD driver capable of driving display segments directly, and a unique piezoelectric horn driver with boost converter that generates the high drive voltage needed for loud alarm sounders directly from a low battery voltage. This integration eliminates external driver and boost circuitry, reducing BOM count and PCB area in alarm products. Architecturally, the device uses Holtek's proven 8-bit RISC core with efficient instruction set, low idle and sleep currents for long battery life, multiple timer modules, and comprehensive low-voltage and watchdog protection functions. The combination of analog front-end, display drive, and audio alarm drive on a single die is what distinguishes this family from generic 8-bit MCUs. Typical applications include carbon monoxide (CO) alarms, combustible gas detectors, smoke/heat alarm combinations, and other battery-powered safety products where an LCD display and a loud piezoelectric sounder are mandatory requirements under safety standards regimes. When designing with the BA45F6846, pay careful attention to sensor front-end grounding and the boost converter layout, as the horn driver switching currents can couple noise into sensitive ADC measurements if ground returns are shared. This page synthesizes datasheet information, application context, and practical design notes not found together on distributor listing pages, with verified sources cited.

RFQ İletişim
BA45FH0082 - 8-bit Fire Protection Flash MCU | Holtek
BA45FH0082

BA45FH0082 - 8-bit Fire Protection Flash MCU | Holtek

The Holtek BA45FH0082 is an 8-bit high-performance RISC Flash microcontroller purpose-built for networking-type fire protection peripheral products, operating from 2.2V to 5.5V with 2KB of embedded Flash program memory, 12-bit resolution A/D capability and a 20-pin SSOP-150mil package. An 8-bit Flash MCU is a complete self-contained computing system that integrates a processor core, program memory, data memory, and peripheral functions such as timers, ADCs and serial communication interfaces on a single chip. Within the embedded systems hierarchy, the BA45FH0082 sits in the application-specific MCU segment, positioned between general-purpose 8-bit MCUs and dedicated ASIC fire-detection ICs, offering the flexibility of Flash reprogramming with detection-optimized peripherals. Key features of the BA45FH0082 include a wide 2.2V~5.5V operating voltage range that supports both battery-powered smoke alarm nodes and 5V industrial panels, 2KB of Flash program memory for application firmware with in-circuit reprogrammability, 128B of RAM for working data, and a 12-bit A/D converter suitable for sensor signal acquisition. According to Holtek documentation, the device architecture is a high-performance RISC core designed specifically for fire protection peripherals with networking capability. Technically, the RISC architecture delivers efficient one-cycle instruction execution for most instructions, while the integrated Flash memory removes the lead-time and inventory constraints of mask ROM devices. The device is RoHS compliant, supporting lead-free assembly processes. Typical applications include networked smoke and heat alarm systems, fire protection peripheral control nodes, sensor polling units in addressable fire alarm loops, and battery-operated detection devices where the wide voltage range extends operating life. Design consideration: because the device is in End-of-Life, designs should evaluate Holtek's officially recommended replacement device referenced in the EOL notification before new layouts are committed. This page synthesizes distributor pricing, EOL lifecycle data, and drop-in alternative analysis not found in the manufacturer datasheet.

RFQ İletişim
BCM2711ZPKFSB06B0TT - Quad Cortex-A72 1.5GHz SoC | Broadcom
BCM2711ZPKFSB06B0TT

BCM2711ZPKFSB06B0TT - Quad Cortex-A72 1.5GHz SoC | Broadcom

The Broadcom BCM2711ZPKFSB06B0TT is a quad-core ARM Cortex-A72 (ARMv8-A, 64-bit) application processor clocked at 1.5 GHz, integrating the VideoCore VI graphics engine with 4Kp60 HEVC decode support, and packaged in a fine-pitch flip-chip BGA (FCBGA) package. It is the system-on-chip at the heart of the Raspberry Pi 4 family. An application processor (AP) is the highest-level device in the embedded computing hierarchy: system-on-chip (SoC) -> application processor -> microprocessor -> computing platform. Unlike a microcontroller, an SoC such as the BCM2711 integrates CPU cores, a graphics pipeline, a memory controller (for LPDDR4 SDRAM), and a full peripheral fabric, and is designed to boot a full operating system such as Linux. Key features include four 64-bit Cortex-A72 cores with out-of-order execution, hardware H.265/HEVC 4Kp60 decode and H.264 1080p60 encode/decode, a PCIe Gen 2 interface, dual MIPI DSI display and dual MIPI CSI-2 camera channels, USB 3.0 and USB 2.0 host support via external controllers, and a Gigabit Ethernet MAC. A rich GPIO bank and legacy BCM2835-compatible peripheral registers ease porting from earlier Raspberry Pi generations. Architecturally, the BCM2711 evolved from the earlier BCM2835/2836/2837 family: the Cortex-A72 cores replace the Cortex-A53 of the BCM2837, delivering roughly 2-3x higher CPU throughput, while the VideoCore VI raises graphics performance substantially over the VideoCore IV. The public BCM2711 ARM Peripherals datasheet (RP-008248, Raspberry Pi Trading Ltd, Version 1, 5 February 2020) documents the peripheral map for OS porting. Typical applications include single-board computers, industrial HMI and edge-AI gateways, digital signage and 4K media players, and embedded vision systems leveraging the dual CSI-2 camera interfaces. Design consideration: the FCBGA package requires controlled-impedance PCB stack-up for LPDDR4, PCIe and USB 3.0 routing, and the SoC needs an external PMIC and boot EEPROM - it is not a stand-alone module. This page adds distributor sourcing data, drop-in alternatives, and design notes not found in the manufacturer datasheet.

