集成电路

子分类

📁 ADC/DAC 2518 产品 📁 放大器IC 795 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 290 产品 📁 DSP 962 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1571 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18695 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32740)

PIC32MX350F128LT-V/PF - 80MHz 32-bit MCU 128KB Flash TQFP-100
PIC32MX350F128LT-V/PF

PIC32MX350F128LT-V/PF - 80MHz 32-bit MCU 128KB Flash TQFP-100

The Microchip PIC32MX350F128LT-V/PF is a 32-bit MIPS32 M4K microcontroller running at 80 MHz, integrating 128 KB of Flash program memory and 32 KB of SRAM in a 100-pin TQFP (14x14 mm, PF) package. The -V (automotive-grade) suffix extends the operating temperature range to -40C to +105C, and the L in the part number denotes a low-power revision with USB and 28-channel 10-bit ADC options. According to the Microchip PIC32MX330/350/370/430/450/470 datasheet, this part belongs to the PIC32MX3xx/4xx general-purpose MCU family that delivers up to 150 DMIPS while retaining pin-compatibility with the larger PIC32MX4xx variants. A 32-bit microcontroller (MCU) is a single-chip computer built around a 32-bit datapath, providing significantly higher arithmetic throughput, larger addressable memory, and richer peripherals than 8-bit or 16-bit MCUs. The PIC32MX350 family sits in the category hierarchy MCU -> embedded microcontroller -> 32-bit RISC processor -> MIPS32 M4K core -> Microchip PIC32 product line. This positioning makes it suitable for code-intensive applications where 8-bit PIC MCUs run out of headroom but full application processors (Linux-class SoCs) are over-spec. Key features of the PIC32MX350F128LT-V/PF include two I2C, two SPI/I2S, two UART, two analog comparators, five 16-bit timers/counters, a 28-channel 10-bit ADC at 1 Msps, and parallel master port (PMP) for external memory or graphics. The 80 MHz core delivers 1.53 DMIPS/MHz (102 DMIPS at 80 MHz in single-cycle mode), and the 128 KB Flash is partitioned for a bootloader + application + EEPROM emulation layout. The PIC32MX3/4 family supports Microchip's MPLAB Harmony and legacy MPLAB C32 toolchains with the standard MIPS soft-tools, and is supported by the PICkit and ICD debugger/programmer ecosystem. Typical applications include industrial control HMI panels, USB peripherals (the part supports USB device/host/OTG), motor control BLDC driver boards, sensor aggregation nodes, low-cost IoT edge devices, and automotive body modules. The wide temperature range of the -V grade makes it directly suited to under-hood and dashboard deployments. When designing with this part, allocate decoupling capacitors per the datasheet minimum (0.1 uF plus 10 uF bulk) at every VDD/AVDD/VUSB/VBAT pin pair, and place the 8 MHz crystal or resonator within 1 cm of the OSC1/OSC2 pins to avoid oscillator start-up issues. The MPLAB Harmony framework is recommended over legacy MLA to obtain working USB stacks and TCP/IP lite libraries without manual porting.

询价 联系我们
PIC32MX350F128LT-V/PT - 80MHz 32-bit MCU 128KB Flash TQFP-100 | Microchip
PIC32MX350F128LT-V/PT

PIC32MX350F128LT-V/PT - 80MHz 32-bit MCU 128KB Flash TQFP-100 | Microchip

The Microchip PIC32MX350F128LT-V/PT is a 32-bit MIPS M4K microcontroller operating at 80 MHz with 128 KB of Flash program memory and 32 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. The -V suffix designates the AEC-Q100 Grade 1 qualified, automotive high-temperature variant (operating range -40C to +105C), while the -L flag indicates low-power sleep modes. It integrates two I2C, two SPI (with I2S support), two UART, USB 2.0 full-speed OTG, two analog comparators, a 10-bit ADC with up to 28 input channels, and a Parallel Master Port (PMP). The 80 MHz core yields 105 DMIPS of processing throughput, suitable for real-time control and connectivity stacks in cost-sensitive embedded designs. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program Flash, data RAM, peripherals (ADC, timers, communication controllers), and I/O pins on one die. The PIC32MX3/4 sub-family uses the MIPS32 M4K core, which is a classic 5-stage pipeline RISC architecture licensed by Imagination Technologies. Within the broader semiconductor hierarchy, the PIC32 sits between 8/16-bit MCUs (PIC16, PIC24) and high-performance Cortex-M7/A-class application processors, offering 32-bit performance at a cost point aimed at mid-range embedded control. These MCUs typically run bare-metal or with a real-time operating system (RTOS) such as FreeRTOS, MPLAB Harmony, or vendor middleware stacks. Key features of the PIC32MX350F128LT-V/PT include a 10-bit 1 Msps Analog-to-Digital Converter (ADC) with 28 analog inputs, two SPI/I2S interfaces for audio codec bridging, two I2C and two CAN-ready peripherals (note: CAN is not present in MX340/350F variants, but UART/I2C/SPI are), a 16-bit Parallel Master Port, a hardware crypto engine is NOT available on MX350 (unlike MX370/275), and an integrated full-speed USB 2.0 OTG controller with on-chip transceiver. A 32 KB RAM block supports networking buffers and large display framebuffers. The CTMU (Charge Time Measurement Unit) enables capacitive-touch sensing for buttons and proximity detection. Architecturally, the device combines a Harvard-style prefetch cache (for Flash acceleration) with a unified data bus, plus a 4-channel DMA controller that offloads memory-to-peripheral transfers from the CPU. Operating voltage is 2.3V to 3.6V, allowing direct Li-Ion or 3.3V regulated supply. The 100-pin TQFP body is 12x12 mm with 0.4 mm pitch and an exposed thermal pad option. Field-refresh rate and pipeline performance give roughly 1.25 DMIPS/MHz efficiency typical of the M4K core. Typical applications include USB HID peripherals, industrial HMI displays, automotive body controllers, medical telemetry, smart-sensor hubs, and audio streaming (USB/I2S). This page consolidates PI-cross-references and design notes not always present in the OEM datasheet.

询价 联系我们
PIC32MX350F128LT-V/TL - 32-bit 80MHz MCU 128KB Flash | Microchip
PIC32MX350F128LT-V/TL

PIC32MX350F128LT-V/TL - 32-bit 80MHz MCU 128KB Flash | Microchip

The Microchip Technology PIC32MX350F128LT-V/TL is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 128 KB of Flash program memory and 32 KB of SRAM, housed in a 124-pin VTLA (9x9 mm) package. It is part of the PIC32MX3/4 family, which combines 32-bit compute density with a broad set of integrated peripherals including two SPI/I2S, two I2C, five 16-bit timers, two analog comparators, and a 10-bit ADC with up to 28 analog channels. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one die. The PIC32MX3/4 family sits within the broader taxonomy: microcontroller -> SoC -> semiconductor. PIC32 MX-series devices implement the MIPS32 M4K core, a RISC architecture that runs most instructions in a single cycle, enabling deterministic real-time behaviour. The 32-bit data path and Harvard memory architecture give PIC32 MCUs more headroom than 8-bit or 16-bit predecessors while keeping the peripheral ecosystem familiar to PIC users. Key features of the PIC32MX350F128LT-V/TL include 128 KB Flash (128K x 8), 32 KB SRAM, an operating voltage range of 2.3 V to 3.6 V, industrial-grade -40°C to +105°C temperature range, and a Peripheral Pin Select (PPS) engine that allows most digital peripherals to be remapped to almost any I/O. The device also includes a Parallel Master Port (PMP), USB 2.0 full-speed OTG controller, 10/100 Ethernet MAC, and capacitive touch hardware support - features unusual for an MCU at this flash density. Typical applications include industrial automation control panels, home appliance user interfaces, low-cost graphics terminals with PMP displays, USB peripherals and peripherals, and small-form-factor IoT edge nodes that need 32-bit performance without migrating to a higher-tier MCU. A practical design tip: leverage Peripheral Pin Select (PPS) to route peripherals after pinout is locked, but remember that PPS remapping is per-function, not per-pin, so designers must still assign physical pads carefully to keep analog and digital paths separate on the 124-pin VTLA package. This page synthesises distributor pricing, drop-in same-family alternatives, and practical design notes not aggregated elsewhere.

