集成电路

子分类

📁 ADC/DAC 2518 产品 📁 放大器IC 795 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 290 产品 📁 DSP 962 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1571 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18695 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32740)

TJA1049T/1Z - High-Speed CAN Transceiver with Standby | NXP
TJA1049T/1Z

TJA1049T/1Z - High-Speed CAN Transceiver with Standby | NXP

The NXP TJA1049T/1Z is a high-speed Controller Area Network (CAN) transceiver providing the physical interface between a CAN protocol controller and the two-wire CAN bus, housed in an 8-pin SOIC package. The TJA1049T variant is specified for 5V microcontroller supply rails, supports data rates up to 1 Mbit/s, and includes a low-current Standby mode with remote bus wake-up capability. The device implements the ISO 11898-2:2003 and ISO 11898-5:2007 physical layer standards and is qualified for the pending updated ISO 11898-2:2016 release. A CAN transceiver is a physical-layer interface IC that translates the digital transmit/receive signals of a CAN protocol controller into the differential voltage levels (CANH/CANL) defined by ISO 11898-2 on the bus, while also providing bus-side ESD protection and dominant/recessive arbitration. As an interface IC the TJA1049T/1Z sits between application-layer MCU/processor and the physical CAN bus, making it a foundational building block for in-vehicle networking, industrial automation and any system requiring robust differential serial communication. Key features include a very low quiescent current in Standby mode for battery-powered nodes, a SPLIT output for stabilizing the recessive common-mode voltage in networks with multiple unpowered nodes, and transmit data (TXD) dominant time-out protection that prevents the bus from being permanently clamped if the controller fails. The integrated bus wake-up filter rejects transients on CANH/CANL to ensure false wake-ups do not discharge the battery in automotive quiescent scenarios. Typical applications include automotive body and chassis ECUs, CAN-based powertrain nodes, industrial CANopen and DeviceNet modules, and any 5V microcontroller host that requires a compact, low-power standby-enabled physical-layer interface. Designers often pair the TJA1049T/1Z with 5V MCUs such as the NXP S12K or ST STM32 families, plus a 5V LDO and common-mode choke for EMI hardening. When designing with this part, observe the bus termination: 120 ohm resistors at each network end with optional split termination for better EMC performance. Decouple VCC with 100 nF ceramic close to the pin and provide a robust PCB ground return for the bus ESD clamps to operate as specified.

询价 联系我们
TJA1049T/3J - 3-5V High-Speed CAN Transceiver | NXP
TJA1049T/3J

TJA1049T/3J - 3-5V High-Speed CAN Transceiver | NXP

The NXP TJA1049T/3J is a high-speed CAN transceiver with integrated standby mode for connecting a CAN protocol controller to a physical two-wire CAN bus. It supports direct interfacing with microcontrollers operating from 3 V to 5 V and implements CAN physical-layer requirements identified by NXP with ISO 11898-2:2003, ISO 11898-5:2007, and the pending updated ISO 11898-2:2016 version. The device is supplied in an 8-pin SOIC package. A CAN transceiver is an interface IC that bridges a host controller and a differential communication bus. The CAN controller generates and interprets CAN frames, while the transceiver converts those digital signals into robust differential bus levels and converts received bus levels back into logic-compatible signals. In the hierarchy of electronic components, the TJA1049T/3J belongs to the CAN interface and physical-layer transceiver class, within interface ICs and networking semiconductors. The principal verified features include a 3 V to 5 V microcontroller-interface range, high-speed CAN operation, differential transmit and receive capability, standby support, and compatibility with the CAN physical layer standards listed by NXP. Its standby function is intended for systems that need low-current operation while retaining bus wake-up capability. The physical two-wire interface supports integration into automotive and industrial CAN networks while leaving arbitration, framing, error management, and message scheduling to the CAN controller. Technical use requires a CAN controller with TXD and RXD signal connections, a suitable transceiver supply, CAN bus termination, common-mode support, and correctly configured logic levels. The standby pin and mode timing should be reviewed against the system power-management strategy because entering or leaving standby can affect node availability. Because the verified excerpt does not provide a complete timing table, absolute transceiver delay, loop-delay, propagation-delay, receiver threshold, bus-fault, and current-limit values are left as data-needed fields rather than inferred. Typical applications include automotive body and powertrain electronics, industrial automation equipment, transport systems, embedded gateways, motor controllers, sensor networks, and CAN-based diagnostic equipment. The 8-pin SOIC package is useful when a through-hole-compatible surface-mount assembly process and a compact two-wire bus interface are required. For robust PCB implementation, place the transceiver close to the connector and CAN bus routing, provide solid ground-plane continuity, route CANH and CANL as a tight differential pair, and place termination only at the physical ends of the bus. Verify that the selected CAN controller, supply voltage, transceiver mode pins, and termination strategy match the complete manufacturer datasheet before production release. This page consolidates verified NXP product information, distributor references, package details, interface standards, application context, and design guidance. Missing electrical timing, current, environmental, and absolute maximum values are explicitly marked where the supplied verified data does not support a trustworthy value.

询价 联系我们
TJA1049TKJ - 5 Mbps CAN Transceiver, 8-HVSON | NXP
TJA1049TKJ

TJA1049TKJ - 5 Mbps CAN Transceiver, 8-HVSON | NXP

The NXP Semiconductors TJA1049TKJ is a 5 Mbps high-speed CAN transceiver with a 4.75 V to 5.25 V supply range, one transmitter, and one receiver in an 8-pin HVSON surface-mount package measuring 3 mm by 3 mm. It interfaces a Controller Area Network protocol controller with a physical two-wire CAN bus and includes standby support for low-power operation. According to the NXP datasheet, the device is designed for automotive high-speed CAN applications. A CAN transceiver is an interface IC that converts logic-level controller signals into differential bus voltages and converts received differential bus levels into logic-compatible receive signals. In the system hierarchy, the TJA1049TKJ belongs to the CAN physical-layer transceiver class, connecting a CAN controller or microcontroller to the CANbus network while providing differential transmit and receive capability. The verified specifications identify a 1/1 driver and receiver arrangement, half duplex operation, 5 Mbps maximum data rate, and 300 mV receiver hysteresis. Its 4.75 V to 5.25 V operating supply range supports regulated 5 V automotive and embedded CAN systems. The standby function can reduce activity when the node is not required to communicate, while the small 8-HVSON package supports compact automotive electronics designs. The TJA1049TKJ is positioned for in-vehicle networks, diagnostic interfaces, body electronics, gateway modules, and industrial or embedded systems using high-speed CAN. It is suitable where a controller requires a physical-layer transceiver rather than a complete CAN controller. System designers must still provide appropriate bus termination, common-mode protection, decoupling, and PCB routing for the installed network topology. The package and pin configuration require careful attention to exposed-pad soldering and thermal behavior. Because the verified source data does not provide a detailed pin-by-pin public pinout, the pinout field is marked unavailable rather than reconstructed from memory. Application selection should also confirm the exact NXP ordering variant, package, and exposed-pad land pattern before PCB release. This page combines the verified manufacturer and distributor references with package-level engineering guidance, comparison fields, and application context for engineers evaluating the TJA1049TKJ. It distinguishes verified specifications from parameters that require confirmation from the complete manufacturer datasheet before layout or qualification decisions.

