集成电路

子分类

📁 ADC/DAC 2,700+ 产品 📁 放大器IC 1,100+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 480+ 产品 📁 Comparator ICs 0 产品 📁 DSP 1,000+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6,800+ 产品 📁 接口IC 2,300+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 360+ 产品 📁 存储IC 870+ 产品 📁 微控制器 19,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（35,000+)

PIC16LF1705-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip
PIC16LF1705-I/P

PIC16LF1705-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF1705-I/P is a cost-effective 8-bit PIC microcontroller featuring a RISC CPU core operating at up to 32MHz, housed in a 14-pin PDIP (0.300 inch, 7.62mm) through-hole package. It integrates 14KB (8K x 14) of self-programmable Flash program memory, 1KB of SRAM data memory, and 128 bytes of data EEPROM, providing a balanced mix of code space and persistent storage for embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (typically Flash), data RAM, peripherals (timers, ADC, communications), and I/O on one die. The PIC16 family uses Microchip's enhanced mid-range 8-bit RISC architecture and falls within the hierarchy: MCU -> 8-bit MCU -> PIC microcontroller -> PIC16 family -> PIC16F/LF170x series. The 'LF' suffix indicates a wide-voltage low-power variant supporting operation down to 1.8V, while 'F' variants typically start at 2.3V, making 'LF' parts preferred for battery-powered or energy-harvesting designs. The PIC16LF1705 integrates Microchip's Intelligent Analog peripherals including on-chip operational amplifiers, a 10-bit ADC with Computation (ADC2), two 8-bit DACs, Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), Zero-Cross Detect (ZCD), and Peripheral Pin Select (PPS). It supports eXtreme Low Power (XLP) modes including Sleep currents down to approximately 20 nA typical and active currents near 35 uA/MHz at 1 MHz, enabling long battery life in sensor and IoT nodes. Typical applications include low-power IoT sensor nodes, battery-powered measurement instruments, white goods and consumer control panels, LED lighting drivers using the COG and on-chip op-amps, general-purpose motor control, and any cost-sensitive 8-bit embedded control design that requires analog integration without an external op-amp or DAC. The through-hole PDIP-14 package simplifies prototyping, breadboarding, and field replacement versus surface-mount alternatives. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VDD pin and consider a 10 uF bulk capacitor near the supply rail. Verify that your selected oscillator configuration matches the application speed and power budget, and consult the device datasheet for ADC acquisition-time calculations and FVR stabilization timing.

询价 联系我们
PIC16LF1705-I/SL - 8-Bit XLP MCU 14KB Flash 14-SOIC | Microchip
PIC16LF1705-I/SL

PIC16LF1705-I/SL - 8-Bit XLP MCU 14KB Flash 14-SOIC | Microchip

The Microchip Technology PIC16LF1705-I/SL is an 8-bit PIC16 microcontroller from the cost-effective PIC® XLP™ 16F family, integrating 14KB (8K x 14) of Flash program memory, 1024 bytes of SRAM, and a 32 MHz internal oscillator in a 14-pin SOIC (SL) package. The LF variant operates across a wide 1.8V to 3.6V supply range and is designed for ultra-low-power (XLP) applications such as battery-powered sensor nodes, IoT edge devices, and energy-harvesting systems. The device features on-chip op amps, a 10-bit ADC, Core Independent Peripherals (CLC, COG/NCO, Zero-Cross Detect), and Peripheral Pin Select (PPS) for design flexibility. An 8-bit microcontroller (MCU) is a compact processor core with on-chip memory and peripherals, optimized for embedded control tasks where low cost, deterministic real-time response, and minimal power consumption outweigh raw computational throughput. The PIC16 architecture sits within the broader Microchip 8-bit hierarchy: PIC10/12/16/18 family → 8-bit MCU → microcontroller → embedded processor → semiconductor. LF variants specifically target the ultra-low-power XLP segment, typically drawing sub-microamp sleep currents suitable for coin-cell and Energy Harvest applications. Key features of the PIC16LF1705 include 32 MHz operation, 14KB Flash with self-programmability, 1024 bytes SRAM, 8-channel 10-bit ADC, two on-chip operational amplifiers, two comparators, an 8-bit DAC, Zero-Cross Detect, Configurable Logic Cells (CLC), Complementary Output Generator (COG), Peripheral Pin Select (PPS), and eXtreme Low Power (XLP) sleep modes. These features are packaged in the 14-pin SOIC footprint for hand-solder-friendly prototyping. Architecturally, the PIC16LF1705 uses a 14-bit instruction-word RISC core with hardware stack, hardware multiplier, and direct/indirect addressing. The Core Independent Peripherals (CLC, COG, Zero-Cross Detect) operate without CPU intervention, reducing latency and power consumption in motor control, lighting, and power-conversion feedback loops. PPS allows peripheral I/O remapping onto most GPIO pins, simplifying PCB layout and BOM. Typical applications include battery-powered IoT sensor nodes, low-cost consumer appliances, LED lighting control with zero-cross detection, small brushed-DC motor control, remote controls, and energy-harvesting wireless switches. The on-chip op amps and comparators make it suitable for analog front-end conditioning without external amplifiers, reducing BOM cost and PCB area in space-constrained designs. When designing with the PIC16LF1705-I/SL, observe the 1.8V to 3.6V supply range, ensure decoupling capacitors (typically 100 nF plus 1 µF bulk) are placed within 5 mm of VDD, and configure unused pins as outputs to minimize sleep current. The PPS feature lets you reassign peripheral outputs to nearly any digital pin, easing layout, but pinout diagrams for the SOIC-14 package remain fixed at the silicon level. This page synthesizes distributor pricing, verified cross-reference drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page, helping sourcing engineers evaluate second-source options and OEM buyers compare lifecycle risk.

询价 联系我们
PIC16LF1705-I/ST - 8-bit 32MHz 14KB Flash XLP MCU | Microchip
PIC16LF1705-I/ST

PIC16LF1705-I/ST - 8-bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip Technology PIC16LF1705-I/ST is an 8-bit PIC® XLP™ 16F microcontroller IC featuring 14KB (8K x 14) of Flash program memory, 1024 bytes of RAM, and a 32 MHz internal core clock, housed in a 14-pin TSSOP package. The part integrates cost-effective Intelligent Analog peripherals including a 10-bit ADC, an operational amplifier (OPAMP), an 8-bit DAC, a high-speed comparator, a zero-cross detect (ZCD), configurable logic cells (CLC), and peripheral pin select (PPS). An 8-bit microcontroller (MCU) is a low-power programmable processor built around an 8-bit data path, well suited to cost-sensitive embedded control. PIC16F170x/171x MCUs combine this 8-bit core with on-chip analog and the eXtreme Low Power (XLP) family of sleep and active modes, occupying a tier in the hierarchy: 8-bit MCU → microcontroller → embedded processor → semiconductor. The 'LF' prefix denotes the wide-voltage 1.8V-3.6V supply variant for battery-powered designs. Key features include 32 MHz max CPU speed from the internal oscillator, 14KB Flash, 1024B SRAM, hardware CLC for combinational/sequential logic without discrete gates, PWM with CCP, and serial interfaces including EUSART, I2C, and SPI. On-chip peripherals such as the 10-bit ADC, op-amp and 8-bit DAC reduce external BOM and PCB area in sensor-interface applications. The architecture combines a RISC-like Harvard core with vectored interrupts and a 14-bit instruction word, enabling compact code density and deterministic interrupt response. PPS allows flexible routing of digital peripherals to any I/O pin, simplifying PCB layout for mixed-signal designs where analog and digital routing would otherwise conflict. Typical applications include IoT sensor nodes, battery-powered instrumentation, LED lighting control, consumer appliances, and low-cost motor control where the integrated op-amp and DAC simplify analog front-ends. Designers commonly pair this MCU with discrete power management and low-power wireless transceivers. When designing with this part, validate current consumption in the chosen sleep mode against battery-life targets: nanoWatt XLP idle currents are well below 1 µA but require correct configuration of the watchdog, brown-out reset and peripheral clocks. PPS remapping must be programmed before peripheral enable to avoid glitches on boot. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the PIC16F170x family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16LF1705T-I/ST - 8-bit XLP MCU 14KB Flash 14-TSSOP | Microchip
PIC16LF1705T-I/ST

