集成电路

子分类

📁 ADC/DAC 2519 产品 📁 放大器IC 796 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 296 产品 📁 DSP 963 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1583 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18721 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32787)

PIC32MX110F016B-I/SO - 32-bit MCU, 40 MHz, 16 KB Flash, 28-SOIC | Microchip
PIC32MX110F016B-I/SO

PIC32MX110F016B-I/SO - 32-bit MCU, 40 MHz, 16 KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC32MX110F016B-I/SO is a 32-bit RISC microcontroller based on the MIPS32 M4K core, delivering up to 40 MHz CPU performance in a 28-pin SOIC package. The part integrates 16 KB of Flash program memory and 4 KB of SRAM, with peripheral features including up to 10 channels of 10-bit ADC, four DMA channels, two I2S/SPI modules, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing via mTouch. Operating voltage is 2.3 V to 3.6 V with industrial temperature range of -40 °C to +105 °C. A microcontroller (MCU) is a single-chip computer that contains a processor core, program memory (Flash), working memory (RAM), and a configurable set of peripherals such as ADC, timers, and communication interfaces. Within the broader semiconductor hierarchy, MCUs sit between microprocessors (which require external memory) and System-on-Chip (SoC) devices (which integrate radio and application-specific accelerators). The PIC32MX family is Microchip's mid-range 32-bit MCU line, positioned above the 16-bit PIC24F and below the higher-pin-count PIC32MZ families. Key differentiators of this device include Peripheral Pin Select (PPS) for remapping most digital peripherals to any I/O, a Parallel Master Port (PMP) for graphics interfaces, and CTMU hardware support that simplifies mTouch capacitive-button firmware. Boundary Scan (JTAG) is supported for production test access. USB and high-speed analog blocks from larger PIC32MX members are intentionally omitted in this 16-KB variant, making it the lowest-cost entry point in the family. Typical applications include low-cost capacitive touch user interfaces, consumer appliances with graphics LCDs via PMP, USB-less industrial sensors, and general-purpose embedded control. Compared with a discrete 8-bit MCU plus external ADC, the PIC32MX110F016B integrates peripherals and 32-bit compute into a single SOIC-28 footprint, reducing PCB area and BOM count. Designers should note that the 28-SOIC package is 0.300" wide (not the narrow 0.150" version); use appropriate land pattern. Decoupling: place a 100 nF ceramic near each VDD/VSS pair, with a 10 µF bulk capacitor at the regulator output. For CTMU touch sensing, follow Microchip AN1250 PCB layout guidelines to minimize trace-to-trace capacitance that can degrade touch sensitivity. This page synthesizes drop-in alternatives in the same 28-SOIC footprint, current distributor stock and pricing, and practical design considerations not found in the manufacturer datasheet.

询价 联系我们
PIC32MX110F016B-I/SS - 40MHz 32-bit MCU 16KB Flash | Microchip
PIC32MX110F016B-I/SS

PIC32MX110F016B-I/SS - 40MHz 32-bit MCU 16KB Flash | Microchip

The Microchip PIC32MX110F016B-I/SS is a 32-bit MIPS32 M4K microcontroller delivering 40 MHz CPU performance with 16 KB Flash and 4 KB SRAM in a 28-pin SSOP package. It is part of the PIC32MX1XX/2XX family of general-purpose microcontrollers and is targeted at cost-sensitive embedded designs that need more performance than 8/16-bit MCUs can offer while retaining a simple peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripherals such as timers, ADC, and communication interfaces on one die. The PIC32MX1XX/2XX family belongs to the broader category of 32-bit microcontrollers -> RISC microcontrollers -> MIPS32-based MCUs -> embedded processors -> semiconductors. It is designed as an entry-level upgrade path for engineers migrating from PIC16/PIC24 devices who need higher throughput for USB, graphics, or audio front-end tasks. Key features include a 10-bit ADC with up to 12 analog input channels, four hardware DMA channels, a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing, two UART, two SPI, and two I2C peripherals, plus a Parallel Master Port (PMP) for graphics or external memory expansion. The 21 general-purpose I/O pins support Peripheral Pin Select (PPS), which allows digital peripheral signals to be remapped to a wide range of physical pins, simplifying PCB layout. The device operates from 2.3 V to 3.6 V with industrial -40C to +85C temperature range. Internally the PIC32MX110F016B uses the MIPS32 M4K core with single-cycle hardware multiply/divide, a 5-stage pipeline, and a separate PLL for the system clock. Five 16-bit timers/counters and a configurable watchdog with on-chip low-power RC oscillator provide robust task scheduling. The part supports ICSP (In-Circuit Serial Programming) and JTAG debugging through the MPLAB X IDE with the free XC32 compiler, enabling rapid firmware development. Typical applications include USB HID devices, low-cost audio playback front-ends, capacitive touch user interfaces, sensor hubs, and small graphic LCD controllers. The combination of CTMU, DMA, and PMP makes it a fit for human-machine interface (HMI) panels and consumer appliances. When designing with this MCU, allocate the 16 KB Flash budget carefully - the bootloader plus USB stack plus application code leaves only a few KB for user logic. Use the CTMU and DMA offload the CPU from touch scanning to keep MIPS available for application work. Pin 1 dot marker should be observed carefully for SSOP-28 land pattern. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and buyers a single reference for evaluation.

询价 联系我们
PIC32MX110F016B-V/SP - 40MHz 32-bit MCU, 16KB Flash | Microchip
PIC32MX110F016B-V/SP

PIC32MX110F016B-V/SP - 40MHz 32-bit MCU, 16KB Flash | Microchip

The Microchip Technology PIC32MX110F016B-V/SP is a 32-bit RISC microcontroller built on the MIPS32 M4K core, running up to 40 MHz with less than 0.5 mA/MHz current consumption, housed in a 28-pin SPDIP package. The device integrates 16 KB of Flash program memory and 4 KB of SRAM, 21 general-purpose I/O pins, and operates from a 2.3 V to 3.6 V supply across a -40 °C to +105 °C industrial temperature range. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich peripheral set on one die. Within the broader taxonomy, PIC32MX devices sit between 8-bit PIC16/PIC18 MCUs and higher-end Cortex-M parts, forming Microchip's mid-range 32-bit MCU family targeting audio/graphics, USB, and advanced analog applications. The PIC32MX110F016B-V/SP is positioned as the entry-level Flash member of the PIC32MX1XX/2XX 28/36/44-pin family, optimized for cost-sensitive designs that still need DSP-class throughput and USB connectivity. Key differentiating features include Peripheral Pin Select (PPS) for flexible function-to-pin remapping, a Parallel Master Port (PMP) for graphics interfaces, two I2S/SPI modules for codec/serial audio, a 10-bit ADC with multiple analog channels, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. Direct Memory Access (DMA) offloads CPU data movement, while five 16-bit timers (and up to two 32-bit timers) give flexible event timing. AEC-Q100 qualification supports automotive deployment, especially in the -V (industrial-grade) operating range. Architecturally, the MIPS32 M4K core executes most instructions in a single cycle with hardware multiply/divide and a 5-stage pipeline. The 16 KB Flash and 4 KB SRAM are sized for compact control loops, USB device stacks (CDC/HID/MSD), and small graphical user interfaces rendered via PMP to external LCD controllers. DMA channels move peripheral data to RAM without CPU intervention, leaving headroom for application code. Typical applications include low-cost USB peripherals, capacitive touch human-machine interfaces (HMIs), audio/graphic control panels using external PMP-attached LCDs, sensor conditioning nodes with on-chip ADC, and general-purpose industrial controllers. The automotive-grade (-V) variant also suits body-electronics and HMI modules where AEC-Q100 qualification is required. Design consideration: with less than 0.5 mA/MHz active current, regulator choice should focus on low-noise, low-IQ LDOs; bulk decoupling of 10 µF ceramic plus 0.1 µF HF bypass near each VDD pin is recommended per the family datasheet. PPS routing must be reconfigured after each reset, so save PPS maps in non-volatile configuration. This page synthesizes distributor pricing (as of 2026-10-01), drop-in same-package alternatives from Microchip's PIC32MX1XX/2XX family, and practical design notes not aggregated on a single manufacturer or distributor page.

