產品(46,000+)

MAX14805ECM+ - 16-Channel High-Voltage Switch | Maxim
MAX14805ECM+

MAX14805ECM+ - 16-Channel High-Voltage Switch | Maxim

The Maxim Integrated MAX14805ECM+ is a 16-channel, high-voltage analog switch IC with an 8:1, two-channel switch arrangement, supplied in a 48-LQFP 7 x 7 mm package. It uses two independent logic controls, DIN1 and DIN2, to operate two banks of eight SPST analog switches: DIN1 controls switch 0 through switch 7, while DIN2 controls switch 8 through switch 15. This architecture makes the device suitable for systems requiring numerous independently controlled high-voltage signal paths. An analog switch is an integrated semiconductor that routes an electrical signal between circuit nodes under digital control. In this product category, the MAX14805ECM+ belongs to the analog switch and switch matrix hierarchy, where multiple SPST switches are combined into a controlled routing network. Digital controls can place each switch into a conducting or nonconducting state, allowing one controller to manage external transducers, test points, or voltage domains without relying on separate mechanical relays. The verified product information identifies the MAX14805 as a high-voltage analog switch and confirms its 16-channel architecture. The two-bank organization is important because each eight-switch bank has a dedicated control input. MAX14805ECM+ is identified specifically as a 48-LQFP 7 x 7 mm device, while the related MAX14806 option adds 40 kΩ bleed resistors on every switch terminal. The MAX14805ECM+ is the appropriate selection when independent high-voltage switching is required without the MAX14806 bleed-resistor feature. The MAX14805 and MAX14806 family uses SPST switches rather than SPDT, DPDT, or multiplexer structures. This simplifies control logic but means that each switch provides only a connection path rather than selecting one of two destinations. System designers must therefore account for the off-state behavior, signal polarity, switch resistance, leakage, and control timing during PCB and firmware design. The related family is specified for an extended -40°C to +85°C temperature range according to the supplied datasheet information. Primary applications include ultrasound imaging systems, where multiple transducer-element connections must be switched during transmit and receive phases. The same 16-channel structure can also support industrial test systems, high-voltage instrumentation, medical signal-routing equipment, and multichannel measurement setups. In each case, the useful feature is coordinated control of many physical switching paths from two compact digital inputs. A critical design consideration is high-voltage layout safety. High-voltage traces must maintain the required clearance and creepage distances, while exposed package pads and test structures require appropriate insulation and guarding. Decoupling, control-logic levels, and the electrical limits of connected nodes must also be checked against the manufacturer datasheet before implementation. This product page consolidates verified distributor availability, package information, family architecture, and cross-reference findings into an engineering-oriented guide. It also separates confirmed facts from parameters that still require verification in the manufacturer datasheet, helping engineers evaluate the MAX14805ECM+ without confusing it with the resistor-equipped MAX14806 variant.

詢價 聯絡我們
MAX14806CCM+ 16-Channel High-Voltage Analog Switch
MAX14806CCM+

MAX14806CCM+ 16-Channel High-Voltage Analog Switch

The Analog Devices MAX14806CCM+ is a 16-channel high-voltage analog switch IC organized as two banks of eight SPST channels, housed in a 48-LQFP (7x7 mm) package. The device uses Maxim's 200V process technology for high-voltage switching and is controlled through a digital interface. The MAX14806CCM+ is designed for ultrasound imaging systems where receive-bank selection, probe multiplexing, and relay-equivalent signal routing are required. A high-voltage analog switch is a semiconductor device that routes analog signals under digital control while supporting voltage levels and isolation requirements that exceed ordinary low-voltage signal switches. In the signal-chain hierarchy, the MAX14806CCM+ is an interface IC and analog switch, with application-level roles in ultrasound probe selection, bank switching, and high-voltage signal isolation. The verified product information identifies sixteen high-voltage, low-charge-injection SPST switches, two independently controlled banks of eight channels, a digital control interface, and operation from -40°C to +85°C. These features make the device suitable for biplane and triplane ultrasonic probe arrangements, where multiple echo paths must be selected without changing the surrounding PCB layout. The low-charge-injection characteristic is particularly relevant when preserving small received ultrasound signals. The MAX14806CCM+ uses a 200V process technology, while the exact supported signal-voltage limits, on-resistance across all operating conditions, channel leakage, control-logic levels, and timing values require confirmation from the manufacturer datasheet. The package is identified by distributors as a 48-LQFP (7x7 mm), while the manufacturer describes the device as a 48-pin TQFP package. The same-source cross-reference states that the MAX14806CCM+ is a drop-in replacement for the Supertex HV2731. For ultrasound probe-bank selection, the device can replace mechanical or relay-based routing when the system requires digital control and low-charge-injection switching. In biplane imaging, two banks of eight channels can support the two probe banks. For triplane imaging, the switch can be integrated into a multiplexed receive architecture, subject to the detailed system timing and signal-integrity requirements. When designing the PCB, reserve the exact 48-pin LQFP footprint and route control signals away from sensitive analog inputs. Confirm the absolute maximum signal voltage, supply requirements, input capacitance, charge injection, off isolation, and power dissipation in the manufacturer datasheet before committing the design. This page combines verified manufacturer and distributor information, drop-in cross-reference data, application guidance, and explicit markers for parameters that were not supplied in the source data.

詢價 聯絡我們
MAX14806CCM+T - 16-Channel 200V Ultrasound Switch | Analog Devices
MAX14806CCM+T

MAX14806CCM+T - 16-Channel 200V Ultrasound Switch | Analog Devices

Analog Devices MAX14806CCM+T is a 16-channel high-voltage analog switch IC built for ultrasound imaging and piezoelectric probe circuits. It provides two independently controlled banks of eight SPST switches, uses 200 V process technology, and includes integrated 40 kΩ bleed resistors on each switch terminal. The device is packaged in a 48-LQFP measuring 7 mm by 7 mm and operates from a 2.7 V to 5.5 V logic supply. A high-voltage analog switch is an integrated semiconductor device that routes high-voltage analog signals while isolating sensitive receiver or transmitter circuits when a channel is not selected. Within the signal-chain hierarchy, the MAX14806 belongs to the analog switch family, interface IC category, and broader semiconductor category. Its primary role in an ultrasound probe is selecting groups of piezoelectric elements without introducing excessive charge injection or allowing residual voltage to accumulate. The MAX14806CCM+T offers 16 SPST channels arranged as two banks of eight. Each terminal includes a 40 kΩ bleed resistor that helps reduce voltage buildup in capacitive loads such as piezoelectric elements. Digital controls DIN1 and DIN2 select the two eight-channel banks, while the 200 V switch process supports high-voltage analog signal routing. The specified extended operating range of -40°C to +85°C suits industrial and medical imaging equipment with controlled ambient conditions. Internally, the switch architecture uses separate high-voltage channels with integrated discharge paths. The bleed resistors provide a defined leakage route after deselection, which is particularly valuable when connecting capacitive transducers that can otherwise retain charge between transmit and receive cycles. Because switched nodes can develop substantial voltage, PCB creepage, clearance, exposed-pad treatment, and high-voltage routing require careful implementation. Typical uses include bank selection in biplane and triplane ultrasound probes, replacement of discrete high-voltage relays, and switching networks for piezoelectric imaging arrays. The 48-terminal surface-mount package supports compact probe electronics, while the integrated bleed resistors reduce the external component count needed for charge management. Designers should verify that every high-voltage trace has adequate spacing, avoid placing sensitive receiver paths beneath or beside switched nodes, and use the manufacturer pin-description table when assigning PCB connections. The digital interface operates from 2.7 V to 5.5 V, but control signals must not be treated as high-voltage lines because the 200 V rating applies to the switched analog nodes. This product page consolidates the device architecture, verified electrical attributes, package information, application guidance, and the documented Supertex HV2731 drop-in relationship into an engineering-oriented reference for ultrasound probe and high-voltage switching designs.

