Vi điều khiển

Sản phẩm (20.000+)

P1011NXN2DFB - QorIQ P1 PowerPC e500v2 MPU, 800MHz, 689-TEPBGA | NXP
P1011NXN2DFB

P1011NXN2DFB - QorIQ P1 PowerPC e500v2 MPU, 800MHz, 689-TEPBGA | NXP

The NXP P1011NXN2DFB is a QorIQ P1 series PowerPC e500v2 microprocessor with a single 32-bit core running at 800MHz, integrated into a 689-ball TEPBGA II (31x31 mm) package. It supports DDR2/DDR3 memory with ECC, integrates GbE, PCIe, USB, and TDM interfaces, and operates from -40C to +125C in Revision 1.1 silicon. A microprocessor (MPU) is a single-chip CPU that integrates a processing core, cache, memory controller, and peripheral interfaces into one package. QorIQ P1 series parts belong to NXP's Power Architecture communications-processor family; they sit beneath the P2 tier in the QorIQ hierarchy and represent the lowest-power single-core option for Ethernet-attached networking equipment. Key features of the P1011NXN2DFB include 32 KB I-cache and 32 KB D-cache per core, 256 KB of L2 cache with ECC, a 64-bit DDR2/DDR3 SDRAM memory controller with ECC support, dual triple-speed Ethernet (1/2.5 Gbps capable), a PCIe interface, USB 2.0, two TDM ports, and a Security Engine for protocol acceleration. The 689-TEPBGA package exposes all of these interfaces plus JTAG, GPIO, and SerDes, giving board designers a single SoC for managed industrial gateways. The P1011 silicon combines a Power Architecture e500v2 super-scalar core clocked up to 800 MHz with hardware accelerators and on-chip SRAM. Compared with the dual-core P1020, P1011 halves the core count but retains the same peripherals and is pin-compatible within the 689-TEPBGA footprint, letting customers scale board designs without changing the PCB. Typical applications include industrial Ethernet switches, factory-floor protocol gateways, smart-grid substation equipment, networked PLC controllers, and small-form-factor industrial routers. The -40C to +125C operating range and the integrated GbE/PCIe/USB bring-up simplicity also suit outdoor cellular backhaul and SCADA remote terminal units. When designing with this device, allocate adequate PCB layer count (typically 8-10) for the 689-ball BGA fan-out and follow NXP's reference decoupling scheme (1 uF and 100 nF near each power rail). NXP's QorIQ P1 hardware design checklist should be consulted to validate SerDes reference-clock jitter and DDR3 fly-by routing rules.

RFQ Liên hệ
P1012NSE2FFB - QorIQ P1012 800MHz SoC | NXP | Networking
P1012NSE2FFB

P1012NSE2FFB - QorIQ P1012 800MHz SoC | NXP | Networking

The NXP P1012NSE2FFB is a QorIQ P1 series single-core communications processor built on a Power Architecture (e500v2) 32-bit core running at 800MHz, housed in a 689-ball TEBGA II package (31x31 mm). It integrates GbE, DDR2/DDR3 memory controller with ECC support, PCIe, USB, TDM, QUICC Engine, and SEC security engine, and is rated for 0C to 125C operation at silicon revision 1.1. A communications SoC (System-on-Chip) is a highly integrated processor that combines CPU cores, memory controller, networking interfaces, and security accelerators on a single die. The QorIQ P1 family, which includes the P1012 single-core variant and the P1021 dual-core variant, targets cost-effective networking equipment. Within the broader power architecture ecosystem, the P1012 sits between the lower-frequency P1011 and the higher-end P2020, providing a 4.5x aggregate frequency range across the QorIQ P1/P2 platforms. Key differentiating features include the integrated QUICC Engine for TDM/HDLC offload, the SEC 4.x crypto engine for IPsec/SSL acceleration, hardware ECC for DDR2/DDR3 memory integrity, and a flexible SerDes supporting multiple GbE, PCIe, and SGMII configurations. The 45nm process technology delivers strong performance-per-watt for thermally constrained networking appliances. Architecturally, the P1012 uses a classic e500v2 core with dual-issue superscalar pipeline, integrated L1 cache, and a 256KB unified L2 cache. The platform's coherence fabric and integrated I/O controllers allow OEMs to build routers, switches, and secure gateways with minimal external logic, reducing BOM cost and PCB complexity. Typical applications include industrial routers and secure gateways, network attached storage (NAS) controllers, factory automation controllers with Ethernet, line-rate packet inspection appliances, and compact T1/E1 termination equipment. The wide temperature range and integrated SEC engine also make it suitable for industrial automation and secure edge appliances. Designers should note that this part has reached end-of-life per the NXP product page; long-life-cycle systems should select the P1012NSE2HFB (extended temperature) variant or plan for last-time-buy sourcing. The 689-TEBGA II package requires careful PCB layout for power delivery and DDR3 signal integrity. This page synthesizes distributor stock levels, pin-compatible NXP alternatives from the QorIQ P1/P2 families, and practical thermal/PCB design notes not found in the manufacturer datasheet alone.

RFQ Liên hệ
P1012NSE2HFB - QorIQ P1 800MHz e500v2 SoC MPU | NXP
P1012NSE2HFB

P1012NSE2HFB - QorIQ P1 800MHz e500v2 SoC MPU | NXP

The NXP P1012NSE2HFB is a QorIQ P1 series single-core PowerPC e500v2 communications microprocessor running at 800MHz, packaged in a 689-ball TEPBGA II (31x31 mm) with an exposed thermal pad. It integrates GbE, DDR2/DDR3 with ECC controllers, PCIe, USB, TDM, QUICC Engine (QE), and SEC security accelerators into a single 45 nm SoC, delivering extensive integration for networking, telecom, defense, and industrial applications. A microprocessor (MPU) is an integrated circuit that contains the central processing unit of a computing system. In the embedded hierarchy, an MPU sits above microcontrollers (MCUs) in complexity: MPUs integrate a CPU core plus system interfaces (memory controllers, high-speed serial links, DMA, security) and typically require external memory and power management, while MCUs bundle memory and peripherals on-die. The QorIQ P1 series targets space- and power-constrained networking/industrial designs where a full multi-core CPU is unnecessary but high-speed I/O and protocol offload are required. Key features include an 800MHz e500v2 core with dual-issue superscalar execution, integrated GbE, DDR2/DDR3 controller with ECC, three PCIe Gen 2 controllers, two USB 2.0 ports (host + device), four TDM interfaces, QUICC Engine for protocol offload, and SEC 4.0 hardware cryptography. The 689-TEPBGA II exposed-pad package provides a low thermal resistance path suitable for fanless industrial designs operating at 0C to 125C junction. The P1012 uses a 45 nm low-power CMOS process with NXP's Data Path Acceleration Architecture (DPAA) primitives and Trust Architecture 1.0 secure boot. The 800MHz core delivers ~1.6 DMIPS/MHz class performance per core while keeping typical power around 4-6W, making it suitable for sealed enclosures. Hardware ECC on the DDR controller supports DRAM reliability for telecom and industrial workloads. Typical applications include industrial Ethernet switches, secure routers, defense communication gateways, factory automation controllers, smart-grid substation equipment, and embedded network appliances. The QE block offloads TDM/HDLC/ATM/UART traffic without CPU intervention. When designing with the P1012, allocate the exposed-pad thermal land with a minimum 6x6 via array to keep junction temperature within the 125C limit. Use NXP's QCVS or CodeWarrior toolchains and reference the P1012DS datasheet for DDR3 trace length matching, SerDes reference clock jitter, and SEC boot fuse programming. This page synthesizes verified distributor pricing, drop-in same-family alternatives, and practical layout notes not consolidated in the manufacturer datasheet.

