介面 IC
子分類
產品（3,100+)
TLE7251VSJXUMA1 - 2Mbps CAN Transceiver | Infineon
Infineon Technologies TLE7251VSJXUMA1 is a high-speed CAN bus transceiver with one transmitter and one receiver, operating at up to 2 Mbit/s from a 4.5 V to 5.5 V supply. The device is packaged in an 8-pin PG-DSO-8 surface-mount package and operates across the -40°C to +150°C automotive temperature range. A CAN transceiver, also called a CAN interface controller or CAN physical-layer transceiver, connects a host controller or microcontroller to the differential CAN bus. It converts digital logic-level TXD and RXD signals into the physical bus voltage and converts received bus states back into a logic-level signal. Within the interface hierarchy, this device sits between a CAN protocol controller and the CAN bus network. Principal characteristics include ISO 11898-2 compliance, a 2 Mbit/s data rate, low electromagnetic emissions, robust electromagnetic-interference and electrostatic-discharge protection, and a 90 mV receiver hysteresis. The operating supply current is listed as 2.6 mA in one operating condition and up to 38 mA in another, allowing the distinction between normal operation and a higher-current condition to be checked in the manufacturer datasheet. The automotive-grade temperature qualification and 8-pin DSO package make the transceiver suitable for compact vehicle-network electronics, including body controllers, gateways, infotainment modules, seat and door controllers, lighting controllers, and sensor nodes. Its ISO 11898-2 compatibility and high operating data rate also support industrial CAN systems requiring a standardized physical layer. Designers should provide a stable 5 V rail within the 4.5 V to 5.5 V range, connect CANH and CANL to the network through the application-appropriate bus interface, and verify termination and common-mode behavior. The high ambient-temperature capability does not remove the need to control package dissipation and board-level thermal exposure. This product page combines the manufacturer specifications, ordering information, lifecycle indication, package details, and application guidance into an engineering-focused reference. It also distinguishes documented drop-in migration options from devices that require different pin logic, supply requirements, or protection features.
TLE7257LEXUMA1 - 20 kbps LIN Transceiver | Infineon
Infineon Technologies TLE7257LEXUMA1 is an automotive LIN bus transceiver with one transmitter and one receiver, supporting data rates up to 20 kbps in an 8-pin PG-TSON-8-1 package. The device includes integrated wake-up and protection features for Local Interconnect Network communication in in-vehicle networks. A LIN transceiver is the physical-layer interface between a LIN protocol controller and a vehicle's LIN wiring. LIN is a low-cost, single-wire serial network used for distributed automotive functions such as body electronics, comfort controls, lighting, seat controls, and sensor nodes. The TLE7257LE translates logic-level signals between the controller and the physical LIN bus while supporting a maximum specified data rate of 20 kbps. The TLE7257LEXUMA1 provides one transmit channel and one receive channel for integration into a LIN node. Its integrated wake-up function supports low-power vehicle-network designs, while integrated protection features help the interface withstand the electrical conditions encountered in automotive wiring. The manufacturer identifies the device as ISO 17987-4 compliant, making it suitable for LIN physical-layer implementations requiring that interoperability specification. The PG-TSON-8-1 package uses eight pins and is intended for surface-mount PCB assembly. Its compact form factor is useful for electronic control units where the LIN interface must be placed close to the controller, connector, or protection network. Automotive qualification, production status, detailed electrical limits, exposed-pad construction, and ordering-code-specific attributes should be confirmed against the manufacturer ordering information before a safety-related or high-volume design is released. Typical applications include body-domain controllers, door and seat modules, climate-control equipment, lighting control modules, sensor interfaces, and other distributed automotive systems connected through a LIN bus. The transceiver can also be used in LIN gateways or diagnostic interfaces when the system controller requires a dedicated physical-layer transceiver. Design the LIN bus connection with the supply, ground, transceiver, connector, and external protection network arranged to minimize loop area and maintain signal integrity. Confirm the device's exact pin assignment, recommended external components, bus capacitance, pull-up implementation, and electrical limits in the manufacturer datasheet before PCB release. This product page combines the manufacturer LIN-interface description with distributor package and ordering information, while separating application guidance, selection trade-offs, and design checks that are not visible in a basic catalog listing.
TLE7257SJXUMA1 - 20 kbps LIN Transceiver | Infineon Technologies
Infineon Technologies TLE7257SJXUMA1 is an automotive LIN bus transceiver with integrated voltage regulator, 20 kbps data-rate support, wake-up functionality, and bus protection features in an 8-pin PG-DSO-8 surface-mount package. The device supports in-vehicle LIN networks and is identified as ISO 17987-4 compliant by the manufacturer. A LIN transceiver is an interface integrated circuit that connects a host microcontroller or cluster controller to a single-wire Local Interconnect Network bus. The LIN bus belongs to the vehicle-network interface hierarchy, where physical-layer transceivers translate logic-level controller signals into bus-level signals and recover received data for the host processor. Key features include support for data transmission rates up to 20 kbps, integrated wake-up, protection features, and an integrated voltage regulator. The PG-DSO-8 package matches the verified 8-SOIC, 3.90 mm-wide package designation. Its operating temperature range extends from -40 °C to 150 °C, making it appropriate for harsh automotive environments when the complete device qualification and system requirements are satisfied. The TLE7257SJXUMA1 is listed for automotive AEC-Q100 applications and operates in a vehicle-network IC role. Its integrated regulator can support implementation of a protected transceiver supply, while the wake-up and protection functions reduce the external circuitry needed for a robust LIN node. Exact regulator output, supply limits, thresholds, and electrical timing values are not included in the supplied verified data and should be confirmed in the manufacturer datasheet. Typical applications include LIN slave nodes in body-control modules, door and seat modules, climate-control equipment, lighting controllers, sensors, and other low-speed vehicle subsystems. Its 20 kbps capability matches LIN networks commonly used for distributed automotive body electronics, where deterministic communication and robust fault handling are more important than high-bandwidth performance. When designing a PCB around the TLE7257SJXUMA1, use the manufacturer reference layout and verify bus termination, pull-up implementation, supply decoupling, and exposed-pad or thermal requirements for the exact PG-DSO-8 land pattern. Because the supplied data does not include a verified pin table, engineers should obtain the official pinout before routing the transceiver pins. This page consolidates verified manufacturer and distributor information, automotive-interface specifications, application guidance, and replacement considerations. It also clearly separates confirmed characteristics from parameters that require confirmation from the official datasheet, helping engineers evaluate the LIN transceiver without relying on unverified generic part data.
