Mikrodenetleyiciler

Ürünler (20.000+)

ATTINY88-MMU - 12MHz 8KB AVR MCU, 28-VQFN | Microchip
ATTINY88-MMU

ATTINY88-MMU - 12MHz 8KB AVR MCU, 28-VQFN | Microchip

Microchip Technology ATTINY88-MMU is an 8-bit AVR RISC microcontroller with 12 MHz maximum clock speed, 8 KB of in-system programmable flash memory, 64 bytes of EEPROM, 512 bytes of SRAM, and 28 general-purpose I/O lines in a 28-VQFN 4x4 mm package. The device operates from 1.8 V to 5.5 V and is presented in a tray package by Arrow Electronics. An AVR microcontroller is a compact embedded-processing semiconductor that combines a CPU core, program memory, data memory, and peripherals on one integrated circuit. The ATTINY88 belongs to the AVR 8-bit product hierarchy, where it functions as a general-purpose microcontroller suitable for embedded control, sensing, and low-power automation. Its picoPower AVR architecture targets efficient instruction execution and energy-conscious embedded operation. Key features include 8 KB of ISP flash organized as 4K x 16, 64 bytes of EEPROM, 512 bytes of SRAM, and 28 general-purpose I/O lines. The device provides two flexible timer/counters with compare modes and supports internal and external clock sources. In-system programming and in-circuit debugging facilitate programming and troubleshooting, while the 1.8 V to 5.5 V supply range allows use with common low-voltage and legacy 5 V systems. The ATTINY88 combines a high pin count with relatively small memory resources. This balance supports multi-I/O control boards, compact sensor nodes, and embedded products that need more GPIO than an 8-pin or 14-pin MCU but do not require the memory or processing capacity of a 32-bit microcontroller. Its 28-VQFN footprint also reduces board area, although the fine-pitch package demands careful PCB layout and assembly. Typical applications include industrial control modules, environmental monitoring, LED and lighting controllers, compact sensor hubs, appliance interfaces, and low-power embedded products. The 28 GPIO lines allow multiple inputs and outputs to be connected simultaneously, reducing the need for external I/O expanders in small systems. Designers should pay close attention to the 4x4 mm VQFN exposed-pad land pattern, pin orientation, and the availability of only 512 bytes of SRAM. Firmware should avoid unnecessary RAM buffering, use EEPROM only for data that must persist across power cycles, and include the exposed thermal pad in the PCB copper and assembly process. This page consolidates verified manufacturer and distributor information, a parameter-by-parameter comparison, application guidance, and practical design notes for engineers evaluating the ATTINY88-MMU, its package constraints, and verified same-family alternatives.

RFQ İletişim
ATTINY88-MU 12MHz 8KB 32-VQFN AVR MCU | Microchip
ATTINY88-MU

ATTINY88-MU 12MHz 8KB 32-VQFN AVR MCU | Microchip

Microchip Technology ATTINY88-MU is an 8-bit AVR RISC-based CMOS microcontroller with an operating frequency of 12MHz, 8KB of in-system-programmable flash memory and 28 general-purpose I/O lines in a 32-VQFN package measuring 5mm by 5mm. It operates from 1.8V to 5.5V and provides 512 bytes of SRAM, 64 bytes of EEPROM, two timer/counters, a 10-bit ADC, SPI and debugWire support. An AVR microcontroller is an 8-bit embedded-control semiconductor that combines a processor core, nonvolatile program memory, data memory and peripherals on one integrated circuit. Within the product hierarchy, ATTINY88-MU belongs to the ATtiny family of compact microcontrollers. Its 28 I/O pins provide substantial connectivity for sensors, switches, indicators, actuators and small serial interfaces while maintaining a low component count. Key verified features include up to 12MIPS throughput at 12MHz, eight 8-bit timer/counter registers, programmable watchdog operation and support for In-Circuit Serial Programming. The device combines a 10-bit ADC, SPI serial interface and debugWire debugging in a 5mm-square surface-mount package. These resources suit compact control systems requiring mixed digital and analog input without a larger microcontroller package. The ATtiny48/88 family uses Microchip picoPower AVR architecture to balance processing capability with low-power operation. Because ATTINY88-MU is an 8-bit device, firmware is best organized around interrupt-driven control, timers, digital state machines and periodic sensor sampling. The 512-byte SRAM should be budgeted carefully when buffering data or supporting multiple communication routines, while the 8KB flash capacity favors compact code and bootloading strategies. Typical applications include small industrial controllers, building automation endpoints, sensor hubs, LED-control systems, appliance interfaces and compact embedded instruments. A designer can use the 28 GPIO pins for local controls while assigning SPI to an external sensor or display and using the ADC for analog measurement. Programming is supported through the device's programming and debug interfaces documented by Microchip. A critical PCB consideration is exposed-pad and via layout in the 32-VQFN package. Confirm the exact land pattern, pad dimensions and pin mapping against the manufacturer package drawing before fabrication. Keep analog and digital return paths controlled, provide local supply decoupling, and use the reset and programming interface so programming and debugging remain accessible in production. This page consolidates verified distributor specifications, lifecycle information, application guidance and practical package considerations. It distinguishes verified ATTINY88-MU facts from parameters unavailable in the supplied search results, avoiding unsupported electrical or lifecycle assumptions while helping engineers assess fit before requesting a quote.

RFQ İletişim
ATTINY88-MUR 12MHz 8KB 32-VQFN AVR MCU | Microchip (Tape & Reel)
ATTINY88-MUR

ATTINY88-MUR 12MHz 8KB 32-VQFN AVR MCU | Microchip (Tape & Reel)

Microchip Technology ATTINY88-MUR is an 8-bit AVR RISC-based CMOS microcontroller with an operating frequency of 12MHz, 8KB of in-system-programmable flash memory and 28 general-purpose I/O lines in a 32-VQFN package measuring 5mm by 5mm. It operates from 1.8V to 5.5V and provides 512 bytes of SRAM, 64 bytes of EEPROM, two timer/counters, a 10-bit ADC, SPI and debugWire support. An AVR microcontroller is an 8-bit embedded-control semiconductor that combines a processor core, nonvolatile program memory, data memory and peripherals on one integrated circuit. Within the product hierarchy, ATTINY88-MUR belongs to the ATtiny family of compact microcontrollers. Its 28 I/O pins provide substantial connectivity for sensors, switches, indicators, actuators and small serial interfaces while maintaining a low component count. Key verified features include up to 12MIPS throughput at 12MHz, eight 8-bit timer/counter registers, programmable watchdog operation and support for In-Circuit Serial Programming. The device combines a 10-bit ADC, SPI serial interface and debugWire debugging in a 5mm-square surface-mount package. These resources suit compact control systems requiring mixed digital and analog input without a larger microcontroller package. The ATtiny48/88 family uses Microchip picoPower AVR architecture to balance processing capability with low-power operation. Because ATTINY88-MUR is an 8-bit device, firmware is best organized around interrupt-driven control, timers, digital state machines and periodic sensor sampling. The 512-byte SRAM should be budgeted carefully when buffering data or supporting multiple communication routines, while the 8KB flash capacity favors compact code and bootloading strategies. Typical applications include small industrial controllers, building automation endpoints, sensor hubs, LED-control systems, appliance interfaces and compact embedded instruments. A designer can use the 28 GPIO pins for local controls while assigning SPI to an external sensor or display and using the ADC for analog measurement. Programming is supported through the device's programming and debug interfaces documented by Microchip. A critical PCB consideration is exposed-pad and via layout in the 32-VQFN package. Confirm the exact land pattern, pad dimensions and pin mapping against the manufacturer package drawing before fabrication. Keep analog and digital return paths controlled, provide local supply decoupling, and use the reset and programming interface so programming and debugging remain accessible in production. This page consolidates verified distributor specifications, lifecycle information, application guidance and practical package considerations. It distinguishes verified ATTINY88-MUR facts from parameters unavailable in the supplied search results, avoiding unsupported electrical or lifecycle assumptions while helping engineers assess fit before requesting a quote.

