Mikrodenetleyiciler

Ürünler (20.000+)

MC68EC000FU16 - 16MHz M68000 16-bit MPU, 64-QFP | Motorola
MC68EC000FU16

MC68EC000FU16 - 16MHz M68000 16-bit MPU, 64-QFP | Motorola

The Motorola MC68EC000FU16 is a 16-bit microprocessor from the M68000 (m68k) family operating at 16 MHz, housed in a 64-pin QFP (14x14 mm) package. It is the cost-reduced EC (Embedded Controller) variant of the original MC68000, featuring an 8-bit external data bus instead of the full 16-bit bus, while preserving the 32-bit internal register file and 24-bit address bus for up to 16 MB of linear addressing. What is an M68000 microprocessor? The M68000 (often called "68k") is a CISC microprocessor architecture introduced by Motorola in 1979 that pioneered 32-bit internal programming with 16-bit external data and 24-bit address buses for early Unix workstations, arcade systems, gaming consoles, and industrial controllers. Within the M68000 taxonomy (MC68000 -> MC68EC000 -> MC68SEC000), the MC68EC000 retains full instruction-set compatibility with the original 68000 but simplifies the bus interface to 8-bit data, reducing pin count and enabling smaller, lower-cost embedded designs where the original 16-bit bus was unnecessary. Key features of the MC68EC000FU16 include 8 32-bit data registers, 8 32-bit address registers, 16 MB linear address space, 56 instruction types with 5 main addressing modes, supervisor/user operating modes, and 7 levels of interrupt priority. It supports vectored interrupts, a TRAP instruction, and the full M68000 exception processing model used by countless 68k operating systems and bare-metal firmware. Static HCMOS technology allows clock speeds down to DC for low-power standby designs. Architecturally, the MC68EC000FU16 implements a microcoded CISC engine with a 4-byte instruction prefetch queue, two supervisor stack pointers, and on-chip memory management through function codes only (no MMU). It is fully software-compatible with the original MC68000 and MC68SEC000, allowing code written for one variant to run on the others when bus-width differences are handled. Typical applications include industrial controllers, embedded instrumentation, point-of-sale terminals, legacy system maintenance, automotive ECU prototypes, and education platforms for 68k assembly learning. The 64-pin QFP package is significantly smaller than the original 64-pin DIP, allowing space-constrained retrofits. Designers should note that the MC68EC000FU16 requires an external clock oscillator and a bus arbitration scheme. Because the bus is 8-bit, 32-bit memory accesses take 4 cycles versus 2 cycles on a full MC68000. Choose the FU16 speed grade for systems targeting 16 MHz operation. This page synthesizes distributor stock, drop-in alternatives, and practical design notes not found in the original Motorola M68000 addendum.

RFQ İletişim
MC68EC020AA16 - 16MHz 32-Bit M68000 MPU | NXP | 100-QFP
MC68EC020AA16

MC68EC020AA16 - 16MHz 32-Bit M68000 MPU | NXP | 100-QFP

The NXP (formerly Motorola/Freescale) MC68EC020AA16 is a 16MHz, 32-bit HCMOS microprocessor from the M68000 family, packaged in a 100-pin QFP (14x20 mm). It is the EC (Embedded Controller) variant of the full MC68020, retaining a 32-bit internal architecture while removing the coprocessor interface and instruction cache to reduce cost and silicon complexity for embedded applications. The MC68EC020 belongs to the M680x0 microprocessor family, a 32-bit CISC architecture that evolved from the original Motorola 68000 introduced in 1979. The M68000 family occupies a distinct position in microprocessor history: it powered iconic systems including the Apple Macintosh, Amiga, Atari ST, Sega Genesis, and early Sun workstations. EC versions embedded the market an economical 32-bit engine, retaining full 32-bit registers, data paths and addressing while omitting the MMU and floating-point coprocessor interface, making them well-suited to deterministic single-purpose controllers. Key features of the MC68EC020AA16 include a 16.67MHz clock, 10 MIPS sustained throughput, 32-bit data and address buses, 8 32-bit general-purpose data registers, and a 16-bit asynchronous bus interface. The static HCMOS design allows the clock to be stopped without losing internal state, enabling low-power standby modes. The device operates from a single 5V supply and supports seven asynchronous bus arbitration levels. At the architecture level, the MC68EC020AA16 implements a 32-bit programming model, an instruction cache-less pipeline (vs the full MC68020), a barrel shifter for single-cycle multi-bit shifts, and a multiply/divide unit supporting 32x32-bit signed/unsigned operations in tens of cycles. The integrated MMU-less memory model simplifies board design and software: embedded firmware can use a flat 4GB address space without translation tables. Typical applications include industrial motion controllers, laser printer engines, RAID storage controllers, telecommunications switches, point-of-sale terminals, and avionics subsystems. The combination of deterministic execution, static HCMOS design, and the large M68000 software ecosystem (including compilers and RTOS ports) keeps the part in production for long-lifecycle embedded systems. When designing with the MC68EC020AA16, ensure the 5V power rail is well decoupled and that bus termination matches the asynchronous memory timing budget. The static core allows clock-stopped operation, simplifying board design. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated in the legacy Motorola Freescale datasheet.

RFQ İletişim
MC68EC020AA25 - 32-Bit 25MHz M680x0 MPU | NXP | 100-QFP
MC68EC020AA25

MC68EC020AA25 - 32-Bit 25MHz M680x0 MPU | NXP | 100-QFP

The NXP MC68EC020AA25 is a 32-bit M680x0 microprocessor (MPU) operating at 25 MHz, housed in a 100-pin QFP (Quad Flat Package, 14x20 mm) and originally designed and manufactured by Motorola as a member of the 68020 family. It belongs to the "EC" (Embedded Controller) sub-family: a cost-reduced variant of the full MC68020 that omits the built-in MMU while retaining the full 32-bit data paths, 32-bit registers, 32-bit address bus, and the same instruction set as the parent MC68020. According to the Freescale/Motorola 68EC020 datasheet, this part is intended for embedded designs that need 68020 CPU horsepower but do not require hardware virtual-memory support. The 100-QFP package is a Plastic Quad Flat Pack with 100 gull-wing leads on a 14x20 mm footprint. A microprocessor (MPU) is the central processing unit of an embedded computer system implemented as a single integrated circuit. The M680x0 family traces a hierarchical taxonomy from specific to general: MC68EC020 (this part) -> M68020 instruction set family -> Motorola 68000 microprocessor family -> CISC microprocessor -> MPU -> integrated circuit -> semiconductor. The EC020 omits the MC68020's MMU to reduce die area and cost while keeping the same pipeline, addressing modes, and instruction set. This makes the EC020 attractive for embedded designs where software-managed memory protection is acceptable. Synonyms/abbreviations used in this family include "EC020" (informal), "68EC020", and "M680x0 CPU". Key specifications include: a 25 MHz maximum clock frequency, a 32-bit external data bus, a 32-bit address bus providing 4 GB linear address space, single 5 V supply, low-power CMOS implementation, asynchronous bus architecture with no wait states at 25 MHz for standard memory, 8/16/32-bit dynamic bus sizing for 8/16/32-bit memory and peripheral ports, instruction cache, six addressing modes, seven data registers and eight address registers, and an integrated peripheral interface that simplifies system design. Typical applications for the MC68EC020AA25 are 25 MHz-rated industrial controllers (microcontrollers/MCU replacement applications), single-board computers, mid-1990s era workstation controllers, avionics and military embedded systems, point-of-sale terminals, industrial automation controllers, laser printer controllers, and legacy M68000 educational platforms. Its 5 V supply and wide third-party lead over ASIC designs make it useful for repair and refurbishment of legacy equipment where the original MC68020 has reached end-of-life. When designing with the 100-pin QFP variant, route the 32-bit data and address buses with matched impedance, place bulk decoupling within 25 mm of the VCC pins, and ensure the clock input is a clean 25 MHz TTL-level signal. Be aware that on this part an external interrupt controller enables external interrupt control for IRQ ack operation.

