積體電路

PIC18F45Q10-I/P

PIC18F45Q10-I/P - 32KB Flash 8-bit MCU 64MHz 40-PDIP | Microchip

The Microchip Technology PIC18F45Q10-I/P is a 32KB Flash, 8-bit PIC18 XLP microcontroller running up to 64 MHz in a 40-pin PDIP through-hole package. It integrates 2KB SRAM, 1KB EEPROM, 5V operation for noise immunity, intelligent analog peripherals, and Functional Safety (FuSa) capability for safety-critical systems. The PIC18F45Q10 belongs to the PIC18 family of 8-bit microcontrollers (MCUs) within Microchip's broader PIC® architecture hierarchy. An 8-bit MCU executes instructions on 8-bit data paths and is the workhorse of embedded control for cost-sensitive, deterministic real-time applications. PIC18 devices extend the baseline and mid-range PIC cores with 16-bit instructions, hardware multiplier, and C-optimized architecture, enabling efficient high-level language development while retaining deterministic interrupt response. Key features of this part include a 64 MHz internal oscillator, up to 64 MHz CPU clock with 4x PLL option, 35 instruction set, 10-bit ADC with Computation (ADCC) automating averaging and threshold comparison, 5-bit DAC, 2 analog comparators with selectable hysteresis, Configurable Logic Cells (CLC) for hardware state-machine peripherals, Complementary Waveform Generator (CWG), and Peripheral Pin Select (PPS) for flexible signal routing. Functional Safety (FuSa) diagnostics make it suitable for IEC 61508 SIL-2 capable designs when used with the supporting FMEDA and diagnostic libraries. Typical applications include industrial sensor nodes, household appliances, motor control, lighting ballasts, IoT edge nodes, automotive body and chassis subsystems, HVAC controllers, and any real-time control loop where deterministic behavior, low power, and 5V noise immunity are required. The 32KB Flash supports moderate firmware footprints typical of connected sensor firmware with protocol stacks. When designing with this device, allocate sufficient decoupling (100 nF + 1 µF near each supply pin), use the ICSP™ header for in-circuit programming, and follow Microchip AN1255 for Class B / IEC 60730 safety diagnostics on white goods. The wide 2.3V-5.5V VDD range supports both 3.3V and 5V systems, but power-on reset thresholds differ at each range.

詢價聯絡我們

PIC18F45Q10-I/PT

PIC18F45Q10-I/PT - 32KB Flash 8-bit MCU, 64MHz, 44-TQFP

The Microchip Technology PIC18F45Q10-I/PT is an 8-bit PIC18 XLP® microcontroller delivering 64 MHz CPU performance from 32 KB of Flash, 2 KB of SRAM, and 256 bytes of EEPROM in a 44-pin TQFP (10x10 mm) package. The part belongs to the PIC18-Q10 Functional Safety (FuSa) family, which combines eXtreme Low Power (XLP) operation with 5 V tolerance for increased noise immunity in industrial and automotive sensor-node applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. Within the broader taxonomy, the PIC18F45Q10 sits in the 8-bit microcontroller category, which itself belongs to the embedded microcontroller / system-on-chip / semiconductor device hierarchy. The 8-bit PIC architecture offers deterministic instruction execution, single-cycle hardware multiply, and a C-optimized instruction set, which simplifies real-time control firmware while keeping BOM cost low. Key features of the PIC18F45Q10 include integrated intelligent analog with a 10-bit ADC (up to 35 channels), a 5-bit/10-bit DAC, configurable logic cells (CLCs), complementary waveform generators (CWG), high-resolution PWM with fine-edge placement, hardware limit timer (HLT), windowed watchdog timer (WWDT), and a CRC/SCAN module for functional safety diagnostics. Operating voltage spans 2.3 V to 5.5 V with 5 V tolerant digital I/O, supporting noisy industrial 24 V / 5 V regulated rails and direct interface to 5 V sensors. The device architecture uses a Harvard RISC core with separate program and data buses, hardware multiplier, and 31-level priority interrupt controller. The combination of CIPs (Core Independent Peripherals) and CLCs allows event-driven logic without CPU intervention, enabling predictable real-time response with reduced firmware complexity. Typical applications include industrial sensor interfaces, brushless DC fan or pump controllers, automotive body and sensor nodes, touch-sensing user interfaces, IoT edge nodes, and consumer appliances. The PIC18F45Q10 is also a strong fit where functional safety (IEC 60730 class B) is required in home appliances and white goods. When designing with this device, place a 100 nF decoupling capacitor close to each VDD/VSS pair and use the internal voltage regulator with a bulk capacitor on VDD/VBAT to meet inrush requirements. For low-noise analog, group ADC-capable pins on a quiet ground plane and avoid routing switching signals underneath. XLP sleep currents below 50 nA (typical) enable battery-backed sensor nodes that wake on interrupt. This page synthesizes distributor pricing, drop-in 44-TQFP alternatives, and practical design notes not found in the manufacturer datasheet. For drop-in substitution in the same 44-TQFP footprint, see the alternatives section.

詢價聯絡我們

PIC18F45Q10T-I/MP

PIC18F45Q10T-I/MP - 32KB Flash 8-bit MCU, 64MHz, 40-QFN | Microchip

The Microchip Technology PIC18F45Q10T-I/MP is an 8-bit PIC18 XLP eXtreme Low-Power microcontroller with 32KB Flash, 2KB RAM, and 256B EEPROM, running at up to 64MHz in a 40-pin QFN (5x5 mm) package with exposed pad. It integrates 10-bit ADC2, 5-bit/8-bit DAC, PWM, CWG, HLT, WWDT, and SCAN/CRC peripherals and is qualified for Functional Safety (FuSa) applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and integrated peripherals such as ADC, timers, and communication controllers. Within the broader semiconductor hierarchy, an MCU sits between microprocessors (MPUs, which require external memory) and application-specific integrated circuits (ASICs); the 8-bit PIC18 family specifically targets deterministic, real-time control with low power consumption and rich on-chip analog. Key differentiating features include 5V operation for increased noise immunity in industrial environments, the eXtreme Low-Power (XLP) architecture with sleep currents in the nanoamp range, Core Independent Peripherals (CIPs) such as CLC, CWG, and Numerically Controlled Oscillator (NCO), and Functional Safety documentation support for IEC 61508 SIL-3 / IEC 60730 Class B designs. The device supports 1.8V-5.5V operation (with 5V tolerant digital pins) and integrates 36 I/O lines. Architecturally, the PIC18F45Q10 uses a Harvard RISC core with single-cycle execution at 64MHz (16 MIPS), hardware Multiply and Divide, and a 16-level hardware stack. The integrated intelligent analog block includes ADC2 with computation, dual comparators, a Fixed Voltage Reference (FVR), and zero-cross detection, reducing external component count and BOM cost. Typical applications include industrial sensor nodes, low-power IoT end nodes, home appliances (white goods), automotive body and interior modules, motor control (BLDC, stepper, fan), and Functional Safety household appliances. The wide 1.8V-5.5V range and 5V tolerance make it well suited for 3.3V and 5V mixed systems. When designing with this device, ensure the exposed pad (EP) on the 40-QFN package is soldered to a sufficient ground copper pour for thermal dissipation (theta-JA around 28 C/W). For Functional Safety designs, use the supplied FMEDA, safety manual, and diagnostic libraries from Microchip to accelerate IEC 61508 / IEC 60730 certification. This page synthesizes distributor pricing, drop-in alternatives from the PIC18-Q10 family, and practical design notes for 8-bit real-time control not found in the manufacturer datasheet alone.