詢價 聯絡我們
MAX14807ECB+T - Dual 2.2A 220Vpp Analog Pulser | Analog Devices
MAX14807ECB+T

MAX14807ECB+T - Dual 2.2A 220Vpp Analog Pulser | Analog Devices

The Analog Devices MAX14807ECB+T is a dual, high-voltage analog pulser with 2.2A output current and waveform capability up to 220Vpp. The integrated circuit combines a differential amplifier, a Class AB push-pull output stage, and an active clamp for driving piezoelectric transducers in ultrasound systems without an external transformer. It operates in analog and digital modes, giving designers a single high-voltage driver for generated waveforms and controlled pulses. A high-voltage analog pulser is an integrated signal-conditioning and power-driver circuit that converts low-voltage commands or differential analog signals into substantially larger voltage and current levels. This device sits between a low-voltage signal source and a piezoelectric transducer, combining amplifier, gain selection, output-stage drive, active clamping, and protection functions in one package. That integration reduces the number of external high-voltage signal-chain stages required in an ultrasound transmitter. The MAX14807 features gain selection between 28dB and 40dB for its differential input amplifier. Analog mode uses this gain-selectable amplifier and Class AB push-pull output stage to produce high-voltage arbitrary waveforms. Digital mode provides direct high-voltage pulse generation, while the external bias resistor establishes the output-stage bias current. According to the manufacturer datasheet, the active clamp presents a 25Ω low-impedance path to ground, helping discharge the transducer output and return the circuit to a defined state between pulses. The device supports waveforms or pulses up to 220Vpp and provides output current of 2.2A. These ratings make it relevant to ultrasound imaging, industrial acoustic testing, nondestructive evaluation, piezoelectric positioning, and laboratory waveform systems. Because the output stage is intended to drive a capacitive transducer, pulse duration, repetition rate, duty cycle, transducer capacitance, and output dissipation should be evaluated together rather than independently. A key design consideration is that a 220Vpp capability does not eliminate the need for careful board-level insulation, creepage, clearance, and high-voltage layout practices. Keep high-voltage copper away from low-level inputs and external programming interfaces. Follow the manufacturer datasheet for bypass capacitors, bias-resistor selection, transducer connections, exposed-pad layout, and thermal constraints. This product page consolidates the manufacturer's operating modes and electrical highlights with application guidance, engineering design notes, lifecycle information, and an authenticity-controlled comparison of available drop-in alternatives. It is intended to help engineers evaluate whether the MAX14807ECB+T matches a high-voltage pulser requirement before committing a PCB layout.

詢價 聯絡我們
MAX1480ACPI+ - Isolated 250kbps RS-485/422 | Maxim
MAX1480ACPI+

MAX1480ACPI+ - Isolated 250kbps RS-485/422 | Maxim

The Maxim Integrated MAX1480ACPI+ is a complete, electrically isolated RS-485/RS-422 data-communications transceiver with a 5 V supply and a maximum data rate of 250 kb/s. It is packaged in a 28-pin DIP and provides one-half transceiver operation for systems that require isolated differential data communication. An RS-485/RS-422 interface transceiver is an interface IC that converts logic-level signals into differential bus signals and receives those differential signals back into logic levels. The MAX1480ACPI+ belongs to the broader isolated interface IC and data-transceiver hierarchy, where electrical isolation separates the logic side from the communications bus. That isolation is useful when the transceiver must withstand ground-potential differences, reduce common-mode coupling, or protect sensitive equipment connected to a noisy industrial bus. Key features include complete electrically isolated RS-485/RS-422 interfacing, half-duplex operation, a 5 V operating supply, and a 250 kb/s data rate. The MAX1480A family is available in a 28-pin DIP package, making it appropriate for industrial-control, test-equipment, building-control, and isolated network-interface designs where through-hole construction and galvanic separation are important. The device integrates the driver, receiver, isolation barrier, and associated interface functions into a hybrid microcircuit. A single 5 V supply on the logic side powers both sides of the interface according to the manufacturer description. This integrated approach reduces the number of external isolation components and simplifies the physical implementation of an isolated serial-data port. Typical uses include automated test equipment, HVAC and building-control networks, industrial-control links, local-area networks, and EMI-sensitive isolated RS-485 or RS-422 interfaces. The 28-pin DIP format is useful where a leaded package is preferred for manual assembly, repair, or compatibility with an existing through-hole board. Designers should verify the complete pinout, isolation ratings, bus loading, termination, and transient protection against the manufacturer datasheet before laying out a new PCB. Because this is a through-hole DIP device, connector creepage, isolation-barrier placement, and cable-side surge protection require particular attention. This page combines verified distributor information, manufacturer-family details, same-package alternatives, comparison parameters, and practical design guidance to support component selection beyond a basic distributor listing.

詢價 聯絡我們
MAX1480AEPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices
MAX1480AEPI+

MAX1480AEPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX1480AEPI+ is a complete electrically isolated RS-485/RS-422 data-communications transceiver with one half-duplex driver and one receiver, supplied in a 28-pin PDIP package. The device supports RS-485 and RS-422 interfaces, provides a data rate of 250 kbps as identified by the supplied distributor record, and operates from a single +5 V supply on the logic side. Its isolated bus-side outputs are designed for data interfaces operating in electrically noisy industrial environments. An isolated RS-485/RS-422 transceiver is an interface IC that transfers digital data between a logic system and a differential, multipoint or point-to-point communications bus. The transceiver hierarchy places this device within bus line transceivers, then interface ICs, semiconductors, and broader data-communication electronics. Galvanic isolation places a protective boundary between the logic-side circuitry and the external bus, helping limit fault-current and common-mode coupling into the host system. The MAX1480AEPI+ combines the RS-485/RS-422 driver and receiver in one isolated 28-pin PDIP device. The verified distributor description identifies a one-transmitter, one-receiver, half-duplex configuration and a 250 kbps data rate. The 28-pin PDIP package also provides generous pin spacing compared with a surface-mount package, which can simplify prototype assembly, inspection, and rework. The manufacturer lists ATE, HVAC and building-control networks, industrial control, local-area networks, and isolated EMI-sensitive interfaces among its applications. The half-duplex architecture allows the same bus driver to transmit and receive data at different times. Bus direction must therefore be managed by the host controller, while the transceiver handles conversion between the host's digital signals and the differential RS-485 or RS-422 bus. The isolated output structure is particularly relevant when the bus may experience ground-potential differences or where designers need to reduce the energy transferred from a bus fault into the local electronics. Typical uses include industrial-control nodes, building automation equipment, automated test equipment, local-area networks, and isolated data links exposed to electromagnetic interference. The MAX1480AEPI+ is most appropriate when an external RS-485 or RS-422 bus, a 250 kbps-class data rate, and galvanic isolation are required in the same through-hole package. It is not a substitute for an RS-232-only transceiver, and its isolation should not be treated as a substitute for surge protection on an unprotected external cable. The primary design consideration is the bus interface. The transceiver must be paired with correct termination, biasing, protection, and grounding practices for the selected RS-485 or RS-422 topology. Because the supplied data does not include complete electrical tables or a verified pin map, engineers should consult the official MAX1480A datasheet for pin names, isolation ratings, supply-current details, driver limits, and recommended external networks before releasing a production design. This page combines verified manufacturer and distributor information, same-family drop-in candidates, a parameter comparison, and practical design cautions. It also distinguishes verified facts from parameters that remain to be confirmed from the manufacturer datasheet, making the MAX1480AEPI+ easier to evaluate for industrial and EMI-sensitive interface designs.