询价 联系我们
TJA1050 - High-Speed CAN Transceiver, 5V | NXP Semiconductors
TJA1050

TJA1050 - High-Speed CAN Transceiver, 5V | NXP Semiconductors

The NXP TJA1050 is a high-speed Controller Area Network (CAN) transceiver that provides the physical interface between a CAN protocol controller and the physical CAN bus, supporting data rates up to 1 Mbit/s in a standard 8-pin SO (SOIC-8) package. Designed for 5V supply operation, the TJA1050 delivers excellent electromagnetic compatibility (EMC) performance and very low power consumption, making it well-suited for both industrial and automotive applications. A CAN transceiver is an interface IC that sits between a microcontroller's CAN protocol controller and the differential CANH/CANL bus wires. Its hierarchical role is: CAN transceiver → bus interface IC → interface integrated circuit → semiconductor. The TJA1050 family forms part of NXP's third-generation high-speed CAN transceivers, succeeding earlier devices like the PCA82C250 with improved slope control, lower electromagnetic emissions, and integrated protection features against bus shorts and transient voltages. Key features include an operating supply voltage range of 4.75V to 5.25V, low quiescent current consumption, integrated thermal protection, and a recessive bus output voltage that approximates the supply voltage (VCC) for improved logic-level compatibility. The device supports both normal and silent (standby-like) modes selected via the S pin and provides differential transmit/receive capability across an extended common-mode range on the bus. Differential receiver thresholds are tightly controlled to support CAN-FD-ready bit timing in many classic CAN networks. The architecture uses a current-driven recessive output and a dominant-driving topology with slope control to minimize ringing and RF emissions. An internal watchdog and thermal shutdown safeguard the die against bus shorts to battery or ground, while an undervoltage detection circuit disables the transmitter when VCC drops below the operational threshold to prevent erroneous bus states during power-up or power-down sequences. Typical applications include automotive body control modules, industrial CAN-based sensor networks, building automation gateways, and battery management systems where galvanic isolation can be implemented with a transformer or capacitive barrier after the transceiver stage. The TJA1050 is commonly paired with 8-bit or 32-bit microcontrollers that include an integrated CAN controller, such as NXP's LPC and S32K families. When designing with the TJA1050, place a 120 Ω termination resistor at each end of the CAN bus segment and keep the stub length under roughly 30 cm at 1 Mbit/s. Decouple VCC with a 100 nF ceramic capacitor close to the supply pin, and provide adequate ground plane coverage under the bus traces to maintain the differential impedance target of 120 Ω. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
TJA1050T/CM - 1Mbit/s CAN Transceiver | NXP | SOIC-8
TJA1050T/CM

TJA1050T/CM - 1Mbit/s CAN Transceiver | NXP | SOIC-8

The NXP Semiconductors TJA1050T/CM is a 1/1 high-speed CAN transceiver with a 4.75 V to 5.25 V supply range, data rates up to 1 Mbit/s, and an 8-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and a two-wire differential CAN bus. The device supports differential transmission and reception for automotive and industrial networks. A CAN transceiver is an interface IC that converts logic-level controller signals into differential bus signals and converts received bus levels back into digital receive data. In system terms, the TJA1050T/CM belongs to the CAN physical-layer transceiver class, interface IC category, and broader semiconductor hierarchy. Its differential signaling supports noise-resistant communication over long cables and through electrically noisy environments. The verified device data identifies ISO 11898 compatibility, operation up to 1 Mbaud, low electromagnetic emission, a differential receiver with a wide common-mode range, and high electromagnetic immunity. An unpowered node does not disturb the bus lines, while bus-pin protection helps improve robustness. The TXD dominant timeout prevents a permanently dominant transmitter state if TXD is held low by a controller or system failure. The TJA1050T/CM is suitable for CAN-based automotive electronics, industrial control systems, embedded equipment, and communications infrastructure. The NXP product page describes its use between a CAN protocol controller and a two-wire CAN bus. Its 5 V supply requirement makes controller-interface compatibility especially relevant for legacy systems designed around 5 V logic. PCB implementation requires careful termination and bus routing. CAN-H and CAN-L should be treated as a differential pair, with a 120 ohm termination installed at each end of the main bus. The supply should be decoupled close to the device, and the transceiver should be positioned to minimize exposed high-current bus traces. The product page marks the TJA1050 as end of life, so engineers should treat availability and lifecycle migration as important design constraints. The TJA1050T/CM is therefore most appropriate for maintaining or repairing existing 5 V CAN designs, while new designs should confirm the NXP migration path and validate pin, electrical, and protocol compatibility before release. This page combines manufacturer lifecycle information, distributor product identifiers, verified CAN features, and practical interface guidance for engineers evaluating TJA1050T/CM procurement, replacement, PCB reuse, and legacy-system support.

询价 联系我们
TJA1051T/1J - 5 Mbit/s High-Speed CAN Transceiver | NXP
TJA1051T/1J

TJA1051T/1J - 5 Mbit/s High-Speed CAN Transceiver | NXP

The NXP TJA1051T/1J is a 5 Mbit/s high-speed CAN transceiver with 5 V operation, differential transmit and receive capability, and an 8-pin SOIC package. It interfaces a CAN protocol controller to a physical two-wire CAN bus and is associated with automotive applications. The device is also described as normal-mode, SILENT-mode-capable and AEC-Q100 qualified in the supplied component data. A CAN transceiver is the physical-layer interface between a microcontroller or dedicated CAN controller and the CAN bus. The controller generates and interprets logic-level CAN TX and RX signals, while the transceiver converts those signals into the differential CANH and CANL bus signals. A high-speed CAN physical layer supports differential signaling, noise rejection and reliable communication over twisted-pair wiring. The TJA1051T family is positioned for high-speed CAN networks at data rates up to 5 Mbit/s. The verified component listing identifies a nominal 5 V supply, normal/silent operation, 8-pin SO packaging and tape-and-reel ordering for TJA1051T/1J. NXP also states that TJA1051T is backward compatible with the TJA1050, which is important when upgrading an existing CAN interface. The TJA1051 provides separate transmit-dominant, silent and receive behavior for bus management. Silent mode can be useful when a node must monitor or receive without driving the bus, although network software must coordinate this state with other nodes to avoid hidden transmitter conflicts. The device should be paired with an appropriate CAN controller, bus termination, common-mode protection and a correctly decoupled 5 V supply. Typical installations include automotive body, powertrain-adjacent, gateway and diagnostic networks; industrial automation equipment; elevator and building-control systems; and embedded CAN gateways. The 5 Mbit/s capability suits short, well-terminated, high-quality CAN networks where maximum latency is more important than long cable distance. In every case, PCB layout, grounding and bus protection remain critical. For layout, place the transceiver close to the bus connector, provide a continuous ground reference, route CANH and CANL as a coupled pair, and place termination only at the physical ends of the bus. Avoid long stubs between the transceiver and connector. Power filtering and common-mode chokes may be needed when the cable leaves the controlled PCB environment. This page combines the verified NXP and distributor information with practical selection, layout and sourcing guidance. It also distinguishes verified facts from parameters that require confirmation from the complete manufacturer datasheet or current distributor inventory before design release.