RFQ İletişim
ATTINY88-PU - 8-Bit 12MHz AVR MCU | Microchip Technology
ATTINY88-PU

ATTINY88-PU - 8-Bit 12MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY88-PU is an 8-bit AVR ATtiny microcontroller with 8KB of in-system programmable flash memory, a 12 MHz maximum clock, and a 28-PDIP package. It operates across the verified 1.8V to 5.5V supply range and is intended for compact embedded-control, sensing, and actuator designs. The ATTINY88-PU also provides 64 bytes of EEPROM and 512 bytes of SRAM according to the cited comparison data, giving firmware designers more working memory than the smallest ATtiny devices while retaining a small through-hole footprint. A microcontroller is a semiconductor that integrates a processor core, nonvolatile program memory, data memory, and peripherals into one device. The ATtiny88 belongs to the 8-bit AVR family, a low-complexity controller family suited to real-time control loops, digital I/O, timers, communication interfaces, and small sensor systems. The ATTINY88-PU uses an advanced RISC architecture and is supported by an ecosystem of AVR-compatible tools and libraries. The verified feature set includes 8KB of in-system programmable flash, 64 bytes of EEPROM, 512 bytes of SRAM, 123 powerful instructions, and a 12MHz operating speed. Its 1.8V to 5.5V range supports both low-voltage and conventional 5V designs. The 28-PDIP package is useful for prototypes, through-hole assembly, hand wiring, and designs where a socket or easy rework is useful. Typical embedded uses include environmental monitoring, small motor or relay control, LED status systems, keypad interfaces, and compact control boards. Because the exact pin names, timers, peripherals, electrical limits, and package drawing are not supplied in the verified data, those details should be confirmed in the manufacturer datasheet before schematic capture or firmware deployment. Design with the DIP footprint, clock source, programming interface, decoupling requirements, and I/O voltage limits verified against the official datasheet. The 12 MHz operating speed does not by itself guarantee a particular timer frequency; the actual peripheral clock behavior depends on the selected clock source, fuse configuration, and divider settings. This page combines verified manufacturer and distributor facts with purchasing context, application guidance, and conservative replacement qualification. It does not claim a drop-in alternative unless the same package and pin-level compatibility are explicitly supported by available cross-reference data.

RFQ İletişim
ATTINY9-MAH - 8-Bit 12MHz AVR with 1KB Flash | Microchip
ATTINY9-MAH

ATTINY9-MAH - 8-Bit 12MHz AVR with 1KB Flash | Microchip

The Microchip Technology ATTINY9-MAH is an 8-bit AVR RISC-based microcontroller operating up to 12 MHz, with 1 KB of ISP Flash memory, 32 bytes of SRAM, and four general-purpose I/O lines. It is packaged in an 8-UFDFN exposed-pad package for compact, surface-mount embedded designs. The verified distributor data identifies the part as an ATtiny-series AVR device using an internal oscillator and supplied in bulk packaging. A microcontroller is a programmable integrated circuit that executes firmware to monitor inputs, control outputs, and manage system timing. In the broader semiconductor hierarchy, this device is an 8-bit microcontroller, part of the AVR family, and belongs to the embedded-control and power-management design ecosystem. The ATTINY9 is positioned for small control tasks where low memory capacity, low pin count, and simple timing are more important than a large peripheral set or high processing bandwidth. Verified specifications include 1 KB of program Flash, 32 bytes of SRAM, four I/O lines, a 12 MHz maximum speed, an internal oscillator, and a 16-bit timer/counter with two PWM channels. The manufacturer page also identifies 16 general-purpose working registers and power-on reset, PWM, and watchdog-related functionality. These resources support compact control loops, simple indicator systems, basic motor or actuator timing, and low-power embedded products. The 8-UFDFN package helps reduce board area compared with larger leaded or plastic packages, but its exposed pad and fine-pitch footprint require careful PCB layout, land-pattern verification, soldering controls, and thermal-via planning. Because the provided data does not specify the complete electrical operating range, pin names, memory-retention behavior, or detailed timing characteristics, those parameters are marked as needing verification rather than inferred. Typical uses include small sensor interfaces, simple timers, compact LED or indicator controllers, low-cost consumer accessories, and basic embedded control modules. The device is most appropriate when firmware and I/O requirements are modest and the board can be designed around its 1 KB Flash and 32-byte SRAM limits. For designs needing more memory, communication peripherals, or a larger package pin count, a different ATtiny device should be evaluated. For a new design, confirm the exact UFDFN footprint, exposed-pad connection, programming method, oscillator behavior, and device-specific electrical limits against the official Microchip documentation before layout release. This page combines verified distributor specifications with engineering guidance, while clearly separating confirmed data from parameters that require manufacturer-datasheet confirmation.

RFQ İletişim
ATTINY9-MAHR - 8-Bit 12MHz AVR with 1KB Flash | Microchip (Tape & Reel)
ATTINY9-MAHR

ATTINY9-MAHR - 8-Bit 12MHz AVR with 1KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATTINY9-MAHR is an 8-bit AVR RISC-based microcontroller operating up to 12 MHz, with 1 KB of ISP Flash memory, 32 bytes of SRAM, and four general-purpose I/O lines. It is packaged in an 8-UFDFN exposed-pad package for compact, surface-mount embedded designs. The verified distributor data identifies the part as an ATtiny-series AVR device using an internal oscillator and supplied in bulk packaging. A microcontroller is a programmable integrated circuit that executes firmware to monitor inputs, control outputs, and manage system timing. In the broader semiconductor hierarchy, this device is an 8-bit microcontroller, part of the AVR family, and belongs to the embedded-control and power-management design ecosystem. The ATTINY9 is positioned for small control tasks where low memory capacity, low pin count, and simple timing are more important than a large peripheral set or high processing bandwidth. Verified specifications include 1 KB of program Flash, 32 bytes of SRAM, four I/O lines, a 12 MHz maximum speed, an internal oscillator, and a 16-bit timer/counter with two PWM channels. The manufacturer page also identifies 16 general-purpose working registers and power-on reset, PWM, and watchdog-related functionality. These resources support compact control loops, simple indicator systems, basic motor or actuator timing, and low-power embedded products. The 8-UFDFN package helps reduce board area compared with larger leaded or plastic packages, but its exposed pad and fine-pitch footprint require careful PCB layout, land-pattern verification, soldering controls, and thermal-via planning. Because the provided data does not specify the complete electrical operating range, pin names, memory-retention behavior, or detailed timing characteristics, those parameters are marked as needing verification rather than inferred. Typical uses include small sensor interfaces, simple timers, compact LED or indicator controllers, low-cost consumer accessories, and basic embedded control modules. The device is most appropriate when firmware and I/O requirements are modest and the board can be designed around its 1 KB Flash and 32-byte SRAM limits. For designs needing more memory, communication peripherals, or a larger package pin count, a different ATtiny device should be evaluated. For a new design, confirm the exact UFDFN footprint, exposed-pad connection, programming method, oscillator behavior, and device-specific electrical limits against the official Microchip documentation before layout release. This page combines verified distributor specifications with engineering guidance, while clearly separating confirmed data from parameters that require manufacturer-datasheet confirmation.

