產品(44,000+)

STM32G030C6T6TR - Cortex-M0+ MCU, 64MHz, 32KB Flash, LQFP-48 (Tape & Reel)
STM32G030C6T6TR

STM32G030C6T6TR - Cortex-M0+ MCU, 64MHz, 32KB Flash, LQFP-48 (Tape & Reel)

The STMicroelectronics STM32G030C6T6TR is a 32-bit Arm Cortex-M0+ mainstream microcontroller operating at up to 64 MHz, offering 32 KB of Flash and 8 KB of SRAM in a 48-pin LQFP (7x7 mm) package. It is part of the STM32G0 value-line series designed for cost-sensitive embedded applications requiring modern peripherals and low power consumption. An Arm Cortex-M0+ microcontroller is a low-power 32-bit processor core based on the Armv6-M architecture, optimized for energy-efficient embedded designs. It belongs to the broader category of microcontrollers (MCUs), which integrate CPU, memory, and peripherals on a single die. The Cortex-M0+ sits below Cortex-M3/M4 in performance but excels at deterministic interrupt response and minimal energy per instruction, making it ideal for sensor nodes, human-machine interfaces (HMI), and battery-powered consumer devices. The STM32G0 family represents ST's entry-level mainstream line, balancing 8-bit MCU cost with 32-bit performance. Key features include the Cortex-M0+ core with single-cycle I/O access, hardware CRC, real-time clock, low-power Run/Stop/Standby/Shutdown modes, and an operating temperature range of -40C to +85C. The device integrates an 11-channel 12-bit ADC (2.5 Msps), multiple timers, and serial interfaces including USART, SPI, and I2C (with Fast-mode Plus support up to 1 Mbit/s). The integrated voltage regulator and brown-out reset simplify power-supply design across 2.0V to 3.6V supplies. Technical depth: the STM32G030C6T6TR uses ST's 90 nm process with on-chip voltage scaling, achieving typical Run-mode current under 1 mA/MHz and Stop-mode current in the microamp range. The single-wire debug (SWD) interface and integrated bootloader shorten firmware bring-up. Hardware parity on SRAM catches single-bit faults in safety-relevant code. Typical applications include small appliance controls, USB Type-C cable marker ICs, simple HMI panels (buttons, LEDs), and sensor hubs. The wide operating voltage allows direct battery connection in 2xAA or coin-cell systems. Design consideration: leverage the LQFP-48 (7x7 mm) package's exposed pad for thermal relief; if unused, leave it floating or stitch to ground per ST's design recommendations. This page combines authoritative ST datasheet data, drop-in alternates, and practical design notes to support engineer selection and second-sourcing decisions.

詢價 聯絡我們
STM32G030C8T6 - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics
STM32G030C8T6

STM32G030C8T6 - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics

The STM32G030C8T6 is a 32-bit ARM Cortex-M0+ based microcontroller from STMicroelectronics, featuring 64KB of Flash memory and 8KB of SRAM. It operates at a maximum clock frequency of 64 MHz and is housed in a 48-pin LQFP package (7x7 mm). This device is part of the STM32G0 series, designed for cost-sensitive and power-efficient applications. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single chip. It is the brain of embedded systems, executing instructions to control devices such as sensors, motors, and displays. In the system hierarchy, a microcontroller falls under embedded processors, which are part of the broader category of integrated circuits. The STM32G030C8T6 is a mainstream MCU, balancing performance, power consumption, and cost for a wide range of applications. Key features include a 12-bit ADC with up to 19 channels, multiple timers (including advanced-control timers), and a rich set of communication interfaces: I2C, SPI, USART, and low-power UART. The device supports a supply voltage range of 2.0V to 3.6V and offers multiple low-power modes (Sleep, Stop, Standby) to optimize energy consumption. It also includes a DMA controller, CRC calculation unit, and a real-time clock (RTC). The STM32G030C8T6 is built on a high-performance ARM Cortex-M0+ core with a single-cycle multiplier and a nested vectored interrupt controller (NVIC). It features a memory protection unit (MPU) for enhanced security and reliability. The device is supported by ST's comprehensive ecosystem, including the STM32CubeMX configuration tool and the STM32CubeG0 firmware library, which accelerate development. Typical applications include industrial control systems, consumer electronics, IoT devices, home automation, and battery-powered equipment. Its low power consumption and rich peripheral set make it suitable for sensor hubs, motor control, and human-machine interfaces (HMI). When designing with this MCU, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to the VDD pins. For low-power applications, utilize the Stop and Standby modes to reduce current consumption to microamp levels. The device is RoHS compliant and available in tape and reel packaging for automated assembly.

USD $1.47 聯絡我們
STM32G030C8T6TR - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics (Tape & Reel)
STM32G030C8T6TR

STM32G030C8T6TR - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics (Tape & Reel)

The STM32G030C8T6TR is a 32-bit ARM Cortex-M0+ based microcontroller from STMicroelectronics, featuring 64KB of Flash memory and 8KB of SRAM. It operates at a maximum clock frequency of 64 MHz and is housed in a 48-pin LQFP package (7x7 mm). This device is part of the STM32G0 series, designed for cost-sensitive and power-efficient applications. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single chip. It is the brain of embedded systems, executing instructions to control devices such as sensors, motors, and displays. In the system hierarchy, a microcontroller falls under embedded processors, which are part of the broader category of integrated circuits. The STM32G030C8T6TR is a mainstream MCU, balancing performance, power consumption, and cost for a wide range of applications. Key features include a 12-bit ADC with up to 19 channels, multiple timers (including advanced-control timers), and a rich set of communication interfaces: I2C, SPI, USART, and low-power UART. The device supports a supply voltage range of 2.0V to 3.6V and offers multiple low-power modes (Sleep, Stop, Standby) to optimize energy consumption. It also includes a DMA controller, CRC calculation unit, and a real-time clock (RTC). The STM32G030C8T6TR is built on a high-performance ARM Cortex-M0+ core with a single-cycle multiplier and a nested vectored interrupt controller (NVIC). It features a memory protection unit (MPU) for enhanced security and reliability. The device is supported by ST's comprehensive ecosystem, including the STM32CubeMX configuration tool and the STM32CubeG0 firmware library, which accelerate development. Typical applications include industrial control systems, consumer electronics, IoT devices, home automation, and battery-powered equipment. Its low power consumption and rich peripheral set make it suitable for sensor hubs, motor control, and human-machine interfaces (HMI). When designing with this MCU, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to the VDD pins. For low-power applications, utilize the Stop and Standby modes to reduce current consumption to microamp levels. The device is RoHS compliant and available in tape and reel packaging for automated assembly.