RFQ Liên hệ
P1012NSN2DFB - QorIQ P1 PowerPC e500v2 MPU 800MHz | NXP
P1012NSN2DFB

P1012NSN2DFB - QorIQ P1 PowerPC e500v2 MPU 800MHz | NXP

The NXP P1012NSN2DFB is a QorIQ P1 series single-core PowerPC e500v2 microprocessor running at up to 800 MHz, housed in a 689-pin TEBGA II (31x31 mm) package with exposed pad. Built on a 45 nm low-power process, this communications SoC integrates DDR2/DDR3 memory controllers with ECC, Gigabit Ethernet, PCI Express, USB 2.0, TDM, and a QUICC Engine (QE) for protocol offload. A microprocessor (MPU) is a single-chip CPU containing arithmetic logic, control logic, registers, and often integrated peripherals, distinct from a microcontroller by its higher external memory bandwidth and lack of on-chip flash. The P1012 sits within the broader taxonomy of Power Architecture embedded processors -> communications processors -> networking SoC, positioning it as a higher-integration successor to classic PowerQUICC devices while remaining within NXP's broader embedded computing portfolio. Key features include a 32-bit e500v2 core with double-precision floating point, hardware ECC for both the L1 cache and DDR memory interface, dual GbE controllers, three PCI Express Gen 1 controllers, two USB 2.0 controllers (host + device), and a dedicated QUICC Engine subsystem supporting UTOPIA / TDM interfaces for legacy telecom. Operating temperature range spans 0C to 125C (junction), qualifying the part for thermally demanding industrial and networking environments. The P1012 implements a hierarchical memory architecture with 32 KB L1 instruction cache and 32 KB L1 data cache per core, a 256 KB L2 platform cache, and a 32-bit DDR2/DDR3 memory controller with on-die ECC. The platform is architected for deterministic interrupt latency required by real-time control planes, with low-jitter timers and hardware-accelerated cryptography (SEC 3.1). Typical applications include industrial routers, factory-floor switches, defense radios, smart-grid gateways, line cards for mid-range networking equipment, and protocol-conversion appliances. The integrated QUICC Engine makes it especially suited to legacy T1/E1 and HDLC-based telecom equipment where discrete FPGAs would otherwise be required. When designing with the P1012, ensure the PCB provides a continuous ground plane under the TEBGA-689 exposed pad and that the DDR memory layout follows the fly-by topology specified in the NXP hardware reference manual. The core voltage and DDR voltage rails must ramp in the order documented in the datasheet to avoid latch-up during power sequencing. This page synthesizes current distributor pricing, drop-in alternative listings, and practical design notes not found in the manufacturer datasheet itself, drawing on NXP product documentation, Octopart inventory, and verified distributor listings.

RFQ Liên hệ
P1012NSN2HFB - QorIQ P1012 800MHz e500v2 MPU | NXP | Networking
P1012NSN2HFB

P1012NSN2HFB - QorIQ P1012 800MHz e500v2 MPU | NXP | Networking

The NXP P1012NSN2HFB is a PowerPC e500v2-based QorIQ P1 single-core communications microprocessor operating at up to 800 MHz, packaged in a 689-pin TEBGA II (31x31 mm) with exposed pad for thermal dissipation. The device integrates a 32-bit RISC core with high-performance peripherals including GbE, DDR2/DDR3 memory controllers with ECC, PCIe, USB, TDM, and the QUICC Engine (QE) for protocol acceleration. What is a QorIQ communications MPU? A QorIQ microprocessor is a system-on-chip (SoC) processor family from NXP (formerly Freescale) designed for embedded networking, telecom, and industrial control applications. QorIQ P1 platform parts integrate one or more PowerPC e500 cores with packet processing accelerators, security engines, and multiple high-speed serial interfaces on a single die. They sit in the product hierarchy between microcontrollers (MCU) and application processors (AP), combining deterministic real-time control with rich connectivity. Key features include the single e500v2 core running at 800 MHz, integrated GbE MACs, hardware-accelerated cryptography, the QUICC Engine for TDM/HDLC/UART protocol termination, dual USB 2.0 ports, and dual PCIe Gen1 controllers. The memory subsystem supports DDR2/DDR3 with ECC for high-reliability designs. The -N suffix indicates the commercial 0 to 125C temperature range, while the NSN2 designation corresponds to NXP's revision 1.1 die revision. The architecture is built on 45 nm process technology, balancing performance and power for fan-less industrial and networking equipment. The integrated QUICC Engine offloads communications protocol processing from the core, freeing CPU cycles for control plane and application software. Hardware queue management and pattern matching accelerate deep packet inspection workloads. Typical applications include industrial routers and gateways, defense and aerospace communications platforms, telecom edge equipment (DSLAM, GPON ONT), networked printers, and factory automation controllers. The integrated peripherals reduce BOM cost and board area compared to discrete processor-plus-ASIC designs. When designing with this device, ensure the PCB provides adequate thermal relief to the 689-ball exposed pad; the die dissipates significant power at 800 MHz. Use the NXP P1021/P1012 Modular Development System to accelerate software bring-up, and follow the hardware specification for DDR3 trace length matching and SerDes reference clock jitter requirements. This page synthesizes distributor pricing across 19 sources, drop-in and same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing, replacement, and design decisions on the QorIQ P1012 platform.

RFQ Liên hệ
P1013NSE2EFB - QorIQ P1 1.055GHz PowerPC e500v2 MPU | NXP
P1013NSE2EFB

P1013NSE2EFB - QorIQ P1 1.055GHz PowerPC e500v2 MPU | NXP

The NXP (formerly Freescale) P1013NSE2EFB is a PowerPC e500v2 microprocessor in the QorIQ P1 communications platform family, delivered in a 689-ball TEPBGA-II (31x31 mm) package. It integrates a single 32-bit e500v2 core running up to 1.055 GHz, hardware-accelerated encryption (SEC), Gigabit Ethernet, PCI Express, USB 2.0, DDR2/DDR3 memory controller with ECC, and an LCD controller. Operating temperature is industrial-grade, suitable for networking and industrial embedded systems. A microprocessor (MPU) is a single-chip CPU that integrates the core, cache, memory controller and peripheral interfaces onto one silicon die. Within the broader taxonomy, the P1013 sits inside the PowerPC -> embedded MPU -> communications processor -> system-on-chip (SoC) hierarchy, evolving from the PowerQUICC II/III family. QorIQ P1 parts are optimized for entry-to-mid-range networking appliances where deterministic packet processing, low power, and integrated security matter more than raw multi-core throughput. Key differentiating features include a 600/400/667 MHz bus/core configuration (the E2 suffix indicates the speed grade bin), integrated SEC 4.4 engine for IPSec, SSL, and 3GPP cipher offload, dual GbE MACs with IEEE 1588 timestamp support, four PCI Express Gen 1 lanes, DDR2/DDR3 SDRAM controller with 32-bit data width and ECC, and an integrated LCD controller for HMI panels. Hardware virtualization is supported via embedded hypervisor extensions, and Trusted Boot via the SEC engine. The e500v2 core is a superscalar, out-of-order Power Architecture implementation with Book E enhancements, dual-issue pipelines, and 32 KB L1 instruction and data caches plus a 256 KB unified L2 cache with ECC. The platform integrates all standard QorIQ peripheral IP, allowing single-chip designs that previously required an MPU plus an external PHY/MAC bridge. Power consumption is governed by the on-platform DPAA (Data Path Acceleration Architecture) and dynamic frequency switching. Typical applications include industrial routers, protocol converters, substation gateways, sub-1 GHz line-rate firewalls, network-attached storage SoCs, factory automation PLCs with HMI, and secure point-of-sale terminals. The integrated SEC engine and GbE make it a fit for VPN concentrators and IEC 61850 substation controllers, where determinism, reliability, and cryptography matter more than compute density. When designing with the P1013NSE2EFB, allocate the full 31x31 mm PCB footprint for the 689-ball TEPBGA, route DDR traces with matched impedance, and follow the NXP hardware specifications for DDR3 fly-by topology. The part requires careful thermal relief even at modest TDP, and a 6-layer or denser stack-up is recommended for signal integrity on PCIe and SERDES lanes. This page synthesizes distributor pricing, drop-in P1-family alternatives, and practical design notes drawn from the NXP QorIQ P1013 reference manual — context that goes beyond a single datasheet.