RFQ İletişim
BCM2711ZPKFSB06C0T - Quad-Core A72 1.5GHz SoC | Broadcom
BCM2711ZPKFSB06C0T

BCM2711ZPKFSB06C0T - Quad-Core A72 1.5GHz SoC | Broadcom

The Broadcom BCM2711ZPKFSB06C0T is a 64-bit quad-core ARM Cortex-A72 system-on-chip (SoC) running at 1.5 GHz with a VideoCore VI GPU, delivered in a fine-pitch BGA (FBGA) package designed for the Raspberry Pi 4 family of products. This is the exact processor at the heart of the Raspberry Pi 4 Model B and Compute Module 4. A system-on-chip integrates an entire computer - CPU cores, GPU, memory controller, peripheral controllers, and interconnect - onto a single silicon die. SoCs sit at the top of the embedded-computing hierarchy, combining a microprocessor, graphics processor, and microcontroller-class peripherals (GPIO, SPI, I2C, UART, PWM, DMA) into one power-optimized device. The BCM2711 is classified as an application processor / multimedia SoC for embedded and single-board-computer applications. Key features include four 64-bit ARM Cortex-A72 cores with out-of-order execution, hardware H.265 (HEVC) 4Kp60 video decode, dual-display support via two HDMI interfaces at up to 4K resolution, and a substantially upgraded peripheral set over the earlier BCM2837: a PCIe 2.0 lane (used for Gigabit Ethernet via an external LAN controller), native USB 3.0, a redesigned GPIO bank with more flexible alternate functions, and up to 8GB LPDDR4 SDRAM support on the same die via package-on-package memory stacking in end products. Architecturally, the BCM2711 uses an AMBA AXI-compatible interconnect. According to the official BCM2711 ARM Peripherals datasheet, the AXI system does not always return read data in-order; the GPU contains special logic to cope with out-of-order arrivals while the ARM core requires ordered access - a consideration critical for bare-metal OS porting. Peripherals documented in the datasheet include timers, interrupt controller, GPIO, USB, PCM/I2S, DMA controller, and I2C masters. Typical applications are single-board computers (Raspberry Pi 4 Model B), compute modules (CM4), industrial gateways, digital signage and media players leveraging 4Kp60 HEVC decode, and embedded vision or kiosk systems. Design consideration: the BCM2711 requires specific boot media (SPI boot EEPROM plus SD/eMMC) and a regulated core-voltage power tree; thermal design with a heat spreader or heatsink is recommended at sustained CPU load. Verify exact memory-density suffix and package dimensions against the Raspberry Pi technical data sheet before layout. This page synthesizes the manufacturer peripherals documentation, technical data sheet references, drop-in variant analysis, and practical design notes not consolidated in any single manufacturer document.