RFQ İletişim
MC68EC040FE20A - 32-Bit 68040 MPU 20MHz 184-CQFP | Motorola
MC68EC040FE20A

MC68EC040FE20A - 32-Bit 68040 MPU 20MHz 184-CQFP | Motorola

The Motorola MC68EC040FE20A is a 32-bit RISC microprocessor from the M68000 family, operating at 20 MHz in a 184-pin Ceramic Quad Flat Pack (CQFP, 31.3 x 31.3 mm) package. It is a cost-reduced, EC (Embedded Controller) variant of the full MC68040, omitting the integrated MMU and FPU while retaining the on-chip instruction and data caches, pipelined integer core, and burst-mode bus interface. A 68040 microprocessor is a fourth-generation member of the Motorola M68000 (68k) instruction-set architecture family. The 68k family is a CISC architecture that, despite its name, shares many RISC design principles (orthogonal register set, simple addressing modes) and dominates embedded applications such as networking gear, industrial controllers, and aerospace systems. The 'EC' suffix designates embedded-controller derivatives with peripherals or features removed to lower cost and power; the 'FE' package code denotes the ceramic CQFP, while the '20A' speed code indicates a 20 MHz clock grade with the 'A' silicon revision. Key features include a 32-bit data bus and 32-bit address bus supporting 4 GB linear addressing, on-chip 4 KB instruction cache and 4 KB data cache (write-through), a burst-fill bus interface for fast cache line loads, and a 5.0 V I/O voltage supply. The device uses HCMOS technology for low power consumption relative to earlier NMOS 68k parts. The 184-pin CQFP package is qualified for harsh-environment applications including military and aerospace systems, with a wide operating-temperature range typical of ceramic-packaged Motorola processors. The MC68EC040 integrates a six-stage integer pipeline, supports multiprocessor configurations through dual-function bus arbitration pins, and provides dedicated control signals for snooping in symmetric multiprocessing. It executes the full M68000 instruction set including bit-field operations, privilege levels, and exception handling, ensuring software compatibility across the entire 68k product line including the MC68020, MC68030, and full MC68040. Cache control is via the CACR (Cache Control Register) and the MOVE-to-SR instructions used by operating systems to maintain coherency. Typical applications cover embedded aerospace and defense systems, VMEbus single-board computers, legacy networking routers running 68k-based firmware, industrial control PLCs, and retro-computing and emulation platforms. The ceramic CQFP package and the mature 68k toolchain make this part particularly attractive for long-lifecycle programs requiring 10-20+ years of component availability and proven reliability. When designing with this device, ensure proper bus-termination and clock-signal integrity because the 20 MHz synchronous bus generates harmonics that require impedance-controlled traces. The 5 V supply must be decoupled with 0.1 uF and 10 uF capacitors placed within 25 mm of each VDD/VSS pair. This page synthesizes distributor pricing, 184-CQFP footprint cross-references, and practical design notes not found in the original Motorola datasheet, providing engineers with a single source for sourcing, replacement, and design-in guidance.

RFQ İletişim
MC68EC040RC20A - 32-bit M68000 MPU 20MHz 179-PGA | NXP
MC68EC040RC20A

MC68EC040RC20A - 32-bit M68000 MPU 20MHz 179-PGA | NXP

The NXP (formerly Motorola/Freescale) MC68EC040RC20A is a 32-bit M68000-family microprocessor running at 20 MHz, packaged in a 179-pin PGA (Pin Grid Array, 47.24 x 47.24 mm) ceramic/ceramic-equivalent socket form factor. It is the cost-reduced 'EC' variant of the 68040 line, with the integrated floating-point unit (FPU) and memory management unit (MMU) removed to lower silicon cost while retaining the 68040 instruction set, on-chip 4 KB instruction cache and 4 KB data cache, six-stage pipeline, and 32-bit address/data bus. A microprocessor (MPU) is the central execution unit of an embedded computer system: it fetches instructions from memory, decodes them, and drives peripherals via address, data, and control buses. The 68k family sits in the same hierarchy as ARM and x86 embedded parts, and the EC040 in particular is a 'cache-only' reduced variant used in legacy VMEbus boards, industrial controllers, and aerospace retrofits where deterministic integer performance and software compatibility outweigh the need for an FPU or hardware memory management. Key features include 20 MIPS integer throughput at 20 MHz, dual 4 KB on-chip caches, a 32-bit internal data path, Burst mode bus support for filling cache lines, and full M68040 instruction-set compatibility (excluding MMU/FPU opcodes). The 179-pin PGA package supports through-hole socket mounting on a 2.54 mm grid, with 32 address lines, 32 data lines, and dedicated transfer-acknowledge/arbitration pins. The 'EC' variant removes the MMU and FPU, allowing software to use a flat physical-address model. It is electrically and pin-compatible with the full MC68040 (when the FPU/MMU are not required), making it a common cost-down substitute in mature designs. Operating voltage is 5.0 V, junction temperature range 0C to +70C (commercial grade, 'RC' suffix). Typical applications include legacy VMEbus single-board computers, industrial automation controllers, aerospace/avionics retrofits, telecom switching line-cards, and embedded instrumentation where existing 68k binary code must be preserved. When designing with this part, ensure your memory subsystem can supply data at the burst rate, since a cache miss can stall the pipeline. Decoupling and clock-signal integrity are critical at 20 MHz; place bulk and ceramic decoupling capacitors close to the PGA socket pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
MC68EC040RC25A - 32-Bit 25MHz M68040 MPU | NXP 179-PGA
MC68EC040RC25A

MC68EC040RC25A - 32-Bit 25MHz M68040 MPU | NXP 179-PGA

The NXP MC68EC040RC25A is a 32-bit reduced-instruction-set microprocessor (MPU) from the M680x0 family, operating at 25 MHz and housed in a 179-pin PGA (Pin Grid Array) package. It is the "EC" (Embedded Controller) variant of the Motorola 68040, integrating a 4 KB instruction cache and 4 KB data cache on-die while omitting the integrated floating-point unit (FPU) to reduce cost and power. The 'A' suffix denotes a die revision/upgrade that improves manufacturing yield and AC electrical characteristics relative to earlier revisions. An MPU (Microprocessor Unit) is the central execution engine of a computing system, fetching instructions from memory, decoding them, and driving external memory and peripheral devices through its address and data buses. The MC68EC040RC25A belongs to the CISC (Complex Instruction Set Computer) M68000 microprocessor family and inherits the 32-bit linear address space, orthogonal register set, and memory management primitives of that lineage. Within the broader taxonomy, it sits at: MPU -> 32-bit MPU -> M68k family -> M68040 generation -> embedded controller variant. Key features include a 25 MHz maximum clock input, a 32-bit external data bus, a 32-bit address bus (4 GB linear space), on-chip 4 KB + 4 KB separate instruction and data caches, a bus interface unit with burst-mode support, and compatibility with the 68000/68010/68020/68030 instruction set (excluding FPU instructions). The device is fabricated in HCMOS technology and specified for a single 5 V supply, with TTL-compatible I/O. Architecturally the MC68EC040RC25A uses a Harvard-style split cache with a write-back policy, dual instruction prefetch pipelines, and an integrated memory management unit that supports demand-paged virtual memory with 4-KB pages. The 'EC' variant deliberately excludes the FPU; system designers needing IEEE-754 floating-point must add an external MC68881/MC68882 coprocessor via the coprocessor interface. Typical applications include embedded industrial controllers, laser printer engines, network routers, telecom control planes, mid-1990s workstation-class compute nodes, and legacy military/aerospace systems that standardized on the 68040 platform. The wide third-party software base (Linux/m68k, NetBSD/m68k, VxWorks) and rugged PGA package make it a long-life part for these designs. When designing with the MC68EC040RC25A, pay particular attention to the coprocessor interface if your software issues FPU opcodes. The 179-pin ceramic PGA package requires a matching socket (e.g., PGA179) and a properly designed 4-layer or 6-layer PCB to maintain signal integrity on the 32-bit memory bus at 25 MHz. This page synthesizes distributor pricing, drop-in alternative candidates, and design considerations drawn from manufacturer documentation that are not aggregated on a single distributor product page.