USD $1.47 聯絡我們
STM32G030F6P6 - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics
STM32G030F6P6

STM32G030F6P6 - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics

The STM32G030F6P6 is a mainstream 32-bit microcontroller from STMicroelectronics, built on the high-performance Arm® Cortex®-M0+ RISC core operating at up to 64 MHz. It features 32 KB of Flash memory and 8 KB of SRAM with hardware parity, housed in a compact 20-pin TSSOP package. This device is designed for cost-sensitive, mass-production applications, offering a balanced combination of performance, memory, and peripheral integration. What is a microcontroller (MCU)? A microcontroller is a compact integrated circuit designed to govern a specific operation in an embedded system. It integrates a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. The STM32G030F6P6 belongs to the STM32G0 series, which is part of the broader STM32 family of 32-bit Arm Cortex-M microcontrollers. This hierarchy positions it as a mainstream, entry-level MCU within the STM32 ecosystem, ideal for applications ranging from simple control loops to more complex sensor and communication tasks. Key features of the STM32G030F6P6 include a 64 MHz Arm Cortex-M0+ core, 32 KB Flash, 8 KB SRAM, and a 2.0V to 3.6V supply range. It integrates a rich set of peripherals: I2C (with Fast-mode Plus up to 1 Mbit/s), USART, SPI, a 12-bit ADC, timers, and GPIOs. The device also supports a wide operating temperature range and is available in a 20-pin TSSOP package, making it suitable for space-constrained designs. Technically, the STM32G030F6P6 leverages the energy-efficient Cortex-M0+ architecture, which balances processing capability with low power consumption. The inclusion of hardware parity on SRAM enhances data integrity, a critical feature for safety-conscious applications. The I2C interface supports Standard-mode (100 kbit/s), Fast-mode (400 kbit/s), and Fast-mode Plus (1 Mbit/s), providing flexible communication options. The 12-bit ADC enables precise analog signal acquisition, essential for sensor-based applications. Typical applications include industrial control, consumer electronics, IoT devices, and simple automation systems. Its low cost and small footprint make it an excellent choice for high-volume products such as smart sensors, motor control, and portable devices. The wide supply voltage range and robust peripheral set ensure versatility across diverse use cases. When designing with this MCU, consider the 2.0V to 3.6V supply range and ensure proper decoupling with a 100nF capacitor close to each power pin. The 20-pin TSSOP package requires careful PCB layout to minimize noise, especially for the ADC and high-speed I2C lines. Refer to the STM32G030F6 datasheet for detailed electrical characteristics and recommended layout guidelines.

詢價 聯絡我們
STM32G030F6P6TR - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics (Tape & Reel)
STM32G030F6P6TR

STM32G030F6P6TR - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics (Tape & Reel)

The STM32G030F6P6TR is a mainstream 32-bit microcontroller from STMicroelectronics, built on the high-performance Arm® Cortex®-M0+ RISC core operating at up to 64 MHz. It features 32 KB of Flash memory and 8 KB of SRAM with hardware parity, housed in a compact 20-pin TSSOP package. This device is designed for cost-sensitive, mass-production applications, offering a balanced combination of performance, memory, and peripheral integration. What is a microcontroller (MCU)? A microcontroller is a compact integrated circuit designed to govern a specific operation in an embedded system. It integrates a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. The STM32G030F6P6TR belongs to the STM32G0 series, which is part of the broader STM32 family of 32-bit Arm Cortex-M microcontrollers. This hierarchy positions it as a mainstream, entry-level MCU within the STM32 ecosystem, ideal for applications ranging from simple control loops to more complex sensor and communication tasks. Key features of the STM32G030F6P6TR include a 64 MHz Arm Cortex-M0+ core, 32 KB Flash, 8 KB SRAM, and a 2.0V to 3.6V supply range. It integrates a rich set of peripherals: I2C (with Fast-mode Plus up to 1 Mbit/s), USART, SPI, a 12-bit ADC, timers, and GPIOs. The device also supports a wide operating temperature range and is available in a 20-pin TSSOP package, making it suitable for space-constrained designs. Technically, the STM32G030F6P6TR leverages the energy-efficient Cortex-M0+ architecture, which balances processing capability with low power consumption. The inclusion of hardware parity on SRAM enhances data integrity, a critical feature for safety-conscious applications. The I2C interface supports Standard-mode (100 kbit/s), Fast-mode (400 kbit/s), and Fast-mode Plus (1 Mbit/s), providing flexible communication options. The 12-bit ADC enables precise analog signal acquisition, essential for sensor-based applications. Typical applications include industrial control, consumer electronics, IoT devices, and simple automation systems. Its low cost and small footprint make it an excellent choice for high-volume products such as smart sensors, motor control, and portable devices. The wide supply voltage range and robust peripheral set ensure versatility across diverse use cases. When designing with this MCU, consider the 2.0V to 3.6V supply range and ensure proper decoupling with a 100nF capacitor close to each power pin. The 20-pin TSSOP package requires careful PCB layout to minimize noise, especially for the ADC and high-speed I2C lines. Refer to the STM32G030F6 datasheet for detailed electrical characteristics and recommended layout guidelines.

詢價 聯絡我們
STM32G030J6M6 - 64MHz Cortex-M0+ 32KB Flash MCU | STMicroelectronics
STM32G030J6M6

STM32G030J6M6 - 64MHz Cortex-M0+ 32KB Flash MCU | STMicroelectronics

STMicroelectronics STM32G030J6M6 is an Arm Cortex-M0+ 32-bit microcontroller operating up to 64 MHz, with 32 KB of Flash memory, 8 KB of RAM, and six I/O pins in an 8-SOIC package. The device belongs to the STM32G0 mainstream value-line family and is positioned for compact, cost-sensitive embedded control designs that need efficient 32-bit processing without a large package. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripheral interfaces, and I/O circuitry on one device. In the product hierarchy, the STM32G030J6M6 is an MCU, then a 32-bit microcontroller, then an embedded processor based on the Arm Cortex-M0+ architecture. This combination supports compact control logic, real-time peripheral operation, and efficient firmware execution in industrial, consumer, and embedded systems. Key features include a 64 MHz Arm Cortex-M0+ core, 32 KB Flash, 8 KB SRAM, and six I/O pins. The STM32G030 family provides I2C capability supporting Standard mode, Fast mode, and Fast mode Plus according to the manufacturer datasheet. The small SOIC package and six-pin I/O count are useful when board space is constrained, although the limited pin budget requires careful prioritization of communication, timing, and control signals. The STM32G030x6/x8 devices use the high-performance 32-bit Arm Cortex-M0+ RISC core. The M0+ architecture is designed for efficient embedded operation and supports deterministic control in applications where response time and power-conscious code execution are important. Compared with larger STM32 families, the G030 devices target mainstream value-line designs where 32 KB Flash and 8 KB RAM are sufficient for the product function. Typical uses include compact sensor-control boards, industrial automation modules, appliance controls, and low-cost communication peripherals. A designer should partition the six available I/O pins among required serial functions, control outputs, and interrupts, then verify that the selected peripheral multiplexing remains consistent with the board architecture. The principal design consideration is footprint planning. The 8-SOIC package simplifies assembly but offers only six I/O pins, so a design needing more external signals should consider a larger STM32G0 package rather than force costly signal multiplexing. Confirm power, decoupling, programming, reset, and clock requirements against the manufacturer datasheet before layout release. This product analysis combines the verified STMicroelectronics family data, distributor specifications, source documentation, and practical selection guidance into a concise engineering reference for cost-conscious embedded control applications.