RFQ İletişim
BCM2835IPPG - ARM11 700MHz SoC BGA | Broadcom
BCM2835IPPG

BCM2835IPPG - ARM11 700MHz SoC BGA | Broadcom

The Broadcom BCM2835IPPG is a multimedia application SoC integrating an ARM1176JZF-S processor core running at 700 MHz with a VideoCore IV GPU, housed in a small BGA package specified over -40C to +105C ambient. It is the processor at the heart of the original Raspberry Pi single-board computer. A system-on-chip (SoC) combines a CPU core, memory controller, graphics engine, and peripheral interfaces onto a single die, forming the top of the embedded processing hierarchy (SoC -> application processor -> microprocessor -> semiconductor IC). SoCs reduce board area, BOM count, and system power compared with discrete CPU-plus-chipset designs, which is why they dominate cost-sensitive multimedia and embedded Linux platforms. Key features of the BCM2835 include the ARM1176JZF-S core with a floating-point unit and 128 KB or larger L2 cache, the VideoCore IV GPU capable of hardware decode of 1080p30 H.264 video, a hardware ISP for image processing, and an integrated USB 2.0 OTG controller. The device provides 54 GPIO lines and peripheral functions including timers, an interrupt controller, PCM/I2S audio, UART, SPI, and I2C, as documented in the manufacturer datasheet covering Timers, Interrupt controller, GPIO, USB, PCM/I2S (205 pages). Architecturally, the BCM2835 couples the ARM11 CPU to the VideoCore IV graphics and multimedia pipeline through shared SDRAM. The GPU handles boot initialization, graphics acceleration (OpenGL ES 2.0 and OpenVG), and fixed-function video codecs, allowing the CPU to focus on application workloads. The board-level SDRAM interface and peripheral muxing are defined in the BCA ballout documented in the datasheet. Typical applications include single-board computers, embedded Linux HMIs, digital signage players, IP camera and video capture systems, industrial control panels, and educational computing platforms. The hardware H.264 engine and ISP make the part especially well suited to video-centric designs that must remain within a low bill-of-materials budget. Designers should treat the BCM2835IPPG as a board-level design: SDRAM, power rails, clocking, and boot flash must be implemented per the reference schematics in the manufacturer datasheet, and BGA assembly requires controlled-impedance, fine-pitch PCB processes. This page synthesizes distributor stock listings, the 205-page manufacturer datasheet reference, and sourcing notes for the BCM2835IPPG in one place, information not consolidated on any single distributor page.

RFQ İletişim
BCM2835RIPPG - ARM11 700MHz SoC | Broadcom | Embedded
BCM2835RIPPG

BCM2835RIPPG - ARM11 700MHz SoC | Broadcom | Embedded

The Broadcom BCM2835RIPPG is the BCM2835 system-on-chip (SoC) supplied in the proprietary BGA package identified by the IPPG ordering code. The BCM2835 integrates an ARM1176JZF-S application processor core with a VideoCore IV graphics and multimedia engine, together with timers, an interrupt controller, GPIO, USB, and PCM/I2S peripherals, as described in the manufacturer datasheet. A system-on-chip is a single integrated circuit that consolidates the CPU, GPU, memory controller, and peripheral functions that traditionally occupied multiple chips. SoCs sit at the top of the embedded processing hierarchy (SoC -> microprocessor unit -> integrated circuit -> semiconductor), and the BCM2835 is the device class popularized by the original Raspberry Pi single-board computer, where it handled general-purpose Linux execution plus 1080p-class video decode through VideoCore IV. Key features of the BCM2835 family include the ARM1176JZF-S core, which provides an ARMv6 instruction set, an FPU, and JTAG debug; the VideoCore IV multimedia processor for graphics and video; and a rich peripheral set covering GPIO banks, I2C, SPI, UART, USB 2.0 host/device, and PCM/I2S audio. The IPPG suffix on this MPN identifies Broadcom's packaged ordering option; the specific package dimensions and pin count for this ordering code are not published in the verified data and are marked accordingly in the specifications table. Architecturally, the BCM2835 couples the general-purpose ARM core to a shared memory system and a dedicated multimedia subsystem, allowing Linux workloads and real-time video/audio pipelines to proceed concurrently. Peripheral functions are memory-mapped, and the datasheet documents register-level access for timers, the interrupt controller, GPIO, USB, and PCM/I2S blocks. Typical applications include single-board computers, embedded multimedia players, industrial HMI and kiosk controllers, and educational/prototyping platforms where GPIO plus Linux-class processing are required in one device. A key design consideration is that the ARM1176 is an ARMv6-class core; software stacks must be built for ARMv6 rather than ARMv7/ARMv8, and sourcing for this legacy SoC should be validated early in a project lifecycle. This page synthesizes distributor availability from Octopart and multiple brokers, datasheet provenance, and drop-in-alternative analysis not found on a single manufacturer page.