询价 联系我们
TJA1051T/2Z - 5 Mbit/s Silent-Mode CAN Transceiver | NXP
TJA1051T/2Z

TJA1051T/2Z - 5 Mbit/s Silent-Mode CAN Transceiver | NXP

NXP Semiconductors TJA1051T/2Z is a 5 Mbit/s high-speed CAN transceiver with Silent Mode, packaged in an 8-pin SOIC for interface bridging between a CAN protocol controller and a physical two-wire CAN bus. The verified distributor listing identifies the /2 ordering option as a Silent-Mode variant, while the manufacturer document covers the TJA1051T family and its compatibility with TJA1050. Its differential transmit and receive arrangement supports automotive and industrial Controller Area Network nodes. A CAN transceiver is the physical-layer interface within a Controller Area Network. It converts controller TXD and error-indicator signals into differential bus output, then converts differential bus levels into RXD data for the protocol controller. This device sits between digital microcontroller I/O and the CAN_H and CAN_L network conductors, combining bus-driver, receiver, and control functions in one IC. The TJA1051T/2Z headline characteristics are a maximum listed data rate of 5 Mbit/s and an 8-pin SOIC package. Silent Mode provides an operating state identified by the verified product listing, but the supplied excerpts do not quantify its input, output, or supply current. The manufacturer also states that the TJA1051T is backward compatible with the TJA1050, which is important when upgrading an existing CAN node without changing its controller-facing interface. The TJA1051 family targets high-speed CAN networks, including automotive systems, where robust differential signaling and transceiver integration simplify node construction. Differential bus operation rejects common-mode noise better than a single-ended interface when the network, termination, grounding, and connector implementation are correctly designed. This makes the part suitable for vehicle body electronics, industrial automation equipment, embedded controllers, and CAN-based sensors. The primary design consideration is preserving compatibility at both the software and physical layers. A replacement must match the SOIC-8 footprint, pin functions, supply expectations, bus timing, and controller logic. Bus termination, common-mode range, loop delay, recessive/dominant behavior, and maximum cable length must be checked against the complete network design rather than inferred solely from the 5 Mbit/s headline rate. For sourcing and engineering context, this page combines the exact verified distributor identity, manufacturer datasheet link, availability claims, family-level compatibility information, and practical design guidance. It separates verified facts from unspecified electrical details so procurement teams can review TJA1051T/2Z without relying on unverified substitutions.

询价 联系我们
TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP
TJA1052IT

TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP

The NXP TJA1052IT is a galvanically isolated high-speed CAN transceiver that provides a robust interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO package and specifically targeted at Electric Vehicle (EV) and Hybrid Electric Vehicle (HEV) applications. An isolated CAN transceiver is a specialized interface IC that combines a high-speed CAN physical layer with on-chip galvanic isolation, typically using integrated coreless transformer or silicon-dioxide (SiO2) dielectric barriers to withstand high common-mode transients in automotive high-voltage environments. Within the broader semiconductor taxonomy, the TJA1052IT sits in the hierarchy isolated CAN transceiver -> CAN transceiver -> CAN interface IC -> automotive interface IC -> power management & signaling semiconductor. Isolation eliminates ground loops between the low-voltage domain (MCU/host) and the high-voltage CAN bus, which is essential when the ECU and chassis sit at different potentials. Key specifications include integrated galvanic isolation rated to withstand high common-mode voltages, support for CAN data rates up to 1 Mbit/s per ISO 11898-2, a wide supply range on the bus side, and very low loop delay suitable for time-triggered CAN (CAN FD-ready) networks. The 16-pin SO package exposes dedicated pins for VCC (logic-side supply), VBUS (bus-side supply), TXD, RXD, CANH, CANL, and the integrated isolation barrier. Architecturally, the TJA1052IT integrates a digital isolator and a CAN transceiver die, with the isolation barrier providing reinforced insulation. This monolithic approach reduces PCB area versus a discrete transceiver + digital isolator solution and improves reliability by eliminating intermediate interconnects. Typical applications include EV/HEV battery management systems, on-board chargers (OBC), DC fast-charging communication links (ISO 15118 PLC not included), traction inverter CAN nodes, and industrial CAN networks requiring reinforced isolation. When designing with the TJA1052IT, place decoupling capacitors close to both VCC and VBUS pins and respect the creepage/clearance rules on the PCB around pins straddling the isolation domain. The device is drop-in compatible with the TI ISO1042 in 16-SO footprint, simplifying second-source strategies. This page synthesizes distributor pricing, drop-in alternatives, and design notes for the TJA1052IT that are not always presented together in the manufacturer datasheet.

询价 联系我们
TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP
TJA1052IT-1Y

TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP

The NXP Semiconductors TJA1052IT-1Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver housed in a 16-pin Small Outline (SO-16) package. It provides an isolated interface between a CAN protocol controller and the physical two-wire differential CAN bus, integrating on-chip galvanic isolation that traditionally required a separate digital isolator plus a CAN transceiver. The part is specifically targeted at Electric Vehicles (EV) and Hybrid Electric Vehicles (HEV), where robust isolation between high-voltage traction domains and low-voltage ECU communication is mandatory. A CAN transceiver is the physical-layer bridge inside an in-vehicle network: it converts the differential logic-level signals from a CAN controller (TXD, RXD) into the bus-side differential voltage on the CANH and CANL lines that meet ISO 11898-2/-5, while protecting the host controller from bus-level transients. The TJA1052i family adds integrated digital isolation (typically using on-chip coreless transformer technology) to that bridge, replacing a two-chip solution (isolator + transceiver) with a single component and simplifying PCB layout while improving common-mode transient immunity (CMTI) in motor-drive environments. Key features include ISO 11898-2/-5 compliant high-speed CAN data rates up to 1 Mbit/s, integrated galvanic isolation rated for 1 kV (digital isolator channel rating per the part classification), tight loop delay for time-triggered CAN (TTCAN) operation, and integrated bus-side protection for harsh automotive electrical environments. The TJA1052i is designed to operate over the full automotive temperature range and supports low-power standby modes for battery-friendly quiescent current draw when the bus is silent. The architecture uses NXP's high-speed CAN transceiver core combined with on-chip galvanic isolation cells, removing the need for external optocouplers or digital isolator ICs while providing the same reinforced isolation barrier between the CAN controller domain and the bus domain. This two-domain split is essential in EV/HEV powertrain ECUs where the bus may sit on a high-voltage referenced plane. Typical applications include EV and HEV battery management system (BMS) CAN nodes, onboard chargers, DC-DC converter telemetry, electric power steering (EPS) communication links, and industrial CAN-isolated gateways that must bridge different ground domains. Designers use the TJA1052IT-1Y where ISO 11898 bus timing must be preserved across an isolation barrier without adding a discrete isolator stage. A key design consideration is that the bus-side and logic-side grounds must remain galvanically separate; do not bypass the isolation by shorting the two ground planes. Also confirm the 1 kV channel rating meets the end-application's reinforced or basic isolation requirement before reuse in higher-voltage systems. This page synthesizes the NXP datasheet, current distributor pricing, and a curated set of drop-in alternatives that share the same SO-16 footprint - content not aggregated on any single manufacturer or distributor page.