PIC16LF1705T-I/ST - 8-bit XLP MCU 14KB Flash 14-TSSOP | Microchip

The Microchip Technology PIC16LF1705T-I/ST is an 8-bit PIC® XLP™ microcontroller featuring 14KB (8K x 14) of Flash program memory, 1024 bytes of SRAM, and a 32 MHz internal oscillator, packaged in a 14-pin TSSOP. Operating from 1.8V to 3.6V on the LF (low-power) silicon process, this device targets ultra-low-power embedded applications while integrating rich analog peripherals including a 10-bit ADC, op-amp, 8-bit DAC, comparator, zero-cross detect, and configurable logic cells (CLC). What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit RISC microcontrollers originally developed by General Instrument and later popularized by Microchip Technology. Within the broader microcontroller taxonomy, PIC MCUs sit alongside ARM Cortex-M and AVR as the dominant 8/16/32-bit embedded controller architectures. The PIC16F family occupies the "mid-range" tier of Microchip's lineup, balancing cost, peripheral integration, and code density using a 14-bit instruction word and a 5-stage pipeline. The LF suffix denotes the low-Flash/Fowler-Nordheim process variant optimized for lower VDD operation and the proprietary nanoWatt XLP™ (eXtreme Low Power) sleep modes that can drop quiescent current to the nanoamp range. Key features of the PIC16LF1705T-I/ST include Core Independent Peripherals (CIPs) such as CLC, PPS (Peripheral Pin Select), the Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG). These allow complex signal generation and timing without CPU intervention, freeing the core for system-level tasks. The 10-bit ADC with hardware Capacitive Voltage Divider (CVD) provides touch-sensing capability and averaged acquisition modes, while the integrated op-amp and 8-bit DAC simplify analog front-end designs in sensor conditioning loops. The device also includes Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) and I2C/SPI interfaces for host communication. Typical applications include IoT sensor nodes, battery-powered consumer electronics, capacitive touch user interfaces, LED lighting controllers, low-end BLDC/PMSM fan control, and small home appliances where the LF process and CIPs reduce BOM cost and firmware complexity. The 32 MHz core delivers roughly 8 MIPS, sufficient for state-machine control loops and simple protocol stacks. When designing with this part, leverage the PPS module to remap digital peripherals to alternative pins—this simplifies PCB routing when only one or two pins are needed on a particular I/O. For lowest sleep power, configure unused peripherals to OFF, enable the FVR (Fixed Voltage Reference) only when needed, and use the RTC with an external 32.768 kHz crystal to time sleep intervals.

询价 联系我们
PIC16LF1707-E/ML - 8-bit 32MHz XLP MCU 3.5KB Flash 20-QFN | Microchip
PIC16LF1707-E/ML

PIC16LF1707-E/ML - 8-bit 32MHz XLP MCU 3.5KB Flash 20-QFN | Microchip

The Microchip PIC16LF1707-E/ML is an 8-bit PIC® XLP™ flash microcontroller delivering 32 MHz CPU performance with 3.5KB (2K x 14 words) of Flash program memory in a 20-pin QFN (4x4 mm) package. It is part of the PIC16F170X family, which combines Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG) with an integrated 10-bit ADC and on-chip op-amps. The "LF" prefix indicates the wide-voltage, low-power variant supporting 1.8V to 3.6V operation, while the "-E/" suffix denotes the extended industrial temperature grade of -40°C to +125°C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and peripheral interfaces onto one silicon die. Within the broader semiconductor taxonomy, an MCU is a subset of microprocessors, which fall under logic ICs and the integrated circuits family. Microchip's PIC® architecture uses a Harvard RISC core with separate program and data buses, and the XLP™ (eXtreme Low Power) designation indicates sleep currents in the nanoamp range - critical for battery-powered and energy-harvesting designs. Key differentiating features of the PIC16LF1707 include the integrated op-amp peripherals that eliminate external analog ICs, 10-bit ADC with computation (ADC2) for automated threshold averaging, and on-chip 5-/8-bit DACs. The device supports up to 18 I/O pins despite its compact 20-QFN footprint, plus peripheral pin select (PPS) for flexible signal routing. The 32 MHz internal oscillator and 4x PLL enable 8 MIPS performance at low power, while the 256 bytes of EEPROM provide non-volatile user data storage. Typical applications span low-power sensor nodes, IoT edge devices, white-goods and appliance controls, LED lighting drivers with analog dimming, and battery-powered instrumentation. The combination of tiny QFN-20 footprint, wide 1.8V-3.6V supply range, and integrated op-amps suits designs where PCB area is at a premium and analog signal conditioning is required near the sensor. When designing with this device, ensure adequate decoupling (100 nF + 1 µF ceramic) within 5 mm of the VDD pin and use the on-chip debug (ICD) interface for in-circuit programming. For noise-sensitive analog paths, place the device's exposed thermal pad (EP) to a grounded copper pour to reduce both thermal resistance and ground bounce on the analog supply rail. This page synthesizes distributor pricing, drop-in alternatives within the PIC16LF170x family, and practical design notes not found in the manufacturer's datasheet - giving you selection clarity for the PIC16LF1707-E/ML in compact, low-power embedded designs.

询价 联系我们
PIC16LF1707-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip DIP-20
PIC16LF1707-E/P

PIC16LF1707-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip DIP-20

The Microchip Technology PIC16LF1707-E/P is an 8-bit PIC16 family flash microcontroller running up to 32 MHz with 3.5 KB (2K x 14) of program Flash memory, housed in a 20-pin PDIP (0.300 inch, 7.62 mm) through-hole package. The "LF" prefix denotes the wide-voltage XLP (eXtreme Low Power) variant, capable of operating across 1.8V to 3.6V from a single Li-ion / two-AA cell stack, while the "E" suffix specifies the -40C to +125C extended operating temperature grade for automotive and industrial environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and I/O on one silicon die. PIC16F/LF170x parts belong to the "PIC16F1xxx enhanced mid-range" family and pair an 8-bit RISC core with Core Independent Peripherals (CIPs) that offload tasks like signal generation, complementary waveform timing, and event-triggered capture from the CPU, lowering interrupt latency and total power. The PIC16LF1707-E/P sits within the power-management IC family hierarchy MCU -> microcontroller -> 8-bit MCU -> PIC16F/LF family -> XLP variants, and is the smallest Flash member of the 170x series in PDIP-20. Key differentiating features include integrated op-amps, a 10-bit ADC with computation (ADC2), a 5/8-bit DAC, two high-speed comparators, an 8-bit timer, a 16-bit timer, and PWM/SMT/CWG/CCP modules, all in a 20-pin footprint. Internal 32 MHz oscillator accuracy supports UART-baud-rate generation without an external crystal in many designs. XLP technology typically delivers < 50 nA sleep current and active currents in the tens of microamperes per MHz, allowing years of operation from a coin cell. Architecturally, the device uses a 14-bit instruction word with a hardware multiplier, a 17-deep stack, and 256 bytes of RAM, with 128 bytes of EEPROM for non-volatile data storage. The Harvard architecture separates program and data buses, enabling single-cycle instruction fetch and improving deterministic real-time response. Core Independent Peripherals reduce firmware complexity by handling timing-critical sequences in hardware, leaving the CPU free for state-machine logic. Typical applications include battery-powered sensor nodes, IoT edge nodes, LED lighting controllers, low-cost consumer appliances, automotive body electronics (when ordered in automotive-qualified grades), and industrial control loops that benefit from on-chip op-amps and comparators. The extended temperature range supports under-hood and outdoor enclosures. When designing with this part, plan decoupling: place a 100 nF ceramic bypass capacitor within 2 mm of VDD and a bulk capacitor on the MCLR/VPP/VDD rails. Verify ICD programming-pin mapping against the chosen package and reserve a 2-pin header for in-circuit serial programming (ICSP) so firmware can be updated without removing the chip. This page synthesizes distributor pricing for the PIC16LF1707-E/P, Microchip 20-pin PDIP drop-in equivalents, and practical design notes (decoupling, ICSP, sleep-mode current budgets) that are not bundled into the manufacturer datasheet.

