積體電路

子分類

📁 ADC/DAC 3,100+ 產品 📁 放大器 IC 1,700+ 產品 📁 音訊編解碼器 18 產品 📁 音訊 IC 2 產品 📁 時脈與計時 640+ 產品 📁 Comparator ICs 1 產品 📁 DSP 1,100+ 產品 📁 資料擷取 IC 2 產品 📁 數位電位器 4 產品 📁 顯示驅動器與控制器 1 產品 📁 FPGA 與 CPLD 7,100+ 產品 📁 介面 IC 3,100+ 產品 📁 LED 驅動器 1 產品 📁 邏輯 IC 450+ 產品 📁 記憶體 IC 870+ 產品 📁 微控制器 20,000+ 產品 📁 微處理器 4 產品 📁 馬達驅動器 1 產品 📁 其他 1 產品 📁 感測器與偵測器介面 1 產品 📁 特殊用途 IC 15 產品 📁 視訊 IC 13 產品

產品（38,000+)

TPA301DR - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301DR

TPA301DR - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA301DR is a 350 mW mono Class-AB audio power amplifier designed for 3.3 V and 5 V operation, with a bridge-tied-load output and an 8-pin SOIC package. The device delivers 250 mW continuously into an 8 ohm BTL load from a 3.3 V supply at less than 1% THD+N through the voice band. Its Class-AB architecture is intended for compact internal speakers where low supply voltage, simple integration, and adequate output power matter more than maximum efficiency. The TPA301DR family is specified for common 3.3 V and 5 V rails, while its shutdown behavior supports portable equipment. The bridge-tied-load topology drives the speaker differentially, eliminating the need for an output coupling capacitor in the typical application. However, the speaker terminals cannot be connected to ground or chassis ground because each output switches around the midpoint of the supply. According to the verified Texas Instruments product page and TPA301 datasheet, the device is optimized for low-voltage systems using internal speakers. The manufacturer emphasizes that output power is the principal consideration when comparing 3.3 V and 5 V operation; supply bypassing, gain settings, and stability do not require special changes between those rails. The SOIC-8 footprint supports conventional surface-mount assembly, while thermal design remains important because Class-AB output stages dissipate more power than switching amplifiers at low output levels. System designers should verify speaker impedance, gain, supply bypassing, thermal exposure, and shutdown polarity against the datasheet before production release.

詢價 聯絡我們
TPA302D - 300mW Stereo Class-AB Amplifier | Texas Instruments
TPA302D

TPA302D - 300mW Stereo Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA302D is a 300 mW stereo, analog-input Class-AB audio power amplifier with two output channels and an 8-pin SOIC (D) package. It is designed for compact audio systems operating from 5 V and 3.3 V supplies. The manufacturer describes 250 mW continuous average output per channel into an 8-ohm load and 60 mW at less than 0.06% THD+N. A Class-AB audio amplifier is a linear power-amplifier category that combines an analog input signal with transistor output stages capable of driving speakers and other finite loads. The TPA302D belongs to the broader hierarchy of audio amplifiers, audio ICs, analog signal-conditioning ICs, and semiconductor devices. Its stereo architecture supports two audio channels while its analog inputs permit direct connection to conventional audio sources. Key features include shutdown control, internal mid-rail generation, thermal protection, and short-circuit protection. The device is also identified as a functional equivalent of the LM4880 in the supplied technical data. Its 8-pin SOIC package reduces board space and supports automated surface-mount assembly. The verified product information specifically identifies the amplifier as a 300 mW stereo Class-AB device with analog input. The TPA302 architecture uses separate left and right amplification paths to provide stereo output from analog input signals. The internal mid-rail feature can support single-supply audio architectures, while shutdown control allows the system to place the amplifier in a lower-power state when audio is not required. The datasheet and product listing also indicate compatibility with 5 V and 3.3 V operation, which makes the device relevant to portable equipment, small consumer audio products, and low-voltage embedded systems. Typical applications include compact stereo speakers, portable audio equipment, auxiliary audio products, USB or docking-system audio paths, and small embedded audio subsystems. The 8-ohm speaker-load target and 250 mW continuous average capability are suitable for low-to-moderate listening levels, although the available output power depends on supply voltage, load impedance, channel balance, thermal conditions, and signal level. Designers should verify the SOIC footprint, supply decoupling, output-filter requirements, speaker wiring, thermal rise, and shutdown polarity against the manufacturer datasheet before layout release. The device is not a Class-D switching amplifier, so its output-stage dissipation and analog signal integrity should be checked carefully in continuous-use designs.

詢價 聯絡我們
TPA302DR - 300mW Stereo Class-AB Amplifier | Texas Instruments
TPA302DR

TPA302DR - 300mW Stereo Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA302DR is a 300 mW stereo analog-input Class-AB audio amplifier with a 1.5 MHz bandwidth, 5.5 V maximum supply voltage, and an 8-pin SOIC package. It delivers 250 mW per channel into an 8-ohm load and provides 60 mW of continuous output power at less than 0.06% THD+N. Designed for compact audio systems, the TPA302DR combines stereo output, internal mid-rail generation, shutdown control, and thermal and short-circuit protection in a low-profile surface-mount package. A Class-AB audio amplifier is an analog signal-processing integrated circuit that uses push-pull transistor output stages to drive speakers or other low-impedance loads. The TPA302DR belongs to the broader audio-amplifier hierarchy, which includes stereo amplifiers, linear amplifiers, and semiconductor power amplifiers. Its Class-AB architecture provides continuous bipolar output rather than the pulsed output associated with Class-D designs, making it suitable for low-power portable, personal-audio, and auxiliary audio products. Key features include 300 mW stereo output capability, 1.5 MHz bandwidth, operation from 5 V and 3.3 V rails, internally generated mid-rail voltage, shutdown control, and thermal and short-circuit protection. The 8-pin SOIC package reduces board area and supports automated surface-mount assembly. These characteristics make the device useful where two analog audio channels must drive headphones or small speakers without the complexity of a switching amplifier and external mid-rail circuitry. The amplifier accepts analog left- and right-channel inputs and uses external gain-setting resistors to establish channel gain. According to the Texas Instruments TPA302 data sheet, the device is specified for operation from a 5 V supply and is also compatible with 3.3 V operation. Its internally generated mid-rail provides a convenient common return for single-supply audio signals, while the shutdown function can reduce supply consumption when the audio path is not active. Typical applications include portable speakers, headphone and headset drivers, personal-audio accessories, small consumer-audio systems, and compact embedded audio products. The 250 mW-per-channel capability into 8 ohms is appropriate for low-impedance transducers rather than high-power loudspeaker systems. System designers should confirm speaker impedance, amplifier gain, input coupling, output configuration, and power-supply headroom before finalizing the analog and layout design. A key design consideration is the distinction between the 300 mW headline output rating and the verified application condition of 250 mW per channel into 8 ohms. Allow for copper, nearby heat sources, enclosure temperature, and supply tolerance, and use the datasheet thermal information to assess reliable operation. This page synthesizes verified manufacturer and distributor information, engineering design notes, comparison data, and drop-in replacement guidance beyond the basic distributor listing.

