積體電路

子分類

📁 ADC/DAC 3,100+ 產品 📁 放大器 IC 1,900+ 產品 📁 音訊編解碼器 18 產品 📁 音訊 IC 2 產品 📁 時脈與計時 660+ 產品 📁 Comparator ICs 1 產品 📁 DSP 1,100+ 產品 📁 資料擷取 IC 2 產品 📁 數位電位器 4 產品 📁 顯示驅動器與控制器 1 產品 📁 FPGA 與 CPLD 7,300+ 產品 📁 介面 IC 3,300+ 產品 📁 LED 驅動器 1 產品 📁 邏輯 IC 460+ 產品 📁 記憶體 IC 870+ 產品 📁 微控制器 20,000+ 產品 📁 微處理器 4 產品 📁 馬達驅動器 1 產品 📁 其他 1 產品 📁 感測器與偵測器介面 1 產品 📁 特殊用途 IC 15 產品 📁 視訊 IC 14 產品

產品（39,000+)

PIC24FJ512GU405-I/PT - 16-bit MCU 512KB Flash USB/LCD 48-TQFP | Microchip
PIC24FJ512GU405-I/PT

PIC24FJ512GU405-I/PT - 16-bit MCU 512KB Flash USB/LCD 48-TQFP | Microchip

The Microchip PIC24FJ512GU405-I/PT is a 16-bit PIC24F microcontroller integrating 512 KB of ECC Flash, 32 KB SRAM, full-speed USB 2.0, an LCD controller, and a rich set of Core Independent Peripherals (CIPs) in a 48-pin TQFP (7x7 mm) package. It executes instructions at 16 MIPS from a 32 MHz system clock derived from an internal 8 MHz FRC with PLL, supporting industrial temperature range (-40C to +85C). A 16-bit microcontroller (MCU) is a microprocessor core that processes data in 16-bit-wide chunks, balancing 8-bit simplicity with 32-bit performance. It belongs to the taxonomy: microcontroller -> embedded MCU -> 16-bit MCU -> RISC MCU -> semiconductor. PIC24F devices specifically target ultra-low-power (eXtreme Low Power) applications, making them well-suited to battery-powered and energy-harvesting designs. Key features of the PIC24FJ512GU405 include dual-partition Flash supporting real-time Over-The-Air (OTA) firmware updates and EEPROM emulation without external components, eliminating in-field firmware-update downtime. Integrated peripherals include a 12-bit ADC, multiple UART/SPI/I2C, Real-Time Clock, comparators, PWM, and a segmented LCD driver. The full-speed USB 2.0 device controller enables tethered or self-powered connected-product designs without an external transceiver. The device uses a Harvard RISC architecture with modified Harvard memory mapping, achieving deterministic 32 MHz operation with deep-sleep currents in the microamp range. Core Independent Peripherals handle tasks like signal conditioning, waveform generation, and event-based sequencing without CPU wake-ups, dramatically reducing average power. Typical applications include IoT sensor nodes with LCD displays, USB-connected industrial data loggers, secure OTA-updatable consumer appliances, low-power medical monitoring, and remote-control human-machine interfaces requiring segmented LCD readouts. The dual-partition OTA capability is critical for products that must update firmware without service interruption. When designing with this part, allocate sufficient decoupling (100 nF + bulk) near each VDD/VSS pair, keep the 48-pin TQFP PCB layout symmetrical, and reserve a programming/debug footprint for the 4-wire ICSP interface. Pay attention to the USB D+/D- trace impedance (90 ohm differential) for FCC compliance. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and PCB design notes that go beyond what the manufacturer datasheet or distributor catalog pages typically surface in one place.

詢價 聯絡我們
PIC24FJ512GU405T-I/M4 - 512KB Flash USB MCU | Microchip | 48-UQFN
PIC24FJ512GU405T-I/M4

PIC24FJ512GU405T-I/M4 - 512KB Flash USB MCU | Microchip | 48-UQFN

The Microchip PIC24FJ512GU405T-I/M4 is a 16-bit PIC microcontroller from the PIC24F eXtreme Low-Power family, featuring 512KB dual-partition Flash, 32KB RAM, full-speed USB, and an integrated LCD controller, housed in a 48-pin UQFN (6x6 mm) package with exposed pad. It operates up to 32MHz (16 MIPS) from a 2.0V to 3.6V supply across an industrial -40C to +85C temperature range, and is supplied on tape and reel ("T" suffix) for high-volume SMT assembly. A 16-bit microcontroller (MCU) is a programmable embedded processor that balances 8-bit simplicity with 32-bit performance. The PIC24FJ sits in the hierarchy: microcontroller -> 16-bit MCU -> PIC24F -> eXtreme Low-Power PIC -> PIC24FJ GU4/GL4 family. Compared with 8-bit MCUs, 16-bit PICs deliver wider datapaths, more RAM, richer peripherals and DMA, while keeping a streamlined instruction set optimized for C and assembly. The PIC24FJ series in particular emphasizes low active and sleep current for battery-powered products. Key features include 512KB dual-partition Flash supporting real-time Over-The-Air (OTA) updates and EEPROM emulation, 32KB SRAM, hardware crypto engine, USB 2.0 full-speed (Host/Device/OTG), up to 39 I/O pins, and a segmented LCD controller with charge pump. Core-independent peripherals (CIPs) such as configurable logic cells, CLC, MCCP/SCCP, 16-bit timers, and 12-bit ADC reduce CPU burden and enable event-driven design. The dual-partition Flash lets the firmware swap between two images during OTA, eliminating external bootloader memory. Architecturally, the PIC24FJ GU4 family uses a modified Harvard architecture with a 16-bit datapath, hardware multiply/divide, and dedicated DMA to peripherals. The dual-partition Flash controller supports live firmware updates by remapping the active partition, while the segmented LCD driver with integrated charge pump drives up to 8 commons and 48 segments without external bias resistors, simplifying low-power HMIs. Typical applications include USB-enabled IoT nodes with OTA firmware updates, battery-powered industrial HMIs with segmented LCD, secure connected sensors with hardware crypto, and USB HID peripherals such as data loggers and human-interface devices. The wide Flash and RAM budget also supports medical device accessories and asset-tracking tags. Designers favor this part when they need USB, an LCD, and OTA updates in a single low-pin-count QFN. When designing with this part, plan Flash partitions for A/B image swap to enable robust OTA recovery and reserve one erase-block for EEPROM emulation rather than wearing the main image. The 6x6 mm UQFN has an exposed thermal pad that must be soldered to a continuous ground plane for thermal and signal-integrity performance; do not route signal traces under the EP. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-package Microchip family variants, cross-package guidance, and verified parametric proximity data.

詢價 聯絡我們
PIC24FJ512GU406-E/MR - 16-bit MCU 512KB Flash USB LCD 64-QFN
PIC24FJ512GU406-E/MR

PIC24FJ512GU406-E/MR - 16-bit MCU 512KB Flash USB LCD 64-QFN

The Microchip Technology PIC24FJ512GU406-E/MR is a 16-bit microcontroller from the PIC24F 'GU4/GL4' family with 512KB ECC Flash, 32KB RAM, integrated full-speed USB, and an LCD driver, housed in a 64-pin QFN (9x9 mm) package with extended operating temperature range (-40C to +125C). Key features include a 16-bit modified Harvard CPU core running at 32 MHz (16 MIPS) with single-cycle multiply and divide, dual-partition flash supporting real-time Over-The-Air (OTA) firmware updates, EEPROM emulation, a segmented LCD driver with up to 64 segments, full-speed USB 2.0 with device/host/OTG capability, and multiple Core Independent Peripherals (CIPs) such as configurable logic cells, 16-bit PWMs, and a 12-bit ADC. The PIC24FJ512GU406 family also integrates a hardware crypto engine, a real-time clock and calendar (RTCC) with VBAT backup, a charge time measurement unit (CTMU) for touch sensing, and 53 general-purpose I/O pins grouped across multiple ports (RA/RB/RC/RD/RF/RG). 2V to 3.6V single-supply operation and multiple low-power sleep modes (Doze, Idle, Sleep, Deep Sleep) target battery-powered designs. Typical applications include industrial control panels with segmented LCDs, USB peripherals and embedded host devices, IoT edge nodes requiring OTA firmware updates, medical instrumentation displays, automotive body and HVAC control modules, and consumer appliances with touch and graphical segmented UIs. The 'GU' parts add the LCD driver; the 'GL' sister family parts in the same QFN-64 footprint omit USB for cost-sensitive versions. The 'E' suffix indicates an extended temperature grade (-40C to +125C) suitable for automotive and industrial environments. Always select AEC-Q100 qualified variants for safety-relevant automotive ECUs. This page consolidates distributor pricing, parametric depth, application guidance, and pin-compatible alternatives in a single datasheet-context view, intended to shorten the BOM decision cycle for engineers evaluating the PIC24FJ512GU406-E/MR against other members of the PIC24FJ 'GU/GL' family and against competing 16-bit MCUs.