TLE7258DXUMA1 - 20kbps LIN Transceiver | Infineon
The Infineon TLE7258DXUMA1 is an automotive LIN bus transceiver with one transmitter and one receiver, a maximum data rate of 20 kbps, and integrated wake-up and protection features. It operates from a 5.5 V to 18 V supply in an 8-pin PG-TSON-8-1 surface-mount package, with an exposed pad and an operating-temperature range of -40°C to 150°C. The device is associated with automotive AEC-Q100 qualification and ISO 17987-4 LIN compliance. A LIN transceiver is an interface IC that connects a host microcontroller or slave node to the single-wire Local Interconnect Network used in automotive and low-speed serial networks. LIN sits within the broader hierarchy of transceiver, communication interface IC, and semiconductor categories. Its single-wire physical layer reduces wiring compared with a multiwire bus while supporting predictable frame-based communication between automotive electronic control units. The TLE7258DXUMA1 provides a 1/1 transmitter-to-receiver arrangement, a 20 kbps maximum LIN data rate, and 120 mV receiver hysteresis. The 120 mV hysteresis helps distinguish valid logic levels when the bus is noisy. Integrated wake-up functionality supports low-power vehicle networks, while integrated protection features increase robustness against the electrical conditions encountered in automotive wiring harnesses. The device is designed around a 5.5 V to 18 V operating-supply range. This range allows the transceiver to operate from a conventional automotive low-voltage supply while providing margin relative to the nominal 12 V vehicle rail. The integrated architecture places the LIN physical-layer driver and receiver in a compact exposed-pad package, allowing the PCB to provide both electrical connection and a thermal path during operation. Typical uses include LIN slave nodes, body-control modules, door and seat controllers, climate-control interfaces, ambient-light sensors, and other automotive accessory networks. The part is appropriate when a controller needs a standards-based LIN physical-layer interface and the network operates at 20 kbps or below. A host microcontroller still handles frame construction, checksums, scheduling, diagnostics, and higher-level application logic. For PCB design, place the transceiver close to the LIN connection and route the bus away from switching nodes and high-current paths. The exposed pad should be connected to the ground-plane structure specified by the manufacturer and thermal design should be checked across the full -40°C to 150°C operating range. Input and output component selection must follow the manufacturer application circuit rather than generic interface assumptions. This product record combines verified distributor information, manufacturer-series compatibility data, lifecycle evidence, pricing references, and practical design guidance. It also distinguishes verified electrical facts from parameters that still require confirmation from the exact ordering code and manufacturer datasheet, helping engineers shorten obsolete-part assessment without implying unverified drop-in equivalence.
TLE7258LEXUMA1 - 20 kbps LIN Bus Transceiver | Infineon
Infineon Technologies TLE7258LEXUMA1 is an automotive LIN bus half transceiver supporting 20 kbps data rates, operating from a 5.5 V to 18 V supply with 3 mA supply current, and housed in the 8-pin PG-TSON-8-1 surface-mount package built on BiCMOS process technology. A LIN transceiver is a physical-layer interface device that connects a microcontroller to a LIN (Local Interconnect Network) sub-network. LIN is a low-cost, single-wire, master-slave serial bus standardized for vehicle body electronics, where a full CAN network would be overkill. The hierarchy runs from LIN transceiver to automotive interface IC to interface IC to integrated circuit, and it sits at the boundary between the host MCU and the physical bus wiring. Key features include a 20 kbps LIN data rate, ISO 17987-4 compliance, a single transceiver channel (1/1) for point-to-point LIN nodes, low 3 mA supply current for sleep-friendly body modules, and MSL 2A moisture sensitivity handling for standard reflow assembly. The BiCMOS process combines bipolar output drivers with CMOS control logic, which is what allows the transceiver to deliver usable bus levels while drawing very little standby current. Architecturally, the device bridges a logic-level host interface to the single-wire LIN bus. It translates host-side command logic into the dominant/suppressed bus states and returns received bus levels as digital logic, with internal filtering and protection around the bus pin. Because only one transceiver channel is fitted, a node needing bidirectional LIN with separate transmit and receive paths should look at dual-channel members of the family. Typical applications include LIN slave nodes in body control modules, door and seat control units, ambient temperature and presence sensor nodes, climate control panel sub-nets, LIN-to-CAN gateway interfaces, and low-speed accessory modules where a robust, low-power single-wire link is preferred over CAN or RS-485. When designing with this transceiver, budget decoupling close to the supply pin and observe the LIN bus rise-time and slope requirements defined by ISO 17987-4; a node that must remain permanently listening for bus wake-up should be validated against the family's sleep and wake current figures before the PCB is frozen. This page brings together package and supply details, drop-in ordering variants within the same Infineon family, and practical interface design notes that are not reproduced from the manufacturer datasheet alone.
TLE7258SJXUMA1 - 20 kbps LIN Transceiver | Infineon
The Infineon TLE7258SJXUMA1 is an automotive LIN bus transceiver with a 20 kbps data rate, 5.5 V to 18 V supply range, and an 8-pin PG-DSO-8 package. It supports LIN 2.2A, ISO 17987-4, and SAE J2602-2 while combining the bus driver, receiver, integrated voltage regulator, wake-up support, and automotive protection features. A LIN transceiver is an interface IC that connects a microcontroller's serial data and control signals to the physical wiring of a Local Interconnect Network. Within the vehicle-network hierarchy, LIN is a low-cost, single-wire bus commonly used for non-critical body and comfort functions. The TLE7258SJXUMA1 forms the physical-layer boundary between the protocol controller and the LIN bus. Key features include operation up to 20 kbps, compatibility with LIN versions 1.2 through 2.2A, and a selectable 3.3 V or 5.0 V regulated output for the associated controller. The device supports low-power operating modes and enters standby after power-up until the microcontroller asserts the EN input. These characteristics suit distributed automotive modules that need reliable communication without a high-bandwidth network connection. The integrated voltage regulator reduces the external power-supply design required around the LIN transceiver. Wake-up and protection functions add system-level robustness for connected vehicle wiring, where transient energy and diagnostic bus activity must be handled close to the external connector. ISO 17987-4 compliance places the physical layer in a standardized automotive LIN framework, while SAE J2602-2 supports its use in the United States automotive market. Typical applications include door and window modules, HVAC controls, ambient lighting, seat controls, dashboard accessories, and body-control nodes. The device is particularly appropriate where a LIN subnet connects a low-cost microcontroller to switches, sensors, or actuators over a single vehicle wire. PCB design should preserve the transceiver's pin assignments, provide the required bus and supply decoupling specified by the manufacturer datasheet, and route the LIN connection to the protected connector. Confirm EMC, fault-tolerance, and wake-up behavior for the complete vehicle network rather than evaluating only nominal communication performance. This page combines manufacturer specifications, sourcing guidance, package details, and application-oriented engineering guidance to support LIN bus design, component selection, PCB implementation, and supply-chain planning.