詢價 聯絡我們
STM32G030K6T6 64MHz 32KB MCU 32-LQFP | STMicroelectronics
STM32G030K6T6

STM32G030K6T6 64MHz 32KB MCU 32-LQFP | STMicroelectronics

The STMicroelectronics STM32G030K6T6 is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 64 MHz, with 32 KB of Flash memory and 8 KB of SRAM, housed in a 32-LQFP 7 x 7 mm package. It belongs to the STM32G0 mainstream value line and combines a compact general-purpose MCU package with embedded memory and peripheral connectivity for embedded control designs. What is a microcontroller? A microcontroller is a semiconductor device that integrates a processor core, memory, and peripheral interfaces into one component. An Arm Cortex-M0+ core provides a compact, energy-efficient architecture for real-time control tasks, while the STM32G0 family sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic-control component categories. The STM32G030K6T6 provides the verified headline resources of 64 MHz operating frequency, 32 KB Flash, and 8 KB SRAM. The 32-LQFP package exposes the device in a 7 x 7 mm surface-mount form factor suitable for compact control boards. Its mainstream value-line positioning makes it applicable to cost-sensitive embedded products where a small, general-purpose 32-bit MCU is sufficient. The Arm Cortex-M0+ processor architecture supports firmware-driven control without requiring a separate processor, while integrated Flash and SRAM reduce the number of external memory components in simpler designs. Exact peripheral counts, voltage limits, I/O ratings, and electrical timing values are not included in the supplied verified snippets and are therefore not asserted here. Typical application domains include industrial control, consumer electronics, small embedded controllers, sensor interfaces, and compact automation products. The verified product information identifies industrial control and consumer electronics as common applications, and the 64 MHz core and 32 KB memory footprint provide a clear platform for embedded logic, peripheral coordination, and control-loop software. Designers should verify the complete electrical limits, pin multiplexing, clock configuration, memory programming requirements, and package drawing in the official STMicroelectronics product documentation before layout release. For a purchase decision, compare the required peripheral mix and software ecosystem against the exact device revision and package variant. This product summary consolidates the verified manufacturer identity, distributor specifications, package information, and application context. Pricing and availability remain subject to distributor confirmation as of 2026-10-22, while detailed technical values not present in the supplied data are deliberately left for datasheet verification.

詢價 聯絡我們
STM32G030K6T6TR 64MHz 32KB MCU 32-LQFP | STMicroelectronics (Tape & Reel)
STM32G030K6T6TR

STM32G030K6T6TR 64MHz 32KB MCU 32-LQFP | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32G030K6T6TR is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 64 MHz, with 32 KB of Flash memory and 8 KB of SRAM, housed in a 32-LQFP 7 x 7 mm package. It belongs to the STM32G0 mainstream value line and combines a compact general-purpose MCU package with embedded memory and peripheral connectivity for embedded control designs. What is a microcontroller? A microcontroller is a semiconductor device that integrates a processor core, memory, and peripheral interfaces into one component. An Arm Cortex-M0+ core provides a compact, energy-efficient architecture for real-time control tasks, while the STM32G0 family sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic-control component categories. The STM32G030K6T6TR provides the verified headline resources of 64 MHz operating frequency, 32 KB Flash, and 8 KB SRAM. The 32-LQFP package exposes the device in a 7 x 7 mm surface-mount form factor suitable for compact control boards. Its mainstream value-line positioning makes it applicable to cost-sensitive embedded products where a small, general-purpose 32-bit MCU is sufficient. The Arm Cortex-M0+ processor architecture supports firmware-driven control without requiring a separate processor, while integrated Flash and SRAM reduce the number of external memory components in simpler designs. Exact peripheral counts, voltage limits, I/O ratings, and electrical timing values are not included in the supplied verified snippets and are therefore not asserted here. Typical application domains include industrial control, consumer electronics, small embedded controllers, sensor interfaces, and compact automation products. The verified product information identifies industrial control and consumer electronics as common applications, and the 64 MHz core and 32 KB memory footprint provide a clear platform for embedded logic, peripheral coordination, and control-loop software. Designers should verify the complete electrical limits, pin multiplexing, clock configuration, memory programming requirements, and package drawing in the official STMicroelectronics product documentation before layout release. For a purchase decision, compare the required peripheral mix and software ecosystem against the exact device revision and package variant. This product summary consolidates the verified manufacturer identity, distributor specifications, package information, and application context. Pricing and availability remain subject to distributor confirmation as of 2026-10-22, while detailed technical values not present in the supplied data are deliberately left for datasheet verification.

詢價 聯絡我們
STM32G030K8T6 - 64MHz Cortex-M0+ MCU, 64KB Flash | ST
STM32G030K8T6

STM32G030K8T6 - 64MHz Cortex-M0+ MCU, 64KB Flash | ST

The STMicroelectronics STM32G030K8T6 is a mainstream 32-bit microcontroller based on an Arm Cortex-M0+ core running at up to 64 MHz, with 64 KB Flash memory and 8 KB SRAM, housed in a 32-pin LQFP (7x7 mm) package. An MCU (microcontroller unit) is a single-chip computer that integrates a processor core, program memory, data memory, and peripheral interfaces into one IC. Within the microcontroller hierarchy, the STM32G030K8T6 belongs to the STM32 mainstream value-line family, positioned as a cost-optimized entry point into the broader STM32 ecosystem and general-purpose embedded processor market. Key features include the high-performance Cortex-M0+ 32-bit RISC core at 64 MHz, 64 KB of embedded Flash with ECC option, 8 KB of SRAM, and flexible connectivity peripherals. The device integrates USART, I2C (Standard-mode 100 kbit/s, Fast-mode 400 kbit/s, and Fast-mode Plus 1 Mbit/s per the I2C-bus specification rev. 5 compatibility noted in the ST datasheet), and SPI interfaces, plus a 12-bit ADC, timers, and a real-time clock calendar. Operating from a 2.0V to 3.6V supply, it suits battery-powered and industrial designs. Technically, the STM32G0 Series leverages ST's 90 nm embedded-Flash process and an ART-accelerated memory interface, achieving efficient zero-wait-state execution for most code paths. The low-power modes (Sleep, Stop, Standby) reduce consumption for always-on applications, and the core keeps legacy 8/16-bit MCU workloads simple while offering 32-bit performance. Typical applications include industrial automation, consumer appliances, IoT sensor nodes, power tools, and simple motor-control tasks where cost and low power matter more than maximum processing throughput. When designing, budget the 8 KB SRAM carefully, as it is the most common constraint when scaling firmware; enable the hardware ECC and brown-out reset options to harden safety-critical code. This page synthesizes distributor pricing, pin-to-pin family alternatives, and practical design notes not found on a single manufacturer or distributor page.

詢價 聯絡我們
STM32G031C4T6 32-Bit Cortex-M0+ MCU | STMicroelectronics
STM32G031C4T6

STM32G031C4T6 32-Bit Cortex-M0+ MCU | STMicroelectronics

STMicroelectronics STM32G031C4T6 is a 32-bit Arm Cortex-M0+ general-purpose microcontroller in the STM32G0 series, supplied in a 48-pin LQFP package. It is designed for compact embedded systems that require efficient control, serial connectivity, and low-power operation without the complexity of a larger microcontroller. This product page is data-limited because the supplied distributor search returned a timeout and no component records were retrieved. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and communication interfaces on one integrated circuit. The STM32G0 family occupies the practical low-end portion of the STM32 portfolio, providing general-purpose processing for cost-sensitive industrial, consumer, appliance, sensor, and automation products. Its Arm Cortex-M0+ architecture provides a common instruction set and software ecosystem while supporting deterministic control tasks. The STM32G031C4T6 family designation identifies the device family, device geometry, flash-density option, package code, and temperature-grade option. Exact flash capacity, SRAM capacity, clock rate, operating-voltage range, GPIO count, converter performance, communication peripherals, and environmental limits were not present in the verified records supplied for this generation. Those parameters are therefore marked as requiring confirmation rather than estimated from the MPN or from unverified distributor content. Typical uses include low-cost sensor nodes, compact motor-control boards, appliance controllers, building equipment, and communication-enabled embedded products. In these systems, the device can execute firmware, acquire sensor data, control discrete outputs, and manage a local serial interface. Exact peripheral allocation and timing limits must be checked against the official manufacturer datasheet before final schematic or firmware design. The primary design consideration is footprint and resource planning. A replacement should match the 48-pin LQFP land pattern, power requirements, clock architecture, memory requirements, pin multiplexing, and temperature grade. Pin-compatible packages alone do not guarantee functional equivalence, so exposed-pin and peripheral differences require circuit-level verification. This page distinguishes verified identity information from unverified technical claims, consolidates the available manufacturer resource, and identifies the exact data still needed for design qualification, comparison, procurement, and drop-in replacement decisions.