RFQ İletişim
ATTINY9-TS8R - 8-Bit 10MHz AVR MCU | Microchip Technology
ATTINY9-TS8R

ATTINY9-TS8R - 8-Bit 10MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY9-TS8R is an 8-bit AVR RISC microcontroller with 1 KB of ISP Flash memory, 32 bytes of SRAM, four general-purpose I/O lines, and a maximum clock speed of 10 MHz, supplied in a 6-pin SOT-23 package. It operates from 2.5 V to 5.5 V, making it suitable for compact embedded-control and low-power consumer designs. An 8-bit microcontroller is a compact computing device that executes embedded instructions from nonvolatile program memory and interfaces with sensors, switches, indicators, and other peripherals. The ATTINY9 belongs to Microchip's ATtiny family, which combines an AVR processor core, timer functions, GPIO resources, and internal oscillators in a small surface-mount package. Its 16 general-purpose working registers support efficient single-cycle instruction execution. The ATTINY9-TS8R provides 1 KB of program memory organized as 512 words by 16 bits, 32 bytes of SRAM, and four I/O pins. Its 16-bit timer/counter includes two PWM channels, while its internal oscillator eliminates the need for an external clock in suitable designs. The device also supports power-on reset and watchdog-related functionality described for the ATtiny9 family. The device combines an 8-bit AVR core with only 1 KB of Flash, making code size the principal design constraint. Its 32-byte SRAM is sufficient for compact state machines, simple control loops, and low-data-volume serial or GPIO tasks, but it is not intended for large buffers or complex host-side connectivity. The 10 MHz operating speed balances responsiveness against clock power and execution time. Typical uses include compact household appliances, simple sensor interfaces, lighting controls, push-button products, low-power timers, and auxiliary controllers. In each case, the ATTINY9 is appropriate when the firmware can fit within 1 KB and the design needs only a small number of digital control points rather than a high-pin-count MCU or application processor. Designers should verify the exact pin assignments, oscillator options, fuse settings, and programming interface against the Microchip ATtiny9 documentation before layout. Decoupling, programming-test access, reset behavior, and exposed-pad-free SOT-23-6 assembly also need to be addressed. The very small package can complicate hand rework and automated optical inspection during prototype builds. This product page consolidates verified manufacturer and distributor information, package details, sourcing links, practical design guidance, and same-package alternatives. The comparison and selection notes distinguish confirmed drop-in candidates from parts that may require firmware or hardware changes, helping engineers choose a replacement without relying on package name alone.

RFQ İletişim
ATTINY9-TSHR - 12MHz 1KB AVR Microcontroller | Microchip Technology
ATTINY9-TSHR

ATTINY9-TSHR - 12MHz 1KB AVR Microcontroller | Microchip Technology

Microchip Technology ATTINY9-TSHR is an 8-bit AVR RISC-based microcontroller with 1 KB of ISP Flash memory, 32 bytes of SRAM, four general-purpose I/O lines, and a maximum clock speed of 12 MHz, packaged in a 6-pin SOT-23-6 surface-mount package. It is designed for compact embedded-control designs that require low-power operation, modest program memory, and integrated timing and conversion resources. A microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, working RAM, input/output ports, and embedded peripherals on one device. The ATtiny9 belongs to the ATtiny family of AVR microcontrollers, a low-power RISC architecture commonly used for simple sensing, control, and signal-generation tasks. Its compact package and limited resource footprint make it suitable for space-constrained products rather than connectivity-heavy or high-compute systems. The ATTINY9-TSHR provides 1 KB of ISP Flash memory, 32 bytes of SRAM, four general-purpose I/O lines, 16 general-purpose working registers, and a 16-bit timer/counter with two PWM channels. It also includes an internal oscillator, an analog-to-digital converter, a watchdog-related feature set, and an ISP programming interface. The 12 MHz maximum speed provides useful timing headroom for basic control loops, while the four I/O pins constrain designs to signals that fit the small package. Typical applications include simple sensor nodes, LED and light-control modules, compact motor or actuator controllers, battery-powered accessories, and small embedded products that require local logic rather than a high-performance processor. The ATtiny9 family is also associated with low-power and cost-sensitive embedded systems in which deterministic timing, simple control, and compact PCB area matter more than large memory capacity or extensive communications. The principal design trade-off is resource limitation. Four I/O pins leave little room for multiple sensors, displays, or communications peripherals, and 1 KB of Flash requires compact firmware with careful attention to library size. Use the manufacturer pin-description table when assigning tracks, and confirm that the selected ISP programming and clocking arrangement satisfies the product's startup and update requirements. This page combines the verified ATTINY9-TSHR specifications, package information, application guidance, cross-reference alternatives, and practical design notes to help engineers evaluate this AVR microcontroller before layout and firmware development begin.

RFQ İletişim
ATXMEGA128A1-AU - 8/16-bit AVR XMEGA MCU, 128KB Flash, TQFP-100
ATXMEGA128A1-AU

ATXMEGA128A1-AU - 8/16-bit AVR XMEGA MCU, 128KB Flash, TQFP-100

The Microchip Technology ATXMEGA128A1-AU is a low-power, high-performance 8/16-bit AVR XMEGA A1 microcontroller based on the AVR enhanced RISC architecture, delivering 32 MHz CPU throughput with single-cycle instruction execution and 128 KB of in-system self-programming Flash, 8 KB SRAM, 2 KB EEPROM, and 8 KB boot code section in a 100-pin TQFP (14x14 mm) package. What is an XMEGA microcontroller? The XMEGA family represents Atmel/Microchip's high-performance 8/16-bit AVR RISC architecture, sitting in the taxonomy: microcontroller -> embedded MCU -> 8/16-bit RISC MCU -> AVR XMEGA family -> A1 series. XMEGA devices execute most instructions in a single clock cycle, achieving throughput approaching 1 MIPS per MHz, and integrate rich peripherals such as DMA controllers, event systems, and multi-level interrupt controllers to reduce CPU load in real-time applications. Key features of the ATXMEGA128A1-AU include four-channel DMA controller, eight-channel event system, programmable multi-level interrupt controller, 78 general-purpose I/O lines, 16-bit real-time counter (RTC), eight flexible 16-bit timer/counters with compare and PWM channels, eight USARTs, four SPI/serial interfaces, two I2C/TWI interfaces, 12-bit ADC and DAC, and a full-speed USB device interface. The wide 1.6 V to 3.6 V operating voltage range supports both 1.8 V and 3.3 V system designs. The ATXMEGA128A1-AU uses a pipelined Harvard architecture with 32 working registers directly connected to the ALU, enabling high code density and deterministic interrupt latency. The peripheral event system allows peripherals to communicate without CPU intervention, while the four-channel DMA controller offloads data movement between memory and peripherals, ideal for high-throughput sensor aggregation or USB transfers. Typical applications include industrial control systems, building automation, smart energy metering, motor control, USB human-interface devices, sensor hubs, and low-power wireless sensor nodes. Its high peripheral integration and rich connectivity make it well-suited for designs consolidating multiple discrete functions onto a single MCU. When designing with this device, note that the A1 family is marked Not Recommended for New Designs by Microchip, with the AU series offered as the preferred successor. Designers should validate long-term availability before committing to new production. Decoupling with 100 nF ceramic capacitors near each supply pin is essential for clean ADC and DAC performance. This page synthesizes distributor pricing, lifecycle status, drop-in alternative recommendations, and practical design notes that complement the manufacturer datasheet, enabling engineers to make informed sourcing and design decisions.

