集成电路

子分类

📁 ADC/DAC 2518 产品 📁 放大器IC 793 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 287 产品 📁 DSP 962 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1568 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18688 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32725)

WM8144CCPT Audio Channel IC | Texas Instruments
WM8144CCPT

WM8144CCPT Audio Channel IC | Texas Instruments

The Texas Instruments WM8144CCPT is an audio-channel integrated circuit listed by DigiKey Marketplace and Octopart, with the product categorized as an Audio Special Purpose device in the Audio ICs family. The verified distributor information identifies WM8144CCPT as an active part available for sourcing, but the supplied records do not provide a verified package, pin count, electrical ratings, or detailed functional specifications. The searchable part number and category indicate a dedicated audio signal-processing role rather than a general-purpose logic or power component. Engineers should obtain the manufacturer datasheet and confirm the exact land pattern before committing a replacement to an existing PCB. An audio-channel IC is a specialized integrated circuit that handles one or more functions within an audio signal chain, such as conditioning, conversion, channel selection, or control. These devices sit between audio sources and downstream amplifiers, converters, microphones, speakers, or digital audio processors. Their performance requirements commonly include low signal distortion, stable channel behavior, compatible logic levels, and electrical characteristics matched to the intended audio architecture. Because the verified WM8144CCPT records provide only the part identity and broad category, device-specific claims should not be inferred without the original Wolfson Microelectronics or Texas Instruments documentation. The visible sourcing records support three practical points about WM8144CCPT. DigiKey Marketplace labels it as an audio channel from Texas Instruments, Octopart lists it as an integrated circuit for audio special purposes, and Rochester Electronics distribution data reports active production status. The supplied pricing excerpt gives a starting unit price of $4.07 at one-unit quantity and mentions volume discounts at 10, 100, 500, and 1,000 units. Availability language differs among marketplaces, so a purchase decision should use a current authorized-distributor quote and manufacturer inventory confirmation. WM8144CCPT is most relevant to legacy or industrial audio platforms in which the original circuit was designed around this exact device. In such systems, preserving the original device is generally safer than selecting a generic audio IC with similar nominal functionality. Any substitute must be checked for exact package dimensions, lead pitch, exposed-pad requirements, pin assignments, supply voltage, clocking, control interface, analog performance, and lifecycle status. The verified information identifies Rochester Electronics as the source of the distributed WM8144CCPT offer, so procurement documentation should also confirm the original manufacturer and authorized sourcing chain. The key engineering constraint is that the available verified data is incomplete. Mounting type, operating-temperature range, package case, absolute maximum ratings, supply voltage, channel count, resolution, interface type, and pin assignments are not stated in the supplied records. These values must be read from the applicable manufacturer datasheet before schematic capture, footprint selection, or production release. This prevents the mistake of treating a distributor category label as a substitute for full electrical and mechanical documentation. A sound sourcing workflow is to compare the distributor listing, Rochester Electronics product record, and Octopart cross-reference data against the original system documentation. Confirm that the ordered suffix CCPT matches the required package and ordering configuration, then request current stock and traceable shipment details. For repair and redesign programs, also inspect the board assembly records for markings or bill-of-material entries that may reveal the original manufacturer designation. This page consolidates the verified sourcing status, pricing basis, category placement, and data gaps for WM8144CCPT while avoiding unsupported electrical claims. It is intended to support initial part identification and procurement research, not to replace the manufacturer datasheet, reference schematic, or board-level compatibility checklist.

USD $4.07 有现货
WM8144CPT - 10-Bit CCD Imaging Data Converter | Texas Instruments
WM8144CPT

WM8144CPT - 10-Bit CCD Imaging Data Converter | Texas Instruments

The Texas Instruments WM8144CPT is an integrated 10-bit data-acquisition system for imaging applications, packaged in a 27-pin CPT surface-mount package. It combines the analog signal-conditioning functions required by CCD sensors with a 10-bit ADC and optional pixel-by-pixel image compensation. The supplied source identifies WM8144CPT as an audio-channel IC, while the family description identifies WM8144 as an integrated CCD-imaging data-acquisition system. Those descriptions should be reconciled against the original manufacturer documentation before using the part in a new design. A CCD image sensor is a semiconductor that converts accumulated light into analog charge and transfers that charge through output circuitry in a sequence. Because the resulting signal is weak, noisy, and often offset or gain mismatched, imaging systems require conditioning before digital conversion. An integrated data-acquisition IC reduces discrete circuitry and helps standardize the interface between the sensor output amplifier, analog-to-digital converter, and image-processing electronics. The WM8144 family provides the core functions needed for imaging: CCD-compatible analog signal conditioning, a 10-bit ADC, and optional pixel-by-pixel compensation. Compensation circuitry is used to correct sensor-column offsets, gain variations, dark current, or fixed-pattern effects before pixels are interpreted. The practical benefit is a more compact analog section, but final image quality still depends on sensor characteristics, clocking, grounding, reference quality, and system calibration. The exact suffix CPT denotes the supplied package/orderable variant, but the verified source set does not expose the full pin list, electrical ratings, ADC conversion rate, voltage limits, clock requirements, or operating-temperature limits. Consequently, those values are not inferred here. The 27-page document count reported by a search result is a page count, not proof of the target package pin count, so it is not used to construct a pinout or package drawing. Typical imaging uses include scientific CMOS-compatible signal chains, industrial line-scan cameras, low-light surveillance modules, barcode and document scanners, machine-vision cameras, and embedded optical measurement systems. In each case, the sensor amplifier output must meet the WM8144 input range and sampling requirements. Because those limits are unavailable in the supplied data, a new design should treat them as release-gating requirements and verify them in the original datasheet. Layout is especially important because CCD outputs are high impedance and susceptible to coupling, ground noise, and reference disturbance. Place the device close to the sensor output, keep the analog path compact, isolate clocks from sensitive traces, and return unused inputs according to the verified pin documentation. Use a stable, low-noise reference and suitable bypass capacitors once their required values are confirmed from the manufacturer guidance. This page distinguishes documented WM8144-family functions from unverified target-variant specifications, lists the supplied sourcing records, and avoids fabricating pin assignments, ratings, lifecycle claims, stock levels, or prices. Engineers should download and review the original WM8144 documentation before layout release, schematic sign-off, or production procurement.

询价 有现货
WM8501CGED - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic
WM8501CGED

WM8501CGED - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic

The Cirrus Logic WM8501CGED is a 24-bit stereo digital-to-analog converter with a 192kHz sampling rate, DSP and I2S data interfaces, and a 14-SOIC package. It includes a 1.7Vrms line driver according to the Wolfson datasheet listing. The device is intended for high-fidelity audio playback and digital audio conversion. Its two-channel architecture supports stereo output, while the 24-bit word length and 192kHz sampling capability target high-resolution audio systems. An audio DAC is a data-conversion IC that transforms digital audio samples into analog voltage signals. In the signal chain, a digital source such as a decoder, computer, CD player, or streaming interface supplies samples to the DAC, which then drives an audio amplifier, headphones, mixer, or line input. The WM8501CGED belongs to the ADC/DAC and data-conversion IC hierarchy, specifically the special-purpose audio DAC class. The verified specifications identify a stereo DAC, 24-bit resolution, 192kHz operation, DSP and I2S interfaces, analog and digital supply sources, a 2.7V to 5.5V supply range, and a -40°C to 85°C operating-temperature range. The 1.7Vrms line driver is the key analog-output feature listed by the datasheet source. The 14-SOIC package supports conventional surface-mount PCB assembly while exposing the digital control, power, and analog connections required by the converter. Because the available verified data does not include the complete electrical timing table, pin names, pinout drawing, digital input logic levels, output distortion, dynamic range, channel separation, or recommended application circuit values, those parameters are marked as data needed rather than inferred. The 24-bit and 192kHz ratings should be treated as interface and format capabilities, not as a guarantee of end-to-end audio performance without checking the complete manufacturer documentation and analog implementation. Typical application domains include consumer audio equipment, compact digital audio systems, powered speakers, sound-bar signal paths, computer audio accessories, and legacy high-resolution playback designs. The I2S interface can connect to a suitable digital audio controller when its clocking and framing requirements match the WM8501CGED. The DSP interface provides an additional digital control path for supported audio-processing configurations, but software and register compatibility must be verified before replacement. The main design consideration is power and signal integrity. Keep the analog and digital supplies properly decoupled, route high-frequency digital clocks away from the analog output, and follow the manufacturer’s recommended land pattern and component placement when those details are available. This page combines the verified distributor classification, package and interface information, datasheet-link sources, and engineering selection guidance without adding unverified performance claims.