询价 联系我们
PIC32MX110F016B-V/SS - 40MHz 32-bit MCU, 16KB Flash, 28-SSOP | Microchip
PIC32MX110F016B-V/SS

PIC32MX110F016B-V/SS - 40MHz 32-bit MCU, 16KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC32MX110F016B-V/SS is a 32-bit MIPS M4K microcontroller operating at 40 MHz with 16 KB Flash and 4 KB SRAM, housed in a 28-pin SSOP (R-PDSO-G28) surface-mount package. The device runs from a 2.3V to 3.6V supply, delivers up to 21 general-purpose I/O pins, and integrates peripherals such as two I2S/SPI modules, a Parallel Master Port (PMP), Peripheral Pin Select (PPS), and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, communication controllers, and analog blocks. The PIC32MX1XX/2XX family belongs to the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. Within Microchip's portfolio, the PIC32MX sits between the 16-bit PIC24F/G and the higher-end PIC32MZ families, balancing MIPS performance, low power, and rich peripheral integration for cost-sensitive designs. Key differentiating features include Peripheral Pin Select (PPS), which remaps most digital peripherals to any compatible I/O pin - dramatically simplifying PCB layout and reducing pin conflicts. The integrated CTMU enables capacitive touch measurement via a single ADC channel and timing source, supporting mTouch buttons, sliders, and proximity sensing without an external touch controller. The PMP interface supports graphics LCDs, and the dual I2S/SPI blocks support audio codecs and full-duplex serial communications. Architecturally, the PIC32MX110F016B-V/SS uses the MIPS32 M4K core with a 5-stage pipeline, hardware multiply/divide, and tightly-coupled SRAM for deterministic interrupt response. The Flash program memory supports self-programming via the boot Flash region, and the device includes an on-chip debugger accessible through the ICSP interface using MPLAB Snap, MPLAB ICD-4, or PICkit 4. Typical applications include consumer audio peripherals, low-cost HMI panels, capacitive-touch human-interface devices, USB HID peripherals, industrial sensor hubs, and low-power IoT edge nodes. The wide operating temperature range (-40C to +105C) and 2.3V-3.6V supply suit battery and industrial 3.3V bus systems. The PIC32MX110F016B-V/SS offers compelling price-to-performance compared with 8/16-bit MCUs for designs requiring MIPS-class throughput without the cost of higher-tier PIC32MZ parts. Design tip: place a 0.1 uF decoupling capacitor as close as possible to every VDD/VSS pair, and connect the MCLR pin through a 10 kohm pull-up to VDD for proper reset behavior. Use PPS to assign peripherals to convenient pins during schematic capture, and configure the CTMU via the dedicated CTMUCON register set for accurate touch measurements. This page synthesizes distributor pricing, drop-in alternatives within the PIC32MX1XX family, application companion ICs, and practical design notes beyond the manufacturer datasheet DS60001168L, supporting BOM optimization and second-source decisions.

询价 联系我们
PIC32MX110F016BT-V/ML - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip
PIC32MX110F016BT-V/ML

PIC32MX110F016BT-V/ML - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip

The Microchip Technology PIC32MX110F016BT-V/ML is a 32-bit MIPS32 M4K RISC microcontroller running at 40 MHz, equipped with 16 KB of Flash program memory and 4 KB of SRAM, in a 28-pin QFN (6 x 6 mm) package with an exposed thermal pad. It operates from 2.3 V to 3.6 V and is qualified to AEC-Q100 for automotive applications, with a temperature range of -40 °C to +105 °C. The device integrates USB Full-Speed, two I²S/SPI modules, two UART/I²C modules, a Parallel Master Port (PMP) for graphics interfaces, and Peripheral Pin Select (PPS) for flexible routing of digital peripherals. A microcontroller (MCU) is an integrated circuit containing a CPU core, program and data memory, and programmable peripherals such as timers, communication interfaces, and analog blocks. PIC32MX110F016B sits inside the Microchip PIC32MX family, which in turn belongs to the broader 32-bit microcontroller category within the larger family of embedded processors that includes ARM Cortex-M, RISC-V, and MIPS architectures. MCUs are the central compute element of nearly every embedded system, executing firmware that interacts with sensors, actuators, displays, and external buses. Key features of this device include 21 general-purpose I/O pins, four DMA channels with automatic data size detection, a 10-bit ADC with multiple channels, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive-touch sensing. Two separate PLLs (one for the CPU, one for USB) simplify mixed-clock designs, and five 16-bit timers cover a wide range of PWM and capture/compare tasks. The configurable Watchdog Timer with on-chip Low-Power RC oscillator enhances safety in noisy or low-power modes. The architecture combines a MIPS32 M4K core with Microchip's Peripheral Pin Select (PPS) fabric, allowing remapping of most digital peripherals to virtually any I/O pin. This is especially valuable in compact 28-pin designs where pin assignments often conflict with PCB layout, eliminating the need to re-spin a board for routing reasons. The integrated Full-Speed USB 2.0 device controller with on-chip transceiver simplifies connectivity without an external PHY. Typical applications include automotive body and infotainment modules, USB Human Interface Devices (HIDs) such as keyboards and mice, graphics interfaces via PMP for low-cost LCDs, capacitive touch panels using mTouch, and industrial control nodes. The wide operating voltage range and AEC-Q100 qualification make it well-suited to automotive and harsh industrial environments. When designing with this device, allocate PCB copper under the exposed pad for thermal relief and ensure the decoupling network uses 100 nF plus bulk capacitance within a few millimetres of the supply pins. The PPS feature must be configured at startup; forgetting to enable a peripheral's PPS mapping is a common first-time designer pitfall. This page synthesizes official Microchip specifications, AEC-Q100 automotive qualification details, drop-in PIC32MX1x0 family alternatives, and practical design notes that are not assembled in a single place on the manufacturer datasheet or distributor listing.

询价 联系我们
PIC32MX110F016BT-V/SO - 40MHz 32-bit MCU 16KB Flash | Microchip
PIC32MX110F016BT-V/SO

PIC32MX110F016BT-V/SO - 40MHz 32-bit MCU 16KB Flash | Microchip

The Microchip PIC32MX110F016BT-V/SO is a 32-bit MIPS32 M4K RISC microcontroller operating at 40 MHz, integrating 16 KB of Flash program memory and 4 KB of SRAM in a 28-pin SOIC package. It belongs to the PIC32MX1x0 family and is supplied from a 2.3 V to 3.6 V rail with 21 general-purpose I/O pins, supporting an operating temperature range of -40 °C to +105 °C for industrial and AEC-Q100 automotive grade deployments. A 32-bit microcontroller (MCU) is a programmable computing element that executes instructions from on-chip Flash memory, drives digital I/O, and interfaces with analog peripherals such as ADC, comparators and timers. PIC32MX1x0 devices sit at the low-memory end of the broader PIC32 family — they extend Microchip's PIC architecture into 32-bit territory while preserving the MPLAB X IDE and Harmony ecosystem. They are descendants of the original PIC microcontroller line, which established the 8-bit MCU category, and represent the migration path into higher-performance MIPS-based silicon for embedded designs. Key features include a single-core MIPS32 M4K CPU running up to 40 MHz with < 0.5 mA/MHz active current, on-chip 10-bit ADC, two I²S/SPI modules for audio codec connectivity, Peripheral Pin Select (PPS), a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) supporting mTouch™ capacitive touch buttons and sliders. Five 16-bit general-purpose timers and DMA channels enable offloading of repetitive data movement. Architecturally, the device uses Harvard-style separated instruction/data buses with a 5-stage pipeline, single-cycle multiply and hardware divider, and tightly-coupled peripheral buses. USB 2.0 full-speed, I²C, UART, SPI, and PMP peripherals share pins through the PPS multiplexer, simplifying PCB routing in compact 28-pin layouts. Typical applications include automotive body electronics, industrial control panels, consumer audio peripherals, USB HID devices, and low-cost graphical user interfaces driving small LCDs. The wide operating voltage range and -40 °C to +105 °C thermal envelope also suit outdoor IoT edge nodes. When designing with this MCU, ensure decoupling uses 100 nF + 10 µF placed within 5 mm of the VDD pins; PPS reassignments must be configured at runtime and unlocked via IOLOCK before peripheral changes. The 'T' suffix denotes tape-and-reel packaging; the 'V' temperature code designates the -40 °C to +105 °C automotive-grade window. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SOIC footprint, and practical design notes not consolidated on the manufacturer product page, providing procurement-grade context for engineers evaluating PIC32MX1x0 devices.