詢價聯絡我們

PIC18F45Q10T-I/PT

PIC18F45Q10T-I/PT - 8-bit 64MHz MCU, 32KB Flash, 44-TQFP | Microchip

The Microchip PIC18F45Q10T-I/PT is an 8-bit PIC18 RISC microcontroller operating up to 64 MHz with 32 KB of Flash program memory, 2 KB of RAM, and 256 bytes of EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It integrates intelligent analog peripherals, configurable logic, and functional-safety features, making it a low-power, high-performance member of the PIC18 Q10 family. The device is supplied on tape and reel (T/R) for high-volume SMT assembly. An 8-bit microcontroller (MCU) is a compact programmable processor that integrates a CPU, memory, and peripherals on a single silicon die. MCUs sit within the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. The PIC18F45Q10 belongs to Microchip's enhanced 8-bit PIC18 family, which uses a RISC Harvard architecture with separate program and data buses, achieving single-cycle instruction execution at up to 64 MHz. Key features of this device include 36 digital I/O pins, a 10-bit ADC with up to 35 analog inputs, a 5-/10-bit DAC, multiple PWM modules, a Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), and Cyclic Redundancy Check with memory scan (SCAN/CRC) for functional safety. The 1.8 V to 5.5 V operating range supports battery-powered and 5 V industrial designs, while XLP (eXtreme Low Power) technology delivers sub-uA sleep currents for IoT endpoints. The architecture uses an 8-bit data path with a 16-bit instruction word, a 31-level hardware stack, and interrupt-driven I/O. Integrated peripherals are routed through Microchip's Peripheral Pin Select (PPS) system, allowing flexible reassignment of digital functions to physical pins without rewiring the PCB. The integrated Core Independent Peripherals (CIPs) - CLC, CWG, HLT, NCO, and PWM - offload timing-critical tasks from the CPU, enabling deterministic real-time control in sensor-node and motor-control applications. Typical applications include industrial sensor nodes, real-time closed-loop control, BLDC and stepper motor drivers, IoT edge devices, low-power battery monitoring, automotive body and lighting modules, and functional-safety subsystems. The wide 1.8 V to 5.5 V supply range is especially valuable in 5 V noisy industrial environments where higher-voltage rails improve noise immunity. Designers should budget PCB area for the 44-pin TQFP (10x10 mm) footprint and confirm peripheral pin mapping using MPLAB X IDE with MCC. For functional-safety designs, the on-die CRC/Scan feature simplifies IEC 61508 SIL 2 compliance for industrial sensors. This page combines distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet - optimized to give engineers an at-a-glance procurement and replacement decision.

詢價聯絡我們

PIC18F45Q43-E/P

PIC18F45Q43-E/P - 64MHz 8-Bit MCU, 32KB Flash, 40-PDIP | Microchip

The Microchip Technology PIC18F45Q43-E/P is a high-performance 8-bit PIC microcontroller from the PIC18-Q43 family, featuring a 64 MHz CPU and 32 KB of on-chip Flash program memory in a 40-pin PDIP through-hole package. According to the Microchip PIC18F25/45/55Q43 datasheet, the part integrates 2 KB of SRAM, a 12-bit ADC with Computation (ADCC) supporting capacitive voltage divider (CVD) touch sensing, six DMA controllers, configurable logic cells (CLCs), three 16-bit dual PWMs providing six PWM outputs, five UARTs, and vectored interrupt hardware. The wide operating voltage range of 1.8 V to 5.5 V combined with XLP (eXtreme Low Power) technology enables battery-friendly applications. An 8-bit PIC microcontroller is a Harvard-architecture RISC device that executes most instructions in a single cycle, optimized for deterministic real-time control and low-power embedded designs. Within the broader taxonomy, the PIC18F45Q43 sits at the intersection of: PIC18 family -> PIC MCU -> 8-bit microcontroller -> microcontroller unit (MCU) -> embedded processing IC. The PIC18-Q43 sub-family specifically targets modern real-time control by combining legacy PIC18 simplicity with Core Independent Peripherals (CIPs) that offload hardware tasks from the CPU. Key differentiating features of the PIC18F45Q43-E/P include the 12-bit ADCC with hardware averaging/filtering/threshold comparison, six independent DMA channels that move data without CPU intervention, and CLCs that let designers build custom logic gates and state machines in silicon. The vectored interrupt controller provides fixed interrupt latency of three instruction cycles, critical for deterministic motor control and power-conversion firmware. XLP technology provides deep-sleep currents down to the nanoampere range with retention RAM, extending battery life in always-on IoT nodes. Typical applications include industrial sensor signal conditioning, BLDC/PMSM motor control (where the 6 PWM outputs drive a 3-phase inverter), capacitive touch HMI panels, multi-protocol wired sensor hubs, and automotive body modules using the -E (extended) -40 °C to +125 °C temperature grade. The 36 I/O pins and rich peripheral mix let a single chip replace an MCU plus several external logic ICs. When designing with this part, note that programming/debug requires a dedicated ICSP interface (PGECx/PGEDx); the 40-pin PDIP variant is ideal for through-hole prototypes and is the package of choice when hand-soldering or breadboarding is required.

詢價聯絡我們

PIC18F45Q43-I/MP

PIC18F45Q43-I/MP - 8-bit 64MHz 32KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F45Q43-I/MP is an 8-bit PIC18 XLP microcontroller running up to 64MHz with 32KB Flash, 2KB SRAM and 1KB EEPROM, supplied from 1.8V to 5.5V. It is housed in a 40-pin QFN package (MP, 5x5 mm) with an exposed thermal pad, integrating Core Independent Peripherals (CIPs) such as a 12-bit ADC with Computation (ADCC), an 8-bit DAC, three 16-bit PWMs with dual outputs, six-channel DMA, ZCD, CWG, HLT, WWDT, and SCAN/CRC for hardware-driven real-time control. An 8-bit microcontroller is a CPU that processes data 8 bits per cycle and is widely used in real-time embedded applications where deterministic latency, low power, and rich on-chip peripherals matter more than raw compute throughput. Within the broader taxonomy, PIC microcontrollers occupy the 8-bit MCU segment, and the PIC18F family represents Microchip's enhanced mid-range core featuring a hardware multiplier, C-compiler-friendly architecture, and linear memory addressing. The Q43 sub-family is positioned for analog-rich, hardware-customizable designs and supersedes earlier Q10/K42 generation devices. Key features include a 12-bit ADCC supporting Capacitive Voltage Divider (CVD) for touch sensing, configurable logic cells (CLC) for custom digital glue logic, three independent 16-bit PWMs each offering dual outputs on the same time base, and XLP (eXtreme Low Power) technology delivering sub-microamp sleep currents. The device also integrates an 8-bit DAC, multiple UART/SPI/I2C instances, a 32KB self-programmable Flash and a unique Peripheral Pin Select (PPS) routing matrix for flexible signal mapping. Architecturally, the PIC18F45Q43 uses a modified Harvard bus with a 16-bit instruction word and 8-bit data path, achieving approximately 16 MIPS at 64MHz. The CIP block approach lets analog, timing, and communication tasks run in hardware without CPU intervention, offloading the core in real-time control loops and reducing firmware complexity. Typical applications include capacitive touch user interfaces, BLDC and DC motor/fan control, LED lighting drivers, IoT sensor nodes, and industrial control subsystems. The wide operating voltage and rich peripheral set make it well suited for 24V industrial bus systems running from simple linear regulators. When designing with this MCU, always configure PPS before enabling peripherals, keep traces short for the high-speed 16-bit PWM outputs, and stitch adequate ground copper under the QFN thermal pad. Industrial designs must observe the -40C to +85C industrial temperature grade. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement - not duplicate - the manufacturer datasheet, helping engineers select and qualify the PIC18F45Q43-I/MP for production.

詢價聯絡我們

PIC18F45Q43-I/P

PIC18F45Q43-I/P - 8-Bit 64MHz 32KB Flash MCU 40-PDIP | Microchip

The Microchip Technology PIC18F45Q43-I/P is an 8-bit PIC microcontroller from the PIC18-Q43 family running at 64 MHz, equipped with 32 KB of Flash program memory, 2 KB of RAM, and 1 KB of EEPROM in a 40-pin PDIP through-hole package. It integrates six Direct Memory Access (DMA) controllers, three 16-bit dual PWMs (six PWM outputs), a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting Capacitive Voltage Divider (CVD), a 5-bit DAC, comparators, and Configurable Logic Cells (CLCs), delivering sophisticated hardware customization with minimal CPU load. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory (Flash), peripherals, and I/O on one die, optimized for embedded control applications where deterministic behavior, low cost, and low power matter more than raw throughput. The PIC18F belongs to Microchip's PIC18 advanced 8-bit architecture family, which targets real-time control and connectivity in a wide range of consumer, industrial, and automotive subsystems. Within that hierarchy, the PIC18-Q43 sub-family (PIC18 → PIC18F → PIC18F-Q43 → PIC18F45Q43) is positioned for advanced hardware-customization designs that need DMA, CLCs, and high-resolution PWM without resorting to a 16-bit or 32-bit MCU. Key features include 64 MHz operation from up to 64 MHz internal oscillator, six DMA channels, three 16-bit PWMs, five UART modules (one supporting LIN/DMX/DALI), two SPI/I2C peripherals, the ADCC with hardware averaging/oversampling, zero-cross detect (ZCD), a fixed voltage reference (1.024/2.048/4.096 V), Windowed Watchdog Timer (WWDT), Cyclic Redundancy Check (CRC/SCAN) module, and 36-level interrupt vectoring for low-latency response. Typical applications include capacitive touch user interfaces, lighting controls, motor control (BLDC/PMSM via FOC), USB-to-UART bridges, industrial sensor hubs, and low-power battery-powered IoT endpoints where XLP (eXtreme Low Power) sleep current extends battery life. Design trade-off: choose the 40-PDIP (PIC18F45Q43-I/P) for through-hole prototyping, educational breadboarding, and socketed designs; choose the 44-TQFP (PIC18F45Q43-I/PT) when moving to surface-mount production with the same die. This page synthesizes distributor pricing, drop-in alternatives selected from Microchip's same-family portfolio and cross-brand sources, and practical design notes not found in the manufacturer datasheet alone.