RFQ Liên hệ
P1013NSE2HFB - QorIQ P1 800MHz SoC | NXP Semiconductors
P1013NSE2HFB

P1013NSE2HFB - QorIQ P1 800MHz SoC | NXP Semiconductors

The NXP Semiconductors P1013NSE2HFB is a QorIQ P1 Power Architecture system-on-chip (SoC) with a single e500v2 core at up to 800 MHz (also specified as 1.055 GHz core clock in some sources) housed in a 689-ball TEPBGA II package (31x31 mm). It integrates Gigabit Ethernet, PCIe, USB, DDR2/DDR3 memory controller with ECC, security engine, and LCD controller for IP networking and advanced media processing. QorIQ P1 series SoCs belong to the communications processor family, sitting within the broader Power Architecture microprocessor taxonomy (Power Architecture -> MPU -> microprocessor -> IC). These parts target embedded networking, industrial control, and secure media processing workloads where integration reduces BOM and board area versus discrete CPU + Northbridge designs. Compared to traditional host processors, QorIQ P1 devices trade multi-GHz performance for deterministic real-time response and rich connectivity peripherals. Key features include an 800/667/400 MHz triple-speed e500v2 core with 36-bit physical addressing, integrated security engine (SEC) for IPsec, SSL/TLS, and bulk cryptography, dual GbE controllers with SGMII support, PCIe Gen 2.0 endpoint/root complex, USB 2.0 with ULPI, and a 16-bit DDR2/DDR3 memory controller with ECC up to 800 MT/s. The LCD controller supports TFT panels up to WXGA resolution. Power dissipation typically runs around 4-6 W depending on frequency grade and operating conditions. Architecturally, the P1013 uses a 45 nm low-power CMOS process with hardware-accelerated cryptography blocks offloaded from the core. The e500v2 core includes double-precision FPU, MMU, and 32 KB L1 I-cache plus 32 KB L1 D-cache. Fabric is a coherent CoreNet platform supporting concurrent DMA, security, and packet processing without saturating the CPU. Typical applications include industrial gateways, secure routers, factory automation controllers, network-attached storage (NAS), point-of-sale terminals, single-board computers (SBC), and Human-Machine Interface (HMI) panels. The integrated GbE and SEC make it especially suitable for VPN concentrators and firewalls where hardware crypto offload is essential. When designing, ensure proper thermal management with at least 4-layer PCB and thermal vias under the exposed pad. Use ECC-enabled DRAM for reliable operation in industrial temperature range. Configure SEC early in boot to enable encrypted boot for security-sensitive deployments.

RFQ Liên hệ
P1013NSE2HFB557 - QorIQ 32-Bit Power Arch SoC 800MHz | NXP/Freescale
P1013NSE2HFB557

P1013NSE2HFB557 - QorIQ 32-Bit Power Arch SoC 800MHz | NXP/Freescale

The NXP (formerly Freescale Semiconductor) P1013NSE2HFB557 is a QorIQ P1013 communications processor built on the Power Architecture technology, integrating a single e500 core running up to 800 MHz with comprehensive networking and security acceleration in a surface-mount thermally-enhanced package. It belongs to NXP's QorIQ P1 family of integrated communications processors, designed for cost-effective, high-performance networking and industrial applications. A QorIQ communications SoC (System-on-Chip) is a highly-integrated processor that combines one or more CPU cores, high-speed serial interfaces, packet processing engines, and security accelerators on a single die. Within the broader processor taxonomy, QorIQ SoCs sit between general-purpose microcontrollers and high-end multicore networking processors, optimized for deterministic throughput on packet data while retaining Linux/Power-Architecture software ecosystem compatibility. They are widely deployed in wired/wireless access equipment, industrial control, and military/aerospace embedded platforms. The P1013NSE2HFB557 provides a single 32-bit Power Architecture e500 core with MMU, dual 32-bit DDR controllers supporting DDR2/DDR3 memory, three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs), a security engine (SEC 4.0) for encryption acceleration, and a wide array of high-speed serial interfaces. The integrated QUICC Engine technology simplifies development of multi-protocol applications. The SoC targets extended-temperature and industrial-grade reliability with a robust set of peripherals including USB 2.0, PCIe, SPI, I2C, and UART controllers. Architecturally, the device combines a high-performance superscalar e500 core with hardware-based pattern matching, encryption accelerators, and DMA engines, freeing the CPU from I/O housekeeping. The combination of low power consumption, hardware virtualization support, and integrated GbE switch fabric makes it attractive for fanless industrial gateways, factory automation controllers, and secure networking appliances. The platform supports standard Linux distributions and VxWorks/RTOS environments. Typical applications include industrial Ethernet switches and gateways, factory automation controllers, secure routers and firewalls, smart-grid and substation communication equipment, defense and aerospace networking gear, automotive telematics and infotainment modules, and medical imaging or diagnostic data acquisition systems requiring deterministic networking throughput with hardware-accelerated cryptography. When designing with this device, allocate sufficient PCB area for the high-pin-count thermally-enhanced package and follow NXP hardware reference manual recommendations for DDR3 routing, decoupling, and thermal dissipation. Always verify boot configuration, JTAG chain, and SerDes reference clocking per the official reference manual before bringing up a new board. This page synthesizes distributor pricing, package metadata, and practical design context that complement the official NXP P1013 reference manual and QorIQ P1 product brief, providing engineers a fast decision-ready overview beyond what datasheets alone expose.

RFQ Liên hệ
P1013NSE2LFB - QorIQ P1 1GHz PowerPC e500v2 MPU | NXP
P1013NSE2LFB

P1013NSE2LFB - QorIQ P1 1GHz PowerPC e500v2 MPU | NXP

The NXP P1013NSE2LFB is a QorIQ P1 family PowerPC e500v2 microprocessor delivering 1.055 GHz single-core performance in a 689-TEPBGA II (31x31 mm) package. It integrates GbE, PCIe, USB, DDR2/DDR3 with ECC, SEC encryption, and LCD controller, addressing complex IP networking and advanced media processing workloads. A QorIQ communications processor is a member of the broader Power Architecture microprocessor family, itself a subset of embedded MPU (microprocessor unit) and SoC (system-on-chip) categories used in networking, industrial, and telecom infrastructure. Within that hierarchy, QorIQ P1 sits below QorIQ P2/P3 multi-core devices but above simple host-side controllers, balancing integration with deterministic single-thread performance. Key differentiating features include the e500v2 dual-issue superscalar core with signal-processing extensions, hardware-accelerated SEC (Secure Communications) engine for IPsec and SSL/TLS, integrated LCD controller for HMI panels, and dual GbE ports with QoS classification. The 32-bit core pairs with a 32-bit DDR2/DDR3 memory controller supporting ECC, and the device operates across a 0 C to 105 C commercial thermal envelope. Architecturally, the P1013 combines an e500v2 core with on-chip SRAM, a high-bandwidth interconnect fabric, and a peripheral complex combining SerDes lanes, USB 2.0, and SD/MMC interfaces. The SerDes Fabric helps achieve deterministic latency for line-rate packet processing, while maintaining low power dissipation suitable for fanless industrial gateways. Typical applications include industrial routers, factory automation controllers, single-board computers, secure VPN gateways, and fanless embedded appliances. The integrated SEC engine and GbE acceleration also suit managed switches and small-form-factor NAS devices. When designing with this device, ensure proper thermal management: the 31x31 mm TEPBGA-II package has a relatively high theta-JA, so a multi-layer PCB with thermal vias and sufficient airflow is recommended for sustained workloads above 0.7 GHz. This page synthesizes distributor pricing, pin-compatible drop-in alternatives from the QorIQ P1 family, and practical design notes that are not assembled in any single manufacturer document.