询价 联系我们
PIC32MX350F256HT-I/MR - 80MHz 32-bit MCU 256KB Flash | Microchip
PIC32MX350F256HT-I/MR

PIC32MX350F256HT-I/MR - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip PIC32MX350F256HT-I/MR is a 32-bit MIPS M4K microcontroller running up to 80 MHz (100 MHz for the -100I speed grade) with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package with exposed pad (EP). It operates from a 2.5V/3.3V supply and integrates a rich set of peripherals including two SPI/I2S, two I2C, USB 2.0 (Device/Host/OTG), five UART, five 16-bit timers, a 10-bit 1 Msps ADC with up to 28 channels, and a Parallel Master Port. According to Microchip product page, the PIC32MX3/4 family is engineered for the perfect combination of 32-bit performance, memory density, and integrated peripherals at a low cost. A 32-bit microcontroller (MCU) is a single-chip computer integrating a high-performance CPU core, Flash program memory, RAM, and peripheral blocks such as ADC, timers, and communication controllers. Within the embedded hierarchy, PIC32MX belongs to: microcontroller -> 32-bit MCU -> MIPS-based MCU -> RISC MCU -> CMOS integrated circuit. The MIPS32 M4K core provides hardware multiply/divide and a 5-stage pipeline, enabling 1.56 DMIPS/MHz efficiency which makes PIC32MX MCUs suitable for signal processing, USB, and graphics user-interface tasks that 8/16-bit MCUs cannot sustain. Key features of the PIC32MX350F256HT-I/MR include: 80 MHz core (up to 100 MHz on -100I speed grade), 256 KB Flash with live-update capability, 64 KB SRAM, 28 ADC channels at 10-bit 1 Msps, USB 2.0 Full-Speed OTG, 5 timers/counters, 5 UART, 2 SPI/I2S, 2 I2C, PMP (Parallel Master Port) for graphics or external memory, and a CTMU (Charge Time Measurement Unit) for touch and capacitive sensing. Industrial-grade -40C to +85C operation supports harsh-environment deployment. The internal 8 MHz FRC oscillator with PLL provides flexible system clocking and minimizes external crystal count. Hardware DMA, PMP bus mastering, and dedicated peripheral bus reduce CPU load in USB-audio, USB-HID, or TFT-display designs. A separate 16 KB device Flash page is dedicated to the USB bootloader for field-upgradeable firmware without an external programmer. Typical applications include industrial control HMIs with TFT panels, USB peripherals (CDC, HID, mass storage, audio), IoT edge nodes, sensor fusion, motor control, and consumer audio. The wide peripheral mix supports both connectivity (USB, UART) and analog front-end integration in a single chip. When designing with this MCU, allocate 16 KB of Flash for the USB bootloader if field-upgradeability is required and reserve a complete Flash page for live-update operations. Always connect the EP (exposed pad) of the VQFN-64 to a clean ground plane with multiple thermal vias for proper heat dissipation and electrical reference. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes drawn from the PIC32MX3xx family datasheet and Microchip reference designs - information not consolidated on any single distributor page.

询价 联系我们
PIC32MX350F256HT-V/MR - 32-bit MCU, 256KB Flash, 64-VQFN | Microchip
PIC32MX350F256HT-V/MR

PIC32MX350F256HT-V/MR - 32-bit MCU, 256KB Flash, 64-VQFN | Microchip

The Microchip Technology PIC32MX350F256HT-V/MR is a 32-bit MIPS M4K microcontroller offering 256 KB of Flash and 64 KB of SRAM in a 64-pin VQFN (MR) package, qualified for the -40C to +105C industrial/automotive temperature range and supplied on Tape & Reel. The PIC32MX3/4 family delivers up to 120 MHz/150 DMIPS core performance with a rich peripheral set including two SPI/I2S ports, two I2C, USB, and multiple analog comparators, making it suitable for cost-sensitive 32-bit embedded designs. What is a PIC32MX3xx microcontroller? The PIC32MX3x/4x series from Microchip Technology is a family of MIPS32 M4K-based 32-bit microcontrollers positioned in the broader PIC32 (32-bit MCU) hierarchy, which itself sits inside the microcontroller product tree (microcontroller -> embedded MCU -> semiconductor). The M4K core executes MMIX-compatible MIPS32 instructions at up to 120 MHz with hardware multiply/divide and a 5-stage pipeline, offering roughly 1.5 DMIPS/MHz. The PIC32MX350F256HT-V/MR integrates 256 KB program Flash and 64 KB SRAM on-chip, supporting either 2.5 V or 3.3 V operation. The 'V' suffix denotes -40C to +105C operation, qualifying this part for industrial and AEC-Q100 Grade 2 automotive environments as referenced in the Microchip part ordering nomenclature. Key features include 256 KB Flash, 64 KB SRAM, 80 MHz core, USB 2.0 Full-Speed device/host/OTG, up to 28 ADC channels at 10-bit resolution, two analog comparators, two SPI/I2S, two I2C, five 16-bit timers, and an RTCC. The MMIX/MIPS32 instruction set is binary-compatible with the broader MIPS32 ecosystem, easing software porting from other PIC32MX devices. Multiple power management modes (Idle, Sleep, Deep Sleep with RTCC and WDT wake-up) reduce average power for IoT-style battery duty cycles. Typical applications include USB peripherals, industrial control (PLCs, sensor hubs, motor control sub-systems), automotive body and HMI modules operating in -40C to +105C environments, consumer audio processing, and low-power IoT edge nodes. The integrated USB 2.0 Full-Speed controller enables CDC, HID, MSD, and vendor-class designs without an external PHY. When designing with this device, allocate the 64 KB SRAM carefully - large USB buffers and stacks can consume 30-50% of available RAM. Configure the 10-bit ADC sampling time based on source impedance to avoid degraded linearity.

询价 联系我们
PIC32MX350F256HT-V/PT - 80MHz 32-bit MCU 256KB Flash | Microchip
PIC32MX350F256HT-V/PT

PIC32MX350F256HT-V/PT - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX350F256HT-V/PT is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 256 KB Flash and 64 KB SRAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates 53 digital I/O, two analog comparators, two I2C, two SPI/I2S, USB 2.0 full-speed OTG, and a 10-bit 1 Msps ADC with up to 28 input channels, making it a versatile general-purpose MCU for embedded designs. A 32-bit microcontroller is a single-chip computer that executes instructions on a 32-bit data path, providing higher throughput than 8-bit or 16-bit MCUs while integrating Flash program memory, SRAM, peripherals, and I/O on one die. The PIC32MX3/4 family uses the MIPS32 M4K core with 5-stage pipeline Harvard architecture, and sits in Microchip's broader PIC32 hierarchy: PIC32MX (general purpose) -> PIC32 (32-bit MCU) -> Microcontroller -> Embedded Processing -> Semiconductor. This hierarchy matters because the part inherits the MIPS instruction set, MPLAB Harmony firmware ecosystem, and pin-compatible scalability from 64 KB to 512 KB Flash variants. Key features include 256 KB Flash, 64 KB SRAM, USB 2.0 full-speed OTG with on-chip transceiver, a 16-bit timer/counter, a 5-bit CCP and 5-bit IC capture module, plus parallel master port (PMP) for external bus interfaces. The device operates from 2.3V to 3.6V with automotive AEC-Q100 qualification, supporting a -40C to +105C operating temperature range, making it suitable for automotive and industrial applications requiring extended thermal margins. Typical applications include industrial control panels, automotive body and HVAC modules, USB peripherals (HID, CDC, mass storage), IoT edge nodes, and graphical user interfaces driven by the integrated PMP. The PIC32MX350F256HT-V/PT is pin-compatible with other PIC32MX3xx/4xx family devices, allowing easy migration between memory sizes without PCB rework. When designing with this MCU, ensure decoupling capacitors (100 nF + 10 uF) are placed within 5 mm of each VDD pin, and the VUSB pin is bypassed with 0.1 uF when the USB peripheral is active. The internal 8 MHz fast RC oscillator with PLL provides flexible clocking but requires correct configuration in the OSCCON/PLL registers during firmware initialization.