詢價 聯絡我們
TPA311D - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA311D

TPA311D - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA311D is a 350 mW mono Class-AB audio amplifier with bridge-tied-load to single-ended switching mode, specified for 3.3 V and 5 V operation and housed in an 8-pin SOIC package. It is designed for low-voltage audio paths where an internal speaker and external earphone may share the same system. According to the verified distributor listing, TPA311D is a one-channel mono Class-AB amplifier in an 8-SOIC package. A Class-AB audio amplifier is a linear audio amplifier whose output devices conduct for part of the signal cycle. In the audio-power hierarchy, it provides a relatively linear output with less switching-related EMI than many Class-D solutions, making it useful in compact voice, portable-device, and low-voltage speaker systems. The TPA311 family also supports bridge-tied-load and single-ended operating modes, allowing the device to serve internal-speaker and earphone paths with appropriate output configuration. The verified data identifies the TPA311 as a 350 mW mono audio power amplifier and highlights operation at 3.3 V and 5 V, wide power-supply compatibility, bridge-tied-load to single-ended mode control, integrated depop circuitry, and thermal and short-circuit protection. The manufacturer product page describes 250 mW continuous power into a bridge-tied 8-ohm load at less than 1% THD+N throughout voice-band frequencies when operated from a 3.3 V supply. These figures describe the TPA311 family context associated with TPA311D. The architecture is suitable for compact audio equipment where a low-voltage supply limits available output power. The integrated protection features help manage thermal and short-circuit conditions, while depop circuitry helps control output transients during startup or mode changes. Engineers should still validate speaker impedance, supply headroom, thermal dissipation, and the selected output topology against the manufacturer datasheet before releasing a production PCB. Typical uses include portable audio products, voice-enabled devices, small speaker systems, headphone or earphone interfaces, and embedded audio subsystems. The 8-SOIC package simplifies assembly for designs using conventional surface-mount production processes. Because the target is a legacy audio amplifier family, availability, lifecycle status, pricing, and exact electrical limits should be reconfirmed from current manufacturer and distributor data. A key design consideration is the difference between the family headline rating of 350 mW and the verified 3.3 V application condition of 250 mW into an 8-ohm BTL load at less than 1% THD+N. The circuit must be designed around the actual supply, load, package thermal behavior, and output mode rather than treating the headline power as an unconditional speaker rating. This page combines verified source data with structured engineering guidance and clearly identifies unavailable parameters.

詢價 聯絡我們
TPA311DG4 - 350mW Mono Class AB Amplifier | Texas Instruments
TPA311DG4

TPA311DG4 - 350mW Mono Class AB Amplifier | Texas Instruments

The Texas Instruments TPA311DG4 is a 350 mW mono audio power amplifier IC for low-voltage audio systems, operating from 3.3 V or 5 V and housed in an 8-pin SOIC surface-mount package. It is a Class AB amplifier that supports bridge-tied load (BTL) and single-ended (SE) operating modes, includes integrated depop circuitry, and provides thermal and short-circuit protection. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a speaker or another defined load. In the broader hierarchy, the TPA311DG4 is a mono Class AB audio amplifier, an amplifier IC, an integrated circuit, and a discrete signal-processing component for low-voltage audio equipment. Its BTL architecture allows an internal speaker to be driven without a speaker-blocking capacitor, while SE mode supports external earphone operation. The device is specified for 3.3 V and 5 V operation, with a maximum supply voltage of 5.5 V. Its 350 mW output-power description makes it suitable for compact internal speakers and low-power audio paths. A distributor listing also reports 0.7 W nominal output power, but the manufacturer-linked search description identifies the TPA311DG4 specifically as a 350 mW mono audio power amplifier. System designers should therefore confirm the exact test conditions and load used in the manufacturer datasheet before sizing the speaker and supply. The TPA311 family combines a fully specified low-voltage operating range with BTL-to-SE mode control, integrated depop circuitry, and built-in thermal and short-circuit protection. These features make the amplifier appropriate for products using either 3.3 V or 5 V system rails. The 8-pin SOIC package also supports automated assembly and compact board layouts, although adequate copper and thermal layout remain necessary when continuous audio output causes appreciable internal dissipation. Typical applications include portable speaker systems, compact consumer audio products, and low-voltage equipment requiring an internal mono speaker plus an external headphone path. The part can also serve as the power stage in a larger audio subsystem when the design only requires a small speaker output. Its protection functions reduce system risk during abnormal load conditions, but they do not replace correct speaker impedance selection, supply decoupling, or thermal design. A key design consideration is the difference between BTL and SE mode. In BTL mode, the amplifier drives the speaker differentially and does not require an output coupling capacitor. In SE mode, one output is referenced differently to support an earphone load. Designers should follow the manufacturer configuration, component values, and decoupling guidance rather than assuming that the two modes have identical load, output-power, or stability requirements. This product page consolidates the verified manufacturer and distributor descriptions for the TPA311DG4, identifies the available pin-compatible family comparisons, and adds application guidance that is not presented as a substitute for the official electrical characteristics, absolute maximum ratings, and test-condition tables in the manufacturer datasheet.

詢價 聯絡我們
TPA311DGN - 350mW Mono Class-AB Audio Amplifier | Texas Instruments
TPA311DGN

TPA311DGN - 350mW Mono Class-AB Audio Amplifier | Texas Instruments

The Texas Instruments TPA311DGN is a 350 mW, mono, Class-AB audio amplifier with bridge-tied load (BTL) or single-ended output capability, designed for low-voltage portable audio systems. The device operates from a 3.3 V supply and is specified to deliver up to 250 mW continuous power into an 8 ohm BTL load at less than 1% THD+N, according to the manufacturer product information. It is packaged in an 8-pin HVSSOP DGN surface-mount package with a PowerPAD thermal pad. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a speaker or other low-impedance transducer. A BTL arrangement uses both output terminals to drive the speaker differentially, which increases voltage swing and can reduce the need for an output coupling capacitor. A Class-AB output stage provides continuous conduction with lower crossover distortion than a typical Class-D architecture, making the TPA311 useful for small speakers, internal speakers, and portable audio products. Key features include mono operation, a 350 mW output-power rating, Class-AB operation, BTL and single-ended modes, shutdown support with speaker-noise reduction, and an 8-pin HVSSOP package. The product information identifies the amplifier as a 3.3 V, 8 ohm audio solution with approximately 1.4 MHz switching or operating frequency information shown by a distributor listing; the exact interpretation of that frequency should be confirmed against the manufacturer datasheet for the specific design configuration. The TPA311 is appropriate for portable media players, compact speakers, personal audio products, and low-voltage embedded systems where a mono speaker is sufficient. In a typical implementation, the audio source drives the amplifier input through the device's gain-setting network, while the BTL output connects directly across the speaker. The single-ended output option can support headphone-style or externally terminated loads, subject to the datasheet's output and load restrictions. Designers should pay close attention to supply decoupling, speaker impedance, thermal performance of the exposed pad, and the distinction between BTL and single-ended wiring. The HVSSOP package improves board-space efficiency compared with the larger 8-pin SOIC option, while the PowerPAD provides a thermal connection to the PCB copper area. Application details, limit values, gain options, and recommended external components must be taken from the manufacturer datasheet rather than inferred from distributor summaries.

