EPM570F100I5
EPM570F100I5 - MAX II CPLD, 440 LE, 76 I/O, 100-FBGA | Intel
The Intel (formerly Altera) EPM570F100I5 is a MAX II family Complex Programmable Logic Device (CPLD) featuring 440 logic elements, 76 user I/Os, and 201.1 MHz maximum internal frequency, packaged in a 100-ball FineLine BGA (FBGA-100). It is fabricated on a 0.18 µm process and supports 2.5 V / 3.3 V mixed-voltage operation for the core and I/O banks. The MAX II architecture is built on a non-volatile Flash look-up table (LUT) array with instant-on functionality and in-system programmability via JTAG (IEEE Std. 1149.1).
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the hierarchy between simple glue-logic PAL/GAL chips and large FPGAs. CPLDs use a programmable AND/OR array with non-volatile configuration memory, providing deterministic, single-clock-cycle propagation delays and instant power-on behavior. MAX II devices specifically use a LUT-based architecture (rather than classic PLA) combined with on-chip Flash configuration to deliver FPGA-like density at CPLD-like simplicity - making them ideal for I/O expansion, bus bridging, interface protocol translation, and power-sequencing logic that must be active immediately at system power-up.
Key features of the EPM570F100I5 include 440 logic elements (LEs), 440 macrocells, 76 user I/O pins, and an internal operating frequency of 201.1 MHz. The device integrates 8 Kbits of user Flash memory (UFM) for storing non-volatile data such as serial numbers, calibration constants, or boot parameters. Multi-voltage I/O banks support 1.5 V, 1.8 V, 2.5 V, and 3.3 V interfaces, allowing direct connection to legacy 5 V-tolerant buses through proper external components. The JTAG-based in-system programmability (ISP) eliminates the need for a separate boot PROM and supports IEEE 1149.1 boundary-scan testing.
Architecturally, the MAX II device uses a uniform interconnect matrix that routes LUT outputs to I/O pins with predictable, fast timing. Every LE includes a 4-input LUT, a programmable register, and a carry chain. The integrated Flash configuration block is in-system programmable through JTAG and supports JTAG-based verification during production test. The UFM block provides a small non-volatile memory that can be accessed from user logic, eliminating the need for a separate EEPROM in many designs.
Typical applications of the EPM570F100I5 include I/O expansion and level translation in industrial control systems, bus protocol bridging (I2C-to-SPI, UART-to-PCI), LED display and lighting control sequencing, power-supply management and hot-swap control logic, JTAG-based test access port (TAP) multiplexing, and general glue-logic replacement in consumer and embedded designs. The instant-on, deterministic-timing characteristics make it especially valuable in power-rail sequencing for processor cores, memory subsystems, and complex SoCs that require controlled bring-up.
When designing with the EPM570F100I5, pay careful attention to the FBGA-100 PCB footprint - a 1.0 mm ball pitch requires precise land pattern design and reflow profile control. Use the Altera/Intel Quartus II design software (legacy) or Quartus Prime to develop, simulate, and program the device; the JTAG interface supports in-system programming after PCB assembly. Provide proper decoupling on each VCCINT and VCCIO bank and follow Intel's recommended BGA routing escape pattern to minimize via stubs and signal-integrity issues on high-speed outputs.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical BGA-layout design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and designing with the EPM570F100I5.
RFQ
رابطہ