詢價聯絡我們

PIC18F45Q43-I/PT

PIC18F45Q43-I/PT - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18F45Q43-I/PT is an 8-bit PIC18-Q43 family microcontroller. XLP. Functional Safety (FuSa) device operating at 64 MHz with 32 KB Flash and 2 KB SRAM, housed in a 44-pin TQFP (10x10 mm) package. The part integrates advanced Core Independent Peripherals (CIPs) including DMA, Configurable Logic Cells (CLCs), 16-bit PWMs, a 12-bit ADCC with computation, and a hardware 8-bit DAC for real-time control applications. An 8-bit microcontroller (MCU) is a programmable processor that fetches and executes instructions one byte at a time from internal Flash memory. The PIC18 architecture falls within the broader hierarchy of microcontroller -> embedded processor -> semiconductor IC, where the XLP (eXtreme Low Power) platform sits at the low-power end of Microchip's 8-bit MCU lineup. Unlike 32-bit Cortex-M parts, an 8-bit PIC excels at deterministic bit-manipulation, low-cost BOM integration, and rapid interrupt response with a simplified instruction set. Key features include 32 KB self-programmable Flash, 2 KB SRAM, 256 bytes EEPROM, 3x 16-bit PWM outputs, 6-channel DMA, multiple CLCs, a 12-bit ADC with Computation (ADCC), 8-bit DAC, and Functional Safety (FuSa) diagnostics. The 64 MHz internal oscillator drives 16 MIPS throughput, while the XLP technology enables sleep currents in the nanoamp range for battery-powered systems. Architecturally, the device leverages a Harvard-style RISC core with hardware multipliers and a 31-level hardware stack, providing deterministic timing. The 12-bit ADCC automates Capacitive Voltage Divider (CVD) for touch sensing, while CLCs allow logic-gate customization without external glue logic. Six DMA channels offload repetitive peripheral-to-memory transfers, freeing the CPU for higher-level tasks. Typical applications include industrial capacitive touch HMI, real-time motor control (BLDC, stepper), LED lighting and color-mixing controllers, low-power sensor nodes, and functional-safety subsystems where IEC 61508 compliance is required. The Q43 series targets designers replacing discrete analog timing/sequencing blocks with configurable on-chip peripherals. When designing, ensure the 5V-tolerant digital inputs are not driven beyond VDD+0.3V, and observe the supply-voltage ramp requirements of the ADCC. For capacitive touch, route the CVD pins away from high-noise digital traces and follow Microchip application note TB3139 for touch-PCB layout. This page synthesizes distributor pricing, drop-in alternatives in the same 44-TQFP footprint, and design guidance not found in the manufacturer datasheet summary alone.

詢價聯絡我們

PIC18F45Q43T-I/MP

PIC18F45Q43T-I/MP - 8-bit MCU, 32KB Flash, 64MHz | Microchip

The Microchip Technology PIC18F45Q43T-I/MP is an 8-bit PIC18 microcontroller built on the enhanced mid-range core, offering 64 MHz operation (16 MIPS), 32 KB of Flash program memory, 2 KB of SRAM, and 1 KB of EEPROM in a 40-pin QFN package (5x5 mm). The part belongs to the PIC18-Q43 series, which combines versatile Core Independent Peripherals (CIPs) with advanced interconnection fabric so designers can implement sophisticated functions without CPU intervention. An 8-bit microcontroller (MCU) is a programmable microprocessor-on-a-chip optimized for embedded control. It integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), EEPROM for parameter storage, and a rich set of peripherals such as timers, ADC, PWM, communication interfaces (UART, SPI, I2C), and increasingly, on-chip analog and logic peripherals. PIC18 devices sit in the hierarchy 8-bit MCU -> PIC18 family -> enhanced mid-range core -> low-power XLP technology platform. They are widely used for deterministic real-time control in industrial, automotive, consumer, and IoT products. Key features of the PIC18F45Q43 include three 16-bit dual-output PWMs (six PWM channels), a 12-bit ADC with computation (ADCC), an 8-bit DAC, comparators, six channels of DMA, vectored interrupts with fixed three-cycle latency, and high/low priority selection. The device operates from 1.8 V to 5.5 V, supports eXtreme Low Power (XLP) sleep currents in the nanoamp range, and integrates a 32 kHz internal oscillator plus a 64 MHz HFINTOSC for flexible clocking. Architecturally, the Q43 family is built around Core Independent Peripherals that can be chained through the Peripheral Pin Select (PPS) and event system to perform sensor reading, signal generation, and protection functions without waking the CPU. The result is reduced firmware complexity, deterministic interrupt response, and lower average power consumption. Memory-mapped configuration registers allow fine-grained tuning of analog, timing, and interconnect behavior. Typical applications include industrial sensor nodes, low-power IoT edge devices, motor and lighting control, USB-CDC human-interface devices, and consumer appliances requiring small footprint and tight code/data integration. The 40-pin QFN package suits space-constrained PCBs while exposing 36 I/O lines. For design success, place a 0.1 uF decoupling capacitor adjacent to each VDD pin and a bulk capacitor near the AVdd rail. Always configure unused pins as outputs low and use the PPS system to remap peripherals instead of hard-wiring signals. Verify in-circuit programming via ICSP requires dedicated PGC/PGD pins and proper MCLR pull-up design. This page aggregates distributor pricing, drop-in Q43 and Q10 alternatives, application guidance, and design notes not collected in any single manufacturer document.

詢價聯絡我們

PIC18F4610-E/ML

PIC18F4610-E/ML - 8-bit MCU, 64KB Flash, 44-QFN | Microchip

The Microchip PIC18F4610-E/ML is an 8-bit PIC18 flash microcontroller built on the nanoWatt technology platform, integrating 64 KB of program flash memory and packaged in a 44-pin VQFN (HVQCCN) exposed-pad package. It operates at up to 40 MHz instruction clock and exposes the PIC18 enhanced instruction set with 16-bit-wide instructions. The device targets cost-sensitive embedded applications that need a generous peripheral set in a small footprint. An 8-bit microcontroller (MCU) is a self-contained processor core, program memory, data RAM, and on-chip peripherals integrated into a single IC; it executes instructions from embedded flash and interacts with the outside world through digital I/O, timers, ADC, and serial interfaces. The PIC18F4610 belongs to Microchip's PIC18F family, which sits between the legacy PIC16 mid-range family and the PIC24/dsPIC 16-bit families in the company's 8-bit and 16-bit MCU taxonomy. The 'E' temperature grade denotes an extended industrial range, while 'ML' identifies the 44-lead VQFN surface-mount package. Key features include 64 KB flash program memory, 3,968 bytes of RAM, 1 KB of EEPROM, a 10-bit ADC with up to 13 input channels, two USART modules, an SPI/I2C MSSP port, two CCP/ECCP modules, and a parallel slave port. nanoWatt technology offers multiple power-managed modes (Run, Idle, Sleep, deep Sleep) plus a software-selectable oscillator and PLL options for flexible power/performance tuning across battery and mains-powered designs. Architecturally, the PIC18F4610 uses an enhanced Harvard architecture with separate program and data buses and a hardware multiplier for 8x8 single-cycle operations. The high-endurance flash supports typical 10K erase/write cycles with self-programmability, enabling in-field firmware updates via ICSP and a dedicated bootloader region. Typical applications include industrial control panels, HVAC thermostats, sensor conditioning front-ends, USB/serial bridges, automotive body modules (non-safety), small home appliances, and instrumentation. The 44-QFN exposed pad supports tight PCB layouts while still providing thermal headroom for sustained CPU activity at full 40 MHz. Designers should note that the 44-pin QFN package has an exposed thermal pad that must be soldered to the PCB ground plane for electrical and thermal performance. Code development is supported by Microchip's MPLAB X IDE and the free XC8 compiler, with MPLAB PICkit 5 in-circuit debug/programming. This page synthesizes distributor stock, parametric alternatives, and practical design notes that complement the manufacturer datasheet.