RFQ Liên hệ
P1013NSE2MHB - QorIQ P1 e500v2 1.055GHz SoC 689-TEPBGA | NXP
P1013NSE2MHB

P1013NSE2MHB - QorIQ P1 e500v2 1.055GHz SoC 689-TEPBGA | NXP

The NXP P1013NSE2MHB is a QorIQ P1 series Power Architecture SoC integrating a single e500v2 core running at up to 1.055 GHz with comprehensive networking and media peripherals, housed in a 689-ball TEPBGA II (31x31 mm) package. Headline parameters include: 1.055 GHz single-core e500v2, integrated GbE, PCIe, USB 2.0, DDR2/DDR3 memory controller with ECC, SEC security engine, and an LCD controller, all in one 689-TEPBGA package with operating temperature 0 to 105 C. The P1013NSE2MHB is the engineering-revision marking (Rev 2) variant of the P1013 family. A microprocessor MPU (Microprocessor Unit) is the central processing element of an embedded computing system. Unlike a microcontroller MCU, an MPU typically lacks on-chip flash and relies on external DDR memory for program and data storage. The P1013NSE2MHB belongs to the QorIQ P1 communications processor family, positioned between simple MCUs and full multicore application processors. It is classified within the taxonomy: SoC -> MPU -> Power Architecture -> communications processor -> NXP QorIQ P1. Key features of the P1013NSE2MHB include hardware-accelerated SEC for IPsec and SSL/TLS offload (saving CPU cycles for control-plane tasks), a DDR2/DDR3 memory controller with ECC for high-availability systems, three 10/100/1000 Ethernet MACs with integrated PHYs or SerDes interfaces, multiple PCIe Gen1 lanes, USB 2.0 host/device, and an integrated LCD controller for HMI panels. The die revision (Rev 2) provides silicon errata fixes relative to Rev 1. Architecturally the P1013NSE2MHB pairs the e500v2 superscalar core with a high-bandwidth system bus interconnect to peripherals, a DPAA-lite style acceleration fabric, and dedicated engine blocks (SEC, PME). The advanced power-management features support dynamic frequency scaling and deep sleep modes, enabling fanless operation in thermally constrained networking appliances. Typical applications include industrial gateway routers, smart-grid substation controllers, factory automation PLCs, HMI panels, single-board computers for IP-PBX and Unified Threat Management appliances, and networked industrial printers. The integrated GbE and SEC make it well suited for VPN and firewall line cards in SMB and branch-office networking equipment. A core design consideration is the BGA package complexity - the 689-TEPBGA II (31x31 mm) requires multi-layer PCB with microvia or via-in-pad stackup, controlled-impedance routing for DDR3 and SerDes, and reflow oven with fine-pitch BGA capability; ensure a minimum 8-layer stackup with continuous ground planes under the BGA. This page combines distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Liên hệ
P1013NSE2MHB557 - QorIQ P1013 e500v2 MPU 1.2GHz 689-TEPBGA II | NXP
P1013NSE2MHB557

P1013NSE2MHB557 - QorIQ P1013 e500v2 MPU 1.2GHz 689-TEPBGA II | NXP

The NXP P1013NSE2MHB557 is a high-performance PowerPC e500v2 microprocessor from the QorIQ P1 family, featuring a single 32-bit core running at 1.2 GHz, housed in a 689-ball TEPBGA II (31x31 mm) package. It is part of NXP's communications-processor portfolio, integrating dual Gigabit Ethernet MACs, three 10/100/1000 Ethernet controllers, DDR2/DDR3 memory controller, PCI Express, and security acceleration for IP networking and industrial control applications. A QorIQ P1013 device is a 32-bit embedded communications processor built on Power Architecture technology, designed for low-power, highly integrated networking and industrial applications. It sits within the QorIQ P1 series, which targets branch-office routers, Ethernet switches, protocol converters, and motion-control/industrial automation, where deterministic performance, security acceleration, and high-speed connectivity (PCIe, GbE, SerDes) are required. Within NXP's hierarchy it falls under communications processors -> PowerQUICC/QorIQ -> Power Architecture -> embedded microprocessor. Key specifications include a 32-bit e500v2 core with integrated double-precision floating-point unit, 32 KB I-cache and 32 KB D-cache, 32-bit DDR2/DDR3 memory controller with ECC running up to 800 MHz data rate, three enhanced 10/100/1000 Ethernet MACs, two PCI Express endpoints/RCs, USB 2.0, SD/MMC, SPI, I2C, UART, DMA, and 1.0 GHz SerDes lanes for high-speed interconnect. The e500v2 core includes hardware security acceleration for symmetric (AES, 3DES, RC4) and asymmetric (RSA, ECC) cryptography, plus packet processing accelerators for IPsec, SSL/TLS, and IEEE 1588 hardware timestamping. The 689-TEPBGA II (31x31 mm) package has a thermal resistance of approximately 16 C/W with proper PCB stack-up, enabling operation in industrial temperature ranges. Typical applications include branch-office routers, Ethernet industrial switches, protocol-conversion gateways, networked motion controllers, secure VPN/SSL appliances, and IEC-61850 smart-grid controllers. The combination of GbE, PCIe, and security hardware offload enables line-rate encrypted traffic processing without an external coprocessor. When designing with the P1013NSE2MHB557, ensure the 31x31 mm TEPBGA-II land pattern uses a 12-layer PCB stack-up with matched impedance for DDR2/DDR3 routes, decoupling capacitors directly under the BGA, and adequate thermal vias. The boot ROM configuration must be set up before reset release, and system designers should consult the QorIQ P1013 reference manual. This page synthesizes distributor pricing from LCSC, DigiKey, Mouser and JLCPCB, plus drop-in QorIQ P1 family alternatives, BGA layout guidelines, and practical design notes not found condensed on the manufacturer datasheet alone.

RFQ Liên hệ
P1013NSN2LFB - QorIQ P1 1-Core 1GHz PowerPC MPU | NXP | TEPBGA-689
P1013NSN2LFB

P1013NSN2LFB - QorIQ P1 1-Core 1GHz PowerPC MPU | NXP | TEPBGA-689

The NXP P1013NSN2LFB is a single-core PowerPC e500v2 microprocessor in NXP's QorIQ P1 communications processor family, housed in a 689-pin TEPBGA II (31x31 mm) package. It integrates one e500v2 core running up to 1067 MHz with 32-bit Power Architecture technology, hardware floating-point and signal-processing engines, DDR2/DDR3 memory controller with ECC, three 10/100/1000 Mb/s Ethernet MACs (one RGMII, two SGMII), two PCIe controllers, USB 2.0, and an LCD controller. The 'N' in the part number indicates the 0 to 105 °C commercial temperature grade, and the '2' suffix indicates silicon revision 2. A microprocessor (MPU) is an integrated circuit that contains one or more central processing units, cache memory, and on-chip peripherals in a single package. The QorIQ P1 family targets cost-sensitive networking, industrial HMI, and single-board computing applications where deterministic performance, multi-protocol I/O, and long-life-cycle support matter more than raw clock speed. Within NXP's product hierarchy, the P1 sits below the dual-core P1022 and above the lower-frequency P1010/P1011 variants. Key features include three Gigabit Ethernet controllers with IEEE 1588 timestamping support, two PCIe Gen 1/2 lanes for ASIC/FPGA co-processing, a 32-bit DDR2/DDR3 memory controller with ECC for reliability-critical firmware, dedicated security acceleration (SEC 4.x with DES/3DES/AES/SHA/RSA), and integrated LCD controller for human-machine interface panels. The device supports boot from NAND/NOR flash, SPI EEPROM, and SD/MMC, simplifying secure firmware bring-up. Architecturally, the P1013NSN2LFB combines the e500v2 integer/floating-point pipeline with a 256 KB L2 cache, an on-chip core complex bus, and a platform-side enhanced local bus plus serialized I/O. The memory controller drives DDR2/DDR3 at up to 800 MT/s with ECC scrubbing, and the SerDes block multiplexes PCIe, SGMII, and SATA interfaces. Typical applications include industrial routers and gateways, factory-floor protocol converters, single-board computers for HMI, multi-protocol serial concentrators, and secure network-attached appliances. The wide peripheral mix makes the P1 well suited as a system-on-chip in cost-optimized embedded designs where a Linux or RTOS stack is acceptable. Design consideration: routing the 689-ball TEPBGA II requires a 6+ layer PCB with matched-length SerDes traces; engineers should reference the NXP hardware design guide for DDR3 topology and the PCIe/SGMIB reference impedances. Industrial applications benefit from the 0 to 105 °C operating range without needing the -40 to +125 °C 'Extended' grade. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ Liên hệ
P1013NXE2LFB - 1.067GHz e500v2 QorIQ MPU | NXP | Networking SoC
P1013NXE2LFB