询价 联系我们
PIC16LF1707-E/SO - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip
PIC16LF1707-E/SO

PIC16LF1707-E/SO - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF1707-E/SO is an 8-bit Flash microcontroller from the PIC16F170x/171x family, offering 3.5KB (2K x 14) of program memory, 256 bytes of SRAM, and 128 bytes of EEPROM in a 20-pin SOIC package. Built on an enhanced mid-range core, it operates up to 32MHz instruction cycle and supports a wide supply voltage range from 1.8V to 3.6V, making it ideal for battery-powered applications. The device integrates a 10-bit ADC, two op-amps, two comparators, a 4-channel PWM module, and a 17 I/O pin capability. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus, used to sense, decide, and actuate in embedded systems. The PIC16LF1707-E/SO belongs to the broader hierarchy of microcontroller -> 8-bit MCU -> Flash MCU -> low-power MCU, optimized for cost-sensitive general-purpose applications requiring minimal power consumption. The 'LF' prefix denotes the low-power 'F' (Flash) variant supporting down to 1.8V operation, while 'XLP' branding reflects Microchip's eXtreme Low Power technology platform. Key features of this part include an integrated 10-bit Analog-to-Digital Converter (ADC), two operational amplifiers (op-amps) that can be configured as rail-to-rail stages, and a peripheral pin select (PPS) mechanism that allows flexible function-to-pin mapping. The on-chip 4-channel Capture/Compare/PWM (CCP) module handles motor control or LED dimming, while the Numerically Controlled Oscillator (NCO) provides precision frequency generation for timing-sensitive applications. CIP (Core Independent Peripherals) like CWG, NCO, and CCL let designers implement complex logic without CPU intervention. Typical applications span IoT sensor nodes, battery-powered remote controls, low-cost motor drivers, LED lighting controllers, and consumer appliances where small pin count, low quiescent current, and integrated analog peripherals reduce BOM cost. The -40C to +125C extended temperature grade (-E suffix) ensures operation in harsh industrial environments. Designers familiar with MPLAB X IDE and XC8 compiler can program and debug this part using PICkit programmers or Curiosity development boards. When selecting the PIC16LF1707-E/SO, prioritize it for designs requiring small 8-bit footprint with on-board op-amps and ADC. If your application needs more I/O or larger memory, consider the PIC16LF1708/1709 family. The SOIC-20 wide-body package (7.50mm width) offers robust handling for hand-prototyping and through-hole conversions with carrier boards.

询价 联系我们
PIC16LF1707-E/SS - 8-bit 32MHz MCU, 3.5KB Flash, 20-SSOP | Microchip
PIC16LF1707-E/SS

PIC16LF1707-E/SS - 8-bit 32MHz MCU, 3.5KB Flash, 20-SSOP | Microchip

The Microchip PIC16LF1707-E/SS is an 8-bit flash microcontroller based on the PIC16 architecture with 3.5KB (2K x 14 words) of program Flash memory and 256 bytes of RAM, housed in a 20-pin SSOP package. It operates from 1.8V to 3.6V (the LF variant targets low-voltage applications), runs at up to 32 MHz internal core clock, and integrates a 10-bit ADC alongside Microchip's core-independent peripherals and eXtreme Low Power (XLP) features. An 8-bit flash microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile Flash program memory, RAM, and configurable peripherals on one silicon die. PIC16 family MCUs use Microchip's proprietary RISC-style instruction set (CISC as documented in the datasheet, but architecturally a streamlined RISC) and dominate cost-sensitive embedded designs thanks to a mature toolchain (MPLAB X IDE, XC8 compiler, PICkit programmer). The LF suffix denotes an extended low-voltage operating range (typically 1.8V-3.6V), making LF parts well suited to battery-powered products. Key features of the PIC16LF1707-E/SS include 3.5KB self-programmable Flash, 256 bytes SRAM, 10-bit ADC with internal voltage reference, multiple timer modules, Enhanced Universal Synchronous/Asynchronous Receiver Transmitter (EUSART), Master Synchronous Serial Port (MSSP) for SPI/I2C, and on-chip debug support. The -E (extended) temperature grade supports -40C to +125C operation for industrial and automotive under-hood applications. The PIC16LF1707 uses Microchip's nanopower XLP technology, achieving sleep currents in the microamp range and active currents of a few hundred microamperes at 1 MHz. This is achieved through aggressive clock gating, multiple low-power sleep modes, and a peripheral module disable mechanism that lets unused peripherals be turned off individually to minimize quiescent draw. Typical applications include low-cost sensor nodes, IoT end devices, LED lighting controllers, small appliances, battery chargers, and consumer electronics. The combination of low price, low power, and integrated ADC makes the PIC16LF1707-E/SS a strong fit where a full Cortex-M0+ design would be over-spec. When designing with this part, allocate at least one ICSP-capable pin set (typically RB6/RB7 or dedicated ICSPCLK/ICSPDAT) and reserve Vpp/MCLR for in-circuit programming. Verify the LF voltage range (1.8V-3.6V) suits your battery chemistry before selecting over the standard F variant (which starts at 2.3V). This page synthesizes current distributor pricing, drop-in package alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

询价 联系我们
PIC16LF1707-I/ML - 8-bit MCU, 2KB Flash, 10-bit ADC | Microchip
PIC16LF1707-I/ML

PIC16LF1707-I/ML - 8-bit MCU, 2KB Flash, 10-bit ADC | Microchip

The Microchip Technology PIC16LF1707-I/ML is a 14/20-pin 8-bit advanced-analog Flash microcontroller built on the PIC16 enhanced mid-range core, housed in a 20-pin QFN (4x4 mm, ML package) with an exposed thermal pad. It integrates 2KB (1K x 14) of self-programmable Flash program memory, 256 bytes of SRAM, and a 10-bit ADC with up to 8 channels and an internal temperature indicator, plus an 8-bit DAC reference, configurable logic cells, and an on-chip 32 MHz internal oscillator. The 'LF' suffix denotes the wide 1.8V-3.6V operating range and eXtreme Low Power (XLP) technology, achieving typical sleep currents below 1 uA, making it ideal for battery-powered designs. A PIC16 microcontroller is a Harvard-architecture 8-bit RISC MCU family from Microchip, sitting in the broader category hierarchy of microcontroller -> embedded processor -> integrated circuit. The 'LF' variant targets low-voltage, low-power applications, while the standard 'F' (1.8V-5.5V) covers wider supply rails. PIC16LF1707 devices are positioned in the cost-sensitive general-purpose segment and combine intelligent analog peripherals with the XLP nanoWatt XLP technology for energy-harvesting and battery-backed designs. Key features include Core Independent Peripherals (CIPs) that execute system functions in hardware without CPU intervention, a 10-bit ADC with computation for hardware-averaged oversampling, an 8-bit Digital-to-Analog Converter (DAC) reference output, two comparators, and a PWM module with complementary outputs. The device supports in-circuit serial programming (ICSP) via two pins, enabling field firmware updates. XLP technology provides multiple low-power modes including Sleep with <1 uA typical current and a Real-Time Clock with 32 kHz external crystal. The PIC16LF1707 uses a 14-bit instruction word and a hardware stack of 16 levels, executing most instructions in one instruction cycle (4 system clock periods). The 32 MHz internal oscillator achieves an effective 8 MIPS throughput, while a 31 kHz low-power LFINTOSC supports low-frequency Sleep operation. The enhanced mid-range core adds hardware-context save/restore for interrupts, lowering firmware overhead in real-time applications. Typical applications include IoT sensor nodes, consumer battery-powered devices such as remote controls and toys, low-cost sensor signal conditioning, white goods and small appliances, LED lighting controllers, and e-metering/HVAC peripherals. The combination of low cost, low power, and integrated analog peripherals makes it suitable for designs that previously required a separate op-amp or ADC chip. When designing with this device, ensure the QFN exposed pad is soldered to a sufficient PCB thermal copper pour to meet the thermal resistance specification. Decouple VDD with at least one 0.1 uF ceramic capacitor close to the pin, and reserve MCLR as a reset input with the recommended pull-up. Program firmware via ICSP using a Microchip programmer (PICkit 4, MPLAB SNAP, or ICD 4) and MPLAB X IDE for development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - giving engineers a single reference to evaluate, source, and design with the PIC16LF1707-I/ML.