RFQ İletişim
ATXMEGA128A1-CU - 128KB Flash 32MHz XMEGA A1 MCU 100-CBGA
ATXMEGA128A1-CU

ATXMEGA128A1-CU - 128KB Flash 32MHz XMEGA A1 MCU 100-CBGA

The Microchip (Atmel) ATXMEGA128A1-CU is a low-power, high-performance 8/16-bit AVR XMEGA A1 microcontroller featuring 128 KB of self-programming Flash program memory, 8 KB SRAM, 2 KB EEPROM, and a 100-ball CBGA (9x9 mm) package. Operating from 1.6 V to 3.6 V with a 32 MHz core clock, it executes instructions in a single cycle, approaching 1 MIPS per MHz, while the integrated DMA controller and 8-channel event system offload the CPU for deterministic peripheral handling. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), working memory (SRAM), non-volatile data storage (EEPROM), and programmable peripherals. Within the broader taxonomy, an MCU belongs to the category of embedded processors, sitting below microprocessors in system hierarchy and above discrete logic ICs in functional capability. The AVR XMEGA family specifically represents an 8/16-bit RISC architecture that targets low-power, deterministic, real-time embedded applications, balancing DSP-class peripheral integration with simple C-friendly tooling. Key features of the ATXMEGA128A1-CU include 78 general-purpose I/O lines, eight 16-bit timer/counters with PWM and capture, a 16-bit RTC, four-channel DMA, programmable multi-level interrupt controller, USB full-speed device support via on-chip transceiver, multiple USART/SPI/TWI interfaces, an external bus interface, a 12-bit ADC and 12-bit DAC, AES and DES crypto accelerators, and an on-chip debug (OCD) system with PDI/DebugWIRE support. The 100-CBGA (9x9 mm, 0.8 mm pitch) package provides generous I/O and an exposed thermal structure suitable for industrial temperature ranges. Architecturally, the device pairs an enhanced AVR RISC pipeline with Harvard-style busing and a peripheral event system that lets peripherals signal one another without CPU intervention - a hallmark of XMEGA's deterministic real-time design. The 1.6 V to 3.6 V wide operating range, multiple sleep modes, and on-chip voltage regulator make it well suited to battery-powered and industrial sensor nodes. Note that the ATXMEGA128A1 family is marked Not Recommended for New Designs (NRND) by Microchip in favor of the newer XMEGA AU series. Typical applications include industrial control (HVAC, factory automation, motor drive controllers, building systems), hand-held battery-powered instrumentation, power tools, smart metering, optical and medical devices, large home appliances, and USB peripherals. Its crypto engines also make it a fit for embedded security nodes. When designing with this part, allocate the 8 KB SRAM and 2 KB EEPROM budgets carefully and reserve at least 4 KB of the 128 KB Flash for a robust bootloader. The 100-CBGA package requires careful PCB pad design and reflow profiling; verify the 0.8 mm pitch footprint against Microchip's package drawing before fab release. This page synthesizes distributor availability, same-package drop-in alternatives from the XMEGA family, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
ATXMEGA128A1-CUR - 128KB Flash 32MHz AVR XMEGA MCU | Microchip
ATXMEGA128A1-CUR

ATXMEGA128A1-CUR - 128KB Flash 32MHz AVR XMEGA MCU | Microchip

The Microchip ATXMEGA128A1-CUR is a low-power, high-performance 8/16-bit AVR XMEGA microcontroller delivering 32 MIPS throughput at 32 MHz, packaged in a 100-ball 9x9 mm TFBGA (CBGA) for compact embedded designs. According to the Microchip (formerly Atmel) datasheet, the device integrates 128 KB of in-system self-programming Flash with read-while-write support, 8 KB boot code section, 8 KB SRAM, 2 KB EEPROM, a four-channel DMA controller, an eight-channel event system, and a programmable multilevel interrupt controller. Operating voltage spans 1.6 V to 3.6 V across an industrial temperature range of -40°C to +85°C, making it suitable for battery-powered and industrial-grade applications. An AVR XMEGA microcontroller is a member of the 8/16-bit RISC microcontroller family based on the enhanced AVR architecture. Within the broader taxonomy, XMEGA devices sit between classic 8-bit AVR MCUs and 32-bit ARM Cortex-M parts - they execute most instructions in a single clock cycle, achieving 1 MIPS per MHz, while exposing richer peripherals (DMA, event system, AES/DES crypto on some variants) than legacy ATmega devices. The XMEGA A1 family is the top-of-line 100-pin tier, with the highest pin count, largest memory options, and the most peripheral channels in the XMEGA lineup. Key features of the ATXMEGA128A1-CUR include four USARTs, four TWI (I²C-compatible) interfaces, two SPI ports, a 12-channel 16-bit event system, an 8-channel 16-bit timer/counter array with PWM and compare modes, a 12-bit 2 Msps ADC, two 12-bit DACs, an analog comparator with hysteresis, and 78 general-purpose I/O lines. The 100-ball TFBGA package provides a 0.8 mm ball pitch and 1.2 mm height, optimized for compact handheld and IoT designs. Compared to ATmega128, the XMEGA core delivers roughly 2-4x the MIPS at the same clock while adding DMA and event-driven peripherals. Typical applications include industrial sensor hubs, building automation controllers, USB human-interface devices, smart energy metering nodes, low-power wireless sensor platforms, and motor-control signal processors. Designers select this part when they need AVR toolchain compatibility (AVR Studio, Microchip Studio, GCC-AVR) combined with XMEGA's DMA and event system for deterministic, low-CPU-overhead peripheral handling. When designing with this device, place the 100-ball TFBGA land pattern on a minimum 4-layer PCB with continuous ground planes beneath the package to ensure stable JTAG/PDI programming and to manage thermal dissipation at high MIPS loads. Always include decoupling: a 100 nF ceramic capacitor per VCC pin pair plus a bulk 4.7 µF tantalum or ceramic near the supply rail. Microchip recommends Atmel-ICE or AVR Dragon for PDI programming. This page synthesizes distributor pricing, drop-in AVR XMEGA alternatives, package-level pinout, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim
ATXMEGA128A4U-AUR - 8/16-bit AVR XMEGA MCU, 128KB Flash, 44-TQFP | Microchip
ATXMEGA128A4U-AUR

ATXMEGA128A4U-AUR - 8/16-bit AVR XMEGA MCU, 128KB Flash, 44-TQFP | Microchip

The Microchip ATXMEGA128A4U-AUR is an 8/16-bit AVR XMEGA A4U microcontroller featuring 128 KB of in-system self-programmable Flash, 8 KB SRAM, 2 KB EEPROM, and a 4 KB boot code section, all packaged in a 44-pin TQFP (10x10 mm) supplied on tape and reel. It operates at up to 32 MHz delivering up to 32 MIPS throughput, integrates a 4-channel DMA controller, an 8-channel event system, and a full-speed USB 2.0 device/host interface that distinguishes the A4U family from earlier A4 devices. The part number suffix "-AUR" indicates the industrial temperature grade and tape-and-reel packaging for high-volume assembly. An AVR XMEGA microcontroller is a high-performance 8/16-bit RISC MCU family from Microchip (originally Atmel) targeting low-power embedded designs that need more peripherals than classic ATmega parts but still rely on the AVR core rather than ARM Cortex-M. Within the broader taxonomy it sits as an MCU -> microcontroller -> embedded controller -> semiconductor. The "XMEGA" name signals an upgraded peripheral set including hardware crypto, DES, AES, and 12-bit ADC/DAC blocks, plus the unified event system for inter-peripheral signalling without CPU intervention. Key differentiating specifications include the 128 KB Flash (64K x 16 organization), 8 KB SRAM, 2 KB EEPROM, 12-bit ADC and DAC peripherals, full-speed USB 2.0 with device and host capability, and an operating voltage range of 1.6 V to 3.6 V. The device supports both 1.8 V and 2.5 V/3.3 V operation, allowing direct attachment to Li-ion, NiMH, or 3.3 V regulated rails without level shifters. An external bus interface provides address/data expansion for external memories or graphics controllers. Architecturally, the ATXMEGA128A4U-AUR uses the Atmel AVR enhanced RISC core with 32 working registers directly connected to the ALU, achieving single-cycle execution. The integrated DMA controller can move data between peripherals and memory without CPU involvement, freeing the core for application code. The 8-channel event system routes peripheral events (timer overflows, ADC conversions, I/O edges) to other peripherals, enabling deterministic hardware-software co-design. The USB 2.0 full-speed transceiver is on-die, requiring only an external pull-up resistor and bypass capacitors. Typical applications include USB HID devices, USB mass storage controllers, industrial sensor hubs with USB diagnostics, low-power data loggers, motor control front ends, and battery-powered handheld instruments. The combination of low active current, deep sleep modes down to sub-microamp, and integrated USB makes it particularly attractive for USB-powered sensor peripherals. Designers also use the A4U family in consumer audio accessories where 12-bit DAC and PWM drive suit headphone or intercom front ends. When designing with this part, budget for the 44-pin TQFP footprint and ensure the USB D+/D- traces are 90 ohm differential-matched. Boot loader and PDI programming share the same pins, so reserve access for in-system programming via the Atmel-ICE or AVR Dragon. The integrated 32 kHz internal RC oscillator can replace an external crystal in space-constrained designs but trades accuracy for BOM savings. This page synthesizes distributor pricing, USB-enabled drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim
ATXMEGA128B3-MCU - 32MHz AVR MCU, 128KB Flash, USB | Microchip
ATXMEGA128B3-MCU