RFQ İletişim
MC68EC040RC33A-FR - 33MHz 68040 MPU 179-PGA | Freescale
MC68EC040RC33A-FR

MC68EC040RC33A-FR - 33MHz 68040 MPU 179-PGA | Freescale

The Freescale (formerly Motorola, now NXP-legacy) MC68EC040RC33A-FR is a 33 MHz 32-bit CISC microprocessor from the M680x0 family, implemented in HCMOS technology and housed in a 179-pin Pin Grid Array (PGA) package measuring 47.24 mm x 47.24 mm. As the 'EC' (Embedded Controller) variant of the 68040, it integrates an 8 KB on-chip instruction/data cache, a memory management unit bypassed for embedded use, and a 32-bit data bus, targeting cost-sensitive embedded and industrial designs that need the 68040 instruction set without the full MMU. A microprocessor (MPU) is the central processing unit of a computer system, executing instructions fetched from memory and controlling peripheral devices through buses. The MC68040 family belongs to the M68000 architecture hierarchy: 32-bit CISC microprocessor -> M680x0 family -> Motorola/NXP legacy portfolio -> embedded MPU. Its HCMOS fabrication process yields a typical 5 V single-rail supply, fast static design, and the classic 68000 programmer's model with eight 32-bit data registers and eight 32-bit address registers. Key features include 33 MHz core clock, integrated 8 KB unified instruction/data cache (Harvard-style split internally), a 32-bit external data bus with dynamic bus sizing to 8/16 bits, and a built-in burst-mode memory controller. The 'EC' designation removes the full MMU found on the MC68040, replacing it with simple access protection suitable for real-time embedded operating systems. The 179-pin ceramic PGA provides robust thermal performance for industrial environments and supports socketed prototyping or production assembly. The architecture combines a six-stage instruction pipeline with dual instruction-fetch and execution units, allowing the 68040 to approach RISC-like throughput on optimized code while preserving full 68000 binary compatibility. Floating-point hardware is retained on the 'RC' (ceramic PGA) package variant, making this part well suited to legacy VMEbus designs, industrial controllers, aerospace retrofits, and military systems where long-term availability and second-source supply are mandatory. Typical applications include VMEbus single-board computers, industrial automation controllers, legacy aerospace and defense electronics, telecommunications switches based on 68040, and retro-computing platforms replicating classic Sun 3 / NeXTstation workstations. The wide operating voltage and proven HCMOS reliability also make it common in medical imaging equipment and railway signaling controllers. Designers pair the MPU with companion chips such as the MC68882 floating-point coprocessor (not required here, FPU is on-die), MC68681 DUART, and MC68901 MFP for complete system integration. When designing with this part, ensure the 179-pin PGA socket is keyed correctly and that the 5 V supply decoupling network is sized for the peak dynamic current of a 33 MHz core. Designers transitioning to a RoHS-compliant board should consult NXP's migration guide, because the original 179-PGA package is supplied with lead-containing ceramic that affects RoHS compliance status. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The MC68EC040RC33A-FR is widely available through authorized distributors and legacy-stock specialists such as Rochester Electronics, with pricing typically ranging from $70 to $185 per unit depending on quantity, screening level, and date code.

RFQ İletişim
MC68EC040RC40A - 32-Bit 40MHz M680x0 MPU | NXP | 179-PGA
MC68EC040RC40A

MC68EC040RC40A - 32-Bit 40MHz M680x0 MPU | NXP | 179-PGA

The NXP MC68EC040RC40A is a 32-bit M680x0 microprocessor IC with integrated cache, operating at a 40 MHz clock speed, housed in a 179-pin PGA (Pin Grid Array) ceramic package measuring 47.24 x 47.24 mm. It is the cost/feature-reduced member of the M68040 family (the "EC" variant lacks the integrated floating-point unit of the full MC68040, but retains the 8 KB instruction and 8 KB data on-chip caches), targeting embedded control applications where MMU-based virtual memory is unnecessary. The MC68EC040 belongs to the Motorola/Freescale/NXP M68000 microprocessor family - a CISC 32-bit architecture that traces lineage back to the original MC68000 of 1979. Within the broader taxonomy, the M680x0 sits as a high-performance general-purpose MPU (distinct from the smaller ColdFire family that derives from it). Each successive generation added caches, MMUs, and FPU integration; the EC040 specifically adds caches but omits the MMU found in the full MC68040, giving embedded designers a deterministic, real-time-friendly memory model. Key features include a 40 MHz maximum operating frequency, 5 V power supply, 32-bit data/address bus, separate 8 KB instruction and 8 KB data write-back caches, hardware multiply/divide, and a six-stage instruction pipeline. The part supports burst-mode memory accesses and a burst-fill bus protocol that maximises throughput to external SRAM. The 179-PGA ceramic package is designed for through-hole PCB mounting and socket insertion, which was standard for MPU evaluation platforms and industrial control boards of its era. Typical applications include industrial process controllers, CNC machine tool controllers, medical instrumentation controllers, data acquisition systems, and legacy upgrade designs where the developer needs a 32-bit MPU with deterministic execution, on-chip cache, and pin compatibility with the full M68040 family footprint. Embedded Linux or RTEMS deployments that have already been ported to the EC040 can also benefit from a single-source upgrade to higher-speed variants. When designing with this device, ensure proper power-supply decoupling (multiple bulk and 0.1 uF ceramic caps) on the 5 V rails, careful signal integrity planning for the 40 MHz system clock domain, and adequate thermal dissipation through the PGA heatsink interface. Bus arbitration and cache coherency must be managed explicitly in multi-master systems.

RFQ İletişim
MC68EC060RC50 - 50MHz 32-Bit 68060 MPU PGA | NXP
MC68EC060RC50

MC68EC060RC50 - 50MHz 32-Bit 68060 MPU PGA | NXP

The NXP MC68EC060RC50 is a 32-bit microprocessor from the M680x0 (MC68060) family, integrating an 8KB instruction cache, 8KB data cache, and a 6-entry instruction buffer into a single die. It runs at 50 MHz and is housed in a 206-pin ceramic Pin Grid Array (PGA/BEPGA, 47.25 x 47.25 mm). Core supply voltage is specified at 3.3 V with 5 V tolerant I/O per the M68060 User's Manual. The 68060 superscalar core executes up to two instructions per clock (integer + branch) and integrates a dual-issue FPU for 32-bit single-precision and 64-bit double-precision IEEE-754 floating point. What is a 32-bit embedded microprocessor? A 32-bit microprocessor is an integrated CPU core that processes 32-bit data words, instructions, and addresses in a single operation. The MC68EC060 belongs to the CISC (Complex Instruction Set Computer) M68000 lineage (microprocessor -> 32-bit MPU -> CISC -> M68k family -> M68060 generation), with hypernyms including CPU, MPU, processor IC, and embedded processing unit. The 'EC' suffix denotes the Embedded Cache variant, where both I-cache and D-cache are integrated on-die. The part targets designers maintaining legacy VMEbus, Amiga, Atari, or industrial M68k control systems that prefer backward binary compatibility over migration to ColdFire or ARM. Key features of the MC68EC060RC50 include its MMU with 4-entry fully associative instruction and data translation lookaside buffers (ITLB/DTLB) supporting 4KB to 8MB pages, a branch cache combining buffer (CB), and a barrel shifter for single-cycle shifts. The device implements the M680x0 instruction set fully, supporting BERR/BR/ACK arbitration, bus snooping for SMP, and an interrupt controller. Its on-die FPU runs double-precision operations at sub-microsecond latency and includes an operand pipelining mechanism typical of the 68060 family. Typical applications include VMEbus single-board computers (SBCs), industrial automation controllers, military/aerospace avionics, Amiga/Atari-compatible accelerator boards, and telecom base stations built around legacy M68k firmware. At 50 MHz it executes Dhrystone 1.1 at approximately 60 MIPS. Designers must implement a bus arbiter, reset controller, and clock source (50 MHz fundamental or 2x with internal PLL); the 'EC' lacks the PMMU unit found on the full MC68060, so systems requiring virtual memory must use the MC68060RC50 or add a discrete MMU. Lead-free / RoHS status: per distributor data this BEPGA variant contains lead, so it is RoHS non-compliant by default. When designing with this part, treat thermal management as the primary constraint: the 206-pin BEPGA dissipates up to 7 W at full load with no integrated heatsink, so a heatsink and forced-air cooling are mandatory in enclosed chassis. The 5 V tolerant I/O simplifies legacy peripheral glue logic, but 5 V inputs on 3.3 V rails must be current-limited. Cache coherency for multi-master designs requires bus snooping enabled via the SNOOP pin and proper BR/BG arbitration.