詢價 聯絡我們
PIC24FJ512GU406-E/PT - 16-Bit MCU, 512KB Flash, USB, LCD | Microchip
PIC24FJ512GU406-E/PT

PIC24FJ512GU406-E/PT - 16-Bit MCU, 512KB Flash, USB, LCD | Microchip

The Microchip Technology PIC24FJ512GU406-E/PT is a 16-bit PIC microcontroller from the PIC24FJ 'GU4' family, delivering 16 MIPS at 32 MHz with 512 KB of dual-partition ECC Flash, 32 KB of RAM, and integrated full-speed USB plus segment LCD driver. Housed in a 64-pin TQFP (10x10 mm) package, the 'E' suffix denotes the extended (-40C to +125C) operating-temperature grade and the /PT suffix denotes the TQFP package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of on-chip peripherals such as timers, communication controllers, ADCs, and GPIOs. PIC24FJ MCUs belong to the broader 16-bit MCU family, sitting architecturally above 8-bit PIC16/PIC18 parts and below 32-bit Cortex-M devices in the Microchip portfolio, and they are commonly used in cost-sensitive, low-power embedded applications. Key features of the PIC24FJ512GU406-E/PT include 512 KB of dual-partition Flash that supports live Over-The-Air (OTA) firmware updates without device downtime, hardware EEPROM emulation, and 32 KB of RAM. The 'GU' family also adds Core Independent Peripherals (CIPs) such as CLC, PWM, capture, and a 12-bit ADC, while the integrated LCD driver supports segmented displays and the on-chip USB 2.0 full-speed controller eliminates an external PHY. Power-management features include multiple Idle, Sleep, and Doze modes that allow extended battery life in always-on products. Typical applications for the PIC24FJ512GU406-E/PT include industrial HMI panels with segmented LCDs, USB-connected sensor hubs, automotive body and cluster subsystems, home appliances with LCD user interfaces, low-power IoT edge nodes that require OTA firmware maintenance, and medical handhelds where 16-bit math and segment-LCD drives coexist. The wide -40C to +125C operating range and AEC-Q100 qualification make the 'E' grade suitable for automotive under-hood and industrial environments. When designing with this device, confirm that the 64-pin TQFP pad pattern is acceptable for the PCB footprint library and that the USB D+/D- pins are routed with 90 ohm differential impedance. Programmers should use MPLAB X IDE with the XC16 compiler, and the dual-partition Flash layout must be configured through the device configuration bits before live OTA updates are enabled. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC24FJ 'GU/GL' families, and practical design notes not collated in the manufacturer datasheet.

詢價 聯絡我們
PIC24FJ512GU406-I/MR - 512KB Flash 16-bit MCU USB LCD | Microchip
PIC24FJ512GU406-I/MR

PIC24FJ512GU406-I/MR - 512KB Flash 16-bit MCU USB LCD | Microchip

The Microchip Technology PIC24FJ512GU406-I/MR is a 16-bit microcontroller from the PIC24F family featuring 512KB of dual-partition Flash, 32KB RAM, full-speed USB 2.0, segmented LCD driver, and a 16 MIPS CPU core running up to 32 MHz, all housed in a 64-pin QFN (MR) package measuring 9x9 mm. The dual-partition Flash architecture supports real-time Over-The-Air (OTA) firmware updates and EEPROM emulation, enabling firmware upgrades without application downtime - a critical feature for connected embedded products. A 16-bit microcontroller (MCU) is an integrated circuit containing a CPU, memory, and programmable peripherals on a single die. The 16-bit data path allows single-cycle arithmetic on integer values up to 65,535, balancing performance and code density between 8-bit (e.g., PIC16, AVR) and 32-bit (e.g., Cortex-M) architectures. The PIC24F family is Microchip's low-power 16-bit line, positioned above PIC16/PIC18 8-bit parts and below dsPIC/PIC32 32-bit offerings in the company's portfolio hierarchy. Key features include 16 MIPS performance at 32 MHz, multiple Core Independent Peripherals (CIPs) that operate without CPU intervention, a 12-bit ADC, multiple UART/SPI/I2C interfaces, and a segmented LCD driver supporting up to 512 segments. The 512KB ECC Flash and 32KB SRAM provide ample headroom for USB stacks, LCD UI assets, and OTA update buffers. Wide operating voltage (2.0V to 3.6V) and low-power sleep modes with RTC retention make this MCU well-suited to battery-powered applications. Architecturally, the PIC24FJ GU4/GL4 family combines a modified Harvard architecture with a 16-bit instruction word and 24-bit instruction bus. The dual-partition Flash divides memory into two independent 256KB regions, allowing one partition to execute application code while the other receives a firmware update, then swap roles atomically for true live update capability. Core Independent Peripherals (CIPs) like CLC, MCCP, and DMA operate autonomously, freeing the CPU from routine tasks. Typical applications include USB Human Interface Devices (HIDs) with integrated LCD displays, industrial control panels with segmented LCD readouts, medical devices requiring secure OTA firmware updates, IoT edge nodes with sensor readouts, and consumer appliances with graphical segment displays. The combination of USB, LCD, and OTA in a single part eliminates 15-200 external components typically required by separate parts. When designing with this device, allocate one Flash partition for the bootloader and one for application code from project start - retrofitting OTA support after firmware development is significantly harder. Ensure the 64-pin QFN ground pad is soldered with adequate thermal vias; pin pitch is 0.5 mm, requiring precise stencil design for reliable assembly. This page synthesizes distributor pricing, drop-in alternative PIC24F family members, parametric comparisons, and practical design notes not consolidated on the manufacturer datasheet or individual distributor pages.

詢價 聯絡我們
PIC24FJ512GU406-I/PT - 16-Bit 32MHz 512KB Flash MCU with USB & LCD | Microchip
PIC24FJ512GU406-I/PT

PIC24FJ512GU406-I/PT - 16-Bit 32MHz 512KB Flash MCU with USB & LCD | Microchip

The Microchip Technology PIC24FJ512GU406-I/PT is a 16-bit microcontroller IC from the PIC® 24F family, featuring a 32MHz CPU core (16 MIPS), 512KB ECC Flash with Dual Partition for live OTA updates, and 32KB SRAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates a full-speed USB 2.0 peripheral, a segmented LCD controller, and a rich set of Core Independent Peripherals (CIPs) for offloading tasks from the CPU. The 'I' suffix indicates the industrial -40C to +85C operating temperature range. A 16-bit microcontroller (MCU) is a microprocessor with a 16-bit data path, ALU, and registers, offering higher code density, faster arithmetic, and richer peripheral integration than 8-bit MCUs while remaining simpler and lower-power than 32-bit Cortex-M devices. Within the embedded hierarchy, MCUs belong to microcontrollers, which sit under microprocessors, which are subclasses of semiconductor ICs. The PIC24F 'J' series specifically targets ultra-low-power applications with nanoWatt sleep modes and operates from a 2.0V to 3.6V supply, suiting battery-powered and energy-harvesting designs. Key features include up to 512KB self-programmable Flash with Error-Correcting Code (ECC) and live Dual Partition OTA update support, 32KB SRAM, hardware Real-Time Clock and Calendar (RTCC), 10-bit and 12-bit ADC modules, multiple UART/SPI/I2C peripherals, and segmented LCD driver capable of driving up to 60 segments (PT package). The 64-pin TQFP-64 (10x10) provides ample I/O with extensive remappable peripherals via PPS (Peripheral Pin Select). The architecture is built on a modified Harvard structure with 16-bit instructions and a 24-bit instruction word, enabling compact code and deterministic interrupt response. ECC-protected Flash significantly improves reliability in industrial and consumer applications subject to soft-error upset, while the dual-partition Flash scheme allows background firmware updates with atomic rollback on failure - a critical feature for IoT and connected devices that cannot tolerate bricked field units. Typical applications include USB-enabled IoT sensor hubs, low-power medical monitoring devices with LCD readouts, industrial HMI panels with segmented displays, battery-powered data loggers, and consumer appliances with USB diagnostics or firmware update capability. The combination of integrated LCD and USB in a single MCU eliminates external drivers and bridges, reducing BOM and PCB area. When designing with this device, pay careful attention to decoupling: place 100nF ceramic capacitors as close as possible to every VDD/VSS pair and a bulk 4.7uF to 10uF tantalum or ceramic near the package. The USB DP/DM traces require 90-ohm differential impedance and a precision full-speed USB pull-up resistor on D+; for robust USB-IF compliance, refer to Microchip application note AN1227. SegLCD bias generation can be routed through internal charge pump or external resistor ladder - verify contrast across the full -40C to +85C temperature range. This page synthesizes distributor pricing, drop-in compatible PIC24FJ family alternatives, and practical design notes not found in the manufacturer datasheet alone, providing an engineering decision aid beyond raw specifications.