询价 联系我们
PIC32MX110F016BT-V/SS - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip
PIC32MX110F016BT-V/SS

PIC32MX110F016BT-V/SS - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip

The Microchip Technology PIC32MX110F016BT-V/SS is a 32-bit MIPS M4K microcontroller running at 40 MHz, integrating 16 KB of Flash and 4 KB of SRAM in a 28-pin SSOP package. It supports an operating voltage range of 2.3V to 3.6V and is AEC-Q100 qualified for automotive applications. What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/SRAM), and a rich set of peripherals (UART, I2C, SPI, timers, ADC, PWM, etc.) into one package. 32-bit MCUs execute instructions over a wider data path than 8-bit or 16-bit MCUs, enabling higher computational throughput, larger addressable memory, and more efficient handling of complex algorithms. Within the Microchip taxonomy, the PIC32MX family sits at the low-power / cost-optimized end of the 32-bit PIC32 portfolio, bridging the gap between 16-bit PIC24/dsPIC devices and high-performance PIC32MZ parts. Key features include two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. The 40 MHz CPU with MIPS32 M4K core delivers less than 0.5 mA/MHz active current, and the part includes up to four DMA channels, two UART, and two I2C modules. The AEC-Q100 "V" suffix designates the automotive grade, making this part suitable for in-vehicle designs. The PIC32MX110 architecture uses a 5-stage pipeline MIPS32 M4K core with single-cycle hardware multiply and divide, paired with separate PLLs for CPU and USB clocks. PPS allows digital peripheral I/O to be remapped to most general-purpose I/O pins, simplifying PCB layout. Multiple power-management modes (Run, Idle, Sleep) plus a configurable WDT with on-chip low-power RC oscillator support long battery-life or energy-harvesting applications. Typical applications include automotive body electronics and HMI nodes, capacitive touch buttons and sliders via mTouch, USB audio peripherals, low-cost graphics interfaces through PMP, and general-purpose 32-bit embedded control. The wide peripheral mix and automotive qualification also make it suitable for industrial sensor hubs and consumer appliances requiring a 32-bit upgrade path from 16-bit PIC24 designs. When designing with this MCU, reserve a clean 3.3V analog rail for the AVDD pin pair and place the decoupling capacitors within 3 mm of the supply pins. The PPS registers must be unlocked and configured before any remapped peripheral works correctly - failing to do this is one of the most common bring-up pitfalls for first-time PIC32 users. This page consolidates distributor pricing, automotive-grade drop-in alternatives, and practical design guidance that the bare Microchip datasheet does not present together.

询价 联系我们
PIC32MX110F016C-I/TL - 32-bit 40MHz 16KB Flash MCU | Microchip
PIC32MX110F016C-I/TL

PIC32MX110F016C-I/TL - 32-bit 40MHz 16KB Flash MCU | Microchip

The Microchip PIC32MX110F016C-I/TL is a 32-bit MIPS32 M4K microcontroller running at 40 MHz with 16 KB Flash and 4 KB SRAM, housed in a 36-pin VTLA (5x5 mm) package with an exposed thermal pad. It operates from 2.5 V to 3.6 V and is qualified to the industrial -40C to +85C temperature range. The part integrates rich connectivity (I2C, IrDA, LIN, PMP, SPI, UART/USART) and Microchip's Peripheral Pin Select (PPS) for flexible signal routing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripherals. The PIC32MX110 family belongs to the broader 32-bit MCU category, which sits above 8-bit and 16-bit MCUs in performance and addresses the same role as ARM Cortex-M0/M3 parts. Within Microchip's portfolio, the 32-bit MIPS-based PIC32 line competes with the dsPIC and PIC24 16-bit lines as well as Microchip's own ARM-based SAM family. Key features include 16 KB (16K x 8) Flash, 4 KB SRAM, hardware DMA (up to 4 channels), configurable Watchdog Timer with on-chip Low-Power RC oscillator, multiple power-management (Sleep/Idle) modes, and JTAG/ICSP debug. PPS remaps digital peripherals to almost any I/O pin, easing PCB layout for dense designs. The device is built around a MIPS32 M4K Harvard core with single-cycle hardware multiply and a 5-stage pipeline. The 40 MHz core delivers approximately 50 DMIPS, and the bus matrix connects the core, DMA engine, and peripherals without stalling the CPU. The 36-VTLA package uses an exposed pad for thermal relief. Typical applications include consumer and industrial embedded control, USB-less PIC32 designs, sensor hubs, low-cost graphical user interfaces (with PMP to TFT/segment LCD), and educational or hobby platforms. The 16 KB Flash / 4 KB SRAM balance fits small TCP/IP or USB stacks running on a sister PIC32 part. When designing, allocate Flash budget carefully - 16 KB accommodates roughly 12 KB of code after the bootloader, leaving limited room for field-upgrade images. Plan ICSP pins early: any PGECx/PGEDx pair is valid for debug and programming, but only as a matched pair. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32MX110F016C-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016C-V/TL

PIC32MX110F016C-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip Technology PIC32MX110F016C-V/TL is a 32-bit MIPS M4K microcontroller from the PIC32MX1xx/2xx family, integrating 16 KB of Flash program memory and 4 KB of SRAM in a 36-pin VTLA (5x5 mm) package with exposed thermal pad. It operates at up to 40 MHz with sub-0.5 mA/MHz active current, and is rated for the automotive -40C to +105C temperature range (V-temp grade). The device targets audio, graphics, USB-capable, and general-purpose embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of peripheral interfaces into one package. The PIC32MX110F016C belongs to the broader category of 32-bit microcontrollers, which sit architecturally above 8-bit and 16-bit MCUs and below microprocessor units (MPUs) that require external memory. Within Microchip's portfolio it occupies the low-pin-count, low-memory tier of the PIC32MX family, suitable for cost-sensitive applications that still demand 32-bit performance, DSP capability, and modern peripherals. Key features include two I2S/SPI modules for audio codec interfacing, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics or memory-mapped peripherals, and a Charge Time Measurement Unit (CTMU) that supports mTouch capacitive touch sensing. Integrated connectivity includes I2C, IrDA, LINbus, SPI, UART/USART, and PMP. On-chip system resources comprise Brown-out Detect/Reset, DMA, POR, PWM, and a Watchdog Timer, enabling robust single-chip designs in industrial and automotive environments. The M4K core delivers 1.56 DMIPS/MHz and supports the MIPS32 instruction set including DSP ASE extensions, allowing efficient audio decoding and signal-processing workloads at modest clock rates. The 2.3V-3.6V single-supply range simplifies integration with 3.3V analog and digital peripherals, while the VTLA-EP package exposes a thermal pad for improved heat spreading during continuous full-load operation. Typical applications include automotive body and comfort modules, consumer audio accessories with I2S codecs, low-cost HMI panels using PMP-driven LCDs, capacitive-touch user interfaces leveraging CTMU, and LIN-bus slave nodes. The AEC-Q100 qualification makes it a direct fit for in-cabin automotive electronics. When designing with this device, observe the 3.3V supply limit, use PPS to remap peripherals to convenient package pins, and follow Microchip's PIC32MX1xx/2xx family reference manual for oscillator and PLL configuration. Decouple VDD/AVDD with 100 nF plus bulk capacitance placed within 5 mm of each pin pair. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC32MX1xx/2xx family, and practical design notes that complement the Microchip datasheet with sourcing and selection guidance.