TLE7259-2GU - 20 kbaud LIN Transceiver | Infineon
The Infineon TLE7259-2GU is a single-channel LIN transceiver for in-vehicle networks, operating from 7 V to 27 V with one driver and one receiver. It supports data rates from 2.4 kBaud to 20 kBaud according to the SAE J2602 standard and is packaged in an 8-pin SOIC, designated PG-DSO-8. A LIN transceiver is the physical-layer interface between a microcontroller or LIN protocol controller and the vehicle's LIN bus. The TLE7259-2GU converts controller-side serial signals into LIN bus levels, receives bus signals for the controller, and provides the electrical characteristics required by an in-vehicle network. It belongs to the broader hierarchy of interface IC, transceiver, communications transceiver, and automotive network interface. The TLE7259-2GU is a follow-up product to the TLE7259-2GE and provides the same functions and pin compatibility. Verified data identifies it as a full-duplex, single-transceiver device with a 10.4 kBaud listed data rate in distributor listings, while the manufacturer datasheet describes operation from 2.4 kBaud to 10.4 kBaud according to SAE J2602. The distinction matters because the TLE7259-2GU is specifically positioned for the stated LIN network range rather than a general-purpose CAN interface. The device is intended for automotive electronic control units, body modules, door modules, seat modules, lighting controllers, sensor interfaces, and other low-speed vehicle-network nodes. Its 8-pin SOIC package supports conventional surface-mount assembly, while the 7 V to 27 V supply range matches the verified component specification. The operating temperature range is listed as -40 C to 150 C in the verified GlobalSpecs data, making it relevant to automotive temperature environments. For PCB design, preserve the verified pin compatibility with the TLE7259-2GE and place the transceiver close to the LIN bus connection. The LIN bus requires an appropriate transceiver-level bus interface, protection strategy, and decoupling arrangement defined by the surrounding vehicle-network design. The TLE7259-2GU is a surface-mount SMD device in cut-reel packaging according to the verified source data. Use the manufacturer datasheet for exact pin names, application circuitry, electrical limits, and external-component recommendations before releasing a design. This product page combines verified specifications, source links, package information, and application context for engineers evaluating the TLE7259-2GU. It also distinguishes the TLE7259-2GU from merely functional interface alternatives and highlights the importance of confirming pin compatibility, supply range, protocol, and automotive requirements during substitution.
TLE7259-3LE - 20 kbps LIN Automotive Transceiver | Infineon
The Infineon TLE7259-3LE is an automotive LIN transceiver supporting data rates from 2.4 kbps to 20 kbps, with an 8 μA sleep current and integrated wake-up and protection features. It is designed for in-vehicle networks and operates from a 5.5 V to 27 V supply range in an 8-pin PG-TSON surface-mount package. A LIN transceiver, also called a Local Interconnect Network physical-layer interface, connects a vehicle’s protocol controller to the physical LIN bus. It combines a bus driver, receiver, wake-up logic, and protection functions into one device. In the vehicle electronics hierarchy, the TLE7259-3LE belongs to the interface-IC family and connects low-rate serial-control networks to modules such as door controls, seat controls, lighting modules, and body-control systems. The verified TLE7259-3 features include a 20 kbps maximum data rate, an 8 μA sleep current, and high EMC performance for LIN networks. Its integrated wake-up and protection features support low-power body-network operation and robust communication in electrically demanding vehicle environments. The 5.5 V to 27 V operating supply range allows use in conventional automotive electrical systems where transient and EMI conditions must be considered. The device provides a physical bus-driver interface between the LIN protocol controller and the LIN bus. At the protocol level, the host controller handles framing, addressing, and higher-layer messaging, while the transceiver translates digital controller signals into LIN bus levels and returns received bus information through RXD. The integrated protection and wake-up functions reduce the need for separate interface circuitry, although external network protection and layout practices still matter in production designs. Typical uses include LIN door modules, central locking, window and seat controls, ambient-lighting controllers, climate-control peripherals, body-control units, and other low-cost automotive subnetworks. The TLE7259-3LE is most appropriate when the design needs LIN communication between a low-rate embedded controller and distributed vehicle peripherals. For PCB implementation, place the transceiver near the LIN connector or bus routing point, keep the LIN trace short and isolated from sensitive analog and high-speed digital signals, and provide the external pull-up and bus capacitance required by the application. Verify sleep-current behavior, bus timing, wake-up polarity, EMC performance, and supply decoupling against the manufacturer datasheet. This page combines verified manufacturer specifications, sourcing context, application guidance, and drop-in-replacement analysis. It is intended to help engineers evaluate the TLE7259-3LE for automotive LIN designs while clearly separating verified values from information that still requires design-specific verification.
TLE72592GEXUMA1 - 20 kbaud LIN Transceiver | Infineon
The Infineon TLE72592GEXUMA1 is an automotive LIN bus transceiver for in-vehicle local interconnect networks, supporting data rates from 2.4 to 20 kBaud in an 8-pin SOIC-8 package. The device operates from a 5.5 V to 27 V supply and provides a 3.3 V or 5 V logic output. It integrates LIN wake-up and protection functions for compact, robust vehicle-network communication. A LIN transceiver is an interface IC that connects a low-cost serial bus used in vehicle body and comfort systems to a host microcontroller. Its hierarchy is LIN transceiver, automotive transceiver, interface IC, and semiconductor. The transceiver converts logic-level signals into the LIN bus waveform, receives bus data, and supports low-power wake-up behavior. This makes the device suitable for door modules, seat controls, climate controls, lighting, and other distributed automotive nodes. The TLE72592GEXUMA1 supports LIN 1.3 and LIN 2.x communication at rates up to 20 kBaud while maintaining a 5.5 V to 27 V supply range. Its 3.3 V or 5 V receive output allows connection to microcontrollers operating at either logic level. Integrated wake-up and protection features reduce external circuitry and improve suitability for electrically demanding automotive networks. The device combines a bus driver, receiver, and LIN-specific interface functions in one package. Its architecture is intended for unidirectional or bidirectional LIN communication in distributed vehicle systems. Compared with a general-purpose CAN or RS-232 interface, the TLE72592GEXUMA1 is designed specifically for LIN's single-wire topology, lower signaling rates, and automotive power environment. Typical uses include LIN-controlled vehicle body electronics, ambient lighting modules, powered seat and window controllers, climate-control panels, sensor interfaces, and gateway nodes. The 8-pin SOIC-8 format also supports conventional surface-mount assembly. Because LIN transceivers operate close to motor systems, relays, and other potentially noisy loads, correct bus termination, reference-ground implementation, and PCB layout remain essential. For a new design, verify the LIN controller voltage, wake-up polarity, transceiver mode, and bus capacitance against the manufacturer datasheet. Place the transceiver close to the LIN connector, keep the LIN route away from switching nodes and high-current paths, and use the prescribed pull-up and termination networks. The external component values and layout should follow the manufacturer's reference configuration. This product page organizes the key automotive LIN interface facts, replacement options, comparison parameters, and practical PCB guidance. It helps engineers evaluate the TLE72592GEXUMA1 as an 8-pin, 20 kbaud LIN transceiver before beginning a new vehicle-network design.