詢價 聯絡我們
MAX1480BCPI+ - Isolated RS-485/RS-422 Transceiver, 28-PDIP | Analog Devices
MAX1480BCPI+

MAX1480BCPI+ - Isolated RS-485/RS-422 Transceiver, 28-PDIP | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX1480BCPI+ is a complete, electrically isolated RS-485/RS-422 data-communications interface IC housed in a 28-pin PDIP wide-body package. It integrates a half-duplex 1/1 transceiver with on-chip transformer-based galvanic isolation, allowing a single +5V supply on the logic side to power both sides of the interface while eliminating the need for an external DC/DC isolation supply. An RS-485/RS-422 transceiver is a differential line driver/receiver IC that converts a single-ended TTL/CMOS UART signal into a balanced differential signal transmitted over a twisted pair, providing high noise immunity and multi-drop capability over distances up to 1200 meters. The MAX1480BCPI+ belongs to the interface IC product hierarchy (interface IC > transceiver > RS-485/RS-422 transceiver > isolated transceiver) within Analog Devices' communication interface portfolio. Key features include 250 kbps maximum data rate with reduced-slew-rate drivers that minimize EMI and reflections on unterminated or improperly terminated buses, 70 mV receiver hysteresis for noise rejection on slow edges, and 1/1 driver/receiver count configured for half-duplex operation. The device operates from a single 5V supply, supports up to 32 transceivers on the bus, and meets all RS-485/RS-422 electrical specifications through its isolated outputs. The MAX1480BCPI+ uses a hybrid microcircuit construction combining CMOS logic with pulse transformers to deliver 1000 Vrms (per datasheet) of galvanic isolation between the logic and bus sides, eliminating ground loops and protecting sensitive logic from bus-side faults. This integrated approach removes the need for designers to qualify discrete optocouplers and isolated DC/DC converters, reducing BOM count and PCB area. Typical applications include industrial fieldbus networks (Modbus, PROFIBUS), isolated point-to-point data links between PLCs and motor drives, building automation HVAC controllers, and any system requiring robust, isolated RS-485 communication across a high-voltage barrier. The wide-body 28-PDIP footprint is designed for through-hole assembly in industrial environments. When designing with this part, observe proper PCB layout for isolation barrier creepage and clearance, and note that the bus-side supply is internally derived - only the logic-side +5V needs to be provided externally. The MAX1480BCPI+ is the slower, lower-EMI variant compared to the MAX1480A; choose the MAX1480C variant for higher data rates when EMI is managed externally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
MAX1480BEPI+ - 250kbps Isolated RS-485/RS-422 | Maxim
MAX1480BEPI+

MAX1480BEPI+ - 250kbps Isolated RS-485/RS-422 | Maxim

The Maxim Integrated MAX1480BEPI+ is a complete electrically isolated RS-485/RS-422 transceiver with one driver and one receiver, a 250 kb/s data rate, and a 28-pin PDIP package. It is designed for half-duplex industrial data links where galvanic isolation and controlled-edge driver performance are required. The MAX1480B reduced-slew-rate driver is intended to minimize EMI and reduce reflections on longer or noisier bus interconnects. An isolated RS-485/RS-422 transceiver is an interface IC that combines differential bus-driver and receiver functions with an isolation barrier between the logic side and cable side. This class of transceiver belongs to the broader hierarchy of RS-485 transceivers, wired interface ICs, communication interfaces, and semiconductors. The MAX1480 family provides a practical way to connect a digital controller to a long, potentially noisy industrial bus without allowing ground currents or fault energy to cross the isolation boundary. Verified product information identifies the MAX1480BEPI+ as a 1/1 half-duplex RS-422/RS-485 transceiver in a 28-pin PDIP package. The manufacturer describes the isolated outputs as meeting RS-485 and RS-422 specifications. Search results also identify the MAX1480B reduced-slew-rate driver, a 250 kb/s data rate, and a 70 mV receiver hysteresis. The hybrid-microcircuit implementation provides integrated isolation rather than requiring separate optocouplers and isolated transceiver packages on the PCB. Typical uses include automated test equipment, HVAC and building-control networks, industrial-control links, local-area networks, and isolated RS-485/RS-422 data interfaces. The 250 kb/s rate makes the device suitable for low- and moderate-speed supervisory or control communications rather than high-rate storage networking. Half-duplex operation means that transmit and receive directions share the same differential pair, so the bus driver must be disabled while receiving. The principal design consideration is bus implementation. Differential pair routing should use a controlled-impedance, symmetrical layout where practical, with grounding and shielding selected according to the cable environment and installation requirements. Isolation is valuable, but it does not replace correct termination, common-mode protection, or surge suppression. The MAX1480BEPI+ should be selected only when its exact electrical ratings, isolation behavior, and pinout are verified against the manufacturer datasheet for the final design. This product page combines the verified manufacturer description, distributor listings, package identity, application context, and available comparison data for MAX1480 family variants. It also distinguishes exact family options from options whose electrical differences require engineering review before substitution.

詢價 聯絡我們
MAX1480CCPI+ - 250kbps Isolated RS-485/422 | Maxim Integrated
MAX1480CCPI+

MAX1480CCPI+ - 250kbps Isolated RS-485/422 | Maxim Integrated

The Maxim Integrated MAX1480CCPI+ is a complete electrically isolated RS-485/RS-422 data-interface transceiver with a 250 kbps maximum data rate, a 4.5 V to 5.5 V supply range, and a 28-pin DIP package. It combines one driver and one receiver in a half-duplex interface, providing a single-side logic supply while galvanic isolation separates the bus side from sensitive equipment. The device is designed for industrial-control networks, building-control systems, automated test equipment, and EMI-sensitive isolated data links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals. The MAX1480 belongs to the broader isolated interface-IC hierarchy, where isolation provides a galvanic barrier between a communication bus and the controlling electronics. This helps protect systems from ground-potential differences and common-mode transients while supporting point-to-point and multidrop RS-485 or RS-422 communication networks. The MAX1480CCPI+ uses a reduced-slew-rate driver to minimize electromagnetic interference and reduce reflected signaling on the bus. Its isolated outputs are stated to meet RS-485 and RS-422 specifications. Because one 5 V supply on the logic side powers both sides of the interface, the system does not require a separate isolated bus-side supply in the intended operating arrangement. The half-duplex architecture supports bidirectional communication over a shared differential pair when the application controls driver and receiver direction. The MAX1480C family is implemented as a hybrid microcircuit in a 28-pin DIP package. The isolated interface integrates the physical-layer transceiver and isolation barrier rather than requiring a discrete optocoupler, transformer, and driver-receiver arrangement. This reduces component count and simplifies the physical isolation implementation, but designers must still account for creepage, isolation boundaries, bus termination, grounding, and protection requirements at the board level. Typical uses include isolated RS-485 links in industrial controllers, HVAC and building-control networks, automated test equipment, local-area networks, and isolated data interfaces operating in EMI-sensitive environments. A 250 kbps data rate is suitable for moderate-speed supervisory, monitoring, and control traffic rather than the highest-speed industrial Ethernet protocols. The 28-pin through-hole DIP package also favors legacy, repairable, and industrial control-board designs. When designing around the MAX1480CCPI+, place the device so its isolation boundary remains clearly defined, connect the logic ground and bus ground to their respective domains, and follow the bus-interface recommendations in the manufacturer datasheet. Termination, protection, and common-mode requirements depend on cable length, topology, and the external transceiver used. This page consolidates verified manufacturer and distributor information, drop-in alternatives, pricing, and practical selection guidance beyond a basic distributor listing.