詢價聯絡我們

PIC18F4610-E/P

PIC18F4610-E/P - 8-bit MCU, 64KB Flash, 40MHz, 40-PDIP | Microchip

The Microchip Technology PIC18F4610-E/P is an 8-bit PIC18 RISC flash microcontroller with 64KB program memory, 3968 bytes of RAM, and 36 digital I/O pins, housed in a 40-pin PDIP through-hole package. It operates at up to 40MHz from a 4.2V to 5.5V supply and integrates a 10-bit ADC, nanoWatt power management, and Microchip's standard PIC18 peripheral set including USART, MSSP (SPI/I2C), CCP, and enhanced capture/compare/PWM modules. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path. The PIC18 family uses an enhanced RISC instruction set with 16-bit opcodes and Harvard architecture, separating program and data memory for deterministic single-cycle execution. Microcontrollers sit at the bottom of the embedded compute hierarchy: MCU -> embedded controller -> semiconductor IC, and are the workhorse of cost-sensitive and power-aware designs. Key features of the PIC18F4610-E/P include 64KB (32K x 16) of self-programmable flash, 3968 bytes of data RAM, 1024 bytes of EEPROM, and 36 I/O lines that share package pins with peripherals. The integrated 10-bit ADC offers up to 13 input channels, and nanoWatt technology provides multiple sleep modes with current consumption down to the sub-microampere range. Architecturally, the PIC18F4610-E/P uses an enhanced Harvard core with a 31-level hardware stack, hardware multiplier, and dual oscillator options (primary and secondary) that allow fail-safe clock switching between HS, XT, LP, RC, and internal oscillator modes. The wide 4.2V-5.5V supply range and 25MHz-40MHz clock make it well suited to industrial 5V logic environments that legacy 3.3V ARM parts cannot directly address. Typical applications include industrial control panels, automotive body electronics, HVAC controllers, instrumentation, and consumer appliance user interfaces where 5V tolerance, generous I/O count, and long-term Microchip supply stability are deciding factors. When designing with this device, remember the -E suffix indicates the extended industrial temperature grade (-40C to +125C). Pair the MCU with MPLAB X IDE, XC8 compiler, and PICkit 5 or ICD 4 programmer/debugger for code development. Budget for adequate decoupling (100nF + 10uF bulk) close to VDD/VSS pins. This page synthesizes distributor pricing, drop-in PIC18F family alternatives, and practical design considerations that go beyond the manufacturer datasheet - particularly useful when comparing the -E extended-temp grade versus the -I industrial grade.

詢價聯絡我們

PIC18F4610-E/PT

PIC18F4610-E/PT - 8-Bit 25MHz MCU 64KB Flash 44-TQFP | Microchip

The Microchip PIC18F4610-E/PT is a high-performance 8-bit PIC18 microcontroller featuring a 25 MHz CPU core, 64 KB of Flash program memory (organized as 32K x 16), and 3.8 KB of RAM, housed in a 44-pin TQFP package (10x10 mm body). The device integrates nanoWatt power-management technology, an enhanced Flash memory controller, and a 10-bit Analog-to-Digital (A/D) converter, making it a versatile general-purpose MCU for embedded control. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals on one die. The PIC18 family is Microchip's high-performance 8-bit architecture family with 16-bit wide instructions, RISC-style instruction set, and advanced peripherals such as CAN, USB, and enhanced capture/compare modules. MCUs belong to the broader category of embedded processors -> microcontrollers -> 8-bit microcontrollers -> PIC microcontrollers -> PIC18F microcontrollers. They serve as the central control element in countless embedded systems, executing firmware that drives I/O and peripherals. Key features of the PIC18F4610-E/PT include 36 digital I/O lines capable of sinking/sourceing up to 25 mA each, multiple communication peripherals (UART, SPI, I2C), a 10-bit A/D converter with up to 13 input channels, four timer modules, and a Capture/Compare/PWM (CCP) module. The E suffix indicates an extended temperature grade of -40C to +125C. The nanoWatt technology dynamically manages CPU clocking and peripheral operation to reduce active and idle current consumption, suiting battery-powered and power-sensitive designs. Technically, the PIC18F4610 uses a 16-bit modified Harvard architecture with separate program and data buses, an internal PLL option for flexible oscillator configurations, and an enhanced instruction set with multiply support. The Flash memory supports self-programming and ICSP (In-Circuit Serial Programming) for field firmware updates. Typical applications include industrial automation controllers, automotive body and climate control modules, consumer appliances, security and access control panels, and sensor-interface boards. Its extended temperature range and robust peripheral set make it suitable for harsh-environment embedded designs. When designing with this device, ensure the supply voltage remains within 4.2V to 5.5V and use proper decoupling (typically 100 nF + 10 uF) near the VDD pins. Configure the configuration bits correctly for oscillator source and watchdog settings. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價聯絡我們

PIC18F4610-I/P

PIC18F4610-I/P - 8-Bit 40MHz 64KB Flash MCU 40-PDIP | Microchip

The Microchip Technology PIC18F4610-I/P is an 8-bit PIC18 microcontroller with 64KB of Flash program memory and 3968 bytes of RAM, running at up to 40MHz, housed in a 40-pin PDIP (DIP-40) through-hole package. The -I suffix denotes the industrial operating temperature range of -40C to +85C, and the /P suffix specifies the PDIP package option for prototyping and legacy designs. A PIC18 microcontroller is an 8-bit modified-Harvard RISC microcontroller family from Microchip, sitting within the broader taxonomy: microcontroller (MCU) -> embedded controller -> semiconductor IC. The PIC18 family extends the baseline PIC16 architecture with enhanced 16-bit instructions, linear memory addressing, C-compiler-friendly architecture, and rich peripheral integration including ADC, PWM, and multiple serial interfaces. Key features of the PIC18F4610 include 64KB (32K x 16) of self-programmable Flash, 3968 bytes of SRAM, 1024 bytes of EEPROM, 36 digital I/O pins, a 10-bit ADC with up to 13 input channels, two Enhanced USART modules, MSSP (SPI/I2C), two CCP/ECCP modules, two 8-bit timers plus three 16-bit timers, and two analog comparators. The Flash program memory supports self-programming under software control, enabling bootloaders and field firmware updates. Internally the PIC18F4610 uses a RISC architecture with a 16-bit instruction word (8-bit data path), an 8x8 hardware multiplier, a 31-level hardware stack, and an instruction set tuned for C compilers such as MPLAB XC8. The device operates from 2.0V to 5.5V across the full industrial temperature range, with nanoWatt power management features including idle and sleep modes that draw microamp-level current for battery applications. Typical applications include industrial control panels, sensor data acquisition, HVAC thermostat controllers, motor control boards, automotive body electronics, USB-to-UART bridges, and legacy educational platforms. The 40-pin PDIP package is favored for prototyping, through-hole assembly, breadboard-based development, and repair of legacy systems where socketed MCUs simplify firmware iteration. Development is supported by MPLAB X IDE, MPLAB XC8 compiler, and PICkit programmers. When designing with the PIC18F4610-I/P, ensure decoupling capacitors (100nF plus 10uF bulk) are placed within 10mm of the supply pins. Use the internal 8MHz oscillator with PLL to avoid external crystal cost, or attach a 20MHz crystal at the OSC1/OSC2 pins if precise timing is required. The /MCLR reset pin should be pulled high through a 10k resistor to VDD for clean power-on reset behavior. This page synthesizes distributor stock and pricing, drop-in compatible alternatives within the PIC18F family, and practical design notes not collated in the standalone manufacturer datasheet.