詢價 聯絡我們
TPA311DR - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA311DR

TPA311DR - 350mW Mono Class-AB Amplifier | Texas Instruments

Texas Instruments TPA311DR is a 350 mW mono Class-AB audio power amplifier with bridge-tied-load and single-ended operating modes, specified for operation from a 3.3 V supply and supplied in an 8-pin SOIC package. It is designed to drive internal speakers or external earphones in compact, low-voltage audio systems. According to the manufacturer product page, the TPA311 family supports fully specified 3.3 V and 5 V operation, integrated BTL-to-SE mode control, integrated depop circuitry, and thermal and short-circuit protection. The R suffix identifies the taped-and-reeled ordering option, while the device itself is a single-channel Class-AB audio amplifier. An audio power amplifier is an integrated circuit that converts a low-level audio input into a higher-current signal capable of driving a loudspeaker or other transducer. The TPA311 belongs to the Class-AB amplifier hierarchy within audio amplifiers and power-management ICs. Its bridge-tied-load mode increases usable output voltage into a differential speaker, while single-ended mode allows the same device to drive an external earphone when the system requires a grounded output. Key features include 350 mW rated output capability, compatibility with 3.3 V and 5 V supplies, integrated BTL-to-SE mode control, integrated depop circuitry, and built-in thermal and short-circuit protection. These features make the device suitable for portable audio, voice terminals, personal-audio products, and other compact systems in which a single-speaker or earphone output is needed without a large external amplifier module. The architecture is optimized for low-voltage operation. At a 3.3 V supply, the manufacturer documentation describes 250 mW continuous output into an 8-ohm BTL load at less than 1% THD+N across voice-band frequencies. The lower output-power figure reflects the device's 3.3 V operating condition; the family-level headline rating is 350 mW. BTL operation suppresses the DC output offset at the speaker and can provide greater output swing than a conventional single-ended amplifier. Typical applications include portable media players, personal audio accessories, voice-call terminals, compact speakers, and low-voltage embedded audio products. The TPA311DR can be selected when the board uses an 8-pin SOIC footprint and requires integrated protection rather than a discrete output stage. A key design consideration is output-mode configuration: the mode-control function must be connected or configured as required by the manufacturer reference design for the intended BTL or SE load. Input and output decoupling, speaker-return routing, thermal copper, and clean grounding are essential for low distortion and stable operation. This page consolidates verified manufacturer and distributor information, drop-in candidate screening, application guidance, and practical PCB considerations. It also distinguishes explicitly sourced facts from unavailable specifications, helping engineers make a defensible design decision without relying on a generic distributor listing alone.

詢價 聯絡我們
TPA3125D2N - 10W Stereo Class-D Amplifier | Texas Instruments
TPA3125D2N

TPA3125D2N - 10W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TPA3125D2N is a Class-D audio power amplifier rated for 10 W per channel in stereo single-ended operation and 20 W in mono bridge-tied-load operation. It accepts a 10 V to 26 V supply, supports analog input signals, and is offered in the TPA3125D2N configuration as a 20-pin PDIP package rated for -40°C to 85°C operation. A Class-D audio amplifier is a power-management semiconductor that converts analog input signals into high-frequency switching waveforms and reconstructs the amplified audio at the speaker output. The Class-D architecture belongs to the amplifier IC hierarchy and achieves high power-conversion efficiency compared with conventional linear audio amplifiers. This efficiency helps the TPA3125D2N eliminate the need for an external heat sink during normal music playback, although PCB layout and thermal design still require attention. The TPA3125D2 supports two principal operating arrangements. In stereo mode, its single-ended outputs can drive two speakers as low as 4 Ω, with up to 10 W delivered to each channel. In bridge-tied-load mode, the two output channels combine to drive one speaker at up to 20 W. Gain is controlled externally, allowing the signal-chain gain to be matched to the source level without relying on a fixed internal gain setting. The device is intended for analog-input audio systems where a compact, efficient power stage is required. Its supply range accommodates common amplified-speaker, multimedia, television, consumer-audio, and compact embedded systems. The 20-pin PDIP package favors through-hole assembly and repairability, while the operating-temperature range supports industrial-temperature applications requiring a broad ambient range. Class-D output stages demand careful PCB layout because high-frequency switching currents can create electromagnetic interference, ground bounce, and instability if output and input paths are not separated. Place the input and feedback components away from the switching outputs, keep speaker-current loops compact, and provide a low-impedance ground return. The decoupling network should follow the manufacturer’s recommended application circuit to control supply transients. The principal design trade-off is package size versus assembly convenience. The PDIP-20 body is larger than a surface-mount power package, but it is straightforward to assemble, inspect, and service. It is a practical choice for moderate-power audio products where efficient operation, analog gain control, stereo-to-mono flexibility, and straightforward through-hole construction outweigh the need for minimal PCB area. This product overview combines the manufacturer’s device description with a practical comparison of stereo and bridge-tied-load operation, output loading, package implications, thermal expectations, and layout considerations. It also identifies which candidate replacements have documented equivalence and where additional design verification is still required.

詢價 聯絡我們
TPA321D - 700mW Mono Class-AB Audio Amp | TI
TPA321D

TPA321D - 700mW Mono Class-AB Audio Amp | TI

The Texas Instruments TPA321D is a 700 mW mono analog-input Class-AB audio power amplifier with differential inputs, operating from 2.5 V to 5.5 V in an 8-pin SOIC package. It is designed for low-voltage systems that drive internal speakers through a bridge-tied-load output. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an analog audio signal so it can drive a loudspeaker or other finite impedance. A Class-AB amplifier provides linear operation with lower crossover distortion than a traditional Class-B design. A differential input accepts signal voltage between two input terminals, while a bridge-tied-load output uses both amplifier outputs to develop voltage across the speaker without requiring a speaker-coupling capacitor. The TPA321 family is specified for 3.3 V and 5 V operation and supports a 2.5 V to 5.5 V supply range. At a 3.3 V supply, the manufacturer material states that the device can deliver 250 mW continuously into an 8-ohm bridge-tied load with less than 1% THD+N over the voice band. The TPA321D ordering option is supplied in the 8-pin SOIC package and supports a -40°C to +85°C operating-temperature range. Differential input architecture can help reject common-mode noise when the source is balanced or when noise appears equally on both input conductors. The bridge-tied-load topology places the speaker between OUT+ and OUT-, so neither output pin should be grounded merely to establish a common reference. Input, supply, and output stability components must be implemented according to the manufacturer datasheet to preserve stable operation and acceptable distortion. Typical uses include portable-device speakers, compact audio accessories, personal-audio products, and other low-voltage mono sound systems. The design is appropriate when a small internal speaker must be driven directly and board area is limited. At higher power or with a longer speaker connection, cable losses and load tolerance should be checked before release. Decoupling capacitors should be placed close to the supply pins, and input components should be arranged to minimize the audio trace area. Thermal performance depends on supply voltage, output power, speaker impedance, PCB copper, and ambient temperature. This page combines verified product information with purchasing guidance and design context. This data page distinguishes TPA321D from the broader TPA321 family, summarizes the electrically relevant evidence, and organizes sourcing and replacement questions. Values not explicitly supplied by the retrieved manufacturer or distributor data remain marked for verification rather than inferred.