詢價 聯絡我們
MAX1480CEPI+ - Isolated RS-485/RS-422 Transceiver, 28-PDIP | Analog Devices
MAX1480CEPI+

MAX1480CEPI+ - Isolated RS-485/RS-422 Transceiver, 28-PDIP | Analog Devices

Analog Devices MAX1480CEPI+ is a 1/1 half-duplex transceiver for RS-485 and RS-422 data communications, packaged in a 28-pin DIP (through-hole) package. The device is a complete electrically isolated data interface in a hybrid microcircuit, so the logic side and the bus side are galvanically separated without requiring a separate isolation supply: a single +5 V supply on the logic side powers both sides of the interface. The MAX1480A/B/C family shares one 28-pin DIP footprint, so MAX1480CEPI+ is a pin-compatible member of a mature, widely deployed isolated transceiver line. An isolated RS-485/RS-422 transceiver is a differential line-driver and differential receiver combined with a galvanic isolation barrier. It sits in the interface hierarchy between a host UART or micro-controller and a long, noisy differential cable: interface IC -> line transceiver -> RS-485/RS-422 physical layer -> industrial control network. Isolation protects the host from ground-potential differences and surge events common in building control, HVAC and factory automation networks. Key characteristics of the MAX1480CEPI+ include reduced-slew-rate driver outputs (shared with the MAX1480B and MAX1480C variants) that minimize radiated EMI on the bus, a half-duplex 1/1 driver/receiver arrangement, and an industrial temperature grade in a through-hole rectangular DIP package. Because the C variant is specified for reduced EMI rather than maximum raw data rate, it is a better fit for long cables and electrically noisy installations than the faster MAX1480A. Internally, the MAX1480 series combines a pulse-transformer isolation barrier with driver and receiver circuitry in a single hybrid microcircuit. This topology provides reinforced isolation without optocoupler aging, and the isolation capacitance and creepage are defined by the package geometry rather than by a discrete isolation IC layout, so layout complexity at the board level stays low. Bus-side supply is generated on the isolated side, so no isolated DC-DC module is required at the board level. Typical applications include automated test equipment (ATE), HVAC and building-control networks, industrial-control local area networks, isolated RS-485/RS-422 data interfaces, and isolated transceiver links for EMI-sensitive equipment. The 28-pin through-hole package also suits legacy industrial boards, long-lifecycle instruments and field-upgrade programs where SMD parts are impractical. Design consideration: the isolation barrier means the bus-side ground is electrically separate from logic ground, so the bus-side return must be routed to a dedicated isolated ground plane that joins the shield at a single point. Also verify that the data rate, common-mode range and isolation withstand voltage of your chosen variant match your bus before substituting across the A/B/C grades. This page consolidates manufacturer and distributor data for MAX1480CEPI+, pin-compatible drop-in alternatives from the MAX1480 family, and practical design notes on isolation, grounding and EMI that are not presented together in the original datasheet listings.

詢價 聯絡我們
MAX1480EACPI+ - 2.5Mbps Isolated RS-485/422 | ADI
MAX1480EACPI+

MAX1480EACPI+ - 2.5Mbps Isolated RS-485/422 | ADI

The Analog Devices MAX1480EACPI+ is an isolated, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a 2.5 Mbps maximum data rate, and a 28-pin PDIP package. It operates from a 4.5 V to 5.5 V supply and provides 15 kV ESD protection on the communications interfaces. An isolated RS-485/RS-422 transceiver is a data-interface circuit that transfers digital signals between systems while providing electrical isolation between the host logic and the cable-side network. The MAX1480EACPI+ combines a differential line driver, differential receiver, isolation barrier, fail-safe receiver circuitry, and low-power standby capability. This places it within the transceiver hierarchy of interface ICs, communication ICs, and industrial data-conversion components. The principal benefits are its 2.5 Mbps operating speed, 15 kV ESD protection, isolated outputs, and support for both RS-485 and RS-422 networks. The device is particularly useful where a controller must connect to a long or electrically noisy cable without exposing the local electronics directly to the bus environment. Its integrated isolation also helps suppress ground-potential and common-mode disturbances between connected equipment. MAX1480EA-series devices use unrestricted driver slew rates for higher-speed communication, whereas MAX1480EC-series devices use reduced slew rates to minimize electromagnetic interference and cable reflections at lower data rates. The MAX1480EACPI+ is therefore most appropriate for links requiring the faster 2.5 Mbps capability rather than reduced-slew-rate operation. Its half-duplex arrangement supports a shared bus when only one transmitter is active at a time. Typical applications include automated test equipment, industrial-control networks, building-control systems, local area networks, telecom equipment, and isolated RS-485 or RS-422 data interfaces for EMI-sensitive installations. The 28-pin PDIP package favors legacy through-hole industrial equipment, test systems, and prototype platforms that have been designed around a conventional DIP footprint. For a new PCB, verify the complete pin description and isolation requirements in the manufacturer datasheet before assigning external nodes. Use appropriate bus protection, cable termination, grounding, and isolation barriers at the system level; the integrated 15 kV ESD protection does not remove the need for a sound surge and cabling strategy. This page consolidates the verified electrical ratings, package information, temperature range, and application requirements while adding engineering guidance for bus layout, protection, and component selection. It also identifies a temperature-grade alternative and clearly distinguishes the limits of the available drop-in replacement set.

詢價 聯絡我們
MAX1480EAEPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices
MAX1480EAEPI+

MAX1480EAEPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX1480EAEPI+ is an isolated RS-485/RS-422 data-interface transceiver with one driver and one receiver, a 4.5 V to 5.5 V supply range, and ±15 kV ESD protection. It is housed in a 28-pin plastic DIP package and is intended for isolated, noise-sensitive industrial communication links. An isolated RS-485/RS-422 transceiver is a semiconductor interface that combines differential line-driver and receiver functions with electrical isolation between the logic-side and bus-side circuits. In the hierarchy of electronic components, it is an interface transceiver, then a line driver and receiver, and finally a data-communication semiconductor. The MAX1480EAEPI+ supports both RS-485 and RS-422 networks while separating sensitive logic equipment from the communication cable. Key features include ±15 kV ESD protection on the I/O pins, single-side power isolation, a fail-safe receiver circuit, and low-power standby operation. The 4.5 V to 5.5 V operating supply supports conventional 5 V equipment, while the differential interface helps reject common-mode noise picked up by long cables. The listed operating temperature range is 0°C to +70°C. The MAX1480EAEPI+ is implemented as a complete isolated data interface rather than a simple line transceiver. Its hybrid construction provides both driver and receiver functions on one board, reducing the number of components needed for a bidirectional isolated link. Its 28-PDIP format supports through-hole assembly and straightforward prototype or repair work where a surface-mount isolator is unnecessary. Typical applications include industrial-control networks, building-control networks, automated test equipment, local-area networks, telecom transceivers, and other EMI-sensitive RS-485 or RS-422 links. The isolation barrier can help limit ground-potential and surge-related stress between a host controller and an externally connected bus. For a new design, confirm the transceiver voltage, temperature range, isolation requirements, bus loading, termination strategy, and ESD environment before assigning the DIP footprint. Keep bus-side and logic-side return paths separated according to the manufacturer datasheet, and place protective network components close to the connector when additional surge protection is required. This product page combines the manufacturer family information with distributor specifications, package details, drop-in-family comparisons, and practical interface-design guidance. It helps engineers identify whether the MAX1480EAEPI+ matches a legacy 28-pin isolated RS-485/RS-422 design and where additional qualification is required before substitution.