詢價 聯絡我們
PIC24FJ512GU406T-I/PT - 512KB Flash, USB, 16-bit MCU | Microchip
PIC24FJ512GU406T-I/PT

PIC24FJ512GU406T-I/PT - 512KB Flash, USB, 16-bit MCU | Microchip

The Microchip Technology PIC24FJ512GU406T-I/PT is a 16-bit PIC24F microcontroller featuring 512 KB of dual-partition Flash, 32 KB RAM, a full-speed USB 2.0 device/host/OTG controller, and an integrated segmented LCD driver, all housed in a 64-pin TQFP (10x10 mm) package. It operates at up to 32 MHz (16 MIPS) across a 2.0V to 3.6V supply range, and includes Core Independent Peripherals (CIPs) such as CLC, MCCP/SCCP, RTCC, and a 24-channel 12-bit A/D converter. The dual-partition Flash architecture supports real-time Over-The-Air (OTA) firmware updates and EEPROM emulation, enabling field-deployable code updates and parameter storage without external memory. The device carries 53 digital I/O pins and is qualified to AEC-Q100 Grade 1 for automotive embedded applications. CIPs handle deterministic tasks like waveform generation, signal conditioning, and event-triggered ADC conversions in hardware, freeing the CPU for application code. Typical applications include automotive instrument clusters and HVAC controls, USB-connected industrial sensors, consumer human-interface devices with segmented LCDs, secure IoT nodes requiring OTA firmware updates, and battery-powered medical monitors. Real-time OTA updates allow secure bootloader-style firmware replacement without service interruption, while ECC Flash preserves data integrity. When designing, pair the device with a 32.768 kHz crystal on SOSCO/SOSCI for RTCC operation, place decoupling capacitors within 5 mm of each VDD/VSS pair, and follow the PCB layout guidelines in the datasheet for USB DP/DN trace impedance to ensure USB-IF compliance.

詢價 聯絡我們
PIC24FJ512GU408-E/PT - 16-Bit 32MHz 512KB USB MCU | Microchip
PIC24FJ512GU408-E/PT

PIC24FJ512GU408-E/PT - 16-Bit 32MHz 512KB USB MCU | Microchip

The Microchip PIC24FJ512GU408-E/PT is a 16-bit microcontroller from the PIC24F 'GU4' family featuring a 32 MHz core, 512 KB of dual-partition Flash, 32 KB RAM, full-speed USB, an integrated segmented LCD controller, and 69 I/O pins, housed in an 80-pin TQFP (12x12 mm) package with -40C to +125C extended operating temperature. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral interfaces. The PIC24FJ 'GU4/GL4' family sits within Microchip's 16-bit eXtreme Low-Power MCU portfolio (a hypernym of: 16-bit MCU -> microcontroller -> embedded processor -> semiconductor) and targets battery-powered and human-interface applications that demand USB connectivity, segmented LCD drive, and field-upgradeable firmware. Key features of this part include 512 KB of Flash supporting real-time Over-The-Air (OTA) dual-partition updates and EEPROM emulation, a hardware Cryptographic Engine (CE) for AES/encryption acceleration, Core Independent Peripherals (CIPs) such as CLC, MCCP, and PTG, and a 16-channel 12-bit ADC with CTMU for touch and current measurement. The integrated segmented LCD controller supports up to 512 segments, eliminating external display driver ICs in HMI designs. Architecturally, the device uses a modified Harvard core with a 16-bit data path, 24-bit instruction word, and a 16-element working register array. USB 2.0 full-speed (12 Mbps) is provided on-chip with an internal transceiver and dedicated DMA, and the segmented LCD driver shares I/O pins with general-purpose digital I/O via configurable multiplexing. Deep sleep modes and an RTC with VBAT retention allow system-level quiescent currents under 1 uA. Typical applications include industrial HMI panels with LCD + USB service-port, USB-connected IoT edge nodes with OTA firmware, secure metering and access control with on-chip AES, and automotive-grade subsystems given the part's -E extended temperature grade and AEC-Q100 qualification noted on the distributor listing. When designing with this MCU, allocate careful pin planning between LCD segments and digital I/O early - the 80-pin TQFP exposes only 69 free I/O once LCD, USB, and debug pins are reserved. Use the dual-partition Flash feature with a verified bootloader to enable fail-safe OTA updates.

詢價 聯絡我們
PIC24FJ512GU408-I/PT - 16-bit 32MHz 512KB Flash MCU | Microchip
PIC24FJ512GU408-I/PT

PIC24FJ512GU408-I/PT - 16-bit 32MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC24FJ512GU408-I/PT is a 16-bit microcontroller from the PIC24F 'GU4/GL4' family, built on an eXtreme Low-Power architecture and housed in an 80-pin TQFP (12x12 mm) package. It integrates 512 KB of dual-partition Flash supporting real-time Over-The-Air (OTA) updates and EEPROM emulation, 32 KB of RAM, a full-speed USB 2.0 controller, an integrated segmented LCD controller, and a rich set of Core Independent Peripherals (CIPs). The CPU core runs up to 32 MHz (16 MIPS) and integrates hardware multiply/divide, a 17-bit x 17-bit single-cycle MAC, and a high-throughput instruction pipeline tuned for low-power operation. A 16-bit microcontroller is a single-chip computer that processes data 16 bits at a time, sitting between 8-bit MCUs (low cost, simple control) and 32-bit MCUs (high performance, complex OS). 16-bit PIC microcontrollers target mid-range embedded designs that need more computational headroom, larger memory maps, and richer peripherals than 8-bit parts, without the power and code-size overhead of Cortex-M class devices. The PIC24F 'eXtreme Low-Power' subfamily adds nanoWatt XLP sleep modes (as low as 20 nA in deep sleep) that approach the standby current of 8-bit PIC MCUs while preserving 16-bit DSP-class throughput. Key differentiating features of the PIC24FJ512GU408 include 512 KB dual-partition Flash (live field firmware updates with rollback), a 32 KB general-purpose SRAM, hardware crypto accelerators, an 8-channel hardware DMA, a 16-bit Sigma-Delta ADC path, up to 69 general-purpose I/O, a segmented LCD driver with charge pump supporting up to 480 segments, a USB 2.0 full-speed device/host/OTG controller, and a Real-Time Clock Calendar (RTCC) with battery backup. Five timers/capture/compare and multiple UART/SPI/I2C interfaces round out the peripheral set. The dual-partition Flash architecture is the headline feature for OTA designs: a new image can be written to the inactive partition while the active one continues running the application, then swapped on next reset with instant rollback capability. Typical applications include battery-powered IoT sensor nodes with USB firmware update ports, medical wearables requiring segmented LCD readouts, industrial HMI panels with USB diagnostics, and remote sensor telemetry where OTA firmware updates eliminate physical service calls. The integrated LCD controller, hardware USB, and eXtreme Low-Power sleep currents together make this part uniquely suited for sealed, battery-driven human-interface products. When designing with the PIC24FJ512GU408, verify VDD vs. VBAT domain routing carefully and place the 80-pin TQFP on a 4-layer PCB with a continuous ground plane under the exposed pad to meet thermal and EMI requirements. Use MPLAB X IDE with the XC16 compiler and MCC code configurator to take advantage of the integrated CIPs and shorten development time. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
PIC24FJ512GU410-E/PT - 512KB Flash USB LCD MCU | Microchip
PIC24FJ512GU410-E/PT