询价 联系我们
PIC16LF1707-I/SO - 8-Bit 32MHz 3.5KB Flash MCU | Microchip
PIC16LF1707-I/SO

PIC16LF1707-I/SO - 8-Bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16LF1707-I/SO is an 8-bit flash microcontroller from the PIC16F170x family, combining Intelligent Analog integration with eXtreme Low Power (XLP) technology. The device operates at up to 32 MHz, integrates 3.5 KB of Flash program memory (2K x 14 words), and is housed in a 20-pin SOIC (SO) industrial-temperature package. An 8-bit microcontroller is a small computing system-on-chip that integrates a CPU, RAM, Flash program memory, and a range of peripherals onto a single silicon die. Within the broader taxonomy, the PIC16LF1707 belongs to the microcontrollers category, which itself sits under integrated circuits and finally under semiconductors. The 'LF' suffix denotes a wide-voltage, low-power variant typically optimized for battery-powered applications, while the '170x' series brings Microchip's Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC), Zero-Cross Detect (ZCD), and on-chip op-amps into the cost-sensitive 8-bit segment. Key features include on-chip op-amps, a 10-bit Analog-to-Digital Converter (ADC) with computation, an 8-bit Digital-to-Analog Converter (DAC), a Complementary Waveform Generator (CWG) for half-bridge control, and Peripheral Pin Select (PPS) for flexible signal routing. The XLP nanoWatt technology provides ultra-low sleep currents suitable for energy harvesting and IoT edge nodes. The industrial temperature grade (-40C to +85C) supports a broad set of operating environments. Architecturally, the PIC16LF1707 uses a modified Harvard RISC core with a 14-bit instruction word, allowing dense code packing relative to byte-oriented 8-bit cores. The combination of CIPs and on-chip analog lets designers replace several discrete components with one MCU, reducing both BOM count and PCB area. The CWG, together with PWM and the 8-bit DAC, supports switched-mode power and LED-driving topologies without an external controller IC. Typical applications include LED lighting and luminaire control, switched-mode power supply (SMPS) control loops, battery charging, fan/blower speed control, sensor signal conditioning, low-power IoT sensor nodes, and consumer appliance control panels. The wide operating voltage range and rich peripheral set also make it a fit for general-purpose cost-sensitive embedded designs. When designing with this device, ensure that the MCLR reset line has the proper pull-up and that the VDDCORE capacitor (typically 0.1 uF) is placed as close to the pin as possible. For accurate analog readings, follow Microchip's PCB layout recommendations for the analog VDD/VSS pair and avoid routing digital signals across analog traces. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the PIC16LF1707-I/SO for their specific application.

询价 联系我们
PIC16LF1707-I/SS - 8-bit 32MHz 3.5KB Flash MCU | Microchip
PIC16LF1707-I/SS

PIC16LF1707-I/SS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC16LF1707-I/SS is an 8-bit PIC16 microcontroller built on the eXtreme Low Power (XLP) platform, offering 32MHz CPU performance with 3.5KB (2K x 14) of Flash program memory and 256 bytes of SRAM in a 20-pin SSOP package. It targets low-power, low-voltage applications with 2.3V to 5.5V operation, making it a strong fit for battery-powered and energy-harvesting designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and programmable peripherals. The PIC16 family falls within the 8-bit microcontrollers category, which sits hierarchically under microcontrollers -> embedded processors -> semiconductors. XLP variants like the PIC16LF1707 add nanoWatt XLP technology for ultra-low sleep currents, distinguishing them from standard PIC16F parts that prioritize active performance over standby consumption. Key features include 10-bit ADC with computation (ADC2) for automated signal averaging, zero-cross detect and hardware capacitive voltage divider (CVD) support, two op-amps, a 5-bit DAC, and a 4-channel PWM. Peripheral Pin Select (PPS) is NOT available on this 20-pin variant, but the part retains Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC) and Numerically Controlled Oscillator (NCO). The 20-SSOP outline offers 5.30 mm body width, suited for hand-soldering-friendly prototype boards. The architecture uses a Harvard-style RISC core with a modified 14-bit instruction set optimized for C-code density. The internal 32MHz oscillator eliminates external crystals in many designs. Active current is typically in the microamp range at 1MHz, with sleep currents in the nanoamp range when using the on-chip low-power timer. Typical applications include IoT sensor nodes, wearable health monitors, low-power wireless remote controls, and consumer appliance user interfaces. Designers leverage the 10-bit ADC with hardware CVD for touch-button replacement, reducing BOM cost versus mechanical switches. When designing with this part, ensure decoupling with a 100nF ceramic capacitor placed within 5mm of VDD. For ADC accuracy, add a 10uF bulk capacitor near the AVSS/AVDD rail pair if used. The ICD programming header should reserve pins ICSPCLK/ICSPDAT (RB6/RB7) per the Microchip in-circuit debug specification. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet alone.

询价 联系我们
PIC16LF1707T-I/ML - 8-bit MCU 3.5KB Flash 32MHz QFN-20
PIC16LF1707T-I/ML

PIC16LF1707T-I/ML - 8-bit MCU 3.5KB Flash 32MHz QFN-20

The Microchip PIC16LF1707T-I/ML is a low-power 8-bit Flash microcontroller from the PIC® XLP™ 16F family, delivering 32 MIPS performance at 32 MHz with 3.5 KB (2K x 14) of program Flash memory in a 20-pin QFN (4x4 mm) package with an exposed thermal pad. It combines advanced analog peripherals including a 10-bit ADC and on-chip op-amp with the eXtreme Low Power (XLP) technology platform, making it well suited to battery-operated and energy-harvesting designs that demand long standby life. An 8-bit Flash microcontroller is a small, self-contained computer-on-a-chip built around an 8-bit data path, integrating a CPU, non-volatile program memory (Flash), RAM, and a curated set of peripherals (timers, ADC, comparators, communication ports) on a single die. Within the broader semiconductor taxonomy, the PIC16LF1707 sits as: microcontroller -> 8-bit microcontroller -> embedded controller -> integrated circuit. Microcontrollers of this class typically replace discrete logic and analog front-ends in cost-sensitive and space-constrained designs. The PIC16LF1707 features 256 bytes of SRAM, up to 18 general-purpose I/O pins, an integrated 10-bit ADC with up to 12 channels, two operational amplifiers with rail-to-rail input/output, an 8-bit DAC, two comparators, and peripheral pin select (PPS) for flexible signal routing. XLP technology brings supply current down to a deep-sleep regime suitable for coin-cell applications, while the LF process node (1.8V-3.6V VDD) extends battery life compared to the 5V-capable PIC16F1707 sibling. Peripherals include Master Synchronous Serial Port (MSSP) for SPI/I2C, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and four 10-bit PWM outputs. Architecturally, the device is built on a 14-bit instruction-word enhanced mid-range core with a hardware stack, single-cycle instruction execution (other than branches), and a configurable oscillator block supporting internal 32 MHz HFINTOSC, 31 kHz LFINTOSC, and external crystal modes. Code is protected by a configurable Flash read protection and a unique 32-bit device ID. The integrated op-amps and DAC allow direct analog signal conditioning on-chip, eliminating many external components in sensor-interface and LED-driving applications. Typical applications include low-power IoT sensor nodes, wearable fitness and health devices, battery-powered remote controls, LED lighting controllers with analog dimming, small appliance HMI panels, and consumer electronic accessories where a 20-pin footprint and integrated analog reduce BOM cost. When designing with this device, choose decoupling capacitance per the manufacturer recommended layout (typically 0.1 µF plus 10 µF bulk within 3 mm of the VDD pins), and verify PPS remap constraints before committing to a PCB layout because some peripheral functions must be assigned to specific pins. This page synthesizes distributor pricing, drop-in same-package alternatives from the same PIC16LF1707 family and across Microchip's wider 8-bit portfolio, and practical design notes not found in the standalone datasheet.