詢價 聯絡我們
STM32G031C4U6 - 64MHz Cortex-M0+ MCU | STMicroelectronics
STM32G031C4U6

STM32G031C4U6 - 64MHz Cortex-M0+ MCU | STMicroelectronics

STMicroelectronics STM32G031C4U6 is a 32-bit ARM Cortex-M0+ microcontroller with a 64 MHz processor, 16 KB of embedded Flash memory, 8 KB of SRAM, and a 48-pin UFQFPN package with an exposed pad. It operates from a 1.7 V to 3.6 V supply range, making it suitable for compact embedded-control, analog-monitoring, and general-purpose industrial designs. A microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, and peripherals such as analog-to-digital converters, timers, communication interfaces, and GPIO into one package. The STM32G031 belongs to the STM32G0 family and the ARM Cortex-M0+ hierarchy, where the simplified Cortex-M0+ core is designed for efficient, low-cost real-time control. In system terms, it is a microcontroller MCU and embedded-control IC rather than a general-purpose processor. The verified configuration emphasizes a practical balance of processing speed, memory, and analog capability. Its maximum CPU frequency is 64 MHz, its Flash organization is 16K x 8, and its SRAM capacity is 8 KB. The device includes a 12-bit ADC according to the distributor data. Its 1.7 V minimum operating voltage permits use in low-voltage equipment, while the 3.6 V maximum supports conventional 3.3 V systems when appropriate decoupling and voltage regulation are applied. The STM32G031C4U6 combines a single Cortex-M0+ processing core with 16 KB of Flash and 8 KB of SRAM. Its 48-UFQFPN exposed-pad package supports compact PCB layouts, but the exposed pad must be connected to the ground plane as specified by the manufacturer. The 12-bit ADC is useful for reading potentiometers, sensors, and other analog inputs, while GPIO and embedded-control functions support common industrial-control tasks. Typical uses include compact sensor controllers, analog monitoring modules, low-power monitoring equipment, basic serial-interface control systems, and small industrial automation nodes. Designers should use the STM32G0 ecosystem for peripheral configuration and firmware development. Because the available verified data does not enumerate every peripheral, timer, communication interface, pin, or ADC channel, those details should be confirmed in the official STM32G031 documentation before final schematic and firmware decisions. The main design consideration is to preserve signal and power integrity around the exposed-pad device. Place the decoupling capacitors close to their associated supply pins, provide an uninterrupted ground connection beneath the exposed pad, and route high-current or switching signals away from sensitive analog inputs. Confirm the exact pin multiplexing and alternate-function assignments in the official datasheet because the supplied search data confirms the 48-pin package but not the complete pinout. This page consolidates the verified distributor specifications, sourcing information, application guidance, and verified availability context into a design-focused reference. It also clearly separates confirmed facts from parameters that still require the manufacturer datasheet, helping engineers evaluate the STM32G031C4U6 without assuming unverified pin, peripheral, lifecycle, or compliance details.

詢價 聯絡我們
STM32G031C6T6 - 64MHz Cortex-M0+ 32KB MCU | STMicroelectronics
STM32G031C6T6

STM32G031C6T6 - 64MHz Cortex-M0+ 32KB MCU | STMicroelectronics

The STMicroelectronics STM32G031C6T6 is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 64 MHz, with 32 KB of Flash memory and 8 KB of SRAM, housed in a 48-LQFP 7 x 7 mm package. It belongs to the STM32G0 mainstream microcontroller family and targets compact embedded products requiring efficient control performance, low-power operation, and broad peripheral integration. A microcontroller is a programmable system-on-chip that combines a processor core, memory, interfaces, timers, and analog or communications peripherals on one semiconductor device. Within the product hierarchy, this STM32G0 device is a 32-bit microcontroller based on an Arm Cortex-M0+ processor. It provides a practical balance between processing capability, memory capacity, package size, and embedded-system complexity for compact control designs. Verified distributor information identifies a maximum operating frequency of 64 MHz, 32 KB of Flash, and 8 KB of SRAM. The device also provides two USART interfaces according to the Mouser product result. These resources support asynchronous serial communication, control-loop execution, state-machine logic, sensor acquisition, and general-purpose embedded processing while retaining a straightforward pin count and package format. The STM32G0 family is positioned for energy-efficient embedded control. Its Arm Cortex-M0+ architecture provides a compact instruction set and broad ecosystem support, while the 64 MHz operating point offers additional timing margin for GPIO, timers, serial interfaces, and application-specific peripherals. Firmware engineers can evaluate clock configuration, low-power modes, memory use, and peripheral pin mapping from the manufacturer datasheet before committing a PCB to this exact variant. Typical design uses include low-cost sensor nodes, industrial control modules, digital monitoring equipment, compact motor-control peripherals, communications modules, and embedded consumer products. The 48-LQFP package exposes more I/O than smaller packages and remains convenient for prototype boards and moderate-density control products. Board-level design must still verify every pin, alternate function, power requirement, decoupling arrangement, programming interface, and exposed-pin connection against the exact package pinout. The most important sourcing check is package and pin compatibility. An MCU with a similar core or memory size cannot automatically replace STM32G031C6T6; boot behavior, power pins, peripheral mapping, flash organization, SRAM, clock tree, and firmware support must match. For production replacement, compare the complete ordering code and validate with STMicroelectronics documentation rather than relying only on a distributor similarity search. This page combines verified manufacturer and distributor data with explicit data gaps, practical selection guidance, and source-backed commercial information. Because the supplied source snippets do not expose the full datasheet parameter tables, pricing, package drawings, or validated drop-in alternatives, it separates verified facts from information that must be confirmed before design release.