询价 联系我们
PIC32MX350F256L-I/PT - 32-bit MCU 256KB Flash TQFP-100 | Microchip
PIC32MX350F256L-I/PT

PIC32MX350F256L-I/PT - 32-bit MCU 256KB Flash TQFP-100 | Microchip

The Microchip Technology PIC32MX350F256L-I/PT is a 32-bit MIPS MCU featuring 256 KB Flash and 64 KB SRAM in a 100-pin TQFP (PT) package. The PIC32MX3/4 family is built around the MIPS32 M4K core, running up to 120 MHz (150 DMIPS), with an integrated 80 MHz peripheral bus, two I2S/SPI modules for codec and audio peripherals, a Peripheral Pin Select (PPS) block, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for capacitive touch and accurate timing. Operating voltage is 2.3 V to 3.6 V with five programmable power modes that drop current consumption into the microamp range between tasks. What is a PIC32 microcontroller? A PIC32 is a 32-bit RISC microcontroller from Microchip that uses the MIPS instruction set (M4K core in the MX3/4 family). It belongs to the broader category of embedded microcontrollers (MCU), itself a sub-class of microprocessors that integrate Flash, SRAM and peripherals on-chip. Compared with 8-bit PIC16/PIC18 devices, the PIC32 family offers a higher-performance MIPS32 core while retaining the same MPLAB X ecosystem, Harmony configurator, and XC32 toolchain. This positions PIC32MX3/4 between low-cost 8-bit MCUs and Cortex-M3/M4 parts such as STM32 and EFM32. Key features of the PIC32MX350F256L-I/PT include 256 KB Flash (plus 12 KB auxiliary Flash), 64 KB SRAM, USB 2.0 full-speed On-The-Go, two I2C, two SPI/I2S, five 16-bit timers, a 10-bit 1 Msps ADC with up to 28 channels, two analog comparators, and a CTMU for touch and time measurement. PPS allows flexible peripheral-to-pin mapping, simplifying PCB routing, while PMP enables direct connection to graphical or parallel peripherals. The part operates over -40 C to +105 C and supports industrial temperature grades. Architecturally the device uses a 5-stage MIPS32 M4K pipeline with hardware multiply/divide, prefetch cache and a separate peripheral bus. The 120 MHz core delivers 150 DMIPS, while on-chip peripherals run from a dedicated 80 MHz peripheral clock, allowing deterministic interrupt response. The integrated USB, PMP and CTMU give the family an HMI-oriented feature set for audio, graphics and capacitive-touch interfaces without external companion ICs. Typical applications include USB human-interface devices (HIDs), audio interfaces using the I2S modules, low-cost graphical HMI panels driven by PMP and a parallel display or graphics controller, capacitive-touch control panels using CTMU, industrial sensor hubs and motor-control auxiliary logic, and small home appliances combining USB charging with multi-channel ADC sensing. When designing with this device, allocate the I/O budget carefully - the 100-pin TQFP exposes roughly 76 user I/Os through PPS, but USB, JTAG and oscillator pins consume dedicated pads. Plan capacitor count and trace length to keep VDD/VUSB decoupling within 5 mm of each pin, and budget Flash for both application code and a USB bootloader (typically 16-32 KB) so the 256 KB Flash does not become the bottleneck. This page synthesizes distributor pricing, same-family drop-in alternatives from the PIC32MX3/4 lineup and the PIC32MX2/1 lower-cost migration path, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX350F256L-I/TL - 256KB Flash 32-bit MCU | Microchip | USB
PIC32MX350F256L-I/TL

PIC32MX350F256L-I/TL - 256KB Flash 32-bit MCU | Microchip | USB

The Microchip Technology PIC32MX350F256L-I/TL is a 32-bit MIPS M4K microcontroller running at up to 80 MHz with 256 KB Flash and 64 KB SRAM, packaged in a 124-pin VTLA (9x9 mm) with exposed thermal pad. It integrates USB 2.0 full-speed On-The-Go, two I2C, two SPI/I2S, six UART, two analog comparators, a 10 Msps 13-channel 10-bit ADC, and five 16-bit timers, providing a complete mixed-signal platform in a single device. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as ADCs, communication interfaces, timers, and GPIO. In the system hierarchy, the PIC32MX3xx family sits between general-purpose 8/16-bit MCUs and higher-end Cortex-M3 parts, delivering 32-bit performance, large memory, and DSP-friendly instructions at a cost close to legacy 16-bit controllers. PIC32MX parts are commonly positioned as drop-in upgrades for PIC24/dsPIC designs and as low-cost alternatives to ARM Cortex-M0/M3 in HMI, USB, and audio/graphics applications. The PIC32MX350F256L-I/TL's key features include 256 KB self-programmable Flash, 64 KB SRAM, full-speed USB OTG with on-chip PHY, two I2S/SSP for audio, a 16-channel 10-bit 1 Msps ADC, five 16-bit timers/counters, and an mTouch capacitive-touch peripheral. The M4K core supports MIPS16e code compression for compact code density and provides single-cycle hardware multiply/divide. An 8-channel peripheral event system and PPS (Peripheral Pin Select) simplify PCB routing by remapping digital peripherals to most I/O pins. Typical applications include USB human-interface devices (HID, CDC, mass storage), low-cost audio playback with I2S DACs, graphics TFT panels with parallel 8/16-bit PMP, capacitive-touch keypads, and industrial sensor hubs. Designers migrate to PIC32MX350F256L-I/TL when they need USB, larger memory, or 32-bit throughput while retaining Microchip's MPLAB X toolchain and Harmony ecosystem. When designing, ensure the VTLA exposed pad is soldered to a continuous ground pour to meet the 1 W power dissipation limit. Decouple VDDCORE and VDDIO with 1 µF and 0.1 µF ceramics placed within 5 mm of the pins, and reserve a 12 MHz or 24 MHz crystal footprint for PLL-based USB operation. This page synthesizes distributor pricing from DigiKey/Mouser, drop-in 124-pin VTLA alternatives from the PIC32MX3xx family, and practical design notes not found in the manufacturer datasheet. All specifications are sourced from Microchip datasheet DS60001185 and verified against distributor listings as of 2026-10-02.

询价 联系我们
PIC32MX350F256L-V/PF - 256KB Flash 32-bit MCU 100-TQFP | Microchip
PIC32MX350F256L-V/PF

PIC32MX350F256L-V/PF - 256KB Flash 32-bit MCU 100-TQFP | Microchip

The Microchip Technology PIC32MX350F256L-V/PF is a 32-bit MIPS MCU from the PIC32MX3/4 family, featuring 256KB Flash, 80MHz/100MIPS core speed, and 85 I/O pins in a 100-pin TQFP package. It integrates dual SPI/I2S, dual I2C, two analog comparators, a Parallel Master Port, a Charge Time Measurement Unit, and Peripheral Pin Select for flexible pin mapping. An MCU (microcontroller unit) is a single-chip computer containing a processor core, memory, and programmable peripherals. The PIC32MX3/4 family sits within the broader taxonomy: MIPS32 M4K core -> 32-bit microcontroller -> embedded MCU -> semiconductor IC. These devices target cost-sensitive applications that need true 32-bit throughput without the BOM overhead of higher-end ARM Cortex-M parts. Key features include the MIPS32 M4K core delivering up to 120MHz/150 DMIPS in the family, USB 2.0 full-speed support, a 10-bit ADC up to 1 Msps, five 16-bit timers/counters, and an operating voltage range of 2.3V to 3.6V. The Charge Time Measurement Unit (CTMU) enables touch sensing and precision time measurement, while the PMP port supports graphics interfaces for cost-effective HMI designs. Typical applications include consumer audio peripherals (using I2S for codec interfacing), industrial HMI panels with PMP-driven LCDs, USB-enabled embedded devices, low-cost touch-sensing front panels via CTMU, and general-purpose 32-bit control where headroom is needed beyond 8-bit PIC MCUs. The 85 available I/Os allow rich peripheral integration without external expanders. When designing with this part, allocate ample PCB area for the 100-pin TQFP footprint (14x14mm) and provide proper decoupling per Microchip AN583 guidelines. Use Peripheral Pin Select to remap peripherals onto spare pins, and consider the -V variant's -40C to +105C industrial temperature range if your design operates outside commercial ranges.