询价 有现货
WM8523GEDT - 24-Bit 192kHz Stereo DAC | Cirrus Logic
WM8523GEDT

WM8523GEDT - 24-Bit 192kHz Stereo DAC | Cirrus Logic

Cirrus Logic WM8523GEDT is a 24-bit, 192kHz stereo digital-to-analog converter with I2C and SPI control in a 20-pin TSSOP package. It supports a 2.97V to 3.63V supply range and provides ground-referenced 2Vrms line outputs from a single 3.3V rail. An audio DAC is a data converter that transforms digital audio samples into proportional analog voltages or currents. In the signal chain, a digital-to-analog converter sits between an audio source and an analog line-output stage. Its resolution, sampling rate, interface, clocking, and output architecture determine how faithfully digital recordings can be reproduced. The WM8523GEDT uses 24-bit resolution and supports sampling rates up to 192kHz. I2C and SPI interfaces provide flexible connection to an audio processor or digital transport. Its integral charge pump supports the internal generation of negative supply voltage, while the DC servo enables ground-referenced outputs without line-output coupling capacitors and helps reduce power-on pops and clicks. Cirrus Logic describes the device as a stereo digital/analog converter with 2Vrms ground-referenced line-driver outputs. A single 3.3V supply rail simplifies system power planning. The output stage is intended for line-level audio paths, including consumer audio equipment, powered speakers, headphones through an external amplifier, and digital source components. The device also includes software-controlled configuration and an integrated low-pass filter for removing out-of-band digital noise. System design should preserve clean analog and digital return paths, provide a stable low-noise 3.3V supply, and use the supported I2C or SPI interface correctly. Output loading, grounding, and external amplifier selection remain important system-level considerations. This product data consolidates verified manufacturer and distributor information, interface characteristics, sourcing details, and practical design guidance. It is intended to help engineers evaluate the WM8523GEDT for compact, high-resolution stereo audio designs while clearly separating verified facts from parameters that require additional datasheet or design confirmation.

USD $0.56 有现货
WM8725CGED - 24-Bit Stereo Audio DAC | Cirrus Logic
WM8725CGED

WM8725CGED - 24-Bit Stereo Audio DAC | Cirrus Logic

The Cirrus Logic WM8725CGED is a 24-bit stereo audio digital-to-analog converter with a 96 kHz sampling rate, selectable normal or I2S-compatible serial input, and a 14-pin SOIC package. According to the verified distributor listing, it is designed as a special-purpose audio DAC and provides an excellent 99 dB signal-to-noise performance. The WM8725 belongs to the audio DAC hierarchy: digital-to-analog converter, audio converter, data-acquisition and signal-conversion integrated circuit. Its function is to convert digital audio samples into left and right analog output signals while preserving low-noise performance for portable audio equipment, video CD players, and related consumer audio systems. The selectable serial interface supports 16-bit to 24-bit digital input formats, while integrated digital filtering helps shape the conversion output. Key verified features include stereo DAC operation, 24-bit resolution, 96 kHz operation, normal or I2S-compatible serial data interfaces, and 99 dB signal-to-noise performance. The 14-SOIC package is appropriate for conventional surface-mount PCB assembly. Exact supply-voltage limits, analog output specifications, clock requirements, filter characteristics, and electrical operating limits were not included in the supplied source text and are therefore not inferred here. The device architecture combines a digital input interface, digital filtering, and sigma-delta DAC stages. This arrangement is suitable when a system accepts digital audio from a decoder, portable player, or digital audio processor and requires analog stereo outputs. The 99 dB SNR figure provides a concrete selection criterion when comparing audio-conversion stages, although system-level noise also depends on the supply, clock, analog output network, grounding, and downstream amplifier. Typical applications include portable audio equipment, video CD players, digital audio adapters, compact stereo systems, and embedded audio products. In each case, the important design question is whether the required input word length, sample rate, interface mode, supply arrangement, and analog output topology match the device and its application circuit. A key design consideration is to preserve clean analog and digital grounding while keeping the digital interface and clock signals away from sensitive analog output paths. Decoupling and output filtering should follow the manufacturer application guidance once the complete electrical data is available. This page synthesizes the verified distributor specifications, source links, and engineering context rather than adding unverified datasheet values. The verified distributor records identify Cirrus Logic as the current source brand and describe WM8725CGED as a 24-bit, 96 kHz, stereo, 14-SOIC audio DAC. LCSC also reports the part as in stock with a listed price of $1.0043, while current quantity pricing beyond that single source is not provided.

询价 有现货
WM8762CGED - 24-Bit 192kHz Stereo DAC | Cirrus Logic
WM8762CGED

WM8762CGED - 24-Bit 192kHz Stereo DAC | Cirrus Logic

Cirrus Logic WM8762CGED is a 24-bit stereo digital-to-analog converter IC operating up to 192 kHz and housed in an 8-pin SOIC package. Verified distributor data identifies it as a serial audio DAC with a 24-bit resolution, 192 kHz capability, and an 8-SOIC format. A DAC is a data-conversion semiconductor that transforms digital audio samples into left- and right-channel analog voltages. In the signal hierarchy, the WM8762CGED belongs to the digital-to-analog converter class, then to the ADC/DAC family and the broader signal-conversion and audio interface categories. Its stereo outputs are suited to audio playback paths in consumer, communications, and embedded audio systems. The verified data identifies three headline characteristics: 24-bit resolution, support for operation up to 192 kHz, and an 8-pin SOIC package. These values position the converter for designs requiring higher-resolution digital audio and a compact surface-mount footprint. The serial interface and stereo output architecture allow a digital audio source to feed two analog channels through one converter IC. The WM8762CGED family is identified in distributor listings as a Wolfson/Cirrus Logic audio DAC. Its practical implementation depends on the host audio interface, clocking scheme, analog output network, supply arrangement, and the format expected by the connected digital source. Exact pin names, voltage ratings, output architecture, and supported digital audio formats require confirmation from the manufacturer datasheet before PCB or firmware design. Typical audio uses include digital audio players, multimedia systems, communications equipment, and embedded sound-control platforms. In a player design, the converter would typically sit between the digital audio processor and an analog output stage feeding headphones or a line-input amplifier. The compact SOIC package can simplify routing where a small surface-mount footprint is important. Designers should verify the datasheet pinout, recommended decoupling, clock requirements, analog output connection, and supported operating conditions. Since the supplied data does not state supply voltage, pin functions, output mode, or digital interface details, those values are intentionally marked as data needed rather than inferred. This page separates verified distributor facts from engineering information that still requires datasheet confirmation. This page consolidates verified distributor references, package identity, audio-resolution information, and selection guidance. It does not treat generic cross-reference results as proof of drop-in replacement; engineering equivalence must be confirmed by package, pinout, electrical limits, and digital-interface compatibility.