PIC24FJ512GU410-E/PT - 512KB Flash USB LCD MCU | Microchip

The Microchip Technology PIC24FJ512GU410-E/PT is a 16-bit PIC24F microcontroller with 512 KB ECC Flash, 32 KB RAM, full-speed USB 2.0, and an integrated LCD controller, housed in a 100-pin TQFP (PT) package measuring 12x12 mm. It executes instructions at up to 32 MHz (16 MIPS) and operates from 2.0 V to 3.6 V, making it suitable for battery-powered and USB-powered embedded designs. A 16-bit microcontroller (MCU) is a programmable processor with a 16-bit data path, instruction word, and register width. Within the embedded hierarchy it sits between 8-bit MCUs (lower cost, simpler peripherals) and 32-bit ARM Cortex-M MCUs (higher performance, richer ecosystems). The PIC24F family specifically targets ultra-low-power and mixed-signal applications, and the GU4/GL4 sub-family adds dual-partition Flash for live Over-The-Air (OTA) firmware updates without device downtime - a critical capability for connected products deployed in the field. Key features include 512 KB of ECC-protected Flash supporting Dual Partition / EEPROM Emulation, 32 KB SRAM, a 14-channel 12-bit ADC, four I2C, four SPI, and five UART peripherals, plus a hardware Cryptographic Engine (AES, DES, 3DES, SHA, MD5, and RNG). Core-independent peripherals (CIPs) such as Configurable Logic Cells (CLC), Multiple Output Capture/Compare/PWM, and a 32-bit Real-Time Clock Calendar enable event-driven designs that minimize CPU wake-ups and reduce average power consumption below 1 uA in Deep Sleep mode. The device's architecture combines a modified Harvard bus with a 16-bit instruction word and 24-bit instruction address space, giving a deterministic interrupt latency of 5 cycles. The full-speed USB 2.0 peripheral with integrated PHY supports HID, CDC, MSD, and Vendor classes without an external transceiver. The segmented LCD driver can directly control up to 480 pixels (8 commons x 60 segments) with internal charge pump and contrast bias generation, eliminating the need for an external LCD bias network. Typical applications include low-power IoT sensor nodes with OTA firmware update capability, USB HID human-interface devices (keyboards, mice, touch panels), medical devices such as glucose meters and infusion pumps, industrial HMI panels with integrated LCD, secure authentication tokens using the on-chip AES engine, and home automation controllers with segmented displays. The wide operating temperature range of -40C to +125C (E suffix indicates Extended temperature grade) also supports outdoor and industrial deployments. When designing with this device, allocate pin remapping carefully between the LCD segment bus and parallel master port functions - they share pins and cannot be used simultaneously. Ensure the dual-partition Flash bootloader (Boot-Secure mode) is provisioned before locking the configuration registers, and consider using the on-chip Crypto Engine to offload AES-256 from the CPU rather than implementing it in firmware. This page synthesizes DigiKey/Mouser pricing, drop-in TQFP-100 alternatives from the PIC24FJ family, and practical low-power design notes that go beyond the manufacturer datasheet.

詢價 聯絡我們
PIC24FJ512GU410-I/PT - 512KB Flash, USB, LCD 16-bit MCU | Microchip
PIC24FJ512GU410-I/PT

PIC24FJ512GU410-I/PT - 512KB Flash, USB, LCD 16-bit MCU | Microchip

The Microchip PIC24FJ512GU410-I/PT is a 16-bit eXtreme Low-Power microcontroller featuring 512 KB of dual-partition Flash, 32 KB SRAM, integrated full-speed USB 2.0 device/host/OTG, and an on-chip LCD controller, housed in a 100-pin TQFP (PT) package. It executes instructions at 32 MHz (16 MIPS) from the PIC24F core, and operates from 2.0 V to 3.6 V with five low-power modes including a low-voltage Sleep mode that keeps the RTCC alive from a separate LDO. A 16-bit microcontroller (MCU) is an embedded processor that fetches 16-bit instructions and operates on 8/16-bit data paths, balancing code density, deterministic interrupt latency, and richer peripherals over 8-bit cores. Within the broader taxonomy, the PIC24F belongs to the 16-bit MCU -> microcontroller -> embedded processor -> semiconductor family, and the PIC24FJ512GU410 specifically targets low-power, USB-enabled human-machine interface (HMI) designs with segment LCDs. Key features include 512 KB self-programmable Flash with dual-partition OTA updates and EEPROM emulation, 32 KB SRAM, a 10-bit 1 MSPS ADC, multiple UART/SPI/I2C peripherals, a Real-Time Clock/Calendar (RTCC), a DMA controller, and the segment LCD driver supporting up to 480 segments. The integrated USB 2.0 full-speed transceiver eliminates external PHY cost, while the DMA engine offloads peripheral-to-memory transfers for higher throughput. Typical applications include industrial segment-LCD HMI panels, USB sensor hubs, battery-powered metering with display, medical handheld instrumentation, and home-automation controllers requiring OTA firmware updates. The wide operating voltage range and low-power Sleep modes make it equally suited to line-powered and battery-backed designs where the LCD must remain visible while the core is dormant. When designing with this device, ensure VDD decoupling follows the manufacturer reference layout with 100 nF caps at every supply pin and a 10 µF bulk near the regulator. The dual-partition Flash enables bootloader-driven OTA updates without external memory, but designers must plan partition sizes and the live-update state machine before deployment. This page combines distributor pricing, drop-in alternatives, and practical design notes that are not aggregated in the manufacturer datasheet alone.

詢價 聯絡我們
PIC24FJ512GU410T-I/PT - 512KB Flash USB MCU 100-TQFP | Microchip
PIC24FJ512GU410T-I/PT

PIC24FJ512GU410T-I/PT - 512KB Flash USB MCU 100-TQFP | Microchip

The Microchip Technology PIC24FJ512GU410T-I/PT is a 16-bit eXtreme Low-Power PIC24F microcontroller featuring 512KB of dual-partition Flash, 32KB SRAM, full-speed USB, an integrated LCD controller, and a 32MHz (16 MIPS) CPU core. It ships in a 100-pin TQFP (PT) package rated for the industrial -40C to +85C temperature range, making it suitable for human-machine interfaces and connected battery-powered products. A 16-bit PIC microcontroller is a member of the microcontroller (MCU) family that uses a 16-bit modified Harvard data path, sitting between 8-bit AVR/PIC MCUs and 32-bit ARM Cortex-M devices. Within the MCU taxonomy, PIC24F parts belong to the "F" subfamily of the PIC24 family, characterized by eXtreme Low-Power (XLP) technology, integrated peripherals, and dual-partition Flash that supports live Over-The-Air (OTA) firmware updates and EEPROM emulation. Key differentiating features of the PIC24FJ512GU410T-I/PT include the 512KB dual-partition Flash (vs 256KB on smaller siblings), 32KB RAM, the full-speed USB 2.0 full-speed device/host/OTG peripheral, the segmented LCD driver (up to 512 segments), and a rich set of Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Multiple Capture/Compare/PWM, and a hardware crypto engine for selected family members. The 16 MIPS throughput from the 32MHz oscillator supports real-time USB, LCD refresh, and CIP processing in parallel without CPU intervention. Architecturally, the device uses Microchip's modified Harvard architecture with separate program Flash and data SRAM buses, a hardware multiply/divide unit, a 16x16-bit working register array, and a peripheral bus that decouples I/O from the core for predictable interrupt latency. The dual-partition Flash allows one partition to run application code while the other receives an OTA image, then the bootloader atomically swaps roles, eliminating firmware-update downtime in connected sensor and metering products. Typical applications include USB-connected sensor hubs, industrial HMI panels with LCD displays, medical handheld instruments, home-automation gateways, and battery-powered IoT endpoints requiring OTA firmware maintenance. The wide operating voltage range and integrated LCD make it a strong fit for segment-LCD user interfaces in metering, appliance, and instrumentation products. When designing with this MCU, plan the dual-partition layout, ensure the USB bus is correctly terminated (D+/D- with 15kohm pulldown on D- for full-speed device mode), and place the decoupling capacitors within 5mm of each VDD/VSS pair to keep the eXtreme Low-Power modes stable. The PIC24FJ512GU410T-I/PT is the -40C to +85C industrial variant in 100-TQFP; for the 100C extended-temperature option, choose the PIC24FJ512GU410T-E/PT suffix. This page consolidates distributor pricing, parametric comparison with same-family siblings, cross-brand drop-in alternatives, and design notes that go beyond what the manufacturer datasheet alone provides.

