ڈیولپمنٹ بورڈز
مصنوعات (190+)
XR75100EVB - 40V Sync Buck COT Eval Board | MaxLinear
The MaxLinear XR75100EVB is an evaluation board for the XR75100 40V synchronous step-down Constant On-Time (COT) controller, delivering up to 20A point-of-load output from a wide 5.5V to 40V input range. The board operates as a single non-isolated DC/DC step-down reference design, supporting industry-standard 12V, 18V, and 24V DC and AC rails, and is housed in a compact SMPS evaluation form factor built around the XR75100 controller IC. An evaluation board (EVB) is a fully assembled reference design PCB that lets engineers power up, probe, and characterize a target IC without designing their own layout. EVBs accelerate time-to-market by exposing key test nodes (input, output, SW node, GND, EN) and by using manufacturer-recommended external components - inductors, capacitors, MOSFETs - so that performance numbers (efficiency, ripple, load step, thermal) measured on the bench can be reproduced in production designs. The XR75100EVB is targeted at industrial power evaluation, where 24V to 5V/3.3V intermediate buses are standard. Key features include a 5.5V to 40V input range, up to 20A output current at the point-of-load, and a proprietary emulated current-mode COT control scheme that delivers extremely fast line and load transient response with ceramic output capacitors. The reference design is specified for industrial-grade operating conditions and demonstrates synchronous rectification with internal MOSFET drivers. According to the MaxLinear product page, the XR75100 supports programmable switching frequency, soft-start, and fault protection including over-current, over-voltage, and thermal shutdown. The board leverages MaxLinear's emulated current-mode architecture, which simulates peak current-mode control without an external current-sense resistor, reducing losses and board area. COT control inherently rejects line transients within a single switching cycle, and emulated current mode adds a synthetic ramp that enables stable operation with very-low-ESR ceramic output capacitors - a combination that simplifies BOM and improves loop bandwidth versus traditional voltage-mode controllers. The result is a tight transient response suitable for powering FPGAs, ASICs, and DSP cores that demand <1% voltage excursion under load step. Typical applications include industrial automation PLC and motor-drive 24V intermediate bus conversion, telecommunications and networking equipment point-of-load regulation, and automotive 12V/24V accessory rails. The 40V absolute-maximum input withstands 24V nominal rails plus transients without surge suppression, making the XR75100EVB a strong choice for factory floor and telecom-shelf environments. When designing with this reference, populate input bulk capacitance for the worst-case load step, select the inductor per the XR75100 datasheet ripple-current guideline (typically 30% of IOUT), and ensure the exposed thermal pad of any controller-sourced variant receives sufficient copper pours. Note that the EVB is intended for lab characterization - production designs should reuse the schematic and BOM rather than copy the PCB layout exactly. This page synthesizes distributor pricing, manufacturer specifications, and application context for the MaxLinear XR75100EVB that go beyond a single datasheet download, helping you decide whether this COT-based evaluation reference suits your 24V-bus point-of-load design.
ZP3-18RT - 3.7" HMI+PLC Integrated 10DI/8DO Relay+Transistor | Xinje
The Xinje ZP3-18RT is a 3.7-inch integrated HMI+PLC all-in-one controller combining a text-panel HMI with a programmable logic controller in a single DIN-rail-mountable housing. It ships with 10 digital inputs (DI), 8 digital outputs (DO) configured as 8 relay+transistor mixed outputs, and is powered from a DC 24 V supply at 3 W typical consumption. An RS485 port supports Modbus RTU / ASCII master/slave communication and free-format protocols for sensor and variable-frequency-drive integration. Background knowledge: A combined HMI+PLC (often called an integrated controller, text panel PLC, or all-in-one PLC) is a compact industrial-control device that merges the operator interface (HMI) and the logic execution unit (PLC) into one enclosure. The hierarchy sits as: PLC -> industrial controller -> factory automation device; HMI -> operator interface -> factory automation device. Combining them saves panel space, reduces wiring between separate HMI and PLC units, and lowers bill-of-material cost in small machine-control applications such as packaging, textiles, and OEM skid equipment. Key features include the integrated LCD text display, the mixed relay-and-transistor output bank (eight points that combine electromechanical relays with semiconductor switching), the Modbus RTU / ASCII + free-format serial protocol support, and the DIN-rail form factor. The unit accepts a 24 VDC supply (typical tolerance as published by Xinje), provides an RS485 port for fieldbus networking, and the relay outputs allow direct switching of AC or DC loads while the transistor outputs deliver high-cycle life for solenoid, indicator, and small-motor loads. Technically, the ZP3 series belongs to Xinje's ZP3 text-display PLC family with integrated BD-board expansion and supports ladder / instruction-list programming on the Xinje software platform. Real-time clock, BD expansion, and BD-board peripheral add-ons are supported via the side expansion connector, and the part is designed to operate across the industrial temperature range Xinje publishes for the ZP3 family. Typical applications include small-form packaging machinery, textile and embroidery machines, OEM skids for HVAC and pumping stations, material-handling conveyors, and small process-control panels where an integrated HMI+PLC replaces a separate HMI-and-PLC stack. Modbus RTU connectivity also makes the ZP3-18RT a low-cost Modbus slave for SCADA retrofits. When designing with this controller, confirm the load ratings of the relay outputs (resistive vs inductive derating) and the transistor output sink/source topology from the official Xinje datasheet before assigning mission-critical outputs, because mixed output banks impose different switching lifetimes. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives in the XP1/XP2/XP3 series, and practical engineering notes not aggregated in the Xinje datasheet alone.