USD $0.82 有现货
WM8783GED/V Stereo 98kHz Audio ADC | Cirrus Logic
WM8783GED/V

WM8783GED/V Stereo 98kHz Audio ADC | Cirrus Logic

Cirrus Logic WM8783GED/V is a stereo low-power audio analog-to-digital converter with a 98 kHz sampling rate and 24-bit I2S output, supplied in an 8-pin SOIC package. The verified manufacturer-family source describes it as a stereo low-power ADC, while the retrieved distributor data identifies the same device family for 96 kHz operation. It is designed for compact audio capture, playback, and mixed-signal systems requiring dual-channel conversion. An ADC is an analog-to-digital converter, a mixed-signal integrated circuit that converts continuously varying analog audio voltages into digital samples. In the broader component hierarchy, an audio ADC belongs to data converters, mixed-signal semiconductors, and signal-chain ICs. The WM8783GED/V therefore sits between an analog microphone or line input and a digital audio interface such as I2S. The principal verified features are stereo operation, a 24-bit conversion format, I2S digital output, and a family sampling-rate capability reported as 98 kHz in distributor material and 96 kHz in the Wolfson-family result. The device is identified as low power, making it relevant to embedded audio systems where power consumption, channel count, and board area constrain the architecture. The manufacturer-family datasheet source also indicates that the device is manufactured on a CMOS process and is ESD-sensitive. WM8783GED/V is suitable for digital recording front ends, USB audio adapters, industrial audio capture, portable audio equipment, and consumer audio systems. In each case, the stereo ADC can convert left and right analog inputs into digital samples for downstream processing or transmission. The I2S interface helps simplify connection to digital audio controllers, DSPs, and microcontrollers, although the host device must support the required clocking and framing format. When selecting this part, verify the exact electrical characteristics, analog input range, clock requirements, master or slave operating mode, and package pin assignment in the current manufacturer documentation. Do not infer those values from generic ADC descriptions. For replacement work, confirm that the candidate uses the same SOIC footprint and pin-to-pin signal arrangement rather than relying only on a similar sample rate or converter function. This page combines the verified source snippets for the WM8783GED/V family with engineering-oriented application and selection context. Because the retrieved data does not provide a complete current manufacturer product page, several detailed parameters remain explicitly marked for verification rather than being guessed.

USD $1.15 有现货
WM8960CGEFL/RV Stereo Codec with 1W Drivers | Cirrus Logic
WM8960CGEFL/RV

WM8960CGEFL/RV Stereo Codec with 1W Drivers | Cirrus Logic

The Cirrus Logic WM8960CGEFL/RV is a stereo audio codec with integrated Class-D speaker drivers, headphone drivers, and a microphone interface, designed for portable digital audio applications. The device is identified as a 24-bit stereo audio interface in a 32-QFN package measuring 5 x 5 mm, and the verified manufacturer-related data states that it provides 1 W per channel into 8-ohm loads with a 5 V supply. Its combination of digital audio conversion, analog input, headphone output, and integrated speaker amplification allows portable equipment to use one compact audio subsystem instead of separate codec and amplifier packages. A stereo audio codec is an interface IC that converts digital audio data into analog signals and converts analog microphone or line-level inputs back into digital audio data. The WM8960CGEFL/RV belongs to the broader audio interface and power-management hierarchy: audio codec, mixed-signal interface IC, semiconductor, and portable-audio signal-chain component. Its integrated Class-D speaker drivers target compact speaker solutions where PCB area, component count, and low power are important. The headphone drivers support personal-audio outputs, while the microphone interface supports portable voice and communication functions. Verified source data identifies the part as a stereo CODEC with 1 W stereo Class-D speaker drivers and headphone drivers for portable audio applications. The supplied DigiKey result identifies it as a 24-bit stereo audio interface in a 32-QFN 5 x 5 mm package. The WM8960CGEFL/RV is therefore suited to portable audio systems where the digital host interface, analog audio paths, and speaker amplification must coexist in one package. The exact sample rate, voltage range, control interface, and full pin-level electrical limits are not included in the supplied verified data and must be confirmed from the manufacturer datasheet before design release. A key design consideration is analog and power-supply layout. Digital audio clocks and control signals should be kept away from sensitive microphone and headphone paths, while the integrated speaker outputs require careful return-current routing and adequate power delivery. Decoupling must follow the manufacturer’s recommended values and placement because the codec combines digital, analog, headphone, and Class-D output functions in one package. Designers should also verify speaker impedance, load current, thermal conditions, and supply sequencing against the official datasheet before connecting external transducers. Typical uses include portable media players, compact audio accessories, personal-audio products, voice-enabled devices, and small speaker systems. This page consolidates the verified distributor descriptions, package information, identified audio functions, source links, and engineering guidance; it does not substitute unavailable electrical details with assumptions.

USD $10.96 有现货
WM9701CPT Stereo Audio Codec | Texas Instruments
WM9701CPT

WM9701CPT Stereo Audio Codec | Texas Instruments

The Texas Instruments WM9701CPT is a stereo audio codec with an integrated analog audio channel and digital audio interface, supplied in a 28-pin TQFP package. The verified distributor data identifies it as an Audio Special Purpose / Audio Channel device and lists an LCSC starting price of $0.6762. Its primary role is converting digital audio data into analog stereo signals while supporting audio-system signal conditioning and analog output control. The package designation CPT identifies a 28-pin TQFP-compatible physical format, but detailed electrical limits, supported sample rates, interface modes, analog performance, and pin functions are not present in the supplied verification records. A codec is an audio interface integrated circuit that combines digital-to-analog conversion, analog signal paths, and control or communication functions. In the broader semiconductor hierarchy, an audio codec belongs to an audio interface IC, then to an interface IC and a mixed-signal semiconductor. This integration can reduce the number of separate converters and support components in consumer audio, communications, and embedded systems. For the WM9701CPT, however, the supplied data does not establish whether its digital interface is I2C, I2S, or another format, nor does it quantify the number of supported channels. The verified records provide three useful procurement anchors: DigiKey Marketplace lists WM9701CPT for purchase and shipment, Octopart identifies availability and pricing across two distributors, and LCSC lists the part as in stock from $0.6762. A separate distributor listing describes the device as an analog consumer audio/video IC. These sources support commercial availability, but they do not provide manufacturer lifecycle status, operating temperature, supply voltage, clock requirements, DAC resolution, SNR, THD, output impedance, or pin-level mapping. WM9701CPT is best evaluated as a legacy or inventory-dependent audio codec rather than assumed to be a currently designed modern USB audio solution. Before schematic release, an engineer should obtain the original manufacturer datasheet and confirm the CPT land pattern, exposed-pad requirements, digital interface, analog routing, clocking, and firmware or register expectations. The part number alone is not enough to establish drop-in compatibility or modernization safety. Potential audio applications include legacy consumer-audio systems, portable media equipment, communications terminals, and embedded products that already target this codec family. Such uses remain conditional because the supplied data does not verify operating conditions or signal paths. Component selection should be based on a complete datasheet review rather than the distributor category label. The main engineering risk is assuming that similarly named stereo codecs are interchangeable. Digital-interface timing, register maps, analog routing, package dimensions, exposed-pad treatment, and software initialization can differ even when the functional description is similar. Validate the replacement against the original schematic and PCB footprint before committing to an alternative. This page consolidates the verified distributor listings, separates confirmed procurement facts from missing technical data, and avoids inventing specifications, pin assignments, or drop-in replacements. Obtain the authoritative datasheet before layout release or production substitution.