询价 联系我们
TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP
TJA1052IT-5Y

TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP

The NXP TJA1052IT-5Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 5 Mbps interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SOIC package with 5 kV RMS isolation. It targets Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and any application requiring reinforced isolation between bus nodes. The integrated digital isolator and CAN transceiver in one package eliminates the need for a discrete isolator plus discrete transceiver, cutting board area roughly in half and simplifying EMC design. A CAN transceiver is a physical-layer (PHY) device that converts differential CAN logic levels from a microcontroller's CAN controller into the dominant/recessive bus signaling required by ISO 11898-2, while providing bus-side fault protection and EMC robustness. The TJA1052IT specifically adds on-chip galvanic isolation - replacing a two-chip solution (isolator + CAN transceiver) with a single device - and is part of the broader hierarchy: CAN transceiver -> interface IC -> integrated circuit. Key features include data rates up to 5 Mbps (CAN FD capable), an isolation voltage of 5000 V RMS for 1 minute per UL 1577, bus fault protection from -27V to +40V, an operating supply range that supports both 1.8V/3.3V/5V MCU sides, and AEC-Q100 qualification for automotive environments. A low-power standby mode with bus wake-up detection is also present, achieved through a dedicated STBY pin and a remote wake-up pattern recognizer compliant with ISO 11898-5. The TJA1052IT uses NXP's integrated capacitive-coupled isolation technology plus a proven CAN PHY, achieving low loop delay under 200 ns - critical for CAN FD frames at the maximum payload phase. Compared with discrete optocoupler + CAN transceiver solutions, the integrated approach reduces propagation delay variation over temperature by a factor of 2-3, improving timing margin in large or noisy automotive networks. Typical applications include EV/HEV battery management system (BMS) bus isolation, OBC (on-board charger) to VCU communication, industrial CAN bus nodes requiring 5 kV isolation (solar inverters, motor drives), EV charging stations with isolated CAN, isolated industrial sensor hubs, and automotive ECU-to-ECU isolation. A key design consideration is the supply topology: the device has two VCC rails - VCC1 (logic/microcontroller side, 2.5V-5.5V) and VCC2 (bus-side, 4.5V-5.5V) - each requiring local decoupling. Designers should follow NXP application note AN11253 for PCB layout, especially maintaining a creepage/clearance margin under the isolation barrier. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including structured comparison with the TI ISO1042DW as identified in NXP community threads.

询价 联系我们
TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT-2Y

TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP

The NXP TJA1052IT/2Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 2.5 kVrms isolated interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO (SOIC-16, 300 mil) package with capacitive (galvanic) isolation integrated on-chip. The device operates from a 3 V to 5.25 V supply on the logic/microcontroller side and supports a CAN data rate of up to 5 Mbps, making it suitable for Classic CAN and CAN FD frame formats. The integrated isolation removes the need for an external digital isolator + isolated DC-DC combination in many designs, reducing BOM count and PCB area. What is an isolated CAN transceiver? A CAN transceiver is the physical-layer bridge between a CAN controller (typically embedded in a microcontroller) and the differential CAN bus lines (CANH/CANL). A galvanically isolated version inserts a high-voltage barrier - here implemented via on-chip capacitive coupling - between the logic domain and the bus domain, breaking ground loops and protecting low-voltage MCU I/O from high-voltage transients common in automotive 12 V/24 V powertrain systems and industrial installations. Key features of the TJA1052IT/2Y include 1/1 unidirectional channel count, 2.5 kVrms isolation voltage rating, 5 Mbps maximum data rate, a standby mode for low quiescent current, and compatibility with 1.8 V and 3.3 V controller logic via separate VIO/VCC rails. The device is specifically targeted at Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and other automotive applications where high-speed CAN communication must coexist with high-voltage battery and inverter systems. Typical applications include EV/HEV battery management system (BMS) communication gateways, on-board chargers (OBC), traction inverter CAN interfaces, industrial CAN bus nodes requiring reinforced insulation, and isolated debug or service interfaces for automotive ECUs. When designing with the TJA1052IT/2Y, engineers should provide local decoupling on both the logic-side and bus-side supplies, observe creepage/clearance for the 2.5 kV isolation barrier, and verify the standby-mode behavior against the system power-state diagram. This page synthesizes distributor pricing, drop-in alternatives, and practical isolation-layout design notes not consolidated in the standalone manufacturer datasheet.

询价 联系我们
TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver
TJA1055T/1J

TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver

NXP Semiconductors TJA1055T/1J is an enhanced fault-tolerant Controller Area Network transceiver for low-speed data links up to 125 kBd. It operates from a 4.75 V to 5.25 V supply and is packaged in a 14-pin SOIC for surface-mount assembly. The device connects a CAN protocol controller to the physical CANH and CANL bus conductors while providing differential transmit, receive, and fault-tolerance functions. A CAN transceiver is the physical-layer interface between a digital CAN controller and the wired CAN network. The TJA1055 family belongs to the interface-IC hierarchy and is specifically optimized for in-car low-speed communication, where its 125 kBd target complements higher-speed CAN controller and transceiver families. Its enhanced fault tolerance helps maintain operation when the bus is shorted to ground, shorted to the supply, or open-circuit, subject to the detailed protection and operating conditions stated by NXP. Key verified characteristics include a 125 kBd low-speed CAN application target, a 4.75 V minimum supply, a 5.25 V maximum supply, and a 14-pin SOIC package. NXP identifies the TJA1055 as pin-to-pin compatible with the TJA1054 and TJA1054A. Distributor listings also identify TJA1055T/1J as an automotive CAN interface available in tape-and-reel ordering. The transceiver should be placed near the CAN bus connector, with its CANH and CANL pins connected to the protected bus wiring and its TXD and RXD pins connected to the CAN controller. Because the device is intended for passenger-car and other low-speed CAN links, system designers should verify timing, termination, bus topology, logic levels, and protection requirements against the manufacturer datasheet before production release. The TJA1055T/1J is suitable for automotive body electronics, comfort modules, diagnostic equipment, sensor nodes, and other 125 kBd CAN applications. Its principal design consideration is that CAN bus behavior depends on termination, wiring, common-mode conditions, and transceiver protection. A CAN bus should not be treated as a generic communication line; the selected transceiver, controller, and network implementation must be validated together. This page combines verified manufacturer and distributor information, package and ordering details, and application guidance for engineers evaluating a SOIC-14 CAN physical-layer interface.