cMT3152S - 15-Inch Capacitive HMI | Maple Systems
Maple Systems cMT3152S is a 15-inch wide-viewing-angle human-machine interface with a 1024 × 768 color capacitive touchscreen, tempered-glass front panel, and an integrated industrial controller. The verified family information identifies a quad-core Cortex-A17 CPU operating at 1.6 GHz, a dedicated 3D processor, and 4 GB of built-in flash memory for local HMI projects and data storage. An SD card slot provides expandable storage. The panel is designed for machine control, operator supervision, and IIoT-enabled remote access. A human-machine interface, or HMI, is the operator-facing element of an industrial control system. It combines a display, touch input, processing capability, communications, and configurable software to present machine status, accept commands, visualize processes, and support diagnostics. Within the industrial automation hierarchy, an HMI sits above PLCs, sensors, drives, and remote I/O while translating real-time process data into screens that operators can use safely and efficiently. The verified cMT3152X family highlights include a 15-inch WVA display, 1024 × 768 resolution, capacitive touch, tempered glass, and a quad-core Cortex-A17 1.6 GHz CPU. Communications include COM1 and COM3 RS-485 two-wire connections supporting MPI at 187.5 kbit/s; only one interface should be used at a time. When COM3 RS-232 is also used, the verified datasheet states that COM1 RS-232 may use transmit and receive only because RTS and CTS are unavailable. A built-in power isolator supports robust industrial integration. The front panel is identified as NEMA 4 and IP66 compliant, making it suitable for installations requiring resistance to dust and water ingress from the panel side. Its capacitive touchscreen supports modern touch interactions, while the integrated graphics processor supports the advanced visualization features associated with the cMT platform. Exact electrical ratings, power input limits, dimensions, viewing-angle values, memory-expandability limits, and environmental limits were not included in the provided target-specific evidence and must be confirmed from the applicable manufacturer documentation before design release. Typical installations include production-line control, machine diagnostics, recipe selection, process monitoring, remote equipment supervision, and centralized factory-floor operator stations. The large 15-inch format is useful where operators must view several process variables at once, and the 1024 × 768 native resolution provides a practical platform for detailed diagrams and alarm summaries. Remote access and IIoT capabilities make the panel relevant for connected automation projects where authorized users need visibility beyond the immediate enclosure. For panel integration, verify the target-specific rear and side interfaces, mounting cutout, supply voltage, power consumption, grounding requirements, environmental ratings, and serial-port wiring before fabrication. Treat the cMT3152S suffix as a potentially orderable configuration variant and confirm that it corresponds to the exact hardware and software bundle required by the project; the supplied search evidence primarily documents cMT3152X and cMT3152Xv2 family variants. This product summary distinguishes verified cMT3152X-family capabilities from target-specific data that remains unavailable, while connecting the hardware to practical HMI integration, communications, storage, and panel-protection decisions.
dsPIC33CK32MP503T-I/M5 - 100MHz 32KB DSC | Microchip
The Microchip Technology dsPIC33CK32MP503T-I/M5 is a 16-bit digital signal controller (DSC) from the dsPIC33CK family operating at up to 100 MHz, with 32KB of Flash program memory and 8KB of RAM, housed in a 36-pin UQFN (5x5 mm) package with exposed pad. A digital signal controller combines the computational capability of a digital signal processor with the peripheral set and ease of use of a microcontroller. In the power management hierarchy, the dsPIC33CK sits above basic MCUs and is purpose-built for closed-loop digital power conversion, motor control, and advanced sensing, where deterministic interrupt latency and high-resolution timing are essential. Key features include a 100 MHz dsPIC DSC core with DSP engine, 3x2 high-speed PWMs with 2 ns effective resolution for precise switching control, a 12-bit/3.5 Msps ADC supporting 15 channels, three integrated analog op amps, three analog comparators, a 12-bit DAC, and CAN Flexible Data (CAN FD) serial connectivity. Peripheral Trigger Generator (PTG) support enables autonomous, CPU-light peripheral sequencing. Architecturally, the dsPIC33CK core uses an enhanced 16-bit Harvard architecture with zero-overhead looping and hardware multiply-accumulate, executing control loops in the tens of microseconds. The -I temperature suffix qualifies the device for -40C to +125C operation on a 3.0V to 3.6V supply, and the device is offered in a Functional Safety (FuSa) supported variant suitable for industrial safety designs. Typical applications include digital switch-mode power supplies (AC-DC, DC-DC), PFC stages, brushless DC and PMSM motor drives, and CAN FD networked industrial control nodes. Design consideration: the 36-pin UQFN 5x5 mm package concentrates VDD/VSS and analog pins on specific corners; follow the Microchip reference layouts and place the 12-bit ADC's dedicated analog supply decoupling close to the pins for the full 3.5 Msps performance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.