USD $0.68 有现货
WPC8763LDG - Embedded Controller IC QFP-128 | Winbond
WPC8763LDG

WPC8763LDG - Embedded Controller IC QFP-128 | Winbond

The Winbond Electronics WPC8763LDG is a specialized embedded controller (EC) integrated circuit supplied in a 128-pin QFP surface-mount package, designed primarily for notebook PC and mobile-system platform management applications such as keyboard scanning, power sequencing supervision, and thermal/fan control. An embedded controller is a specialized microcontroller that operates semi-independently of the host CPU to manage low-level platform functions. In the PC system hierarchy, the EC sits below the main CPU and chipset (PCH) as a power-management IC tier: it handles keyboard matrix scanning, battery charging supervision, thermal monitoring, fan speed control, and lid/power-button events, typically following Intel or AMD platform EC firmware specifications such as those used with ACPI and eSPI/KBC interfaces. The WPC8763LDG belongs to Winbond's WPC876x family of embedded controllers, which integrates an 8-bit or proprietary MCU core with on-chip flash/ROM program memory, keyboard controller (KBC) logic, GPIO, PWM channels for fan control, and ADC inputs for thermal and voltage monitoring. Key differentiating features of this family include the high GPIO count required for notebook keyboard matrices, integrated PWM fan controllers that reduce external component count, and low standby power consumption for battery-operated systems. The 128-pin QFP package provides sufficient I/O for a full notebook EC implementation on a single chip. Architecturally, EC devices like the WPC8763LDG combine a low-power MCU core, a shared RAM region, dedicated peripheral blocks (PS/2 keyboard interface, SMBus/I2C masters for battery and thermal IC communication, pulse-width modulators, and watchdog timers), and boot ROM. Firmware executes from internal non-volatile memory, and the EC communicates with the chipset over LPC or eSPI buses depending on platform generation. Typical applications include laptop and notebook motherboard EC functions, keyboard/mouse controller emulation (PS/2 KBC/Mouse), battery charging management in coordination with a charger IC, thermal and acoustic (fan) management, and general-purpose GPIO expansion in portable and industrial embedded systems. A key design consideration is firmware compatibility: the EC must run BIOS-coordinated firmware, so replacing this device requires both hardware pin compatibility and firmware/toolchain support - verify code image compatibility before any substitution. This page synthesizes distributor stock and pricing data, package information, and sourcing guidance not consolidated in the manufacturer's public datasheet listing.

USD $1.07 有现货
WT:A - Micron 48Gb LPDDR4 SDRAM Mobile Memory | Micron
WT:A

WT:A - Micron 48Gb LPDDR4 SDRAM Mobile Memory | Micron

Micron Technology MT53E1536M32D4DT-046 WT:A is a 48 Gbit Mobile LPDDR4 SDRAM memory IC in the MT53E family, rated at 2.133 GHz and supplied in a 200-ball TFBGA. According to DigiKey listing data retrieved on 2026-10-09, the part is a Mobile LPDDR4 device intended for high-density, low-power system designs that require the bandwidth of LPDDR4 with the smallest possible PCB footprint. What is an LPDDR4 SDRAM? LPDDR4 (Low-Power Double Data Rate 4) is a JEDEC-standardized volatile memory category optimized for mobile and power-constrained applications. Compared with LPDDR3 and DDR3/DDR4, LPDDR4 uses a low-swing I/O interface (V<sub>DDQ</sub> typically 1.1 V), 2n-prefetch architecture, and deep power-down modes, positioning it within the broader mobile memory hierarchy: LPDDR4 -> SDRAM -> volatile memory -> memory IC -> semiconductor. LPDDR4 is the memory type used in virtually every high-end smartphone application processor, and is increasingly adopted in automotive infotainment, edge AI, and ultra-thin notebooks. Key features of this 48 Gbit MT53E1536M32D4DT-046 WT:A device include a 1536M x 32-bit logical organization, 2.133 GHz data rate per the -046 speed-bin suffix, and operation from a low-voltage core rail to maximize battery life. The 200-ball TFBGA package is thin-profile and thermally efficient, suiting space-limited mobile platforms. The device supports the standard LPDDR4 command set including multi-channel operation, low-power states (IDD2N, IDD3P, IDD6), and on-die temperature sensing. The architecture follows Micron's 1y-nm-class mobile DRAM process, enabling a high-density 48 Gbit monolithic die. Combined with the -046 speed grade, this delivers the throughput needed for multi-camera image pipelines, 4K video encode/decode buffers, and large neural network inference workloads running on the application processor. The wide 32-bit datapath keeps channel-count low, simplifying PCB routing on highly integrated SoCs. Typical applications include flagship smartphone application processors, ultra-thin notebook main memory, automotive infotainment platforms, edge AI inference accelerators, AR/VR headset compute modules, and embedded single-board computer platforms. The wide temperature support and small form factor make it attractive in any design that demands high memory density with low standby power. When designing with the MT53E1536M32D4DT-046 WT:A, ensure the host SoC's LPDDR4 PHY matches the 2.133 GHz speed bin to avoid down-training. Decoupling and PCB stack-up should follow the Micron LPDDR4 design guide, with controlled-impedance routing for the CA and DQ byte lanes and matched lengths within each byte group. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a one-line distributor listing.

USD $9.85 有现货
X9313UST1 - 50kΩ 32-Tap Digital Potentiometer SOIC-8 | Renesas
X9313UST1

X9313UST1 - 50kΩ 32-Tap Digital Potentiometer SOIC-8 | Renesas

The Renesas X9313UST1 is a digitally controlled potentiometer (XDCP™) housed in an 8-pin SOIC package with a fixed end-to-end resistance of 50 kΩ and 32 resistive taps. It provides a single-channel, non-volatile, up/down wiper interface through three logic input pins (U/D, INC, CS) and stores the last wiper position through on-chip nonvolatile memory that retains setting across power cycles. The 32-tap resolution gives approximately 1.0% per-step resolution across the resistor array. Background context: a digital potentiometer (often abbreviated "digi-pot") is a solid-state, semiconductor replacement for a mechanical potentiometer or trim pot. Digi-pots sit within the broader data-acquisition and analog-signal-conditioning hierarchy, alongside DACs and digital rheostats, and they belong to the Renesas XDCP™ family. Unlike mechanical pots, they are programmable by host firmware, never wear from mechanical actuation, and ship in surface-mount packages suitable for reflow soldering and dense PCB layouts. Key features include a low 1 mA (typical) standby current, terminal voltages up to ±5 V across the resistor array, a 1.0% end-to-end resistance tolerance, and a wiper current rating up to approximately ±1 mA continuous, with peak surge handling to 10 mA. The 3-wire serial interface consumes only three MCU GPIO pins and is compatible with 5 V logic. The internal architecture pairs a polysilicon resistor array with CMOS wiper switches and a non-volatile memory cell that latches the last wiper position before power-down. Three control inputs (CS, INC, U/D) implement a step-and-direction interface: CS enables the chip, INC clocks each tap step, and U/D selects up or down direction. Power-on recall places the wiper on the stored value with deterministic behavior. Typical applications are audio volume/balance control, LCD contrast/brightness trimming, programmable voltage references, sensor calibration, and parameter-set storage where an MCU must hold a setting through power-down. Because the wiper retains state without external EEPROM, designers can eliminate a serial EEPROM and reduce BOM cost in many calibration circuits. When designing with the X9313UST1, respect the maximum terminal voltage (±5 V across the resistor terminals) and verify that pin 8 is correctly identified in PCB layout - the part is widely second-sourced and a small number of look-alike 8-pin digi-pots swap the GND and VL pin positions. Add a 0.1 µF decoupling capacitor close to the supply pin and confirm that CS is not allowed to float. This page combines the Renesas datasheet specifications, current distributor pricing, pin-compatible cross references, and practical layout notes not always covered in the original datasheet, providing engineers a single-page engineering brief for the X9313UST1.