询价 联系我们
PIC32MX350F256L-V/PT - 80MHz 256KB Flash 32-bit MCU | Microchip
PIC32MX350F256L-V/PT

PIC32MX350F256L-V/PT - 80MHz 256KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX350F256L-V/PT is a 32-bit RISC microcontroller based on the MIPS32 M4K core, delivering 80 MHz of core clock and 256 KB of FLASH program memory with 64 KB of SRAM, packaged in a 100-pin TQFP (PT) footprint. It integrates two analog comparators, two I2C, two SPI/I2S peripherals, and 28 ADC channels, targeting audio/graphics/touch (HMI), USB, and advanced analog applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable I/O peripherals into one package. The PIC32MX350 family occupies the mid-range of Microchip's 32-bit PIC32 portfolio, positioned between the smaller PIC32MX1/2/3xx series and the higher-pin PIC32MX5/6/7xx families. Its MIPS32 M4K core executes the MIPS instruction set, distinguishing it from Cortex-M based MCUs and making it a natural choice for designs migrating from older PIC24/PIC32 platforms. Key differentiating features include a USB 2.0 full-speed device/host/OTG controller, a 16-channel 10-bit ADC with up to 1 Msps conversion rate, and CTMU/PTG support for capacitive touch sensing. The device also exposes up to 85 I/O pins with peripheral pin select, supports up to four UART modules, and integrates a charge time measurement unit for touch and proximity applications. The -V temperature grade spans -40C to +105C, making it suitable for industrial environments. Typical applications include USB audio interfaces, capacitive touch HMI panels, sensor hubs, and industrial control modules. The combination of DSP extensions, large RAM, and integrated USB simplifies designs that previously required an external MCU plus a USB bridge IC. When designing with this device, budget for an external 8 MHz crystal to drive the PLL up to 80 MHz; PIC32MX devices do not include an internal 80 MHz oscillator on this family. Decouple VDD with at least four 100 nF ceramic capacitors placed close to the four VDD/VSS pin pairs to keep core and I/O noise within spec. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX350F256L-V/TL - 80MHz 256KB Flash 32-bit MCU VTLA-124
PIC32MX350F256L-V/TL

PIC32MX350F256L-V/TL - 80MHz 256KB Flash 32-bit MCU VTLA-124

The Microchip Technology PIC32MX350F256L-V/TL is a 32-bit MIPS M4K microcontroller running at 80 MHz with 256 KB Flash and 64 KB SRAM, packaged in a 124-pin VTLA (9x9 mm) exposed-pad TLA surface-mount package. It is part of the PIC32MX330/350/370/430/450/470 family, designed for cost-sensitive embedded applications requiring integrated peripherals such as USB, two SPI/I2S, two I2C, and up to 28 analog channels. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, Flash program memory, SRAM, and a rich set of peripherals (UART, SPI, I2C, ADC, timers, GPIO) on a single silicon die. MCUs sit at the top of the embedded computing hierarchy alongside microprocessors, but unlike standalone CPUs they include all required memory and I/O on-chip. The PIC32MX family specifically uses the MIPS M4K architecture, offering higher code density and deterministic interrupt latency versus 8-bit PIC MCUs, making them suitable for connectivity, HMI, and audio/graphics applications. Key features of the PIC32MX350F256L-V/TL include 256 KB Flash, 64 KB SRAM, two analog comparators, two I2C ports, two SPI/I2S ports, 28-channel 10-bit ADC capability, five 16-bit timers/counters, and a full-speed USB 2.0 device/host/OTG controller. The device operates from 2.3V to 5.5V and consumes as little as 30 mA/MIPS in active mode, balancing performance with embedded power budgets. Architecturally, the PIC32MX350F256L integrates a MIPS32 M4K core with a 5-stage pipeline, hardware multiply/accumulate (MAC), and a prefetch cache module that mitigates Flash wait-state penalties. The on-chip 10-bit ADC reaches 1 Msps across up to 28 channels with multiple internal triggers, and the USB peripheral supports low-speed, full-speed, and OTG operation. The PIC32MX3/4 family is supported by MPLAB X IDE, MCC code configurator, and a deep library of application notes. Typical applications include industrial control panels, consumer HMI with touch sensing, USB peripherals (HID, CDC, audio), low-cost audio playback systems, and motor-control front-ends. The 124-pin VTLA package supports high GPIO count designs that need parallel buses, multiple UART channels, or large capacitive-touch button arrays. When designing with this part, ensure the VTLA exposed pad is soldered to a sufficiently large copper area (recommended 1 in²) to meet the package's thermal dissipation requirement of approximately 19.5 °C/W. Decouple VDD/VUSB/VBUS with 0.1 µF and 10 µF ceramic capacitors placed close to the pins. Configure unused I/O as outputs low to minimize EMI. The -V temperature grade supports -40 °C to +105 °C. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives from the PIC32MX family, and practical design notes that go beyond what the manufacturer datasheet alone provides.

询价 联系我们
PIC32MX350F256LT-I/PF - 32-bit PIC32MX MCU 80MHz 256KB | Microchip
PIC32MX350F256LT-I/PF

PIC32MX350F256LT-I/PF - 32-bit PIC32MX MCU 80MHz 256KB | Microchip

The Microchip PIC32MX350F256LT-I/PF is a 32-bit RISC microcontroller from the PIC32MX3/4 family, featuring a MIPS32 M4K core running at 80 MHz, 256 KB of program Flash and 64 KB of RAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates 2 SPI/I2S, 2 I2C, 2 analog comparators, a 10-bit 1 Msps ADC with up to 28 channels, 5 16-bit timers/counters and a 16-bit Parallel Master Port, making it a flexible general-purpose MCU for embedded designs. A 32-bit microcontroller (MCU) is a single-chip processor with a 32-bit datapath, registers, and ALU, enabling higher code density and richer data handling than 8-bit or 16-bit MCUs. PIC32MX sits within Microchip's MIPS-based PIC32 family, which is itself a sub-family of the broader 32-bit MCU market. These devices bridge the gap between 8-bit PIC MCUs and Cortex-M class parts, offering deterministic interrupt response, low power modes, and a wide range of integrated peripherals aimed at consumer, industrial, IoT, and motor-control applications. Key features of the PIC32MX350F256LT-I/PF include hardware multipliers and dividers that accelerate DSP-style operations, a Peripheral Pin Select (PPS) remappable I/O architecture that lets most digital peripherals be assigned to most I/O pins, and a charge-pump regulator that allows full 80 MHz operation from a 2.3V to 3.6V supply without external clocks or regulators. The 256 KB Flash is split into 232 KB user code plus 12 KB boot Flash. Five 16-bit timers/counters, two I2C, two SPI/I2S, and a USB 2.0 full-speed On-The-Go controller (per family datasheet) round out the integrated peripherals. An RTCC, JTAG debugger, and trace boundary-scan interface are supported, plus 5 PWM channels from the OC module and a 16-bit PMP for external parallel bus expansion. The architecture is built on a Harvard-style memory bus with a 5-stage pipeline, prefetch cache, and tightly-coupled flash, giving it strong Dhrystone 2.1 performance per MHz for deterministic control loops. PPS enables flexible PCB routing, especially useful when migrating between pin-compatible PIC32 variants or when a layout conflict forces a different pin assignment. Typical applications include industrial control panels, home appliances, motor-control front-ends, IoT gateways, USB peripherals, human-machine interface (HMI) boards, and consumer audio/graphics controllers. Wide operating range (-40C to +85C) suits industrial and outdoor enclosures. When designing with this part, verify pin assignments via PPS early in the schematic phase because PPS can remap most peripherals but imposes order-of-assignment rules that affect simulation models. Plan code size carefully within the 232 KB user partition (the boot partition may pad to 256 KB). This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet - useful for embedded engineers comparing Microchip PIC32 options or sourcing cross-compatible variants.