询价 联系我们
PIC16LF1707T-I/SO - 8-Bit MCU, 3.5KB Flash, 32MHz, 20-SOIC | Microchip
PIC16LF1707T-I/SO

PIC16LF1707T-I/SO - 8-Bit MCU, 3.5KB Flash, 32MHz, 20-SOIC | Microchip

The Microchip Technology PIC16LF1707T-I/SO is an 8-bit PIC microcontroller in the PIC® XLP™ 16F family, featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and a 32 MHz internal oscillator in a 20-pin SOIC (7.50 mm body) package. The device integrates a 10-bit ADC with up to 17 channels, a 10-bit DAC, a programmable 32 kHz internal oscillator, and the proprietary nanoWatt XLP (eXtreme Low Power) technology that delivers active currents in the microamp range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals such as ADCs, timers, communication interfaces (UART, SPI, I2C), and I/O pins. Within the broader taxonomy, the PIC16LF1707 is a Flash-based 8-bit MCU in the PIC16 enhanced mid-range family, sitting beneath 16-bit dsPIC and 32-bit ARM Cortex parts in computational power but excelling in cost-sensitive and battery-powered applications. The 8-bit architecture trades raw throughput for deterministic instruction execution, predictable interrupt latency, and an exceptionally mature toolchain. Key features include operation from 1.8V to 3.6V (the LF prefix), an integrated 10-bit ADC with up to 17 analog channels, an 8-bit DAC, two 8-bit timers, one 16-bit timer, enhanced PWM modules, EUSART, MSSP (SPI/I2C), up to 18 general-purpose I/O pins, and the nanoWatt XLP sleep current below 1 µA. The internal 32 MHz oscillator eliminates the need for an external crystal in most designs, and the on-board ICD-friendly debug interface simplifies in-circuit programming. Typical applications include low-power sensor nodes, IoT endpoints, wearable health monitors, battery-powered remote controls, LED lighting controllers, and consumer white-goods user interfaces. The wide analog integration also makes it attractive for touch/proximity sensing and small motor-control loops via PWM. The 20-SOIC footprint is hand-solderable and machine-solderable for prototyping as well as high-volume production. When designing with this part, choose decoupling capacitors within a few millimeters of VDD and AVSS pins, reserve a dedicated ICSP header for programming/debug, and use the LF suffix to exploit the full 1.8V-3.6V supply range. This page synthesizes distributor pricing, drop-in alternatives within the PIC16 family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16LF1708-E/ML - 8-bit 32MHz XLP MCU 7KB Flash | Microchip
PIC16LF1708-E/ML

PIC16LF1708-E/ML - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC16LF1708-E/ML is an 8-bit PIC16 microcontroller built on the eXtreme Low Power (XLP) architecture, delivering 32 MHz CPU performance with 7 KB (4K x 14) of Flash program memory in a 20-pin QFN (ML) 4x4 mm package. According to Microchip's PIC16F170X/171X family datasheet, this device targets cost-sensitive general-purpose applications that demand intelligent analog integration with battery-friendly power consumption. What is a PIC16 microcontroller? The PIC16 family is Microchip's mid-range 8-bit RISC microcontroller line, sitting between the baseline PIC10/PIC12 and the enhanced PIC18/PIC24. PIC16 devices use a 14-bit instruction word, support up to 28-56 pins, and integrate peripherals such as 10/12-bit ADC, op amps, comparators, and Core Independent Peripherals (CIPs) including Configurable Logic Cells (CLC), Complementary Output Generator (COG), and Zero-Cross Detect. The PIC16LF1708 specifically adds on-chip op amps, multiple 10-bit ADC channels, and Peripheral Pin Select (PPS), placing it in the 'advanced analog' tier of the family. Key features of the PIC16LF1708 include 7 KB Flash, 512 bytes RAM, 256 bytes EEPROM, 18 I/O pins, two on-chip op amps, one 8-bit DAC, two 10-bit DACs, a 10-bit ADC with up to 17 channels, two comparators, and the XLP sleep current as low as 50 nA typical. The QFN-20 (ML) package offers a compact 4x4 mm footprint suitable for space-constrained PCB designs while exposing the exposed pad for thermal dissipation and ground connection. Architecturally, the PIC16LF1708 uses a Harvard RISC core with a 14-bit instruction set, single-cycle ALU, and direct/indirect addressing modes. The XLP technology combines nanoWatt XLP sleep modes, peripheral module disable, and dynamic oscillator switching to enable multi-year battery life on a single coin cell. The integrated op amps and 10-bit DAC enable closed-loop analog control without external components. Typical applications include battery-powered sensor nodes, LED lighting control, consumer electronics with capacitive touch, low-cost motor control (via COG), smoke detectors, remote controls, IoT edge devices, and portable medical instruments. The combination of op amps, DACs, and PWM makes it especially suited for sensor conditioning and closed-loop analog feedback. When designing with this part, note the -E/ML suffix indicates the -40C to +125C extended operating temperature grade and the QFN-20 (4x4) package. Decoupling capacitors must be placed close to VDD/AVDD and the exposed pad must be soldered to a sufficiently large copper pour for thermal performance. Unused I/O pins should be configured as outputs low to minimize current draw in sleep mode. This page synthesizes drop-in alternatives, design notes, and comparison data not found in the standalone datasheet, helping engineers evaluate PIC16LF1708-E/ML against competing MCUs in the same footprint and voltage class.

询价 联系我们
PIC16LF1708-E/SO - 8-bit MCU, 4KB Flash, 512B RAM, SOIC-20 | Microchip
PIC16LF1708-E/SO

PIC16LF1708-E/SO - 8-bit MCU, 4KB Flash, 512B RAM, SOIC-20 | Microchip

The Microchip Technology PIC16LF1708-E/SO is an 8-bit flash microcontroller in the PIC16F170x/171x family, integrating Intelligent Analog peripherals with eXtreme Low Power (XLP) technology. Housed in a 20-pin SOIC (SO) package, the device provides 4 KB of Flash program memory, 512 bytes of RAM, and operates from a 1.8 V to 3.6 V supply. Its 32 MHz internal oscillator and 16 MIPS core deliver responsive performance for cost-sensitive general-purpose designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals such as timers, ADC, communication interfaces, and I/O pins. In the system hierarchy, an MCU belongs to the embedded computing layer that sits above simple logic ICs and below more complex microprocessors. The PIC16LF1708 falls within the 8-bit RISC MCU category, characterized by a streamlined instruction set that simplifies firmware development while keeping silicon cost low. Key features include on-chip op amps, Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), and Zero-Cross Detect (ZCD), as well as a 10-bit ADC with computation, a 5-/8-bit DAC, and high-speed comparators. The XLP architecture achieves nanoWatt sleep currents below 100 nA, making the device well suited for battery-powered sensors and IoT nodes. Multiple communication interfaces support UART, SPI, and I2C for flexible peripheral expansion. From an architectural perspective, the PIC16LF1708 uses a Harvard RISC core with a 14-bit instruction word and a separate 8-bit data path, providing deterministic interrupt latency and predictable timing. Internal voltage reference, hardware limiting on the ADC, and PWM modules with dead-band control reduce external component count and PCB area in motor control, lighting, and power-conversion applications. Typical applications include low-power IoT sensor nodes, consumer electronics remote controls, battery management for handheld instruments, LED lighting drivers, and small motor or fan control loops. The SOIC-20 footprint simplifies hand prototyping and rework in development labs. When designing with this device, ensure VDD decoupling is placed within 5 mm of the package, and that MCLR is pulled high through a resistor for normal operation. Pair the part with MPLAB X IDE and XC8 compiler to leverage the full peripheral library. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not aggregated on a single manufacturer or distributor datasheet page.