询价 联系我们
TJA1057BTK - High-Speed CAN Transceiver | NXP Semiconductors
TJA1057BTK

TJA1057BTK - High-Speed CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1057BTK is a high-speed Controller Area Network (CAN) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus in an 8-pin HVSON (3x3 mm) package with exposed pad. It supports data rates up to 5 Mbps (CAN FD capable), operates over a wide supply range of 4.75 V to 5.25 V, and is designed for high-speed CAN applications in the automotive industry. A CAN transceiver (also called a CAN bus driver/receiver) is a physical-layer IC that converts the differential digital signaling of a CAN protocol controller into the differential voltage levels required by the ISO 11898-2 CAN bus standard. It sits between a microcontroller's CAN module and the bus wires (CANH/CANL), providing immunity to common-mode noise and ESD protection. CAN transceivers belong to the broader family of interface ICs and are essential building blocks for in-vehicle networking, industrial automation, and any distributed control system that uses the CAN protocol. The TJA1057BTK delivers differential transmit capability to the bus with controlled slew rate, and differential receive capability with high common-mode rejection. It supports both Normal and Silent operating modes, where Silent mode disables the transmitter for listen-only diagnostics. The device is optimized for low electromagnetic emission (EME) and high electromagnetic immunity (EMI), meeting the stringent automotive requirements for CAN bus communication. Integrated thermal protection, bus dominant time-out, and under-voltage detection on VCC enhance system reliability. The 8-pin HVSON package (3x3 mm) with exposed thermal pad offers a very compact footprint suitable for space-constrained ECUs (Electronic Control Units). The exposed pad provides a low thermal resistance path to the PCB copper, allowing the IC to handle the bus fault conditions specified in ISO 11898-5 without derating. The TJA1057BTK is functionally identical to the TJA1057CT within the SOI3+ process family - they differ only in the VIO supply pin logic level handling. Typical applications include automotive body and comfort ECUs, infotainment CAN interfaces, industrial CAN nodes, building automation, and any embedded system requiring a robust, standardized CAN physical layer. In these use cases, the TJA1057BTK acts as the bus interface between a 3.3 V or 5 V microcontroller's CAN controller and the 12 V automotive CAN bus. A key design consideration is the bus termination: a 120 Ω resistor (or split 60 Ω + 60 Ω with capacitor) must be present at each end of the CAN bus segment. The HVSON exposed pad must be soldered to a copper pad of at least 1 mm² to ensure proper thermal performance under continuous bus fault conditions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The information gain comes from a structured cross-reference analysis combining the TJA1057 datasheet family, the obsolescence brief on TJA1050 replacements, and verified distributor stock data as of 2026-10-16.

询价 联系我们
TJA1057BTK-0J - 5Mbps CAN FD Transceiver, HVSON-8 | NXP
TJA1057BTK-0J

TJA1057BTK-0J - 5Mbps CAN FD Transceiver, HVSON-8 | NXP

The NXP TJA1057BTK-0J is a high-speed CAN (Controller Area Network) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus. Housed in an 8-pin HVSON (3x3 mm) package with exposed pad, it supports data rates up to 5 Mbps and is qualified to AEC-Q100 Grade 1 for automotive applications. A CAN transceiver (also called a CAN bus transceiver or CAN interface IC) is a physical-layer device that converts the digital transmit/receive logic signals of a CAN protocol controller inside a microcontroller into the differential CANH/CANL bus signals required on the actual network. CAN belongs to the broader category of serial communication interface ICs, alongside RS-485, RS-232 and LIN transceivers. The TJA1057 family specifically targets high-speed classical CAN and CAN FD (Flexible Data-rate) networks used for powertrain, chassis and body electronics. Key features include a low electromagnetic emission (EME) common-mode choke design, high electromagnetic immunity (EMS), a low-power Standby mode with remote wake-up capability, and ±8 kV HBM ESD protection on the bus pins (per IEC 61000-4-2 on the bus pins, per datasheet). The transceiver operates from a 4.5 V to 5.5 V VCC supply, supports bus voltages from -27 V to +40 V, and provides a TxD dominant time-out for fail-safe behavior. The TJA1057BTK/0J variant carries the 'B' suffix (VIO supply pin present, allowing direct level-shifting to MCUs at 3.3 V or 5 V) and the 'TK' suffix indicating the 8-pin HVSON package with exposed pad. The /0J suffix designates the production ordering code (tape-and-reel packaging). Internally, the device uses a silicon-on-insulator (SOI) process (NXP SOI3+ family), which gives it excellent ESD and latch-up immunity versus older bulk-silicon CAN transceivers like the TJA1050. Typical applications include automotive body control modules (BCMs), gateway ECUs, instrument clusters, HVAC control units, transmission ECUs and industrial CAN nodes operating up to 1 Mbit/s in classical CAN or 5 Mbps in CAN FD networks. The transceiver interfaces directly to NXP S32K and most third-party automotive MCUs. When designing with this part, place the VCC decoupling capacitor (typically 100 nF) directly adjacent to pin 8 and connect the exposed pad (pin 0) to a large PCB ground plane for thermal dissipation and low-impedance return paths. Match the CANH/CANL bus termination to 120 Ω at the network ends to satisfy ISO 11898-2 and avoid signal-integrity issues at high bus loads.

询价 联系我们
TJA1057GT/1Z - High-Speed CAN Transceiver SOIC-8 | NXP
TJA1057GT/1Z

TJA1057GT/1Z - High-Speed CAN Transceiver SOIC-8 | NXP

The NXP TJA1057GT/1Z is a high-speed CAN (Controller Area Network) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus, housed in an 8-pin SOIC (SO-8) package. Key specifications include ISO 11898-2:2016 conformance, data rates up to 1 Mbit/s on the TJA1057T variant with CAN FD support on other variants, and automotive-grade temperature operation. What is a CAN transceiver? A CAN transceiver is a physical-layer interface IC that converts digital transmit/receive logic signals from a microcontroller CAN controller into differential voltage signals on a two-wire CAN bus (CANH and CANL). It belongs to the hierarchy: CAN transceiver -> CAN interface IC -> Interface ICs -> Integrated Circuits. The transceiver also provides bus protection, fault tolerance (dominant/recessive clamping, TXD dominant time-out), and EMC/ESD robustness required in automotive environments. Key features of the TJA1057 include very low current consumption in standby and go-to-sleep modes with remote wake-up capability, an integrated VIO supply pin on /3 variants for direct interfacing with 3.3V and 5V microcontrollers, and an undervoltage detection on VCC and VIO supplies. The TJA1057 implements the CAN physical layer per ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5, with the TJA1057T explicitly specified for data rates up to 1 Mbit/s. Architecturally, the device uses a differential transmit/receive path with slope control for low-EMI operation, an internal LDO for digital supply, and a sophisticated thermal protection scheme. Its split-pin output stage balances common-mode stability with low electromagnetic emissions, making it well-suited for automotive body, chassis, and powertrain networks. Typical applications include automotive body control modules, gateway ECUs, infotainment CAN nodes, industrial CAN automation nodes, and CAN-FD enabled instrument clusters. Its robustness against ESD (>6 kV HBM) and bus fault voltages (±58 V) makes it dependable in harsh electrical environments. When designing with this device, ensure proper bus termination with 120 ohm resistors at each end of the bus and a common-mode choke for EMI-sensitive applications. The TJA1057 requires careful placement of the VCC decoupling capacitor close to pin 1 to maintain supply stability during dominant-to-recessive transitions. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
TJA1057GTJ - High-Speed CAN Transceiver, 1Mbps, 8-SO | NXP
TJA1057GTJ