詢價 聯絡我們
PIC24FJ64GA002-E/ML - 16-bit 32MHz 64KB Flash MCU | Microchip
PIC24FJ64GA002-E/ML

PIC24FJ64GA002-E/ML - 16-bit 32MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC24FJ64GA002-E/ML is a 16-bit PIC24F microcontroller running at 32 MHz with 64 KB Flash (22K x 24 words), 8 KB RAM, and a 28-pin QFN (6x6 mm) package. It integrates nanoWatt XLP extreme-low-power technology and delivers up to 16 MIPS performance from its modified Harvard architecture, including a 17-bit hardware multiplier and 16-bit hardware divider. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and a rich set of peripherals on a single die, forming the lowest tier of the embedded system hierarchy alongside sensors, power management, and connectivity ICs. The PIC24F family sits between the 8-bit PIC16/PIC18 and the 32-bit PIC32MX/PIC32MZ families, targeting applications that need more performance than 8-bit can deliver but do not justify the cost of a 32-bit core. Key features include 16 MIPS operation at 32 MHz, 8 MHz internal oscillator with 4x PLL and multiple divide options, on-chip 64 KB Flash program memory, 8 KB SRAM, and the nanoWatt XLP power-management modes that drop quiescent current below 1 uA in sleep. The 28-pin QFN exposes up to 21 general-purpose I/O, two analog comparators, a 10/12-bit ADC with up to 10 input channels, two UART/SPI/I2C capable Enhanced Capture/Compare/PWM modules, three 16-bit timers, and a real-time clock calendar with separate 32 kHz oscillator pins. The PIC24FJ64GA002 family uses a modified Harvard architecture with separate instruction and data paths, allowing instruction fetch and data access to occur in the same cycle. C compiler optimization (MPLAB XC16) is supported with a C-friendly instruction set, 16 working registers, and 32 interrupt vectors with configurable priority. CodeGuard basic security prevents unauthorized Flash reads for IP protection. Typical applications include low-power IoT sensor nodes, battery-powered portable instrumentation, USB/USB-OTG device firmware (with the PIC24F USB variant), industrial control panels, and consumer white goods. The wide 2.0V-3.6V operating range and nanoWatt XLP modes are especially useful for coin-cell or AAA-cell products that must run for years without battery replacement. Design with at least a 100 nF decoupling capacitor on every VDD pin and a 10 uF bulk capacitor on the main rail. Leave the DISVREG pin tied correctly per the package variant (see datasheet) to ensure the on-chip voltage regulator powers the core cleanly without noise coupling into analog peripherals. This page synthesizes distributor pricing, drop-in same-package and cross-package compatible alternatives, design notes, and comparison data that are not available on any single manufacturer page.

詢價 聯絡我們
PIC24FJ64GA002-E/SO - 16-bit 32MHz 64KB Flash MCU | Microchip
PIC24FJ64GA002-E/SO

PIC24FJ64GA002-E/SO - 16-bit 32MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC24FJ64GA002-E/SO is a 16-bit PIC24F microcontroller IC running at up to 32MHz with 64KB (22K x 24) of Flash program memory and 8KB of RAM, housed in a 28-pin SOIC wide-body package with industrial-grade -40C to +125C operating temperature. The device integrates a 10-bit ADC, multiple timers, UART, SPI, and I2C peripherals, and is part of Microchip's PIC24F general-purpose flash MCU family. A 16-bit microcontroller is a microprocessor core with a 16-bit data path, instruction set, and registers, offering a balance between 8-bit simplicity and 32-bit performance. In the semiconductor taxonomy, the PIC24FJ64GA002 sits within microcontrollers -> embedded processors -> integrated circuits. The 16-bit MCU family (PIC24) is the bridge tier between Microchip's 8-bit PIC16/PIC18 lines and 32-bit PIC32 parts, giving designers substantially more compute headroom and addressable memory than 8-bit parts without the complexity of a 32-bit ARM Cortex-M core. Key features include 16 MIPS performance at 32MHz CPU clock, 64KB self-programmable Flash with EEPROM emulation, 8KB SRAM, a 10-bit ADC with up to 13 analog channels, 5x16-bit timers, two UART modules, two SPI modules, and an I2C module. The -E suffix indicates the extended temperature grade (-40C to +125C), making the part suitable for industrial and harsh-environment designs. Technically, the PIC24FJ64GA002 uses a modified Harvard architecture with a 16-bit datapath, 24-bit instructions, and a hardware multiplier that performs a 16x16-bit multiplication in one cycle. The device runs from 2.0V to 3.6V and supports nanoWatt sleep modes that drop quiescent current into the microamp range, enabling battery-powered designs. Typical applications include industrial sensor nodes, low-power IoT endpoints, motor control front-ends, USB device interfaces (with on-chip USB 2.0 full-speed transceiver in select variants), home automation controllers, and educational/prototyping boards. The 28-pin SOIC wide-body footprint makes hand-soldering and rework straightforward for hobbyists and small-volume production. When designing with this part, note that the 'E' suffix denotes the extended temperature grade (different from the -I grade which runs -40C to +85C). Engineers targeting AEC-Q100 automotive qualification should select a different PIC24F variant. For programming, Microchip's MPLAB X IDE with the XC16 compiler is the canonical toolchain; ICD 3 and PICkit 4 programmers/debuggers are supported out of the box. This page synthesizes distributor pricing, parametric alternatives, and practical design considerations for the PIC24FJ64GA002-E/SO beyond the manufacturer datasheet, including a direct comparison with the closely related PIC24FJ64GA002-I/SO and PIC24FJ32GA002-E/SO drop-in equivalents.

詢價 聯絡我們
PIC24FJ64GA002-E/SP - 16-bit MCU 64KB Flash 28-SPDIP | Microchip
PIC24FJ64GA002-E/SP

PIC24FJ64GA002-E/SP - 16-bit MCU 64KB Flash 28-SPDIP | Microchip

The Microchip Technology PIC24FJ64GA002-E/SP is a 16-bit PIC24F microcontroller featuring 64 KB of Flash program memory, 8 KB of RAM, and a 32 MHz (16 MIPS) CPU core, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It belongs to the nanoWatt XLP (eXtreme Low Power) family and operates from 2.0V to 3.6V, making it well suited to battery-powered and energy-harvesting designs. A microcontroller (MCU) is an integrated circuit that combines a CPU, memory, and programmable I/O peripherals on a single die, allowing embedded systems to perform sensing, control, and communication tasks without external logic. The PIC24F sits in the hierarchy of microcontrollers -> 16-bit MCU -> RISC microcontroller -> embedded processor -> semiconductor, providing more computational headroom than 8-bit PIC18 devices while consuming less power than 32-bit PIC32 parts. Key features include 64 KB Flash (22K x 24 words), 8 KB SRAM, integrated 16-channel 10-bit ADC, four 16-bit timers, two UART, two SPI, two I2C peripherals, a Real-Time Clock/Calendar (RTCC) with calendar mode, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing. It also offers five PWM/Output Compare modules, a Parallel Master Port (PMP), and a 4-wire programming/debug interface (ICSP) that supports Microchip's MPLAB X IDE and PICkit programmers. The device uses Microchip's modified Harvard architecture with a 16-bit wide data path and 24-bit instruction word, giving it strong C-compiler efficiency through the MPLAB XC16 toolchain. Internal RC oscillators and a 32 kHz secondary oscillator reduce external component count, while the nanoWatt XLP features bring sleep currents down to roughly 20 nA in Deep Sleep mode, enabling multi-year battery life in periodic-sampling sensor nodes. Typical applications include industrial sensor hubs, handheld instrumentation, USB/HID peripherals, building automation, low-power wireless sensor nodes, motor control front-ends, and consumer white goods where the 28-SPDIP package simplifies hand-soldered prototypes and field-replaceable modules. When designing with this part, budget for decoupling (100 nF on each VDD/AVDD pair plus a bulk 10 uF), keep analog and digital grounds separated until they join at the MCU, and remember that the PIC24FJ64GA002-E/SP is the Extended (E) temperature grade -40C to +125C, so the -I variant is preferred for benign consumer-only environments. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the bare manufacturer datasheet, supporting engineers making sourcing and second-source decisions.