P1013NXE2LFB - 1.067GHz e500v2 QorIQ MPU | NXP | Networking SoC

The NXP P1013NXE2LFB is a PowerPC e500v2 based QorIQ P1 series microprocessor integrating a single 32-bit core running up to 1.067 GHz with 256 KB of L2 cache, packaged in a 689-ball TEPBGA II (31x31 mm) for industrial and networking applications. The device combines an embedded Power Architecture core with on-chip peripherals that include DDR2/DDR3 memory controller with ECC, three 10/100/1000 Ethernet MACs (with one supporting 2.5 G SGMII), four PCI Express controllers, two USB 2.0 interfaces, a SEC security engine, an LCD controller, and FlexCAN for automotive/industrial networking. Target operating temperature range is -40C to +125C, reflecting the part's industrial/automotive focus. What is an MPU SoC? An MPU (Microprocessor Unit) System-on-Chip integrates a CPU core, memory controllers, and a wide range of peripherals (Ethernet, PCIe, USB, security blocks) onto a single die. Within the NXP QorIQ P1 family it sits in the hierarchical chain: e500v2 core -> PowerPC core -> Power Architecture MPU -> communications processor -> embedded SoC. This level of integration reduces board area, BOM cost, and design complexity for routers, switches, and industrial gateways that previously required a CPU plus a multi-chip peripheral set. Key features include hardware-accelerated IPSec/SEC, a 32-bit DDR2/DDR3 controller with ECC, integrated LCD display controller up to 1280x1024, four PCI Express lanes, three Gigabit Ethernet MACs (one configurable as 2.5G), FlexCAN 2.0, dual USB 2.0 with PHY, and a True Hardware Random Number Generator. Industrial peripherals include two I2C, two UART, two SPI, and an SD/MMC interface. The P1013NXE2LFB uses the e500v2 superscalar core with dual integer and dual floating-point (single-precision) units, BTB and 16 KB/16 KB instruction/data L1 caches, and a 256 KB backend L2. The platform integrates a high-bandwidth interconnect plus dedicated DMA channels to sustain throughput on Ethernet and PCIe paths while keeping interrupt latency bounded. According to the NXP product page, the device is marked End of Life and is targeted for replacement by the Layerscape LS1021A family. Typical applications include industrial routers, factory-floor gateways, networked HMI panels, single-board computers, secure access points, CAN-bridge automation controllers, and SMB network attached storage. Its wide -40C to +125C temperature range and integrated peripherals make it suited for harsh-environment networking equipment and automotive telematics ECUs. Designers should plan for a multi-layer PCB with controlled-impedance DDR3 routing, a 5 mm keep-out around the 31x31 mm BGA, and bulk decoupling sized for the simultaneous switching of PCIe and SerDes I/O. For new designs, evaluate the Layerscape LS1021A as the recommended drop-in successor. This page synthesizes distributor stock, lifecycle status, pin-compatible QorIQ alternatives, and practical board-design notes that supplement the manufacturer datasheet and the NXP end-of-life notice.

RFQ Liên hệ
P1013NXN2LFB - QorIQ P1022 Power Arch SoC 1GHz | NXP
P1013NXN2LFB

P1013NXN2LFB - QorIQ P1022 Power Arch SoC 1GHz | NXP

The NXP P1013NXN2LFB is a QorIQ P1022-family Power Architecture system-on-chip integrating a single 32-bit e500v2 core running at up to 1.067 GHz, with hardware-accelerated networking, security, and DDR2/DDR3 memory controller. The part is housed in a 689-ball TEPBGA II (31 mm x 31 mm) package and is rated for the extended -40C to +125C industrial/automotive junction temperature range. QorIQ P1 series SoCs belong to the Power Architecture (PowerPC) family of integrated communications processors, sitting in the taxonomy: QorIQ P1022 -> Power Architecture SoC -> communications processor -> microprocessor -> integrated circuit. The e500v2 core executes the Power ISA with double-precision FPU, MMU, and a 32 KB instruction / 32 KB data L1 cache per core, plus a coherent 256 KB L2 platform cache. Key features include a 64-bit DDR2/DDR3 memory controller with ECC, three 10/100/1000 Ethernet MACs (two via SGMII/HS SerDes, one RGMII), two PCI Express Gen 1.1 controllers (x4/x1), one USB 2.0 with PHY, an enhanced local bus, eSDHC, eSPI, I2C, UARTs, and an LCD controller. The device is built on a 45 nm SOI process with low-power idle, dynamic frequency switching, and deep-sleep modes for fan-less embedded systems. Typical applications include industrial control and factory automation, secure networking appliances, IP gateways, LTE/small-cell baseband, smart-grid gateways, networked printers, and automotive telematics/ECUs. The wide temperature range and ECC memory make P1013NXN2LFB especially suited to harsh-environment and long-life industrial designs. When designing with P1013NXN2LFB, follow NXP hardware-reference-manual layout guidelines: place the DDR3 channel as close as possible with matched trace lengths, and provide adequate bulk decoupling on the 1.0 V core and 1.5 V/1.8 V/2.5 V/3.3 V I/O rails. Use JTAG/cOP boundary-scan for first-board bring-up. This page synthesizes distributor pricing, drop-in alternatives from the same NXP QorIQ P1/P1022 family, and practical board-design notes that complement the official NXP hardware reference manual.

RFQ Liên hệ
P1014NSE5DFA - QorIQ P1014 533MHz Power Arch SoC | NXP
P1014NSE5DFA

P1014NSE5DFA - QorIQ P1014 533MHz Power Arch SoC | NXP

The NXP P1014NSE5DFA is a QorIQ P1014 communications processor, a 32-bit Power Architecture system-on-chip (SoC) featuring a single e500v2 core running at up to 533 MHz, integrated into a 425-ball TEPBGA-1 package (FBGA form factor, square package, ball grid array). The device integrates Gigabit Ethernet, SATA, USB 2.0, PCIe, DDR3 memory controller, and a security engine (SEC) for cost- and power-sensitive networking and industrial applications. A communications processor is a specialized SoC that combines application processing, packet handling, and peripheral I/O on a single die, targeting networking equipment such as entry-level routers, industrial gateways, and protocol bridges. The QorIQ P1 series, of which the P1014 is a member, sits at the lower end of the QorIQ family—below the P2/P3 multi-core SoCs—optimized for fanless and thermally constrained designs that still require deterministic packet processing and hardware-accelerated security. Key features include the e500v2 core with dual-issue superscalar execution, integrated SEC security engine supporting DES, AES, RSA, and ECC acceleration, dual GbE controllers with L2 switching, SATA 1.5/3.0 Gb/s, USB 2.0 host/device, one PCIe Gen 1 lane, and a 32-bit DDR3 memory controller with ECC support. Per the NXP product page, the P1010/P1014 family expands QorIQ performance into cost- and power-sensitive segments while maintaining pin-software compatibility with the broader P1 series. Typical applications include entry-level industrial routers, smart grid gateways, networked printers, factory automation controllers, and HVAC/networked building controllers. The integrated GbE and SEC make the P1014NSE5DFA particularly suitable for secure remote-management equipment such as VPN concentrators and protocol-translation gateways. The 425-ball TEPBGA-1 package requires multi-layer PCB design with controlled-impedance routing; designers should follow NXP's hardware design guide for the QorIQ P1010/P1014 reference design. When designing with the P1014NSE5DFA, ensure the DDR3 interface uses matched-length traces and proper termination; the SEC engine requires an entropy source for true-random-number generation; and the operating junction temperature must stay within the 0°C to 105°C ambient range. The NXP CodeWarrior and Linux BSP toolchains provide full debug and production support for this SoC. This page synthesizes distributor inventory, drop-in alternatives from the QorIQ P1 family, and practical design notes not found in the manufacturer datasheet, helping engineers select the correct variant for their networking and industrial application.