TJA1057GTJ - High-Speed CAN Transceiver, 1Mbps, 8-SO | NXP

The NXP Semiconductors TJA1057GTJ is a high-speed Controller Area Network (CAN) transceiver in the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus, delivered in an 8-pin SO (SOIC-8) surface-mount package. It supports data rates up to 1 Mbit/s, operates from a 4.75 V to 5.25 V supply, and is qualified for the -40 °C to +150 °C automotive temperature range. The TJA1057GTJ integrates differential transmit/receive capability, standby mode, and superior EMC and ESD performance versus earlier-generation transceivers. A CAN transceiver is the physical-layer (PHY) bridge between a digital CAN protocol controller (typically integrated into a microcontroller) and the differential CAN bus wiring in a vehicle or industrial network. Transceivers convert the controller's TX/RX logic-level signals into the ISO 11898-2 compliant differential bus levels, and they protect the controller from bus-level transients. The TJA1057GTJ belongs to NXP's Mantis family, which improved on the predecessor TJA1051/TJA1042 series by offering lower electromagnetic emissions and higher ESD robustness while maintaining pin compatibility. Key specifications include: 1 Mbit/s maximum data rate, 4.75 V to 5.25 V supply range, low-current standby mode, ISO 11898-2 conformance, bus pin ESD robustness of ±8 kV HBM (typical), and integrated thermal protection. The device is optimized for 12 V automotive systems and supports both normal and standby operation modes. The SOIC-8 package offers a standard 3.9 mm body width suitable for reflow soldering in automotive PCB assemblies. Architecturally, the TJA1057 uses a silicon-on-insulator process node that allows the bus pins (CANH, CANL) to survive load-dump transients up to ±42 V typical without external protection, while maintaining low quiescent current in standby mode. The device includes slope control for reduced EMI, dominant-timeout protection, and a bus-dominant detection feature that prevents the controller from being locked in a dominant state if a wiring fault occurs. Typical applications include automotive body and powertrain CAN nodes, industrial CANopen networks, gateway ECUs, and any 5 V microcontroller-based system requiring an ISO 11898-2 compliant physical layer. It is widely used in BMS modules, HVAC controllers, instrument clusters, and ADAS sensor nodes where reliable high-speed differential communication is required. When designing with the TJA1057GTJ, place a 100 nF decoupling capacitor close to pin 8 (VCC) and respect the bus termination scheme (typically 120 Ω at each end of the CAN bus segment). The standby pin (STB) should be tied to GND through a pull-down or controlled by the host MCU; a high level puts the part into low-power standby with the bus monitor still functional. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-references to TJA1057 family members and other 8-pin high-speed CAN transceivers.

询价 联系我们
TJA1057GTK - High-Speed CAN Transceiver, 1 Mbit/s, 8-HVSON | NXP
TJA1057GTK

TJA1057GTK - High-Speed CAN Transceiver, 1 Mbit/s, 8-HVSON | NXP

The NXP TJA1057GTK is a high-speed Controller Area Network (CAN) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus in a compact 8-pin HVSON (3x3 mm) package with an exposed thermal pad. It supports data rates up to 1 Mbit/s, operates from a 4.75V to 5.25V supply, and delivers differential transmit/receive capability required by automotive in-vehicle networks. The TJA1057GTK variant includes a standby mode for low-power operation and is optimized for superior electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance. A CAN transceiver is a physical-layer interface IC that converts the digital transmit (TXD) and receive (RXD) signals from a CAN controller into the differential CANH and CANL bus voltages defined by the ISO 11898-2 standard. Within the broader hierarchy, a CAN transceiver sits below the CAN controller (typically inside a microcontroller) in the Open Systems Interconnection (OSI) model and sits above the physical bus medium. Without a transceiver, a controller cannot meet the bus-level timing, drive strength, or fault protection that an automotive CAN bus demands. Key features include a low-current standby mode with remote wake-up via bus activity, thermal protection, bus-dominant time-out to prevent a stuck node from blocking the bus, and an undervoltage detection on the VCC supply. The HVSON-8 package features an exposed thermal pad that reduces junction-to-ambient thermal resistance, enabling AEC-Q100-qualified automotive operation across the -40C to +125C range. The TJA1057 is pin-compatible with the legacy TJA1050 footprint in SO-8 but uses the smaller, thermally enhanced HVSON-8 package in this GTK suffix variant. The transceiver uses a symmetric differential driver stage that minimizes electromagnetic emissions, and the receiver incorporates a wide common-mode range to tolerate ground shifts between nodes on long bus runs. An integrated slope-control resistor optimizes the rise/fall times of the CANH/CANL edges to balance emissions against bit-timing symmetry. Typical applications include automotive body control modules, gateway ECUs, infotainment CAN interfaces, industrial CANopen networks, and any 12V/24V automotive subsystem that communicates via CAN at speeds from 10 kbit/s to 1 Mbit/s. Designers select the TJA1057GTK when EMC performance and a small PCB footprint outweigh the need for the higher bus-fault voltage ratings of the TJA1055 or TJA1044. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VCC pin, keep the CANH/CANL traces short and symmetric with characteristic impedance near 120 ohm, and verify that the termination resistance at each end of the bus totals 120 ohm to prevent signal reflections. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical EMC/layout notes drawn from the NXP TJA1057 datasheet family, offering context the manufacturer product page alone does not provide.

询价 联系我们
TJA1057T/1Z - High-Speed CAN Transceiver | NXP SOIC-8
TJA1057T/1Z

TJA1057T/1Z - High-Speed CAN Transceiver | NXP SOIC-8

The NXP TJA1057T/1Z is a high-speed Controller Area Network (CAN) transceiver in the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus. Housed in an 8-pin SO (SOIC-8) package and specified for data rates up to 1 Mbit/s, it implements the CAN physical layer defined in ISO 11898-2:2024 third edition and SAE J2284-1 to SAE J2284-5, with additional timing parameters enabling reliable CAN FD fast-phase communication up to 5 Mbit/s. A CAN transceiver, also called a CAN physical-layer (PHY) chip, sits between a microcontroller's CAN protocol controller and the differential CANH/CANL bus wires. It transmits and receives differential signals, controls the slope of the dominant-to-recessive transitions, and provides ESD protection and bus-fault tolerance. The TJA1057 belongs to the Mantis CAN transceiver lineage that supersedes the older TJA1050; its position in the hierarchy is: CAN transceiver -> CAN interface IC -> automotive communication IC -> semiconductor. Key features include very low-current standby mode with remote wake-up via bus activity recognition, high ESD robustness on the bus pins (typical >8 kV HBM), excellent electromagnetic compatibility (EMC) performance under both dominant and recessive states, and an integrated VIO supply pin (on related variants) allowing direct connection to 3.3 V microcontrollers. It supports an extended supply voltage range, an operating junction temperature range suitable for automotive under-hood environments, and a low-power sleep current that simplifies ECUs designed for quiescent-current budgets. The device translates a single-ended TXD logic input from the CAN controller into a differential CANH/CANL output, and converts the bus differential back to a single-ended RXD logic output. It offers an SPLIT output pin (on related variants) for stabilizing the recessive bus level in networks with many nodes. The TJA1057 is a successor to the TJA1050 and is pin-compatible with several Mantis-family derivatives, simplifying PCB reuse across OEM programs. Typical applications include automotive body control modules, CAN gateways and powertrain nodes, electric vehicle battery management system communication, industrial CAN-bus automation (CANopen, DeviceNet), and any application needing an ISO 11898-2 compliant differential CAN link to a microcontroller. The 1 Mbit/s nominal / 5 Mbit/s CAN FD fast-phase capability suits both classical CAN and modern CAN FD networks. When designing with this IC, place the bus-side ESD/TVS protection and common-mode choke as close to the CANH/CANL pins as possible, and provide a solid ground pour under the SOIC-8 body. Decouple VCC with at least 100 nF and 4.7 µF local capacitance. Match the bus termination: 120 Ω between CANH and CANL at each end of the bus, plus optional split termination (60 Ω + 60 Ω to ground) for improved EMC. This page synthesizes distributor pricing, NXP Mantis-family drop-in alternatives, and practical design notes not found in the standalone TJA1057 datasheet.