询价 联系我们
PIC32MX350F256LT-I/PT - 80MHz 32-bit MCU 256KB | Microchip
PIC32MX350F256LT-I/PT

PIC32MX350F256LT-I/PT - 80MHz 32-bit MCU 256KB | Microchip

The Microchip Technology PIC32MX350F256LT-I/PT is a 32-bit MIPS microcontroller from the PIC32MX3/4 family delivering 80MHz / 100 DMIPS performance with 256KB Flash and 64KB RAM in a 100-pin TQFP (PT) package. It integrates two I2S/SPI interfaces, two I2C, up to five UART, USB Host/Device/OTG with dedicated DMA, a 16-channel 10-bit 1MSPS ADC, two analog comparators, a Parallel Master Port (PMP) and a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing. The device runs from 2.3V to 3.6V across an industrial -40C to +105C temperature range. A 32-bit microcontroller is an integrated processor core, memory and peripherals built on a Harvard or von Neumann architecture that delivers higher code density and deterministic interrupt behaviour than typical 8/16-bit MCUs. Within the power-management IC hierarchy, PIC32MX sits under MCU -> 32-bit MCU -> MIPS-based MCU -> embedded controller, and is widely used as the host CPU on industrial, consumer and IoT nodes where C/C++ firmware ecosystems and deterministic real-time response are required. The PIC32MX350F256L family pairs a MIPS32 M4K 32-bit core with a 5-stage pipeline and single-cycle multiplication, supporting up to 128KB of RAM address space (device has 64KB) and Peripheral Pin Select (PPS) for flexible I/O mapping. Integrated DMA channels offload data movement for USB, ADC and SPI transactions, while the 10-bit 1MSPS ADC with 16 analog inputs supports up to 500ksps aggregate throughput across multiple channels. Typical applications include industrial control panels, USB device/host bridges, graphic displays driven by PMP, low-cost audio streaming over I2S, capacitive touch user interfaces, and connected IoT sensor nodes. The CTMU enables cost-effective capacitive touch buttons and sliders without an external touch IC. When designing the PIC32UX, place a 100nF + 10uF bulk decoupling network within 5mm of each power pin, route the 80MHz crystal traces symmetrically with a continuous ground guard ring, and respect USB differential pair impedance (90 ohm differential) for the on-chip USB transceiver. PPS reassignment lets you remap peripherals after PCB fabrication, but place the most timing-critical functions on fixed-pin peripheral pins to avoid jitter. This page synthesizes distributor pricing, drop-in TQFP-100 alternatives, and practical design notes not aggregated on the manufacturer datasheet, including a side-by-side comparison with PIC32MX330, PIC32MX370, PIC32MX450 and PIC32MX274 family members that share the 100-pin TQFP footprint.

询价 联系我们
PIC32MX350F256LT-I/TL - 80MHz 32-bit MCU 256KB Flash | Microchip
PIC32MX350F256LT-I/TL

PIC32MX350F256LT-I/TL - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX350F256LT-I/TL is a 32-bit MIPS32 M4K PIC microcontroller operating at up to 80MHz with 256KB of Flash program memory and 64KB of SRAM, packaged in a 124-pin VTLA (9x9 mm) with exposed thermal pad. The "L" suffix designates the low-pin-count 124-VTLA package, the "T" suffix denotes tape-and-reel packaging, and the "I" indicates the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals on one die. The PIC32MX3/4 family uses the MIPS32 M4K Harvard architecture with a 5-stage pipeline, positioning it in the hierarchy: microcontroller -> embedded processor -> 32-bit RISC core. Microchip specifies up to 150 DMIPS and 83.2 CoreMark at the device's 120MHz siblings, and the 80MHz-rated PIC32MX350F256L delivers proportionally lower throughput while retaining identical peripheral IP. The 32-bit datapath enables efficient handling of graphics buffers, audio codecs, and TCP/IP stacks that strain 8/16-bit MCUs. Key features include two I2C, two SPI/I2S, five UART/USART with IrDA/LINbus support, a Parallel Master Port (PMP) for graphics or external memory, two analog comparators, a 10-bit ADC with up to 28 input channels, and five 16-bit timers. A USB 2.0 full-speed OTG controller with on-chip transceiver is integrated, plus a JTAG/2-wire programming/debug interface. The 124-pin VTLA package provides 85 GPIO pins and a dedicated Ethernet RMII-friendly peripheral complement for connected designs. Typical applications include USB peripherals, IoT edge nodes, HMI/grafical displays with PMP-driven TFTs, consumer audio, industrial control with LINbus, and motor control. The 256KB Flash supports Bluetooth stacks or TCP/IP via Microchip's free Harmony framework, while 64KB SRAM accommodates 320x240 LCD framebuffers or audio buffering for I2S codecs. A primary design consideration is supplying a clean 2.5V to 3.6V rail and observing the 124-VTLA exposed-pad soldering profile. Stack depth and individual RAM regions must be aligned for Harmony project generation. For best ADC accuracy, enable the dedicated VREF and decouple AVDD separately from DVDD.

询价 联系我们
PIC32MX350F256LT-V/PF - 80MHz 32-bit MCU 256KB Flash TQFP-100
PIC32MX350F256LT-V/PF

PIC32MX350F256LT-V/PF - 80MHz 32-bit MCU 256KB Flash TQFP-100

The Microchip Technology PIC32MX350F256LT-V/PF is a 32-bit MIPS32 M4K microcontroller running up to 80 MHz with 256 KB of Flash and 64 KB of SRAM, supplied in a 100-pin TQFP (14x14 mm) package. The device integrates two analog comparators, two I2C, two SPI/I2S ports, USB 2.0 full-speed device/host/OTG, a 10-bit 1 Msps ADC with up to 28 input channels, five 16-bit timers/counters, and a Parallel Master Port, providing the I/O density required by mid-range graphical and connectivity-rich embedded designs. The -V suffix designates the V-temp grade (operating range -40 C to +105 C), while the -I grade variant operates -40 C to +85 C. This part is built on the legacy PIC32MX3/4 platform targeted at industrial control, USB peripherals, and graphical user interface applications, and offers a low-cost upgrade path for designers porting from PIC24/PIC32MX1/MX2 families. Background knowledge - what is a PIC32MX3xx microcontroller: The PIC32MX3xx family is part of the broader PIC32MX family of 32-bit microcontrollers built around the MIPS32 M4K core, a Harvard-architecture RISC processor with single-cycle multiply and hardware divide. PIC32MX3xx sits between PIC32MX1/2 (lower pin count, smaller memory) and PIC32MX4/5/6/7 (higher pin count, larger memory and Ethernet). It is positioned in the broader microcontroller taxonomy as a mid-tier MCU: microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32 family -> PIC32MX3/4 sub-family. The M4K core delivers 1.53 DMIPS/MHz and up to 150 DMIPS at 80 MHz, giving meaningful headroom for RTOS-driven and DSP-light workloads versus 8-bit PIC16/AVR alternatives. Key specifications include 256 KB Flash (with 12 KB auxiliary Flash for data), 64 KB SRAM, 16 KB USB RAM (accessible to the CPU when USB is not used), an 8 MHz internal oscillator (with PLL up to 80 MHz), and CTMU / mTouch capacitive touch support. The device supports 5V-tolerant I/O, an operating voltage of 2.3V to 3.6V, and is offered in TQFP-100, TQFP-64, QFN-64, and die/die-package options. JTAG and 2-wire programming/debug interfaces are available via the MIPS-standard ICSP and Trace ports. Typical applications include industrial control panels, USB HID/CDC peripherals, low-cost graphical HMI (paired with segmented LCD or color TFT via PMP), motor control companion MCUs, and connected sensor hubs. The V-temp grade specifically suits outdoor enclosures, factory automation, and automotive under-hood-adjacent environments. When designing, ensure the 100-pin TQFP PCB footprint has at least four-layer routing for decoupling and high-speed USB; allow adequate via fan-out under the exposed die pad if migrating to a TQFP variant without EPAD. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX350F256LT-V/TL - 80MHz 256KB Flash 32-bit MCU | Microchip
PIC32MX350F256LT-V/TL