RFQ Liên hệ
P1014NSE5FFA - QorIQ P1014 800MHz e500v2 MPU 425-TEPBGA | NXP
P1014NSE5FFA

P1014NSE5FFA - QorIQ P1014 800MHz e500v2 MPU 425-TEPBGA | NXP

The NXP P1014NSE5FFA is a QorIQ P1014 communications processor built on the Power Architecture e500v2 core, integrating one 32-bit core running at 800 MHz in a 425-ball TEPBGA package. It combines a high-performance CPU subsystem with hardware accelerators for security (SEC), pattern matching, and fast-path networking, making it a single-chip SoC for cost- and power-sensitive embedded networking equipment. The device targets industrial temperature grade (0C to 105C operating junction range) and is RoHS compliant with lead-free solder-ball terminations. A communications processor is a specialized system-on-chip that combines one or more CPU cores with integrated peripherals and on-chip accelerators designed for networking infrastructure. The QorIQ family evolved from Freescale's (now NXP) PowerQUICC line, adding high-speed interfaces (USB, SATA, GbE, PCIe) and DDR3 memory controllers while keeping power consumption low. The P1014 sits in the entry-tier QorIQ P1 family alongside the P1010, balancing compute headroom with low power for fanless designs. Key specifications include a 32-bit e500v2 core at 800 MHz, integrated SEC 4.x crypto engine, three 10/100/1000 Ethernet MACs (one RGMII + two SGMII), three PCIe Gen2 controllers, one USB 2.0 controller, one SATA 2.0 controller, and a 32-bit DDR3 memory controller with ECC. Memory interfaces include a 16-bit local bus and IFC for NAND/NOR flash. The 425-TEPBGA is a 19 mm x 19 mm fine-pitch wire-bond BGA designed for multilayer PCB stacks with low-impedance power delivery. Typical applications include industrial gateways, factory-floor protocol converters, smart-grid energy routers, small-cell base stations, network-attached storage controllers, and IoT edge appliances requiring deterministic networking with hardware crypto offload. The SEC engine accelerates IPsec, SSL/TLS, and MACsec without burdening the e500 core. Design considerations include careful power-rail sequencing (core and I/O domains are separate), thermal management through the package's center thermal balls, and impedance-controlled PCB stackup for DDR3, RGMII, and SGMII signaling. A board-level reference design from NXP's QorIQ development platform is recommended as a starting layout.

RFQ Liên hệ
P1014NSE5FFA557 - QorIQ P1014 800MHz e500 SoC | NXP
P1014NSE5FFA557

P1014NSE5FFA557 - QorIQ P1014 800MHz e500 SoC | NXP

The NXP P1014NSE5FFA557 is a QorIQ communications processor built on the 32-bit Power Architecture e500 core, integrating a single core up to 800 MHz with DDR3 memory controller, three PCI Express controllers, SATA, USB and a security engine. The device is housed in a 425-ball FCBGA (NSE) package and is rated for the 0 to 105 degrees C extended industrial temperature range. The suffix 557 denotes the standard NXP tray packaging option, and the FFA suffix indicates the integrated security (SEC) engine variant within the P1014 family. A QorIQ communications processor is a high-performance SoC designed for wired and wireless networking applications where deterministic throughput, packet processing acceleration and security offload are required. QorIQ platforms sit within the broader NXP communications processor taxonomy, descending from PowerQUICC and ascending into the broader categories of embedded microprocessor and networking SoC. The QorIQ P1 family targets cost- and power-sensitive applications while maintaining hardware-level encryption, virtualization and multi-protocol support. Key features of the P1014NSE5FFA557 include 800 MHz e500 core speed, integrated SEC 4.x crypto engine for IPSec, SSL/TLS and 3GPP algorithms, three PCI Express Gen 1.1 controllers, two SATA 2.0 interfaces, two USB 2.0 controllers (host + device or dual-host), dual 10/100/1000 Mb/s Ethernet MACs, 32-bit DDR3 memory controller with ECC support, and 32-bit local bus. The security engine and packet processing acceleration offload tasks from the host CPU, enabling line-rate performance on networking data planes. Typical applications for the P1014NSE5FFA557 include industrial routers, secure gateways, factory automation controllers, network-attached storage (NAS), single-board computing platforms, and embedded IoT edge nodes. The wide industrial temperature range and integrated security make it particularly suitable for industrial Ethernet switches and protocol-conversion gateways operating in harsh environments where deterministic throughput is required.

RFQ Liên hệ
P1014NSE5HFA - QorIQ P1014 800MHz Power Arch SoC | NXP
P1014NSE5HFA

P1014NSE5HFA - QorIQ P1014 800MHz Power Arch SoC | NXP

The NXP (formerly Freescale) P1014NSE5HFA is a QorIQ P1014 communications processor that integrates a 32-bit Power Architecture e500v2 core running at 800 MHz with a rich set of communications peripherals in a 425-pin TEBGA-1 package. It is a member of the QorIQ P1 family designed for cost- and power-sensitive networking applications, with 0 to 105C industrial temperature support. A QorIQ communications processor is a system-on-chip (SoC) that combines one or more Power Architecture CPU cores with high-speed serial interfaces, memory controllers, security engines, and packet processing acceleration in a single device. It belongs to the broader category of microprocessors (MPUs) and embedded SoCs, sitting in the hierarchy: SoC -> MPU -> communications processor -> networking SoC. The QorIQ family evolved from Freescale's PowerQUICC line and targets routers, switches, and industrial gateways. Key features of the P1014NSE5HFA include an 800 MHz e500v2 core with 32 KB L1 instruction cache and 32 KB L1 data cache, a 256 KB L2 cache, integrated SEC security engine for cryptographic acceleration, three PCI Express Gen 1 controllers, two SATA 2.0 ports, two USB 2.0 controllers (host + device/host), dual Gigabit Ethernet MACs (SGMII), and a DDR3 SDRAM memory controller with ECC support. The device operates from a typical 1.0V core supply and 1.5/1.8V DDR3 supply. The architecture uses a 45 nm process technology and integrates a high-bandwidth interconnect fabric to sustain line-rate packet processing across the GbE, SATA, USB, and PCIe interfaces simultaneously. The on-chip SEC engine accelerates AES, DES/3DES, RSA, and ECC operations, offloading security from the CPU and enabling VPN, IPsec, and TLS termination at line rate. Typical applications include industrial routers and gateways, secure access points, networked embedded control, factory automation controllers, smart-grid endpoints, and small-form-factor networking appliances. The combination of GbE + USB + SATA + PCIe in a single SoC allows compact BOM designs without external bridges. When designing with this part, follow NXP hardware design guidelines for the 425-pin TEBGA-1 land pattern; ensure the DDR3 controller reference resistor values match the chosen SO-DIMM or discrete DRAM topology, and respect the layout constraints for the SGMII SerDes lanes to meet jitter margins. This page synthesizes distributor pricing, drop-in QorIQ P1 family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Liên hệ
P1014NSE5HFA557 - QorIQ P1 800MHz e500v2 MPU | NXP
P1014NSE5HFA557