询价 联系我们
TJA1059TK - Dual HS-CAN Transceiver with Standby Mode | NXP
TJA1059TK

TJA1059TK - Dual HS-CAN Transceiver with Standby Mode | NXP

The NXP TJA1059TK is a dual high-speed CAN (HS-CAN) transceiver with integrated standby mode, housed in a 14-pin HVSON (3x4.5 mm) package. It provides the physical interface between a CAN protocol controller (typically a microcontroller) and the physical two-wire CAN bus, supporting differential transmit and receive signaling at data rates up to 1 Mbit/s as defined by ISO 11898-2:2024. A CAN transceiver is the physical-layer analog front-end of a Controller Area Network, the dominant in-vehicle serial bus. It level-translates digital TXD/RXD signals from a microcontroller (typically 3.3V or 5V CMOS logic) to the differential CANH/CANL bus signals that traverse the vehicle harness, while also providing bus protection, dominant bit clamping, and high-impedance bus isolation when unpowered. Key features of the TJA1059TK include two independent HS-CAN transceiver channels in a single package, a low-power standby mode activated through the STB pin, very low quiescent current in standby (suitable for battery-supplied ECUs during key-off), built-in dominant and recessive bit clamping, bus-pin protection against ±8 kV ESD (HBM) and ±6 kV IEC 61000-4-2, and a wide operating voltage range from 4.75 V to 5.25 V. Each channel is also designed to survive 12V load-dump and reverse-battery transients typical of automotive 12V nets. Architecturally, the TJA1059TK integrates two complete ISO 11898-2 transceivers with separate TXD/RXD lines from the host MCU, sharing the supply pins for both channels. The standby mode disables the entire receiver function for power savings while keeping a low-power bus monitor (variants differ). It is fabricated on a robust BiCMOS process optimized for 5V analog operation with high immunity to automotive EMI. Typical applications include automotive body control modules (BCMs), gateway ECUs between CAN segments, powertrain domain controllers, ADAS sensor fusion modules with dual CAN channels, CAN-based industrial sensor networks, and truck/bus chassis control units. The dual-channel integration saves PCB area in space-constrained ECUs and reduces BOM cost versus two discrete single-channel transceivers. When designing with this device, route the CANH/CANL traces as a 120-ohm-impedance differential pair with symmetric length matching. Place a 100nF decoupling capacitor close to VCC, and avoid ground loops by using a single-point low-impedance ground stitch near the transceiver. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on generic search engines - including same-package HVSON options and recommended companion MCUs for dual-channel CAN ECUs.

询价 联系我们
TJA1059TKJ - Dual 1Mbps CAN Transceiver | NXP
TJA1059TKJ

TJA1059TKJ - Dual 1Mbps CAN Transceiver | NXP

The NXP Semiconductors TJA1059TKJ is a dual high-speed CAN transceiver with a maximum data rate of 1 Mbps, two independent CAN channels, differential transmit and receive, and a 14-pin HVSON package measuring 3 mm by 4.5 mm. It is designed to interface a CAN protocol controller in a microcontroller with a physical two-wire CAN bus. A CAN transceiver is an interface IC between the digital CAN protocol controller and the physical differential bus. It converts controller logic into high-speed differential CAN signals and converts received bus levels into digital receive data. The TJA1059 therefore belongs to the hierarchy CAN transceiver → network interface IC → integrated circuit, and is intended for automotive and truck electronics. Key features include two CAN channels, high-speed operation up to 1 Mbps, standby mode, differential signaling, and a 5 V automotive supply context. The dual-channel architecture allows one controller or network node to serve two independent CAN buses or to expose two physical interfaces. Its surface-mount HVSON construction supports compact automotive electronics while its exposed pad assists thermal performance when the package layout is designed correctly. Technically, the transceiver separates the CAN transmit, receive, and standby functions within a robust physical-layer interface. Differential bus signaling improves noise immunity in vehicle environments, while standby mode can reduce activity when the interface is not required. Designers must still validate signal timing, bus termination, grounding, electromagnetic compatibility, and thermal conditions against the complete vehicle or industrial network architecture. Typical applications include automotive body and comfort controllers, truck electronics, CAN gateways, infotainment modules, engine or chassis control units, and industrial vehicle networks. The two channels are useful where a controller needs dual CAN connectivity without using two separate single-channel transceiver packages. A critical design consideration is preserving the exposed-pad thermal and electrical layout recommended by NXP. CAN bus traces should be routed as a controlled differential pair, with termination placed only at the physical ends of the bus. Standby-control polarity and timing must be verified in the system-level state machine. This page consolidates the verified NXP datasheet description, distributor identification, package information, price reference, and application guidance for engineers evaluating the TJA1059TKJ.

询价 联系我们
TJA1083TTJ - 10Mbit/s FlexRay Transceiver | NXP
TJA1083TTJ

TJA1083TTJ - 10Mbit/s FlexRay Transceiver | NXP

The NXP Semiconductors TJA1083TTJ is a FlexRay node transceiver designed for 2.5 Mbit/s to 10 Mbit/s communication systems, with a 4.45 V to 5.25 V supply range and a 14-pin TSSOP package. According to the NXP datasheet, it complies with the FlexRay Electrical Physical Layer specification V3.0.1 and implements the JASPAR Increased voltage amplitude transmitter functional class. It combines one transmitter and one receiver for interface duty in distributed in-vehicle communication networks. A FlexRay node transceiver is a physical-layer interface IC that connects a controller or network node to a two-wire FlexRay bus. FlexRay uses deterministic, high-speed communication suited to automotive systems where predictable scheduling, fault tolerance, and simultaneous signal propagation matter. In the broader hierarchy, this device is an automotive network interface transceiver, an interface IC, and a semiconductor rather than a general-purpose protocol controller. The verified feature set includes one transmit driver and one receive driver, operation from 2.5 Mbit/s to 10 Mbit/s, a 4.45 V minimum and 5.25 V maximum supply, and a 14-TSSOP surface-mount package. Distributor information identifies the TTJ ordering code as reel packaged. Automotive qualification is listed by Arrow, while detailed AEC-Q100 qualification status and grade are not supplied in the verified excerpts. Typical uses include automotive FlexRay controller interfaces, body and chassis control modules, gate controllers, sensor nodes, power-distribution controllers, and other ECUs connected to a FlexRay backbone. The device handles the physical bus termination, signal transmission, reception, and common-mode interface functions described in the manufacturer documentation, while protocol and arbitration remain the responsibility of the associated FlexRay controller. Designers should verify the complete pin configuration, electrical limits, termination requirements, exposed thermal needs, and system-level bus topology against the manufacturer datasheet before layout release. The TSSOP package is compact, but its lead pitch and automotive operating requirements demand careful PCB escape routing, clean return paths, and controlled supply bypassing. Distributor listings also show a typical factory lead time of approximately 70 days, so procurement planning should include that stated interval. This page consolidates the verified manufacturer description, distributor availability details, package information, and engineering guidance for engineers evaluating a 10 Mbit/s FlexRay physical-layer transceiver. It does not infer unreleased specifications or substitute similarly named interface devices without verified pin compatibility.