RFQ İletişim
MC68EC060RC66 - 32-Bit 66MHz 68060 MPU w/ Cache | NXP
MC68EC060RC66

MC68EC060RC66 - 32-Bit 66MHz 68060 MPU w/ Cache | NXP

The NXP Semiconductors MC68EC060RC66 is a 32-bit reduced-instruction-set (CISC actually, M68000 family) microprocessor in the 680x0 family, operating at 66 MHz with on-chip instruction and data caches, housed in a 206-pin BEPGA (47.25 x 47.25 mm) ceramic pin-grid-array package. It is the cost-reduced (no MMU) EC variant of the full MC68060 and is designed for embedded control, industrial, and legacy M68K applications where software compatibility with the 68000/68020/68030/68040 instruction set is mandatory. A microprocessor (MPU) is the central processing unit of a computer system, integrating the ALU, register file, control logic, cache, and bus interface onto a single die. The MC68EC060 belongs to the M680x0 (Motorola 68000) family, a CISC architecture that walks UP the taxonomy as follows: 68060 MPU -> 32-bit CISC microprocessor -> M68000 family CPU -> embedded microprocessor -> integrated circuit. This hierarchy, combined with the EC suffix (no memory management unit), positions the part as an upgrade path for legacy 68030/68040 designs that do not need MMU-driven virtual memory. Key features include a 66 MHz core clock, 8 KB four-way set-associative instruction cache plus 8 KB data cache, hardware multiply and divide, a 32-bit internal data bus, and a 32-bit external data bus with dynamic bus sizing for 8/16/32-bit peripherals. The device operates from a 3.3 V supply (Vcc) and 5 V tolerant I/O on selected pins, drawing roughly 4.5 W typical at full clock. Integrated peripherals include a DMA controller, two serial channels, a parallel I/O port, timers, and an interrupt controller. Typical applications include legacy VMEbus single-board computers, industrial automation controllers using the VxWorks or OS-9 real-time operating system, Avionics mission computers that were historically 68060-based, point-of-sale terminals, medical imaging systems requiring deterministic M68K performance, and long-lifecycle defense/military upgrades. The wide third-party software ecosystem (Linux/m68k, NetBSD, FreeRTOS ports) makes it a drop-in upgrade for existing 68040 boards. When designing with the MC68EC060RC66, ensure the BEPGA socket or PCB land pattern accepts the 47.25 x 47.25 mm ceramic PGA footprint. Provide proper decoupling per the manufacturer reference design and validate thermal performance because the ceramic PGA package has higher thermal resistance than plastic QFP equivalents; a heatsink or forced airflow is recommended in enclosed industrial enclosures. This page synthesizes legacy distributor stock, drop-in pin-compatible variants (MC68EC060RC50, RC75, full MC68060RC66), and practical design notes not found in the original Freescale/Motorola datasheet, helping engineers manage long-lifecycle 68060 designs without PCB rework.

RFQ İletişim
MC68EC060ZU75 - 75MHz 32-bit M680x0 MPU, 304-TBGA | NXP / Freescale
MC68EC060ZU75

MC68EC060ZU75 - 75MHz 32-bit M680x0 MPU, 304-TBGA | NXP / Freescale

The NXP MC68EC060ZU75 is a 75 MHz, 32-bit M680x0 family microprocessor IC supplied in a 304-ball TBGA (31x31 mm) package. As the embedded-controller variant of the superscalar M68060 architecture, it integrates a 32-bit integer core, an 8 KB unified instruction/data cache, a memory management unit (MMU), and dual instruction pipelines capable of issuing up to two instructions per clock cycle. A microprocessor (MPU) is a single-chip CPU that fetches, decodes, and executes instructions from external memory and is the central processing unit of an embedded computing system. Within the wider MPU hierarchy, the M68k family sits alongside PowerPC, ARM, and MIPS as one of the canonical 32-bit CISC/RISC architectures; the MC68EC060ZU75 belongs to the M680x0 family, specifically the EC060 embedded-controller sub-line of the superscalar sixth-generation 680x0 series. It is targeted at systems that need raw M68k software compatibility without the FPU or PMMU requirements of the full MC68060. Key features include 75 MHz core clock, 3.3 V I/O and core supply, 304-ball TBGA (also listed as 304-LBGA, 31x31 mm), superscalar dual-instruction issue, branch prediction with a 256-entry branch target cache, integrated 8 KB unified cache, and a 32-bit external data bus. Compared with earlier 68040 designs the EC060 typically delivers roughly 2-3x integer Dhrystone MIPS at equivalent clock, while keeping binary compatibility with the 68k instruction set. The architecture is a 4-stage superscalar pipeline with out-of-order completion, supporting the full M680x0 user instruction set. Burst-mode memory transfers, hardware MMU, and integrated cache reduce external bus traffic, which is critical at 75 MHz on a 32-bit external bus where un-cached accesses dominate throughput. Typical applications include industrial control, legacy M68k embedded controllers, avionics retrofits, telecommunications line cards, point-of-sale terminals, and VME/cPCI single-board computers that maintain a 68k software base. The 3.3 V supply and high pin-count TBGA make it a drop-in part for existing 68060 board designs that do not require the on-die FPU. When designing with the MC68EC060ZU75, pay attention to TBGA PCB layout - the 1.27 mm ball pitch demands four or more routing layers with microvia technology to escape the inner ball rows. Provide robust 3.3 V decoupling, and verify that any heatsink thermal solution accommodates the 31x31 mm package footprint. This page synthesises distributor pricing, same-package drop-in alternatives (including same-speed/lower-speed 68060 variants), and practical layout guidance not found in the manufacturer datasheet alone.

RFQ İletişim
MC68EN302AG20BT - 20MHz Ethernet 68K MPU, 144-LQFP | NXP
MC68EN302AG20BT

MC68EN302AG20BT - 20MHz Ethernet 68K MPU, 144-LQFP | NXP

The NXP Semiconductors MC68EN302AG20BT is a multi-channel communications processor (also known as MC68EN302 or "EN302") based on the M68000 microprocessor core, integrating three serial communications channels (SCC) plus a dedicated 10 Mbps Ethernet channel compliant with IEEE 802.3. It is housed in a 144-pin LQFP (20x20 mm) package and operates at 20 MHz, with 1 core on an 8/16-bit external data bus. An embedded microprocessor (MPU) is an integrated processor designed to be the central computing element of an embedded system, combining a CPU, on-chip peripherals, and memory control in a single device. Within the broader hierarchy, the MC68EN302 sits in the sub-family of integrated communications processors, descended from the Motorola/Freescale 683xx family of M68K CPUs - a product lineage that evolved from the MC68000 microprocessor introduced in 1979. The device is intended for embedded networking equipment where deterministic serial communications, on-chip Ethernet MAC, and low BOM cost outweigh raw compute throughput. Key features include an M68000-family CPU core running at 20 MHz, three independent SCC serial channels (usable for UART, HDLC, BISYNC, transparent modes), a separate Ethernet channel with full IEEE 802.3 MAC support and on-chip transmit/receive descriptors that offload bus bandwidth, on-chip DRAM controller, timers, parallel I/O, and interrupt controller. The Ethernet channel supports up to 10 Mbps data rates and uses the "68302" style programming model familiar to legacy firmware developers. Architecturally, the EN302 separates the CPU-side system bus from the peripheral-side bus, so descriptor-based DMA engines move packet data between the Ethernet channel and system memory without CPU intervention. This dual-bus design is critical for sustaining 10 Mbps line-rate throughput while leaving CPU cycles available for protocol processing (TCP/IP stack, PPP, or proprietary industrial protocols) running from external memory. Typical applications include industrial Ethernet routers, ISDN terminal adapters, legacy serial-to-Ethernet protocol converters, factory automation gateways, point-of-sale terminals, and telecom access equipment. The on-chip Ethernet MAC plus multi-protocol SCCs make it a single-chip solution for designs that previously required a discrete CPU plus external Ethernet controller plus UART/HDLC ASIC. When designing with this part, verify that firmware is rebuilt against the 68302 programming model and that the BSD-style Ethernet drivers target the on-chip descriptor ring interface. Supply voltage, junction temperature, and DRAM controller timing parameters not explicitly listed in this product page should be confirmed against the manufacturer datasheet before board bring-up. This page synthesizes distributor stock data, key parametric differences versus other M68K members, and practical design considerations specific to the EN302 variant - information not aggregated on any single manufacturer or distributor product page.