询价 联系我们
PIC16LF1708-E/SS - 8-bit 32MHz MCU 4KB Flash 20-SSOP | Microchip
PIC16LF1708-E/SS

PIC16LF1708-E/SS - 8-bit 32MHz MCU 4KB Flash 20-SSOP | Microchip

The Microchip Technology PIC16LF1708-E/SS is an 8-bit PIC16F microcontroller based on the enhanced mid-range x14 RISC architecture, offering 7KB (4K x 14) of Flash program memory, 512B of RAM, and 32MHz maximum CPU clock speed in a 20-pin SSOP package. It integrates intelligent analog peripherals including a 10-bit ADC, op-amp, 8-bit DAC, high-speed comparator, zero-cross detect, and configurable logic cells (CLC), targeting cost-sensitive applications that still require mixed-signal performance. The PIC16F170x family sits within the PIC microcontroller hierarchy as a mid-range 8-bit MCU with XLP (eXtreme Low Power) technology, making it suitable for battery-powered applications. The LF variant specifically operates over 1.8V to 3.6V, while the F variant operates over 2.3V to 5.5V. The PIC16F170x microcontrollers combine Intelligent Analog integration with low-cost and eXtreme Low Power (XLP) to suit a variety of cost-sensitive general purpose applications. Key features include 4K words of Flash (7KB total addressable), 512 bytes of RAM, 256 bytes of EEPROM, a 10-bit ADC with up to 17 channels, two op-amps, an 8-bit DAC, two high-speed comparators, zero-cross detection, complementary output generator, configurable logic cells, PWM modules, capture/compare/PWM peripherals, and enhanced USART plus I2C/SPI interfaces. Peripheral Pin Select (PPS) enables flexible routing of digital functions to physical I/O pins, reducing PCB constraints. Typical applications include low-power sensor nodes, LED lighting controllers, white-goods and appliance controls, capacitive-touch front panels with CLC-driven scanning, fan/valve control with zero-cross detection for TRIAC switching, low-cost instrumentation with on-chip op-amp signal conditioning, and battery-operated IoT endpoints leveraging XLP sleep currents. Design considerations: ensure core supply decoupling with a 0.1uF ceramic capacitor close to VDD, and reserve the ICSP pins (PGC/PGD) for in-circuit programming access. When using the on-chip op-amp, account for input common-mode range restrictions near the rails. For low-power applications, use the LF variant, leverage the nanoWatt XLP sleep modes, and verify wake-up source selection in the PIE/PIR registers. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16F170x family and competing 8-bit MCU families, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16LF1708-I/P - 8-bit XLP MCU 7KB Flash 20-PDIP | Microchip
PIC16LF1708-I/P

PIC16LF1708-I/P - 8-bit XLP MCU 7KB Flash 20-PDIP | Microchip

The Microchip Technology PIC16LF1708-I/P is an 8-bit PIC16 XLP flash microcontroller delivering up to 32 MHz CPU performance with 7 KB (4K x 14) of program flash, 512 bytes of SRAM and 128 bytes of data EEPROM, housed in a 20-pin PDIP (0.300 inch, 7.62 mm) through-hole package. The LF sub-family targets ultra-low-power (XLP) operation with a wide 1.8 V to 3.6 V core supply, making it ideal for battery-powered and energy-harvesting designs. The device integrates intelligent analog peripherals including on-chip op amps, 8-bit and 10-bit ADCs, 5-bit and 8-bit DACs, comparators, and zero-cross detect, alongside Core Independent Peripherals such as the Configurable Logic Cell (CLC), Complementary Output Generator (COG) and Numerically Controlled Oscillator (NCO). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and configurable peripheral blocks into one package. Within that hierarchy, an 8-bit MCU like the PIC16LF1708 uses a RISC instruction set optimized for deterministic bit-manipulation and low interrupt latency, sitting below 16-bit and 32-bit MCUs in computational throughput but offering superior cost, code-density, and ultra-low-power advantages for compact real-time tasks. The XLP technology inside PIC16LF1708 extends sleep currents to the nanoampere range, supporting coin-cell and energy-harvested products. Key differentiating features include 4 KB instruction-word flash, 512 bytes SRAM, 128 bytes EEPROM, an enhanced mid-range 14-bit instruction set with 200 ns instruction execution, 12-bit ADC with computation (ADC2), high-speed comparators, two op-amp modules, 8-/10-bit PWMs, and the eXtreme Low Power XLP sleep modes. The integrated 32 MHz internal oscillator eliminates external crystal requirements for many designs, and the device supports I2C, SPI, EUSART (RS-232/RS-485), and up to 18 I/O pins. Typical applications include low-cost general-purpose embedded control, IoT sensor nodes, small home appliances, LED lighting controllers, remote controls, sensor signal conditioning, battery chargers, motor control loops for small fans and pumps, and wearable health devices. The PDIP-20 package makes it especially attractive for hobbyist, educational, prototype, breadboard, and through-hole production designs that require easy rework and socket mounting. When designing with the PIC16LF1708-I/P, ensure VDD stays within 1.8 V to 3.6 V and use a 0.1 µF decoupling capacitor close to the supply pin. MPLAB X IDE with XC8 compiler is the recommended toolchain. The trade-off versus QFN variants is approximately 4x larger board area, but you gain mechanical robustness, socket compatibility and easier hand-soldering for prototypes.

询价 联系我们
PIC16LF1708-I/SO - 8-Bit 32MHz XLP MCU 7KB Flash | Microchip
PIC16LF1708-I/SO

PIC16LF1708-I/SO - 8-Bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip PIC16LF1708-I/SO is an 8-bit flash microcontroller from the PIC® XLP™ 16F family, delivering 32 MHz CPU performance with 7 KB (4K x 14 words) of on-chip Flash program memory and 512 bytes of RAM, housed in a 20-pin wide-body SOIC (SO) package rated for the industrial -40 °C to +85 °C temperature range. It targets cost-sensitive, low-power general-purpose applications, drawing from Microchip's eXtreme Low Power (XLP) technology to extend battery life in portable and always-on designs. The device integrates intelligent analog peripherals including configurable op-amps, a high-speed comparator, a 10-bit ADC with automated hardware capacitive voltage division (CVD) touch support, a 10-bit DAC, and core-independent peripherals such as the Configurable Logic Cell (CLC), Complementary Output Generator (COG), Numerically Controlled Oscillator (NCO), and Zero-Cross Detect (ZCD). According to the Microchip datasheet, the LF variant supports a wide 1.8 V to 3.6 V operating range, making it suitable for direct lithium-battery or 3.3 V regulated rails. In system hierarchy, a microcontroller (MCU) sits at the apex of embedded control, integrating a CPU core, non-volatile program memory, volatile data memory, and mixed-signal peripherals into a single die. Within the PIC16 family tree, the PIC16LF1708 is an enhanced mid-range 8-bit MCU that bridges the gap between legacy baseline PIC12/PIC16 parts and higher-pin PIC18/PIC24 devices, optimized for low-power analog-sensing applications. Key differentiating features include 18 available I/O pins, multiple serial interfaces (EUSART, I²C/SPI), four 10-bit PWM channels, a wide operating voltage of 1.8 V to 3.6 V, and nanoWatt XLP sleep currents below 100 nA typical. These features collectively position the PIC16LF1708 as a workhorse for battery-powered IoT nodes, sensor hubs, and low-cost consumer appliances. Architecturally, the PIC16LF1708 uses a 14-bit instruction-word modified Harvard architecture with a 16-level hardware stack and an 8-bit data path. The integrated peripherals operate under the peripheral pin select (PPS) scheme, allowing most digital functions to be remapped to any digital I/O pin—greatly simplifying PCB layout compared with fixed-pin PIC predecessors. Typical applications include handheld consumer electronics, white goods and HVAC sensor interfaces, IoT edge nodes, capacitive-touch user interfaces using the CVD module, LED lighting controllers, and low-power wireless sensor front-ends when paired with a sub-GHz or BLE radio. A primary design consideration is supply decoupling: place a 0.1 µF ceramic bypass capacitor within 5 mm of the VDD pin, and a bulk capacitor of at least 1 µF on the same net, to ensure reliable operation during ADC sampling and radio bursts. This page synthesizes distributor pricing, verified specifications, same-package alternatives, and practical design notes not found in the raw manufacturer datasheet.