ATXMEGA128B3-MCU - 32MHz AVR MCU, 128KB Flash, USB | Microchip

The Microchip Technology ATXMEGA128B3-MCU is a low-power, high-performance 8/16-bit AVR XMEGA B3 microcontroller with 128KB self-programming Flash, 4KB SRAM, 2KB EEPROM, a 2-channel DMA controller, 4-channel event system, Full-Speed USB Device, 4x25-segment LCD controller, and up to 32 MIPS throughput at 32 MHz, housed in a 64-pin VQFN (7x7 mm) package with exposed pad. A microcontroller unit (MCU) is a single-chip computer integrating a processor core, program and data memory, and peripherals into one package. Within the hierarchy of embedded processors, the AVR XMEGA family sits between small 8-bit AVRs and 32-bit ARM cores, offering 8/16-bit RISC execution with the peripheral richness needed for human-interface and connectivity applications. Key features include 128KB (128K x 8) of self-programming Flash with a 4KB boot code section, enabling field firmware updates over USB or other interfaces; a 4-channel event system that routes peripheral signals without CPU intervention; and a 2-channel DMA controller that offloads data movement for lower CPU load and power consumption. Technically, the AVR RISC core executes most instructions in a single clock cycle, delivering up to 32 MIPS at 32 MHz. The integrated USB Full-Speed Device controller eliminates an external USB interface chip, while the 4x25 segment LCD driver with selectable drive schemes suits battery-powered metering and display products. Typical applications include USB-connected instruments, industrial control panels with LCD displays, battery-powered metering devices, and consumer appliances requiring both USB and segment LCD interfaces. When designing with this device, budget the VQFN-64 exposed-pad footprint for thermal and ground via connections, and verify Flash endurance and supply-voltage ranges against the manufacturer datasheet before finalizing power sequencing. This page synthesizes distributor pricing from LCSC and Heisener, drop-in same-family alternatives, and practical design guidance not found in the manufacturer datasheet alone.

RFQ İletişim
ATXMEGA128D4-AU - 128KB Flash XMEGA AVR MCU 32MHz 44TQFP | Microchip
ATXMEGA128D4-AU

ATXMEGA128D4-AU - 128KB Flash XMEGA AVR MCU 32MHz 44TQFP | Microchip

The Microchip (Atmel) ATXMEGA128D4-AU is a high-performance, low-power 8/16-bit AVR XMEGA microcontroller integrating 128 KB of in-system programmable Flash with read-while-write support, 2 KB EEPROM, and 8 KB SRAM, housed in a 44-pin TQFP package. It executes instructions at up to 32 MHz from a 1.6-3.6 V supply, with 34 general-purpose I/O lines, two USARTs, two TWI (I2C) interfaces, four flexible 16-bit timer/counters with compare and PWM channels, a 16-bit real-time counter, a four-channel event system, and a programmable multi-level interrupt controller. An 8 KB boot-code section is dedicated for bootloader use, and the device supports AES and DES crypto accelerators plus a 12-bit, 2 MSPS ADC. An 8/16-bit AVR XMEGA microcontroller is an advanced member of Microchip's AVR family combining 8-bit code density with 16-bit peripheral datapaths. It belongs to the broader class of microcontrollers (MCUs) within embedded processors and semiconductors, designed for deterministic real-time control with very low active and sleep-mode power. The XMEGA D4 sub-family specifically targets low-power mixed-signal applications requiring moderate pin counts and rich peripheral integration, sitting above tinyAVR and megaAVR in the Atmel/Microchip MCU hierarchy. Key features include the four-channel event system for inter-peripheral signalling without CPU intervention, a programmable multi-level interrupt controller for deterministic response, a 12-bit 2 MSPS ADC with optional gain stage, and a hardware AES/DES cryptographic engine. The 8 KB boot section allows secure bootloader updates, while the read-while-write Flash enables live firmware upgrades without halting execution. Power-saving features include five sleep modes, a 1.5 µA real-time-counter backup mode, and a peripheral event system that can wake the CPU autonomously. Typical applications include industrial control panels, sensor hubs, low-power wireless sensor nodes, motor control, smart metering, USB device peripherals, consumer white goods, and human-machine interface (HMI) touch panels. The wide 1.6-3.6 V operating range and integrated peripherals make it well suited to battery-powered and energy-harvesting designs. Designers should provide a 0.1 µF decoupling capacitor adjacent to each VCC pin, route analog and digital grounds separately, and observe the 32 MHz maximum system clock. For firmware development, Microchip's Atmel Studio 7 and MPLAB X IDE with the AVR/GNU toolchain target this device directly.

RFQ İletişim
ATXMEGA128D4-MH - 32MHz AVR XMEGA D4 MCU 128KB Flash | Microchip
ATXMEGA128D4-MH

ATXMEGA128D4-MH - 32MHz AVR XMEGA D4 MCU 128KB Flash | Microchip

The Microchip (formerly Atmel) ATXMEGA128D4-MH is a high-performance, low-power 8/16-bit AVR XMEGA D4 microcontroller combining 128 KB ISP Flash memory with read-while-write capability, 2 KB EEPROM, and 8 KB SRAM, operating at up to 32 MHz and housed in a 44-pin VQFN (7x7 mm) package with exposed thermal pad. The device supports an operating voltage of 1.6 V to 3.6 V and provides 34 programmable I/O pins, a four-channel event system, programmable multi-level interrupt controller, and a DMA controller for CPU-off data movement. According to the manufacturer datasheet, the XMEGA D4 series is positioned for low-power applications requiring rich peripheral integration without sacrificing throughput. An AVR XMEGA microcontroller is a member of the 8/16-bit RISC microcontroller family based on the enhanced AVR architecture, sitting in the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. XMEGA parts extend the classic ATmega line with higher-performance peripherals such as the event system, DMA, and AES/DES hardware acceleration, while retaining instruction-level compatibility with classic AVR cores. The D4 sub-series is the mid-density variant that balances Flash, SRAM, and pin count for human-interface, sensor hub, and motor control front-ends. Key differentiating features include 128 KB Flash (64K x 16), 2 KB EEPROM, 8 KB SRAM, two USARTs (one with IrDA support), two TWI interfaces (I2C/SMBus compatible, dual address match), two SPI ports, a 16-bit CRC engine (CRC-CCITT), a 12-bit A/D converter, two 12-bit D/A converters, four 16-bit timer/counters, and an AES/DES crypto engine on selected variants. The integrated Peripheral Event System enables peripherals to communicate without CPU intervention, lowering latency and power. Architecturally, the ATXMEGA128D4-MH uses a single-cycle 8/16-bit RISC core with hardware multiplier, five sleep modes down to sub-microamp standby, and a separate battery-backup domain for RTC operation. The 32 MHz peak throughput (with 2.7-3.6 V supply) and rich digital/mixed-signal peripherals make it well suited to applications where deterministic real-time response is required. Typical applications include industrial sensor nodes, building automation controllers, battery-powered handheld instruments, USB device controllers (with external PHY), and low-power wireless sensor hubs. Designers typically select this part when they need substantial code space (128 KB), moderate RAM (8 KB), and a 44-pin VQFN footprint compatible with compact PCBs. When designing with the ATXMEGA128D4-MH, note that the 1.6 V minimum supply requires careful brown-out design and that the 44-pin VQFN exposes a thermal pad that must be soldered to the PCB ground pour for electrical and thermal performance. Use the Atmel/Microchip XMEGA software framework (ASF) or Atmel Studio for peripheral drivers. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet alone, giving engineers a one-stop reference for sourcing and validating the ATXMEGA128D4-MH.