詢價 聯絡我們
MAX1480ECCPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices
MAX1480ECCPI+

MAX1480ECCPI+ - Isolated RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX1480ECCPI+ is an isolated RS-485/RS-422 data-interface transceiver with one driver and one receiver, ±15 kV ESD protection, and a 4.5 V to 5.5 V supply range. The device is housed in a 28-pin PDIP package. It is designed for industrial communication links that benefit from galvanic isolation and robust protection against electrostatic discharge. An RS-485/RS-422 transceiver is an interface integrated circuit that combines differential line-driver and receiver functions for reliable, noise-resistant data transmission over balanced wiring. The MAX1480ECCPI+ belongs to the broader interface IC hierarchy, where it connects digital logic to industrial communication buses. Its isolated transmitter and receiver reduce conductive noise paths between a host system and an external RS-485 or RS-422 network, improving robustness where ground-potential differences or long cables are concerns. Key characteristics include ±15 kV ESD protection, 4.5 V to 5.5 V operation, one differential driver, one differential receiver, and operation with both RS-485 and RS-422 networks. The 28-pin PDIP package supports through-hole assembly and straightforward inspection or rework. The component is specifically listed for new designs by the manufacturer through the MAX1480E family page. The MAX1480ECCPI+ combines a data-interface transceiver with isolation in a single package. This simplifies board partitioning compared with a non-isolated transceiver plus separate isolation components. Isolation-related timing, creepage, capacitance, and transient-protection details should nevertheless be checked against the complete manufacturer datasheet before finalizing a high-speed or high-noise design. Typical applications include isolated industrial RS-485 links, factory automation equipment, building-control systems, instrumentation, data acquisition, and communications equipment. The differential interface is particularly useful when the bus must tolerate electrically noisy industrial environments while maintaining a clear separation between equipment-ground domains. Designers should preserve the recommended isolation barrier, provide adequate input and output bypassing, route the isolated bus through appropriately protected interfaces, and account for connector-level surge and ESD requirements. The ±15 kV device rating does not eliminate the need for correct system grounding, cable routing, and external protection. This product page consolidates the manufacturer family information, interface characteristics, drop-in family alternatives, and application-specific engineering guidance. It is intended to help designers evaluate the MAX1480ECCPI+ for isolated RS-485 and RS-422 communication systems without relying on isolated snippets from individual listings.

詢價 聯絡我們
MAX1480ECEPI+ - Isolated RS-485/RS-422 Transceiver | Analog
MAX1480ECEPI+

MAX1480ECEPI+ - Isolated RS-485/RS-422 Transceiver | Analog

Analog Devices MAX1480ECEPI+ is an isolated RS-485/RS-422 data-interface transceiver with one driver and four receivers, a 4.5 V to 5.5 V supply range, and a 28-pin PDIP package. The interface provides ±15 kV ESD protection for industrial data lines while galvanic isolation separates the bus side from the logic side. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts digital logic signals into differential bus levels and receives differential bus signals. In the component hierarchy, it belongs to interface ICs and data transceivers, supporting the larger category of communication semiconductors. Its isolation function helps prevent ground-potential differences and common-mode transients from coupling between equipment and a remote bus. The MAX1480ECEPI+ combines one transmit driver with four receive channels in one 28-pin package. Its 4.5 V to 5.5 V operating supply supports conventional 5 V communication equipment. The ±15 kV ESD rating is the principal protection figure specified for exposed data-interface pins, making the device suitable for industrial environments where cables can acquire electrostatic discharge before reaching the equipment. This device is intended for isolated RS-485 and RS-422 links used to connect controllers, sensors, data-acquisition equipment, and remote instrumentation. The single-driver, four-receiver arrangement supports a point-to-multipoint topology when the bus wiring, termination, and grounding strategy are designed correctly. RS-422 favors point-to-point or one-driver configurations, while RS-485 permits multiple drivers under controlled bus management. A principal design consideration is that isolation does not replace correct bus engineering. The data lines still require suitable protection, cable routing, characteristic-impedance control, termination at appropriate endpoints, and common-mode analysis. The ±15 kV ESD capability should also be understood as an interface protection specification rather than a guarantee against every external surge event. Engineers should consult the manufacturer datasheet for the complete pin-description table, isolation ratings, timing, recommended application circuit, and package dimensions before assigning PCB tracks. DIP-28 construction also requires adequate spacing for through-hole assembly and should be checked against the enclosure, connector, and thermal requirements of the final system. This page combines the confirmed interface, supply, protection, package, and topology characteristics with application guidance, a parameter-level comparison, and actionable layout considerations. It is designed to help engineers identify the correct isolated transceiver while separating confirmed device facts from parameters that require review in the manufacturer documentation.

詢價 聯絡我們
MAX14821ETG+ - IO-Link Device Transceiver, 24-TQFN | Analog Devices
MAX14821ETG+

MAX14821ETG+ - IO-Link Device Transceiver, 24-TQFN | Analog Devices

The Analog Devices MAX14821ETG+ is an IO-Link device transceiver in a 24-pin TQFN (4x4 mm) package designed for industrial sensor and actuator networks operating on the 24V IO-Link standard. It supports all IO-Link data rates (COM1/COM2/COM3 at 4.8/38.4/230.4 kbps), operates from a 9V to 36V supply range, and integrates C/Q and DO drivers that are independently configurable for push-pull, high-side (PNP), or low-side (NPN) operation. The device detects the IO-Link C/Q wake-up condition and generates a wake-up signal on the active-low WU output for microcontroller power management. Two internal linear regulators (3.3V and 5V) generate common sensor and microcontroller supply rails from the 24V bus, reducing BOM count in industrial sensor heads. An IO-Link device transceiver is a physical-layer interface IC that bridges a microcontroller (running the data-link layer protocol) to the 24V IO-Link master port on the fieldbus. In the broader taxonomy, it belongs to sensor interface ICs, then industrial interface ICs, then interface ICs, and ultimately the integrated circuits family. IO-Link (IEC 61131-9) is a point-to-point, bidirectional digital communication standard that replaces traditional 4-20 mA and binary 24V signaling with a single standardized cable carrying both power and process data, enabling predictive maintenance and rich diagnostic data on factory floors. Key features of the MAX14821ETG+ include 1/1 transceiver topology, integrated surge protection for industrial 24V lines, selectable C/Q and DI current loads for actuator use, and a wide -40C to +85C industrial operating temperature range. The C/Q driver is rated for the high-current switching demanded by industrial actuators, while the DI (digital input) and DO (digital output) channels support legacy 24V binary sensor and actuator signaling. The integrated 5V/3.3V LDO outputs eliminate the need for external regulators in most sensor head designs, while the WU output pin enables ultra-low-power sleep modes for IO-Link-compliant wake-up sequences. From an architectural standpoint, the MAX14821ETG+ integrates the 24V physical layer, two LDO regulators, surge/transient protection, and configurable driver stages into a single die. This level of integration allows a complete IO-Link device node to be built with the MAX14821ETG+, a microcontroller, and minimal external passives. The device is designed to meet IEC 61131-9 IO-Link specifications and the IEC 61000-4-2 ESD and surge immunity requirements typical of industrial 24V environments. Typical applications include IO-Link smart sensors (photoelectric, inductive, capacitive, pressure), IO-Link valve manifolds and binary actuators, industrial 24V binary sensors with wake-up capability, and factory automation I/O modules. It is also well-suited for distributed I/O blocks, proximity switches, and condition-monitoring sensor heads where the 24V bus doubles as both power supply and communication line. When designing with this transceiver, ensure that the C/Q and DO driver configurations match the connected load (sink vs source) before commissioning, and place the bulk 24V decoupling capacitor close to the VSUP pin to ride through industrial surge events. Designers should also account for the thermal dissipation of the integrated LDOs when sourcing 100 mA continuously to the microcontroller rail. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes that go beyond what is reproduced in the manufacturer datasheet, helping engineers accelerate their IO-Link device development and source decisions.