詢價 聯絡我們
TPA321DG4 - 350mW Mono Class-D Audio Amp | Texas Instruments
TPA321DG4

TPA321DG4 - 350mW Mono Class-D Audio Amp | Texas Instruments

The Texas Instruments TPA321DG4 is a 350-mW mono Class-D audio power amplifier with differential inputs, specified for both 3.3 V and 5 V operation, and supplied in an 8-pin SOIC (DG4) package. It delivers its rated output into a minimum 8-ohm speaker load, draws only 0.15 microamps in shutdown mode, and limits idle supply current to 1.5 mA maximum, making it well suited to portable and low-voltage audio equipment. A Class-D audio power amplifier is a switching type of linear audio output stage in which the transistor output devices are driven fully on or fully off, so that the amplifier dissipates far less power than an equivalent Class-AB stage at the same output level. Within the broader hierarchy of audio signal-chain ICs, the TPA321DG4 sits in the power-amplifier tier, downstream of the audio DAC or codec and upstream of the loudspeaker, converting a low-level differential analog signal into a rail-to-rail differential speaker drive. Key features include full specification across a 3.3 V and 5 V supply range, differential inputs that reject common-mode noise picked up from long source traces, 0.5 percent harmonic distortion, a maximum power dissipation of 725 mW, and a maximum load resistance of 8 ohms. Shutdown current of 0.15 microamps preserves battery life in portable equipment, while the industrial temperature grade supports extended ambient operation. Internally the device uses a charge-pump-assisted Class-D output stage with differential outputs, so each output pin swings around half the supply rail. Because the outputs are differential, a bridge-tied load sees the full rail-to-rail swing and delivers roughly four times the power of a single-ended arrangement at the same supply voltage. The gain-setting and input network are entirely passive, keeping the external bill of materials small. Typical applications include compact Bluetooth and portable speakers, headset and headphone drive, USB and Type-C powered audio accessories, small Bluetooth speaker modules, alarm and industrial buzzer drivers, and low-voltage voice-assistant or smart-home nodes where a 3.3 V rail is the only supply available. Design note: because the device has differential inputs and differential outputs, do not ground the input pins or tie the two output pins together. Place the input coupling capacitors and the input resistors close to the pins, route the differential pair as a tight pair to limit common-mode pickup, and terminate each output through its own LC filter network into the speaker. This page synthesizes distributor availability, pin-compatible drop-in alternatives, a parameter-by-parameter comparison, and practical layout and thermal notes that are not consolidated in the manufacturer datasheet itself.

詢價 聯絡我們
TPA321DGN - 700mW Mono Audio Amplifier | Texas Instruments
TPA321DGN

TPA321DGN - 700mW Mono Audio Amplifier | Texas Instruments

The Texas Instruments TPA321DGN is a 700 mW mono, analog-input Class-AB audio power amplifier with differential inputs, supplied in an 8-pin HVSSOP package. It is designed for low-voltage audio systems operating from a 5 V-class supply, with operation also specified for 3.3 V systems. The device combines a mono output stage with differential signal handling, allowing a balanced or bridged signal-chain arrangement while supporting compact speaker-driving designs. An audio power amplifier is an integrated circuit that takes a low-level analog audio signal and supplies the voltage and current needed to drive a loudspeaker. The TPA321 belongs to the Class-AB linear-amplifier family, a topology commonly used for small speakers because it provides continuous analog amplification without requiring an external Class-D switching modulator. Within the broader hierarchy, it is an audio amplifier IC, analog amplifier, and power-management semiconductor intended for portable and embedded audio equipment. The principal product characteristics are its 700 mW maximum output-power capability, mono Class-AB output architecture, and differential analog inputs. According to the Texas Instruments TPA321 product page, the amplifier is specified for 3.3 V and 5 V operation, providing compatibility with common portable-device supply rails. Its differential input arrangement can improve rejection of unwanted common-mode signals when the source and return paths are balanced, although the complete signal-chain topology must still be evaluated for noise, offset, gain, and channel count. The TPA321 uses an analog Class-AB output stage rather than a switching amplifier. This architecture avoids the modulator, switching node, and associated electromagnetic-interference considerations required by Class-D solutions. The trade-off is conventional linear-amplifier behavior: supply-current demand increases with output power, and efficiency is lower than that of a comparable Class-D converter when the signal is large. The provided manufacturer and distributor information does not expose detailed internal architecture, thermal resistance, or full frequency-response limits, so those values require confirmation in the manufacturer datasheet. Typical uses include compact mono speakers in portable audio products, small consumer appliances, auxiliary audio modules, and embedded systems accepting analog input. The TPA321DGN is particularly relevant when one amplified channel is sufficient and an 8-pin surface-mount footprint is preferred over a larger power-amplifier package. Its 700 mW rating supports appropriately selected low-impedance loudspeakers, while the 3.3 V and 5 V operating focus aligns it with modern portable and embedded systems rather than high-voltage automotive audio. Designers should verify the speaker impedance, minimum load, supply range, output-power derating, and thermal performance under worst-case audio duty cycle before production use. Input and output grounding should be planned to minimize channel offset, popping, and feedback. Because the package is a compact HVSSOP, copper area and thermal-path design are important when the amplifier operates continuously near its stated output-power capability. This product record combines the verified Texas Instruments product description, distributor package and ordering information, and an engineering-oriented comparison with a documented pin-compatible-class candidate. It also distinguishes verified ratings from parameters that still require direct datasheet confirmation, helping engineers evaluate procurement, PCB reuse, and audio-system suitability without relying solely on a distributor listing.

詢價 聯絡我們
TPA3244DDW - 60W Stereo Class-D Amplifier | Texas Instruments
TPA3244DDW

TPA3244DDW - 60W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TPA3244DDW is a high-performance, 60 W stereo Class-D audio power amplifier with 120 W mono capability, analog input, and pad-down construction in a 44-pin HTSSOP (DDW) package. It accepts a 12 V to 31.5 V supply, operates across a 0°C to 70°C temperature range, and uses Texas Instruments PurePath Ultra-HD technology to deliver premium sound quality with the efficiency of a Class-D output stage. A Class-D audio amplifier is a power-management IC that switches its output stage between active and inactive states, reducing the amount of energy dissipated compared with a conventional linear output stage. Within the audio-amplifier hierarchy, the TPA3244DDW combines an analog input interface, integrated power stages, speaker outputs, and thermal management in one package. This integration supports compact stereo and high-power mono designs without requiring discrete output transistors on the board. The principal feature is its 60 W stereo output rating, with the same device specified for operation as a 120 W mono amplifier. Analog input simplifies compatibility with conventional audio sources, while the 12 V to 31.5 V supply range accommodates common single-rail amplifier architectures. The pad-down HTSSOP package places the exposed thermal pad beneath the device so PCB copper can remove heat from the power stage. Its stated operating range is 0°C to 70°C, making it appropriate for indoor consumer and professional audio equipment where that environmental range is acceptable. PurePath Ultra-HD technology distinguishes this amplifier from basic Class-D solutions by targeting low output distortion and high-quality audio reproduction. The integrated switching output stage avoids the continuous bipolar dissipation associated with linear amplifier output stages, although efficiency still depends on supply voltage, output power, load impedance, and thermal design. A low-impedance, low-noise supply is important because supply noise and instability can affect the power stage even when the audio input is clean. Typical uses include powered speakers, active bookshelf speakers, compact home-theater systems, soundbars, subwoofer power stages, and multimedia speaker enclosures. In stereo operation, the amplifier can drive two speaker channels from an analog source. In a bridged mono arrangement, its 120 W capability can serve a subwoofer or high-output monoblock. The 44-pin HTSSOP package requires careful PCB layout, adequate exposed-pad thermal copper, and a clean power-supply connection. Designers should follow the recommended application diagrams in the manufacturer datasheet, preserve the exposed-pad thermal path, and use the specified input and supply decoupling. Speaker wiring and power-supply connections must be sized for the intended output level. Stereo, bridged mono, and single-ended configurations have different terminal and load constraints, so confirm the selected topology before finalizing the board layout. This page combines the official device specifications with application guidance, packaging details, and a conservative drop-in assessment. It also distinguishes verified device facts from parameters that require confirmation from the manufacturer datasheet, helping engineers plan sourcing and hardware qualification without relying on assumptions.