询价 联系我们
PIC32MX110F016CT-I/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016CT-I/TL

PIC32MX110F016CT-I/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip Technology PIC32MX110F016CT-I/TL is a 32-bit MIPS M4K microcontroller with 16KB of Flash program memory and 4KB of SRAM, operating at up to 40MHz. It is housed in a 36-pin VTLA (5x5 mm) package with an exposed thermal pad, optimized for compact surface-mount designs that demand high MIPS-per-dollar performance in a small footprint. What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash and RAM), and peripherals (UART, I2C, SPI, ADC, timers) into one package. The PIC32MX family sits in the hierarchy: microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32MX family -> PIC32MX1xx sub-family. It targets cost-sensitive applications where 8-bit MCUs run out of headroom but full application processors are overkill, bridging the gap between Microchip's PIC16/PIC24 lines and higher-end PIC32MZ devices. Key features include 16KB of Flash with self-programming support, 4KB of SRAM, a 10-bit 1 Msps ADC with up to 13 channels, two UART, two I2C, and two SPI modules, plus five 16-bit timers/counters. The peripheral pin select (PPS) feature allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB routing. The device operates from 2.3V to 3.6V and supports industrial temperature ranges of -40C to +85C. Architecturally, the MIPS32 M4K core delivers 1.56 DMIPS/MHz with single-cycle multiply and hardware divide, supported by a 5-stage pipeline. The integrated DMA controller with up to four channels offloads data movement between peripherals and memory, freeing the CPU for application code. Separate PLLs handle CPU and USB clocking, enabling flexible system timing. Typical applications include low-cost IoT sensor nodes, USB device peripherals, consumer appliances, industrial control interfaces, and human-machine interface (HMI) touch panels. The combination of small package, USB 2.0 full-speed support, and rich peripherals makes the PIC32MX110F016C family a versatile entry point for embedded designs. When designing with this MCU, ensure the exposed thermal pad is properly soldered to a sufficient copper pour to meet thermal specifications. Use MPLAB X IDE with XC32 compiler for development, and consider the PIC32MX1xx/2xx family datasheet and the family reference manual for peripheral programming details. This page consolidates distributor pricing, drop-in alternative options within the PIC32MX family, and practical design notes that supplement the manufacturer datasheet.

询价 联系我们
PIC32MX110F016CT-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016CT-V/TL

PIC32MX110F016CT-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip PIC32MX110F016CT-V/TL is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering up to 40 MHz clock speed, 16 KB of Flash program memory and 4 KB of SRAM, housed in a 36-pin VTLA (5x5 mm, 0.5 mm pitch) surface-mount package. The device offers 25 general-purpose I/O lines and an AEC-Q100 qualification for automotive applications, with connectivity including I2C, SPI, UART/USART, IrDA, LINbus and PMP. A 32-bit microcontroller (MCU) is an integrated circuit that combines a high-performance CPU, program memory (typically Flash), data memory (SRAM), and programmable peripherals on a single die. The PIC32MX1x0 family sits in Microchip's PIC32 portfolio above 8-bit PIC16/PIC18 and 16-bit PIC24 dsPIC parts but below the high-pin-count PIC32MZ series. It targets cost-sensitive, mixed-signal embedded designs that require deterministic real-time behaviour, low power consumption, and rich connectivity. Within the broader semiconductor taxonomy, the PIC32MX110F016CT-V/TL is a microcontroller (MCU), a member of the system-on-chip (SoC) category, used in power management, sensing, and control subsystems. Key features include a 5-channel 10-bit ADC for analog sensing, 4 hardware DMA channels, Peripheral Pin Select (PPS) for flexible pin mapping, a 16-bit timer/counter, and configurable WDT with on-chip low-power RC oscillator. The device supports 1.6 MIPS per MHz performance and operates across a 2.3 V to 3.6 V supply, suitable for battery-powered and industrial-grade systems. Architecture-wise, the MIPS32 M4K core implements a 5-stage pipeline and executes most instructions in a single cycle. A separate PLL provides flexible clock generation from the internal 8 MHz RC oscillator or external crystal, and dedicated DMA engines offload peripheral data movement from the CPU, improving determinism. Typical applications include automotive body electronics (LIN-bus nodes, HVAC controls, sensor clusters), industrial sensor hubs, IoT edge nodes, low-cost HMI touch pads, and consumer white-goods controllers where AEC-Q100 qualification and LINbus compliance are required. When designing with this part, place a 0.1 µF decoupling capacitor close to each VDD/VSS pair and follow the recommended 4-layer PCB stack-up to keep EMI below AEC-Q100 limits. This page synthesises distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX110F016D-I/ML - 32-bit MCU 40MHz 16KB Flash 44-QFN | Microchip
PIC32MX110F016D-I/ML

PIC32MX110F016D-I/ML - 32-bit MCU 40MHz 16KB Flash 44-QFN | Microchip

The Microchip Technology PIC32MX110F016D-I/ML is a 32-bit RISC microcontroller built on the MIPS32 M4K core, running at 40 MHz with 16 KB of Flash program memory and 4 KB of SRAM, housed in a 44-pin QFN (8x8 mm) package with an exposed thermal pad. It operates from a 2.3V to 3.6V supply and supports an industrial temperature range of -40 °C to +105 °C. A 32-bit microcontroller (MCU) is an integrated processor core, program memory, data memory, and a rich set of peripherals on a single silicon die. PIC32MX devices sit in Microchip's PIC32 family under the MIPS32 M4K architecture, a branch of the broader microcontroller category within the power management and embedded computing domain. They balance deterministic real-time performance with high code density. Key features include two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, a Parallel Master Port (PMP) for graphics interfaces, a Charge Time Measurement Unit (CTMU) that enables mTouch capacitive-touch buttons and sliders, four DMA channels, and a 10-bit ADC. The CTMU, PPS, and PMP combination differentiates this MCU from simpler ARM Cortex-M0+ parts that require external glue logic for capacitive touch and graphics. At 40 MHz the core draws less than 0.5 mA/MHz active current, while the on-chip 1.5 Msps 10-bit ADC, five 16-bit general-purpose timers, and a real-time clock and calendar (RTCC) provide sufficient analog and timing depth for sensor-hub, HMI, and low-cost graphics products. JTAG and two-wire programming/debug interfaces are included for development. Typical applications include consumer and industrial human-machine interfaces (HMIs), low-cost graphical LCD or segment displays driven through PMP, capacitive-touch control panels using CTMU-based mTouch firmware, USB device or audio bridges leveraging the integrated I2S modules, and sensor hubs combining ADC, RTCC, and DMA for low duty-cycle battery-powered products. When designing with this device, allocate pins for the I2S, PMP, and JTAG interfaces early, since PPS remapping cannot replace lost physical pins; use the exposed pad of the QFN package as the primary ground and thermal path. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC32MX1xx family, and practical design notes that go beyond what the manufacturer datasheet lists in isolation.