TLE72592GEXUMA4 - 20 kBaud LIN Transceiver | Infineon
Infineon Technologies TLE72592GEXUMA4 is a half-duplex Local Interconnect Network transceiver with one transmitter and one receiver, supporting data rates from 2.4 kBaud to 20 kBaud. The device is packaged in an 8-pin PG-DSO-8-16 surface-mount package, and its operating temperature range extends from -40°C to 150°C. A LIN transceiver is an interface IC that connects a microcontroller or other host controller to a low-cost, single-wire automotive network. It converts serial logic-level commands into the electrical signaling used on the LIN bus and receives bus activity back into the host. The TLE7259-2GE family also integrates wake-up and protection functions for use in in-vehicle networks. The TLE72592GEXUMA4 provides a maximum LIN data rate of 20 kBaud and a minimum supported rate of 2.4 kBaud. Its 1-transmitter, 1-receiver arrangement supports half-duplex communication, with the transmitter and receiver sharing access to the LIN conductor. The listed receiver hysteresis is 300 mV, a parameter involved in determining the noise margin for received bus signals. The device operates from a 7 V to 27 V supply, allowing it to interface with conventional automotive electrical systems. Its PG-DSO-8-16 package has eight terminals, a gull-wing surface-mount form, and a maximum seated height of 1.73 mm. The listed moisture sensitivity classification is MSL 2A for a four-week floor-life period, which requires controlled handling and appropriate soldering practices. Typical applications include LIN-connected vehicle body-control modules, door and seat controllers, climate-control interfaces, lighting controllers, sensor gateways, and other automotive electronic nodes. The 2.4 kBaud to 20 kBaud range covers common LIN communication tasks involving switches, actuators, and simple sensors. When designing the LIN node, verify that the host controller logic levels, transceiver supply, ground reference, bus termination, and wake-up configuration match the vehicle network architecture. Place the transceiver close to the LIN connector and route the bus conductor away from high-current switching paths to reduce coupling into this low-speed, single-wire network. This page combines the manufacturer's LIN transceiver characteristics with package, environmental, application, and replacement guidance. It also distinguishes exact drop-in candidates from broader LIN interface options so engineers can assess footprint, communication-rate, and protection considerations before changing an automotive design.
TLE72593GEXUMA1 - LIN Transceiver 20 kBaud | Infineon
The Infineon Technologies TLE72593GEXUMA1 is an automotive LIN bus transceiver with one transmitter and one receiver, supporting data rates from 2.4 kBaud to 20 kBaud. It is supplied in the PG-DSO-8-16 surface-mount package and is designed for in-vehicle network communication with integrated wake-up and protection features. The device is identified as a half LIN bus transceiver, providing the physical-layer interface between a vehicle LIN network and a host controller. A LIN transceiver is a physical-layer interface IC used in automotive serial networks. LIN, or Local Interconnect Network, is a low-cost, single-wire vehicle bus used to connect relatively simple sensors and actuators with an electronic control unit. The transceiver translates logic-level data into the LIN bus signal on transmission and converts received bus levels into a logic-level signal for the host microcontroller. The TLE72593GEXUMA1 therefore belongs to the interface IC and automotive network transceiver hierarchy, providing the connection between a microcontroller UART or LIN-capable controller and the vehicle network. The TLE7259-3GE family is specified for 20 kBaud LIN operation, with integrated wake-up functionality and protection features. The manufacturer describes the device as intended for in-vehicle networks and lists an operating range up to 150 degrees Celsius in the product comparison material. The one-transmitter, one-receiver arrangement supports point-to-point or node communication arrangements where a single bus transceiver is required. Its PG-DSO-8-16 package supports surface-mount PCB assembly in compact automotive electronic modules. The integrated wake-up function is useful when the vehicle network must transition from a low-power state after a bus activity event. Protection features are important because LIN buses connect external wiring and equipment that can expose the transceiver to automotive electrical transients. The device should therefore be evaluated together with the vehicle's line-network protection strategy, supply-behind-configuration requirements, grounding arrangement, and the host controller's LIN framing and baud-rate configuration. Typical applications include body-control modules, seat and door modules, climate-control submodules, lighting controllers, sensor interfaces, seat-comfort systems, and other automotive electronic control units that use LIN subnets. The part is most appropriate when the design needs a low-speed LIN physical-layer interface, automotive-oriented protection, and a compact surface-mount package rather than a high-bandwidth communication solution. When designing the circuit, confirm the device's pin assignment, supply range, transceiver operating mode, and external line-network recommendations in the manufacturer datasheet. Place the transceiver and its required input, output, and protection components close to the connector and controller interface, while keeping the LIN wiring path physically separated from sensitive analog and high-speed digital circuits. Validate wake-up behavior and fault recovery across the complete vehicle power sequence. This product page combines the identified LIN transceiver specifications, package information, protection and wake-up features, application context, drop-in alternatives, and practical design guidance for engineers evaluating the TLE72593GEXUMA1 in automotive electronic systems.
TLE72593GEXUMA3 - 20 kbps LIN Transceiver | Infineon
Infineon Technologies TLE72593GEXUMA3 is an automotive LIN bus transceiver with one transmitter and one receiver, supporting data rates to 20 kbps in an 8-pin PG-DSO-8-16 surface-mount package. The device integrates the LIN transceiver with a 5.5 V regulator, operates from a 5.5 V to 27 V supply range, and is designed for 3.3 V and 5 V microcontroller interfaces. According to the Infineon product documentation, it complies with ISO 17987-4 and LIN Specification 2.2A. A LIN transceiver, or Local Interconnect Network transceiver, is a physical-layer interface IC that connects a controller-side logic device to a single-wire vehicle network. LIN belongs to the broader automotive network-interface hierarchy and provides a comparatively simple communications method for distributed switches, lamps, sensors, seat modules, and body-control nodes. The TLE72593GEXUMA3 translates logic-level TxD and RxD signals into the LIN bus waveform while providing bus dominance, receive hysteresis, fault protection, and low-power sleep behavior. Key features include a maximum LIN data rate of 20 kbps, very low sleep-mode current, and very low leakage on the BUS pin. The receiver uses approximately 120 mV hysteresis to improve decision margin in noisy automotive environments, while the listed early-warning detection value is 99%. The TxD input includes dominant-state timeout protection. Digital input and output levels support both 3.3 V and 5 V microcontrollers, making the interface suitable for mixed-voltage control modules. The TLE7259-3 family is designed for automotive networks and provides an ESD withstand rating of ±15 kV according to the manufacturer datasheet. Its PG-DSO-8-16 package supports compact surface-mount layouts, and the integrated voltage regulator reduces the number of external power components. The device is identified as AEC-Q100 automotive-qualified and is specified for an operating temperature range of −40°C to +150°C. Typical applications include LIN-controlled vehicle body systems, door modules, mirror controllers, ambient-light and climate-control nodes, sensor interfaces, and seat-control modules. LIN is particularly useful where wiring cost and implementation complexity are more important than maximum bandwidth. This device is also appropriate for 3.3 V or 5 V MCU-based control units that need standardized LIN physical-layer behavior and automotive transient protection. Design the external bus network with an appropriate pull-up resistor and the voltage-regulator output and transceiver supply pins decoupled close to the package. Confirm that the MCU supply domain matches the transceiver's logic-level compatibility, and verify the LIN node's sleep and wake behavior during power-state transitions. The integrated regulator reduces board complexity, but its load capability and thermal margin must still be checked against the complete module budget. This page combines exact manufacturer and distributor attributes with practical interface guidance, package constraints, application fit, and verified same-family drop-in options. It also highlights where an engineering review is required before treating a substitute as a direct replacement, particularly for regulator-output behavior, wake logic, and protection thresholds.