詢價 聯絡我們
STM32G031C6U6 - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics
STM32G031C6U6

STM32G031C6U6 - 64MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics

The STMicroelectronics STM32G031C6U6 is a 32-bit Arm Cortex-M0+ microcontroller operating up to 64 MHz, with 32 KB of Flash memory, 8 KB of SRAM, and a 48-pin UFQFPN package measuring 7 x 7 mm. It provides two USART peripherals, timers, an ADC, and communication interfaces for compact embedded-control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The STM32G031C6U6 belongs to the STM32G0 mainstream family, where the Cortex-M0+ core forms the foundation of the Arm Cortex-M product category. This hierarchy places it within 32-bit RISC microcontrollers designed for control-oriented systems that require deterministic peripheral access, efficient code execution, and a broad set of integrated I/O resources. Key device characteristics include a maximum operating frequency of 64 MHz, a 32 K x 8 Flash organization, and 8 KB of SRAM. Two USART channels support serial equipment and industrial communication, while the listed timers, ADC, and communication interfaces reduce the need for external peripheral ICs. The specified 1.7 V to 3.6 V operating range supports low-voltage embedded systems, although detailed current, temperature, and timing limits must be confirmed in the manufacturer datasheet. The STM32G031C6U6 combines an Arm Cortex-M0+ RISC processor with embedded Flash and SRAM, an internal digital-core supply, and integrated analog and serial peripherals. The manufacturer datasheet notes that packages without a dedicated VREF+ pin connect VREF+ internally with VDD and require the internal voltage-reference buffer to remain disabled. Its 48-pin package combines a compact 7 x 7 mm footprint with enough pins for embedded control, sensor acquisition, and serial communication. Typical applications include compact industrial controllers, sensor-interface modules, serial bridges, small motor-control systems, and low-power embedded instruments. Its two USART channels are useful for configuration consoles or external transceivers, while the ADC supports analog monitoring. The integrated communications and timer resources make the device suitable for designs where board area and external component count are important constraints. Designers should verify all 48 package pins, alternate-function assignments, clock configuration, decoupling requirements, and exposed-pad connection against the package pinout in the manufacturer datasheet. Firmware, boot configuration, and peripheral assignments must also be reviewed before production release because alternate functions and device options can constrain otherwise interchangeable connections. This page consolidates the verified manufacturer and distributor facts for STM32G031C6U6 and distinguishes documented characteristics from values that still require design review. It also compares same-package STM32G031 variants, summarizes procurement information as of 2026-10-30, and identifies the pinout and electrical details that engineers must confirm before treating a substitute as a drop-in replacement.

詢價 聯絡我們
STM32G031C8T6 - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics
STM32G031C8T6

STM32G031C8T6 - 64KB Flash ARM Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32G031C8T6 is a 32-bit ARM Cortex-M0+ based microcontroller from the STM32G0 series, offering a balanced combination of performance, power efficiency, and rich analog peripherals. It operates at a maximum frequency of 64 MHz and provides 64 KB of flash memory and 8 KB of SRAM, making it suitable for a wide range of cost-sensitive and space-constrained embedded applications. The device is housed in a 48-pin LQFP package (7x7 mm) with a 0.5 mm pitch, enabling compact PCB designs. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It integrates a processor core, memory (flash and SRAM), and programmable input/output peripherals on a single chip. Microcontrollers are the backbone of modern embedded systems, from simple household appliances to complex industrial automation. The STM32G031C8T6 belongs to the STM32G0 family, which is positioned as an entry-level, high-efficiency series within the broader STM32 portfolio, targeting applications that require low power consumption, robust analog capabilities, and a rich set of communication interfaces. Key features of the STM32G031C8T6 include a 12-bit ADC with hardware oversampling (up to 16-bit resolution), a 12-bit DAC, two comparators, and an operational amplifier. It also integrates multiple communication interfaces: I2C, SPI, USART, and a low-power UART. The device supports a wide supply voltage range from 2.0V to 3.6V and offers several low-power modes, including Sleep, Stop, and Standby, with a typical standby current of only 0.27 µA. The MCU is designed with a high level of integration, reducing the need for external components and simplifying system design. From a technical depth perspective, the STM32G031C8T6 is built on a 90 nm process technology, which contributes to its low power consumption and high performance. The Cortex-M0+ core includes a single-cycle multiplier and a nested vectored interrupt controller (NVIC), enabling efficient interrupt handling. The device also features a memory protection unit (MPU) for enhanced security and a cyclic redundancy check (CRC) unit for data integrity. The clock system is flexible, with an internal 16 MHz RC oscillator, an internal 32 kHz RC oscillator, and support for external crystals, allowing designers to optimize for cost or accuracy. Typical applications for the STM32G031C8T6 include consumer electronics, industrial control, home automation, and portable devices. Its rich analog peripherals make it ideal for sensor interfacing, motor control, and power management. The low-power modes and wide voltage range enable battery-powered applications such as wearables and IoT nodes. The device is also well-suited for simple human-machine interfaces (HMI) with its capacitive touch sensing capability. When designing with this MCU, it is essential to provide proper decoupling capacitors on the power supply pins and to follow the recommended layout guidelines in the datasheet to minimize noise and ensure reliable operation. The internal RC oscillators are sufficient for many applications, but for precise timing, an external crystal should be used. Additionally, the device's boot pins must be configured correctly to select the desired boot mode (flash, system memory, or SRAM).

詢價 聯絡我們
STM32G031C8T7 - 64MHz Cortex-M0+ MCU | STMicroelectronics
STM32G031C8T7

STM32G031C8T7 - 64MHz Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32G031C8T7 is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 64 MHz, with 64 KB of Flash memory and 8 KB of SRAM, housed in a 48-pin LQFP 7 x 7 mm package. The device is positioned for compact embedded-control systems that require efficient real-time processing, mixed-signal measurement, timer-driven control, and serial connectivity without the complexity of a higher-performance Cortex-M core. A microcontroller is a programmable semiconductor that integrates a processor core, memory, analog and digital peripherals, and communication interfaces onto one device. The STM32G0 family belongs to the broader embedded-controller hierarchy: Arm Cortex-M0+ core, 32-bit microcontroller, embedded processor, and system-on-chip. Its compact architecture is intended for cost-sensitive products in which deterministic control, low component count, and flexible peripheral integration matter more than high-end graphics or large memory capacity. The STM32G031C8T7 combines a 64 MHz Arm Cortex-M0+ processor with 64 KB of Flash and 8 KB of SRAM. The listed connectivity capabilities include I2C, SPI, UART, IrDA, LIN bus, and Smart Card interfaces. Forty-four I/O pins provide connections for sensors, actuators, displays, communications, and control signals. Operation from 2.5 V and 3.3 V supply rails also supports both conventional embedded-system voltages found in industrial, consumer, and instrumentation equipment. The STM32G031x4, STM32G031x6, and STM32G031x8 devices share the Arm Cortex-M0+ platform, while their memory capacities and peripheral resources differ by density grade. The x8 designation in STM32G031C8 corresponds to the 64 KB Flash variant shown in the product listing. The C package code identifies the 48-pin configuration, while the T7 ordering code identifies the specified temperature and package arrangement associated with this ordering code. Typical applications include low-cost sensor nodes, compact motor and timer-control boards, industrial monitoring instruments, communication modules, and mixed-signal control products. Designers can use the analog-to-digital conversion, timer, PWM, and serial interface resources to consolidate functions that otherwise require separate analog, timing, and communication components. The 48-pin LQFP also provides more I/O access than smaller packages while remaining inspectable and repairable by conventional leaded-assembly methods. Layout planning should prioritize short, continuous supply and ground paths around the microcontroller, especially around analog inputs and external interfaces. Decoupling capacitors should be placed directly beside their associated power pins, while oscillator and high-speed signal routes should avoid crossing noisy switching paths. Firmware changes between MCU families should be reviewed against peripheral availability, interrupt behavior, memory layout, and pin multiplexing before production use. This product record combines manufacturer device information, distributor specifications, package characteristics, replacement guidance, and practical design notes. It is intended to help engineers determine whether the STM32G031C8T7 matches the required core performance, memory capacity, I/O count, interface set, package, and operating environment before committing a design to production.