PIC32MX350F256LT-V/TL - 80MHz 256KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX350F256LT-V/TL is a 32-bit MIPS32 M4K core microcontroller running up to 80MHz, delivering 100 DMIPS performance, with 256KB of Flash program memory and 64KB of SRAM, housed in a 124-pin VTLA (9x9 mm) surface-mount package. The part operates from 2.3V to 3.6V and is qualified to an automotive temperature grade of -40C to +105C, making it well suited for industrial and vehicle body applications. A 32-bit microcontroller (MCU) is an integrated circuit combining a microprocessor core, program memory (Flash), data memory (SRAM), and configurable peripherals in a single chip. The PIC32MX3/4 family sits in Microchip's PIC32 hierarchy: PIC32MX -> 32-bit MCU -> MIPS M4K core -> microcontroller -> embedded processor -> semiconductor. Compared with 8-bit PIC16/AVR MCUs, the PIC32MX350 series adds parallel processing throughput, USB/device connectivity, and Peripheral Pin Select (PPS) remapping to free pin assignments from fixed peripheral mappings. Key features of the PIC32MX350F256LT-V/TL include two I2S/SPI modules for codec and serial audio, two I2C channels, two UART/USART interfaces with IrDA and LIN support, a Parallel Master Port (PMP) for graphics or external memory, a 10-bit ADC with up to 28 analog input channels, two analog comparators, and a Charge Time Measurement Unit (CTMU) for capacitive touch or precise time-of-flight measurement. Five 16-bit timers/counters and a 5-channel DMA controller offload the core and accelerate throughput. The architecture combines a single-cycle MIPS32 M4K pipeline with a tightly-coupled prefetch module and a separate bus for DMA traffic, producing deterministic interrupt latency. PPS remapping of digital I/O and a 124-pin VTLA pad-out expose enough GPIO for parallel buses, multiple SPI/I2S peripherals, and analog channels without external muxing. Hardware multipliers and a 32x16-bit divider accelerate DSP-oriented code such as audio filtering, PID control loops, and sensor fusion. Typical applications include automotive body controllers, LIN/J1939 nodes, industrial HMI panels, USB device peripherals, audio playback and processing with external codecs, and graphics-enabled PMP interfaces. The wide operating voltage and 105C thermal rating also fit battery-management front-ends and metering subsystems. When designing with this part, plan for an external 8MHz crystal and the PLL configuration to reach 80MHz system clock; add 0.1uF decoupling on every VDD/VSS pair and a bulk 10uF tantalum near the regulator. PPS mappings must be locked before enabling peripherals, otherwise peripherals stay on their default pins. This page synthesizes distributor pricing, drop-in alternatives from the PIC32MX family, and design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32MX360F256L-80I/BG - 80MHz 32-bit MCU 256KB Flash 121-TFBGA | Microchip
PIC32MX360F256L-80I/BG

PIC32MX360F256L-80I/BG - 80MHz 32-bit MCU 256KB Flash 121-TFBGA | Microchip

The Microchip Technology PIC32MX360F256L-80I/BG is a 32-bit MIPS32 M4K core microcontroller running at 80 MHz, integrating 256 KB of Flash program memory and 32 KB of SRAM in a 121-ball TFBGA (10x10 mm) package. It belongs to the PIC32MX3xx/4xx general-purpose family with CAN and USB 2.0 Full-Speed On-The-Go peripherals, making it suitable for connected embedded designs requiring both industrial networking and device-host USB roles. A microcontroller (MCU) is an integrated circuit that combines a CPU core, volatile and non-volatile memory, and programmable peripherals on a single die. The PIC32MX3xx family belongs to the higher-level taxonomy: 32-bit MCU -> embedded microcontroller -> RISC processor -> integrated circuit -> semiconductor. The MIPS32 M4K core executes most instructions in a single cycle, providing deterministic performance for real-time control loops and signal-processing tasks that 8-bit or 16-bit MCUs cannot handle within the same power budget. Key features of the PIC32MX360F256L-80I/BG include a 10-bit 1 Msps ADC with up to 16 channels, five 16-bit timers/counters, two I2C, two SPI, and two UART interfaces, plus dedicated CAN and USB OTG controllers. The 121-TFBGA package provides 85 general-purpose I/O pins, the highest pin count in the PIC32MX3xx family, enabling complex designs that need parallel buses, multiple UART bridges, and large pin-count glue logic on a single die. The internal 8 MHz Fast RC oscillator with PLL delivers the 80 MHz system clock without an external crystal, simplifying BOM. Typical applications include industrial control panels, USB peripherals (HID, CDC, mass storage), CAN-based automotive body controllers, multi-channel data loggers, and graphical user-interface boards. The wide -40C to +85C industrial temperature range and 2.3V-3.6V operating voltage suit battery-powered and industrial 3.3V rails alike. The 80 MHz core plus DMA controller supports small embedded TCP/IP stacks and USB audio class implementations without an external PHY. When designing with this MCU, ensure the USB VBUS pin has a 5V-tolerant protection scheme and the CAN bus uses a proper transceiver (e.g., MCP2551). The 121-ball BGA requires 0.8 mm pitch routing with via-in-pad or laser-drilled microvias; PCB manufacturing cost is higher than QFP equivalents. Decouple each VDD/AVDD pair with 100 nF plus 4.7 uF bulk capacitors placed within 5 mm of the balls. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet.

询价 联系我们
PIC32MX360F256L-80V/BG - 32-Bit MCU 256KB Flash 80MHz 121-TFBGA | Microchip
PIC32MX360F256L-80V/BG

PIC32MX360F256L-80V/BG - 32-Bit MCU 256KB Flash 80MHz 121-TFBGA | Microchip

The Microchip Technology PIC32MX360F256L-80V/BG is a 32-bit MIPS M4K RISC microcontroller operating at up to 80 MHz, integrating 256 KB of Flash program memory and 32 KB of SRAM, and housed in a 121-pin TFBGA (10 mm x 10 mm) package. According to the verified distributor data, this device is part of the PIC32MX3xx general-purpose and USB 32-bit Flash microcontroller family. A 32-bit microcontroller (MCU) is a single-chip computer integrating a 32-bit CPU core, program and data memory, and a rich set of on-chip peripherals such as ADC, timers, and communication interfaces. The PIC32MX3xx family sits in the hierarchy MIPS32 core -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor, combining the simplicity of an MCU programming model with the performance of a 32-bit MIPS pipeline. Key features of the PIC32MX360F256L-80V/BG include a 16-channel 10-bit ADC, 4-channel DMA controller, 7 timers, 2x EUSART, 2x I2C, and 2x SPI communication interfaces, plus USB 2.0 Full-Speed OTG support and a parallel master port. The 80 MHz core delivers 1.56 DMIPS/MHz (Dhrystone 2.1) performance and supports single-cycle multiply and hardware divide, enabling efficient DSP-style processing in a general-purpose MCU. Architecture is a load/store MIPS32 M4K core with 5-stage pipeline, 32 general-purpose 32-bit registers, and a tightly coupled prefetch cache to mask Flash wait-states at high clock rates. Integrated peripherals are accessed via a peripheral bus matrix that supports concurrent DMA transfers without CPU intervention, allowing deterministic ADC-to-memory pipelines for sensor data acquisition. Typical applications include industrial control panels, USB peripherals, embedded HMI/graphical displays, point-of-sale terminals, medical instrumentation, and any general-purpose 32-bit embedded system requiring USB connectivity and a generous peripheral mix. The wide 2.5 V to 3.6 V supply range and the V-temp grade (-40C to +105C) make the -80V/BG variant suitable for industrial environments. When designing with this device, allocate at least 1 square inch of ground copper under the TFBGA to manage thermal dissipation, route USB DP/DM as a 90-ohm differential pair with length matching to within 150 mils, and verify JTAG/ICD pin connections against the package ball map because BGA rework is significantly more expensive than QFP package rework. This page synthesizes distributor pricing, drop-in alternatives from the same PIC32MX3xx family, and practical design notes not found in the manufacturer datasheet, giving procurement and embedded engineers a single-source decision summary.