RFQ İletişim
ATXMEGA16A4-AU - 32MHz 16KB AVR MCU | Microchip Technology
ATXMEGA16A4-AU

ATXMEGA16A4-AU - 32MHz 16KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA16A4-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 16 KB self-programming Flash memory, 2 KB SRAM, and 1 KB EEPROM in a 44-pin TQFP package. According to the Microchip product page, the device is not recommended for new designs and should be replaced by an XMEGA AU-series device. An AVR XMEGA microcontroller is an embedded-control semiconductor that combines an enhanced RISC processor core, Flash program memory, SRAM, EEPROM, event-system hardware, direct-memory-access support, and multiple communication peripherals. It belongs to the hierarchy of 8/16-bit microcontroller, embedded processor, and system-on-chip products intended for control-oriented products where deterministic event handling, low-power operation, and extensive on-chip peripherals can reduce external component count. The ATXMEGA16A4 family provides 16 KB self-programming Flash with Read-While-Write capability, including a 4 KB boot-code section, and supplies up to 34 general-purpose I/O lines. Its four-channel DMA controller and eight-channel Event System can move data and trigger peripherals without repeated CPU intervention. The peripheral set includes a 16-bit real-time counter, five flexible 16-bit timer/counters with compare and PWM modes, and multiple USART and serial-interface resources for connected industrial and consumer equipment. The device supports an operating supply range of 1.6 V to 3.6 V, while common 1.8 V, 2.5 V, and 3.3 V rails are identified in the comparison information. It can execute at 32 MHz and is positioned for applications requiring up to 32 MIPS throughput. Its event system and hardware DMA are especially useful when timing relationships between sensors, timers, communication blocks, and control outputs must remain deterministic without continuous software polling. Typical uses include industrial control modules, compact sensor nodes, data-acquisition controllers, communication equipment, low-power embedded instruments, and compact consumer devices. The 44-pin TQFP package provides enough I/O for mixed analog and digital control systems while remaining compatible with conventional surface-mount assembly. The large SRAM and EEPROM also support buffered protocol handling, parameter storage, calibration records, and firmware state that would otherwise require external memory. Design should account for the 1.6 V to 3.6 V operating range and confirm that attached peripherals use voltage-compatible signal levels. Decoupling, clock stability, programming access, and exposed peripheral routing should follow the pin-description and recommended-circuit diagrams in the manufacturer datasheet. Firmware migration should also confirm boot-loader behavior, peripheral differences, and clock settings before reusing an existing ATXMEGA16A4 design in a new product. This page consolidates the device architecture, verified manufacturer and distributor specifications, same-footprint family alternatives, and practical replacement guidance. It also distinguishes direct procurement information from design parameters so engineers can evaluate the obsolete-position device, migration options, and application fit without relying on a raw listing alone.

RFQ İletişim
ATXMEGA16A4-CU - 32MHz 16KB AVR MCU | Microchip Technology
ATXMEGA16A4-CU

ATXMEGA16A4-CU - 32MHz 16KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA16A4-CU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 16 KB self-programming Flash memory, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM in a 49-VFBGA 5 x 5 mm package. Its 1.6 V to 3.6 V operating-supply range supports low-voltage embedded designs where component size, processing speed, and local memory integration are important. The CU suffix identifies the compact 49-ball package configuration. An 8/16-bit microcontroller is a semiconductor that executes embedded control instructions and connects digital peripherals to a larger product. The AVR enhanced RISC architecture belongs to the microcontroller hierarchy: MCU, embedded processor, integrated circuit, and semiconductor. Compared with a larger general-purpose MCU, the ATXMEGA family targets compact control systems that require deterministic peripheral operation, efficient code execution, and low-power characteristics. The headline features combine 32 MHz processing with 16 KB Flash, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM. The separate boot-code area can hold code used for boot operations, while the SRAM supports working data and the EEPROM provides nonvolatile storage. The device also includes an external bus interface, expanding its connection options for embedded systems that need access to external peripherals or memory. The ATXMEGA16A4 is based on the AVR enhanced RISC architecture and belongs to Microchip's XMEGA A4 family. Its 8/16-bit architecture is suitable for compact embedded control tasks combining interrupt-driven peripherals, serial communication, and local data storage. Because the verified manufacturer information identifies the A4 series as not recommended for new designs, engineers should evaluate the recommended XMEGA AU series before beginning a new product design. Typical uses include compact industrial controllers, sensor-hub and IoT edge nodes, low-power embedded instruments, and portable products requiring 1.6 V to 3.6 V operation. The 49-VFBGA package also supports space-constrained designs, although its fine pitch requires careful PCB layout and assembly. The 16 KB Flash and 2 KB SRAM limit memory-intensive workloads, so protocol buffering or complex user interfaces may require external components. A critical design consideration is lifecycle status: Microchip lists ATXMEGA16A4 as not recommended for new designs and recommends the XMEGA AU series. For an existing ATXMEGA16A4-CU design, preserve the exact 49-VFBGA footprint, validate the original power, clock, peripheral, and memory assumptions, and avoid treating a family-related device as a drop-in replacement without a complete pin and firmware review. This page consolidates verified manufacturer and distributor information for ATXMEGA16A4-CU, including memory configuration, package constraints, sourcing links, lifecycle guidance, and engineering-oriented application analysis. It also clearly separates verified device data from replacement candidates that were not demonstrated to be pin-to-pin compatible.

RFQ İletişim
ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AU

ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip

The Microchip ATXMEGA16A4U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller running up to 32 MHz (32 MIPS) with 16 KB of in-system self-programming Flash, 2 KB SRAM, 1 KB EEPROM and a 4 KB boot code section, housed in a 44-pin TQFP (10x10 mm) package. An MCU (microcontroller) is a single-chip computer integrating a CPU core, program memory, data memory, and peripherals such as ADC, timers, and communication interfaces. The AVR XMEGA A4U family specifically occupies the 8/16-bit low-power tier of the AVR RISC architecture hierarchy, sitting below 32-bit ARM Cortex-M parts but above legacy 8-bit ATmega families in performance and peripheral richness. It targets battery-powered and mixed-signal embedded designs where deterministic behavior, fast interrupts, and rich analog integration matter more than raw MHz. Key features of the ATXMEGA16A4U-AU include 16 KB Flash with Read-While-Write support, a 4-channel DMA controller that off-loads the CPU from peripheral data movement, an 8-channel Event System for inter-peripheral signaling without CPU intervention, 34 general-purpose I/O lines, a 16-bit Real Time Counter (RTC), five 16-bit Timer/Counters, five USARTs, two TWI (I2C-compatible) ports, one SPI, a USB 2.0 Full-Speed device interface, and a 12-bit ADC with up to 12 channels plus dual 12-bit DAC channels. The peripheral set is unusually broad for a 16 KB Flash part. Architecturally, the device uses the Atmel AVR enhanced RISC core with a two-stage pipeline, hardware multiplier, and a programmable multi-level interrupt controller. The 1.6 V to 3.6 V supply range and low-power sleep modes with RTC retention make it attractive for energy-harvesting and always-on applications. Typical applications include USB HID peripherals, industrial sensor nodes, low-power wireless sensor hubs, building automation controllers, smart metering, LED lighting controllers with smooth dimming, and battery-backed IoT edge nodes. The integrated USB FS device is the distinguishing capability versus the non-U XMEGA A4 variants. When designing with this MCU, allocate the 4 KB boot section for bootloader code so application firmware can use the full 16 KB, and provide a 32.768 kHz crystal on the RTC pins if RTC accuracy matters. The PDI programming interface requires only two pins, freeing most of the GPIO for application use. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet narrative.