詢價 聯絡我們
STM32G031C8U6 - 64MHz 64KB Cortex-M0+ MCU | STMicroelectronics
STM32G031C8U6

STM32G031C8U6 - 64MHz 64KB Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32G031C8U6 is an Arm Cortex-M0+ 32-bit RISC microcontroller operating at up to 64 MHz, with 64 KB of Flash memory in a 48-UFQFPN 7 x 7 mm package. The device belongs to the STM32G0 mainstream microcontroller family and combines a compact 48-pin package with embedded control and general-purpose mixed-signal capabilities. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and interfaces into one package. The STM32G031C8U6 uses the Arm Cortex-M0+ core, an efficient 32-bit architecture intended for embedded control. Its 64 MHz operating frequency provides headroom for responsive control loops and connected embedded products while retaining a simple instruction set and low system complexity. Verified product information identifies the device as a 32-bit Cortex-M0+ MCU with 64 KB Flash and a 48-UFQFPN package. The STM32G031x4, STM32G031x6, and STM32G031x8 devices are described by STMicroelectronics as mainstream products based on the high-performance Arm Cortex-M0+ core. The supplied data does not specify RAM size, operating voltage, GPIO count, temperature range, or individual peripheral ratings; those values should be confirmed in the manufacturer datasheet before design release. Typical uses for this device class include compact industrial control modules, sensor interfaces, compact motor-control boards, communication equipment, and low-power embedded control products. The 48-pin package offers more I/O capability than smaller MCU packages, which can simplify board routing when a design needs multiple external signals. The 64 MHz core is also appropriate for applications that combine control logic with moderate protocol or data-processing work. For PCB design, the 7 x 7 mm UFQFPN footprint requires careful land-pattern and thermal-pad design. Use the manufacturer package drawing and pinout rather than inferring connections from the distributor description. Confirm exposed-pad treatment, power decoupling, oscillator connections, and programming access against the official STM32G031C8 documentation. This product page consolidates the verified manufacturer and distributor information, package details, procurement links, and engineering-oriented design guidance for STM32G031C8U6. It does not substitute for the complete electrical, timing, environmental, or pin-level specifications in the STMicroelectronics datasheet.

詢價 聯絡我們
STM32G031C8U6TR - 64MHz 64KB Cortex-M0+ MCU | STMicroelectronics (Tape & Reel)
STM32G031C8U6TR

STM32G031C8U6TR - 64MHz 64KB Cortex-M0+ MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32G031C8U6TR is an Arm Cortex-M0+ 32-bit RISC microcontroller operating at up to 64 MHz, with 64 KB of Flash memory in a 48-UFQFPN 7 x 7 mm package. The device belongs to the STM32G0 mainstream microcontroller family and combines a compact 48-pin package with embedded control and general-purpose mixed-signal capabilities. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and interfaces into one package. The STM32G031C8U6TR uses the Arm Cortex-M0+ core, an efficient 32-bit architecture intended for embedded control. Its 64 MHz operating frequency provides headroom for responsive control loops and connected embedded products while retaining a simple instruction set and low system complexity. Verified product information identifies the device as a 32-bit Cortex-M0+ MCU with 64 KB Flash and a 48-UFQFPN package. The STM32G031x4, STM32G031x6, and STM32G031x8 devices are described by STMicroelectronics as mainstream products based on the high-performance Arm Cortex-M0+ core. The supplied data does not specify RAM size, operating voltage, GPIO count, temperature range, or individual peripheral ratings; those values should be confirmed in the manufacturer datasheet before design release. Typical uses for this device class include compact industrial control modules, sensor interfaces, compact motor-control boards, communication equipment, and low-power embedded control products. The 48-pin package offers more I/O capability than smaller MCU packages, which can simplify board routing when a design needs multiple external signals. The 64 MHz core is also appropriate for applications that combine control logic with moderate protocol or data-processing work. For PCB design, the 7 x 7 mm UFQFPN footprint requires careful land-pattern and thermal-pad design. Use the manufacturer package drawing and pinout rather than inferring connections from the distributor description. Confirm exposed-pad treatment, power decoupling, oscillator connections, and programming access against the official STM32G031C8 documentation. This product page consolidates the verified manufacturer and distributor information, package details, procurement links, and engineering-oriented design guidance for STM32G031C8U6TR. It does not substitute for the complete electrical, timing, environmental, or pin-level specifications in the STMicroelectronics datasheet.

詢價 聯絡我們
STM32G031F4P3 - 64MHz Arm Cortex-M0+ MCU | STMicroelectronics
STM32G031F4P3

STM32G031F4P3 - 64MHz Arm Cortex-M0+ MCU | STMicroelectronics

STMicroelectronics STM32G031F4P3 is a 32-bit Arm Cortex-M0+ microcontroller rated up to 64 MHz, with 16 KB of Flash memory, 8 KB of SRAM, and a 20-pin TSSOP package. It operates from 1.7 V to 3.6 V and includes two USART interfaces, timers, an ADC, and communication interfaces for compact embedded-control designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The STM32G0 family belongs to the hierarchy of Arm Cortex-M0+ processor, 32-bit microcontroller, embedded processor, and semiconductor. STM32G031F4P3 targets cost-sensitive control systems where moderate processing speed, compact packaging, and a broad set of mixed-signal and serial peripherals are more important than large memory capacity. The device operates at up to 64 MHz and provides 16 KB of Flash memory plus 8 KB of SRAM. Its 1.7 V to 3.6 V operating range supports low-voltage embedded systems. Two USARTs permit serial communication with sensors, displays, wireless modules, or service interfaces, while the integrated timers and ADC support periodic control and analog-signal measurement. The 20-pin TSSOP package also facilitates compact, high-density PCB assembly. The Arm Cortex-M0+ architecture uses a 32-bit RISC instruction set designed for efficient embedded workloads. Its relatively compact instruction set and peripheral ecosystem make it suitable for motor-control assistance, simple communications, sensor hubs, and consumer-equipment controllers. Peripheral configuration and software development are supported by the STM32G0 family ecosystem, including STM32Cube programming tools and the ST-LINK debug and programming interface. Typical applications include compact sensor nodes, digital control panels, low-cost communication modules, industrial sensing terminals, and compact consumer appliances. A design can assign two USART channels to separate external devices, use timer outputs for periodic functions, and use the ADC for analog monitoring. Firmware should be configured around the available 16 KB of Flash and 8 KB of SRAM, avoiding resource-intensive buffering or libraries that exceed those limits. A key design consideration is decoupling and correct voltage selection. Place the required input and output capacitors close to the power pins, route sensitive analog and communication signals away from switching nodes, and confirm the external components connected to exposed pins meet the device's electrical limits. Software developers should also use the STM32CubeMX pin-assignment workflow so alternate-function and peripheral mappings match the selected TSSOP-20 footprint. This product page combines manufacturer specifications, package details, application guidance, drop-in alternatives, and practical design notes. It is intended to accelerate component selection, PCB planning, firmware setup, and sourcing for compact Cortex-M0+ control systems.