詢價 聯絡我們
MAX14850ASE+ - 6-Channel 600Vrms Digital Isolator | Analog Devices
MAX14850ASE+

MAX14850ASE+ - 6-Channel 600Vrms Digital Isolator | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX14850ASE+ is a six-channel digital isolator in a 16-pin SOIC (NSOIC) package that delivers up to 50 Mbps signaling and 600 Vrms isolation voltage across a monolithic silicon-dioxide barrier. It supports 3 V to 5.5 V power domains on both sides of the isolation barrier, a 1.5 kV/us minimum common-mode transient immunity (CMTI), and 30 ns typical propagation delay. A digital isolator is a semiconductor device that transfers logic signals across an isolation barrier using capacitive or magnetic coupling rather than opto-coupling or transformer coupling. Isolators sit in the system hierarchy between level shifters (which do not provide galvanic isolation) and reinforced safety isolators (which add redundant barriers for medical and high-voltage applications). The MAX14850 family uses Maxim's proprietary monolithic process technology to integrate the isolation barrier and transceivers onto a single die, reducing BOM cost versus traditional optocoupler or discrete transformer solutions. Key features include 600 Vrms working voltage rating, 2.5 kVrms surge capability per IEC 61000-4-5 referenced in the manufacturer datasheet, six independent unidirectional channels configured as 3 forward / 3 reverse, low power consumption of 2.5 mA per channel at 1 Mbps, 25 kV/us typical CMTI, and a wide operating temperature range of -40 C to +105 C. The device requires no external components other than standard bypass capacitors on each supply pin. The MAX14850 architecture combines on-chip transformers or capacitive couplers with Manchester-style or pulse-encoded data transmission to achieve robust common-mode rejection. Its monolithic integration eliminates the LED aging and CTR degradation that affect optocouplers, yielding stable performance over temperature and end-product lifetime. Typical applications include isolated RS-485/RS-232 transceivers, industrial fieldbus (Modbus, Profibus), isolated SPI and GPIO interfaces for microcontroller I/O expansion, medical patient-monitoring equipment requiring 1 x MOPP, solar inverter gate-drive signal isolation, and battery management systems in electric vehicles. When designing with this part, ensure each VDD pin is bypassed with a 0.1 uF ceramic capacitor placed within 2 mm of the IC body, and route high-speed signal traces on the inner PCB layers using a controlled-impedance stack-up to maintain signal integrity across the isolation barrier. Confirm that the board-level creepage and clearance distances for the 600 Vrms rating meet the application's pollution-degree and altitude derating requirements per IEC 60664-1.

詢價 聯絡我們
MAX14851AEE+ - 6-Ch 600Vrms Digital Isolator, 2Mbps/50Mbps | Analog Devices
MAX14851AEE+

MAX14851AEE+ - 6-Ch 600Vrms Digital Isolator, 2Mbps/50Mbps | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX14851AEE+ is a six-channel digital isolator delivering 600Vrms isolation with 2Mbps default data rate and a 50Mbps high-speed option in a 16-pin SSOP (QSOP) package. It features monolithic Maxim process technology providing compact, low-cost isolation between circuits operating from independent 3V to 5.5V supplies on each side of the barrier. The device provides a minimum common-mode transient immunity (CMTI) of 3.2 kV/us and is the industry first monolithic 600Vrms digital isolator. A digital isolator is an integrated circuit that transfers logic signals between two voltage domains while maintaining galvanic isolation - a safety barrier that blocks DC and low-frequency AC while allowing high-frequency digital edges to pass. Isolators belong to the signal isolation family, which sits between interface ICs and power management in the broader semiconductor hierarchy. They are essential for breaking ground loops, protecting low-voltage logic from high-voltage transients, and meeting safety standards such as IEC 60747-17 / UL 1577 for reinforced insulation. Key features of the MAX14851AEE+ include six unidirectional channels configurable as forward/reverse combinations, 11.8 ns typical propagation delay, 3V to 5.5V independent supply on each side (suitable as a level translator), 600Vrms working voltage per UL 1577, and an extended -40C to +125C operating temperature range. Independent supply ranges also make the device suitable as a logic-level translator between 3.3V and 5V systems without external circuitry. The MAX14851 uses Maxim's proprietary monolithic isolation process, embedding the isolation barrier on the same silicon die rather than relying on transformer or optical coupling. This monolithic approach achieves lower power consumption and higher channel density than multi-chip alternatives while eliminating the discrete transformer or optocoupler BOM. Typical applications include isolating SPI buses between an MCU and a sensor front-end, isolating I2C and RS-232/RS-485/RS-422 transceivers in industrial fieldbus nodes, general-purpose GPIO isolation in PLC and motor-drive digital interfaces, and level translation between mixed-voltage MCUs and 5V peripherals. Six channels are well matched to 4-wire SPI plus chip-select and one extra GPIO for fault or reset signaling. When designing with the MAX14851AEE+, route the four inner ground pins (GND1/GND2) carefully to maintain barrier creepage and clearance. Place 0.1 uF + 10 uF decoupling on both VDDA and VDDB as close to the IC as possible. Avoid running high-speed traces under the device to preserve creepage on the SSOP body. This page synthesizes distributor pricing, drop-in alternatives, and design notes that are not consolidated in the manufacturer datasheet, including a side-by-side comparison with same-package isolators.

詢價 聯絡我們
MAX14852GWE+ - 2.75kV Isolated RS-485/RS-422 Transceiver | Maxim Integrated
MAX14852GWE+

MAX14852GWE+ - 2.75kV Isolated RS-485/RS-422 Transceiver | Maxim Integrated

The Maxim Integrated (now Analog Devices) MAX14852GWE+ is a 2.75kVRMS isolated, full-duplex RS-485/RS-422 transceiver housed in a 16-pin wide-body SOIC (WSOIC) package. It supports data rates of 500 kbps (low-speed mode) and 25 Mbps (high-speed mode), operates from a 1.71V to 5.5V supply on both the UART and cable-side domains, and provides 35 kV ESD protection (HBM) on the bus pins per the Maxim datasheet. An isolated RS-485 transceiver is a bus interface IC that combines a standard differential line transceiver with on-chip galvanic isolation. Isolation breaks ground loops, eliminates common-mode voltage damage, and rejects large ground-potential differences between system nodes. Within a typical industrial system, the MAX14852 sits between a microcontroller UART and the RS-485 bus, sitting in the signal-chain layer between the controller SoC and the field wiring. Key features of the MAX14852GWE+ include integrated transformer-driver isolation (no external transformers or optocouplers required), 1 driver / 1 receiver full-duplex configuration, true fail-safe receiver inputs, hot-swap capability on the bus side, and a low supply current that suits battery-backed or always-on industrial nodes. The wide-body SOIC package provides the minimum 8 mm of creepage/clearance required for 2.75 kVRMS reinforced isolation per IEC 60950 / IEC 62368. Technically, the MAX14852 uses Maxim's proprietary iso-loop isolation technology to embed an isolation barrier and DC-DC drive directly inside the IC, eliminating the need for an external isolated power supply on the cable side. The 2.75 kVRMS rating is verified for 60 seconds and the part is rated for -40 °C to +105 °C operation, suitable for outdoor cabinet and industrial-control environments. Typical applications include isolated Modbus RTU links in PLCs, RS-485 repeaters/bridges, solar inverter monitoring, building automation gateways, and any industrial node requiring robust ground isolation. Compared with optocoupler-plus-isolated-DC/DC discrete implementations, the MAX14852 reduces BOM count, PCB area, and design time. When designing with this device, allocate the WSOIC-16 footprint on the PCB with adequate clearance under the package to preserve the 2.75 kV rating, and bypass both VDD pins with 0.1 µF + 10 µF capacitors placed within a few millimeters of the pins. Note that the MAX14852GWE+ and MAX14854GWE+ differ in data-rate grade (500 kbps/25 Mbps vs 25 Mbps fixed). This page synthesizes drop-in alternatives in the WSOIC-16 package, distributor pricing tiers, and practical PCB layout/design notes that go beyond what is shown on Maxim/Analog Devices product pages.