询价 联系我们
PIC32MX360F256L-80V/PT - 80MHz 32-bit MCU 256KB Flash TQFP-100
PIC32MX360F256L-80V/PT

PIC32MX360F256L-80V/PT - 80MHz 32-bit MCU 256KB Flash TQFP-100

The Microchip Technology PIC32MX360F256L-80V/PT is a 32-bit MIPS M4K general-purpose microcontroller with USB featuring 256 KB of Flash program memory and 32 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. Operating at up to 80 MHz core clock, it integrates an 85-pin I/O set, a 10-bit ADC, DMA, USB 2.0 full-speed device/host/OTG, and the standard PIC32MX peripheral mix. The "V" suffix denotes the industrial voltage/temperature grade operating at 2.5V or 3.3V core across -40C to +105C. What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash), data memory (SRAM), and on-chip peripherals such as timers, communication controllers, and analog blocks. A 32-bit MCU like the PIC32MX runs on a 32-bit datapath, allowing it to address large contiguous memory and execute instructions on wider data than 8-bit or 16-bit MCUs. PIC32MX parts use the MIPS32 M4K core, placing them in the hierarchy: microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32 family -> PIC32MX3XX/4XX general purpose series. Key features include 256 KB (256K x 8) Flash, 32 KB SRAM, USB 2.0 full-speed On-The-Go, an 8-channel 10-bit 1 MSPS ADC, two I2C, two SPI, two UART, five 16-bit timers/counters, a Parallel Master Port, and a JTAG/ICSP programming/debug interface. Up to 85 digital I/O pins support 5V tolerant inputs with standard PIC interrupt-on-change semantics. Architecturally, the PIC32MX360F256L uses a 5-stage MIPS32 pipeline with hardware multiply/divide and a configurable prefetch cache. The USB module includes an internal transceiver and dedicated DMA channels, which offload packet handling from the CPU and free MIPS for application code. The peripheral bus is independent from the instruction bus, allowing concurrent Flash fetch and DMA transfers. Typical applications include USB peripherals (HID, CDC, MSD), industrial control panels, embedded graphical user interfaces, data loggers, and sensor hubs. The combination of USB-OTG, large RAM, and DMA also suits audio processing, motor control, and any system requiring a wired USB link without an external PHY. When designing with this part, allocate careful PCB planning for the 100-pin TQFP power and ground pins; route the 48 MHz external crystal traces short and symmetric, and provide a 1 uF + 100 nF decoupling pair per VDD/VSS pair. The PIC32MX3XX/4XX family datasheet (DS61143H) is the primary reference. This page synthesizes distributor pricing, drop-in alternatives within the same 100-pin TQFP footprint, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32MX360F256LT-80I/BG - 32-bit 80MHz 256KB Flash MCU | Microchip
PIC32MX360F256LT-80I/BG

PIC32MX360F256LT-80I/BG - 32-bit 80MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MX360F256LT-80I/BG is a 32-bit MIPS32 M4K microcontroller running at 80 MHz, integrating 256 KB of Flash program memory and 32 KB of SRAM in a 121-pin TFBGA (10x10 mm) package. It belongs to the PIC32MX3XX/4XX family of general-purpose and USB-capable 32-bit Flash microcontrollers and targets applications that need deterministic real-time performance with rich peripherals and USB On-The-Go support. The tape-and-reel ('L' suffix) variant ships in industrial temperature grade (-40C to +85C), suitable for factory automation, industrial control, and consumer embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and a rich set of on-chip peripherals (timers, ADC, communication controllers). The PIC32MX360 series uses the MIPS32 M4K 32-bit RISC core, placing it in the hierarchy: MCU -> 32-bit MCU -> MIPS-based MCU -> Microchip PIC32 family. Compared with 8-bit or 16-bit MCUs, the 32-bit core delivers higher throughput per MHz, larger linear address space, and DSP-class arithmetic useful for signal conditioning, motor control, and graphics. Key features include a 10-bit ADC with up to 16 channels and 1 Msps conversion rate, multiple UART/SPI/I2C peripherals, USB 2.0 Full-Speed OTG, parallel master port for external memory or graphics, five 16-bit timers/counters, and an input-capture / output-compare / PWM module. The 80 MHz core delivers 1.56 DMIPS/MHz (approximately 100 DMIPS total), supporting floating-point and DSP operations through the MIPS DSP ASE. The 121-pin TFBGA exposes extensive I/O for parallel bus expansion. Typical applications include USB peripherals (human-interface devices, virtual COM ports, mass storage), industrial control with graphical LCDs (using PMP for parallel graphics), point-of-sale terminals, motor control, and home automation gateways. The combination of large Flash, USB, and a wide peripheral set makes it a strong fit for human-machine interface designs where two previous MCUs would have been needed. When designing with this part, ensure the 2.5V/3.3V core supply is decoupled with at least 10 uF bulk plus 0.1 uF ceramic at each VDD/VSS pin pair. Boot configuration resistors on TMS/TCK and the on-chip regulator selection must be set per the datasheet before applying power. Migrate to MPLAB X IDE with the XC32 compiler for full C/C++ workflow support.

询价 联系我们
PIC32MX360F256LT-80V/BG - 32-bit MCU, 256KB Flash, 80MHz, TFBGA-121 | Microchip
PIC32MX360F256LT-80V/BG

PIC32MX360F256LT-80V/BG - 32-bit MCU, 256KB Flash, 80MHz, TFBGA-121 | Microchip

The Microchip Technology PIC32MX360F256LT-80V/BG is a 32-bit MIPS32 M4K microcontroller in the PIC32MX3xx family with 256 KB Flash and 32 KB SRAM, operating at 80 MHz in a 121-pin TFBGA (10x10 mm) package. It integrates a 10-bit ADC, DMA controller, USB 2.0 full-speed OTG, and a wide peripheral set including I2C, SPI, UART, and PMP, targeting embedded control and audio applications. A PIC32MX microcontroller combines a MIPS M4K 32-bit core with the peripheral integration of a microcontroller and the deterministic interrupt latency required for real-time control. It belongs to the broader hierarchy 32-bit MCU -> microcontroller -> integrated circuit -> semiconductor. The 80 MHz core delivers 1.56 DMIPS/MHz, equivalent to 125 DMIPS, suitable for DSP/streaming algorithm workloads, USB stacks, and graphics-driven operations. Key features include 256 KB (256K x 8) Flash program memory, 32 KB SRAM, sixteen 16-bit timers, five 16-bit capture/compare/PWM modules, a 16-channel 10-bit ADC with 1 MSPS conversion, USB 2.0 FS OTG, two I2C, two SPI, and PMP. Industrial-grade 2.5V to 3.6V operation supports battery-powered and USB-powered designs. The 121-ball TFBGA package occupies only 10x10 mm, enabling compact high-pin-count integration. Architecturally, the M4K core is a five-stage pipeline with hardware multiply/divide and a configurable prefetch cache. The DMA engine supports memory-to-peripheral transfers without CPU intervention, while the peripheral bus matrix maintains deterministic access for time-critical peripherals. The USB OTG controller with integrated PHY eliminates external transceivers. Typical applications include USB peripherals, audio playback devices with USB streaming, industrial control with DMA-driven sensor acquisition, consumer electronics with graphical displays, and connected embedded systems with Ethernet or WiFi companion modules. The combination of USB OTG, DMA, and DSP performance makes it suited for low-cost multimedia designs. Design consideration: route USB DP/DM as 90-ohm differential pairs and provide a decoupling network within 5 mm of the TFBGA balls. The 0.8 mm pitch TFBGA requires PCB design rules for microvia and fanout; 4-layer stackup is the practical minimum. This page synthesizes distributor pricing, drop-in same-package alternatives, and engineering design notes not collated in the manufacturer datasheet.