RFQ İletişim
MC68EN360AI25L - QUICC M683xx 32-Bit MPU 25MHz | NXP
MC68EN360AI25L

MC68EN360AI25L - QUICC M683xx 32-Bit MPU 25MHz | NXP

The NXP (formerly Motorola/Freescale) MC68EN360AI25L is a 32-bit embedded microprocessor from the M683xx (QUICC, ETHRN) family, integrating a CPU32+ core with on-chip Ethernet communications peripherals. It operates at 25 MHz, runs from a 5 V supply, and is housed in a 240-pin FQFP (32 x 32 mm) surface-mount package. The 'EN' designator indicates the Ethernet-enabled variant of the MC68360 QUICC (Quad Integrated Communication Controller) family. An embedded microprocessor (MPU) is a complete CPU on a single IC die, normally combined with memory-mapped peripherals, designed to execute firmware and oversee hardware in a system. The M683xx/QUICC product line combines a CPU32+ 32-bit core with dedicated communication engines - the MC68EN360 extends that family by adding a built-in Ethernet controller alongside the standard QUICC peripherals. Within the broader taxonomy, this places the device as an embedded MPU -> 32-bit MPU -> communications MPU -> industrial/edge-networking MPU -> integrated communication controller. Key features include a 32-bit CPU32+ core, 25 MHz maximum operating frequency, an integrated 10 Mbps Ethernet MAC, four serial communication controllers (SCCs) supporting HDLC/SDLC, UART, BISYNC, and transparent protocols, two serial management controllers (SMCs), a parallel interface, and a system integration module (SIM60) with interrupt controller, chip-select logic, and bus monitor. The 240-FQFP package provides a large land pattern suitable for industrial communication gateway hardware. The MC68EN360AI25L architecture unites a CISC 68000-family core with a dedicated RISC-based communications processor module (CPM) running at the same clock, offloading protocol processing from the CPU32+. This dual-engine approach is the architectural reason the QUICC family dominated networking, telecom, and industrial control designs through the 1990s and 2000s, and still supports long-lifecycle installed bases today. Typical applications include industrial communication gateways, telecom routers, edge-networking appliances, factory-floor protocol converters, and SCADA controllers. The integrated Ethernet SCC, combined with up to four protocol-capable SCCs, makes it ideal for bridging legacy RS-232/RS-485 serial devices to TCP/IP networks in brownfield industrial systems. When designing with this device, note that it is a legacy part on the NXP End-of-Life register, so long-term firmware maintenance, drop-in alternates, and second-source sourcing should be planned up front. Confirm supply continuity through authorized distributors and consider cold-fire successor families only when a redesign is feasible. This page synthesizes authorized distributor pricing, drop-in same-family alternates, and practical design notes for long-lifecycle M68K systems that are not always covered in the original datasheet alone.

RFQ İletişim
MC68EN360AI33L-FR - 33MHz CPU32+ QUICC MPU 240-FQFP | Freescale
MC68EN360AI33L-FR

MC68EN360AI33L-FR - 33MHz CPU32+ QUICC MPU 240-FQFP | Freescale

The Freescale (NXP) MC68EN360AI33L-FR is a CPU32+ microprocessor IC from the M683xx QUICC (Quad Integrated Communication Controller) family that integrates a single 32-bit core running at 33 MHz with an on-chip Communications Processor Module (CPM), housed in a 240-pin FQFP (32x32 mm) package. It is built on a 0.57 um CMOS process and operates from a 5 V supply, distinguishing it from the 3.3 V "EN" variant. The device combines the CPU32+ core with the CPM coprocessor, four serial communications controllers (SCCs), two serial management controllers (SMCs), one serial peripheral interface (SPI), and a 10 Mbps Ethernet MAC, making it a complete system-on-chip for embedded networking. What is a QUICC microprocessor? The QUICC is an integrated communications controller family that fuses a general-purpose CPU32+ microprocessor with a dedicated RISC-based Communications Processor Module offloading serial and networking tasks. In the system hierarchy it sits between microcontroller units (MCUs) and dedicated ASIC/SoC solutions, targeted at routers, bridges, telecom equipment, and industrial control nodes that need deterministic Ethernet and serial performance without an external MAC. Key features include 1 core 32-bit data path, 33 MHz CPU32+ instruction throughput, a CPM offload engine with 10 Mbps Ethernet, and four SCC channels supporting HDLC/SDLC/PPP/UART framing. The 240-FQFP package is a surface-mount fine-pitch QFP measuring 32x32 mm, suitable for multilayer industrial backplanes. The 5 V core supply and 5 V tolerant I/O simplify integration into legacy telecom backplanes that standardize on 5 V rails rather than 3.3 V. Architecturally, the CPU32+ core is a 32-bit M68k-family CPU with a unified instruction and data programming model, while the CPM is a separate RISC engine (CP) that handles all serial DMA, SCC/SMC framing, and Ethernet packet buffering without interrupting the main CPU. This dual-engine approach yields deterministic serial latency under heavy network load, an important property for HDLC/PPP links and protocol bridges. The integrated 10 Mbps Ethernet MAC and serial glue allow glue-free connection to PHYs and transceivers. Typical applications include 10/100 Mbps Ethernet bridges/routers, telecom line cards (ISDN, T1/E1), HDLC/PPP frame relay equipment, industrial serial servers, and legacy 5 V M68k embedded control. The package size and pin count limit it to high-density industrial designs where the CPM's offload is more valuable than a more compact footprint. When designing with this part, note its End-of-Life status: NXP's product page marks MC68EN360AI33L as "Not For New Designs" and the -FR variant is supplied exclusively by authorized aftermarket distributors for long-life programs. Always validate thermal and signal-integrity margins against the manufacturer's datasheet before finalizing a new design on this part, and consider the MC68EN360AI33L or MC68360 family derivatives if a current-production alternative is required. This page synthesizes distributor pricing, package and pinout data, drop-in alternatives, and practical design notes that are not collected together in the manufacturer datasheet.

RFQ İletişim
MC68EN360CRC25L - 25MHz QUICC M683xx 32-Bit MPU | NXP
MC68EN360CRC25L

MC68EN360CRC25L - 25MHz QUICC M683xx 32-Bit MPU | NXP

The NXP MC68EN360CRC25L is a 25 MHz, 32-bit M683xx microprocessor with an integrated Ethernet-aware Communications Processor Module (CPM), packaged in a 241-pin PGA (47.24x47.24 mm). It belongs to the QUICC family (Quad Integrated Communication Controller) with a CPU32+ core, one core, and on-chip peripherals including four SCC channels (one of which is dedicated to 10 Mbps Ethernet), Ethernet support, DRAM controller, and glue logic for embedded networking designs. Background. An MPU (microprocessor unit) in the M68K/ColdFire lineage combines a CPU core with peripheral subsystems on a single die, enabling a system-on-chip approach without external co-processors. The MC68EN360CRC25L sits in the product hierarchy as: 32-bit MPU -> M683xx family -> QUICC communications controllers -> embedded networking MPU. It is optimized for designers who need deterministic serial-channel handling and an integrated 10 Mbps Ethernet MAC without resorting to a discrete PHY/MCU combination. Key features include a CPU32+ core at 25 MHz, an integrated 10 Mbps Ethernet channel fully compliant with IEEE 802.3, four serial communication channels (SCCs), a DRAM controller with glue logic, 5 V supply operation, and a 241-pin BEPGA through-hole package that supports legacy backplane designs in telecom and industrial control. Technical depth. The device implements a RISC-style CPU32+ core with 32-bit internal architecture, fabricated on a 0.57 micron process. The Ethernet MAC is implemented in the CPM and connects to an external PHY via MII/AUI; the device also incorporates a separate MC68160A-style Ethernet transceiver interface capability, which is why some listings reference the MC68160A companion. Its QUICC architecture decouples communications handling from the CPU, allowing simultaneous DMA-driven serial traffic while the CPU runs the application stack. Typical applications include 10 Mbps Ethernet-attached routers and bridges, ISDN terminal adapters, industrial serial-to-Ethernet gateways, telecom line cards, and legacy 683xx-based control planes. The 241-pin PGA suits production boards already designed for the QUICC footprint. Design consideration. Plan the PCB for the 241-pin grid-array with adequate thermal relief and decoupling; the device is 5 V only, so level translation is required when interfacing to modern 3.3 V peripherals. For new designs consider the MC68360 family with lower voltage or the ColdFire MCF527x/528x as migration paths. This page synthesizes distributor stock, parametric alternatives, and design notes not found in the standalone datasheet.