TLE72593LEXUMA1 - 20kbps LIN Transceiver | Infineon Technologies
The Infineon Technologies TLE72593LEXUMA1 is a LIN bus transceiver for in-vehicle communication systems, supporting data rates from 2.4 kbps to 20 kbps in an 8-pin PG-TSON-8-1 package. It operates from a 5.5 V to 27 V supply and includes a LIN bus driver, receiver, integrated wake-up capability, and protection features for robust connection to a Local Interconnect Network. A LIN transceiver, also called a LIN interface or physical-layer transceiver, is an interface IC that converts logic-level signals from a LIN protocol controller into physical bus signals and converts incoming bus activity back into controller-compatible signals. Within the automotive electronics hierarchy, a LIN transceiver is a communications transceiver, an interface IC, and a semiconductor used in vehicle body and comfort electronics. The TLE7259-3 supports LIN standards and data rates from 2.4 kbps to 20 kbps. Its integrated wake-up functions allow the network node to detect remote LIN bus traffic or a local wake-up signal. The INH output provides an additional control signal for external circuitry such as a voltage regulator. According to the manufacturer information, Sleep-mode quiescent current is typically below 8 microamperes, while the BUS input uses very low leakage current. The device functions as the physical bus driver between a LIN protocol controller and the LIN wiring harness. This division of responsibility keeps waveform generation, bus-level detection, wake-up handling, and fault protection within a dedicated interface IC. The resulting architecture is suitable for distributed vehicle networks in which multiple low-cost nodes exchange small control messages over a single-wire bus. Typical uses include door modules, seat controls, window and mirror switches, climate-control panels, body-control modules, ambient lighting controls, and other LIN sub-networks. Its wide operating supply range supports automotive electrical environments, while the 20 kbps limit fits conventional LIN communication rather than high-speed automotive Ethernet or other high-bandwidth vehicle networks. For implementation, use the manufacturer pin-description and application information to assign LIN, supply, ground, enable, wake-up, and INH functions. Place the transceiver and its supporting components close to the connector or bus branch, maintain the required input and output capacitors, and follow the recommended bus termination and layout guidance to reduce radiated noise and susceptibility to interference. This product overview combines the device's verified operating limits and automotive features with practical guidance on LIN integration, low-power operation, protection, and design trade-offs. It is intended to help engineers evaluate bus compatibility, package constraints, wake-up behavior, and replacement decisions before committing a PCB design.
TLE7259G - 20 kBaud LIN Transceiver | Infineon | Automotive
The Infineon Technologies TLE7259G is an automotive LIN transceiver supporting data rates from 2.4 kBaud to 20 kBaud, with a specified 3.5 V to 5.5 V operating range, integrated wake-up functionality, and integrated protection features. It is packaged in an 8-pin SOIC and is intended for Local Interconnect Network nodes in in-vehicle communication systems. The verified source identifies the TLE7259G as a LIN transceiver, while several detailed electrical limits and pin assignments remain unavailable in the supplied data. A LIN transceiver is an interface IC that connects a microcontroller UART to a LIN bus. LIN, or Local Interconnect Network, is a low-cost, single-wire vehicle network commonly used for sensors, actuators, body electronics, and comfort systems. The transceiver translates logic-level signals between the host controller and the LIN physical bus, while wake-up and protection functions support reliable operation in electrically harsh environments. Its 20 kBaud maximum rate matches the source description for in-vehicle LIN networks. The key verified characteristics are the 2.4 kBaud-to-20 kBaud data-rate range, 3.5 V-to-5.5 V supply range, integrated wake-up, integrated protection, and 8-pin SOIC construction. These features make the device applicable to distributed vehicle nodes where a host MCU requires a standardized LIN physical layer. The source does not provide verified values for transceiver mode, sleep current, bus thresholds, propagation delay, ESD rating, or absolute maximum ratings, so those parameters are not inferred here. TLE7259G is most relevant to body and comfort modules, sensor interfaces, actuator controllers, door and window modules, climate-control systems, and other LIN subnets. The host microcontroller handles LIN frame generation and protocol timing; the transceiver supplies the physical-layer connection. Designers must confirm the complete LIN electrical specification, pinout, external components, supply sequencing, and protection requirements against the manufacturer datasheet before production release. For PCB implementation, place the transceiver close to the LIN bus connection and route the single-wire bus away from sensitive analog and high-speed digital signals. The LIN bus requires an appropriate pull-up arrangement and protection strategy; exact resistor and protection values should follow the verified datasheet and system-level EMC requirements. Keep the supply and ground return paths short, and verify the device's wake-up behavior in the intended low-power architecture. This page combines the verified TLE7259G source descriptions, pricing references, package information, and cross-reference findings with engineering selection context. The supplied data does not establish enough verified information to populate every electrical specification, complete pinout, lifecycle classification, or qualified drop-in alternative without risking an inaccurate replacement recommendation.
TLE7259GNT - 20kBd LIN Transceiver, P-DSO-8 | Infineon
Infineon Technologies TLE7259GNT is an automotive-grade LIN bus transceiver operating at 20 kBd in an 8-pin P-DSO-8 surface-mount package. Verified distributor data identifies a 1/1 transceiver arrangement, full LIN-bus operation, an 8-terminal gull-wing package, and an operating-temperature range of -40°C to 150°C. The device belongs to the LIN interface-transceiver category and converts between a host controller's logic-level UART signals and the physical LIN network. Its principal electrical values, including supply voltage limits, receiver hysteresis, output-driver details, and sleep or wake behavior, were not included in the supplied verified records and therefore require confirmation from the manufacturer datasheet before design release. The public parts database labels TLE7259GNT obsolete or end-of-life, although distributor listings remain available. Engineers should treat lifecycle status, stock, and sourcing conditions as time-sensitive rather than assuming broad future availability. TLE7259GNT is associated with automotive LIN subnets, body electronics, climate controls, seat modules, door modules, lighting controllers, and sensor gateways where a standardized low-speed serial bus connects distributed nodes. Its 20 kBd LIN rate is suitable for control and status traffic rather than high-bandwidth payloads. The package keeps the physical implementation compact, but successful deployment still depends on correct transceiver pin mapping, bus termination, reference-ground handling, ESD protection, decoupling, and compliance with the LIN network requirements used by the vehicle platform. This page summarizes verified distributor and database records, available sourcing information, documented package and protocol details, and the unresolved datasheet parameters that must be checked before substitution or PCB release.
TLE7259GT - 20 kBd LIN Transceiver | Infineon | Automotive
The Infineon TLE7259GT is a half-duplex LIN bus transceiver with one transmitter and one receiver, a 7 V to 27 V supply range, and a maximum transmission rate of 20 kBaud. The device is packaged for surface-mount assembly in an 8-pin DSO/SOIC-style package and is supplied in tape-and-reel packaging. It complies with LIN specification versions 1.3, 2.0, and 2.1, while also supporting the ISO 9141 K-line function. A LIN transceiver is an interface IC that connects a host microcontroller to a low-cost, single-wire automotive communication bus. LIN belongs to the broader CAN and automotive-network hierarchy: a CAN bus is a high-speed, multi-node network, while LIN uses a slower serial protocol optimized for cost-sensitive distributed vehicle subsystems. The TLE7259GT converts logic-level requests from a controller into LIN-bus signals and converts received bus levels into logic signals for the controller. The TLE7259GT supports transmission rates through 20 kBaud and includes LIN specification compatibility for versions 1.3, 2.0, and 2.1. Its 7 V to 27 V operating supply range accommodates vehicle battery environments. Additional cited features include K-line support under ISO 9141, very high ESD robustness, and very low electromagnetic emission. These characteristics make the device relevant to LIN nodes requiring protocol compatibility and strong protection against conducted or capacitive bus disturbances. Technically, the device combines a bus-side transmitter and receiver with the interface needed for an embedded host. A microcontroller can control bus dominance, monitor received frames, detect communication errors, and implement LIN scheduling. Because LIN commonly operates from a vehicle supply, the 27 V maximum operating voltage provides additional margin relative to 5 V transceiver packages, although the final design must still account for load dump and transient requirements at the wiring interface. Typical applications include body-control modules, door and seat controllers, climate-control panels, lighting controllers, automotive gateways, and other distributed electrical subsystems. The K-line function broadens its utility in diagnostic or legacy vehicle interfaces, while the 20 kBaud rate matches common LIN physical-layer implementations. Designers should verify bus termination, supply decoupling, transceiver sleep behavior, and protection requirements against the manufacturer datasheet before layout release. The LIN bus wiring is sensitive to ground offsets, capacitance, reflections, and ESD events, so PCB placement and vehicle harness design remain as important as the nominal IC specification. This product page consolidates verified specifications, sourcing context, application guidance, and strict drop-in replacement criteria. Where the supplied web evidence does not establish a complete pin map, pricing schedule, or lifecycle designation, those details remain explicitly unverified rather than being inferred.
