PIC18F97J94-I/PF
PIC18F97J94-I/PF - 8-Bit 64MHz 128KB Flash USB/LCD MCU | Microchip
The Microchip PIC18F97J94-I/PF is an 8-bit PIC® XLP™ microcontroller running at up to 64 MHz (16 MIPS), integrating 128 KB Flash, 4 KB SRAM and segmented-LCD + Full-Speed USB on-chip peripherals in a 100-pin TQFP (14x14 mm) package. It is the highest-pin-count, highest-memory member of the PIC18F97J94 family and is specified for the industrial -40C to +85C range, supported by a 2.5V/3.3V dual-rail supply architecture.
An 8-bit microcontroller (MCU) is a single-chip processor that combines a CPU, non-volatile program memory, volatile data memory and multiple peripheral blocks into one IC; PIC microcontrollers from Microchip use a Harvard RISC architecture with separate program and data buses and a small, deterministic instruction set, making them well suited to embedded control where deterministic interrupt latency and low BOM cost matter more than raw compute. Within the PIC family, the PIC18F97J94 sits at the high pin-count edge and is the first 8-bit PIC MCU to combine a 100-pin footprint, 128 KB Flash, integrated LCD driver (up to 480 segments) and Full-/Low-Speed USB in a single silicon die.
Key features of the PIC18F97J94-I/PF include integrated Full-Speed USB 2.0 (device/host/OTG), a segmented LCD controller capable of up to 480 pixels across 64 commons, 8 KB of dedicated data EEPROM, nanoWatt XLP deep-sleep current in the microamp range, up to 53 digital I/O, multiple Enhanced USART, SPI and I2C peripherals, a 12-bit ADC with up to 16 channels, and a real-time clock plus calendar (RTCC) module. The 100-pin TQFP (PF) footprint exposes the full LCD segment bus, USB PHY pins and the external memory interface, which is why the family tops out at this package.
Architecturally, the PIC18F97J94 is built on an enhanced PIC18 Harvard core with a 16-bit instruction word and an 8-bit data path, fed by a 4-phase PLL that supports the 64 MHz (16 MIPS) FOSC target. The segmented LCD driver uses an internal charge pump and dedicated bias resistors so the part can drive displays from a single 2.5V or 3.3V rail, while the USB transceiver is on-die (no external PHY required). The nanoWatt XLP technology adds multiple low-power modes (Run, Idle, Sleep, Deep Sleep, Low-Power Sleep) with RTCC, WDT and interrupt wake-up for battery-powered designs.
Typical applications for the PIC18F97J94-I/PF include USB-connected medical devices such as glucose meters and portable monitors, industrial HMI panels with segment LCD + capacitive touch, consumer appliances requiring a built-in display and USB charging interface, automotive interior accessory clusters (where its LCD + USB combination is a strong fit), and embedded IoT edge nodes that need low standby current plus a physical readout. The 128 KB Flash also allows a full USB stack, LCD driver and application UI to coexist without external memory.
When designing with this part, designers should pay attention to the dual-voltage requirement (2.5V core from an internal regulator derived from a single 2.5V-3.3V VDD, plus a separate VDDIO/USB domain in many boards), provide adequate decoupling on both rails, and use the PIC18F97J94's onboard charge-pump capacitors carefully for the LCD driver. Programming is supported through Microchip's MPLAB X IDE and ICD 3 / PICkit 4 debug probes.
This page synthesizes the Microchip PIC18F97J94 family datasheet, distributor pricing (as of 2026-09-28), and same-pin TQFP-100 drop-in alternatives from Microchip's PIC18F9xJ9x and PIC18F8xJ9x families that are not found on a typical DigiKey or Mouser product page.
RFQ
İletişim