询价 联系我们
PIC32MX110F016D-I/PT - 32-bit MCU, 16KB Flash, 40MHz, TQFP-44 | Microchip
PIC32MX110F016D-I/PT

PIC32MX110F016D-I/PT - 32-bit MCU, 16KB Flash, 40MHz, TQFP-44 | Microchip

The Microchip PIC32MX110F016D-I/PT is a 32-bit MIPS32 M4K RISC microcontroller operating up to 40 MHz, with 16 KB Flash and 4 KB SRAM, housed in a 44-pin TQFP (10x10 mm) package. It integrates up to 21 general-purpose I/O, 4 DMA channels, two I2S/SPI modules, and an on-chip 10-bit ADC, all operating from a 2.3 V to 3.6 V rail. Typical dynamic current is below 0.5 mA/MHz, making it a strong fit for low-power embedded designs. What is a PIC32MX microcontroller? The PIC32MX family is Microchip's line of 32-bit MIPS-based microcontrollers, sitting in the taxonomy: microcontroller -> embedded MCU -> 32-bit MCU -> MIPS M4K core. PIC32MX parts combine the legacy PIC peripheral set with the wider 32-bit MIPS datapath, providing integer performance up to ~52 DMIPS at 40 MHz while keeping code-density benefits of the MIPS instruction set. Key features include Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics or external memory interfaces, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders, brown-out reset, power-on reset, and five 16-bit timers. The integrated 10-bit ADC, multiple UART/I2C/SPI peripherals, and USB-ready companion peripherals allow this device to replace external logic in cost-sensitive nodes. From an architectural standpoint, the PIC32MX110F016D uses a Harvard-style MIPS32 M4K core with separate Flash and SRAM buses, supporting 16 KB Flash for code and 4 KB SRAM for data. Its DMA controller offloads I/O from the CPU, and the CTMU provides a precise time-measurement current source for touch sensing without external analog components. Typical applications include low-cost USB device nodes, capacitive touch user interfaces, small graphics LCDs driven by PMP, industrial sensor conditioning nodes, and consumer appliances needing 32-bit headroom at 8-bit prices. The industrial temperature grade (-40 C to +85 C) suits outdoor enclosures and factory-floor deployments. When designing with this part, ensure the 2.3 V to 3.6 V supply is decoupled with 100 nF plus 10 uF bulk capacitors close to the VDD pins, and use PPS to remap peripherals when the PCB layout forces non-standard pin assignments. For migration, the same die is offered in 44-QFN (PIC32MX110F016D-V/ML) for space-constrained boards. This page synthesizes distributor pricing, verified drop-in alternatives within the same Microchip 44-pin TQFP family, and practical design notes that are not consolidated in the manufacturer datasheet alone.

询价 联系我们
PIC32MX110F016D-V/ML - 40MHz 32-bit MCU, 16KB Flash | Microchip
PIC32MX110F016D-V/ML

PIC32MX110F016D-V/ML - 40MHz 32-bit MCU, 16KB Flash | Microchip

The Microchip PIC32MX110F016D-V/ML is a 32-bit MIPS32 M4K RISC microcontroller running at 40 MHz with 16 KB of on-chip Flash and 4 KB of SRAM, packaged in a 44-pin QFN (ML) 8x8 mm with an exposed thermal pad for improved thermal dissipation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (SRAM), and a rich set of peripherals onto one silicon die. Within the broader taxonomy, the PIC32MX110F016D belongs to the PIC32MX1xx family of general-purpose 32-bit microcontrollers, which sits under Microchip's PIC32 family and ultimately under the MIPS-based MCU product line for embedded control. The 'D' suffix denotes an integrated Parallel Master Port (PMP) for graphics and external memory interfacing, while the 'V' temperature grade extends the operating range to -40C to +105C for industrial environments. Key features include up to 21 general-purpose I/O pins with Peripheral Pin Select (PPS) remapping, two I2S/SPI modules for codec and audio interfacing, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing, an RTCC, 3 analog comparators, and 4-channel DMA. The device consumes less than 0.5 mA/MHz active current and operates from 2.3 V to 3.6 V. Additional peripherals include five 16-bit timers, two UART modules, two I2C modules, and a 10-bit 1 Msps ADC. Architecturally, the PIC32MX110F016D uses a Harvard-style MIPS32 M4K core with a 5-stage pipeline, single-cycle hardware multiply/divide, and a prefetch cache to maximize throughput from Flash. The result is deterministic interrupt response suitable for hard real-time control, while the integrated DMA engine offloads repetitive peripheral data movement from the CPU. Typical applications include industrial control panels with capacitive touch, low-cost audio playback with I2S DACs, USB device nodes (via on-chip USB FS), graphical user interfaces using PMP, smart sensors, and home appliances. The integrated CTMU makes the part particularly attractive for cost-sensitive human-machine interfaces. When designing with this device, ensure the exposed pad (EP) is soldered to a sufficient ground copper pour to meet thermal and electrical performance; verify PPS remapping against the device variant's pin map; and use MPLAB XC32 with the appropriate compiler license to unlock optimizations above -O1. This page synthesizes current distributor pricing, verified drop-in alternatives from the same PIC32 family, and practical design notes that go beyond what the manufacturer datasheet alone offers.

询价 联系我们
PIC32MX110F016DT-I/ML - 32-bit 40MHz MCU 16KB Flash | Microchip
PIC32MX110F016DT-I/ML

PIC32MX110F016DT-I/ML - 32-bit 40MHz MCU 16KB Flash | Microchip

The Microchip Technology PIC32MX110F016DT-I/ML is a 32-bit RISC microcontroller from the PIC32MX1XX/2XX family, featuring a MIPS32 M4K core running up to 40 MHz with 16 KB of Flash and 4 KB of SRAM in a 44-pin QFN (8x8 mm) package with exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals on one die. The PIC32MX110F016D specifically combines a 32-bit MIPS core (M4K) with the cost-effective peripheral set typical of Microchip's PIC32 entry-level portfolio. Within the broader taxonomy, this part sits in the hierarchy: PIC32MX1XX -> PIC32MX family -> PIC32 -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The M4K core executes most instructions in a single cycle and supports the standard MIPS32 instruction set, giving it noticeably higher throughput than 8-bit or 16-bit alternatives at similar clock rates. Key features include an operating voltage range of 2.3V to 3.6V (3.3V typical), industrial-grade -40C to +105C temperature range, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics interfaces, two I2S/SPI modules for audio codec connectivity, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing, and up to 32 KB of Flash in the family. The device also integrates separate PLLs for CPU and USB clocks, two UART and I2C modules, and multiple low-power modes with less than 0.5 mA/MHz active current consumption. The architecture uses a 5-stage pipeline with hardware multiply/divide and a deterministic interrupt controller, making the M4K core well suited to real-time control. On-chip DMA (up to 4 channels with automatic data size detection) offloads data movement from the CPU, freeing bandwidth for application code. USB 2.0 full-speed device capability is supported through the dedicated USB PLL, removing the need for an external clock source in many designs. Typical applications include consumer electronics with USB connectivity, audio playback and processing (using I2S), low-cost graphics user interfaces via PMP, capacitive touch button or slider panels using CTMU, and general-purpose 32-bit embedded control upgrades for legacy PIC24 or PIC16 designs. The PIC32MX110F016DT-I/ML ships in tape and reel packaging for high-volume assembly. Designers should verify pin assignment against the specific 44-QFN variant - the 'ML' suffix denotes the 8x8 mm QFN package, whereas the 'PT' suffix denotes TQFP-44. The 'T' character in the MPN indicates tape-and-reel delivery, and the 'I' indicates the -40C to +105C industrial temperature grade. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not all available in the manufacturer datasheet alone.