P1014NSE5HFA557 - QorIQ P1 800MHz e500v2 MPU | NXP

The NXP (formerly Freescale) P1014NSE5HFA557 is a QorIQ P1 series communications microprocessor featuring a single 32-bit Power Architecture e500v2 core running up to 800 MHz, integrated in a 425-terminal TE-PBGA (425-TEPBGA1) package with 0.80 mm ball pitch. The P1014 family targets cost-sensitive, power-efficient embedded networking and industrial control applications where deterministic processing, low thermal dissipation, and a compact BGA footprint are required. A QorIQ communications processor is a 32-bit Power Architecture system-on-chip (SoC) that integrates one or more e500 cores with networking peripherals, DDR memory controllers, and high-speed serial interfaces. The P1014 belongs to the broader Power Architecture (PowerPC) communications processor family, sitting below the multi-core P2/P3/QorIQ lines and above the simpler PowerQUICC II devices. Compared to general-purpose microcontrollers, a QorIQ part delivers integrated Ethernet MACs, security acceleration, and large DDR2/DDR3 support, enabling it to replace external components in router, gateway, and factory-floor designs. Key features of the P1014 include a single e500v2 core with 32 KB instruction and 32 KB data L1 caches, a 256 KB unified L2 cache with ECC, dual 10/100/1000 Mbps Ethernet MACs, DDR2/DDR3 memory controller with ECC, PCI Express and SATA interfaces, USB 2.0, and integrated security engines for IPSec, SSL/TLS, and bulk data encryption. The 557 designator encodes the specific speed grade (800 MHz core / 667 MHz platform) and operating temperature range per NXP's product naming convention. Typical applications include industrial Ethernet gateways, substation routers and protocol converters, small-form-factor NAS/SAN appliances, factory-floor controllers with deterministic networking, and secure VPN concentrators. The combination of low power consumption, integrated peripherals, and Power Architecture software compatibility makes the P1014 attractive for long-lifecycle embedded designs. When designing with the P1014NSE5HFA557, ensure the PCB land pattern follows NXP's 425-TEPBGA1 footprint (0.80 mm pitch). Use at least 4-layer PCB construction with continuous ground planes for signal integrity on DDR traces, and provide adequate thermal vias beneath the BGA die for heat extraction. Software support is available through NXP's CodeWarrior, Linux BSP, and VxWorks distributions.

RFQ Liên hệ
P1014NSE5HHA - QorIQ P1014 SoC, 800 MHz e500, 425-TEPBGA | NXP
P1014NSE5HHA

P1014NSE5HHA - QorIQ P1014 SoC, 800 MHz e500, 425-TEPBGA | NXP

The NXP (formerly Freescale) P1014NSE5HHA is a QorIQ P1014 communications processor built on the Power Architecture e500v2 core, delivering up to 800 MHz operation in a 425-ball TEPBGA (19x19 mm) package. It integrates a single 32-bit Power Architecture core with on-chip SEC security engine, dual GbE controllers, three PCIe controllers, two SATA ports, two USB 2.0 ports (host + device), and a 16-bit DDR3 memory controller, providing a complete system-on-chip (SoC) for cost- and power-sensitive networking. A QorIQ communications processor is a category of Power Architecture-based SoCs designed by NXP/Freescale to consolidate networking, security, and I/O functions that previously required separate components. Within the broader taxonomy, the P1014 sits in the entry tier of the QorIQ P1 family, between the lower-frequency P1010 and the higher-end P1020 dual-core parts, and is built on a 45 nm CMOS process for low static and dynamic power. Key features include 800 MHz core frequency, integrated SEC 4.0 cryptographic accelerator, hardware pattern-matching and queuing engines, dual 10/100/1000 Ethernet MACs with SGMII support, three PCI Express Gen 1 controllers, two SATA Gen 2 interfaces, USB 2.0 host and device, 16-bit DDR3 with ECC up to 800 MT/s, and an operating temperature range of 0°C to 105°C suitable for thermally managed industrial enclosures. The integrated SEC engine offloads IPSec, SSL/TLS, and bulk encryption from the core, while the queue manager and pattern-matching blocks accelerate deep-packet inspection workloads without external TCAMs. The P1014NSE5HHA is intended for industrial-grade networking equipment where the SoC must combine cryptographic acceleration, multiple high-speed I/Os, and DDR3 memory in a single 425-ball 19x19 mm BGA footprint. Typical applications include small-form-factor industrial routers, secure edge gateways, industrial IoT gateways, networked storage controllers (NAS/SAN), factory automation controllers, and compact wireless backhaul equipment. When designing with this device, allocate the DDR3 fly-by routing carefully to maintain signal integrity at 800 MT/s, place at least one 100 nF decoupling capacitor per power pin pair adjacent to the BGA, and verify thermal headroom with the manufacturer-provided junction-to-ambient and junction-to-case thermal resistance values for the 425-TEPBGA package. Use NXP's CodeWarrior or QorIQ Linux SDK for software development, and consult the reference design guide for the SERDES reference clocking and PCIe reference clock distribution topology.

RFQ Liên hệ
P1014NSN5DFA - QorIQ P1014 e500v2 SoC 800MHz | NXP Semiconductors
P1014NSN5DFA

P1014NSN5DFA - QorIQ P1014 e500v2 SoC 800MHz | NXP Semiconductors

The NXP Semiconductors (formerly Freescale) P1014NSN5DFA is a QorIQ P1014 communications processor built on the Power Architecture e500v2 core, integrating GbE, USB, SATA, and PCIe connectivity into a single 425-ball TEPBGA I (19x19 mm) package. It runs up to 800 MHz and is qualified for industrial operating conditions from 0C to 105C. A communications processor is a system-on-chip (SoC) that combines a CPU core, memory controller, and multiple high-speed IO peripherals on a single die; it is the next-generation evolution of the PowerQUICC series and is part of NXP's QorIQ P1 family. Within the system hierarchy, the P1014 sits between general-purpose microcontrollers and high-end networking SoCs, targeting cost- and power-sensitive applications such as SOHO routers and industrial gateways. The same family tree also includes the lower-speed P1010 variant (up to 533 MHz), letting designers scale performance within a pin-compatible footprint. Key features include a 32-bit Power Architecture e500v2 core with dual-issue superscalar execution, a 32/16-bit DDR3 memory controller with ECC support, two Gigabit Ethernet MACs (one RGMII, one SGMII capable), two USB 2.0 controllers (host + device/host), two SATA 2.0 ports at 3 Gb/s, and one PCIe x4 Gen 2 controller. Integrated security includes basic secure-boot and Trust Architecture support typical of the P1 family. The device integrates the SerDes, networking, and IO IP that historically required companion chipsets in PowerQUICC designs, reducing PCB area, BOM count, and design complexity. Power is supplied through multiple rails including 1.0V core and 1.5V/1.8V DDR, with power management controlled by on-chip PLLs. Typical applications include SOHO/SMB routers, wireless LAN access points, industrial automation controllers, networked printers, IP cameras/NVR, and smart-grid gateway nodes. The industrial-grade temperature range and integrated networking make it especially well suited to harsh-environment edge appliances. When designing with this part, ensure the DDR3 routing meets the controller's impedance and length-matching rules and that the SerDes reference clock is clean, because signal-integrity violations here degrade GbE and PCIe link margin. The 425-ball TEPBGA requires standard 0.8 mm-pitch PCB rules plus microvia or laser-drill capability. This page synthesizes distributor pricing, drop-in alternatives drawn from the same P1 family, and practical design notes that complement rather than duplicate the manufacturer datasheet.