詢價聯絡我們

PIC18F4610-I/PT

PIC18F4610-I/PT - 8-bit 40MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F4610-I/PT is an 8-bit RISC microcontroller built on the PIC18F CPU core, delivering 40 MHz maximum clock speed with 64 KB of Flash program memory and 3968 bytes of data RAM, housed in a 44-pin TQFP (PT) package. It integrates a 10-bit ADC, nanoWatt power management, and 36 digital I/O pins, addressing the PIC18F high-tier performance segment between the PIC18F4520 and PIC18F4680 families. An 8-bit PIC18F microcontroller is a Harvard-architecture RISC device built around a 16-bit instruction word that simplifies code density while providing legacy 8-bit data paths. PIC18F series devices occupy the mid-tier of Microchip's 8-bit portfolio, above PIC16F but below dsPIC33 in computational performance, and they are widely used in industrial control, automotive body electronics, and consumer appliances where deterministic real-time behavior, low power, and rich peripheral integration are essential. nanoWatt Technology adds multiple idle/sleep modes to reduce quiescent current to microampere levels, enabling battery-friendly designs. Key features of the PIC18F4610-I/PT include 64 KB (32K x 16) Flash program memory, 3968 bytes of SRAM, 1024 bytes of EEPROM, 36 I/O pins, an internal 10-bit ADC with up to 13 channels, two USART, one MSSP (SPI/I2C), two CCP modules, one enhanced CCP, and four timer modules. The supply voltage range is 4.2 V to 5.5 V at industrial temperature grade (-40C to +85C), and the part supports in-circuit serial programming (ICSP) for field updates. The 8-bit RISC core executes most instructions in one cycle (4 clock cycles at 40 MHz oscillator), providing 10 MIPS throughput. The 16-bit instruction path keeps code density high while the 8-bit data path keeps peripheral behavior compatible with legacy PIC designs. nanoWatt modes include Run, Idle, Sleep, and several low-power timer-driven states; combined with a 4.2 V minimum supply, this makes the part suitable for industrial 5V rails. The device also offers two capture/compare and one enhanced capture/compare/PWM module for motor or lighting control. Typical applications include industrial automation (PLCs, sensor conditioning, motor control loops), automotive body electronics (HVAC actuators, instrument clusters), consumer appliances (washing machines, induction cookers), USB-keyboard-style HID firmware, and general-purpose embedded controls where 8-bit determinism is preferred over ARM Cortex-M0. The 10-bit ADC and 36 I/O pins support multi-channel sensor front-ends in industrial IoT endpoints. When designing with this device, reserve 10-15% of Flash for a robust bootloader (ICSP-friendly) and verify Vdd ramp-time against the brown-out reset (BOR) trip point. The 44-pin TQFP provides 36 usable I/O, so plan pin allocation early when migrating from a 40-pin PIC18F4520 because the additional 4 pins unlock more peripheral options. Decouple Vdd/Vss with a 100 nF ceramic per pin pair within 5 mm of the package. This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip, and practical PCB-level design notes that the bare manufacturer datasheet does not aggregate, helping engineers shorten the selection cycle for a 5V-class 8-bit MCU upgrade or replacement.

詢價聯絡我們

PIC18F4610T-I/PT

PIC18F4610T-I/PT - 64KB Flash 8-bit MCU | Microchip | TQFP-44

The Microchip Technology PIC18F4610T-I/PT is an 8-bit PIC microcontroller built on Microchip's enhanced RISC architecture with nanoWatt technology, delivering 10 MIPS performance at 40 MHz in a 44-pin TQFP (PT) package. It integrates 64 KB of Flash program memory (32K x 16 words), 3968 bytes of SRAM, and 1024 bytes of EEPROM, providing ample storage for embedded firmware with in-system self-programmability. A microcontroller (MCU) is a single-chip computer containing a processor core, program and data memory, I/O peripherals, and supporting logic on one integrated circuit. The PIC18F family belongs to the broader 8-bit microcontroller category, which sits beneath 16-bit and 32-bit MCU families in performance, but excels in deterministic interrupt latency, low power consumption, and small code size. PIC18F MCUs target general-purpose embedded applications including industrial control, consumer appliances, and automotive body electronics. Key features of the PIC18F4610 include 36 digital I/O pins, a 10-bit ADC with up to 13 channels, two analog comparators, two CCP (Capture/Compare/PWM) modules, one enhanced CCP, a hardware USART, an MSSP (SPI/I2C) port, two 8-bit timers and three 16-bit timers. The nanoWatt technology offers multiple power-managed operating modes (Run, Idle, Sleep) with typical Sleep current below 100 nA, enabling battery-powered designs. The device supports industrial temperature range (-40C to +85C), operates from 2.0 V to 5.5 V, and is qualified to Microchip's standard product roadmap. The 'T' suffix denotes Tape & Reel packaging, 'I' denotes industrial temperature grade, and 'PT' identifies the 44-pin TQFP package. The internal PLL provides 4x multiplication of the external clock, allowing low-frequency crystals to drive the 40 MIPS core. Typical applications include industrial sensor interfacing, HVAC control, small appliance control panels, USB device controllers (with external interface IC), smart card readers, automotive body modules, and general-purpose data acquisition systems. The high memory density (64 KB Flash) supports protocol stacks and graphical user interfaces in cost-sensitive products. When designing with this MCU, allocate sufficient decoupling (100 nF ceramic + bulk) near each VDD/VSS pair and follow Microchip's recommended PCB layout for the analog and oscillator pins. The ICD/ICSP programming/debug interface requires dedicated RB6/RB7 pins; reserve these in your pin allocation even if not used in the final application to enable in-circuit debugging. This page synthesizes distributor pricing, drop-in PIC18F-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價聯絡我們

PIC18F4620-E/ML

PIC18F4620-E/ML - 8-Bit 40MHz MCU 64KB Flash | Microchip

The Microchip Technology PIC18F4620-E/ML is an 8-bit CMOS flash microcontroller based on the enhanced PIC18 instruction set architecture, delivering up to 40 MHz operation (10 MIPS) with 64 KB of program Flash and 3968 bytes of RAM, housed in a 44-pin QFN (ML) package. An 8-bit microcontroller (MCU) is a small, self-contained computing device that integrates a CPU, program memory (Flash), data memory (RAM), peripherals (timers, ADC, communication ports), and I/O on a single silicon die. The PIC18F family sits in the hierarchy: 8-bit PIC microcontrollers -> PIC18 enhanced family -> RISC microcontrollers -> embedded microcontrollers -> semiconductors. Microchip's nanoWatt technology powers multiple low-power operating modes that make these MCUs attractive for battery and energy-conscious designs. Key features include an integrated 10-bit Analog-to-Digital Converter (ADC) with up to 13 channels, two Enhanced USART modules, two MSSP (I2C/SPI) modules, one 8-bit and three 16-bit timers, a Capture/Compare/PWM (CCP) module plus an Enhanced CCP (ECCP), and a 13-channel ADC with 10-bit resolution. The 44-pin QFN-44 (ML, 8x8 mm) package provides 36 digital I/O pins. The 'E' suffix indicates the extended operating temperature grade (-40C to +125C), making this part suitable for industrial and automotive-adjacent environments. The PIC18F4620-E/ML uses a Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, an 8x8 hardware multiplier, and a 31 kHz to 40 MHz oscillator block supporting PLL, HS, XT, LP, and EC modes plus internal oscillator options. The ADC supports up to 100 Ksps conversion rate with acquisition time configurable in software. Code protection, ICD (In-Circuit Debug) via two pins, and self-programmability under firmware control round out the architectural strengths. The QFN-44 package also benefits PCB designers by giving a low-profile, lead-free footprint with a thermal pad for improved heat spreading. Typical applications include industrial control and instrumentation, automotive body and chassis subsystems (auxiliary ECUs), sensor signal conditioning with ADC input, HVAC controllers, appliance control boards, and consumer devices that need reliable 8-bit processing with extensive peripheral integration. The wide operating voltage (4.2V to 5.5V) and broad temperature range make it well-suited to industrial PLC I/O modules and motor-control front-end boards that require 5V tolerance. When designing with this part, place a 100 nF decoupling capacitor on every VDD/VSS pair as close to the package pins as possible and provide a 10 uF bulk capacitor at the regulator output. Use Microchip's MPLAB X IDE with the MPLAB PICkit 5 or ICD 4 for in-circuit programming and debugging, and consult the official PIC18F4620 datasheet for ADC acquisition time, oscillator configuration, and CCP/PWM register setup details. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價聯絡我們