询价 联系我们
PIC32MX110F016DT-I/TL - 32-bit MCU 16KB Flash 40MHz 44-VFTLA | Microchip
PIC32MX110F016DT-I/TL

PIC32MX110F016DT-I/TL - 32-bit MCU 16KB Flash 40MHz 44-VFTLA | Microchip

The Microchip Technology PIC32MX110F016DT-I/TL is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering up to 40 MHz CPU clock performance with less than 0.5 mA/MHz active current consumption. It integrates 16 KB of Flash program memory and 4 KB of SRAM in a 44-pin VFTLA (VTLA) exposed-pad surface-mount package, combining 32-bit processing throughput with a rich peripheral set for cost-sensitive embedded applications. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and programmable peripherals on one die. Within the broader semiconductor taxonomy, the PIC32MX family sits between 8/16-bit legacy MCUs and high-end Cortex-M cores, targeting the "32-bit performance at near 16-bit cost" design point. The M4K core adds DSP-like arithmetic and Single-Cycle Multiplication to help audio and graphics signal processing without a dedicated DSP. Key differentiating features of this part include two I2S/SPI modules for codec interfacing, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics displays, and a Charge Time Measurement Unit (CTMU) that enables Microchip's mTouch capacitive touch buttons and sliders. Five 16-bit general-purpose timers, up to four DMA channels with automatic data size detection, separate PLLs for CPU and USB clocks, and 21 general-purpose I/O pins complete the peripheral set. The PIC32MX110F016DT-I/TL is specified for an industrial temperature range of -40C to +105C and operates from 2.3 V to 3.6 V. The 'T' code in the part number indicates tape-and-reel packaging, 'I' indicates industrial temperature grade, and 'TL' designates the 44-pin VFTLA package. The compact 6 mm x 6 mm 0.65 mm-pitch package with exposed thermal pad helps thermal dissipation and PCB density. Typical applications include consumer audio accessories using I2S codecs, low-cost graphical user interfaces with PMP-driven LCDs, capacitive-touch user input panels leveraging CTMU, USB device peripherals using the on-chip USB peripheral and dedicated PLL, and general-purpose industrial control nodes that need 32-bit math at low BOM cost. When designing with this part, remember that PPS remaps must be unlocked before use, and the 2.3 V minimum supply rules out 1.8 V-only rails. The exposed thermal pad should be soldered to a continuous ground copper pour for electrical and thermal performance. This page synthesizes distributor pricing, drop-in VFTLA alternatives, and practical design notes not found in a single manufacturer datasheet. Refer to Microchip's PIC32MX1XX/2XX datasheet family for peripheral electrical specifications.

询价 联系我们
PIC32MX110F016DT-V/ML - 32-bit 40MHz MCU, 16KB Flash, 44-QFN | Microchip
PIC32MX110F016DT-V/ML

PIC32MX110F016DT-V/ML - 32-bit 40MHz MCU, 16KB Flash, 44-QFN | Microchip

The Microchip PIC32MX110F016DT-V/ML is a 32-bit RISC microcontroller based on the MIPS32 M4K core, operating at up to 40 MHz, and housed in a 44-pin QFN (8x8 mm) package with an exposed thermal pad. It integrates 16 KB of Flash program memory, 4 KB of SRAM, and is supplied from a 2.3 V to 3.6 V rail while consuming less than 0.5 mA/MHz active. The device includes two I2S/SPI modules, two UART and I2C modules, a Parallel Master Port (PMP) for graphics interfaces, Peripheral Pin Select (PPS) for flexible signal mapping, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive-touch sensing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable peripherals. The PIC32MX family belongs to the broader class of 32-bit microcontrollers, which sit between 8/16-bit MCUs (used for simple control tasks) and high-end application processors (used for operating systems and rich UI). The MIPS32 M4K core used in this part supports MIPS16e mode for up to 40% smaller code size, reducing Flash footprint for compact embedded applications. Within Microchip's portfolio, the PIC32MX1x0 series is positioned as an entry-level 32-bit MCU for cost-sensitive designs. Key features of the PIC32MX110F016DT-V/ML include hardware DMA with up to four channels and automatic data size detection, separate PLLs for CPU and USB clocks, configurable WDT with an on-chip low-power RC oscillator, and multiple power management modes for energy-constrained designs. The operating temperature range is -40 °C to +105 °C (grade -V), making it suitable for industrial environments. The QFN-44 package exposes a thermal pad that should be soldered to the ground plane to lower thermal resistance. Architecturally, the device pairs the M4K pipeline with a dedicated peripheral bus, allowing DMA-driven I/O without CPU intervention. PPS allows most digital peripherals to be remapped to a wide range of I/O pins, simplifying PCB routing. CTMU enables reliable capacitive touch sensing using a constant-current source and timer capture, eliminating external touch ICs. Typical applications include consumer electronics with graphical user interfaces using the PMP, USB device/host peripherals (where USB is present in this family), industrial control panels, capacitive touch user interfaces, and low-cost IoT sensor nodes. The combination of small Flash, moderate SRAM, and rich peripherals makes it a common choice for bridging 8-bit PIC users to 32-bit performance. When designing with this part, allocate the QFN exposed pad to a continuous ground copper pour with multiple thermal vias for best thermal and electrical performance. Configure PPS carefully during firmware bring-up because mis-mapped peripherals can appear as silent failures. For USB applications, ensure the 48 MHz PLL is correctly tuned and the USB transceiver bypass capacitors follow the reference design. This page synthesizes verified distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the PIC32MX110F016DT-V/ML for new designs and second-source decisions.

询价 联系我们
PIC32MX110F016DT-V/PT - 40MHz 32-bit MCU, 16KB Flash, AEC-Q100 | Microchip
PIC32MX110F016DT-V/PT

PIC32MX110F016DT-V/PT - 40MHz 32-bit MCU, 16KB Flash, AEC-Q100 | Microchip

The Microchip Technology PIC32MX110F016DT-V/PT is a 32-bit MIPS32 M4K microcontroller operating at 40 MHz with 16 KB (16K x 8) Flash program memory and 4 KB SRAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package. The device is part of the PIC32MX1xx family and is qualified to the AEC-Q100 automotive standard, making it suitable for automotive and industrial applications operating from -40C to +105C. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a 32-bit processor core, program and data memory, and a rich set of peripherals (timers, communication interfaces, ADC/DAC, GPIO) into one package. Within the broader semiconductor taxonomy, an MCU belongs to the category of microcontrollers -> embedded processors -> integrated circuits. The PIC32MX family uses the MIPS32 M4K core, which sits in the same RISC lineage as other 32-bit MCU cores like ARM Cortex-M and competes in cost-sensitive embedded segments where deterministic performance and rich peripheral integration are required. Key features of the PIC32MX110F016DT-V/PT include Peripheral Pin Select (PPS) for flexible signal assignment, a Parallel Master Port (PMP) for graphics interfaces, two I2S/SPI modules for codec and serial audio communication, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders, five 16-bit general-purpose timers, and an operating voltage range of 2.3V to 3.6V. The part supports up to 21 I/O ports and integrates USB, I2C, UART, SPI, and PMP peripherals. The 5V tolerant I/O and AEC-Q100 Grade 3 qualification enable deployment in automotive body and infotainment subsystems. The architecture is built around the MIPS32 M4K Harvard-style core with separate instruction and data paths, single-cycle hardware multiply, and a multi-channel DMA controller for offloading data movement. The 40 MHz operation delivers approximately 50 DMIPS of computational throughput while consuming less than 0.5 mA/MHz, balanced for always-on and battery-tolerant designs. Five 16-bit timers can be paired to generate 32-bit timing events, and the CTMU simplifies touch-button and capacitive slider implementation without external analog front-ends. Typical applications include automotive body electronics and HVAC controls, low-cost graphics HMI with PMP-driven TFT panels, USB audio peripherals and consumer audio codecs, capacitive touch user interfaces (mTouch), and industrial control nodes requiring AEC-Q100 qualification. The wide peripheral mix makes it well-suited for bridging legacy MCU designs into more capable 32-bit platforms. When designing with this part, ensure your linker script reserves both the 16 KB Flash and 4 KB SRAM regions; the PIC32MX1xx family is offered in multiple memory density variants and choosing the wrong density at firmware-build time can silently truncate the image. The PPS feature must be configured before peripheral use, and the CTMU requires calibration of the internal current source for stable touch readings. This page synthesizes distributor pricing, AEC-Q100 drop-in alternatives in the same 44-pin TQFP footprint, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX110F016DT-V/TL - 32-bit MCU 16KB Flash 40MHz | Microchip
PIC32MX110F016DT-V/TL