詢價 聯絡我們
PIC24FJ64GA002-I/ML - 16-bit MCU, 64KB Flash, 28-QFN | Microchip
PIC24FJ64GA002-I/ML

PIC24FJ64GA002-I/ML - 16-bit MCU, 64KB Flash, 28-QFN | Microchip

The Microchip Technology PIC24FJ64GA002-I/ML is a 16-bit RISC Flash microcontroller from the PIC24F family, delivering 16 MIPS performance at 32 MHz with 64 KB (22K x 24) of program Flash memory and 8 KB of SRAM in a 28-pin QFN (6x6 mm) package with exposed pad. The device operates from 2.0 V to 3.6 V across the industrial -40C to +85C temperature range and is AEC-Q100 qualified for automotive use. A microcontroller (MCU) is a single-chip computer containing a CPU core, volatile and non-volatile memory, and programmable peripherals. Microcontrollers sit within the broader semiconductor hierarchy as integrated circuits > digital logic ICs > microcontrollers, and they form the lowest-level intelligence layer beneath microprocessors in embedded systems. The PIC24F family uses a modified Harvard 16-bit architecture with a wide 24-bit instruction word that improves code density relative to 8-bit MCUs while keeping the peripheral ecosystem simple. Key features include a 16-channel 10-bit A/D converter with 500 ksps throughput, two UART/SPI/I2C configurable serial interfaces, five 16-bit timers, a real-time clock calendar, and a peripheral pin select (PPS) remappable I/O subsystem on 21 general-purpose I/O pins. The integrated charge time measurement unit (CTMU) enables touch sensing and capacitive measurement, while the JTAG interface supports in-circuit debugging and boundary-scan testing per the IEEE 1149.1 standard. Architecturally, the PIC24FJ64GA002 separates program Flash (64 KB) and data EEPROM (no separate EEPROM on this part; emulation is supported from Flash) from the 8 KB SRAM, with a unified 16 KB data Flash auxiliary region used for EEPROM emulation and parameter storage. The 16-bit modified-Harvard pipeline, hardware multiplier, and divide engine deliver deterministic 16 MIPS throughput, while the integrated 8 MHz internal oscillator plus PLL simplify BOM cost by eliminating external clocking hardware in many designs. Typical applications include automotive body controllers, HVAC control modules, industrial sensor interfaces, low-power handheld instrumentation, and USB/connectivity co-processor bridging. The combination of 64 KB Flash and 8 KB SRAM is well matched to mid-tier embedded protocols and small graphical user interfaces. The AEC-Q100 grade also makes it suitable for under-hood and cabin automotive subsystems where the -40C to +85C range is mandatory. When designing with this device, ensure the QFN exposed pad is soldered to a sufficiently large copper pour to meet the 31 C/W typical thermal resistance and to provide a low-inductance ground reference. PPS configuration must be programmed before enabling peripherals, and unused pins should be configured as outputs low to minimize current leakage on this 16 MIPS architecture. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
PIC24FJ64GA002-I/SO - 16-bit 32MHz 64KB Flash MCU | Microchip
PIC24FJ64GA002-I/SO

PIC24FJ64GA002-I/SO - 16-bit 32MHz 64KB Flash MCU | Microchip

The Microchip PIC24FJ64GA002-I/SO is a 16-bit PIC24F RISC microcontroller with 64KB of Flash program memory and 8KB of RAM, operating at up to 32MHz (16 MIPS) in a 28-pin SOIC wide package. It features a 10-bit ADC, JTAG boundary scan, and a rich peripheral set including UART, SPI, and I2C, targeting general-purpose embedded applications. The industrial temperature range of -40C to +85C and 2.0V-3.6V wide operating voltage make it suitable for battery-powered and industrial designs. What is a PIC24F microcontroller? The PIC24F family from Microchip is a 16-bit flash microcontroller family built on a modified Harvard architecture with a 16-bit wide data path and 24-bit wide instructions. Within the broader taxonomy, PIC24F sits between 8-bit PIC MCUs and 32-bit PIC32 devices, occupying the mid-range slot where engineers need more compute and memory than 8-bit offers, but the simplicity and low cost of a PIC rather than the complexity of an ARM Cortex-M part. The 'FJ' sub-family specifically adds nanoWatt XLP (eXtreme Low Power) technology for portable designs. Key differentiating specifications include 64KB Flash (22K x 24 instruction words), 8KB SRAM, 21 digital I/O pins, 16-channel 10-bit ADC, two UART modules, two SPI modules, and two I2C modules. Real-Time Clock/Calendar (RTCC) hardware and a 32kHz secondary oscillator support time-keeping applications without the main core running. Five 16-bit timers/counters and nine 16-bit PWM channels enable motor-control and lighting designs. JTAG and ICSP (In-Circuit Serial Programming) provide flexible debug and field-upgrade paths. Architecturally, the PIC24FJ64GA002 uses a modified Harvard bus with separate program and data paths, allowing simultaneous instruction fetch and data access. The CPU executes most instructions in one cycle, delivering 16 MIPS at 32MHz. The 24-bit instruction width supports large immediate operands and a uniform addressing model across the entire memory map. A peripheral pin-select (PPS) feature on related parts is not present here, but the device still offers flexible peripheral mapping within its 28-pin envelope. Typical applications include industrial sensor nodes, USB device controllers (with on-chip USB 2.0 FS), home-automation gateways, low-power remote controls, battery-powered data loggers, motor-control fan drivers, and consumer white-goods user interfaces. The 28-pin SOIC package is easy to hand-solder and breadboard-friendly for prototyping, while remaining compatible with high-volume SMT lines. When designing with this device, allocate sufficient decoupling (100nF plus 10uF bulk) close to VDD/AVDD pins. The PIC24FJ64GA002 supports a wide 2.0V-3.6V supply range, but the ADC accuracy is best at 3.3V; for 5V system interfaces, add level shifters on I/O lines. The internal 8MHz Fast RC oscillator can be trimmed using the FCR calibration register, allowing designs to operate without an external crystal in cost-sensitive applications. This page synthesizes distributor pricing, drop-in alternative parts in the same SOIC-28 footprint, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the PIC24FJ64GA002-I/SO for both new designs and as a drop-in replacement in legacy PIC24FJ designs.

詢價 聯絡我們
PIC24FJ64GA002-I/SP - 16-Bit 64KB MCU | Microchip
PIC24FJ64GA002-I/SP

PIC24FJ64GA002-I/SP - 16-Bit 64KB MCU | Microchip

The Microchip Technology PIC24FJ64GA002-I/SP is a 16-bit PIC24F general-purpose Flash microcontroller with 64 KB of Flash memory, 8 KB of RAM, operation up to 32 MHz, and up to 16 MIPS performance in a 28-pin SPDIP package. It provides 21 I/O pins, a 17 x 17 hardware multiplier, and a 32-bit x 16-bit hardware divider for efficient embedded control and signal-processing workloads. A microcontroller is a programmable control component that integrates a processor core, memory, and peripherals on one semiconductor device. The PIC24FJ64GA002 belongs to the PIC24F family, which combines a 16-bit RISC architecture with general-purpose embedded-system features. Its position within the hierarchy is microcontroller, embedded processor, programmable controller, and semiconductor. Compared with an 8-bit MCU, the 16-bit architecture provides greater arithmetic width while retaining a compact, cost-conscious control design. Key features include 64 KB of program Flash, 8 KB of data RAM, 21 I/O pins, and a 32 MHz maximum clock indication. The hardware multiplier supports efficient multiplication operations, while the hardware divider accelerates 32-bit-by-16-bit division. The MCU is intended for 2.5 V and 3.3 V operation and is available in a tube-packaged 28-pin SPDIP format for through-hole industrial and embedded assemblies. The PIC24F architecture supports a C-compiler-optimized instruction set and single-cycle execution, according to the family datasheet listing. This combination makes the device suitable for control loops, signal conditioning, protocol handling, and system management where a compact 16-bit processing engine is preferable to a larger host processor. Its 64 KB Flash capacity also provides room for application code, configuration data, and field-upgrade logic in moderately complex embedded products. Typical applications include industrial control panels, environmental monitoring, data-acquisition front ends, programmable logic controllers, building controls, and compact embedded instruments. The 21 available I/O pins allow the MCU to connect digital sensors, switches, indicators, communications interfaces, and external interface circuits without requiring a large external expansion controller. For PCB and firmware planning, confirm the exact pin assignments, peripheral multiplexing, oscillator requirements, and programming connections in the Microchip datasheet and pin-description tables. The 28-pin SPDIP format simplifies prototyping and through-hole assembly, but it requires sufficient board spacing and appropriate handling around the leads. This product page consolidates the exact PIC24FJ64GA002-I/SP identifiers, manufacturer specifications, package details, search-oriented technical guidance, and practical replacement analysis. It also distinguishes directly compatible alternatives from package or temperature-grade variants that require a different footprint or qualification review.