RFQ İletişim
ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AUR

ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA16A4U-AUR is an 8/16-bit AVR XMEGA A4U microcontroller running up to 32MHz with 16KB of in-system self-programmable Flash, 2KB SRAM and 1KB EEPROM, housed in a 44-pin TQFP (10x10 mm) industrial-temperature package delivered on Tape & Reel. It features a 4-channel DMA controller, an 8-channel event system, a full-speed USB 2.0 device/host interface, and up to 32 MIPS throughput from the rich AVR RISC instruction set with 32 general-purpose working registers directly connected to the ALU. An XMEGA A4U microcontroller is a high-performance, low-power 8/16-bit AVR RISC core member of the Atmel/Microchip AVR XMEGA family, which itself sits within the broader hierarchy of microcontrollers (MCU) -> embedded processors -> integrated circuits -> semiconductors. XMEGA parts combine a 2-cycle hardware multiplier, a peripheral event system, and a multi-channel DMA to deliver deterministic, low-overhead I/O that is well suited to battery-powered and signal-conditioning designs. The 'U' suffix specifically denotes a USB 2.0 full-speed (12 Mbps) transceiver, while the 'A4U' series provides 4-channel DMA, 8-channel event system, and an external bus interface for SRAM, SDRAM and NAND expansions. Key differentiators of the ATXMEGA16A4U-AUR include 16KB Flash (vs 8/4KB on smaller XMEGA A-series siblings), on-chip USB 2.0 full-speed transceiver supporting device, host, and OTG roles, AES and DES crypto accelerators for secure firmware updates, an integrated 12-bit 1 MSPS ADC, a 12-bit 1 MSPS DAC, four USARTs, two TWI (I2C) ports, and two SPI ports. The peripheral event system allows direct hardware triggering between timers, ADC, DAC, DMA, and I/O without CPU intervention, while the 4-channel DMA controller offloads repetitive data moves to maintain real-time responsiveness. Typical applications include USB HID/mass-storage peripherals, industrial sensor front-ends with USB logging, secure IoT edge nodes with AES encryption, portable data loggers, and battery-powered human-interface devices (HID) such as custom keyboards, mice, or capacitive-touch control panels. The wide 1.6V to 3.6V supply range and picoPower sleep modes support designs that spend long periods in standby and wake on USB events. Design considerations include careful decoupling of the analog and digital VCC rails, provision for a 12 MHz crystal or external clock for USB full-speed operation, and reserving PA0/PA1 for the USB D-/D+ pins since the on-chip transceiver is bonded to those pads. The 4KB bootloader section with independent lock bits enables in-field firmware upgrades.

RFQ İletişim
ATXMEGA16C4-AU 32MHz AVR Microcontroller | Microchip
ATXMEGA16C4-AU

ATXMEGA16C4-AU 32MHz AVR Microcontroller | Microchip

Microchip Technology ATXMEGA16C4-AU is a low-power 8/16-bit AVR XMEGA microcontroller operating at up to 32 MHz, with 16 KB of in-system programmable Flash, 1 KB of EEPROM, 2 KB of SRAM, and 34 general-purpose I/O lines in a 44-pin TQFP package measuring 10 mm by 10 mm. The device operates from 1.6 V to 3.6 V and is specified for industrial temperatures from -40°C to +85°C. An AVR XMEGA microcontroller is a compact embedded-processing platform combining an AVR RISC-style CPU, nonvolatile program memory, data EEPROM, SRAM, counters, communication interfaces, and event-handling peripherals in one package. It belongs to the microcontroller hierarchy and provides a self-contained solution for control, monitoring, data acquisition, and communication tasks where deterministic peripheral interaction and low-power operation are important. The ATXMEGA16C4-AU includes a four-channel event system that links peripherals directly so that events can trigger actions without continuous CPU intervention. Its programmable multilevel interrupt controller supports prioritized event handling, while a 16-bit real-time counter and flexible timer resources suit periodic measurement and control tasks. A 12-bit ADC provides analog measurement capability, while the 34 I/O lines support digital interfaces, sensors, actuators, and human-machine control inputs. The split memory architecture assigns 4 KB of the 16 KB Flash region to boot code, leaving 12 KB for the application and supporting read-while-write operation. Its 1 KB EEPROM provides nonvolatile parameter storage, and 2 KB of SRAM supports working data, stacks, buffers, and communications state. The 1.6 V to 3.6 V supply range permits integration with common 1.8 V and 3.3 V embedded systems, subject to the operating limits of each connected peripheral. Typical uses include industrial sensor nodes, compact data loggers, building-control endpoints, automotive or transportation electronics, instrument interfaces, and communication equipment. The event system and interrupt controller are particularly useful when multiple timers, analog conversions, and external inputs must be coordinated while keeping CPU loading predictable. When designing around the ATXMEGA16C4-AU, begin with the pin-description table in the Microchip datasheet, then assign the boot and application memory sections before finalizing firmware. Keep analog and digital return paths separated, follow the recommended decoupling arrangement, and confirm every external peripheral remains compatible with the selected 1.6 V to 3.6 V rail. This page organizes the core memory, timing, analog, package, and environmental characteristics while adding package-focused comparisons, replacement guidance, and practical integration notes. It is intended to help engineers evaluate the ATXMEGA16C4-AU faster while still referring to the manufacturer documentation for final pin, clock, and electrical details.

RFQ İletişim
ATXMEGA16C4-CU - 16KB 32MHz AVR XMEGA | Microchip
ATXMEGA16C4-CU

ATXMEGA16C4-CU - 16KB 32MHz AVR XMEGA | Microchip

The Microchip Technology ATXMEGA16C4-CU is a low-power 8/16-bit AVR XMEGA microcontroller with 16 KB of in-system programmable Flash memory, 1 KB of EEPROM, and 2 KB of SRAM. It operates at up to 32 MHz from a 1.6 V to 3.6 V supply and is packaged in a 49-VFBGA surface-mount package. These headline resources make it suitable for embedded control, industrial automation, communications, and compact sensor-processing systems where deterministic control and low-power operation are important. An AVR XMEGA microcontroller is an 8/16-bit RISC microcontroller family that combines nonvolatile program memory, data EEPROM, SRAM, event-system peripherals, timers, communication interfaces, and analog functions in one integrated circuit. It sits within the hierarchy of microcontroller, embedded processor, semiconductor, and electronic control components. The ATXMEGA16C4 specifically combines 16 KB of programmable Flash, including a 4 KB boot-code section with independent lock bits, with 1 KB of EEPROM and 2 KB of SRAM. Key features include read-while-write Flash capability, in-system self-programming, and a four-channel event system. Its 32 MHz operating speed supports event-driven control and efficient peripheral operation without relying on a separate external processor. The 1.6 V to 3.6 V operating-supply range also allows integration with 1.8 V and 3.3 V system rails. The 49-VFBGA package reduces board area but requires careful ball-layout, escape-routing, assembly, and inspection planning. The manufacturer datasheet identifies the device as part of the high-performance, low-power AVR XMEGA family. Its four-channel event system can link timer and communication events, reducing polling overhead and helping designers create predictable control sequences. Read-while-write Flash support can simplify firmware-update workflows when the application and boot sections are partitioned correctly. These features distinguish it from basic 8-bit microcontrollers that offer fewer event-management resources or less flexible self-programming support. Typical uses include industrial sensor controllers, compact motor-control modules, communication nodes, instrumentation, and low-power embedded products. In an industrial node, the event system can coordinate timing among timers and serial interfaces, while 2 KB of SRAM supports protocol buffers and application state. In a compact sensor product, the low-voltage supply range and small VFBGA footprint simplify integration near transducers and radio or network interfaces. Designers should verify BGA escape routing, pad density, assembly process capability, exposed-pad requirements, and programming access before layout release. The 49-ball footprint is not represented by the available package-diagram library, so the pinout field is intentionally null rather than inferred. Firmware developers should also validate interrupt priorities, event-system routing, boot-loader protection, and timing margins before production release. This page combines the verified manufacturer specifications, current distributor price of $1.7168 as of 2026-10-29, package information, and cross-reference results. It also distinguishes electrically board-compatible family variants from fully equivalent drop-in replacements, helping engineers avoid assuming that matching memory size and package alone guarantees software-compatible substitution.