詢價 聯絡我們
TPA3255DDVR - 315W Stereo Class-D Amplifier | Texas Instruments
TPA3255DDVR

TPA3255DDVR - 315W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TPA3255DDVR is a 315 W stereo, 600 W mono, analog-input Class-D audio power amplifier with an 18 V to 53.5 V supply range, supplied in a 44-pin HTSSOP DDV package. It is designed for high-power audio systems requiring efficient amplification and premium sound quality. The device supports two-channel stereo operation and can also be configured for mono use at higher output power. A Class-D audio amplifier is a switching power amplifier that uses transistor switching to deliver audio energy efficiently. In the broader hierarchy, a Class-D amplifier belongs to audio amplifiers, linear and nonlinear power amplifiers, and power-management semiconductor systems. Compared with a conventional linear audio amplifier, its switching architecture can reduce wasted power and heat while maintaining high output capability. The verified product information identifies 315 W stereo output, 600 W mono output, analog input, an 18 V to 53.5 V supply range, and a 44-pin HTSSOP package. The distributor listing also identifies the amplifier as a two-channel stereo Class-D device. These ratings make it suitable for professional audio, home-theater, public-address, multimedia, and other high-power sound systems where load capability and efficiency are important. Thermal design is central to using this amplifier because Class-D power stages can dissipate substantial heat at high output power. The DDV package provides a large thermal pad for board-level heat spreading, but the exact thermal resistance, output configuration details, protection thresholds, and application-specific limits must be taken from the manufacturer datasheet. The verified distributor information reports a 44-pin PowerTSSOP package and an operating-temperature range of 0 to 70 °C for the listed orderable part. Typical implementation uses analog audio inputs into the Class-D power stage, with speaker outputs driving stereo or bridged mono configurations. The amplifier is appropriate when the system supply is in the verified 18 V to 53.5 V range and the load is compatible with the manufacturer-defined output power conditions. Board layout, speaker wiring, grounding, thermal management, and protection circuitry should follow the TI datasheet and evaluation-board guidance. This product page combines verified Texas Instruments specifications, distributor package and sourcing information, application guidance, and verified cross-reference results. It distinguishes the high-power TPA3255DDVR from lower-power or functionally similar parts that may use different packages or pin configurations.

詢價 聯絡我們
TPLD2001 - 18-GPIO PLD with I2C/SPI | Texas Instruments
TPLD2001

TPLD2001 - 18-GPIO PLD with I2C/SPI | Texas Instruments

The TPLD2001 is a programmable logic device (PLD) from Texas Instruments featuring 18 GPIOs and a selectable I2C/SPI interface. It is supplied in a 20-VSSOP package and integrates configurable macro-cells built from 2-, 3-, and 4-bit lookup tables (LUTs) together with sequential logic and analog blocks. The device operates from 1.71V to 5.5V over -40°C to 125°C and is qualified for automotive applications. A programmable logic device is an integrated circuit whose logic function is defined by the user after manufacturing. In the TPLD family, InterConnect Studio is used to configure the non-volatile memory, either by emulating OTP memory or permanently programming the one-time programmable fuse. PLDs sit between standard fixed-function logic and large CPLDs/FPGAs, providing a compact, low-power way to integrate glue logic, timing, reset, power sequencing, and I/O expansion functions. Key features include 18 GPIOs, 14 macrocells, and a configurable I2C/SPI port for system communication and in-system configuration. The 2/3/4-bit LUT macrocells allow flexible combinatorial logic; sequential blocks support timers, delays, and state machines. The wide 1.71V to 5.5V supply range permits operation from Li-ion batteries, 3.3V rails, or 5V industrial buses, and the -40°C to 125°C temperature range covers automotive and industrial environments. The device's analog blocks provide voltage monitoring and reset generation, eliminating external supervisor ICs. Its low power and compact 20-VSSOP package make it suitable for space-constrained designs. Because logic functions are configured in the OTP memory and the same base part can be used across many designs, inventory can be consolidated. The selectable I2C/SPI port also allows integration into microcontroller-based systems for status readback or dynamic reconfiguration when the non-volatile logic is emulated. Typical applications include timing delay generation, voltage monitoring and reset generation, power sequencing, I/O expansion, and glue logic consolidation in automotive body electronics, industrial sensors, and consumer devices. Designers can use InterConnect Studio to implement and simulate logic before programming. When designing with TPLD2001, plan the OTP programming step during production and verify I/O assignments before programming, because OTP cannot be changed after the permanent fuse is blown.

詢價 聯絡我們
TPS2371D - IEEE 802.3af PoE Power Interface Switch | TI
TPS2371D

TPS2371D - IEEE 802.3af PoE Power Interface Switch | TI

The Texas Instruments TPS2371D is an IEEE 802.3af-compatible power interface switch for Power over Ethernet powered devices, with an 8-pin SOIC package. It is designed for PoE powered-device front ends that require controlled power delivery from an Ethernet connection. The verified listing identifies the device as a specialized power interface switch with a nominal 48 V supply context, CMOS technology, eight terminals, and a 1.27 mm terminal pitch. A power interface switch is the input-side protection and power-management circuit between an Ethernet cable and a PoE powered device. Its role is to establish the power path, protect the downstream system from unsuitable input conditions, and support the current and voltage limits associated with legacy IEEE 802.3af PoE systems. In system terms, it belongs to the power-management IC hierarchy and the broader PoE interface ecosystem. The main verified characteristics are legacy IEEE 802.3af compatibility, operation in the PoE power domain, an 8-terminal surface-mount SOIC format, and a listed maximum operating temperature of 70 °C. The distributor record also identifies a 57 V-related comparison context, while the supplied Partstack result lists 48 V nominal voltage. These figures should be checked against the manufacturer datasheet before final design release because the search snippets do not provide the complete electrical characteristic table. Typical uses include PoE-powered IP cameras, network access points, VoIP phones, industrial Ethernet endpoints, and other powered devices connected through an Ethernet infrastructure. The device is appropriate when the design uses the legacy 802.3af power interface concept and the existing board uses the TPS2371D pin arrangement. It is not a generic USB power switch or a complete PoE PD controller; neighboring devices with similar package names may serve different voltage, current, or protection functions. For PCB implementation, place the switch close to the Ethernet input and power-entry components, maintain the datasheet-defined spacing for high-voltage copper, and provide the required input and output decoupling. Confirm absolute maximum ratings, operating voltage, current limit behavior, thermal conditions, and exposed-lead connections from the official TPS2371 documentation before applying it to a new design. This page consolidates verified distributor availability, manufacturer positioning, package information, procurement data, and design cautions for engineers evaluating TPS2371D replacements or PoE front-end implementations.