TLE7263E - Integrated CAN, LIN and LDO SBC | Infineon
The Infineon Technologies TLE7263E is an integrated HS-CAN, LIN, low-dropout regulator, and high-side switch system basis chip rated for a 13.5 V supply, housed in a PG-DSO-36-24 package. It provides a 5 V output rated at 150 mA, a standard 16-bit SPI interface, controller stop-mode support, and a 50 µA sleep mode. The integrated LIN transceiver includes a 30 kΩ pull-up resistor for fail-safe operation. A system basis chip is an automotive power and communication component that consolidates supply regulation, high-side switching, diagnostic interfaces, and network transceivers. In the hierarchy, this TLE7263E combines a LIN transceiver, high-speed CAN interface, two low-dropout voltage regulators, and a high-side switch to support centralized electrical architecture and body or comfort-system electronics. The principal verified features include compatibility with the LIN 2.0 specification and ISO 9141, a 13.5 V supply configuration, a 1 mA supply-current figure reported by a distributor index, and two integrated low-dropout regulators. The 16-bit SPI interface allows a host microcontroller to configure and monitor the system basis functions, while stop and sleep modes support reduced-power operating states. The TLE7263E consolidates several discrete automotive functions into one IC, reducing PCB area and the number of external network-interface components. Its 150 mA, 5 V regulator capability is suitable for low-power automotive loads, although it is not intended to power loads whose current exceeds that rating. The exposed-pad package also requires attention to PCB thermal design and copper placement. Typical uses include automotive body-control modules, door and seat controllers, climate-control electronics, lighting-control units, LIN-connected actuators, gateways combining LIN and CAN, and other low-voltage vehicle electronics. Designers should verify transceiver limits, regulator startup behavior, pin electrical limits, and watchdog operation directly against the manufacturer datasheet before production release. For layout, place the device close to protected vehicle-power entry, route high-current switched paths with adequate copper, and keep sensitive CAN and LIN nodes compact and isolated from switching edges. Confirm startup sequencing, diagnostic behavior, watchdog timing, and sleep-mode current in the target ECU environment. This page combines verified manufacturer-linked specifications, distributor package information, application guidance, and replacement-policy checks. It does not claim an unqualified drop-in alternative because the supplied cross-reference results did not verify five pin-compatible parts.
TLE7263EXUMA2 - Integrated CAN, LIN, LDO and Switch | Infineon
The Infineon TLE7263EXUMA2 is an integrated body-system interface IC combining a high-speed CAN transceiver, a LIN transceiver, dual low-dropout regulators for an external 5 V supply, a high-side switch, a 16-bit SPI control and monitoring interface, a window watchdog, reset, and fail-safe functions in a 36-pin PG-DSO package. The verified distributor information identifies the device as a specialized CAN interface IC and gives a nominal supply voltage of 13.5 V. An automotive body interface IC coordinates communication, regulation, switching, and diagnostics between a vehicle controller and distributed sensors or actuators. This integration reduces the number of discrete interface components, centralizes configuration and monitoring, and simplifies PCB routing. In the TLE7263EXUMA2, CAN and LIN provide vehicle-network connectivity, while the dual LDO block and high-side switch support external loads and power distribution. The principal verified functions are an HS-CAN transceiver, a LIN transceiver, dual 5 V LDO capability, a high-side switch, and a 16-bit SPI control port. The SPI interface allows a host microcontroller to configure the device and obtain status information. A window watchdog with reset and a fail-safe output support dependable recovery and controlled operation when the vehicle network or host controller becomes unresponsive. The device is supplied in a 36-pin PG-DSO surface-mount package and operates from a nominal 13.5 V supply according to the verified product listings. This makes it relevant to distributed automotive body electronics, including door and body-control modules, gate modules, seat-control electronics, climate-control interfaces, lighting controllers, and gateway equipment that connects CAN and LIN networks. Power and signal layout are critical in an automotive environment. Keep the supply and ground connections short, provide the decoupling capacitors recommended by the manufacturer datasheet, and route transceiver and SPI signals away from noisy switching nodes. Because the verified data does not provide exact regulator ratings, timing limits, transceiver thresholds, or the complete pin assignment, those values must be confirmed in the manufacturer datasheet before schematic release or PCB sign-off. This page consolidates verified distributor pricing, product-function details, application context, and procurement guidance with datasheet links. It also distinguishes confirmed specifications from unavailable parameters, helping engineers evaluate the TLE7263EXUMA2 without relying on unverified substitute claims or assumed pin compatibility.
TLE7268LCXUMA1 - Dual 20 kbps LIN Transceiver | Infineon
Infineon Technologies TLE7268LCXUMA1 is a dual LIN 2.2 automotive transceiver with two independent single-wire LIN channels, a maximum transmission rate of 20 kbps, and a PG-TSON-14-3 leadless package. It is designed for LIN vehicle-network nodes requiring ISO 17987-4, LIN Specification 2.2 A, and SAE J2602 compliance. The integrated pair of transceivers supports 3.3 V and 5 V digital I/O levels, low sleep-mode current consumption, wake-up capability, and very low leakage on the BUSx pins. A LIN transceiver is an interface integrated circuit that connects a microcontroller or body-controller module to a single-wire automotive network bus. In the broader hierarchy, a LIN transceiver is a wired-network transceiver, an interface IC, and ultimately a semiconductor. It converts controller-level transmit and receive signals into the voltage levels required by LIN buses and provides bus protection, fault detection, sleep behavior, and wake-up functions needed in distributed vehicle electronics. The TLE7268LCXUMA1 combines two independent LIN transceivers in one device. Each channel supports communication at up to 20 kbps and operates with 3.3 V or 5 V digital I/O levels. Its sleep mode reduces standby consumption, while wake-up capability allows a node to respond to bus activity. Very low BUSx leakage is valuable when multiple modules share a vehicle network because it reduces unintended loading and helps preserve the integrity of bus communication. The device is compliant with ISO 17987-4, LIN Specification 2.2 A, and SAE J2602. These standards are specifically identified in the manufacturer datasheet for the TLE7268 family. The PG-TSON-14-3 package supports compact automotive circuit-board layouts and includes lead-tip inspection support according to the supplied component references, enabling automated optical inspection during production. Detailed electrical limits, pin names, ESD ratings, temperature limits, and timing values are not present in the verified excerpts and therefore remain marked as data needed rather than being inferred. Typical uses include body-control modules, gateways, seat and door controllers, climate-control electronics, lighting controllers, and other automotive nodes that require two LIN channels. Using two transceivers in one package can simplify board partitioning when a controller communicates with two independent LIN subnets. Designers must still account for the device's 20 kbps maximum rate, digital-interface supply compatibility, sleep and wake configuration, bus termination, external microcontroller I/O, and automotive ESD requirements. The principal design consideration is that two LIN channels do not create two independent power-management domains. Their supply, ground, enable, and common-mode implementation must follow the complete TLE7268LC datasheet. Verify pin assignments, exposed-pad requirements, bus network topology, and automotive qualification details for the exact ordered variant before releasing a production PCB. This product record consolidates the verified manufacturer and distributor information, package characteristics, standards coverage, technical FAQs, and selection guidance. It also clearly distinguishes documented specifications from parameters that still require confirmation, helping engineers evaluate the dual-LIN interface without relying on unverified substitute parts or fabricated electrical data.