詢價 聯絡我們
STM32G031F4P6 - 64MHz Cortex-M0+ 16KB MCU | STMicroelectronics
STM32G031F4P6

STM32G031F4P6 - 64MHz Cortex-M0+ 16KB MCU | STMicroelectronics

STMicroelectronics STM32G031F4P6 is an ARM Cortex-M0+ 32-bit microcontroller with a 64 MHz maximum CPU frequency, 16 KB of Flash memory, 8 KB of RAM, and a 20-TSSOP package. The device belongs to the STM32G0 series and targets compact embedded systems requiring efficient general-purpose control, low power consumption, and a small package footprint. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, volatile data memory, and peripherals on one device. Within the product hierarchy, the STM32G031F4P6 is an ARM Cortex-M0+ MCU, an STM32G0-series microcontroller, and a 32-bit embedded-control semiconductor. Its combination of 64 MHz processing, 16 KB Flash, and 8 KB RAM is suitable for small control systems, embedded accessories, instrumentation, and compact consumer products. Verified distributor information identifies the part as a 3 V, 20-TSSOP device with 16 KB Flash and 8 KB RAM. The 20-pin TSSOP format supports compact PCB layouts while retaining accessible peripheral connections. The exact pin names, voltage limits, peripheral inventory, current ratings, and environmental limits were not included in the supplied source snippets and therefore require confirmation from the manufacturer datasheet before a new design is released. The Cortex-M0+ architecture provides a 32-bit processing environment with an emphasis on efficient embedded control. A 64 MHz clock gives the processor more timing headroom for input sampling, state-machine logic, communication tasks, and control-loop updates than lower-frequency microcontrollers. Memory use is the main design constraint: 16 KB Flash must hold the bootloader, application code, and constant data, while 8 KB RAM must support stack depth, working variables, buffers, and peripheral data. Typical uses include small motor and relay controllers, sensor-hub nodes, compact industrial modules, communication-assisted accessories, and low-cost embedded products where a full STM32G0 system is unnecessary. Designers should include external flash only if the application exceeds the internal memory budget. Software migration decisions should also account for peripheral differences between STM32G0 variants, even when several parts share the same package. Before layout or firmware release, verify the exact pin assignment, alternate-function mapping, decoupling requirements, operating-voltage limits, exposed programming/test pins, and absolute maximum ratings in the manufacturer datasheet. The supplied records confirm the core identity, memory configuration, clock, package, and a verified LCSC unit price of $0.6593 as of 2026-10-30, but they do not provide complete electrical or pinout tables. This page combines verified distributor specifications, sourced replacement candidates, procurement data, and practical memory-budget guidance. It also identifies where manufacturer-level verification is mandatory, preventing incomplete distributor snippets from being mistaken for complete production specifications.

詢價 聯絡我們
STM32G031F6P6 - 64MHz Cortex-M0+ MCU, 32KB Flash | ST
STM32G031F6P6

STM32G031F6P6 - 64MHz Cortex-M0+ MCU, 32KB Flash | ST

The STMicroelectronics STM32G031F6P6 is a mainstream 32-bit Arm Cortex-M0+ microcontroller operating up to 64 MHz, with 32 KB of Flash memory, 8 KB of RAM, and a 20-pin TSSOP package. The device supports a 1.7 V to 3.6 V operating-voltage range and combines two USART interfaces with timers and an ADC for compact embedded-control designs. A microcontroller is an integrated semiconductor that executes firmware, reads inputs, controls outputs, and manages system timing. The STM32G031F6P6 belongs to the STM32G0 mainstream MCU family and uses the Arm Cortex-M0+ processor, a 32-bit RISC architecture designed for efficient control-oriented workloads. Its combination of modest memory, fast execution, and multiple communication peripherals makes it suitable for cost-sensitive embedded products. Verified distributor information identifies the device as a 64 MHz STM32G0 MCU with 32 KB Flash, 8 KB RAM, two USARTs, timers, an ADC, and communication interfaces. The 20-TSSOP package provides 20 pins and is supplied in tube packaging according to the Arrow listing. The verified operating-temperature range is -40 °C to +85 °C, and RoHS compliance is reported by FindMyChip. The Cortex-M0+ core provides a practical balance between processing capability and resource consumption for embedded control. With two USARTs, designers can support serial consoles, sensors, modules, or industrial peripherals while retaining timers for periodic control tasks. The ADC enables analog measurements, and the communication interfaces expand the range of connected equipment supported by a single controller. Typical uses include industrial control modules, compact sensor nodes, building-automation controllers, small motor-control products, and low-cost consumer devices. The 20-pin TSSOP package is useful when a small, readily available through-hole-compatible package is preferred, although the exact pin functions and exposed electrical requirements must be checked against the STMicroelectronics datasheet before layout. When designing around the STM32G031F6P6, confirm supply-voltage tolerances, peripheral pin multiplexing, clock configuration, decoupling, programming method, and exposed-pin requirements. The verified data does not provide detailed pin names or pricing tiers for every quantity, so those values should be checked against the manufacturer datasheet and current distributor quotations before release.

詢價 聯絡我們
STM32G031F8P3 - 64MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32G031F8P3

STM32G031F8P3 - 64MHz Cortex-M0+ 64KB MCU | STMicroelectronics

The STMicroelectronics STM32G031F8P3 is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 64 MHz, with 64 KB of Flash memory and 8 KB of SRAM in a 20-pin TSSOP package. It belongs to the STM32G0 mainstream microcontroller family and is designed for cost-sensitive embedded control applications requiring compact packaging, efficient processing, and a broad set of mixed-signal peripherals. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals such as timers, communication interfaces, analog converters, and GPIO into one package. The STM32G0 product hierarchy places this device among Arm Cortex-M0+ embedded processors, where the reduced instruction set, low power behavior, and compact package support cost-sensitive control systems, sensors, consumer accessories, industrial equipment, and connected products. The STM32G031F8P3 combines a 64 MHz Cortex-M0+ core with 64 KB of Flash and 8 KB of SRAM. Its 32-bit architecture provides efficient execution of control routines, communication handlers, and peripheral servicing while requiring a relatively small embedded code footprint. Hardware Flash protection and a securable area are listed among the memory features, helping isolate critical firmware and supporting product-security designs. Operating-temperature options listed for the STM32G031F8 family include -40°C to 85°C, -40°C to 105°C, and -40°C to 125°C. The device integrates a 12-bit Analog-to-Digital Converter, high-resolution timers, communication interfaces, and GPIO into a 20-TSSOP footprint. These resources support designs that need to measure analog inputs, generate precise timing signals, operate control loops, and communicate with sensors or external controllers. Its 64 MHz maximum clock frequency provides additional timing margin for multitasking, protocol handling, and real-time control without requiring a higher-performance Cortex-M core. Typical applications include compact motor controllers, building and industrial automation modules, low-cost sensor nodes, appliance control boards, battery-powered instruments, and USB Type-C accessories. The small 20-pin TSSOP package simplifies board assembly, while the combination of SRAM, Flash, analog conversion, timers, and serial interfaces supports consolidation of multiple discrete functions into a single embedded controller. Designers should select decoupling capacitors from the manufacturer reference schematic, verify every alternate-function pin against the device datasheet, and confirm the programming and debug interface arrangement before layout release. Because the 20-pin package exposes a limited number of GPIO and power pins, pin multiplexing should be planned early enough to prevent conflicts among communications, timers, analog inputs, and debug functions. This product page combines manufacturer specifications, package information, replacement guidance, and practical design considerations to help engineers evaluate the STM32G031F8P3 for embedded-control designs.