USD $0.86 有现货
XA2S200E-6FT256I - 200K Gate FPGA | AMD | 256-FTBGA
XA2S200E-6FT256I

XA2S200E-6FT256I - 200K Gate FPGA | AMD | 256-FTBGA

The AMD XA2S200E-6FT256I is a member of the Spartan-IIE XA family of Field Programmable Gate Arrays (FPGAs), designed for automotive and industrial applications requiring high performance, abundant logic resources, and a rich feature set at a low cost. This device provides 200,000 system gates, 5,292 logic cells, and 1,176 Configurable Logic Blocks (CLBs), operating from a nominal 1.8V supply. It is housed in a 256-ball FTBGA (17x17 mm) package with 182 user I/O pins. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer or designer after manufacturing—hence "field-programmable." FPGAs are part of the broader programmable logic device (PLD) family, which sits above ASICs in flexibility but below them in unit cost at high volume. The Spartan-IIE family is a superior alternative to mask-programmed ASICs, avoiding the initial cost, lengthy development cycles, and inherent risk of conventional ASICs. FPGA programmability permits design upgrades in the field with no hardware replacement necessary. Key features of the XA2S200E-6FT256I include 57,344 total RAM bits, support for 1.71V to 1.89V supply voltage, and a -40°C to 100°C junction temperature range. The device uses a 0.15-micron CMOS process and supports I/O standards including LVCMOS, LVTTL, and HSTL. The -6 speed grade indicates a maximum internal clock frequency of approximately 200 MHz, suitable for moderate-speed control and data processing tasks. Technically, the Spartan-IIE architecture combines a configurable logic fabric with block RAM and dedicated routing resources. The 256-ball FTBGA package provides excellent thermal and electrical performance, with a compact 17x17 mm footprint. The device is lead-free and RoHS compliant, meeting modern environmental standards. Typical applications include automotive infotainment, motor control, industrial networking, and test equipment. The 182 I/O pins allow flexible interfacing with sensors, ADCs, and communication transceivers. The wide temperature range and automotive qualification make it suitable for under-hood and harsh-environment deployments. When designing with this FPGA, ensure adequate decoupling on the 1.8V core supply and separate I/O supply rails. The device is now obsolete (EOL), so plan for last-time buy or consider pin-compatible alternatives for new designs.

USD $29.00 有现货
XA3S1000-4FTG256Q - 1M Gate Automotive FPGA | AMD Xilinx
XA3S1000-4FTG256Q

XA3S1000-4FTG256Q - 1M Gate Automotive FPGA | AMD Xilinx

The AMD Xilinx XA3S1000-4FTG256Q is an automotive-grade Field Programmable Gate Array (FPGA) from the Spartan-3 XA family, designed for high-volume, cost-sensitive automotive electronic applications. It delivers 1,000,000 system gates, 17,280 logic cells, and 442,368 total RAM bits in a 256-ball FTBGA package. This device operates with a nominal supply voltage of 1.2V (range 1.14V to 1.26V) and supports 173 user I/O pins, making it suitable for a wide range of automotive control and interface tasks. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer or designer after manufacturing. Unlike fixed-function ASICs, FPGAs contain an array of programmable logic blocks and a hierarchy of reconfigurable interconnects that allow the hardware to be reprogrammed to perform any digital logic function. The Spartan-3 XA family is specifically optimized for automotive applications, meeting the rigorous AEC-Q100 qualification standard for reliability across extended temperature ranges (-40°C to +125°C). Key features of the XA3S1000-4FTG256Q include its automotive qualification (AEC-Q100), 173 user I/O pins, 1920 Configurable Logic Blocks (CLBs), and 442,368 total RAM bits. The device is built on 90nm technology and supports a maximum operating frequency of 125MHz. The FTG256 package (256-ball FTBGA) provides a compact footprint suitable for space-constrained automotive PCBs while offering adequate thermal performance for the device's power dissipation. From a technical architecture perspective, the Spartan-3 XA family uses a 90nm process technology with a 1.2V core voltage, enabling low power consumption while maintaining high logic density. The device includes dedicated multipliers, block RAM, and digital clock managers (DCMs) that support complex digital designs. The automotive-grade variant ensures operation across the full -40°C to +125°C temperature range, making it reliable for under-hood and in-cabin automotive electronics. Typical applications include automotive infotainment systems, engine control units (ECUs), advanced driver-assistance systems (ADAS), and industrial motor control. The device's 173 I/O pins and 1M gate capacity make it ideal for glue logic, sensor interfacing, and display control in automotive environments. When designing with this device, ensure proper power supply decoupling with 0.1uF and 10uF capacitors placed close to the VCC pins. The 1.2V core supply must be clean and stable; consider using a dedicated LDO or DC-DC converter with adequate ripple rejection to maintain reliable FPGA operation.

USD $28.94 有现货
XA7A100T-1FGG484Q - Automotive Artix-7 FPGA, 101K LE, 484-FCBGA | AMD
XA7A100T-1FGG484Q

XA7A100T-1FGG484Q - Automotive Artix-7 FPGA, 101K LE, 484-FCBGA | AMD

The AMD XA7A100T-1FGG484Q is an automotive-qualified Artix-7 XA Field-Programmable Gate Array (FPGA) with 101,440 logic cells, 4,976,640 system gates, and 4.75 Mbit of block RAM, housed in a 484-ball Fine-Pitch Chip-Scale BGA (FCBGA / FGG484) package. It integrates 15850 Adaptive Logic Modules (ALMs) and 285 user I/Os, supporting up to 4 transceivers at 6.25 Gb/s for high-speed serial links. An FPGA (Field-Programmable Gate Array) is a reconfigurable integrated circuit containing an array of programmable logic blocks, interconnect fabric, and dedicated silicon blocks (DSP, BRAM, transceivers, clock management) that designers program via HDL to implement custom digital logic, DSP pipelines, or interface bridges. FPGAs sit within the broader semiconductor hierarchy: programmable logic device -> logic IC -> integrated circuit -> semiconductor. The Artix-7 XA sub-family is AMD's automotive-temp (-40C to +125C) extension of the cost-optimized Artix-7 line, targeting AEC-Q100 Grade 2 qualified designs. Key features include 28 nm TSMC HPL process technology, 1.0 V core voltage (0.95 V Vccint option), support for DDR3-1066 memory interfaces, integrated PCIe Gen2 hard cores, and dedicated DSP48E1 slices for high-throughput arithmetic. The XA family adds automotive-grade qualification and extended temperature operation beyond the commercial XC7A100T. Architecturally, the device uses a 6-input LUT-based ALM fabric fed by a hierarchy of regional, horizontal, and clock backbone routing. 240 DSP48E1 slices deliver up to 528 GMACs of fixed or floating-point throughput at 28 nm, and integrated GTX transceivers support CPRI, 7-Series PCIe Gen2, and SRIO protocols up to 6.25 Gb/s. Typical applications include automotive driver-assistance (ADAS) sensor fusion, in-vehicle networking bridges (CAN/Ethernet/LIN), body-electronics controllers, infotainment video preprocessing, and industrial machine-vision pipelines. The XA prefix signals compliance with ISO 26262-relevant automotive design flows when used with the Vivado Design Suite. When designing with the XA7A100T-1FGG484Q, plan thermal dissipation for the 484-FCBGA (theta_JA around 14 C/W with proper airflow) and follow AMD UG475 pinout guidelines to avoid signal-integrity issues on GTX transceiver lanes. Use IBIS models and Vivado's power estimation before tape-out. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same Artix-7 XA family, and practical design notes not found in the manufacturer datasheet alone.