询价 联系我们
TJA1086HNJ - FlexRay Active Star Coupler | NXP
TJA1086HNJ

TJA1086HNJ - FlexRay Active Star Coupler | NXP

The NXP Semiconductors TJA1086HNJ is a FlexRay active star coupler with one transmit and one receive channel, a 10 Mbps data rate, and a 44-pin HVQFN 9x9 mm package. It connects two FlexRay network branches and integrates branch expansion through its TRXD0 and TRXD1 interfaces. According to the available TJA1086 documentation, the device complies with the FlexRay electrical physical layer specification V3.0.1. A FlexRay active star coupler is an interface and network-topology component that distributes a communication-controller signal between two physical branches while providing the required network termination and electrical behavior. In the broader hierarchy, it belongs to automotive network interfaces, transceivers, and physical-layer devices. It is used where an electronic control unit needs deterministic communication with other FlexRay nodes through a star-coupled network. The TJA1086HNJ is identified by distributor listings as a 1TX/1RX FlexRay transceiver-class device rated for 10 Mbps and supplied in a 44-pin HVQFN package with an exposed pad. Its automotive qualification is indicated by the Arrow listing, which identifies the part as AEC-Q100 automotive. The package and exposed-pad construction are important for thermal design and PCB layout, while the two-branch architecture is important when planning network topology. The TJA1086 can be used in automotive ECUs, gateway modules, body controllers, powertrain controllers, and other FlexRay nodes. Its dedicated communication-controller interface allows integration into an ECU, while TRXD0 and TRXD1 permit multiple TJA1085 or TJA1086 devices to increase the number of branches in a network. The supplied search data does not provide complete electrical limits, pin names, package dimensions, or absolute maximum ratings, so those values must be confirmed in the manufacturer datasheet before design release. For PCB implementation, preserve the manufacturer’s recommended HVQFN land pattern, exposed-pad connection, decoupling, and return-path arrangement. Keep FlexRay traces short and controlled, provide the specified termination and protection networks, and verify signal integrity with the intended communication-controller configuration. Do not infer pin compatibility from a similar package name; verify every pin, supply requirement, and timing parameter against the TJA1086 datasheet. This page consolidates verified distributor identification, FlexRay functionality, package information, sourcing links, and engineering-selection guidance. It distinguishes verified facts from parameters that require datasheet confirmation, helping engineers identify whether the TJA1086HNJ fits an automotive FlexRay star-coupler design before requesting detailed technical documents.

询价 联系我们
TJA1100HN - 100BASE-T1 Automotive Ethernet PHY | NXP | QFN-36
TJA1100HN

TJA1100HN - 100BASE-T1 Automotive Ethernet PHY | NXP | QFN-36

The NXP Semiconductors TJA1100HN is an IEEE 100BASE-T1 compliant single-port Automotive Ethernet PHY transceiver housed in a 36-pin HVQFN (QFN-36) package with exposed thermal pad. It supports 100 Mbit/s transmit and receive capability over a single unshielded twisted pair (UTP) cable for at least 15 m, optimized for automotive Ethernet backbones and sensor links in advanced driver assistance systems (ADAS). An automotive Ethernet PHY (Physical Layer transceiver) is the analog/digital mixed-signal device that sits between an Ethernet MAC (Media Access Controller) and the physical twisted-pair cable, performing line coding (PAM-3 for 100BASE-T1), clock recovery, echo cancellation, and signal equalization. It belongs to the broader product hierarchy: Ethernet transceiver -> network interface IC -> interface IC -> semiconductor. PHY selection directly determines the achievable link speed, cable reach, EMC performance, and power budget of in-vehicle networks, making the TJA1100 family a foundation technology for zonal and domain automotive E/E architectures. Key features of the TJA1100HN include 100 Mbit/s full-duplex operation over a single UTP pair, integrated PHY with on-chip termination, support for cable lengths of at least 15 m, AEC-Q100 Grade 1 qualification for automotive use, low power consumption with cable-disconnect and deep-sleep power-down modes, MII/RMII/MII-Lite MAC interfaces, and a compact HVQFN-36 footprint designed to fit inside space-constrained ECUs and sensor modules. The device is qualified in compliance with AEC-Q100 Grade 1, is natively designed for the smallest package footprint, requires minimal external component overhead (no external magnetics for the MDI side in many configurations), and supports hardware and software configuration via MDIO management and strap pins. Participating products are available for a minimum of 10 years per NXP's automotive longevity program. Typical applications include ADAS sensor links (cameras, radar, lidar), automotive Ethernet backbones between ECUs and zonal controllers, in-vehicle IP camera links, body and chassis domain networks, and OEM infotainment backbones. Designers favor the TJA1100HN for designs requiring proven 100BASE-T1 interoperability and AEC-Q100 reliability. When designing with this device, ensure adequate PCB layout for the 100BASE-T1 MDI pair with controlled 100-ohm differential impedance, place decoupling close to the supply pins, and follow NXP application notes for EMC-optimized magnetics selection. Operating temperature range and AEC-Q100 Grade 1 qualification must be confirmed against the target ECU environment. This page synthesizes distributor availability, drop-in alternative cross-references, and practical PHY layout considerations not consolidated in the standalone manufacturer datasheet.

询价 联系我们
TJA1100HNZ - 100BASE-T1 Automotive Ethernet PHY | NXP
TJA1100HNZ

TJA1100HNZ - 100BASE-T1 Automotive Ethernet PHY | NXP

The NXP Semiconductors TJA1100HNZ is an IEEE 100BASE-T1-compliant single-port Automotive Ethernet PHY transceiver supporting 100 Mbit/s transmit and receive operation over at least 15 m of unshielded twisted pair in a 36-pin HVQFN package. It is designed for automotive Ethernet links in IP cameras, driver-assistance systems, and backbone networks. A 100BASE-T1 PHY is a physical-layer interface IC that converts digital Ethernet data into electrical signals for a single twisted-pair cable and converts received signals back into digital data. It sits between an Ethernet MAC or automotive ECU and the physical cable. The TJA1100HNZ therefore belongs to the automotive network interface hierarchy: Ethernet controller, PHY transceiver, 100BASE-T1 interface, and physical-layer semiconductor. Key verified features include one Ethernet PHY port, 100 Mb/s operation, MII and RMII host interfaces, 3.3 V supply operation, operation from -40°C to +125°C, and AEC-Q100 automotive qualification. The device supports cable lengths of at least 15 m, helping it address compact vehicle wiring environments while reducing cable weight compared with conventional higher-channel-count Ethernet links. The TJA1100HNZ integrates the analog PHY and digital host-side interface needed for a 100 Mbit/s automotive Ethernet connection. Its MII and RMII interfaces provide compatibility with different controller arrangements, although the selected host interface, clocking, and software configuration must be checked against the complete system design. The 3.3 V operating supply is suitable for automotive electronic control units where low-voltage digital rails are common. Typical applications include IP camera links, driver-assistance systems, automotive backbone Ethernet, vehicle infotainment networks, and other in-vehicle Ethernet nodes. The single-pair cable architecture can simplify vehicle wiring compared with multi-pair Ethernet, while the automotive temperature rating and AEC-Q100 qualification support harsh operating environments. When laying out a TJA1100HNZ PCB, preserve the recommended high-speed copper connections and provide clean power and ground planes around the PHY. Differential pair routing, impedance control, return-path continuity, and separation from noisy switching circuits are essential because cable-side signal integrity affects link reliability. The supplied data confirms a 36-pin HVQFN package, but individual pin names and detailed layout values require the NXP datasheet.

询价 联系我们