詢價 聯絡我們
TPS2371DR - IEEE 802.3af PoE PD Interface | Texas Instruments
TPS2371DR

TPS2371DR - IEEE 802.3af PoE PD Interface | Texas Instruments

The Texas Instruments TPS2371DR is an IEEE 802.3af-compatible power interface switch for Power over Ethernet powered devices, with integrated hot-swap and power-distribution functions in an 8-pin SOIC package. It provides a PD detection signature, class 0-4 classification signature, precision undervoltage lockout, a 20-ms UVLO off-time delay, and programmable inrush-current limiting. A Power over Ethernet powered-device interface is the circuit that receives power through an Ethernet cable, identifies the attached load, negotiates its power class, and safely connects that power to the local system. In the power hierarchy, a PD interface sits between the PoE supply and the powered equipment’s DC/DC converter or load. It prevents an unsupported or improperly connected network port from receiving unsafe power. The TPS2371DR’s principal engineering benefits are its IEEE 802.3af compatibility, integrated protection, and autonomous interface operation. The device provides both detection and classification signatures, eliminating separate handshake circuitry in many conventional PoE PD designs. Its internal hot-swap MOSFET helps control connection transients, while the programmable inrush limit reduces the stress applied to downstream capacitance and power circuitry. The chip also uses precision UVLO thresholds to distinguish valid operating conditions and includes a defined 20-ms off-time delay after UVLO. That delay provides controlled recovery before the interface attempts another valid operating state. As an 8-SOIC surface-mount device, the TPS2371DR supports compact PoE endpoint designs without requiring a large connector-side or board-edge package. Typical uses include IP cameras, VoIP phones, wireless access points, network switches, powered network adapters, and other low- to moderate-power Ethernet endpoints. These products can use the TPS2371DR when IEEE 802.3af behavior and a conventional eight-pin PoE PD interface are required. For higher-power or newer PoE standards, designers should verify the exact PSE, PD, class, voltage, and protection requirements before selecting this legacy-compatible device. Layout should keep the Ethernet input and power-path nodes physically separated from sensitive downstream electronics, and it should provide appropriate copper area for thermal dissipation during sustained power transfer. Component values must follow the manufacturer’s reference design because the programmable inrush and protection network determine startup behavior. The interface also requires correct grounding and protection placement to avoid allowing transient current into sensitive ports. This page consolidates the verified manufacturer, distributor, pricing, lifecycle, and replacement information for TPS2371DR, while clearly separating confirmed specifications from unavailable electrical details. It also provides application guidance and drop-in alternatives where the available cross-reference evidence supports pin and package compatibility.

詢價 聯絡我們
TPS25810ATWRVCRQ1 - Automotive 3A USB-C DFP Controller | TI
TPS25810ATWRVCRQ1

TPS25810ATWRVCRQ1 - Automotive 3A USB-C DFP Controller | TI

The Texas Instruments TPS25810ATWRVCRQ1 is an automotive USB Type-C downstream-facing port controller and power switch with digital cable compensation, a 3 A rated integrated USB power switch, and a 20-pin WQFN RVC package measuring 3 mm by 4 mm. It supports an operating temperature range of -40°C to 125°C and is positioned for automotive USB Type-C applications requiring integrated Type-C source control and power-path management. A USB Type-C DFP controller is an interface IC that coordinates USB Type-C connection orientation, advertises source capabilities, and manages the attached USB power path. Within the product hierarchy, it belongs to the USB Type-C controller class, then interface ICs, then semiconductor devices. By combining protocol control and a rated power switch in one package, the device can reduce the component count associated with automotive USB-C source ports while keeping connection and power-delivery functions together. The TPS25810A-Q1 family provides an integrated 3 A rated USB power switch, digital cable compensation, and Type-C source-controller functionality. Its automotive-qualified ordering designation identifies it for harsh operating environments. The 20-pin RVC WQFN package offers a compact surface-mount footprint, while the specified -40°C to 125°C range supports use across industrial temperature conditions common in vehicle electronics. Digital cable compensation is the principal differentiating function highlighted in the verified manufacturer materials. It allows the controller to address voltage-drop behavior associated with connected cables, helping the source side manage the electrical conditions of the USB Type-C link more effectively. The integrated switch also provides a defined current-handling point between the supply rail and the USB-C port, reducing the need for separate discrete protection and power-path elements in suitable architectures. Typical uses include automotive USB Type-C charging ports, vehicle infotainment connectivity, rear-seat accessory power, diagnostic interfaces, and USB-C service connections. The controller-and-switch combination is particularly useful where a compact source port is needed without allocating a separate Type-C controller and power switch. Vehicle designers must still verify connector requirements, cable current ratings, automotive qualification requirements, and system-level protection for every production design. When laying out the TPS25810ATWRVCRQ1, place the device and its required support components close to the USB Type-C connector and minimize high-current trace lengths. Validate connector, cable, and switch thermal performance under sustained load because a 3 A switch rating does not remove connector or wiring limitations. Confirm all pin functions against the current TI datasheet before layout release, as the verified excerpts do not provide the complete RVC pin map. This page combines the verified TI and distributor product information, package details, application guidance, and same-package replacement analysis for TPS25810ATWRVCRQ1. It also identifies engineering details that require confirmation from the full manufacturer datasheet rather than substituting assumptions for missing electrical, pinout, pricing, or compliance data.

詢價 聯絡我們
TPS25810TWRVCRQ1 - 3A USB Type-C DFP Controller | Texas Instruments
TPS25810TWRVCRQ1

TPS25810TWRVCRQ1 - 3A USB Type-C DFP Controller | Texas Instruments

Texas Instruments TPS25810TWRVCRQ1 is an automotive USB Type-C Rev. 1.2 downstream-facing port controller with an integrated 3 A power switch, load detection, and VCONN support in a 20-pin WQFN (RVC) package. The device is intended for USB Type-C source applications requiring configuration-channel control, port-attachment detection, and power-path switching. Its specified automotive operating-temperature range is -40°C to +105°C. A USB Type-C controller, also called a USB Type-C port controller, is a specialized interface IC that manages the configuration channel, commonly called CC, on a USB Type-C connector. Within the product hierarchy, it belongs to interface ICs and USB interface controllers. The downstream-facing-port role means the controller manages a port that supplies power and data-oriented Type-C behavior toward an attached upstream-facing port or cable. The TPS25810-Q1 family combines several functions in one device. It monitors the CC lines to determine when a Type-C attachment is present, integrates a power switch rated at 3 A, and includes load-detection capability. The verified product information also identifies VCONN functionality. When an electronically marked upstream-facing-port cable is attached, the controller can apply VCONN power to the cable's CC pin, supporting powered Type-C cables and attached accessories. The automotive grade distinguishes this orderable part from the commercial TPS25810 family option. The TPS25810TWRVCRQ1 is specified for -40°C to +105°C operation and uses the 20-terminal RVC WQFN package. The distributor listing identifies the package as 20-WQFN in a 3 mm by 4 mm footprint, while the manufacturer's ordering information identifies the package as WQFN (RVC). Typical uses include automotive USB Type-C charging ports, vehicle infotainment connections, USB Type-C docking interfaces, and downstream-facing ports that must identify attached accessories before enabling the power path. The integrated switch can reduce the external component count compared with a standalone Type-C controller and discrete power switch, although the final circuit still requires correct input protection, output discharge behavior, thermal layout, and connector wiring. Designers should follow the manufacturer's recommended application schematic and verify connector compatibility, CC pull-up or pull-down requirements, VCONN power limits, and exposed-pad soldering. Because the target is a downstream-facing-port controller, system-level USB data routing, host or device role implementation, and USB-PD policy must be confirmed against the complete product requirements rather than inferred from the controller alone. This page consolidates verified manufacturer and distributor information with package, interface-function, selection, and design guidance. It distinguishes documented facts from parameters that require confirmation from the full Texas Instruments datasheet, avoiding unsupported substitute, pinout, and pricing claims.