詢價 聯絡我們
PIC24FJ64GA002-I/SS - 16-bit 64KB Flash 32MHz MCU | Microchip
PIC24FJ64GA002-I/SS

PIC24FJ64GA002-I/SS - 16-bit 64KB Flash 32MHz MCU | Microchip

The Microchip PIC24FJ64GA002-I/SS is a 16-bit microcontroller from the PIC24F family, offering 64 KB of Flash program memory, 8 KB of RAM, and a maximum CPU speed of 32 MHz, packaged in a 28-pin SSOP (5.30 mm body width, 0.65 mm pitch). It integrates a 16-channel 10-bit ADC, multiple UART/SPI/I2C peripherals, five 16-bit timers, and the nanoWatt Technology power-management feature set for ultra-low sleep current. A 16-bit microcontroller is a programmable embedded controller that uses a 16-bit data path, instruction word, and register file to deliver noticeably higher arithmetic throughput than 8-bit MCUs while retaining deterministic real-time interrupt behaviour. PIC24F devices sit in Microchip's mid-range 16-bit portfolio above the PIC16 and PIC18 8-bit families, with the PIC24F sub-family focused on low-power general-purpose applications rather than the dsPIC33 DSP-enhanced line. They are widely used as glue logic, sensor hubs, and human-interface controllers in cost-sensitive industrial and consumer products. Key features of the PIC24FJ64GA002 include: 64 KB (22K x 24) Flash, 8 KB RAM, sixteen 10-bit ADC channels, two UART, two SPI, one I2C, five 16-bit timers, two analog comparators, a charge time measurement unit (CTMU), and a real-time clock calendar (RTCC). The nanoWatt Technology suite provides multiple idle and sleep modes with sub-microamp sleep current, making the part well suited to battery-powered sensor nodes. The 28-SSOP footprint is pin-compatible with the dsPIC33FJ64GP202 device family and shares substantial pinout overlap with the PIC18F46J11. The CPU is built around Microchip's modified Harvard architecture with a 16-bit datapath and 24-bit instructions. Code executes from internal Flash with single-cycle multiply support, and peripheral pin select (PPS) lets designers remap digital functions to a wide choice of I/O pads, simplifying PCB layout. A wide operating voltage range from 2.0 V to 3.6 V allows direct connection to single-cell Li-ion or two-AA battery chemistries. Typical applications include USB-device/embedded host controllers (with external transceiver), sensor interface boards for HVAC and industrial monitoring, low-power data loggers, simple user-interface panels, and consumer appliances where 8-bit headroom is insufficient. For battery-powered designs, the part's nanoWatt features allow months of standby life on a small cell. When designing with this MCU, ensure decoupling: place a 0.1 µF ceramic on each VDD pin within 2 mm, and verify that all VSS pins are connected - even one floating VSS may cause programming failure. Use Microchip's MPLAB X IDE with the XC16 compiler for full peripheral library support. This page synthesizes distributor pricing, drop-in SSOP-28 alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shortlist a 16-bit PIC24F platform faster.

詢價 聯絡我們
PIC24FJ64GA004-E/ML - 16-bit MCU, 64KB Flash, 44-QFN | Microchip
PIC24FJ64GA004-E/ML

PIC24FJ64GA004-E/ML - 16-bit MCU, 64KB Flash, 44-QFN | Microchip

The Microchip Technology PIC24FJ64GA004-E/ML is a 16-bit PIC® microcontroller from the PIC24F family, featuring 64 KB of Flash program memory, 8 KB of RAM, and execution at up to 16 MIPS (32 MHz CPU clock). It is offered here in the 44-pin QFN (8x8 mm) package, designated by the /ML suffix, and the -E temperature grade covering -40 °C to +125 °C for industrial and extended-environment use. A 16-bit microcontroller (MCU) is a single-chip computer whose CPU datapath is 16 bits wide, sitting between 8-bit parts (PIC10/12/16, 8051, ATmega) and 32-bit parts (Cortex-M, PIC32). The PIC24FJ family uses a modified Harvard architecture with separate program and data buses, enabling single-cycle instruction fetch plus data access. The "FJ" suffix denotes the Flash-based variant with peripheral-rich general-purpose I/O, while "GA004" identifies the 28/44-pin pinout group with the USB-less analog-rich peripheral mix. Key features include 64 KB (22K x 24) self-programmable Flash, 8 KB RAM, a 10-bit ADC with up to 13 input channels (model-dependent), up to five 16-bit timers, two UART, two SPI, two I²C, a parallel master port (PMP), and a real-time clock calendar (RTCC). An integrated 8 MHz internal RC oscillator with PLL provides 32 MHz system clock without external crystals in many designs. The 44-QFN package provides an exposed thermal pad that lowers junction-to-PCB thermal resistance, while the E-grade temperature range supports harsh-environment applications. The PIC24FJ64GA004 uses Microchip's nanoWatt XLP (eXtreme Low Power) technology with multiple idle and sleep modes, deep sleep current in the nanoamp range, and on-chip voltage regulator. Its 16-bit core, deterministic interrupt latency, and dual-bus Harvard design deliver consistent execution time which is critical for real-time control loops. The 22K × 24-bit Flash word width is wider than 8-bit MCUs, allowing more efficient storage of constants and tables. Typical applications include industrial control and HMI, low-power sensor nodes, USB-less embedded control, portable instrumentation, motor and lighting control, and consumer appliances that need more headroom than PIC16 but stay within a 16-bit architecture. The wide analog integration (ADC, comparators, CTMU) supports touch and signal-conditioning front-ends without external components. When designing with this device, ensure the MCLR reset pin is pulled high through a 10 kΩ resistor and that Vcap (core regulator bypass) is decoupled with a 10 µF ceramic to ground; missing Vcap is a common bring-up failure. For low-power operation, select the deep sleep or retention modes and gate unused peripherals via PMD registers. Pin-compatible variants with different Flash/RAM density (PIC24FJ32, PIC24FJ128) exist in the same 44-QFN footprint for memory scalability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
PIC24FJ64GA004-I/ML - 16-bit 32MHz 64KB Flash MCU 44-QFN | Microchip
PIC24FJ64GA004-I/ML

PIC24FJ64GA004-I/ML - 16-bit 32MHz 64KB Flash MCU 44-QFN | Microchip

The Microchip Technology PIC24FJ64GA004-I/ML is a 16-bit microcontroller from the PIC24F family, featuring a modified Harvard architecture that delivers up to 16 MIPS at 32 MHz CPU clock speed. The device integrates 64 KB of Flash program memory (22K x 24 words) and 8 KB of RAM, housed in a 44-pin QFN package (8 mm x 8 mm) with an exposed thermal pad. It is designed for general-purpose embedded applications requiring higher computational performance than 8-bit MCUs while avoiding the cost of a full DSP engine. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM), and programmable peripherals. The PIC24F family bridges the gap between 8-bit PIC MCUs and dsPIC DSC devices, belonging to the broader 16-bit microcontroller category within Microchip's product hierarchy: PIC24F -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. Its 16-bit data path, 24-bit instruction word, and hardware multiplier/divider enable C-compiler-friendly code generation. Key features include Peripheral Pin Select (PPS), which allows remapping of digital peripheral functions to virtually any I/O pin, dramatically simplifying PCB routing. The device integrates a 16-channel 10-bit ADC (500 ksps), five 16-bit timers, four UARTs, two SPI, two I2C, a Real-Time Clock/Calendar (RTCC), and a 5-bit analog comparator. The internal 8 MHz oscillator with 4x PLL and the on-chip FRC oscillator eliminate the need for external crystals in many designs. The part operates from 2.0 V to 3.6 V and supports industrial temperature range (-40 °C to +85 °C for the -I suffix). The architecture uses two address generation units (AGUs) for separate read/write addressing of data memory, plus a 17 x 17 hardware multiplier and a 32-bit by 16-bit hardware divider that execute in a single cycle. A C-compiler-optimized instruction set and a 16-element working register array minimize interrupt latency. The integrated nanoWatt power management includes Idle, Sleep, and Deep Sleep modes that drop current consumption below 1 µA for battery-backed designs. Typical applications include industrial control panels, sensor hubs, low-cost graphical HMI with segmented LCDs, USB-to-UART bridges, energy metering, and portable medical peripherals. The 35 available I/O pins and PPS make it suitable for designs where flexibility of pin allocation outweighs the need for a high pin count. When designing with this device, plan I/O assignments around PPS first to avoid costly rework, and verify ADC acquisition time at the lowest operating voltage. JTAG/ICSP programming requires dedicated pins that should be reserved at schematic capture to avoid contention with peripherals. For low-power applications, leverage the Deep Sleep mode and the RTCC wake-up feature to achieve years of battery life. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the same Microchip PIC24FJ family, and practical design notes not collected in a single place on the manufacturer datasheet. All pricing reflects DigiKey and Mouser market data as of 2026-10-09.