USD $120.10 有现货
XA7A12T-1CPG238I - Automotive Artix-7 FPGA | AMD
XA7A12T-1CPG238I

XA7A12T-1CPG238I - Automotive Artix-7 FPGA | AMD

The AMD XA7A12T-1CPG238I is an automotive-qualified Artix-7 XA Field Programmable Gate Array (FPGA) with 12,800 logic cells, 737,280 bits of block RAM, and 112 user configurable I/O pins. It is supplied in a 238-ball LFBGA/CSPBGA (CSBGA-238) package with a -1 speed grade and is designed for cost-sensitive automotive and industrial applications where low power, small footprint, and reprogrammable hardware logic are essential. An FPGA (Field Programmable Gate Array) is a semiconductor device containing a matrix of configurable logic blocks connected through programmable interconnects; the array can be reprogrammed in the field to implement user-defined digital logic circuits. FPGAs sit between fixed-function ASICs and software processors in the digital system hierarchy, giving engineers the ability to iterate hardware designs without silicon respin. The Artix-7 XA family is specifically screened for automotive quality, bringing FPGA flexibility to vehicle systems. Key features of the XA7A12T-1CPG238I include 12,800 logic elements, 737,280 total block RAM bits, and 112 user I/O in a compact 238-ball CSPBGA. The -1 speed grade offers an entry-level performance point that minimizes cost and power while supporting moderate clock rates for control, interface, and image-processing tasks. The device is RoHS compliant per LCSC listing, and the XA prefix indicates automotive-grade screening. Architecturally, Artix-7 devices integrate a high-performance programmable logic fabric, embedded block RAM, and DSP slices for arithmetic operations. The 737,280-bit block RAM supports distributed FIFOs and line buffers, while the flexible I/O cells connect to a wide range of single-ended and differential signalling standards. These capabilities enable deterministic hardware processing in ADAS, motor control, display bridging, and industrial logic applications. Typical applications include automotive ADAS sensor fusion, electric pump and fan motor control, industrial machine vision, in-vehicle display bridges, battery management safety logic, and UAV flight controllers. The 112 I/O and automotive qualification make the XA7A12T suitable for replacing multiple discrete logic and microcontroller tasks with one programmable device. When designing with the XA7A12T-1CPG238I, pay careful attention to multi-rail power sequencing requirements and the exact CPG238 pinout file. Multiple supply rails, BGA decoupling, and configuration flash selection are critical for first-pass success.

USD $25.20 有现货
XA7A12T-2CSG325I - Automotive Artix-7 FPGA 12.8K LC | AMD
XA7A12T-2CSG325I

XA7A12T-2CSG325I - Automotive Artix-7 FPGA 12.8K LC | AMD

The AMD Xilinx XA7A12T-2CSG325I is an automotive-qualified Artix-7 field programmable gate array (FPGA) in a 324-ball LFBGA/CSPBGA (CSG325) package. It provides 12,800 logic cells, 150 user I/O, and 737,280 bits of block RAM, with a -2 speed grade that supports high-performance, real-time processing in harsh environments. As part of the XA Artix-7 automotive family, this device delivers AEC-Q100-grade dependability and operates over an industrial temperature range. An FPGA (field-programmable gate array) is a semiconductor integrated circuit whose logic fabric can be configured after manufacturing using hardware description languages such as Verilog or VHDL. FPGAs occupy a unique position in the programmable logic hierarchy, combining hardware-level parallelism with reconfigurability and low-latency I/O. The Artix-7 architecture targets power-conscious, high-volume applications that need moderate logic density, rich I/O flexibility, and deterministic timing. Key feature highlights include 40 DSP48E1 slices for high-throughput multiply-accumulate signal processing, three clock management tiles (CMTs), and a 1.0 V core supply that reduces dynamic power. The -2 speed grade is ideal for 100-300 MHz interface and logic designs. The CSG325 package measures only 15 x 15 mm, with a 0.8 mm ball pitch that allows cost-effective 4-layer PCB routing. The device is JESD-609 e1 lead-free (SnAgCu finish), RoHS compliant, and MSL-3 rated with a 260 C peak reflow temperature. Architecturally, the device uses the proven 7-series SRAM-based fabric with 6-input LUTs, dual flip-flops per slice, and cascade chains for arithmetic. The internal block RAM can be configured as 36 Kb or 18 Kb primitives with multiple parity bits. The configuration engine supports master SPI, master BPI, slave SelectMAP, slave serial, and JTAG modes, providing flexible boot options for automotive and industrial systems. Typical applications are automotive ADAS pre-processing, sensor fusion gateways, industrial motor control, medical ultrasound front ends, networking line cards, broadcast video interfaces, and test equipment. The 150 user I/O with HR (high-range, 1.2 V to 3.3 V) capability lets designers interface directly to many sensors, ADCs, and memory devices without external level shifters. When designing with this device, follow AMD/Xilinx UG583 recommendations for BGA power decoupling: place 1.0 uF and 0.1 uF capacitors under the package on VCCINT, and ensure a monotonic, sequenced power-up of VCCINT, VCCBRAM, and VCCO for reliable configuration.

USD $44.90 有现货
XA7A50T-1CSG325Q - Automotive Artix-7 FPGA, 52K LC | AMD
XA7A50T-1CSG325Q

XA7A50T-1CSG325Q - Automotive Artix-7 FPGA, 52K LC | AMD

The AMD XA7A50T-1CSG325Q is an automotive-grade Artix-7 XA Field Programmable Gate Array (FPGA) IC delivering 52,160 logic cells, 150 user I/O, and 2,764,800 system gates in a 324-ball LFBGA (CSPBGA) package. The "XA" prefix designates AMD's automotive-qualified Artix-7 family, qualified per AEC-Q100 for harsh-environment deployments, while the "-1" speed grade and "Q" suffix denote the standard temperature tier with automotive qualification. The device is fabricated on a 28nm high-k metal-gate (HKMG) low-power process, balancing performance-per-watt with cost-effectiveness for volume automotive and industrial designs. A Field Programmable Gate Array (FPGA) is a semiconductor integrated circuit composed of configurable logic blocks (CLBs), programmable interconnect, and dedicated silicon IP blocks such as transceivers, block RAM, and DSP slices. Within the broader programmable logic hierarchy, the Artix-7 family sits at the low-power, cost-optimized tier below Kintex-7 and Virtex-7, targeting high-volume, power-sensitive applications. The XA7A50T occupies the mid-density position in the XA Artix-7 lineup and is engineered to replace discrete ASICs and ASSPs in automotive driver assistance, infotainment, and industrial control systems. Key features include 2,764,800 system gates, 52,160 logic cells, 2,700 Kbits of block RAM distributed across 75 36-Kbit BRAMs, 120 DSP48 slices for fixed- and floating-point arithmetic, and 4 GTP transceivers capable of up to 6.6 Gb/s line rate. The fabric supports clock management tiles (CMTs) for high-precision frequency synthesis, with up to 64 I/O standards including LVDS, HSTL, SSTL, and 1.5V/1.8V/2.5V/3.3V LVCMOS. Programmable logic resources are accompanied by an integrated configuration controller that supports master/slave SelectMAP, JTAG, and SPI flash boot modes. Architecturally, the device leverages 6-input LUTs for logic optimization and dedicated carry chains for high-speed arithmetic. The XA qualification adds extended temperature testing, PPAP documentation, and longevity support matching automotive program lifecycles. Power is managed through a dedicated core voltage rail (1.0V VCCINT) and separate I/O bank supplies (VCCO), enabling mixed-voltage interfacing on a single die. Typical applications include automotive driver assistance (ADAS) sensor fusion, surround-view camera processing, vehicle networking gateways, industrial motor control, factory automation, and portable medical imaging. The wide operating temperature and automotive qualification make it particularly suited for under-hood ECUs and zonal architectures. When designing with the XA7A50T-1CSG325Q, follow AMD's Kintex/Artix-7 PCB layout guidelines for power decoupling — at least 24 low-ESL 0.1µF capacitors around the BGA, plus bulk 47–100µF ceramic on each power rail. The 324-LFBGA requires microvia or via-in-pad PCB technology for reliable assembly. This page synthesizes distributor pricing, AEC-Q100 automotive qualification details, drop-in Artix-7 alternatives, and PCB design guidance not aggregated in the manufacturer datasheet.