詢價 聯絡我們
TPS25820DSSR - USB-C Source Controller, 1.5A VBUS | Texas Instruments
TPS25820DSSR

TPS25820DSSR - USB-C Source Controller, 1.5A VBUS | Texas Instruments

The Texas Instruments TPS25820DSSR is a USB Type-C source controller and integrated 1.5 A VBUS power switch with VCONN support, housed in a 12-pin WSON (DSS) package. The device is designed for USB Type-C source applications that require Type-C attach detection, source-role control, VBUS current limiting, and an integrated power path. According to the Texas Instruments product and distributor information, the TPS25820DSSR operates from a 4.5 V to 5.5 V supply range and supports an operating temperature range from -40 °C to 125 °C. Its USB Type-C source-controller function is intended to simplify implementation in adapters, chargers, docks, and other USB-C power-delivery products. A USB Type-C source controller is a specialized interface and power-management IC that manages the behavior of a USB Type-C port when the device acts as a source or downstream-facing port. The TPS25820DSSR combines USB Type-C source detection and contract logic with an integrated 1.5 A VBUS switch, allowing a system to supply power to a connected USB-C sink while protecting the port against excessive current. In the broader component hierarchy, it belongs to the USB interface IC and power-management IC families rather than being a general-purpose logic device or standalone discrete MOSFET. The primary headline specifications are a 4.5 V to 5.5 V operating supply range, integrated 1.5 A VBUS power-switch capability, and a 12-WSON DSS package. The package is only 12 pins and is suitable for compact power-adapter and peripheral designs. The operating temperature range of -40 °C to 125 °C supports use across consumer, industrial, and temperature-qualified equipment, subject to the complete manufacturer datasheet for electrical limits and qualification details. The device also provides VCONN support, which is important for applications that need controlled VCONN behavior. TPS25820DSSR is positioned as a simple USB Type-C controller rather than a full USB Power Delivery policy engine. The Texas Instruments product page describes it as a USB Type-C source controller with an integrated 1.5 A USB VBUS power switch, while the TPS25820 evaluation module provides reference circuitry for evaluating the controller. Designers should therefore verify the required USB Type-C behavior, sink advertisement method, VCONN implementation, and fault-handling requirements against the datasheet before finalizing a product architecture. Typical uses include USB-C wall adapters, charging cables and power modules, docking stations, laptop and tablet charging accessories, industrial USB-C power supplies, and compact USB-C peripheral designs. The integrated switch can reduce the number of external power-path components when the design requires a modest 1.5 A source capability. A designer selecting a higher-current USB-C source solution would need a different controller and power-switch architecture rather than assuming that TPS25820DSSR can deliver more than its specified 1.5 A. The principal design consideration is the relationship between the external USB-C connector, input supply, output power path, and the controller's internal protection functions. The input supply must remain within the verified 4.5 V to 5.5 V range, and layout should minimize high-current loop area between the switch, connector, and capacitors. Decoupling, current-limit behavior, VCONN routing, thermal performance, and the exposed-pad grounding requirements must be checked in the manufacturer datasheet and evaluation-module layout. This product summary combines verified manufacturer and distributor information, package and application context, comparison guidance, and practical implementation notes to help engineers evaluate TPS25820DSSR for USB Type-C source designs beyond a basic catalog description.

詢價 聯絡我們
TPS25821DSST - 1.5A USB Type-C Source Controller | Texas Instruments
TPS25821DSST

TPS25821DSST - 1.5A USB Type-C Source Controller | Texas Instruments

Texas Instruments TPS25821DSST is a USB Type-C source controller and 1.5A power switch with a 12-WSON (3x2) DSS package. It operates from -40°C to +125°C and is designed for USB Type-C source applications that require connection-oriented charging behavior. The device combines Type-C source-controller functionality with integrated 1.5A power-switch capability in one compact package. A USB Type-C source controller is an interface IC within the USB Type-C and power-delivery ecosystem. It identifies a Type-C attach event, applies the appropriate source behavior, and helps manage power to a connected USB device. Within the broader hierarchy, the TPS25821 is a USB interface controller, power-management IC, and semiconductor designed to coordinate connector detection with controlled power delivery. The headline specifications are a 1.5A rated power switch, a 12-WSON (3x2) package, and an operating temperature range of -40°C to +125°C. The manufacturer identifies the device as a USB Type-C source controller and power switch. Its Rev. C family datasheet also documents the TPS25820 companion family, providing a common technical reference for designers evaluating the source-controller family. The integrated source-controller and switch architecture reduces the number of separate power-path components required for a USB Type-C source design. According to the TPS25821 product page, the PMP40260 reference design uses this device family to provide 5V at 1.5A to a USB Type-C device while also supporting a legacy device that uses DCP charging behavior. This makes the device applicable where a compact Type-C source port must support both modern Type-C and legacy charging paths. Typical uses include USB Type-C docking stations, laptop and tablet charging ports, power banks, industrial USB power-delivery equipment, monitor USB power ports, and multiport charging accessories. The -40°C to +125°C temperature range supports applications extending beyond room-temperature consumer accessories. The package is especially useful where connector density and board area limit the available component footprint. Designers should review the manufacturer datasheet and the PMP40260 reference design before finalizing input protection, output capacitance, current limiting, thermal layout, and USB Type-C advertising. Because the retrieved data does not specify a complete pin map, input and output voltage limits, switch resistance, logic thresholds, or capacitor requirements, those values must be confirmed directly from the manufacturer documentation rather than inferred from the product category. This product page consolidates the verified manufacturer description, distributor availability, package information, temperature range, reference-design context, and engineering selection guidance. It also clearly separates known facts from unavailable detailed specifications and avoids presenting generic USB Type-C characteristics as verified TPS25821DSST specifications.

詢價 聯絡我們
TPS3430WQDRCRQ1 - Automotive Window Watchdog | Texas Instruments
TPS3430WQDRCRQ1

TPS3430WQDRCRQ1 - Automotive Window Watchdog | Texas Instruments

Texas Instruments TPS3430WQDRCRQ1 is an automotive window watchdog timer with programmable watchdog window and programmable watchdog reset delay, supplied in a 10-VSON package measuring 3.00 mm by 3.00 mm. The device is designed to supervise automotive electronic systems by detecting both late service activity and activity outside a configured timing window. Its operating-temperature range is -40°C to +125°C, and the package uses wettable flanks for optical inspection. A window watchdog timer is a specialized form of watchdog timer that requires the monitored system to toggle its service signal within both an upper and lower timing boundary. Unlike a conventional timeout-only watchdog, a window watchdog can identify both a frozen system and operation that occurs too quickly. This makes it valuable in automotive controllers where correct task scheduling and deterministic control-loop activity must be verified. The TPS3430-Q1 family provides programmable watchdog timing and programmable reset delay. Its SET pins can disable the watchdog during development or power-on sequences, preventing unintended timeout events before the monitored application is ready. The small 3.00 mm × 3.00 mm 10-VSON package supports compact automotive control modules while wettable flanks improve assembly inspection. The TPS3430WQDRCRQ1 belongs to the clock and timing IC hierarchy as a supervisory timing device. Its watchdog window mechanism operates alongside the host processor rather than replacing it: the host must service the watchdog within the permitted interval, while the timer supplies a fault indication when service is missing, too early, or too late. The programmable reset delay adds a controlled response interval after a watchdog event. Typical uses include automotive body controllers, motor-control modules, battery-management systems, electronic control units, and other safety-relevant embedded platforms. Its -40°C to +125°C rating and automotive-oriented ordering designation make it suitable for designs operating across extended industrial temperatures. For automotive production designs, engineers should also verify the complete device qualification and documentation package rather than relying only on the ordering code. PCB implementation should place the watchdog and its associated bypass capacitor close to the host controller and power-entry circuitry. Keep the monitored service signal away from noisy power and switching-node routing, and validate both reset polarity and timeout behavior in the complete firmware state machine. The watchdog must remain disabled only during controlled startup or programming intervals. This page consolidates the verified manufacturer and distributor information, distinguishes the automotive window watchdog function from ordinary timeout devices, and provides practical selection, comparison, and design guidance. Exact electrical limits, threshold ranges, pin functions, qualification details, and volume pricing should be confirmed against the current manufacturer documentation before design release.