RFQ İletişim
MC68EN360VR25L - 25MHz QUICC M683XX MPU | NXP | 357-BGA
MC68EN360VR25L

MC68EN360VR25L - 25MHz QUICC M683XX MPU | NXP | 357-BGA

The NXP MC68EN360VR25L is a 25 MHz, 32-bit integrated microprocessor from the M68300 (QUICC) family, housed in a 357-ball plastic BGA (PBGA, 25x25 mm) package. The MC68360 Quad Integrated Communication Controller (QUICC) is a versatile one-chip integrated microprocessor and peripheral combination family that can be used in a variety of controller applications, particularly networking and telecom equipment. An MPU (Microprocessor Unit) of this class is a single-chip processor integrating a CPU core with on-chip memory, system integration, and dedicated peripheral modules. The M683XX family derives from the original Motorola 68000 architecture and is positioned within the broader taxonomy of microprocessors -> 32-bit embedded processors -> communication controllers -> power-management/connectivity silicon. The QUICC family is synonymous with Motorola/NXP's networking-oriented microprocessor line, designed for routers, bridges, and high-speed serial communications. Key features of the MC68EN360VR25L include a CPU32+ core running at 25 MHz, an integrated communications processor module (CPM), multiple serial channels (including Ethernet), and on-chip system integration. The 357-BGA package provides a high-density interconnect surface for the device's wide parallel system bus and serial interface pins. The part operates over the commercial temperature range and supports typical 5 V operation as specified by the original Motorola M68300 family datasheet. At the architectural level, the MC68EN360VR25L combines a CPU32+ processor with the CPM (Communications Processor Module) that offloads serial handling tasks — including HDLC, UART, and Ethernet MAC — from the main CPU. This dual-engine architecture was ahead of its time, allowing deterministic handling of multiple serial channels alongside general-purpose embedded control code, a pattern that influenced later PowerQUICC devices. Typical applications for the MC68EN360VR25L include ISDN routers, remote access concentrators, frame-relay access devices, and industrial control with serial networking. Its combination of Ethernet and HDLC capability made it a popular choice in early 1990s and 2000s customer-premises equipment. When designing with this device, pay attention to the 357-ball BGA layout: PCB routing requires via-in-pad or dog-bone escapes on a multi-layer board, and proper thermal via placement under the BGA is essential. Decoupling capacitors should be placed as close as practical to each power/ground ball pair to maintain signal integrity at the 25 MHz system bus speed. This page synthesizes distributor pricing, drop-in same-package alternatives (including the MC68EN360ZP25L and MPC860EN variants), and practical BGA-handling design notes not found in the manufacturer datasheet.

RFQ İletişim
MC68EN360VR33L - 33MHz M683xx QUICC CPU32+ MPU, 357-PBGA | NXP
MC68EN360VR33L

MC68EN360VR33L - 33MHz M683xx QUICC CPU32+ MPU, 357-PBGA | NXP

The NXP Semiconductors (formerly Motorola/Freescale) MC68EN360VR33L is a 33 MHz, 32-bit M683xx-family CPU32+ microprocessor IC housed in a 357-ball PBGA (25x25 mm) package, integrating Ethernet and communications peripherals. The 'EN' suffix denotes the integrated 10/100 Ethernet MAC, while 'VR' denotes the plastic BGA package, '33' is the 33 MHz bus frequency, and 'L' indicates low-voltage/extended temperature screening. The part operates from a single 5 V supply and combines a CPU32+ core with the QUICC (QUad Integrated Communication Controller) engine, which is a multi-channel communications-processor module with a separate RISC microcontroller optimized for HDLC, transparent, and asynchronous serial protocols. A microprocessor (MPU) is the central processing unit of an embedded system, integrating an arithmetic-logic unit, register file, instruction decoder, memory-management unit, and peripheral controllers onto a single die. The MC68360 family sits in the hierarchy: MPU -> embedded processor -> 32-bit CISC/RISC hybrid (CPU32+ core with RISC comm engine) -> communications controller. It is engineered for telecom, datacom, and industrial-control applications where deterministic serial-channel handling is required alongside a general-purpose host CPU. Key features include a 32-bit CPU32+ core with 4 GB address space, dedicated RISC communications processor supporting SCCs (serial communication channels), an integrated 10/100 Ethernet MAC with MII interface, dual 8 Kbyte instruction/data caches, DRAM controller, DMA controller, timers, and parallel I/O. The 357-PBGA package uses a 25x25 mm substrate with 1.27 mm pitch, and a typical operating junction temperature range of -40C to +85C. The architecture offloads protocol processing from the host CPU, freeing it for application-layer tasks. The CPU32+ core is binary-compatible with the M68k instruction set, enabling reuse of legacy 68000-family code and toolchains, while the QUICC engine independently manages serial framing. Compared with earlier MC68360 variants, the 'EN' version integrates Ethernet, reducing external PHY-controller glue logic and PCB area. Compared with MC68360ZQ33L, this part shares the same 33 MHz CPU32+ core but is offered in the plastic PBGA 'VR' package versus ceramic 'ZQ'. Typical applications include 10/100 Ethernet-attached routers, multi-port serial bridges, ISDN terminal adapters, industrial PLCs with Ethernet uplinks, frame-relay access devices, and legacy telecom line cards. The integrated Ethernet MAC plus multiple SCCs makes the device a one-chip solution for compact embedded communications products. When designing with the MC68EN360VR33L, allocate adequate PCB area for the 25x25 mm 357-BGA and use at least four PCB layers with a continuous ground plane beneath the package for thermal dissipation and signal integrity. Decouple all VCC pins with 0.1 uF ceramic capacitors placed within 5 mm of each ball, and follow the Motorola QUICC hardware-design checklist for SI on the MII bus. Verify that all unused balls are tied per the datasheet's 'no-connect' recommendations.

RFQ İletişim
MC68EN360ZP33L - CPU32+ 33MHz M683xx Microprocessor | NXP
MC68EN360ZP33L

MC68EN360ZP33L - CPU32+ 33MHz M683xx Microprocessor | NXP

The NXP MC68EN360ZP33L is a CPU32+ microprocessor IC from the M683xx family, integrating a 32-bit core running at 33 MHz with on-chip communication peripherals in a 357-ball PBGA (25x25 mm) package. It features a 5 V supply rail, a single 32-bit CPU32+ core, and is designed for embedded networking and communications designs. The MC68EN360 series is also known as the QUad Integrated Communication Controller (QUICC), combining a CPU32+ core with communication co-processors on a single die. The 357-PBGA package is a plastic ball-grid-array surface-mount form factor that requires reflow soldering and a 1.27 mm or finer pitch PCB land pattern. An M683xx microprocessor is a family of 32-bit embedded processors originally developed by Motorola (now NXP/Freescale). The 'CPU32+' is an enhanced variant of the original CPU32 core, adding additional addressing modes and improved exception handling for embedded control. The broader M683xx hierarchy runs: CPU32+ -> M683xx -> ColdFire/Freescale 32-bit embedded microprocessors. These devices sit in the wider taxonomy of microprocessors -> integrated circuits -> semiconductors, and are typically deployed where deterministic real-time response is required alongside serial communications. Key features include the integrated QUICC communications engine (typically containing multiple SCCs, SMCs, and a Serial DMA channel), 4 KB of unified cache for instruction and data, and a 32-bit system bus. The device targets 5 V designs and supports both M68000 and CPU32+ instruction sets. Per the NXP MC68360 product brief, this combination was intended to remove an external communications controller from a board, reducing BOM cost and freeing the CPU32+ core to focus on the application layer. Note that this specific ZP33L variant is supplied as a 357-ball PBGA at commercial temperature grade. Typical applications include industrial routers, telecom control boards, ISDN terminal adapters, industrial Ethernet bridges, and legacy embedded control systems where the QUICC engine handles low-level serial framing. The wide bus and DMA channels allow line-rate processing of HDLC or transparent serial streams without CPU intervention. The 5 V rail is compatible with telecom and industrial backplane supplies common in the late 1990s and early 2000s. When designing with this part, allocate sufficient PCB real estate for the 25x25 mm BGA and use at least 4-layer routing with via-in-pad for the inner balls. Decoupling must follow the NXP reference design: place 0.1 uF and 10 uF capacitors within 5 mm of every supply ball. Plan for JTAG access via the on-chip debug port for boundary-scan and in-system programming during production test. This page synthesizes NXP/Freescale datasheet specifications, current distributor pricing, and drop-in package-matched alternatives not collated in the original manufacturer datasheet. Where the official datasheet is paywalled, this synthesis helps engineers validate second-source availability for long-life industrial designs.