詢價 聯絡我們
PIC24FJ64GA004-I/PT - 16-bit 64KB Flash MCU, 44-TQFP | Microchip
PIC24FJ64GA004-I/PT

PIC24FJ64GA004-I/PT - 16-bit 64KB Flash MCU, 44-TQFP | Microchip

The Microchip Technology PIC24FJ64GA004-I/PT is a 16-bit Flash microcontroller from the PIC24F family, delivering up to 16 MIPS at 32 MHz CPU speed with 64 KB (22K x 24 instruction words) of on-chip Flash program memory and 8 KB of RAM. Housed in a 44-pin TQFP (10x10 mm) package, this -I (industrial) grade part operates across -40C to +85C and is intended for general-purpose embedded applications outgrowing 8-bit platforms. A 16-bit microcontroller is an integrated circuit containing a CPU, memory, and peripherals on a single die, with a 16-bit data path that enables richer arithmetic, larger linear address spaces, and faster DSP-style operations than typical 8-bit MCUs while remaining easier to program than 32-bit cores. The PIC24F family specifically targets low-power, mixed-signal embedded designs and sits within Microchip's broader portfolio hierarchy of PIC10/12/14/16 (8-bit) -> PIC24F/dsPIC33 (16-bit) -> PIC32MX (32-bit) microcontrollers. Key features include Peripheral Pin Select (PPS), which allows remapping of most digital peripherals to a wide range of physical I/O pins; a 17-bit by 16-bit hardware multiplier with a 16-bit hardware divider for fast DSP-class math; an 8 MHz internal oscillator with 4x PLL and multiple divide options; up to 35 digital I/O lines; multiple Enhanced Capture/Compare/PWM modules; a 10-bit A/D converter with up to 16 channels; two analog comparators; and a real-time clock calendar. A C-compiler-optimized instruction set and 16 working registers accelerate firmware development in MPLAB X IDE. Architecturally, the part uses a modified Harvard architecture with separate program and data buses, allowing instruction fetch and operand read to occur in the same cycle. The 17-bit by 16-bit multiplier executes in one instruction cycle, enabling real-time digital filtering, fixed-point FFT, and PID-style control loops. Integrated nanoWatt XLP power management and multiple low-power modes (Idle, Sleep, Deep Sleep) make it suitable for battery-backed designs. The PPS feature in particular distinguishes this generation from earlier PIC24F devices by eliminating the fixed peripheral-to-pin binding. Typical applications include industrial control panels, low-cost motor control, sensor signal conditioning with on-chip ADC, USB device/host peripherals (with on-chip USB on related variants), portable medical instruments, home appliances, and consumer human-machine-interface products. The wide peripheral mix also supports graphical display driving and audio tone generation. When designing with this device, verify that the chosen compiler (XC16), programmer/debugger (PICkit, ICD, or MPLAB SNAP) and the 44-pin PIM on the Explorer 16/32 board are compatible with this exact die revision. Place a 0.1 uF decoupling capacitor on every VDD/AVDD pair adjacent to the package, keep crystal traces short, and consult the family reference manual sections for PPS mapping and ADC acquisition timing.

詢價 聯絡我們
PIC24FJ64GA004T-I/PT - 64KB Flash 16-bit MCU | Microchip
PIC24FJ64GA004T-I/PT

PIC24FJ64GA004T-I/PT - 64KB Flash 16-bit MCU | Microchip

The Microchip Technology PIC24FJ64GA004T-I/PT is a 16-bit PIC24F microcontroller delivering 64 KB Flash, 8 KB RAM, and a 32 MHz MIPS core in a 44-pin TQFP (10x10 mm) package. The 'T' suffix denotes tape-and-reel packaging, and the 'I' suffix indicates the industrial -40C to +85C operating range. Key features include a 16 MIPS core at 32 MHz, hardware multiplier, single-cycle hardware multiply, and 35 digital I/O pins with peripheral pin select flexibility. A microcontroller (MCU) is a compact integrated circuit containing a CPU, RAM, non-volatile program memory, timers, communication peripherals, and I/O on a single die. The PIC24F family occupies the 16-bit tier of Microchip's PIC portfolio, sitting above the 8-bit PIC16/PIC18 families and below the 32-bit PIC32MX/dsPIC families. Within the PIC24F lineup, the PIC24FJ64GA004 belongs to the General Purpose (GA) subfamily with extensive peripheral integration, and uses the nanoWatt XLP (eXtreme Low Power) technology to reduce active and sleep current draw. Architectural highlights include dual Address Generation Units (AGUs) for simultaneous read/write data memory access, a hardware 17-bit x 17-bit multiplier that produces a 32-bit result in a single cycle, a 16-bit wide data path, and a peripheral pin select (PPS) remapping scheme that allows flexible assignment of digital peripherals to physical I/O pins. The integrated Real-Time Clock and Calendar (RTCC) module runs from a 32.768 kHz crystal with dedicated alarm and calibration logic. Internal RC oscillators reduce BOM cost for low-jitter-tolerant designs. Typical applications include industrial control panels, sensor hubs, building automation nodes, low-power data loggers, USB/HID human-interface devices, and portable consumer electronics that need more headroom than an 8-bit platform without moving to a 32-bit core. For PIC24FJ64GA004T-I/PT designers, the on-chip 10-bit ADC, multiple UART/SPI/I2C peripherals, and selectable RTCC reduce the need for external components. When designing, plan for a 2.0V to 3.6V supply, provide a 10 uF bulk + 0.1 uF decoupling cluster near VDD/AVDD/VSS/AVSS pairs, and use the PPS registers to remap peripherals after each silicon revision. This page consolidates distributor pricing, drop-in alternatives drawn from the PIC24FJ family, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
PIC24FJ64GA006-I/MR - 16-bit 64KB Flash MCU, 64-VQFN | Microchip
PIC24FJ64GA006-I/MR

PIC24FJ64GA006-I/MR - 16-bit 64KB Flash MCU, 64-VQFN | Microchip

The Microchip PIC24FJ64GA006-I/MR is a 16-bit PIC24F eXtreme Low Power flash microcontroller offering 64 KB of program memory and 8 KB of on-chip data RAM in a 64-pin VQFN (9x9 mm) package with exposed thermal pad. It integrates a 16 MIPS PIC24 CPU core (16 MHz operation), 64 KB (22K x 24) self-programmable flash, 8 KB RAM, and a rich peripheral set including multiple UART, SPI, and I2C interfaces, 16-bit timers, a 10/12-bit ADC, and parallel IO. A 16-bit microcontroller (MCU) is a microprocessor that executes instructions on 16-bit data paths, doubling throughput over legacy 8-bit cores while retaining deterministic real-time behaviour. PIC24F devices fall within the broader hierarchy of microcontrollers -> embedded controllers -> semiconductor ICs and use a modified Harvard RISC architecture optimized for low-power, high-code-density embedded designs. Key features of the PIC24FJ64GA006 include eXtreme Low Power (eXLP) technology with multiple sleep modes, an integrated LCD driver on most package variants, a Real-Time Clock Calendar (RTCC), and Cryptographic Basic CodeGuard security for IP protection. The wide 2.0V-3.6V operating range simplifies battery-powered designs, while 16 MIPS sustained throughput handles USB, sensor fusion, and human-interface workloads. This part is built on a low-leakage CMOS process, with 16-channel 10-bit ADC capability, five 16-bit timers, dual comparators, and peripheral pin select (PPS) for flexible signal routing. The 64-VQFN package exposes a thermal pad that should be soldered to a ground copper pour for best electrical and thermal performance. Typical applications include industrial HMI panels, portable medical monitors, USB peripherals, eMetering, and battery-powered IoT sensor hubs. The compact 9x9 mm QFN footprint suits space-constrained boards while leaving ample GPIO for touch, display, and connectivity expansion. When designing with this MCU, ensure the exposed pad is soldered to a sufficiently large copper pour for thermal dissipation and ground integrity. Confirm decoupling capacitor placement (100 nF + bulk) per the family datasheet, and validate any low-power mode current budgets against the application battery life requirement. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-grade reference for selecting or replacing the PIC24FJ64GA006-I/MR.

詢價 聯絡我們