询价 联系我们
PIC16LF1708-I/SS - 8-bit 32MHz MCU, 7KB Flash, 20-SSOP | Microchip
PIC16LF1708-I/SS

PIC16LF1708-I/SS - 8-bit 32MHz MCU, 7KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16LF1708-I/SS is an 8-bit PIC microcontroller built on the XLP (eXtreme Low Power) platform, delivering 32 MHz performance from a 14-bit instruction set with 7 KB (4K x 14) of Flash program memory and 512 bytes of SRAM. The part ships in a 20-pin SSOP package and operates across a 1.8 V to 3.6 V supply range for low-voltage, battery-friendly designs. An 8-bit PIC microcontroller is a Harvard-architecture RISC device that integrates CPU, Flash, RAM, EEPROM, and a rich set of peripherals on a single die. Within the broader taxonomy, PIC16F/LF parts sit below 32-bit Cortex-M devices but above simple 8-bit legacy controllers, offering a balance of low cost, low power, and on-chip analog integration. The 'LF' prefix in PIC16LF1708 indicates the wide VDD range optimized for eXtreme Low Power XLP operation, which is critical for energy-harvesting and battery-powered IoT applications. Key features include high-speed comparators, on-chip op amps, Core Independent Peripherals (CLC, COG, Zero Cross Detect), Peripheral Pin Select for flexible routing, and 10-bit ADC with computation. The device also offers 4 x 10-bit PWM, I2C, SPI, and UART interfaces, plus an enhanced Universal Timer. The XLP variant provides sleep currents as low as 20 nA typical, enabling years of operation from a single coin cell. The PIC16LF1708 architecture uses a 14-bit instruction word with 49 instructions, dual 16-bit file select registers for context switching, and a hardware multiplier for efficient math. Its on-chip Intelligent Analog integration (op amps, comparators, 10-bit ADC with computation) makes it suitable for sensor signal conditioning without external components, reducing BOM cost and PCB footprint in mixed-signal designs. Typical applications include IoT sensor nodes, low-power wireless endpoints, consumer white goods, LED lighting control, battery chargers, and small motor control loops. The combination of Core Independent Peripherals and on-chip analog suits cost-sensitive general-purpose designs that previously required external ASICs. When designing with this part, budget the SSOP-20 thermal envelope for ~800 mW at 25 C and ensure decoupling with a 100 nF ceramic close to VDD. Leverage Peripheral Pin Select to remap functions when laying out dense PCBs. This page synthesizes distributor pricing, drop-in alternatives within the PIC16F170x/171x family, and practical design notes not found in the manufacturer datasheet alone, providing information gain over standard distributor listings.

询价 联系我们
PIC16LF1708T-I/SO - 8-bit MCU 7KB Flash 32MHz XLP | Microchip
PIC16LF1708T-I/SO

PIC16LF1708T-I/SO - 8-bit MCU 7KB Flash 32MHz XLP | Microchip

The Microchip Technology PIC16LF1708T-I/SO is an 8-bit flash microcontroller in the PIC16F170x/171x family, delivering 32 MHz CPU performance, 7 KB (4K x 14) of Flash program memory, 512 bytes of SRAM, and integrated intelligent analog peripherals in a 20-pin SOIC (0.295" / 7.50 mm width) package. The 'LF' prefix indicates the wide-voltage low-power (XLP) variant optimized for 1.8V-3.6V operation typical of battery-powered designs. An 8-bit PIC microcontroller is a RISC (Reduced Instruction Set Computer) MCU that combines a small, deterministic instruction set with rich on-chip peripherals, making it well-suited for cost-sensitive embedded control. Positioned in Microchip's hierarchy, it sits below 16-bit dsPIC/PIC24 devices and 32-bit PIC32 MCUs, but offers the lowest unit cost and simplest toolchain for high-volume consumer, industrial, and IoT products. The PIC16F170x family specifically adds Intelligent Analog integration (op-amps, DAC, high-speed comparators) and Core Independent Peripherals (CLC, NCO, Zero-Cross Detect), providing analog-style functionality without CPU overhead. Key features include four 10-bit ADC channels (with Computation mode), two 8-bit DAC outputs, two operational amplifiers configurable for rail-to-rail operation, two high-speed comparators (50 ns response), four 16-bit PWM channels, and a peripheral pin-select (PPS) engine that remaps digital functions to any I/O pin. The device retains 256 bytes of non-volatile EEPROM emulation capability, has an internal 32 MHz oscillator with ±1% accuracy (after calibration), and supports in-circuit serial programming (ICSP) via two pins. The CPU architecture is a Harvard RISC core with a 14-bit instruction word and single-cycle ALU operations at 32 MHz, giving 8 MIPS sustained throughput. A 2-level hardware stack and 49 instruction set deliver compact code density. The XLP technology typically draws 30 nA in Sleep mode with watchdog disabled and under 1 µA with the 32 kHz secondary oscillator active, while active current is around 110 µA/MHz at 3.3V. Typical applications include low-cost sensor nodes, LED drivers and lighting controllers, consumer appliances with touch/proximity sensing, battery-powered IoT end-devices, and small motor/valve controllers. Designers choose this part when they need more analog capability than a baseline PIC16F150x yet want the same low BOM cost. A critical design consideration for the 20-pin SOIC is its 0.300" row spacing, which is wider than the 0.150" TSSOP variant - PCB layout must allocate the larger footprint. Also, the 'LF' low-voltage variant does NOT support 5V operation; use the PIC16F1708 (non-LF) for 5V rails. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16F170x family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC16LF1709-E/SO - 8KB Flash 32MHz 8-bit MCU | Microchip
PIC16LF1709-E/SO

PIC16LF1709-E/SO - 8KB Flash 32MHz 8-bit MCU | Microchip

The Microchip PIC16LF1709-E/SO is an 8-bit flash microcontroller from the PIC16F170x family that combines Intelligent Analog integration with eXtreme Low Power (XLP) technology, packaged in a 20-pin SOIC (SO) outline. It delivers up to 32 MHz CPU performance with 14 KB Flash program memory (8K x 14 words), 1024 bytes of RAM, and integrated peripherals including a 10-bit ADC, on-chip op amps, Core Independent Peripherals (CLC, COG, Zero Cross Detect), and Peripheral Pin Select for flexible pin mapping. The PIC16LF1709-E/SO operates from 1.8 V to 3.6 V, targeting low-voltage battery-powered designs where the F-version (1.8 V min) parts suffice, while industrial-grade PIC16F1709 siblings cover wider supply rails. What is an 8-bit flash microcontroller? An 8-bit flash microcontroller is a single-chip computer built around an 8-bit data path with non-volatile Flash program memory that can be reprogrammed in-circuit, paired with RAM, EEPROM, digital I/O, timers, and analog peripherals. Microcontrollers sit in the broader embedded processing hierarchy: microcontroller -> embedded processor -> microprocessor -> integrated circuit -> semiconductor. The PIC16 family uses a RISC Harvard architecture with separate program and data buses, simplifying instruction fetch and supporting deterministic interrupt response for real-time control. Key features include Active Clock Tuning for HF internal oscillator accuracy, 4-channel PWM with complementary outputs, Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), two SPI/I2C masters, and a hardware touch slider interface. Integrated op amps and a 10-bit ADC with computation (ADC2) reduce external component count in sensor-conditioning designs. The 'LF' prefix denotes the low-voltage F-core variant, while the 'E' suffix indicates an extended temperature grade of -40°C to +125°C. Typical applications include low-cost general-purpose embedded control, IoT sensor nodes, battery-powered consumer devices, capacitive touch user interfaces, LED lighting controllers, and low-power remote controls that benefit from XLP sleep currents in the microamp range. Industrial sensor signal-conditioning applications use the on-chip op amps to eliminate external amplifiers and shrink BOM cost.