USD $195.00 有现货
XA7A75T-2CSG324I - Automotive Artix-7 FPGA | AMD
XA7A75T-2CSG324I

XA7A75T-2CSG324I - Automotive Artix-7 FPGA | AMD

AMD XA7A75T-2CSG324I is an automotive-grade Artix-7 field-programmable gate array in a 324-terminal LFBGA package, with 210 I/O, 75,520 logic cells, and a 387,072-bit fabric presented in the verified distributor data. The device combines programmable logic, fixed resources, and automotive-oriented temperature grading in a 28 nm FPGA platform. Its -2 speed grade favors performance over the -1 grade, while the XA prefix identifies the automotive Artix-7 family. An FPGA is a semiconductor whose digital function is configured after manufacture. A field-programmable gate array belongs to the broader logic-device hierarchy: FPGA, programmable-logic IC, digital semiconductor, and embedded computing component. Instead of relying solely on fixed application-specific logic, an FPGA integrates configurable lookup logic, programmable routing, block resources, memory, and I/O into one reconfigurable device. Verified listings identify 210 I/O, 75,520 logic cells, and 387,072 fabric bits. The searchable Artix-7 product page states that the family uses a 28 nm process and targets high performance per watt. Additional performance figures such as clock rate, block-RAM capacity, DSP resources, power, and temperature limits were not supplied in the verified input and therefore are not inferred here. The 324-LFBGA package supports dense PCB integration but requires exact land-pattern, ball-map, and assembly-process control. Verified distributor data separately describes the package as 324-LFBGA or CSPBGA. AMD publishes package pinout files in TXT and CSV formats, giving engineers the authoritative ball assignments needed for PCB and design-signoff work. Potential uses include automotive sensing, vehicle communication, industrial image processing, embedded control, and high-throughput digital logic. Suitability depends on the complete AMD Artix-7 datasheet, selected tools, automotive qualification requirements, temperature grade, resource utilization, timing closure, and system power budget. A robust design should begin with the AMD package-pinout files, preserve all required power and configuration pins, and constrain every interface against the appropriate device-speed and automotive qualification constraints. Use Vivado or another AMD-supported implementation flow for constraints, synthesis, implementation, timing analysis, and bitstream generation. This page consolidates verified distributor identity, package, resource, and sourcing data with replacement analysis and implementation guidance. It does not infer unprovided electrical ratings, pricing, stock status, or full ball assignments; those fields remain explicitly separated from verified facts.

询价 有现货
XA7S25-1CSGA324I - Spartan-7 FPGA, 150 I/O | AMD
XA7S25-1CSGA324I

XA7S25-1CSGA324I - Spartan-7 FPGA, 150 I/O | AMD

The AMD XA7S25-1CSGA324I is a member of the Spartan-7 XA family of Field Programmable Gate Arrays (FPGAs), designed for automotive and industrial applications requiring high performance and reliability. It features 23,360 logic cells, 3,650 adaptive logic modules (ALMs), and 1.58 Mbit of block RAM, providing ample resources for moderate-complexity digital designs. The device is housed in a 324-ball CSGA (Chip-Scale BGA) package with 150 user I/O pins, supporting a core voltage of 0.95V to 1.05V and operating over a temperature range of -40°C to +100°C. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer or designer after manufacturing—hence "field-programmable." FPGAs consist of an array of programmable logic blocks, interconnects, and I/O blocks, allowing them to implement any digital logic function. They are a subset of programmable logic devices (PLDs) and sit within the broader category of embedded processors and controllers. FPGAs are distinct from microcontrollers and ASICs because they offer reconfigurability, enabling rapid prototyping and in-field updates. Key features of the XA7S25-1CSGA324I include 150 user I/Os, 1.58 Mbit of block RAM, and support for various I/O standards such as LVCMOS, LVDS, and SSTL. The device is AEC-Q100 qualified, making it suitable for automotive electronics. It also supports partial reconfiguration and has built-in security features like AES bitstream encryption. The CSGA-324 package offers a compact footprint with a 0.8mm ball pitch, ideal for space-constrained designs. Technically, the Spartan-7 family is built on a 28nm process, balancing performance and power efficiency. The XA7S25 includes DSP slices for signal processing, clock management tiles (CMT) with PLLs and MMCMs, and high-speed transceivers (though this specific variant does not include GTP transceivers). The device supports configuration via JTAG, SPI, or BPI interfaces, and can be programmed using AMD's Vivado Design Suite. Typical applications include automotive driver assistance systems (ADAS), industrial motor control, machine vision, and communication interfaces. The XA7S25's combination of logic density, I/O count, and automotive qualification makes it ideal for these environments. When designing with this FPGA, ensure proper decoupling of the core and I/O supplies, and follow the layout guidelines in UG475 for the CSGA package. The device requires a 1.0V core supply and 1.8V/2.5V/3.3V I/O supplies, depending on the bank configuration.

USD $33.50 有现货
XA7Z020-1CLG400Q - Automotive Zynq-7000 SoC with Artix-7 FPGA | AMD
XA7Z020-1CLG400Q

XA7Z020-1CLG400Q - Automotive Zynq-7000 SoC with Artix-7 FPGA | AMD

The AMD XA7Z020-1CLG400Q is an automotive-grade Zynq-7000 XA System-on-Chip (SoC) integrating a dual-core ARM Cortex-A9 MPCore processor with CoreSight debug, an Artix-7 FPGA fabric containing 85K logic cells, and 6.25 Gb/s transceivers, packaged in a 400-ball CSPBGA (CLG400, 17x17 mm, 0.8 mm pitch). It targets AEC-Q100 Grade 2 operating conditions (-40C to +105C Tj) for automotive driver assistance, infotainment, and industrial vision systems. An SoC FPGA (System-on-Chip with FPGA fabric) is a class of heterogeneous computing device that combines a hardened Application Processor (APU) subsystem with programmable logic on a single die. The ARM Cortex-A9 cluster runs up to 667 MHz in this speed grade, executing an OS (typically Linux or AUTOSAR) while the Artix-7 PL accelerates parallel DSP, sensor fusion, and custom interfaces. This architecture sits within the broader hierarchy of embedded processors -> microcontroller/MPU -> SoC FPGA -> heterogeneous compute platform. Key device highlights include 53,200 LUTs, 560 Kbit block RAM, 220 DSP48E1 slices, and 200 user I/O pins. The processing system adds a NEON media engine, single/double-precision FPU, L1/L2 caches, and a rich peripheral set (USB 2.0, Gigabit Ethernet, SD/SDIO, CAN 2.0B, UART, SPI, I2C). Hard PCIe Gen2 x4 controllers, 32-bit DDR3/DDR3L memory controller, and 4 high-speed serial transceivers enable high-bandwidth interfaces. From an architectural perspective, the device is built on a 28 nm HPL process with separate PS and PL power domains, allowing the processor to operate while the FPGA fabric is held in reset (or vice versa). The 667 MHz Cortex-A9 in the -1 speed grade is the slowest in the Zynq family (versus the -2 grade at 866 MHz), trading some CPU throughput for cost savings in non-throughput-critical designs. Typical automotive applications include surround-view ADAS camera fusion, automotive Ethernet gateways, HMI/infotainment controllers, and motor-control servo drives. Industrial uses range from machine vision over GigE Vision to deterministic EtherCAT controller nodes. A key design consideration is power-tree sequencing - PS and PL each require dedicated 1.0V core and 1.8V/2.5V/3.3V auxiliary rails, and the PS must boot first through a dedicated configuration process. This page synthesizes DigiKey distributor pricing, parametric cross-references, and practical design notes not found in the standalone datasheet PDF.