RFQ İletişim
MC68EN360ZQ25VL - 25MHz QUICC M683xx 32-Bit MPU | NXP 357-PBGA
MC68EN360ZQ25VL

MC68EN360ZQ25VL - 25MHz QUICC M683xx 32-Bit MPU | NXP 357-PBGA

The NXP MC68EN360ZQ25VL is a CPU32+ M683xx series 32-bit microprocessor operating from a 3.3V supply at 25 MHz, integrated into a 357-ball PBGA (25x25 mm) package. The device combines a 32-bit CPU core with the QUICC (Quad Integrated Communication Controller) peripheral set, including Ethernet and multi-channel serial I/O for embedded networking applications. What is a microprocessor IC? A microprocessor (MPU) is an integrated circuit that contains a central processing unit capable of executing instructions fetched from external memory. The MC68EN360 family belongs to the M683xx ColdFire/CPU32+ lineage, which evolved from the Motorola 68000 architecture into a family of integrated microprocessors with on-chip peripherals for communications and embedded control. Key features include a single 32-bit core at 25 MHz, an integrated Ethernet media access controller (ETHRN) for 10 Mbps networking, HDLC/serial communication channels, and a DRAM controller. The part is offered in a 357-pin PBGA (also referred to as 357-BBGA) package measuring 25x25 mm, supplied in tray packaging with commercial temperature grading per the verified data. The MC68EN360 integrates the CPU32+ core with the QUICC peripheral engine, allowing simultaneous execution of communication tasks alongside user code. The 0.57-micron process geometry and 25 MHz clock frequency place this part in the legacy Freescale/NXP embedded networking category, suited for telecom, industrial, and routing equipment designs of the late 1990s and early 2000s. Typical applications include LAN routers and bridges, telecom switching equipment, industrial serial communication controllers, and embedded networking appliances. The on-chip Ethernet MAC reduces external component count compared to CPU-only designs of the same era. When designing with this part, verify PCB layout tolerances for the 1.27 mm pitch BGA balls and confirm thermal vias under the package. The legacy 0.57-micron process means the device is not low-power by modern standards; ensure the power supply decoupling network matches the manufacturer's reference schematic. This page synthesizes distributor pricing (as of 2026-10-17), drop-in alternatives including MCF5282CVM80 and MC68MH360ZQ25VL, and practical engineering notes not found in the manufacturer datasheet alone.

RFQ İletişim
MC68EN360ZQ25VL-FR - M683xx QUICC CPU32+ 25MHz MPU | NXP
MC68EN360ZQ25VL-FR

MC68EN360ZQ25VL-FR - M683xx QUICC CPU32+ 25MHz MPU | NXP

The NXP MC68EN360ZQ25VL-FR is a CPU32+ Microprocessor IC from the M683xx QUad Integrated Communication Controller (QUICC) family, operating at 25 MHz with a 32-bit core in a 357-pin PBGA (25x25) package. It integrates a versatile one-chip microprocessor and peripheral combination that targets communication-intensive embedded controller applications. The part is supplied in tray packaging. What is a QUICC microprocessor? QUICC (Quad Integrated Communication Controller) is Motorola/Freescale/NXP's flagship 32-bit communications-controller architecture that combines a CPU32+ processor core with the Communications Processor Module (CPM). The CPM offloads serial-channel handling from the CPU through dedicated RISC engines (CP), enabling concurrent management of multiple HDLC/SDLC, UART, and Ethernet channels without burdening the main core. The QUICC family sits within the broader taxonomy: microprocessor (MPU) -> embedded microprocessor -> communications controller -> system-on-chip. This positioning makes QUICC devices the forerunners of modern SoCs with integrated networking peripherals. Key features of the MC68EN360ZQ25VL-FR include the CPU32+ 32-bit core, integrated DRAM controller, 10 Mbps Ethernet MAC, four serial communications controllers (SCCs) supporting HDLC/SDLC/UART protocols, and a system integration module (SIM60). The 25 MHz clock speed delivers approximately 25 MIPS of processing throughput, and the 3.3V supply keeps power dissipation manageable for embedded systems of the late 1990s / early 2000s era. The architecture employs a Harvard-style split between the CPU32+ core and the CPM. The CPM contains its own RISC processor, serial channel buffers, and timing controllers, allowing the chip to sustain full-duplex communication on all four SCCs plus Ethernet simultaneously with negligible CPU intervention. Memory is configured via the SIM60 with support for DRAM, SRAM, and flash, plus eight chip selects for external peripherals. Typical applications include ISDN router/gateway designs, frame-relay access devices, multi-port serial communication concentrators, industrial control systems with networking, and legacy telecommunications infrastructure. The integrated 10 Mbps Ethernet MAC and four SCCs make it particularly suited to early-internet-edge routers, DSLAM line cards, and protocol bridges. When designing with the MC68EN360ZQ25VL-FR, engineers should follow the layout guidelines in the NXP/Freescale application notes for BGA decoupling and high-speed signal routing. The 357-ball PBGA is a high-pin-count package that demands multilayer PCB stack-up with dedicated power and ground planes; failure to observe signal-integrity recommendations can cause CPM timing violations. This page synthesizes distributor stock levels, drop-in same-package alternatives, RoHS status and application guidance not consolidated in the manufacturer datasheet alone, helping engineers evaluate lifecycle risk for this legacy communications MPU.

RFQ İletişim
MC68EN360ZQ33L - 33MHz QUICC Ethernet MPU | NXP | BGA-357
MC68EN360ZQ33L

MC68EN360ZQ33L - 33MHz QUICC Ethernet MPU | NXP | BGA-357

The NXP MC68EN360ZQ33L is a 32-bit microprocessor from the M683xx (CPU32+) family, integrating a 33 MHz CPU core with the QUICC (Quad Integrated Communication Controller) engine and a 10/100-capable Ethernet MAC in a single 357-ball PBGA package. It combines a 4K-byte instruction cache, 4K-byte data cache, MMU, and a versatile peripheral set including SCCs, SMCs, an SPI, an I2C controller, a parallel port, and a DRAM controller, making it a one-chip networking and control solution. A microprocessor (MPU) in the M683xx family is a 32-bit CISC/RISC processor originally derived from the Motorola 68000 lineage, designed for embedded networking, telecom, and industrial control workloads. It belongs to the broader category of microprocessors -> embedded processors -> communication controllers, sitting hierarchically below application processors and above simple microcontrollers in capability and integration. The "EN" in MC68EN360 denotes the integrated Ethernet MAC, while "ZQ33L" encodes the 357-BGA package, 33 MHz clock, and low-voltage/legacy process variant. Key features include a 33 MHz CPU32+ core with hardware multiply/divide, an integrated 10/100 Ethernet MAC (Fast Ethernet controller), four Serial Communication Controllers (SCCs) supporting HDLC/SDLC, UART, transparent modes, BISYNC, and Ethernet, plus two Serial Management Controllers (SMCs), a Serial Peripheral Interface (SPI), an I2C bus interface, a DRAM controller supporting up to 32 address bits, a 16-channel DMA, timers, and a parallel I/O port. The device operates from a single 5V supply and is housed in a 357-ball Plastic BGA (25 x 25 mm). The QUICC engine architecture offloads communication processing from the CPU32+ core, allowing line-rate handling of multiple serial protocols concurrently. With 4K+4K on-chip caches, MMU, and burst-mode memory support, it can sustain deterministic throughput for routing, bridging, and protocol-conversion tasks typical of legacy telecom and industrial routers, bridges, and embedded networking appliances. Typical applications include legacy routers and bridges, industrial Ethernet gateways, telecom protocol converters, WAN access concentrators, serial-to-Ethernet device servers, and point-of-sale terminals. The integrated Ethernet MAC and multi-protocol SCCs make it well-suited to systems requiring concurrent Ethernet and legacy serial traffic handling. When designing with this part, use Rochester Electronics or NXP/Freescale franchised stock because the part is mature and production is limited; verify thermal management for the 357-BGA, ensure the 5V supply is well-decoupled, and confirm the firmware toolchain (CPU32+/68K GCC or Diab) supports your protocol stack. The part is RoHS non-compliant and contains lead, so conformal coating or lead-free revalidation is required for new RoHS-mandated designs.