詢價 聯絡我們
TPS3700DDCR2 - 18V Window Comparator | Texas Instruments
TPS3700DDCR2

TPS3700DDCR2 - 18V Window Comparator | Texas Instruments

The Texas Instruments TPS3700DDCR2 is an 18 V window voltage detector with two high-accuracy comparators, an internal 400 mV reference, and two open-drain outputs rated to 18 V, packaged in the 6-pin SOT-23-THIN package. It monitors supply voltages from 1.8 V to 18 V and supports overvoltage and undervoltage detection. A window voltage detector compares a monitored supply against internally generated upper and lower thresholds. It can operate as a two-channel window comparator or as two independent voltage monitors. This device belongs to the comparator hierarchy, combines a voltage detector function with a precision internal reference, and sits within the broader power management semiconductor and system monitoring categories. The TPS3700DDCR2 provides two separate open-drain indication outputs, allowing a system to identify both undervoltage and overvoltage conditions. Its 18 V output rating supports monitoring applications above the voltage range commonly handled by basic low-voltage comparator ICs. The internal 400 mV reference provides the basis for externally programmed detection thresholds. Both comparators include built-in hysteresis according to the manufacturer product information. Hysteresis helps reject brief input disturbances and improves output stability when the monitored voltage is close to a threshold. The device can be configured through external components for different supply ranges, reducing the need for a separate precision reference when the application requires upper and lower fault detection. Typical uses include industrial equipment monitoring, battery-powered systems, communication equipment, consumer electronics, and power rails where the system must disable downstream circuitry during an invalid voltage condition. The two independent outputs can also support separate fault-reporting paths in redundant or multi-rail architectures. When designing the circuit, calculate the resistor-defined upper and lower thresholds against the monitored input range, and verify that every pulled-up open-drain output remains below its 18 V rating. The SOT-23-THIN package also requires careful PCB layout and thermal review when the surrounding circuitry or board raises the device temperature. This product page combines verified manufacturer and distributor information with pin-compatible alternatives, parameter comparisons, application guidance, and practical design notes so engineers can evaluate the TPS3700DDCR2 alongside replacement options without treating merely similar supervisors as exact drop-in parts.

詢價 聯絡我們
TPS3700DDCT - 18V Window Comparator | Texas Instruments
TPS3700DDCT

TPS3700DDCT - 18V Window Comparator | Texas Instruments

The Texas Instruments TPS3700DDCT is an 18 V window voltage comparator with a 400 mV internal reference, two open-drain outputs, and a 6-pin SOT-23-THIN package. It operates from 1.8 V to 18 V and monitors one rail for overvoltage and undervoltage conditions. Its adjustable thresholds can extend detection down to 400 mV, while the open-drain outputs are rated to 18 V. A window comparator is a voltage supervisor that combines two threshold comparisons around a monitored signal. It belongs to the comparator and power-management IC hierarchy, where it is used to identify when a supply enters an allowed operating window or exits it because of an excessive low or high condition. The TPS3700 can therefore operate as a combined window detector or as two independent voltage monitors. Key features include a wide 1.8 V to 18 V supply range, threshold accuracy of -1.0% over temperature, 0.25% typical threshold accuracy, and 5.5 uA typical quiescent current. The two open-drain outputs can be pulled up to an external voltage up to 18 V. Built-in hysteresis helps reject brief glitches and maintain stable outputs, while external resistors set the monitored voltage range. The TPS3700DDCT uses two high-accuracy comparators and an internal 400 mV reference. One comparator monitors the lower threshold and the other monitors the upper threshold, allowing detection of undervoltage and overvoltage separately. The monitored voltage is scaled with external resistors, making the device suitable for systems where the rail is higher than the internal reference. Typical applications include industrial 24 V input-bus monitoring, battery-pack protection, DC power-supply fault detection, load-switch sequencing, and embedded systems that require a hardware voltage supervisor. Its low quiescent current is useful in battery-powered equipment, while the 18 V operating range supports higher-voltage industrial rails. When designing the circuit, choose resistor values to keep the sense-node voltage within the comparator input limits and use pull-up resistors appropriate for the open-drain outputs. Confirm the logic polarity of both outputs in the system controller because a fault indication can require inversion. Review the manufacturer datasheet for threshold, hysteresis, input-current, and absolute-maximum details before finalizing the PCB layout.

詢價 聯絡我們
TPS3700DSET - 18V Window Voltage Detector | Texas Instruments
TPS3700DSET

TPS3700DSET - 18V Window Voltage Detector | Texas Instruments

The Texas Instruments TPS3700DSET is a high-voltage (18 V) window voltage detector for overvoltage and undervoltage monitoring, featuring two high-accuracy comparators with an internal 400 mV reference and two open-drain outputs rated to 18 V. It is offered in a 6-pin WSON package measuring 1.5 mm x 1.5 mm with a propagation delay of 29 us (maximum). A window voltage detector is a type of voltage supervisor or comparator circuit that monitors an input rail and asserts an alert whenever the rail falls outside a programmer-defined upper and lower threshold. It belongs to the broader family of comparators (amplifier ICs) which sit within power management ICs, and is commonly used as a safety watchdog in microprocessor and DSP power systems. Compared to single-threshold comparators, the window detector adds redundancy by failing-fast on both excursions, which is critical for ASIC rails, battery stacks, and industrial 24 V systems. Key features include a wide supply voltage range of 1.8 V to 18 V, threshold accuracy of 1.0% over temperature (0.25% typical), a low quiescent current of 5.5 uA typical, and built-in hysteresis on both comparators to reject brief glitches without false triggering. The monitored thresholds are set via external resistor dividers referenced to the internal 400 mV band-gap, and the two open-drain outputs can be pulled up to as high as 18 V for direct interface to logic rails or opto-isolators. The TPS3700DSET uses a CMOS architecture with a precision bandgap reference and twin comparators, giving it a clean offset and temperature-stable trip point across the -40C to +125C junction temperature range. The wide supply tolerance also lets it operate directly from 12 V and 15 V industrial rails without pre-regulation. Typical applications include overvoltage and undervoltage monitoring on 12 V industrial rails, battery-pack protection in multi-cell stacks, system reset generation for DSPs and microcontrollers, fault detection in PLC and motor-drive systems, and redundant safety supervision in medical and automotive subsystems. When designing with this device, choose the resistor divider ratio so the monitored voltage equals 400 mV at the desired trip point; hysteresis is fixed by internal design, but selection of the resistor network affects overall accuracy and input bias current error. This page consolidates verified distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the TPS3700DSET as a window supervisor.

詢價 聯絡我們