詢價 聯絡我們
MAX14854GWE+ - 25Mbps Isolated RS-485/RS-422 | Analog Devices
MAX14854GWE+

MAX14854GWE+ - 25Mbps Isolated RS-485/RS-422 | Analog Devices

The Analog Devices MAX14854GWE+ is a 25Mbps isolated full-duplex RS-485/RS-422 transceiver with 2.75kV RMS galvanic isolation, 35kV ESD protection, and a 16-pin wide SOIC package. It supports a 1.71V to 5.5V supply range and integrates one driver and one receiver for robust point-to-point or multipoint serial links. The isolation barrier separates the cable-side driver and receiver from the UART-side circuitry. An isolated RS-485/RS-422 transceiver is an interface IC that translates logic-level signals into differential cable signals while providing galvanic isolation between equipment domains. Galvanic isolation breaks ground loops, reduces common-mode noise, and protects low-voltage UART electronics from cable-side transients. This makes the MAX14854GWE+ suitable for industrial communication, test equipment, building controls, and systems where the host and cable grounds may be at different potentials. The device supports operation from 1.71V to 5.5V, data rates up to 25Mbps in the high-speed mode, and lower-rate operation down to 500kbps according to the manufacturer product description. Its full-duplex architecture supports separate transmit and receive paths, while the integrated isolation barrier provides 2750V RMS for 60 seconds. The cable interface includes ±35kV ESD protection, a significant advantage in connector environments where electrostatic discharge is a recurring threat. The MAX14854 family is designed for robust differential serial communication where isolated voltage levels and high data throughput are both important. The MAX14854GWE+ combines an integrated isolation barrier with RS-485/RS-422 driver and receiver functions, reducing the number of external isolation components required. Its wide-body SOIC package is intended for surface-mount industrial equipment and is compatible with automated assembly. Typical applications include industrial RS-485 links, isolated UART bridges, factory equipment interfaces, building automation, instrumentation, and communications between controllers and remote sensors. The full-duplex configuration is especially useful when simultaneous transmit and receive operation is required, while the isolation rating supports dependable communication across equipment boundaries. Designers should verify supply voltage, baud-rate mode, termination, fail-safe biasing, isolation requirements, and cable-side protection before layout. Place the isolation-related components and differential traces according to the manufacturer datasheet, and keep the logic-side and cable-side ground domains physically separated. The MAX14854GWE+ is an active, leaded surface-mount device identified by the GWE+ ordering suffix.

詢價 聯絡我們
MAX14882AWE - 5kVRMS Isolated CAN Transceiver, 1Mbps, 16-SOIC
MAX14882AWE

MAX14882AWE - 5kVRMS Isolated CAN Transceiver, 1Mbps, 16-SOIC

The Analog Devices (formerly Maxim Integrated) MAX14882AWE is a 5kVRMS galvanically-isolated high-speed CAN transceiver housed in a 16-pin wide-body SOIC (WSOIC) package. It operates at data rates up to 1Mbps and provides 5000VRMS (60s) of isolation between the CAN-protocol controller-side (TXD, RXD) and the physical bus-side wires (CANH, CANL), integrating the isolation barrier, an isolated DC-DC transformer driver, and an LDO for bus-side power. A CAN transceiver is a physical-layer interface IC that translates the differential CAN protocol from a microcontroller into the robust voltage levels required on a CAN bus, while providing protection against ground loops, common-mode transients, and bus faults. Isolated CAN transceivers additionally place a galvanic barrier between the controller and the bus, eliminating ground-potential differences and surge propagation in industrial environments. The MAX14882AWE falls in the hierarchy: CAN transceiver -> automotive/industrial bus interface IC -> interface IC -> integrated circuit. Key features include a ±25V receiver common-mode input range (exceeding the ISO 11898-2 requirement of -2V to +7V), ±54V fault-tolerant CANH/CANL outputs, and ±15kV HBM ESD protection on the bus-side pins to GNDB. The controller-side operates from VDDA = 3.0V to 5.5V, while the bus-side runs from VDDB = 4.5V to 5.5V with an integrated transformer driver that supports an external transformer for isolated supply rails. Operating temperature spans -40°C to +125°C. The device supports a low-power standby mode for remote-wakeup and an integrated POL (polarity swap) feature that swaps CANH and CANL functions to correct cross-wired cables via software. The wide-body SOIC package provides 8mm of creepage and clearance, satisfying IEC 60950 and IEC 62368 reinforced insulation requirements for industrial and renewable energy installations. Typical applications include isolated CAN nodes in solar inverters, industrial PLC backplanes, electric vehicle battery management systems (BMS), and any industrial network requiring robust galvanic isolation between the controller MCU and the noisy CAN bus cable plant. When designing with the MAX14882AWE, the external transformer (e.g., a 1:1.3 or 1:1 turns ratio miniature transformer) is the critical BOM item that determines the isolated bus-side rail voltage and overall efficiency. PCB layout must maintain 8mm creepage across the WSOIC body and avoid copper traces under the package to preserve the reinforced insulation barrier. This page synthesizes drop-in alternatives, distributor pricing as of 2026-10-16, design notes, and a side-by-side comparison versus MAX14882 family variants and competing isolated CAN transceivers not found in the manufacturer datasheet alone.

詢價 聯絡我們
MAX14882AWE+T - 5kVRMS Isolated CAN Transceiver | Analog Devices
MAX14882AWE+T

MAX14882AWE+T - 5kVRMS Isolated CAN Transceiver | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX14882AWE+T is a 5kVRMS isolated high-speed CAN transceiver that integrates galvanic isolation between the CAN-protocol controller side (TXD, RXD) and the physical CAN bus wires (CANH, CANL), delivering 1Mbps data rate over a 3.0V to 5.5V controller-side supply and 4.5V to 5.5V bus-side supply in a 16-pin wide-body SOIC (W SOIC) package with 8mm of creepage and clearance. What is an isolated CAN transceiver? A CAN (Controller Area Network) transceiver is the physical-layer interface between a digital CAN protocol controller and the differential CAN bus cables. An "isolated" variant adds a galvanic isolation barrier (here, 5kVRMS) that breaks ground loops, rejects common-mode transients, and protects low-voltage microcontrollers from high-voltage faults on the industrial CAN bus. The MAX14882 sits in the product hierarchy: CAN transceiver -> automotive/industrial transceiver -> isolated interface IC -> power management and signal conditioning IC family. Key features include a ±25V receiver input common-mode range (exceeding the ISO 11898-2 requirement of -2V to +7V), ±54V fault tolerance on CANH/CANL, ±15kV HBM ESD protection on bus-side pins to GNDB, an integrated transformer driver with LDO that supplies VDDB from an external transformer, and a POL (polarity) pin that swaps CANH/CANL functions for software correction of cross-wired bus cables. The integrated isolation eliminates the need for a discrete digital isolator plus an external isolated DC/DC supply, reducing BOM count and PCB footprint by roughly 50%. Typical applications include industrial automation networks (CANopen, DeviceNet), building automation HVAC controllers, solar inverter inter-module communication, electric vehicle battery management systems (CAN-FD ready), and any microcontroller-to-bus interface requiring robust galvanic isolation in harsh electrical environments. When designing with this part, place decoupling capacitors (typically 100nF plus 10µF) on both VDDA and VDDB as close to the IC as possible, and route the external transformer primary traces symmetrically. The integrated LDO can source up to 300mA for auxiliary circuits after supplying the internal 130mA MAX14882 load, but derate at high bus-side temperatures.