TLE7268SKXUMA1 - Dual 20 kbps LIN Transceiver | Infineon
Infineon Technologies TLE7268SKXUMA1 is an automotive dual LIN 2.2 transceiver that integrates two independent single-wire LIN transceivers in one PG-DSO-14 package. Each channel supports transmission rates up to 20 kbps, and the device is compliant with ISO 17987-4, LIN Specification 2.2 A, and SAE J2602. Its integrated interfaces are designed for 3.3 V and 5 V digital I/O levels, allowing connection to automotive body controllers, gateways, and other LIN nodes. The TLE7268SKXUMA1 also provides very low Sleep-mode current consumption with wake-up capability and very low leakage on the BUSx pins. A LIN transceiver, short for Local Interconnect Network transceiver, is an interface IC that connects a microcontroller or body-control module to a LIN bus. LIN is a low-cost, single-wire automotive network derived from the CAN concept but optimized for slower communication, lower wiring complexity, and cost-sensitive vehicle subsystems. In the component hierarchy, the TLE7268SKXUMA1 is a LIN transceiver, then an automotive interface IC, then an interface semiconductor. Key features include two independently usable LIN channels, operation to 20 kbps, compatibility with 3.3 V and 5 V digital logic, low Sleep-mode consumption, and wake-up capability. Compliance with ISO 17987-4, LIN Specification 2.2 A, and SAE J2602 supports integration into modern automotive communication systems. Very low BUSx leakage helps prevent unwanted bus loading and supports predictable behavior when connected LIN nodes enter low-power states. The device provides the physical-layer interface between the host controller and each LIN bus. Its digital transmit and receive pins connect to a microcontroller, while BUS1 and BUS2 connect to the LIN network. The independent-channel architecture allows one transceiver package to serve two LIN networks, reducing component count and PCB area compared with two separate single-channel LIN transceivers. External implementation details, including bus termination, wake-up wiring, and logic pull-ups, must follow the manufacturer datasheet. Typical uses include body-control modules, automotive gateways, seat and door modules, climate-control units, sensor nodes, and other ECUs connected by LIN sub-buses. Because the TLE7268SKXUMA1 supports two channels, it is especially useful where one ECU must interface with two separate LIN networks or where a gateway bridges multiple vehicle subsystems. For PCB implementation, preserve the package-specific land pattern, place the transceiver close to the LIN connector or bus routing, and keep BUS traces away from sensitive high-speed signals. Decoupling and signal-integrity values are not specified in the supplied verified excerpts, so component selection and layout must be completed against the complete manufacturer datasheet. This page consolidates verified manufacturer and distributor information, compliance statements, pricing status, and engineering guidance for the TLE7268SKXUMA1. It also distinguishes verified dual-LIN functionality from unavailable electrical details, preventing unsupported assumptions about pinout, thermal limits, or substitute compatibility.
TLE7269G - Dual LIN Transceiver, 20 kBaud | Infineon
Infineon Technologies TLE7269G is a LIN 2.1-compliant dual LIN transceiver supporting data rates from 2.4 kBaud to 20 kBaud for in-vehicle networks. The device integrates wake-up and protection functions and is optimized for low electromagnetic interference and a sleep-mode current below 10 mA. It is supplied in a 14-pin PG-DSO package, also identified as PG-DSO-14-24 in distributor listings. A LIN transceiver, also called a LIN bus interface, belongs to the vehicle-network interface IC hierarchy and connects a microcontroller or cluster ECU to a low-speed serial network. It converts logic-level transmit and receive signals into physical LIN bus signals, while recovering incoming data for the host controller. The TLE7269G combines two LIN channels in one package, reducing board area where multiple vehicle subnets or redundant communication links are required. Key features include dual-channel operation, LIN 2.1 compliance, integrated wake-up capability, protection features, low EMI, and a sleep-mode current below 10 mA. Its data-rate range of 2.4 kBaud to 20 kBaud matches the operating range cited in the manufacturer datasheet. The very low leakage current on the bus pins also supports partially supplied LIN networks, helping nodes that remain unpowered avoid loading the active network. The TLE7269G is based on Infineon Smart Power Technology SPT, according to the manufacturer datasheet. This process combines digital control functions with automotive-grade power and interface robustness. The manufacturer specifically highlights excellent ESD robustness and high electromagnetic immunity, both important in vehicle electrical environments where cable-borne transients and radio-frequency coupling can disrupt low-speed communication. Typical uses include body-control modules, door and seat controllers, climate-control panels, lighting controllers, seat and door modules, and other ECUs connected through LIN subnets. The dual-channel configuration is particularly useful when an ECU needs two independent LIN endpoints or participates in more than one vehicle network segment. When designing around the TLE7269G, preserve the recommended external resistor, capacitor, and bus-termination arrangements from the manufacturer datasheet. Keep the LIN bus route away from sensitive analog signals and provide the required pull-up and wake-up components to avoid excessive bus loading. The low sleep current and bus leakage support low-power designs, but functional sleep and wake behavior must still be verified against the complete network topology. This page combines verified manufacturer and distributor facts with a focused comparison of the most relevant substitute candidates, application guidance, and practical interface-design notes. It distinguishes published characteristics from parameters that still require direct confirmation for a specific ordering code or design revision.