PIC32MX110F016DT-V/TL - 32-bit MCU 16KB Flash 40MHz | Microchip

The Microchip Technology PIC32MX110F016DT-V/TL is a 32-bit RISC microcontroller from the PIC32MX1XX/2XX 28/36/44-pin family, featuring a MIPS32 M4K core running up to 40 MHz with MIPS16e code compression for up to 40% smaller code size. It integrates 16 KB of Flash program memory and 4 KB of SRAM in a 44-pin VTLA surface-mount package, with the "V" suffix denoting the automotive-grade -40C to +105C operating temperature range. A 32-bit microcontroller (MCU) is an integrated processor core, memory, and peripherals on a single die, designed to execute complex firmware at higher throughput than 8-bit or 16-bit alternatives. Within the semiconductor hierarchy, the PIC32MX sits under MCU -> microcontroller -> embedded processor -> semiconductor device. The PIC32MX1XX family specifically targets cost-sensitive 32-bit applications that previously used 16-bit devices, combining deterministic real-time control with the rich peripheral integration required by audio, graphics, USB, and advanced analog front ends. Key features of the PIC32MX110F016DT-V/TL include an operating voltage window of 2.3 V to 3.6 V, less than 0.5 mA/MHz active current consumption, two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible function remapping, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders. AEC-Q100 qualification makes this part suitable for automotive applications. The M4K pipeline delivers 1.56 DMIPS/MHz and supports both 32-bit and 16-bit instruction modes via MIPS16e. Up to four channels of hardware DMA with automatic data size detection offload data movement from the CPU, while separate PLLs for the CPU and USB clocks allow independent optimization of core performance and USB Full-Speed compliance. Five 16-bit general-purpose timers provide flexible event timing. Typical applications include automotive body and chassis ECUs, industrial HMI panels with graphics, USB device peripherals, capacitive touch human-interface modules, audio interface controllers using I2S, and low-cost 32-bit replacements for legacy 16-bit designs. The wide peripheral set reduces external component count. When designing with this MCU, allocate at least one decoupling capacitor pair (100 nF + 4.7 uF) per power pin pair (VDD/AVDD and VSS/AVSS), follow the recommended programming/debug header pinout from the datasheet for ICSP, and respect the 2.3 V minimum supply during Flash programming cycles. This page synthesizes distributor pricing, AEC-Q100-grade drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32MX120F032B-50I/SS - 50MHz 32-bit MCU 32KB Flash | Microchip
PIC32MX120F032B-50I/SS

PIC32MX120F032B-50I/SS - 50MHz 32-bit MCU 32KB Flash | Microchip

The Microchip Technology PIC32MX120F032B-50I/SS is a 32-bit MIPS32 M4K RISC microcontroller running up to 50 MHz, integrating 32 KB of Flash program memory and 8 KB of SRAM, in a 28-pin SSOP package. The PIC32 core delivers 1.56 DMIPS/MHz performance while keeping active current consumption below 0.5 mA/MHz, with peripheral-rich connectivity including two I2S/SPI modules, two UART modules with LIN and IrDA support, two I2C channels, four DMA channels, and a Parallel Master Port (PMP) for graphics interfaces. It operates from 2.3 V to 3.6 V and across an industrial temperature range of -40 C to +105 C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and configurable peripherals onto one die. The PIC32MX1XX/2XX family sits in the hierarchy: microcontroller -> 32-bit MCU -> MIPS M4K architecture -> Microchip PIC32MX series -> entry-level flash-MCU segment. Designed for connected and low-power embedded designs, the PIC32MX120 line is the lowest pin-count / lowest Flash member of the family, targeting cost-sensitive applications that still need 32-bit performance, USB-OTG, or graphics peripherals. Key features that distinguish this part include Peripheral Pin Select (PPS), which remaps most digital I/O to virtually any I/O pin for flexible PCB routing; a 16-bit Parallel Master Port (PMP) for external memory or graphics; a Charge Time Measurement Unit (CTMU) for mTouch capacitive-touch buttons and sliders; and a 10-bit 1 Msps Analog-to-Digital Converter with up to 13 analog input channels. The PIC32MX120 also integrates a real-time clock-calendar, a watchdog timer, and multiple power-management modes that drop quiescent current into the microamp range for battery-powered designs. Architecturally, the PIC32MX120 uses a Harvard-style MIPS32 M4K core with a 5-stage pipeline, single-cycle multiply, hardware divide, and tightly-coupled prefetch module to keep Flash accesses from bottlenecking execution. The 50 MHz (-50) speed grade is the higher-performance bin of the family and supports 50 MHz operation across the full industrial temperature range, while the 40 MHz (-40) grade supports 40 MHz only. Industrial-grade silicon (-I) is rated to 105 C ambient. Typical applications for the PIC32MX120F032B-50I/SS include low-cost consumer devices, mTouch capacitive touch user interfaces, audio playback systems using the I2S codec interface, low-end graphics terminals driven by PMP, USB device peripherals in the 28-pin form factor, and industrial sensor / control nodes. The 32 KB Flash comfortably holds small graphical menus, USB stacks (e.g. Microchip MLA / Harmony Lite), and RTOS workloads. When designing with this part, plan for an external supervisor or internal POR delay for clean reset behavior, place the 8 MHz-40 MHz crystal within 10 mm of the OSC pins, and follow Microchip's recommendations for decoupling (0.1 uF + 4.7 uF within 5 mm of each VDD/VSS pair). The CTMU requires an external current-setting resistor; PPS mappings must be locked after configuration to avoid glitches during runtime. For migration to higher pin-count members, the PIC32MX130/150/170/270 families share this die with additional Flash and peripherals and are upward-compatible in software. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SSOP footprint, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX120F032B-I/SO - 40MHz 32-bit MCU 32KB Flash 28-SOIC | Microchip
PIC32MX120F032B-I/SO

PIC32MX120F032B-I/SO - 40MHz 32-bit MCU 32KB Flash 28-SOIC | Microchip

The Microchip Technology PIC32MX120F032B-I/SO is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering 40 MHz CPU performance in a 28-pin SOIC wide-body (SO) package with up to 32 KB Flash and 8 KB SRAM. It integrates 4 DMA channels, Peripheral Pin Select (PPS), a Parallel Master Port (PMP), and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. What is a PIC32 microcontroller? A PIC32 is Microchip's family of 32-bit microcontrollers based on the MIPS32 architecture, positioned above the 8-bit PIC16/PIC18 and 16-bit PIC24 families in the embedded hierarchy. PIC32 devices offer higher MIPS-per-mHz than 8/16-bit predecessors while retaining the MPLAB X toolchain and Harmony ecosystem, making them a stepping stone from legacy 8/16-bit designs to full 32-bit performance. Key features of the PIC32MX120F032B-I/SO include 21 general-purpose I/O lines, two I2S/SPI modules for codec and serial communications, five 16-bit timers, a 10-channel 10-bit ADC at up to 1 Msps, and current consumption below 0.5 mA/MHz under typical conditions. The device supports an operating voltage range of 2.3 V to 3.6 V and an industrial temperature range of -40 °C to +105 °C. Architecturally, the PIC32MX120F032B uses the MIPS M4K 32-bit RISC pipeline with single-cycle multiply and hardware divide, paired with a dedicated DMA controller that offloads data movement between peripherals and RAM. The 10/100 Ethernet MAC is absent in the -120 sub-family, distinguishing it from higher-density PIC32MX1xx/2xx siblings; however, the integrated PMP, I2S, and CTMU blocks make it a strong fit for low-cost graphics, audio, and capacitive-touch human-machine interfaces. Typical applications include industrial sensor nodes, home automation controllers, portable data loggers, mTouch capacitive button/slider panels, low-cost graphics LCDs driven via PMP, and audio playback modules using external I2S codecs. The 28-SOIC wide-body footprint eases hand-soldering and rework for prototypes and small-batch industrial designs. When designing with this part, observe the recommended 22.05 µF or 10 µF input bulk decoupling near VDD/AVDD pairs plus 0.1 µF ceramic bypass capacitors; the device is sensitive to Vcore rail noise during high-speed Flash programming. The ICSP programming interface uses any PGECx/PGEDx pair, but each pair must be used as a matched pair. This page synthesizes distributor pricing, drop-in PIC32 family alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32MX120F032B-I/SP - 32-bit MCU 32KB Flash 40MHz SPDIP-28 | Microchip
PIC32MX120F032B-I/SP