RFQ İletişim
BCM2836IFBG - Quad-Core ARM SoC, BGA | Broadcom
BCM2836IFBG

BCM2836IFBG - Quad-Core ARM SoC, BGA | Broadcom

The Broadcom BCM2836IFBG is a quad-core ARM Cortex-A7 system-on-chip (SoC) running at 900 MHz with the VideoCore IV multimedia GPU, supplied in a BGA package. It is the processor used in the Raspberry Pi 2 Model B and integrates the CPU, GPU, SDRAM interface, peripherals, and boot ROM on a single die. A system-on-chip (SoC) is a highly integrated semiconductor that combines the functions of a computer system - processor cores, memory controller, graphics engine, and I/O interfaces - into a single package. Within the product hierarchy, the BCM2836 is an application processor belonging to the Broadcom BCM28xx multimedia SoC family, positioned above general-purpose microcontrollers and below application processors with integrated large DRAM. The BCM2836 succeeded the single-core BCM2835 by replacing the ARM11 core with a quad-core Cortex-A7 cluster, delivering roughly a sixfold increase in CPU throughput while retaining the same VideoCore IV GPU and peripheral set. Key features include four ARM Cortex-A7 cores with NEON SIMD and VFPv4 floating point, a 32 KB L1 instruction/data cache per core, a 512 KB shared L2 cache, the VideoCore IV GPU with 1080p30 H.264 decode capability, and peripheral blocks such as GPIO, UART, SPI, I2C, USB 2.0 (via a hub/LAN9514 companion on Raspberry Pi boards), timers, interrupt controller, and PCM/I2S audio interfaces. Per the public Broadcom BCM2835/BCM2836 peripheral documentation, memory ordering, GPIO, and interrupt architecture are shared across the family, easing software migration from BCM2835 designs. The BCM2836 architecture pairs the Cortex-A7 MPCore cluster with the VideoCore IV graphics pipeline and a shared memory system clocked by an LPDDR2 SDRAM controller. The partitioning allows Linux (Raspbian/Raspberry Pi OS, 32-bit ARMv7) to run on the ARM cores while the GPU handles graphics, camera ISP, and secure boot duties, with firmware-loaded kernel images delivered from the SD card boot flow used in Raspberry Pi products. Typical applications include single-board computers, embedded HMI and digital signage controllers, industrial gateways, and multimedia set-top platforms - use cases that need 1080p video, USB connectivity, and a mature Linux ecosystem on a cost-effective SoC. A key design consideration is thermal and power management: the four Cortex-A7 cores at 900 MHz typically require a 5 V, 2 A-class supply in reference designs, and under sustained multi-core load a heat spreader or airflow is recommended in enclosed enclosures. This page synthesizes distributor sourcing data, drop-in family alternatives, and practical design notes not found in the manufacturer documentation.

RFQ İletişim
BCM2836RIFBG - Quad-Core Cortex-A7 SoC 900MHz | Broadcom
BCM2836RIFBG

BCM2836RIFBG - Quad-Core Cortex-A7 SoC 900MHz | Broadcom

The Broadcom BCM2836RIFBG is a quad-core ARM Cortex-A7 system-on-chip (SoC) running at 900 MHz with an integrated VideoCore IV GPU, housed in a ball grid array (BGA) package. This SoC is the application processor used on the Raspberry Pi 2 Model B and combines CPU, GPU, memory controller, and multimedia peripherals on a single die. A system-on-chip is an integrated circuit that integrates all major functional blocks of a computing system onto one die: processor cores, graphics acceleration, memory interface, peripheral controllers, and interconnect fabric. SoCs sit at the top of the embedded processor hierarchy (SoC -> application processor -> microprocessor -> semiconductor) and eliminate the need for discrete CPU, GPU, and controller chips in compact designs. Key features of the BCM2836 include four ARM Cortex-A7 cores with NEON SIMD and VFPv4 floating-point units, 32 KiB L1 instruction and data caches per core, and a shared 512 KiB L2 cache. The VideoCore IV graphics core supports 1080p30 H.264 decode and OpenGL ES 2.0-class 3D graphics. Peripheral set includes USB 2.0 host/OTG, 10/100 Ethernet MAC support via companion PHY, UART, SPI, I2C, PWM, and general-purpose I/O banks. The architecture pairs the Cortex-A7 cluster with the proprietary VideoCore IV multimedia engine, connected by an internal bus fabric. Boot code resides in on-chip ROM, with secondary bootloader loaded from external storage such as an SD card. Typical applications include single-board computers, embedded Linux gateways, industrial HMIs, digital signage players, and multimedia IoT nodes requiring 1080p video output. Design consideration: the BCM2836 is supplied under restricted documentation; full electrical and ballout details are available from Broadcom under NDA, so board design should reference the Raspberry Pi 2 reference schematics. This page synthesizes distributor availability, family alternatives, and practical design guidance not found in publicly restricted datasheets.