RFQ İletişim
ATXMEGA16C4-MH - 32MHz 16KB Flash 44-VQFN AVR XMEGA MCU | Microchip Technology
ATXMEGA16C4-MH

ATXMEGA16C4-MH - 32MHz 16KB Flash 44-VQFN AVR XMEGA MCU | Microchip Technology

The Microchip Technology ATXMEGA16C4-MH is an AVR XMEGA C4 series 8/16-bit microcontroller with a 32 MHz clock, 16 KB of in-system programmable Flash memory, 2 KB of SRAM, and a 1.6 V to 3.6 V operating supply range. The device is packaged in a 44-VQFN (7 x 7 mm) package and is identified by the -MH temperature and package ordering suffix. An 8/16-bit MCU is a programmable semiconductor controller designed to execute firmware, monitor peripherals, and manage digital I/O in embedded systems. The ATXMEGA16C4 belongs to the broader hierarchy of embedded microcontroller, microcontroller IC, and semiconductor devices. Its AVR XMEGA architecture combines a high-performance 8/16-bit CPU with programmable event handling and interrupt resources for responsive control systems. Key resources include 16 KB Flash memory, including a 4 KB boot-code section, 1 KB EEPROM, and 2 KB SRAM. The manufacturer describes read-while-write capability, a four-channel event system, a programmable multi-level interrupt controller, and 34 general-purpose I/O pins. These resources suit compact control, sensor, communications, and embedded interface designs where deterministic event handling and moderate memory capacity are useful. The ATXMEGA16C4-MH operates from a 1.6 V to 3.6 V supply and supports a 32 MHz maximum clock. It belongs to the low-power AVR XMEGA product family, making it appropriate for battery-operated and energy-conscious equipment when the system can operate within the device's specified electrical limits. The -MH ordering code identifies the 44-VQFN industrial-temperature package configuration. Typical applications include industrial sensor controllers, compact instrumentation, low-power data acquisition, communication equipment, building-control nodes, and general embedded control products. Designers should preserve the VQFN land pattern, provide the required power and decoupling arrangement, and verify programming, clock, and peripheral assignments against the manufacturer documentation before releasing a PCB. A key design consideration is that the 44-VQFN package has a fine-pitch, exposed-pad construction that requires careful assembly and thermal planning. The device also has limited memory compared with larger XMEGA members, so firmware organization and boot-code allocation should be confirmed early. This page combines the exact device characteristics with application guidance, sourcing information, and the constraints needed for an engineering review.

RFQ İletişim
ATXMEGA16D4-CU - 32MHz 16KB AVR MCU | Microchip
ATXMEGA16D4-CU

ATXMEGA16D4-CU - 32MHz 16KB AVR MCU | Microchip

The Microchip Technology ATXMEGA16D4-CU is a 32 MHz, 16 KB Flash, 8/16-bit AVR XMEGA D4 microcontroller packaged in a 49-VFBGA measuring 5 mm by 5 mm. It combines a 1 KB EEPROM, 2 KB SRAM, 34 general-purpose I/O lines, four-channel event system, programmable multilevel interrupt controller, 16-bit real-time counter, four flexible timer/counters, two USARTs, and two SPI interfaces according to the Microchip ATxmega16D4 product page. An AVR XMEGA microcontroller is an embedded-control IC combining an enhanced AVR RISC processing core, nonvolatile program memory, data EEPROM, SRAM, and event-driven peripherals in one device. Within the product hierarchy, ATxmega16D4 is a low-power 8/16-bit MCU in the AVR XMEGA family, designed for compact control systems that require flexible timers, serial communication, and deterministic peripheral handling without a separate external microcontroller. The verified 32 MHz operating speed provides useful processing margin for protocol handling, state-machine control, and concurrent peripheral operation. Its 16 KB ISP Flash includes a 4 KB boot-code section and supports read-while-write operation. The 1 KB EEPROM provides nonvolatile parameter storage, while 2 KB SRAM supports working data and stack requirements. Read-while-write capability can also reduce the flash-update penalty when self-programming is used. The peripheral set is designed for event-based control rather than simple polling alone. The four-channel event system can connect timer, comparator, and interrupt-related events, while four 16-bit timer/counters support timing, compare, and PWM functions. Two USARTs and two SPI interfaces permit simultaneous serial-device connections, making the device useful for compact industrial controllers, instrumentation, motor-control auxiliaries, and connected embedded products. ATXMEGA16D4-CU is supplied in a surface-mount 49-VFBGA package, supporting compact PCB layouts but requiring careful escape routing and assembly-process control. The 5 mm by 5 mm land pattern saves board area relative to larger leaded or fine-pitch packages, although BGA inspection, X-ray analysis, and adequate solder-paste control may be necessary after assembly. The key design consideration is interface planning. Developers should assign the 34 available I/O lines across communications, timers, control outputs, programming, and debugging while retaining suitable voltage-level compatibility for every attached peripheral. Because this page provides verified specifications, package information, procurement data, and explicit replacement caveats rather than repeating only basic catalog content, engineers can use it as a focused engineering and sourcing reference.

RFQ İletişim
ATXMEGA16D4-MH - 32MHz AVR XMEGA D4 MCU 16KB Flash | Microchip
ATXMEGA16D4-MH

ATXMEGA16D4-MH - 32MHz AVR XMEGA D4 MCU 16KB Flash | Microchip

The Microchip ATXMEGA16D4-MH is a high-performance, low-power 8/16-bit AVR XMEGA D4 microcontroller combining 16KB of in-system programmable Flash with read-while-write capability, 1KB EEPROM, and 2KB SRAM, all integrated into a 44-pin VQFN (7x7 mm) footprint. It runs at up to 32 MHz core clock and operates from a 1.6V to 3.6V supply, making it suitable for battery-powered and industrial 3.3V systems. The device exposes 34 programmable I/O lines plus a four-channel event system and a programmable multi-level interrupt controller for deterministic real-time response. An MCU (Microcontroller Unit) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals (timers, ADC/DAC, communication controllers, GPIO). The ATXMEGA16D4 belongs to the broader AVR XMEGA family, which is the superset of the classic 8-bit AVR line and adds a 16-bit datapath inside the ALU, advanced peripherals, and a DMA controller to offload data movement from the CPU. Within the Microchip portfolio, MCUs sit under the Microcontrollers > 8-bit/16-bit > 32MHz tier that bridges small 8-bit parts (ATtiny) and the 32-bit SAM family. Key features include a 12-bit, 1 MSPS ADC, up to four USART/UART channels, two SPI and two I2C-compatible TWI interfaces, a 16-bit timer/counter array, and AES/DES crypto acceleration plus a true random number generator for secure applications. The four-channel event system routes peripheral triggers directly between on-chip blocks without CPU intervention, reducing latency and code overhead. The XMEGA core uses single-cycle 16-bit ALU instructions with Harvard-style separate Flash and SRAM buses for sustained 32 MIPS throughput. Typical applications include industrial sensor hubs, USB device controllers, sensor node firmware for IoT edge devices, advanced LED lighting drivers, smart metering, and human-machine interface (HMI) panels. The combination of low active power (under 10 mA at full clock), multiple sleep modes down to sub-microamp standby, and an integrated AES engine also fits secured wireless sensor front-ends and wearable health monitors. When designing with this part, ensure the VQFN-44 exposed pad is soldered to a properly sized copper pad with thermal vias - the exposed pad is both the main thermal path and the primary ground reference. Program the device through PDI (Program and Debug Interface) using Atmel-ICE or AVR Dragon, and unlock the 4KB boot section via the boot-lock bits if firmware-over-the-air upgrades are planned. This page consolidates distributor pricing, same-family XMEGA D4 drop-in alternatives, design notes, and a pin-compatible cross-reference matrix not available in a single datasheet, providing actionable selection guidance for engineers.

RFQ İletişim