RFQ İletişim
MC68F375BGMVR33 - 33MHz 32-Bit 256KB Flash MCU | NXP
MC68F375BGMVR33

MC68F375BGMVR33 - 33MHz 32-Bit 256KB Flash MCU | NXP

The NXP Semiconductors MC68F375BGMVR33 is a 32-bit single-core ColdFire M68300 microcontroller operating at 33 MHz, with 256 KB of flash program memory in a 217-PBGA package measuring 23 x 23 mm. The device combines a 3.3 V supply requirement, CANbus, SPI, UART/USART connectivity, PWM, watchdog, power-on reset, and 48 I/O functions in one automotive-oriented embedded-control package. What is a 32-bit microcontroller? A microcontroller is a semiconductor device that integrates a processor core, nonvolatile program memory, data memory, and peripherals on one integrated circuit. This ColdFire controller belongs to the microcontroller, embedded processor, 32-bit microprocessor, and embedded-control hierarchy. It executes firmware from flash memory and uses its communication and timing peripherals to control external automotive, industrial, or communications equipment. The verified product information identifies a CPU32 M683xx core, 33 MHz operating speed, and 256 KB organized as 256K x 8 flash. Its listed peripheral set includes CANbus, SPI, UART/USART, power-on reset, pulse-width modulation, and a watchdog timer. A 3.3 V automotive configuration makes the part relevant to embedded systems that require a 32-bit architecture, on-chip flash, and multiple serial interfaces without an external memory bus. The MC68F375 family is based on the ColdFire architecture, commonly identified in source data as M68300 or CPU32 M683xx. At 33 MHz, the controller provides substantially more processing capability than an 8- or 16-bit MCU while retaining dedicated embedded peripherals. The verified data does not specify RAM size, supply-voltage tolerances, transceiver details, or the exact allocation of the 48 I/O pins, so those values must be confirmed in the manufacturer documentation before design release. Potential uses include automotive body and chassis control modules, CAN-connected node controllers, industrial automation equipment, serial gateways, and embedded test systems. CANbus support is useful for distributed networks, while SPI and UART/USART permit attachment to sensors, transceivers, memory devices, and service interfaces. PWM can support actuator or signaling functions, and the watchdog timer helps recover the controller after a software or hardware fault. The principal design concern is package complexity. A 217-PBGA footprint requires a multilayer PCB, fine-pitch routing, controlled escape routing, and assembly capability suited to large-area grid arrays. Before starting a new design, engineers should verify the obsolete-product status, exact pinout, electrical limits, flash programming method, peripheral multiplexing, and software-device revision in the official datasheet. This page consolidates the verified distributor specifications, lifecycle information, package details, sourcing references, and compatibility caveats for the MC68F375BGMVR33. It deliberately distinguishes documented values from missing technical data and does not treat generic search results as proof of pin-compatible replacements.

RFQ İletişim
MC68F375BGMZP33 - CPU32 M683xx 33MHz 256KB Flash MCU | NXP
MC68F375BGMZP33

MC68F375BGMZP33 - CPU32 M683xx 33MHz 256KB Flash MCU | NXP

The NXP MC68F375BGMZP33 is a 32-bit CPU32 microcontroller from the M68300/68HC16 modular family, integrating 256KB of Flash memory, 8KB SRAM, and 2KB additional RAM in a 217-pin PBGA package (23x23 mm). It operates at a 33 MHz CPU clock speed and is targeted at embedded industrial, automotive, and consumer control applications. According to NXP product information, this part is in the 'No Longer Manufactured' status, which is critical to note for long-term procurement planning. A 32-bit microcontroller (MCU) is an integrated circuit containing a 32-bit CPU core, volatile and non-volatile memory, and programmable peripherals designed for embedded control tasks. Within the broader taxonomy, an MCU belongs to the semiconductor > integrated circuit > microcontroller > 32-bit microcontroller hierarchy. The M68300/68HC16 family uses a modular architecture in which functional blocks (CPU, memory, timers, serial, I/O) are connected via an internal intermodule bus (IMB), enabling NXP to instantiate many part numbers from a shared silicon platform. Key features of the MC68F375BGMZP33 include a 32-bit CPU32 core, 256KB on-chip Flash, 8KB SRAM plus 2KB additional RAM, 33 MHz system clock, and 217-ball PBGA packaging rated for commercial temperature grade. The Flash memory allows in-application reprogramming, simplifying firmware updates in the field. The 23x23 mm PBGA package provides high-density board mounting while supporting the large number of I/O pins required by complex embedded systems. The CPU32 architecture is a 32-bit extension of the M68k family and executes the same instruction set as the Motorola 68020, providing a migration path for legacy 68k code. The modular intermodule bus (IMB) means that peripheral selection is part-aware, and the device integrates modules such as a system integration module, timers, serial interfaces, and a queued serial module for communication. According to the manufacturer datasheet, designers should review the family reference manual for detailed peripheral mapping. Typical applications include industrial automation controllers, automotive body and chassis controllers, point-of-sale terminals, and complex embedded systems that previously used the 68k architecture. The 256KB Flash and 8+2KB RAM configuration suits systems with moderate code size and real-time data buffering requirements. When designing with this part, note that it is now in NXP's 'No Longer Manufactured' lifecycle. Engineers should verify long-term supply, consider drop-in replacements, or evaluate migration to a newer Kinetis or ColdFire+ family MCU. Confirm operating temperature grade with your distributor before sourcing, as the 'ZP33' suffix indicates a 33 MHz speed grade within the package. This page synthesizes distributor stock levels, lifecycle status, drop-in alternatives from the MC68300 family, and practical design considerations not found in the standalone product brief.

RFQ İletişim
MC68HC000CEI16 - 32-Bit 16MHz M68k MPU, 68-PLCC | NXP / Motorola
MC68HC000CEI16

MC68HC000CEI16 - 32-Bit 16MHz M68k MPU, 68-PLCC | NXP / Motorola

The NXP MC68HC000CEI16 is a 32-bit M68000 family microprocessor (MPU) operating at 16 MHz, housed in a 68-pin Plastic Leaded Chip Carrier (PLCC, 24.21 x 24.21 mm) package. It implements the EC000 low-power variant of the original Motorola 68000 architecture, combining full 32-bit internal data and address paths with a 16-bit external data bus and a 24-bit external address bus to reduce system cost while preserving instruction-set compatibility with the flagship MC68000. The 'CEI' suffix designates the industrial temperature range (typically -40C to +85C), and the '16' suffix denotes the 16 MHz maximum clock. The device supports both 3.3V and 5V supplies and exposes two unidirectional 16-bit data buses, an asynchronous bus interface, and the original M68k programming model with eight 32-bit data registers and eight 32-bit address registers. What is an MPU (Microprocessor Unit)? An MPU is a CPU that requires external program memory, external data memory, and external I/O - in contrast to a microcontroller (MCU), which integrates those resources on-chip. The M68000 (often called 'M68k') family is one of the longest-lived CISC architectures in history: launched in 1979 and still in production today for industrial control, telecom, military/aerospace, and legacy embedded systems where decades of validated assembly code and toolchain investment need to be preserved. The 'HC' suffix (High-speed CMOS) and 'EC' (Enhanced CMOS, lower power) variants dramatically reduced power consumption versus the original NMOS MC68000 while remaining fully pin- and instruction-compatible. Key features of the MC68HC000CEI16 include: a 32-bit programming model with 32-bit operations, byte, word, and long-word addressing; a 16-bit external data bus with dynamic sizing (8/16-bit transfer support); a 24-bit external address bus (16 MB linear address space); seven 32-bit general-purpose data registers (D0-D7) and eight 32-bit address registers (A0-A7, plus a separate user/supervisor stack pointer A7'); supervisor and user operating modes with separate stack pointers; a TRAP, interrupt, and exception model supporting seven interrupt levels (IPL0-IPL2); a 56-bit vector base register for relocation of exception vectors in RAM; and full Bus Arbitration for multi-processor designs. Architecturally, the EC000 implements the M68k instruction set in a more efficient CMOS process and integrates the clock generator on-chip (a small external 25 MHz crystal or TTL clock drives XTAL). The 16 MHz part delivers approximately 2 MIPS of sustained Dhrystone throughput, more than enough to drive legacy peripheral stacks, motion controllers, and protocol bridges. The PLCC-68 package retains the same logical pinout as the original 64-pin DIP MC68000 (with a few package-specific pins routed for the J-leads), enabling drop-in PCB retrofits from legacy 68000 designs into modern surface-mount assemblies. Typical applications include industrial PLC controllers, motion control and CNC sub-systems, telecom protocol converters and modem pools, avionics and military embedded systems (legacy hardware modernization), scientific instruments needing deterministic CPU behaviour, and educational or hobbyist retro-computing boards where authentic M68k behaviour is required. The wide 3.3V/5V supply tolerance allows easy integration into existing 5V M68k backplanes or modernized 3.3V mixed-voltage systems. When designing with this part, note that the PLCC socket requires a 68-pin PLCC socket (not a QFP adapter). Decouple VCC with at least one 0.1 uF ceramic bypass capacitor per supply pin and one bulk 10 uF tantalum or electrolytic cap near the package. Hold RESET low for at least 100 ms after VCC stabilizes to guarantee a clean vector fetch from address $000000 on the first cycle. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in PLCC-68 alternatives from the same M68k family, practical PLCC socket and decoupling design notes, and a parameter comparison table not found in any single manufacturer document.

RFQ İletişim