詢價 聯絡我們
MAX148ACAP+T - 10-Bit 8-Ch SAR ADC 133ksps 20-SSOP | Maxim
MAX148ACAP+T

MAX148ACAP+T - 10-Bit 8-Ch SAR ADC 133ksps 20-SSOP | Maxim

The Maxim Integrated (Analog Devices) MAX148ACAP+T is a 10-bit, 8-channel, low-power successive-approximation analog-to-digital converter (SAR ADC) with a 133 ksps sampling rate in a 20-pin SSOP package. The "A" suffix denotes the extended sampling-rate grade (133 ksps vs 90 ksps for the MAX148B/C grades), and the "CAP" suffix denotes the 20-pin SSOP with commercial temperature grade (0C to +70C). The "+T" suffix indicates Tape & Reel packaging. A SAR ADC is a type of analog-to-digital converter that uses a binary search through each bit to approximate the input voltage, performing one conversion per N clock cycles (N = resolution in bits). SAR ADCs excel at medium-speed, medium-resolution conversions with deterministic latency, no pipeline delay, and very low power consumption, which is why they dominate battery-powered industrial sensor, panel-meter, and data-acquisition applications. Key features of the MAX148ACAP+T include a single +2.7V to +5.25V supply (typically +5V), an 8-channel single-ended or 4-channel differential analog input multiplexer with high-bandwidth track/hold, an SPI/QSPI/MICROWIRE-compatible serial interface, hardware and software shutdown modes (less than 10 microA quiescent current in shutdown), and an internal 4.096V or external reference option. The MAX148 provides 0 to +5V unipolar input range with the internal reference. Architecture: the chip combines a track/hold front-end, an 8-to-1 analog mux, a charge-redistribution SAR core, and an internal reference. The internal reference is selectable to either 4.096V (for 0-5V unipolar input, MAX148) or 2.048V (for 0-2.5V unipolar input). The serial interface can clock up to 2.1 MHz, supporting full-speed conversions at the 133 ksps maximum rate. Typical applications include 4-20mA loop-powered industrial sensors, panel meters and digital multimeters, data-acquisition cards, portable instrumentation, and battery monitoring systems. Designers choose this part for its combination of 8 channels, low power, and small SSOP footprint. The trade-off versus higher-resolution ADCs (12, 14, 16-bit) is dynamic range. The MAX148 offers 10-bit resolution (about 60 dB SNR), so designs requiring better than 0.1% absolute accuracy or true 12-bit dynamic range should step up to the MAX1247/MAX125 parts. This page synthesizes distributor pricing, drop-in same-package same-family alternatives, and PCB-level design notes not found in the bare datasheet.

詢價 聯絡我們
MAX148AEPP+ - 10-Bit 8-Ch 133ksps 5.25V Precision ADC | Maxim Integrated
MAX148AEPP+

MAX148AEPP+ - 10-Bit 8-Ch 133ksps 5.25V Precision ADC | Maxim Integrated

The Maxim Integrated MAX148AEPP+ is a 10-bit, 8-channel, low-power serial-interface analog-to-digital converter (ADC) that combines an 8-channel analog multiplexer, a high-bandwidth track-and-hold, and a serial interface in a single 20-pin PDIP package. It operates from a single +2.7V to +5.25V supply, accepts up to 8 single-ended or 4 differential analog inputs, and delivers up to 133 ksps throughput while consuming only 1.2 mA (typ) at full sampling rate. What is a SAR ADC? A successive-approximation-register (SAR) analog-to-digital converter is a precision data-conversion architecture that builds the output code bit-by-bit using an internal DAC and comparator. SAR ADCs sit in the broader hierarchy of data converters (ADC) -> mixed-signal ICs -> signal chain ICs -> power management and analog semiconductors. They are favored for medium-speed, medium-resolution applications where deterministic latency, low power, and small package size matter more than the very high sampling rates of pipelined or sigma-delta ADCs. Key features include ±1 LSB INL and DNL (max) over the industrial -40°C to +85°C range, a hardware SHDN pin plus software-selectable power-down that drops supply current to under 10 µA between conversions, an external serial clock up to 2 MHz (SPI/QSPI/MICROWIRE compatible), and a flexible reference input accepting ratiometric conversions or an external 2.5V/4.096V reference. The internal MUX-S/H-ADC chain provides true 8-channel scanning with sequential or on-demand channel selection, and automatic shutdown at end-of-conversion further reduces system power in battery-driven designs. The MAX148 uses a charge-redistribution DAC core with an auto-calibrated comparator and a synchronous serial output that streams the conversion result MSB-first. The serial interface supports daisy-chaining multiple devices (CS line selects the active device), allowing multi-channel expansion without consuming additional microcontroller pins. The wide supply range and reference flexibility make it equally at home on a 3.3V logic rail or a 5V analog rail. Typical applications include portable data logging, 4-20 mA industrial sensor multiplexing, multi-cell battery monitoring, HVAC thermostat analog front ends, panel meters and digital multimeters, and distributed-control / SCADA analog input modules. The combination of 8-channel input mux, SPI interface, and 1.2 mA operating current also suits handheld medical and instrumentation designs where both channel density and battery life are critical. When designing with this device, choose an external reference (e.g. MAX6125 or REF02) when absolute accuracy is required; for ratiometric ratiometric bridge or thermistor measurements the supply can serve as the reference. Place a 0.1 µF decoupling capacitor directly at VDD and a 10 µF bulk capacitor at the analog supply pin to suppress digital switching noise that would otherwise couple into the SAR comparator. This page synthesizes distributor pricing (Mouser/DigiKey), cross-reference alternatives from the Maxim MAX148 family, and PCB-level design guidance that goes beyond the manufacturer datasheet, helping engineers evaluate a drop-in upgrade path quickly.

詢價 聯絡我們
MAX14931AASE+T - 4-Ch 1Mbps 2.75kVrms Digital Isolator | ADI
MAX14931AASE+T

MAX14931AASE+T - 4-Ch 1Mbps 2.75kVrms Digital Isolator | ADI

The Analog Devices (formerly Maxim Integrated) MAX14931AASE+T is a 4-channel, 2.75kVRMS digital isolator in a 16-pin wide-body SOIC package, supporting 1 Mbps data rate with a typical CMTI of 25 kV/µs. The device transfers digital signals across an isolation barrier using Maxim's proprietary process technology, and the 3/1 unidirectional channel configuration makes it well suited to SPI, RS-232, RS-485, and general-purpose digital I/O isolation. A digital isolator is a semiconductor device that uses an internal isolation barrier - typically a capacitive, magnetic, or optical coupling structure - to transmit logic-level signals between two galvanically isolated voltage domains while blocking DC and low-frequency currents. Digital isolators replace optocouplers in modern designs and are classified within the broader signal-chain and interface-IC family. They are key building blocks for reinforced insulation, functional safety, and high-voltage system partitioning. Key features of the MAX14931AASE+T include 2750 Vrms withstand voltage, 1 Mbps guaranteed data rate across -40 °C to +125 °C, 25 kV/µs typical common-mode transient immunity, low propagation delay of 42.9 ns, and 1.71 V minimum supply voltage. The wide-body SOIC-16 package provides the required creepage and clearance for reinforced isolation at 2.75 kVRMS, simplifying PCB layout for industrial bus isolation. Internally, the MAX14931AASE+T uses Maxim's proprietary CMOS isolation technology with integrated dc-dc converter control on the secondary side for optional isolated power. Each of the four channels is unidirectional, three in one direction and one in the reverse direction, matching typical SPI / UART peripheral-interface signalling patterns without requiring external direction-control logic. Typical applications include isolated SPI interfaces for industrial PLCs, isolated RS-485 transceivers in factory automation, isolated gate-drive signal conditioning for motor drives, and medical device patient-isolated data links. The wide operating temperature range supports both industrial and automotive-grade designs. When designing with this device, follow the SOIC-16 wide-body creepage and clearance guidelines: maintain at least 8 mm of PCB spacing under the package body and avoid routing copper traces between pins to preserve the 2.75 kVRMS rating. Decouple both VDD pins with 0.1 µF low-ESR ceramic capacitors placed within 2 mm of the supply pins.

詢價 聯絡我們