USD $132.10 有现货
XC2287M104F80LRABKXUMA1 - 16/32-Bit 80MHz 832KB Flash MCU | Infineon
XC2287M104F80LRABKXUMA1

XC2287M104F80LRABKXUMA1 - 16/32-Bit 80MHz 832KB Flash MCU | Infineon

The Infineon XC2287M104F80LRABKXUMA1 is a 16/32-bit C166SV2 XC22xxM family microcontroller integrating a CISC/DSP/RISC processing core running at 80 MHz with 832 KB of on-chip Flash and 58 KB RAM, supplied in a 144-pin PG-LQFP-144-4 package with exposed pad. It targets automotive and industrial powertrain, body, and chassis applications requiring deterministic real-time response combined with DSP-grade signal processing throughput on a single die. A microcontroller (MCU) is a single-chip processing subsystem that integrates a CPU core, program and data memory (Flash, ROM, RAM), peripheral interfaces (ADC, timers, communication buses), and power management. Within the broader semiconductor taxonomy, MCUs sit inside Embedded Processors and Controllers, alongside microprocessors (MPUs) and system-on-chips (SoCs); they are typically selected over MPUs when deterministic latency, low power, and tight BOM integration matter more than raw application-processor performance. The C166S V2 core inherits the classic C166 instruction set with DSP extensions and RISC-like single-cycle execution, placing this part in the legacy 16-bit automotive MCU segment alongside derivatives such as the XC2764X and XC2336D families. Key features of the XC2287M104F80LRABKXUMA1 include 832 KB program Flash, 58 KB SRAM, an on-chip 10-bit ADC with up to 118 channels per the JLCPCB catalog listing, an operating voltage range of 3.0 V to 5.5 V, and an industrial-grade temperature range of -40 °C to +125 °C. The 80 MHz C166S V2 core is paired with a MAC (multiply-accumulate) unit, enabling single-cycle DSP operations suitable for sensor signal conditioning and field-oriented motor control. The LQFP-144 package with exposed pad supports an external thermal pad for improved heat dissipation in power-dense automotive ECUs. Architecturally, the XC2287M pairs two independent on-chip peripherals: a MultiCAN module with up to five CAN nodes for automotive network integration, plus USART, SSC, and I2C interfaces for sensor and actuator links. The integrated Peripheral Event Controller (PEC) enables DMA-style peripheral-to-memory transfers, allowing CPU background time for high-rate ADC-to-memory capture without interrupt overhead. Combined, this peripheral mix makes the part appropriate for multi-bus automotive ECUs where CAN-FD-class networking, deterministic ADC sequencing, and DSP-class signal processing are all required on one chip. Typical applications include automotive body control modules (BCM), electric power steering (EPS) motor controllers, HVAC blower/temperature control, instrument cluster signal processing, and industrial servo/motor control. Designers also deploy the XC2287M in industrial inverter front-ends and CAN-connected sensor hubs. When selecting this part, verify that your toolchain supports the C166S V2 instruction set and that the chosen compiler (e.g., Keil C166, TASKING, iSystem winIDEA) generates code for the C166S V2 core; pin-compatible Infineon XC2286/2288 family members can be substituted with only Flash capacity differences for shorter code footprints. The exposed pad must be soldered to the PCB ground plane for thermal and electrical performance. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes that complement, but do not replace, the Infineon XC228xM datasheet.

USD $11.10 有现货
XC2C256-7TQG144C - 256-Macrocell 6.7 ns CPLD | AMD
XC2C256-7TQG144C

XC2C256-7TQG144C - 256-Macrocell 6.7 ns CPLD | AMD

The AMD XC2C256-7TQG144C is a CoolRunner-II complex programmable logic device with 256 macrocells, a 6.7 ns propagation delay, and 118 I/O pins in a 144-pin TQFP package. It provides approximately 6000 gates of logic for compact programmable control, interface, and signal-routing designs. A complex programmable logic device, or CPLD, is a programmable-logic semiconductor that combines interconnected macrocells with programmable interconnect. In the broader hierarchy, a CPLD is a programmable logic device and an FPGA alternative. Unlike mask-programmed logic, a CPLD permits design changes without fabricating a new integrated circuit. The CoolRunner-II architecture also uses nonvolatile configuration storage, allowing the programmed logic to remain available after power is removed. The XC2C256 family provides 16 logic array blocks and 256 macrocells according to the available product data. Its -7 speed designation corresponds to the reported 6.7 ns propagation-delay class. With 118 user I/O pins, it supports parallel external interfaces and board-level control functions. The 1.7 V to 1.9 V internal supply range is suitable for systems designed around the device's documented core operating conditions. Typical uses include industrial control, communications equipment, portable electronics, programmable interface logic, bus arbitration, and compact control-plane functions. The CPLD can consolidate multiple fixed-function gates into one programmable device, reducing board area compared with a larger gate-array implementation when the required logic is modest. Designers should still verify timing, power, I/O standards, and pin constraints against the complete CoolRunner-II datasheet and their specific design. The principal design consideration is tool and configuration compatibility. Existing CoolRunner-II projects depend on supported AMD or Xilinx programming tools, device support, and verified bitstream compatibility. Before replacing an installed device, engineers must check the exact package, speed grade, temperature grade, power behavior, and pin assignment rather than relying only on the family name. This page consolidates the supplied distributor and manufacturer information, distinguishes verified facts from unavailable specifications, and adds selection and sourcing guidance. Because the provided data does not include a complete pin table, electrical limit table, or qualified replacement list, those fields remain explicitly marked for engineering review.

询价 有现货
XC2C64A-7QFG48I - 64-Macrocell CoolRunner-II CPLD, 7ns | AMD/Xilinx
XC2C64A-7QFG48I

XC2C64A-7QFG48I - 64-Macrocell CoolRunner-II CPLD, 7ns | AMD/Xilinx

The AMD/Xilinx XC2C64A-7QFG48I is a 64-macrocell, 1.8V CoolRunner-II Complex Programmable Logic Device (CPLD) with 4.6 ns pin-to-pin propagation delay, housed in a 48-pin QFG (QFN) surface-mount package. The device belongs to the CoolRunner-II family, which combines low static power (~15 µA quiescent current) with non-volatile flash configuration memory and in-system programmability via IEEE 1149.1 JTAG. A CPLD (Complex Programmable Logic Device) is a non-volatile, instant-on programmable logic device that sits between discrete glue logic and FPGAs in the programmable logic hierarchy (CPLD -> PLD -> programmable logic -> digital IC -> semiconductor). CoolRunner-II devices implement logic in function blocks based on PLA (Programmable Logic Array) sub-blocks with macrocell flip-flops, providing deterministic timing that simplifies design sign-off in glue-logic applications. Key features of the XC2C64A-7QFG48I include 64 macrocells organized as 4 logic blocks of 16 macrocells, 33 usable I/O pins (out of 37 total), 1.5K usable gates, a pin-to-pin delay of 4.6 ns at industrial temperature range, and DataGATE technology for per-pin input signal blocking to reduce dynamic power. The 0.18 µm CMOS process enables 1.8V core operation with I/O tolerance to 3.3V signals, simplifying interfacing with legacy 3.3V peripherals. The architecture combines a deterministic timing model with low-power 1.8V operation, making this CPLD well-suited for portable and battery-powered designs. The internal 1.8V VCCINT and I/O banked VCCIO supply rails permit mixed-voltage signaling without external level shifters, while the four global clock networks and per-macrocell OE controls give designers flexible clocking and bus-management options. Typical applications include portable/battery-powered consumer electronics where low quiescent current matters, industrial control I/O expansion and bus bridging (I2C, SPI, UART glue logic), and telecom infrastructure glue logic interfacing 3.3V peripherals to 1.8V processors. Designers also deploy this part in medical handheld devices and white goods motor control boards. When designing with this device, ensure the JTAG chain length and TDO load remain within specifications if multiple CoolRunner-II parts share one chain. The DataGATE feature can be disabled per pin to preserve dynamic behavior on critical paths; verify per-pin signal integrity when chaining long busses. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

USD $2.40 有现货