PIC32MX120F032B-I/SP - 32-bit MCU 32KB Flash 40MHz SPDIP-28 | Microchip

The Microchip Technology PIC32MX120F032B-I/SP is a 32-bit RISC microcontroller based on the MIPS32 M4K core, delivering 40 MHz CPU performance with 32 KB Flash and 8 KB SRAM in a 28-pin SPDIP (Skinny Plastic Dual In-line Package) through-hole form factor. The device integrates two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripheral interfaces (timers, communication controllers, ADC) on a single silicon die. The PIC32MX family belongs to the 32-bit microcontroller hierarchy: 32-bit MCU -> MIPS M4K architecture -> PIC32 family -> PIC32MX1XX/2XX sub-family. The 28-pin SPDIP package places the part in the through-hole microcontroller category, favored for prototyping, educational, industrial, and ruggedized designs where leaded packages survive mechanical and thermal stress better than surface-mount equivalents. Key features include 40 MHz core with single-cycle multiply, hardware DMA for efficient data movement, 10-bit ADC with multiple input channels, 5-bit/10-bit PWM modules, two UART, two I2C, and two SPI/I2S interfaces. The PPS remapping block lets designers assign digital peripherals to almost any I/O pin, simplifying PCB layout and BOM reuse across PIC32 variants. The CTMU enables capacitive touch buttons, sliders, and proximity sensing without external analog components. The PIC32MX120F032B-I/SP consumes less than 0.5 mA/MHz active and supports multiple low-power sleep modes. Operating voltage is 2.3V to 3.6V, and the industrial temperature range spans -40C to +105C. The 28-SPDIP through-hole footprint suits breadboard, socketed, and hand-soldered designs that are impractical with QFN or QFP surface-mount variants. Typical applications include industrial control, USB device interfaces (with external transceiver), audio processing with I2S codecs, capacitive touch human-machine interfaces (HMIs), graphics interfaces via PMP, sensor fusion nodes, and educational/embedded development platforms. The PIC32 ecosystem is supported by MPLAB X IDE, Harmony v3 framework, and a broad library of code examples. Designers should note that the 28-SPDIP variant (SP suffix) is one of several pin-compatible package options for the PIC32MX120F032B silicon; SOIC, SSOP, and QFN variants share the same die and pinout but in different footprints. Verify package code carefully before PCB assembly. This page synthesizes distributor pricing, drop-in package alternatives, and application design notes beyond the manufacturer datasheet's bullet-list format to support faster component selection.

询价 联系我们
PIC32MX120F032B-V/ML - 32-bit MCU, 32KB Flash, 40MHz, 28-VQFN | Microchip
PIC32MX120F032B-V/ML

PIC32MX120F032B-V/ML - 32-bit MCU, 32KB Flash, 40MHz, 28-VQFN | Microchip

The Microchip Technology PIC32MX120F032B-V/ML is a 32-bit RISC microcontroller based on the MIPS32 M4K core, delivering up to 40 MHz performance with 32 KB Flash and 8 KB SRAM, housed in a 28-pin VQFN (ML) package (6x6 mm) with exposed thermal pad. It supports an operating voltage range of 2.3V to 3.6V and a temperature range of -40C to +105C (automotive/V-grade). What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, memory (Flash/SRAM), peripherals, and I/O on one die. The PIC32MX120 sits in the microcontrollers > 32-bit MCU hierarchy: 32-bit MCU -> RISC MCU -> PIC32 family -> PIC32MX1xx sub-family. The M4K core executes most instructions in one cycle and provides deterministic interrupt latency, distinguishing PIC32 from 8-bit PIC16/PIC18 families in throughput-sensitive embedded designs. Key features include 21 general-purpose I/O pins, two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders. Four DMA channels enable efficient peripheral-to-memory transfers without CPU intervention. Core current consumption is below 0.5 mA/MHz, supporting battery-powered applications. The device integrates a 10-bit ADC, multiple timers, and communication peripherals (UART, SPI, I2C, I2S, PMP). With PPS, peripheral functions can be remapped to many I/O pins, simplifying PCB layout. The CTMU module enables robust capacitive touch sensing with minimal external components. Typical applications include low-cost graphics interfaces, USB device/host bridges, audio processing with I2S codecs, capacitive touch panels, and industrial control panels. The 40 MHz CPU and DMA channels support real-time signal processing in embedded designs. A design consideration: this -V/ML variant is the V-grade (automotive temperature range) QFN package. Use adequate PCB thermal relief on the exposed pad. PPS must be configured at runtime; verify pin assignments against the chosen peripheral map to avoid conflicts. This page synthesizes distributor pricing, same-family drop-in alternatives, and application-specific design guidance not consolidated in the manufacturer datasheet, providing actionable reference data for embedded engineers.

询价 联系我们
PIC32MX120F032B-V/SS - 32-bit MCU 40MHz 32KB Flash | Microchip
PIC32MX120F032B-V/SS

PIC32MX120F032B-V/SS - 32-bit MCU 40MHz 32KB Flash | Microchip

The Microchip PIC32MX120F032B-V/SS is a 32-bit MIPS32 M4K RISC microcontroller operating at 40 MHz, integrating 32 KB of Flash and 8 KB of SRAM in a 28-pin SSOP package. Qualified to AEC-Q100 standards, this part supports an operating voltage range of 2.3 V to 3.6 V and an industrial/automotive temperature range of -40 °C to +105 °C, making it suited for harsh-environment embedded designs. A 32-bit microcontroller (MCU) is a single-chip processor that combines a CPU core, program memory, data memory, and a rich set of on-chip peripherals. The PIC32MX1xx/2xx family sits within the broader PIC32 architecture, which Microchip positions between 8-bit PIC MCUs and 32-bit ARM Cortex-M parts. Within the system hierarchy, the PIC32MX is a general-purpose microcontroller used in embedded control, sensor interfacing, and low-power connectivity. It is widely deployed in automotive body and HVAC modules, consumer appliances, and industrial control panels. Key features include less than 0.5 mA/MHz active current consumption, two I2S/SPI modules for audio codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, a Parallel Master Port (PMP) for graphics and external memory interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders. The device also integrates a 10-bit ADC, multiple UART/I2C/SPI peripherals, four DMA channels, and a real-time clock. The PIC32MX120F032B-V/SS uses a 5-stage pipelined MIPS32 M4K core with hardware multiply/divide, delivering 1.56 DMIPS/MHz performance. Compared to 8-bit PIC MCUs at the same clock, this gives roughly 10x more computational headroom. The combination of PPS, DMA, and CTMU lets a designer reduce external glue logic and keep the BOM compact for cost-sensitive applications. Typical applications include automotive HVAC and body controllers, capacitive touch user interfaces, low-cost graphical displays via PMP, USB-less audio accessories, and industrial sensor nodes. The AEC-Q100 qualification also makes it a candidate for in-cabin automotive HMI modules and small motor control boards. When designing with this MCU, plan I/O assignments early to take advantage of Peripheral Pin Select, since most digital peripherals can be remapped to a wide range of pins. The CTMU peripheral requires careful calibration of the constant-current source and the timing reference for reliable touch detection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond what is presented in the manufacturer datasheet.

询价 联系我们