TLE7269GXUMA1 - 20 kBaud Dual LIN Transceiver | Infineon
The Infineon TLE7269GXUMA1 is a dual-channel Local Interconnect Network transceiver that supports LIN communication at up to 20 kBaud and is supplied in a 14-pin PG-DSO-24 automotive package. It combines two stand-alone LIN transceivers in one device, reducing the component count for multi-LIN automotive electronic control units. The device supports LIN 1.3, LIN 2.0, and LIN 2.1 operation and is compliant with SAE J2602. A LIN transceiver is an automotive interface IC that converts logic-level controller signals into the physical LIN bus waveform and receives bus data for recovery by a microcontroller or LIN-capable communication controller. LIN belongs to the vehicle network hierarchy rather than high-speed Ethernet or CAN networks. It provides a cost-effective single-wire bus for distributed body, comfort, seat, door, lighting, and sensor modules. The TLE7269GXUMA1 provides two independent stand-alone LIN transceivers with a maximum transmission rate of 20 kBaud. Its LIN 2.0 and LIN 2.1 compliance, together with SAE J2602 compliance, makes it appropriate for modern vehicle electrical systems. The device is pin compatible with single LIN transceivers such as the TLE7259-2GE and TLE7259-GU, allowing integration of two LIN channels while preserving familiar transceiver connections. Electrical robustness is a major design consideration for vehicle wiring harnesses. The TLE7269GXUMA1 provides very high ESD robustness rated at 8 kV according to IEC 61000-4-2. This protection helps improve tolerance of direct and indirect ESD events encountered during vehicle assembly, servicing, and operation. The device is also optimized for low electromagnetic emission and high immunity against electromagnetic interference, supporting stable operation in electrically noisy automotive environments. Typical uses include body-control modules, door and seat controllers, climate-control electronics, lighting controllers, gateway modules, and other ECUs that require two LIN ports. Each transceiver can interface a local microcontroller with a physical LIN network bus, while low electromagnetic emission helps reduce interference with nearby sensitive electronics. Designers should verify transceiver enable, sleep, wake-up, supply-voltage, and bus-line details against the manufacturer datasheet before layout. The automotive 14-terminal DSO package also requires adequate board area, pin-1 orientation, and production-quality assembly controls. Access to the detailed pin table was not present in the supplied source excerpts, so pin-level assignment should not be inferred from the package drawing alone. This product page consolidates verified LIN capabilities, package information, ESD rating, compliance claims, distributor availability, and design considerations. It also distinguishes confirmed drop-in alternatives from unverified substitutes so engineers can make evidence-based sourcing and design decisions without relying on assumptions.
TLE7269GXUMA3 - Dual 20 kbaud LIN Transceiver | Infineon
Infineon Technologies TLE7269GXUMA3 is an automotive twin LIN transceiver IC with two independent LIN bus channels, a maximum transmission rate of 20 kbaud, and a 14-terminal PG-DSO-14-62 surface-mount package. According to the verified manufacturer-related search data, the device is compliant with LIN specifications 1.3, 2.0, and 2.1 as well as SAE J2602. It is pin compatible with single-channel LIN transceivers such as TLE7259-2GE and TLE7259-2GU, which supports board-level standardization when channel count and application requirements permit. A LIN transceiver is an interface integrated circuit that connects a microcontroller or other host to a low-speed serial network. LIN, meaning Local Interconnect Network, is a lower-cost vehicle-network architecture typically used for sensors, actuators, door modules, climate controls, and other distributed body-electronics functions. The broader hierarchy is LIN transceiver → automotive serial interface → interface IC → integrated circuit, with the transceiver handling physical-layer communication rather than application protocols or host processing. The TLE7269GXUMA3 provides two stand-alone LIN channels, allowing one device to connect two LIN networks or two physical segments. Its supported data rate of up to 20 kbaud aligns with conventional LIN communication rates. The verified data also identifies 8 kV ESD robustness according to IEC 61000-4-2, optimized electromagnetic emission, and high immunity against interference. These characteristics are particularly relevant in automotive environments where cable routing, nearby powertrain systems, and external body connectors can expose the network to electrostatic discharge and electromagnetic coupling. The part is described as an AEC-Q100 automotive LIN transceiver in a PG-DSO-14-62 package. The available distributor records identify a two-channel, full LIN-bus transceiver configuration with gull-wing leads and automotive temperature grade. The verified sources do not provide the complete electrical limit table, so details such as supply voltage, receiver thresholds, TXD logic levels, sleep-current consumption, and exact thermal limits must be confirmed in the manufacturer datasheet before schematic release or production qualification. Typical uses include automotive body-domain modules, door and seat controllers, climate-control gateways, sensor nodes, ambient-lighting controllers, and LIN-to-CAN or LIN-to-MCU interface boards. The twin-channel arrangement can reduce component count when two independent LIN segments are required, although channel-specific enable, sleep, wake-up, and fault-management behavior must be verified in the full datasheet. PCB design should preserve the LIN transceiver's automotive ESD and EMC performance. Keep the LIN bus and ground-return paths appropriately coupled, minimize loop area, follow the manufacturer's application-circuit layout, and provide verified supply and input-decoupling networks. Do not infer external protection-component values or bus termination details from search snippets; use the complete manufacturer datasheet and reference application guidance. This page consolidates verified distributor listings, LIN standards support, automotive qualification information, package details, and practical sourcing guidance. It also distinguishes confirmed facts from unavailable specifications and avoids presenting unverified substitute parts as drop-in replacements.
TLE7729TXUMA1 - 4-Channel Airbag Receiver | Infineon
The Infineon Technologies TLE7729TXUMA1 is a four-channel airbag satellite receiver IC using the company’s SatRIC serial interface architecture. It is designed for automotive occupant-protection systems in which remote satellite sensors report acceleration and crash-relevant measurements to a central airbag control module. The device is offered in a 28-pin PG-TSSOP surface-mount package and is supplied in tape-and-reel packaging. An interface IC is an integrated circuit that connects sensors, controllers, and other system blocks using standardized electrical signaling. Within the automotive electronics hierarchy, the TLE7729TXUMA1 belongs to the specialized interface IC category rather than a general-purpose communications transceiver. Its defining role is to receive information from multiple remote sensing nodes and forward it to the vehicle safety controller over a serial interface, reducing the number of separate wiring connections required by a distributed restraint system. According to the available TLE7729 documentation, the principal identified functions are four-channel satellite reception, SatRIC operation, and a serial interface for automotive airbag systems. The automotive qualification designation and specialized SatRIC architecture make the IC suitable only where the surrounding sensing, bus, and restraint-control architecture is compatible with Infineon’s system. It should not be treated as a general-purpose UART, SPI, or CAN transceiver because the verified sources describe a dedicated satellite-receiver application. The verified component information identifies the package as PG-TSSOP-28, also described by distributors as a 28-pin TSSOP. Tape-and-reel ordering is indicated by the TXUMA1 ordering code and by distributor listings that identify the part as 28TSSOP T/R. Because the retrieved sources do not expose individual terminal names or a complete pin-assignment table, the package diagram is identified separately from the electrical pin map. Typical uses include distributed airbag satellite sensors, remote acceleration-sensing modules in vehicle restraint systems, and central airbag control units that collect crash data from several remote sensor locations. The four-channel architecture supports multi-axis sensing systems by consolidating several satellite signals behind a dedicated serial receiver. The critical design constraint is system-level interoperability. A PCB redesign should preserve the Infineon-defined SatRIC physical interface, power distribution, reference connections, and communication timing because no verified evidence in the supplied data confirms that an unrelated generic interface IC is pin-to-pin compatible. Vehicle-level EMC behavior, diagnostic coverage, and air-quality or functional-safety conclusions should be validated against the complete manufacturer datasheet and the deployment platform rather than inferred from distributor summaries.