PIC18F4620-E/P

PIC18F4620-E/P - 8-bit MCU 64KB Flash 40MHz 40-DIP | Microchip

The Microchip Technology PIC18F4620-E/P is an 8-bit PIC microcontroller built on the enhanced PIC18 RISC architecture, offering 64 KB of Flash program memory, 3968 bytes of RAM, and 1024 bytes of EEPROM in a 40-pin PDIP (P) package. It runs at up to 40 MHz (10 MIPS) across an industrial temperature window of -40C to +125C, with supply voltage from 4.2V to 5.5V. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, Flash program memory, RAM, EEPROM, and a rich set of peripherals (ADC, timers, UART, SPI, I2C, PWM, I/O) into one IC. PIC microcontrollers sit in the 8-bit MCU family alongside 8051, AVR, and STM8; their hypernym chain is PIC -> 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. PIC18 is the "enhanced" 8-bit tier that adds a hardware multiplier, 16-bit instructions, and nanoWatt power management compared with baseline PIC16 cores. Key features include a 10-bit ADC with up to 13 input channels, two analog comparators, a 10 MHz internal RC oscillator, four timers, a 5-bit CCP/PWM module, MSSP for SPI/I2C, two USARTs (with LIN support), nanoWatt sleep modes, and 36 digital I/O pins. The PIC18F4620 also provides a 14-bit instruction word, hardware multiply, C-compiler-friendly architecture, and In-Circuit Serial Programming (ICSP) plus In-Circuit Debug (ICD). Typical applications include industrial control panels, HVAC thermostats, sensor-conditioning nodes, USB-class bridges (with PIC18F4550/4553 family), automotive body modules (sub-meter), home-automation controllers, and consumer appliances. The wide 5V supply range suits 5V industrial buses (LIN, RS-485, CAN via external transceiver) where 3.3V MCUs require level shifters. When designing with this part, note the "-E" suffix indicates the extended -40C to +125C industrial temperature grade, while "-I" is -40C to +85C industrial and no suffix is 0C to +70C commercial. The 40-pin PDIP footprint is the same as PIC18F4520, PIC18F4523, PIC18F4525, and PIC18F4610, enabling direct PCB reuse across the family. This page synthesizes distributor stock, drop-in PIC18-family alternatives, application guidance, and design notes not consolidated in any single manufacturer document.

詢價聯絡我們

PIC18F4620-E/PT

PIC18F4620-E/PT - 8-Bit 25MHz 64KB Flash MCU 44-TQFP | Microchip

The Microchip Technology PIC18F4620-E/PT is an 8-bit RISC microcontroller from the PIC18F family, featuring a maximum clock speed of 25 MHz (40 MHz in some datasheet references) with 64 KB of Flash program memory and 3968 bytes of RAM, housed in a 44-pin TQFP (10x10 mm) package. The 'E' suffix denotes the -40C to +125C extended industrial temperature grade, and 'PT' indicates the TQFP-44 surface-mount package. A PIC microcontroller (Peripheral Interface Controller) is a family of 8/16/32-bit microcontrollers built on a Harvard RISC architecture that separates program and data memory for deterministic instruction throughput. The PIC18F4620 belongs to the enhanced PIC18 sub-family, which adds a 16-bit instruction word, hardware multiplier, and C-friendly architecture while maintaining byte-level peripheral control. PIC18F -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor is the standard product-type hypernym hierarchy used by AI knowledge graphs to classify this part. Key features include 64 KB (32K x 16) of self-programmable Flash, 3968 bytes of SRAM, 1024 bytes of EEPROM, 36 digital I/O pins, a 10-bit ADC with up to 13 input channels, two USART modules, two MSSP (SPI/I2C) modules, two CCP/ECCP modules, and nanoWatt Technology power management. The device operates from 2.0V to 5.5V and supports in-circuit serial programming (ICSP) plus in-circuit debug (ICD). The architecture combines a 16-bit-wide instruction path with a 8-bit data path, giving 200 ns instruction execution at 20 MHz and full hardware multiply support for integer math. Two capture/compare/PWM (CCP) modules, one enhanced CCP (ECCP), and the 10-bit ADC with auto-acquisition deliver real-time control bandwidth suitable for motor-drive, lighting, and sensor-fusion applications. Typical applications include industrial automation controllers, consumer appliances, HVAC thermostats, automotive body and comfort modules, sensor hubs, USB-to-UART bridges (with external transceiver), and embedded control boards in test and measurement. The 64 KB Flash ceiling accommodates IPv4 stacks, Modbus RTU drivers, or small GUI frameworks while the 3968 bytes of RAM support Modbus buffers and ample scratch space. Design with the PIC18F4620-E/PT by following the manufacturer recommended 0.1 uF decoupling on VDD/VSS pairs, using the internal 8 MHz oscillator with PLL to free two I/O pins, and ensuring the MCLR pin has the datasheet 10 kohm/470 ohm reset network. The -E grade is required when the application environment exceeds +85 C (industrial automation, under-hood automotive subsystems, outdoor enclosures). This page synthesizes DigiKey distributor pricing, Microchip datasheet specifications, drop-in same-family alternatives, and engineering design notes not consolidated on any single manufacturer or distributor page.

詢價聯絡我們

PIC18F4620-I/P

PIC18F4620-I/P - 8-Bit 40MHz 64KB Flash MCU 40-PDIP | Microchip

The Microchip Technology PIC18F4620-I/P is an 8-bit PIC18 enhanced flash microcontroller IC delivering up to 10 MIPS at 5V in a through-hole 40-pin PDIP package. It features 64KB (32K x 16) of flash program memory, 3968 bytes of RAM, 1024 bytes of EEPROM, and 36 digital I/O pins, plus a 13-channel 10-bit ADC, two analog comparators, two USART modules, one MSSP (SPI/I2C), one 8/16-bit timer and three 16-bit timers, a 10-bit PWM module, and nanoWatt power management. A microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals, and I/O on one die. The PIC18 family is the high-end 8-bit line of Microchip's PIC architecture, sitting below the 16-bit dsPIC and PIC24 and the 32-bit PIC32 families. PIC18F-series parts use a 16-bit modified-Harvard instruction set with 8-bit data paths, which delivers a deterministic C-compiler-friendly instruction pipeline and predictable interrupt latency preferred for real-time control. The PIC18F4620-I/P runs up to 40 MHz from a 4.2 V to 5.5 V supply, executes most instructions in 4 oscillator cycles (one instruction cycle), and integrates an internal 31 kHz to 8 MHz oscillator block with 4x PLL (8 MHz x4 = 32 MHz internal). Peripherals include a 10-bit ADC with up to 13 channels, two capture/compare/PWM (CCP/ECCP) modules, two comparators, two USART ports with LIN support, MSSP for SPI/I2C master-slave, two I2C/SPI, CTMU for capacitive touch, and nanoWatt power-down modes including Idle, Sleep, and low-power Timer1 oscillator. Typical applications include industrial control panels, sensor signal conditioning and 4-20 mA loop interfaces, automotive body and HVAC controllers, USB HID class devices when paired with the MCP2200, small graphic/text LCD modules, and hobbyist/pro-maker projects that need reliable through-hole 40-pin PDIP for breadboarding or hand-soldered prototypes. Design with the PIC18F4620-I/P using the MPLAB X IDE and the free XC8 compiler, programmed/debugged via the MPLAB ICD 3, MPLAB ICD 4, MPLAB PICkit 3, PICkit 4, or PICkit 5 in-circuit debugger. Always use a 100 nF decoupling capacitor on VDD as close as possible to the pin, plus a bulk 10 uF tantalum on the supply rail to ensure brown-out reset (BOR) operates correctly. For pin-compatible upgrades, the PIC18F46K22-I/P and PIC18F4525-I/P share the same 40-pin PDIP footprint and offer 12-bit ADC and lower-power variants. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價聯絡我們