詢價 聯絡我們
STM32G031F8P3TR - 64MHz Cortex-M0+ 64KB Flash | STMicroelectronics
STM32G031F8P3TR

STM32G031F8P3TR - 64MHz Cortex-M0+ 64KB Flash | STMicroelectronics

The STMicroelectronics STM32G031F8P3TR is a 32-bit ARM Cortex-M0+ microcontroller rated up to 64 MHz, with 64 KB of Flash memory and 8 KB of SRAM, packaged in a 20-pin TSSOP. It belongs to the STM32G0 mainstream microcontroller family and is designed for compact, cost-sensitive embedded control designs. The device combines a 2.5 V to 3.3 V operating supply with integrated microcontroller peripherals for communication, timing, and analog signal acquisition. According to the STMicroelectronics STM32G031F8 product page, the STM32G031x4/x6/x8 devices use a high-performance Arm Cortex-M0+ 32-bit RISC core operating at up to 64 MHz. The STM32G031F8P3TR ordering code identifies the 64 KB Flash configuration in a 20-TSSOP package, making it a practical choice for compact controllers, motor-control systems, USB-connected products, industrial modules, and consumer electronics. Its small TSSOP footprint supports assembly on constrained boards while retaining a conventional MCU programming and debugging workflow. The STM32G0 series is suited to applications that need deterministic embedded processing without the cost or complexity of higher-performance Cortex-M cores. The 64 MHz operating rate supports responsive control loops, protocol handling, and general user-interface logic. The 64 KB Flash area provides room for firmware, boot code, configuration data, and application routines, while the 8 KB SRAM supports working memory and peripheral buffering. The manufacturer product page identifies the STM32G031x4/x6/x8 as mainstream devices based on the Cortex-M0+ architecture; designers should consult the manufacturer datasheet for the exact peripheral map, clock tree, electrical limits, pin multiplexing, and programming details before finalizing a board design. The 20-pin TSSOP package is especially useful for compact OEM controller boards where component height, assembly cost, and PCB area matter. STM32G031F8P3TR can serve as the central controller in a compact industrial sensing module, a small motor controller, a USB peripheral, or a consumer sub-system. Its combination of 64 MHz processing, 64 KB Flash, and 8 KB SRAM balances performance and resource consumption for embedded products that do not require external memory. The device is identified by STMicroelectronics as an STM32G0 mainstream MCU, and the product family is intended for embedded systems requiring low power, compact packaging, and broad peripheral integration. This product page combines the manufacturer product description, distributor package and memory details, replacement guidance, and practical design considerations to support component selection, PCB planning, firmware development, and sourcing decisions.

詢價 聯絡我們
STM32G031F8P6 - 64MHz Cortex-M0+ MCU, 64KB Flash | STMicroelectronics
STM32G031F8P6

STM32G031F8P6 - 64MHz Cortex-M0+ MCU, 64KB Flash | STMicroelectronics

The STMicroelectronics STM32G031F8P6 is a mainstream Arm Cortex-M0+ 32-bit microcontroller operating at up to 64 MHz with 64 KB Flash and 8 KB SRAM in a 20-pin TSSOP package. It belongs to the STM32G0 family, ST's cost-optimized successor to the STM32F0 line, targeting LIN-connected control nodes, low-end motor control, and compact sensor-hub designs. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals into one package. The Cortex-M0+ is Arm's smallest and most energy-efficient 32-bit core, sitting in the hierarchy: Cortex-M0+ -> Arm Cortex-M -> 32-bit RISC processor -> MCU -> semiconductor. The STM32G0 family further integrates a 5V-tolerant I/O architecture and a 12-bit ADC, simplifying designs that must interface with 5V legacy sensors. Key features of the STM32G031F8P6 include 64 MHz maximum CPU frequency, 64 KB of embedded Flash with ECC, 8 KB SRAM, a 12-bit 2.5 MSPS ADC, two USART interfaces supporting LIN and IrDA, a 16-bit advanced-control timer, multiple general-purpose 16-bit timers, an I2C, an SPI, and a USB 2.0 Full-speed device controller (Type-C power-delivery capable on related parts). The 20-pin TSSOP package exposes 18 GPIO with 5V tolerance, making it suitable for mixed-voltage designs. The architecture uses a single AHB/APB bus matrix with a Cortex-M0+ core featuring single-cycle I/O access, an MPU for memory protection, and a built-in vectored interrupt controller (NVIC). The on-chip 12-bit ADC achieves 2.5 MSPS with hardware oversampling, and the comparators and op-amps available in larger variants are omitted here to fit the 20-pin footprint. Typical applications include LIN slave nodes in automotive body electronics, low-end motor-control loops (BLDC and stepper), consumer appliances (washing machines, induction cooktops), small home appliances, smart sensors, USB Type-C cable markers, and low-cost IoT end nodes. The USB FS device controller enables low-cost cable-mark and HID designs. When designing with this MCU, ensure the VDDA pin is properly decoupled (100 nF + 1 uF) and that NRST has a 10 kohm pull-up and 100 nF cap if not driven externally. The 20-pin TSSOP package has limited GPIO (18) - plan pin allocation carefully for multi-peripheral designs and consider the LQFP-32 variant if more I/O is required.

USD $1.07 有庫存
STM32G031G4U6 - 64MHz Cortex-M0+ MCU | STMicroelectronics
STM32G031G4U6

STM32G031G4U6 - 64MHz Cortex-M0+ MCU | STMicroelectronics

STMicroelectronics STM32G031G4U6 is an Arm Cortex-M0+ 32-bit RISC microcontroller operating at up to 64 MHz, with 16 KB of Flash memory and 8 KB of SRAM in a 28-pin UFQFPN package measuring 4 x 4 mm. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into a single device. The STM32G0 family belongs to the embedded-processing hierarchy that includes 32-bit RISC cores, microcontrollers, embedded systems, and semiconductor components. Its combination of compact packaging, serial communication interfaces, analog conversion resources, and timers makes it suitable for cost-sensitive embedded control designs. The STM32G031G4U6 provides 16 KB of Flash for program storage, 8 KB of SRAM for working data, and a maximum CPU frequency of 64 MHz. It supports two USART peripherals, an ADC, timers, and communication interfaces. Its stated operating voltage range is 1.7 V to 3.6 V, allowing operation from low-voltage 3.3 V systems when appropriate regulator headroom is maintained. The 28-UFQFPN package occupies only 4 x 4 mm, making the device appropriate for compact control boards, sensor nodes, and embedded products where board area is limited. Its Arm Cortex-M0+ architecture supports efficient 32-bit processing while retaining a simple embedded-control design profile. Exact peripheral counts, timer resources, pin assignments, and conversion performance should be confirmed in the manufacturer pin description and electrical characteristics tables before design release. Typical applications include low-power sensor interfaces, small industrial control modules, building accessory controllers, compact motor-control supervisory systems, and communication-equipped IoT endpoints. Two USART channels are particularly useful when a product needs concurrent serial links for a host controller, local module, diagnostics, or an external radio. The principal design consideration is careful 1.7 V to 3.6 V power-supply planning. Decoupling must follow the manufacturer reference layout, unused inputs must be configured correctly, and firmware should validate actual clock, ADC, and communications behavior on production hardware rather than relying solely on nominal family-level specifications. This page combines the official product positioning with package, memory, voltage, interface, and temperature information, then adds application guidance, parameter comparisons, and practical implementation notes for faster engineering evaluation.

詢價 聯絡我們