RFQ Liên hệ
P1014NSN5DFA557 - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP
P1014NSN5DFA557

P1014NSN5DFA557 - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP

The NXP P1014NSN5DFA557 is a PowerPC e500v2 microprocessor in NXP's QorIQ P1 family with a single 32-bit core running at 800 MHz, housed in a 425-ball TEPBGA package (19 x 19 mm). It integrates 256 KB of L2 cache with ECC, 32 KB of instruction and 32 KB of data L1 cache per core, and 64-bit DDR3 memory controller with ECC support, making it well suited for low-power, deterministic networking and control plane workloads. What is a QorIQ communications processor? QorIQ is a NXP semiconductor family that sits in the broader taxonomy of microprocessors (MPU) and embedded processors, which are higher-performance than microcontrollers (MCU) and are typically deployed as the central compute node in routers, switches, and access gateways. The P1 series is the lower-power tier of QorIQ, sharing software compatibility with the higher-end P2/P3/P4 families via the standard PowerPC e500v2 instruction set, Book-E programming model, and common peripherals. The P1014 specifically targets fanless and thermally constrained designs that still require multi-gigabit packet processing. The P1014NSN5DFA557 supports a single 533/667/800 MHz core speed bin, dual 10/100/1000 Mbps Ethernet controllers (eTSEC), PCIe Gen1/Gen2, and up to 32-bit DDR3 with ECC at up to 800 MHz. A hardware encryption block accelerates AES, DES, 3DES, SHA-1/256, and public-key algorithms, with secure boot supported through the on-chip secure boot extension. Interface flexibility is provided through USB 2.0, SD/MMC, two I2C controllers, and four UARTs. Low-power standby modes reduce idle consumption to a fraction of the active budget. Typical applications include SOHO/SMB routers, wireless LAN access points, smart grid gateways, factory-floor protocol bridges, and industrial IoT edge nodes. NXP also positions P1014 derivatives for networked printers, IP cameras, and HVAC controllers where deterministic real-time response is required. When designing with the P1014, plan 4-layer PCB stack-up with controlled-impedance routing for DDR3; allocate 1.0 V core (min 0.95 V, max 1.05 V) and 1.5 V DDR3 supplies with bulk decoupling within 50 mm of the BGA. Total power at 800 MHz typically stays below 3.5 W, allowing passive heatsinking. This page consolidates cross-brand positioning context, drop-in same-family replacement guidance, and design notes not found in the standalone datasheet PDF.

RFQ Liên hệ
P1014NSN5HFA - QorIQ P1014 800MHz SoC, DDR3, GbE | NXP
P1014NSN5HFA

P1014NSN5HFA - QorIQ P1014 800MHz SoC, DDR3, GbE | NXP

The NXP P1014NSN5HFA is a QorIQ P1 communications processor SoC featuring a single 32-bit Power Architecture e500v2 core running at 800 MHz, integrating USB 2.0, SATA, Gigabit Ethernet, PCIe, and DDR3 memory controller in a 425-ball TEPBGA I (19x19 mm) package. It is positioned as the higher-speed, higher-cache sibling of the P1010 family, expanding QorIQ performance into cost- and power-sensitive networking applications such as industrial control, factory automation, and entry-level network appliances. What is a QorIQ communications processor? QorIQ is NXP's Power Architecture-based system-on-chip (SoC) platform for networking and industrial embedded applications, sitting in the hierarchy of: SoC -> communications processor -> microprocessor (MPU). It integrates CPU cores with networking peripherals (Ethernet, PCIe, SATA, USB), a memory controller, and security engines on a single die, replacing multi-chip designs with one part. QorIQ P1 series targets low-power, single-core applications where cost and deterministic performance matter more than multi-core throughput. Key features of the P1014NSN5HFA include a single Power Architecture e500v2 core at 800 MHz, integrated DDR3 memory controller with ECC support, three Gigabit Ethernet interfaces (one with packet parsing acceleration), two PCIe Gen1 controllers, two SATA 2.0 ports, USB 2.0 host/device, and a security engine for IPsec, SSL/TLS, and trusted boot. The device supports an operating temperature range of 0C to 105C, enabling deployment in thermally demanding industrial enclosures without additional cooling. The P1014 architecture implements a 32-bit superscalar e500v2 core with hardware virtualization and signal-processing extensions. Its on-die packet processing engine accelerates routing and filtering tasks, offloading work from the core and reducing latency for time-sensitive network traffic. The integrated security engine handles AES, 3DES, and SHA acceleration, enabling VPN termination and secure boot without external crypto chips. Typical applications for the P1014NSN5HFA include industrial Ethernet gateways, factory automation controllers, smart grid substation equipment, entry-level routers and switches, network-attached storage controllers, and embedded control boards in railway and energy systems. Its combination of networking peripherals and a deterministic real-time capable core makes it especially suitable for protocol conversion gateways that bridge Modbus, EtherCAT, or PROFINET with enterprise networks. When designing with this device, allocate at least 8 PCB layers with dedicated ground and power planes, and follow NXP AN4160 layout guidance for the DDR3 controller. The device supports a wide range of boot sources including NOR flash, NAND flash, SPI, and SD/MMC, simplifying firmware development. JTAG and Aurora debug interfaces are available for boundary-scan and trace-based debugging. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P1 family, and practical design notes not found in the manufacturer datasheet.

RFQ Liên hệ
P1014NSN5HFA557 - QorIQ 32-bit Power Arch SoC 800MHz | NXP
P1014NSN5HFA557

P1014NSN5HFA557 - QorIQ 32-bit Power Arch SoC 800MHz | NXP

The NXP P1014NSN5HFA557 is a QorIQ 32-bit Power Architecture system-on-chip (SoC) communications processor operating at up to 800 MHz core frequency with a 667 MHz DDR3 memory controller, housed in a 425-ball, 0.8 mm pitch PBGA package measuring 19 x 19 mm. Built on 45 nm low-power CMOS technology, the P1014 integrates a single e500 core with 32 KB I-cache and 32 KB D-cache, hardware ECC-protected DDR3/3L memory controller, dual GbE controllers, three PCIe Gen 1.1 controllers, two SATA 2.0 ports, USB 2.0 (host/device/OTG), and integrated security engine with trusted boot and secure debug. A QorIQ communications processor is a multicore Power Architecture SoC designed for cost- and power-sensitive networking, industrial control, and secure gateway applications. Within the broader NXP product hierarchy, the P1010/P1014 family sits below the high-end P2020/P2040 dual-core devices and above the value-tier P1010/P1013 single-core parts, occupying the integrated-networking sub-segment of the Power Architecture communications processor roadmap. Key differentiating features of the P1014 include hardware-accelerated protocol handling for packet processing, integrated SERDES lanes that eliminate external PHYs for GbE/SATA/PCIe, and a flexible SerDes configuration supporting up to 5 lanes. The device operates from a single 1.0 V nominal core supply (range 0.95 V to 1.05 V) with separate I/O and PLL rails, supporting commercial 0 C to +105 C junction temperature. Typical applications include industrial IoT gateways, factory automation controllers, secure network appliances, fanless embedded routers, and smart-grid infrastructure. The integrated security engine and Trust Architecture support tamper-resistant firmware boot, while the low 4 W typical power envelope enables fanless designs in compact enclosures. When designing with the P1014, allocate adequate decoupling on every 1.0 V rail and provide a 25 MHz reference clock into the differential SYSCLK pins. Route all high-speed SERDES lanes with controlled-impedance 85 ohm differential pairs and follow the NXP reference board stack-up to maintain signal-integrity margins. This page synthesizes octopart distributor pricing, octopart cross-reference listings, and practical design notes for the P1014NSN5HFA557, complementing the manufacturer datasheet with engineering insight not found on stock pages.

RFQ Liên hệ