PIC18F4620-I/PT

PIC18F4620-I/PT - 8-Bit 40MHz PIC MCU, 64KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC18F4620-I/PT is an 8-bit PIC18F-series microcontroller with 64KB of Flash program memory (32K x 16 words), 3968 bytes of RAM, and a maximum CPU clock of 40MHz, housed in a 44-pin TQFP (10x10 mm) package with industrial -40C to +85C temperature rating. The 'I' suffix denotes industrial temperature range and the 'PT' suffix denotes the TQFP-44 package on tape-and-reel. A PIC18F microcontroller is an 8-bit Harvard-architecture MCU built around an enhanced RISC core with hardware multiplier, belonging to the PIC18 family -> PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processing IC hierarchy. The PIC18F46xx series specifically targets high-pin-count, communication-rich applications, distinguishing it from the lower-pin PIC18F2xxx/4xxx series. Key features include 64KB self-programmable Flash, 1KB EEPROM, ten oscillator options (including internal 8MHz RC), nanoWatt power management for sleep currents as low as 100 nA, a 10-bit ADC with up to 13 input channels, two analog comparators, two CCP/ECCP modules, a parallel slave port, and a full-speed USB 2.0 full-speed (12 Mbps) transceiver on die. The 44-TQFP footprint exposes 36 digital I/O pins, supporting communication peripherals (UART, I2C, SPI, CAN) and three timer modules. Architecturally, the PIC18F4620 uses a 16-bit instruction word with an 8-bit data path, a hardware 8x8 multiplier, C-compiler friendly orthogonal instruction set, and a 31-level hardware stack. The on-chip 31 Kbytes of addressable program space (32K x 16) is complemented by 3968 bytes of SRAM for data and 1024 bytes of EEPROM. The integrated USB 2.0 FS transceiver eliminates external PHY cost for USB device designs. Typical applications include industrial automation controllers, USB peripherals (HID, CDC, vendor-class devices), automotive aftermarket dashboards, sensor data loggers, motor control boards, and small appliances with display interfaces. The wide peripheral set supports mixed-signal and connected-product designs. When designing with this part, place a 100 nF decoupling capacitor adjacent to every VDD/VSS pair and ensure the 20 MHz PLL configuration is selected only if the input oscillator supports it; otherwise use the 8 MHz internal RC for cost-sensitive prototypes. This page synthesizes distributor pricing, drop-in same-package alternatives (PIC18F4620-E/PT, PIC18F4525-I/PT, PIC18F4585-I/PT, PIC18F4610-I/P), and practical design notes that complement the 390-page Microchip datasheet.

詢價聯絡我們

PIC18F4620T-I/ML

PIC18F4620T-I/ML - 8-Bit 40MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F4620T-I/ML is an 8-bit PIC18F-family CMOS flash microcontroller delivering 40 MIPS performance at 40 MHz, with 64 KB of program Flash, 3968 bytes of SRAM, and 1024 bytes of EEPROM, housed in a 44-pin QFN (ML) 8x8 mm package. It offers 36 digital I/O lines, a 10-bit A/D converter with up to 13 input channels, multiple serial peripherals (USART, MSSP for SPI/I2C), and nanoWatt power management for energy-efficient designs. A PIC18 microcontroller is an 8-bit RISC-architecture MCU from Microchip's PIC18 family that combines Harvard bus architecture with a 16-bit instruction word, sitting in the broader taxonomy of microcontroller -> embedded MCU -> 8-bit MCU -> CMOS flash MCU -> semiconductor. The PIC18F4620 sits at the upper end of the original PIC18F46xx family, providing more memory and I/O than the PIC18F4520 while sharing the same peripheral set for code reuse. Key features include 64 KB self-programmable Flash (32K x 16), 3968 bytes SRAM, 1024 bytes EEPROM, 40 MHz maximum clock (10 MIPS at 10 MHz / 40 MIPS at 40 MHz), 36 I/O pins with individual direction control, an Enhanced Capture/Compare/PWM (ECCP) module, two CCP modules, a 10-bit ADC with 13 channels and 100K samples/sec, two analog comparators, and a USART with RS-485 support. The 'T' suffix denotes tape-and-reel packaging, the 'I' indicates the -40C to +85C industrial temperature grade, and 'ML' specifies the 44-pin QFN. The PIC18F4620T-I/ML uses a modified Harvard architecture with separate program and data buses, a hardware multiplier for 8x8 single-cycle instructions, and nanoWatt technology that allows multiple power-managed modes (Idle, Sleep, Doze) for battery-powered and always-on applications. The wide 2.0V to 5.5V operating range (industrial grade, with F variant limited to 4.2-5.5V) supports both 3.3V and 5V designs. Typical applications include industrial control and automation, USB interface adapters (with external MCU-side firmware stack), home appliances, sensor hubs, automotive body controllers (non-AEC-Q100), and consumer electronics requiring moderate computational load with low power draw. Common development tools include MPLAB X IDE, MPLAB XC8 compiler, and PICkit 3/4/5 in-circuit debuggers. When designing with this part, allocate at least 1.0 square inch of PCB copper beneath the QFN thermal pad to meet the 31.5 C/W theta_JA dissipation budget; enable the internal voltage regulator (PIC18F4620 includes an LDO) but always place a 100 nF + 10 uF decoupling pair within 3 mm of each VDD/VSS pair. For bare-metal designs, the device's vectored interrupt controller requires the IVT to be aligned to the 0x000018 boundary. This page combines distributor pricing, parametric specifications, and engineering design notes - information not consolidated on any single distributor or manufacturer page.

詢價聯絡我們

PIC18F4680-E/ML

PIC18F4680-E/ML - 8-bit 25MHz 64KB Flash MCU w/ECAN | Microchip

The Microchip Technology PIC18F4680-E/ML is an 8-bit PIC18 RISC flash microcontroller integrating 64KB (32K x 16) of program Flash, 3,328 bytes of SRAM, and 1,024 bytes of data EEPROM into a 44-pin QFN (8x8 mm) package with an exposed thermal pad. It supports up to 40 MHz external clock operation (10 MIPS) across a 4.2V to 5.5V supply range, integrates an ECAN module compliant with CAN 2.0B active/passive, and carries nanoWatt power management peripherals for battery-friendly designs. What is a microcontroller? A microcontroller is a compact programmable processor that integrates a CPU, non-volatile program memory (Flash or ROM), volatile data memory (RAM), and configurable peripheral modules onto a single silicon die. Within the broader taxonomy, a microcontroller sits below a microprocessor (which generally requires external memory and peripherals) and above a digital signal controller. The 8-bit PIC18 family specifically targets deterministic real-time embedded control with an enhanced 16-bit instruction word, hardware 8x8 multiplier, and nanoWatt power management. The 8-bit PIC18F4680 is engineered for CAN-bus nodes, automotive body controllers, and industrial sensor networks where deterministic timing and on-chip communication peripherals reduce external component count. Key features of the PIC18F4680-E/ML include an integrated ECAN (Enhanced Controller Area Network) module with hardware acceptance filtering and standard/extended identifier support, a 10-bit ADC with up to 11 input channels, an enhanced USART with LIN master/slave capability, a Master Synchronous Serial Port (MSSP) configurable for SPI or I2C (master/slave), two analog comparators, a programmable 16-level low-voltage detect (LVD), and nanoWatt power-saving modes such as Run, Idle, and Sleep with multiple wake-up sources. The 64KB of self-programmable Flash supports in-application updates via ICSP, enabling firmware revision without removing the MCU from the board. The PIC18F4680-E/ML uses Microchip's enhanced Harvard architecture: separate program and data buses feeding a 16-bit instruction word and an 8-bit data path provide deterministic single-cycle instruction timing, ideal for hard real-time control loops. The integrated ECAN module offloads CAN message filtering and buffering from the CPU; the MSSP allows simultaneous SPI/I2C peripheral connectivity; and nanoWatt technology provides idle and sleep currents in the microamp range for automotive quiescent requirements. The combination of these peripherals positions the PIC18F4680 as a CAN-bus hub MCU bridging LIN sub-buses and SPI sensor front ends. Typical applications include automotive body and chassis ECAN nodes (door modules, lighting, HVAC actuators), industrial CAN-bus sensor and actuator networks, building automation gateways using CAN as the backbone bus, and LIN-bus peripherals in automotive instrument clusters. The combination of ECAN, LIN-capable USART, and MSSP allows a single MCU to bridge multiple automotive and industrial communication buses. When laying out the PCB, connect the exposed thermal pad on the underside of the QFN-44 package directly to the ground plane for both electrical grounding and thermal dissipation. The -E suffix indicates the extended operating temperature range of -40C to +125C, suitable for automotive underhood and industrial environments. Provide a 100 nF decoupling capacitor adjacent to each VDD pin and a bulk capacitor close to the IC, and respect the MCLR reset line trace length guidelines documented in the Microchip PIC18F family reference manual. This page synthesizes distributor pricing, drop-in alternatives from the PIC18 family, and practical design notes not found on a single distributor product page, providing a one-stop engineering reference for selecting the PIC18F4680-E/ML in new designs or as a drop-in upgrade path.