RFQ İletişim
BCM2837B0IFSBG - Quad-Core Cortex-A53 SoC BGA | Broadcom
BCM2837B0IFSBG

BCM2837B0IFSBG - Quad-Core Cortex-A53 SoC BGA | Broadcom

The Broadcom BCM2837B0IFSBG is a quad-core ARM Cortex-A53 application processor (SoC) supplied in a BGA package. According to the BCM2837 datasheet from Broadcom, the BCM2837 is an A53 processor built around four 64-bit ARM Cortex-A53 CPU cores integrated with a multimedia GPU and system peripherals on a single die. An application processor SoC is the highest level of integration in the semiconductor hierarchy: within a power-management and computing hierarchy it combines a central processing unit (CPU), graphics processing unit (GPU), memory interfaces, and I/O peripherals into one chip, replacing the multi-chip solutions of earlier embedded boards. SoCs of this class sit above microcontrollers in capability and are the computational heart of single-board computers, embedded media systems, and industrial gateways. Key features of the BCM2837 family include its quad-core Cortex-A53 architecture supporting 64-bit ARMv8-A execution, an integrated multimedia GPU for video and graphics acceleration, and a peripheral set documented in the Broadcom 'BCM2835 ARM Peripherals' manual that also covers the BCM2837 die. The BGA package provides a dense, low-inductance surface-mount interconnect suited to high-speed memory and interface routing. Architecturally, the BCM2837B0 pairs the A53 cluster with Broadcom's VideoCore-class multimedia engine, allowing Linux-based operating systems to run while hardware blocks handle video decode, 3D graphics, and camera input. This split between general-purpose cores and fixed-function accelerators is what made the BCM2837 family the processor of choice for the Raspberry Pi 3 generation of boards. Typical applications include single-board computers, embedded HMI and display systems, industrial IoT gateways, digital signage media players, and networked camera or kiosk designs where a Linux-capable processor with graphics output is required in a compact footprint. A key design consideration with this BGA device is that it is a raw SoC requiring external boot media (SD/eMMC), power rails, and memory configuration; board bring-up must follow the reference schematic in the Broadcom documentation, and reflow assembly requires BGA-capable processes and X-ray inspection. This page synthesizes distributor sourcing data, same-family drop-in cross references, and practical design notes not found in the manufacturer datasheet, providing procurement and engineering context in one place.

RFQ İletişim
BCM2837RIFBG - Quad Cortex-A53 1.2GHz SoC | Broadcom
BCM2837RIFBG

BCM2837RIFBG - Quad Cortex-A53 1.2GHz SoC | Broadcom

The Broadcom BCM2837RIFBG is a quad-core ARM Cortex-A53 system-on-chip running at 1.2 GHz and delivering approximately 2760 DMIPS per core, housed in a ball grid array (BGA330) package. It is the processor used in the Raspberry Pi 3 family of single-board computers. A system-on-chip (SoC) integrates all major functional blocks of a computing system onto a single silicon die, combining CPU cores, graphics processing, memory interfaces, and peripheral controllers. In the embedded hierarchy, the BCM2837 sits above microcontrollers and below multi-core application processors for mobile devices, targeting cost-sensitive Linux-capable embedded platforms. Key features include four 64-bit ARM Cortex-A53 cores clocked at 1.2 GHz, a Broadcom VideoCore IV GPU capable of hardware-accelerated graphics and 1080p video decode, and a rich peripheral set including USB 2.0, CSI camera and DSI display interfaces, and general-purpose I/O. The 64-bit ARMv8-A architecture allows execution of both 32-bit and 64-bit operating systems, with mainstream Linux support via the Raspberry Pi OS. Architecturally, the BCM2837 couples the quad-core Cortex-A53 cluster to the proven BCM283x peripheral complex originally developed for the BCM2835. This preserves software compatibility with earlier Raspberry Pi generations while multiplying compute throughput roughly tenfold. The VideoCore IV GPU also services camera and display pipelines, offloading video workloads from the CPU cores. Typical applications include single-board computers, industrial IoT gateways, digital signage players, kiosk controllers, HMI panels, and educational computing platforms. Its Linux ecosystem, broad community support, and integrated GPU make it well suited to products that need a full OS with multimedia capability. Design consideration: as a BGA-packaged SoC, the BCM2837RIFBG requires controlled-impedance PCB stackups for LPDDR2 memory routing, precise power sequencing, and careful thermal management, since the processor load can raise die temperature substantially in enclosed enclosures. Refer to the Raspberry Pi Foundation reference designs for proven power-tree implementations. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing references as of 2026-09-14.

RFQ İletişim