询价 联系我们
PIC16LF1709-E/SS - 8-Bit 32MHz MCU, 14KB Flash | Microchip
PIC16LF1709-E/SS

PIC16LF1709-E/SS - 8-Bit 32MHz MCU, 14KB Flash | Microchip

The Microchip Technology PIC16LF1709-E/SS is an 8-bit PIC16LF microcontroller based on the enhanced mid-range core, delivering 32 MHz CPU performance from a 1.8V to 3.6V supply. It integrates 14 KB Flash program memory (8K x 14 words), 1024 bytes of RAM, and is housed in a 20-pin SSOP package. The -E suffix denotes an extended automotive temperature grade of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals. The PIC16LF1709 belongs to the PIC16F170x/171x family, which combines intelligent analog integration with eXtreme Low Power (XLP) technology, suiting cost-sensitive general-purpose applications. Within the broader taxonomy, an MCU sits between discrete logic and a full microprocessor (MPU); PIC MCUs in particular belong to the RISC (Reduced Instruction Set Computer) family using Harvard architecture, and Microchip's mid-range line balances performance, low power, and integrated analog peripherals. Key differentiating features include on-chip operational amplifiers, a high-speed comparator, a 10-bit ADC, an 8-bit DAC, two CCP/PWM modules, Zero Cross Detect (ZCD), Complementary Output Generator (COG), Configurable Logic Cells (CLC), and Peripheral Pin Select (PPS). Communication peripherals include EUSART, I2C, and SPI. The XLP architecture supports nanoWatt sleep currents, making the part attractive for battery-powered and always-on designs. From a technical perspective, the device uses a 14-bit instruction word and supports interrupt-driven operation with a hardware stack. The integrated op-amps can be configured as unity-gain buffers for sensor signal conditioning or cascaded for programmable-gain stages, while the COG module drives power switches without CPU overhead. PPS routes digital peripherals to any I/O pin, simplifying PCB layout when peripheral use changes late in the design. Typical applications include LED lighting control, sensor conditioning front-ends, small appliance control, low-power IoT sensor nodes, automotive body and lighting modules, and battery chargers. In each of these, the combination of integrated analog, low sleep current, and PPS-driven flexibility reduces the external BOM. Designers should size the decoupling network (typically 100 nF plus 10 uF bulk) close to VDD and AVDD pins and verify the program memory endurance (10K erase/write cycles typical) against in-field firmware update frequency. Unused op-amp and DAC outputs should be tied to a defined voltage rather than left floating.

询价 联系我们
PIC16LF1709-I/ML - 8-Bit MCU, 14KB Flash, 32MHz, 20-QFN | Microchip
PIC16LF1709-I/ML

PIC16LF1709-I/ML - 8-Bit MCU, 14KB Flash, 32MHz, 20-QFN | Microchip

The Microchip PIC16LF1709-I/ML is an 8-bit PIC® XLP™ 16F microcontroller with 14KB (8K x 14) Flash program memory, 1024 bytes RAM, and a 32 MHz internal oscillator, housed in a 20-pin QFN (4x4) package with exposed thermal pad. It combines intelligent analog peripherals, including a 10-bit ADC, with Microchip's eXtreme Low Power (XLP) technology to suit cost-sensitive general-purpose applications across industrial, consumer, and automotive segments. An 8-bit microcontroller (MCU) is a programmable logic device that integrates a CPU, memory (Flash for program storage, RAM for data, and EEPROM for non-volatile data), and peripherals (ADC, timers, communication interfaces) on a single silicon die. The PIC16LF1709 belongs to the PIC16F family of RISC-architecture MCUs, sitting within the broader taxonomy of 8-bit microcontrollers -> microcontrollers -> embedded processors -> semiconductors. The 'LF' suffix denotes the low-voltage variant operating from 1.8V to 3.6V, making it suitable for battery-powered and energy-harvesting designs. Key features include 14KB self-programmable Flash, 1024 bytes SRAM, 256 bytes EEPROM, a 10-bit ADC with up to 17 channels, two op amps, two comparators, two 8-bit DACs, an 8-bit/16-bit timer architecture, and a 10-bit PWM module. The device also integrates Core Independent Peripherals such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), and Zero Cross Detect (ZCD), along with Peripheral Pin Select (PPS) for flexible I/O mapping. Communication interfaces include I2C, SPI, and EUSART with auto-baud detect. Architecturally, the PIC16LF1709 employs a Harvard RISC core with 49 instructions and a 16-level hardware stack, delivering predictable deterministic interrupt response and low-latency I/O. The XLP feature set (nanoWatt XLP) supports sleep currents down to the nanoampere range, enabling multi-year battery life in IoT sensor nodes. The 20-pin QFN (4x4 mm) variant (suffix /ML) provides a compact footprint suited to space-constrained PCB designs. Typical applications include IoT sensor nodes, low-power wireless sensor hubs, battery-powered consumer electronics, HVAC and white-goods control boards, automotive body electronics (non-safety), LED lighting controllers, and small industrial control modules. The wide 1.8V to 3.6V operating range also supports direct connection to single-cell Li-ion or two-cell alkaline battery stacks. When designing with this MCU, allocate at least one PPS reassignment to bring critical signals onto the desired physical pins, since PPS lets peripheral functions be mapped to multiple I/O. For RF-noisy environments, place the 0.1 uF decoupling capacitor within 3 mm of the VDD pin and connect AGND to DGND at a single star point to prevent ground-loop ADC errors. This page synthesizes distributor pricing, drop-in PIC16LF170x-family alternatives, and practical low-power design notes not found in the manufacturer datasheet summary.

询价 联系我们
PIC16LF1709-I/P - 8-bit XLP MCU, 14KB Flash, 20-PDIP | Microchip
PIC16LF1709-I/P

PIC16LF1709-I/P - 8-bit XLP MCU, 14KB Flash, 20-PDIP | Microchip

The Microchip Technology PIC16LF1709-I/P is a cost-effective 8-bit flash microcontroller from the PIC16F170x/171x family, built around an enhanced mid-range PIC16 RISC core that delivers 200 ns instruction execution. Housed in a 20-pin PDIP (0.300", 7.62 mm) through-hole package, the part runs at up to 32 MHz internal clock, integrates 14 KB (8K x 14 words) of Flash program memory, 1024 bytes of SRAM, and 256 bytes of EEPROM, with on-chip Intelligent Analog peripherals including a 10-bit ADC, an 8-bit DAC, two operational amplifiers, a high-speed comparator, a zero-cross detect (ZCD) block, configurable logic cells (CLC), complementary output generator (COG), and Peripheral Pin Select (PPS). The 'LF' variant supports a wide 1.8V-3.6V operating range and uses Microchip's eXtreme Low Power (XLP) technology, with active current in the microamp range and sleep currents as low as the datasheet's nanoamp class. A PIC (Peripheral Interface Controller) microcontroller is a family of 8-bit RISC-based microcontrollers from Microchip Technology that pair a Harvard-architecture CPU with Flash program memory and on-chip peripherals. Within the broader taxonomy, a PIC sits under microcontroller -> embedded MCU -> semiconductor device. The 'LF' suffix denotes a low-voltage, low-power variant suited to battery-powered designs, while 'I/P' indicates the industrial temperature grade (-40C to +85C) and PDIP package. This combination places the PIC16LF1709-I/P at the intersection of an 8-bit MCU and an analog-rich analog-front-end (AFE) device, allowing the chip to replace multiple external analog components. Key differentiating features are the on-chip dual op-amps (rail-to-rail input/output), the 8-bit DAC with internal reference, CLC blocks that implement combinatorial logic without CPU intervention, and PPS that remaps digital peripherals onto a wide choice of I/O pins. The integrated 10-bit ADC has up to 12 channels in the 20-pin variants, enabling direct interface to sensors without an external mux. These features let designers shrink BOM cost and PCB area in cost-sensitive analog signal-chain applications. Architecture is an 8-bit accumulator-based Harvard design with a 14-bit instruction word, supporting 49 instructions and a hardware stack. The vectored interrupt controller handles on-chip peripherals and the interrupt-on-change feature, while the on-chip voltage regulator generates the 1.8V core supply from VDD. The device is supported by Microchip's MPLAB X IDE, XC8 C compiler, and MPLAB Code Configurator (MCC) for rapid peripheral setup. Typical applications include LED lighting drivers (using the COG and PWM), sensor signal conditioning (op-amp + ADC), battery chargers (ZCD + ADC + DAC), consumer appliances with touch or capacitive sense (using CLC), small motor control (PWM + COG for complementary drive), and IoT edge nodes powered by coin cells where XLP sleep currents extend battery life. The 20-PDIP package targets prototype builds, hobbyist projects, and industrial control boards that need through-hole replacement or hand-soldered assembly. When designing with this part, ensure decoupling is placed close to VDD/AVDD and that the ICSP/PGD/PGC pinout is reserved for in-circuit serial programming. Choose PIC16F1709-I/P if your supply is fixed at 2.3V-5.5V and you prefer the broader voltage range; choose PIC16LF1709-I/P for 1.8V-3.6V battery operation where XLP run/sleep currents matter. This page synthesizes distributor pricing, drop-in alternatives, application notes, and design considerations not aggregated on a single manufacturer or distributor product page.

询价 联系我们