詢價聯絡我們

PIC18F4680-H/P

PIC18F4680-H/P - 8-bit MCU, 64KB Flash, ECAN, PDIP-40 | Microchip

The Microchip Technology PIC18F4680-H/P is an 8-bit PIC18 family microcontroller with 64 KB of Flash program memory, 3328 bytes of RAM, and an integrated Enhanced CAN (ECAN) module, housed in a 40-pin PDIP through-hole package. It operates from a 4.2 V to 5.5 V supply, runs at up to 40 MHz internal clock (25 MIPS at 5 V), and provides 36 digital I/O lines plus a 10-bit ADC. The '-H/' temperature grade extends the operating range to 150 °C, targeting high-temperature automotive under-hood and industrial environments. What is a PIC18 8-bit microcontroller? A PIC18F-series MCU is a Harvard-architecture RISC microcontroller from Microchip, belonging to the broader PIC microcontroller family within the 8-bit microcontrollers category. It executes one instruction per clock cycle (four clocks per instruction) and uses separate program and data buses, which lets the CPU fetch the next instruction while reading data. PIC18 devices add 16-bit instructions, a hardware multiplier, and a linear program/data memory map, making them suitable for embedded control, motor drive, and CAN-connected automotive/industrial networks where deterministic real-time response is required. Key features of the PIC18F4680-H/P include 64 KB (32K x 16) of self-programmable Flash, 3328 bytes of data SRAM, 1024 bytes of EEPROM, an ECAN controller compliant with CAN 2.0B (up to 1 Mbps), two enhanced USART modules, two MSSP (SPI/I2C) peripherals, a 10-bit ADC with up to 11 channels, and nanoWatt power management for low-current sleep states. Three 16-bit timers/counters plus a watchdog timer and hardware ECCON-protected Flash access are also integrated. The device is built on Microchip's enhanced flash process and uses the standard PIC18 instruction set, which simplifies migration across the family. The integrated ECAN module supports DeviceNet, CANopen, and J1939-style networks with hardware filtering, freeing the CPU from bit-banging the CAN protocol. Combined with 25 MIPS throughput and 64 KB code space, this enables gateways, sensor nodes, and motion-control peripherals to run full protocol stacks alongside application logic. Typical applications include CAN-connected automotive body and chassis ECUs, industrial sensor hubs and motor-control peripherals, building-automation gateways, and IEC 61131-3-free programmable logic controllers. The wide 4.2 V to 5.5 V range and -40 °C to +150 °C operating envelope also make the device usable in solar inverters, oil/gas downhole telemetry, and heavy-equipment instrumentation. When designing with this MCU, allocate decoupling per datasheet guidelines (typically 100 nF plus 10 uF bulk) close to VDD/AVDD pins, and connect the ECAN TX/RX pins through a CAN transceiver such as the MCP2551 or MCP2561 - the ECAN module does not include bus-side drivers. Use MPLAB XC8 or the legacy C18 compiler for firmware development with MPLAB X IDE and a PICkit 5 or ICD 5 programmer. This page synthesizes distributor pricing, drop-in alternative MPNs, application notes, and design considerations not bundled in the manufacturer datasheet itself, giving procurement and firmware engineers a one-stop reference.

詢價聯絡我們

PIC18F4680-H/PT

PIC18F4680-H/PT - 8-bit MCU, 64KB Flash, ECAN, 44-TQFP | Microchip

The Microchip PIC18F4680-H/PT is a high-performance 8-bit RISC microcontroller with 64KB Flash, 3,328 bytes of SRAM, 1,024 bytes of Data EEPROM, and integrated ECAN (CAN 2.0B active) controller, packaged in a 44-pin TQFP (10x10 mm). It operates up to 25 MHz (40 MHz maximum input), delivers 10 MIPS, integrates a 10-bit ADC, two USART modules (with LIN support), and supports the nanoWatt power-management feature set for low-power embedded designs. What is a PIC18F Microcontroller? The PIC18F family is Microchip's 8-bit enhanced RISC architecture for general-purpose embedded control. PIC18F devices sit within the broader taxonomy: 8-bit MCU -> Harvard RISC microcontroller -> PIC family -> PIC18F sub-family -> semiconductor. They offer 16-bit instruction words, 8-bit data paths, hardware multiplier, prioritized interrupts, and Flash self-programming, making them the standard workhorse for industrial, automotive, and consumer applications that need deterministic real-time control without the complexity of an ARM Cortex core. Key features of the PIC18F4680-H/PT include: 64KB Flash program memory (32K x 16), 3,328 bytes SRAM, 1,024 bytes Data EEPROM with high-endurance Flash (HEF) option, integrated ECAN module (CAN 2.0B active with three transmit and two receive buffers), two USART modules with LIN-compatible master/slave operation, MSSP (SPI/I2C), 10-bit ADC with up to 13 input channels, nanoWatt power-managed modes (Idle, Sleep, Deep Sleep, and Run), and a wide 2.0V-5.5V operating voltage range. The H temperature grade extends -40C to +150C. The architecture uses a 16-bit enhanced instruction set optimized for C-compiled code (MPLAB XC8 and legacy MPLAB C18), with 83 instructions and a hardware 8x8 multiplier. The ECAN peripheral implements CAN 2.0B active with hardware acceptance filters, time-stamping, and DeviceNet/CanOpen-friendly bit-timing configuration. With self-programmability and 100K/1M write-endurance ratings, field firmware upgrades are supported via ECAN or USART bootloader patterns common in automotive body and industrial control modules. Typical applications include automotive body and chassis ECAN nodes (cluster, HVAC, lighting controllers), industrial CAN-based sensor networks (DeviceNet, CANopen), HVAC controls, embedded control boards requiring LIN master support, and battery chargers using the ADC plus ECAN for cell-balancing feedback loops. When designing with this part, plan for a 2.0V-5.5V supply, ensure the ECAN bus transceivers (e.g. MCP2551 or MCP2561) match the bus topology, and provide sufficient decoupling. Use MPLAB X IDE with MPLAB ICD 5 or MPLAB PICkit 5 for in-circuit debug and Flash programming. This page consolidates verified distributor pricing, drop-in alternate MPNs sourced from Microchip's cross-reference, and PCB-level design notes not duplicated on the manufacturer summary page.

詢價聯絡我們

子分類

產品（39,000+)

PIC18F45Q10-I/P - 32KB Flash 8-bit MCU 64MHz 40-PDIP | Microchip

PIC18F45Q10-I/PT - 32KB Flash 8-bit MCU, 64MHz, 44-TQFP

PIC18F45Q10T-I/MP - 32KB Flash 8-bit MCU, 64MHz, 40-QFN | Microchip

PIC18F45Q10T-I/PT - 8-bit 64MHz MCU, 32KB Flash, 44-TQFP | Microchip

PIC18F45Q43-E/P - 64MHz 8-Bit MCU, 32KB Flash, 40-PDIP | Microchip

PIC18F45Q43-I/MP - 8-bit 64MHz 32KB Flash XLP MCU | Microchip

PIC18F45Q43-I/P - 8-Bit 64MHz 32KB Flash MCU 40-PDIP | Microchip

PIC18F45Q43-I/PT - 8-Bit 64MHz 32KB Flash MCU | Microchip

PIC18F45Q43T-I/MP - 8-bit MCU, 32KB Flash, 64MHz | Microchip

PIC18F4610-E/ML - 8-bit MCU, 64KB Flash, 44-QFN | Microchip

PIC18F4610-E/P - 8-bit MCU, 64KB Flash, 40MHz, 40-PDIP | Microchip

PIC18F4610-E/PT - 8-Bit 25MHz MCU 64KB Flash 44-TQFP | Microchip

PIC18F4610-I/P - 8-Bit 40MHz 64KB Flash MCU 40-PDIP | Microchip

PIC18F4610-I/PT - 8-bit 40MHz 64KB Flash MCU | Microchip

PIC18F4610T-I/PT - 64KB Flash 8-bit MCU | Microchip | TQFP-44

PIC18F4620-E/ML - 8-Bit 40MHz MCU 64KB Flash | Microchip

PIC18F4620-E/P - 8-bit MCU 64KB Flash 40MHz 40-DIP | Microchip

PIC18F4620-E/PT - 8-Bit 25MHz 64KB Flash MCU 44-TQFP | Microchip

PIC18F4620-I/P - 8-Bit 40MHz 64KB Flash MCU 40-PDIP | Microchip

PIC18F4620-I/PT - 8-Bit 40MHz PIC MCU, 64KB Flash, 44-TQFP | Microchip

PIC18F4620T-I/ML - 8-Bit 40MHz 64KB Flash MCU | Microchip

PIC18F4680-E/ML - 8-bit 25MHz 64KB Flash MCU w/ECAN | Microchip

PIC18F4680-H/P - 8-bit MCU, 64KB Flash, ECAN, PDIP-40 | Microchip

PIC18F4680-H/PT - 8-bit MCU, 64KB Flash, ECAN, 44-TQFP | Microchip