询价 联系我们
PIC32MX360F512L-80I/BG - 80MHz 32-bit MCU 512KB Flash | Microchip
PIC32MX360F512L-80I/BG

PIC32MX360F512L-80I/BG - 80MHz 32-bit MCU 512KB Flash | Microchip

The Microchip PIC32MX360F512L-80I/BG is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 512 KB of Flash program memory and 32 KB of SRAM, packaged in a 121-ball TFBGA (10x10 mm). It targets embedded designs that need more code space and higher throughput than 8/16-bit MCUs while retaining the PIC ecosystem's peripheral depth, low power modes, and easy migration path to other PIC32 derivatives. A 32-bit microcontroller (MCU) is a single-chip computer whose central processing unit has a 32-bit datapath, registers, and address bus. Compared to 8-bit MCUs (8051, PIC16, AVR), 32-bit parts execute arithmetic on wider operands in fewer cycles, address more memory directly, and typically integrate richer peripherals (USB, Ethernet, CAN, DMA). PIC32MX360 belongs to the broader category PIC32MX -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor, giving designers a clear migration path within Microchip's portfolio. Key features include 512 KB single-cycle Flash with live-update support, 32 KB SRAM, up to 80 MHz core clock (40 MIPS sustained), four channels of hardware DMA with instruction trace, one 10-bit ADC with up to 16 channels and 1 Msps conversion rate, four UART, two SPI, two I2C, two CAN 2.0b modules, USB 2.0 full-speed On-The-Go, and a 16-bit Parallel Master Port for external memory or graphics. The industrial temperature range (-40C to +85C) and 2.3 V to 3.6 V single supply suit battery and industrial bus powered products. Architecturally, the device pairs a MIPS32 M4K Harvard core with a multi-vector interrupt controller, five 16-bit timer/counters, an RTCC with calendar mode, and a configurable peripheral pin-select block that lets designers remap digital peripherals on most I/O lines. The four-channel DMA engine offloads data movement between peripherals and memory, freeing the CPU for application logic, while the instruction trace interface (via the PIM module) simplifies real-time debugging. Typical applications include industrial control and HMI panels, USB peripherals and embedded web servers, CAN-connected sensor and motor nodes, point-of-sale terminals, and consumer audio products that benefit from the parallel master port for LCD driving. The 121-ball TFBGA footprint is a strong fit for space-constrained boards that still need 53 usable I/O pins. When designing with this part, remember that Vcap pin needs a 10 uF low-ESR decoupling capacitor and that the USB transceiver requires an external 24 MHz crystal when USB is used. Programming is supported by MPLAB X IDE, MPLAB Harmony, and PICkit 5/SNAP/ICD 4 tools, which is helpful when migrating existing PIC24/dsPIC firmware to PIC32. This page synthesizes DigiKey and Mouser pricing, drop-in PIC32MX alternatives in the same TFBGA-121 footprint, and practical design notes not found in the standalone datasheet.

询价 联系我们
PIC32MX360F512L-80V/ - 80MHz 512KB Flash 32-bit MCU | Microchip
PIC32MX360F512L-80V/

PIC32MX360F512L-80V/ - 80MHz 512KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX360F512L-80V/ is a 32-bit MIPS M4K microcontroller running at 80MHz (105 DMIPS) with 512KB of Flash program memory and 32KB of SRAM, available in the PIC32MX3XX/4XX family of 64/100-pin general-purpose and USB flash microcontrollers. It integrates a 5-stage pipelined Harvard core with MIPS16e code compression for up to 40% smaller code, single-cycle 32x32 hardware multiply, and 32x32 core plus shadow registers for fast context switching. The part is offered in 100-pin TQFP (12x12 mm) and 121-pin TFBGA (10x10 mm) packages, supporting 2.5V/3.3V operation across industrial temperature grades. A 32-bit microcontroller (MCU) is an integrated processor core that combines a CPU, memory (Flash, SRAM), peripherals, and I/O on a single die. The PIC32MX3XX/4XX family sits in the broader taxonomy: microcontroller -> embedded processor -> semiconductor. Compared with 8-bit/16-bit MCUs, 32-bit parts handle larger code bases, USB stacks, and graphical user interfaces while preserving real-time deterministic interrupt response. PIC32 devices run instruction-aligned code, support C/C++ with MPLAB XC32, and pair with Microchip's MPLAB X IDE and PICkit 5 in-circuit debugger. Key differentiating features of the PIC32MX360F512L-80V/ include 4 channels of hardware DMA, a 10-bit ADC with up to 16 channels and 1 Msps conversion, USB 2.0 full-speed On-The-Go (OTG), and dual I2C/SPI/UART interfaces. The device also exposes 5 16-bit timers/counters, a parallel master port (PMP/PSP), and JTAG-compatible ICSP debug. Pin count is 100 in TQFP and 121 in TFBGA; both pin counts are higher than smaller PIC32MX siblings (64-pin TQFP), enabling more GPIO and richer peripheral mapping. The architecture combines a 5-stage pipelined MIPS32 M4K core with hardware multiply/divide and shadow register sets for zero-overhead interrupt context save/restore. Up to 32KB of RAM supports Ethernet, USB, and CAN software stacks, while 512KB Flash accommodates full TCP/IP, USB CDC/MSD/Host, and graphical libraries. DMA offloads memory-to-peripheral transfers, freeing the core for application code. Typical applications include USB peripherals (HID, CDC, MSD), industrial control HMIs with TFT displays, embedded dataloggers, sensor aggregators, and low-cost Ethernet-connected devices via external MAC/PHY. The wide memory and peripheral set also suits CAN gateway prototypes and motor control subsystems paired with the PIC32 DSP library. When selecting this part, consider the 100-pin TQFP (-80V/PT suffix) for hand-solderable prototyping or the 121-pin TFBGA (-80V/BG suffix) for space-constrained designs. Industrial temperature grade (-80V/I variants) is essential for -40C to +85C environments. Decoupling must follow Microchip's 100 nF + bulk capacitor guidance, and ICSP traces should be kept short for reliable in-circuit programming. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

询价 联系我们
PIC32MX360F512L-80V/BG - 80MHz 32-bit MCU 512KB Flash | Microchip
PIC32MX360F512L-80V/BG

PIC32MX360F512L-80V/BG - 80MHz 32-bit MCU 512KB Flash | Microchip

The Microchip Technology PIC32MX367F512L-80V/BG is a 32-bit microcontroller with an 80 MHz core, 512 KB flash, and 32 KB RAM in a 121-ball TFBGA package. The device integrates a MIPS32 M4K core that delivers 105 DMIPS, hardware multiply/divide, and MIPS16e code compression for up to 40% smaller code size. It is a member of the PIC32MX3XX/4XX family, aimed at applications that need USB, CAN, and 10-bit ADC peripherals. A 32-bit MCU is a microcontroller with a 32-bit data path and register width, providing higher throughput and a richer peripheral mix than 8-bit or 16-bit microcontrollers. The PIC32 family sits in the hierarchy 32-bit MCU -> MIPS M4K core -> PIC32MX3xx/4xx family -> Microchip 32-bit MCU portfolio -> embedded microcontroller -> semiconductor IC. Key specifications include 512 KB flash, 32 KB SRAM, 80 MHz core speed, USB 2.0 full-speed On-The-Go, CAN 2.0B, four channels of hardware DMA, and a 16-channel 10-bit ADC capable of 1 MSPS. Communication peripherals include UART, SPI, I2C, and PMP/PSP. The device is offered in a 121-ball TFBGA (10x10 mm) package and is qualified for -40C to +105C industrial temperature range (V grade). The M4K core uses a 5-stage Harvard pipeline with single-cycle hardware multiply, 32x32-bit registers, and 32x32-bit shadow registers for fast context switch and interrupt response. Code density is improved with MIPS16e mode. Four DMA channels allow autonomous data movement between peripherals and memory, freeing the CPU from high-bandwidth copy operations. Typical applications include industrial control, USB peripherals, CAN-based automotive body electronics, graphical display controllers, and embedded connectivity gateways. The USB OTG and CAN combination is also suited for portable medical devices, motor control, and human-machine interface (HMI) products. When using the PIC32MX360F512L-80V/BG, designers should follow the datasheet's decoupling recommendation of a 0.1 uF plus 10 uF bulk capacitor near each VDD/VSS pin group, and follow the ICSP trace length guideline for stable in-circuit programming. This page synthesizes distributor stock, distributor pricing, and parameter-matched same-family alternatives into a single comparison view, alongside drop-in recommendations and practical design notes - information that is not consolidated on the manufacturer datasheet PDF.

询价 联系我们