集成电路

子分类

📁 ADC/DAC 3,100+ 产品 📁 放大器IC 1,700+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 640+ 产品 📁 Comparator ICs 1 产品 📁 DSP 1,100+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 7,100+ 产品 📁 接口IC 3,000+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 450+ 产品 📁 存储IC 870+ 产品 📁 微控制器 20,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（38,000+)

TLV3011AIDCKR - 5µA Open-Drain Comparator w/ 1.24V Ref | SC70-6 | TI
TLV3011AIDCKR

TLV3011AIDCKR - 5µA Open-Drain Comparator w/ 1.24V Ref | SC70-6 | TI

The Texas Instruments TLV3011AIDCKR is a micropower comparator with an integrated 1.242 V series voltage reference, packaged in a 6-pin SC-70 (DCK) footprint. It is an open-drain output variant of the TLV3011 family with a maximum quiescent current of 5 µA, input common-mode range that extends 200 mV beyond both supply rails, and single-supply operation from 1.8 V to 5.5 V. The on-chip voltage reference exhibits low 100 ppm/°C drift over temperature, making the part suitable for battery-monitoring and threshold-detection circuits where a stable reference is required without an external Zener or shunt. A comparator is an analog building block that compares two input voltages and produces a digital logic output indicating which one is larger. The TLV3011 family belongs to the open-drain comparator hierarchy, where the output transistor only sinks current and requires an external pull-up resistor to the desired logic rail. This contrasts with push-pull comparators like the TLV3012, which actively drive both high and low. Open-drain comparators are preferred when level-shifting is needed between logic domains, when wired-OR logic combining multiple comparator outputs is desired, or when the output must swing above VCC. Key features include 5 µA maximum quiescent current, 1.242 V reference with 100 ppm/°C drift, internal hysteresis for clean switching, and propagation delay in the microsecond range suitable for low-speed monitoring. The SC-70-6 package measures approximately 2.0 x 1.25 mm, allowing placement in space-constrained wearables, IoT sensor nodes, and portable battery-management boards. The wide input common-mode range (rail-to-rail minus 200 mV margin) supports monitoring of signals at or near the supply rails, which simplifies battery-voltage detection in single-cell Li-ion systems down to 3.0 V cut-off. Typical applications include battery voltage monitoring, window comparators for over-voltage/under-voltage detection, threshold detectors in portable medical devices, industrial sensor alarms, and simple relaxation oscillators. The internal reference enables a single-chip solution for generating a fixed threshold without adding external shunt regulators. When designing with this part, choose the external pull-up resistor on OUT to match the desired logic-rail rise time and current; 100 kΩ to 1 MΩ values are typical. Ensure the reference output capacitor (if used at REF pin) is sized to filter reference noise without slowing response. The open-drain output allows combining multiple TLV3011 outputs for wired-OR fault signalling in redundant-supply monitor circuits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
TLV316QDBVRQ1 - 10MHz RRIO Op Amp, AEC-Q100, SOT-23-5 | TI
TLV316QDBVRQ1

TLV316QDBVRQ1 - 10MHz RRIO Op Amp, AEC-Q100, SOT-23-5 | TI

The Texas Instruments TLV316QDBVRQ1 is an automotive-grade, single-channel, 10-MHz, rail-to-rail input/output (RRIO) CMOS operational amplifier in a 5-pin SOT-23 (DBV) package. It operates from 1.8 V to 5.5 V single supply, delivers 10 MHz gain-bandwidth product, 400 µA/channel quiescent current, and 12 nV/√Hz input voltage noise density at 1 kHz, making it a strong general-purpose low-voltage op amp for cost-sensitive signal chains. An operational amplifier (op amp) is a high-gain DC-coupled differential amplifier that uses external feedback to set its closed-loop behavior - gain, bandwidth, input impedance, and output impedance. Op amps form the fundamental building blocks of analog signal conditioning: inverting/non-inverting amplifiers, active filters, integrators, comparators, transimpedance amplifiers, and current/voltage buffers. Within the broader signal-chain taxonomy, general-purpose CMOS op amps sit between low-power chopper/zero-drink amplifiers and high-speed current-feedback op amps, optimized for portable, battery-powered, and automotive sensor-interface applications. Key features of the TLV316QDBVRQ1 include rail-to-rail input common-mode range that includes both supply rails, rail-to-rail output swing within tens of millivolts of either rail, 1.8 V minimum supply enabling direct Li-ion/cell operation, 400 µA typical quiescent current per channel, and 12 nV/√Hz voltage noise density at 1 kHz. AEC-Q100 Grade 1 qualification (-40 °C to +125 °C ambient), HBM ESD Class 3A, and CDM ESD Class C5 ratings make it suitable for under-hood and cabin automotive modules. Internally the device uses a CMOS input stage that supports true rail-to-rail common-mode operation without the crossover-distortion artifacts of legacy bipolar RRIO parts. The 10-MHz gain-bandwidth product combined with 6 V/µs typical slew rate provides sufficient speed for moderate-bandwidth sensor conditioning, audio pre-amplification, and active filter stages at audio frequencies. Typical applications include automotive sensor signal conditioning (current-shunt monitors, thermistor bridges, pressure/temperature transducers), body and chassis ECUs, infotainment audio pre-amplifiers, low-side/battery current sensing, and portable/mobile precision buffers. The wide supply range also supports industrial 3.3 V and 5 V PLC analog input modules. When designing with this op amp, place a 0.1 µF decoupling capacitor within a few millimeters of the supply pin, use a feedback network that keeps total gain above the minimum stable gain of 1 V/V (unity), and observe the input common-mode range - although RRIO, the input stage shifts distortion performance near the rails, so biasing the input mid-supply preserves linearity. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical PCB design notes that go beyond the manufacturer datasheet to accelerate automotive and industrial analog front-end design decisions.

询价 联系我们
TLV3201AIDCKR - 40ns microPOWER Comparator, SC-70-5 | Texas Instruments
TLV3201AIDCKR

TLV3201AIDCKR - 40ns microPOWER Comparator, SC-70-5 | Texas Instruments

The Texas Instruments TLV3201AIDCKR is a single-channel, 40 ns microPOWER push-pull comparator in a 5-pin SC-70 (DCK) package, drawing only 40 µA of quiescent current. It features rail-to-rail input common-mode range, 1 mV typical input offset voltage, and a wide 2.7 V to 5.5 V single-supply operating range. The push-pull CMOS output stage delivers large output drive current without requiring an external pull-up resistor. A comparator is an analog circuit building block that compares two input voltages and forces its output to one of two logic states based on which input is larger. The TLV3201 belongs to the high-speed, low-power comparator sub-category of analog comparators, which sits within amplifiers/comparators -> analog ICs -> signal conditioning -> power management. This combination of 40 ns propagation delay and 40 µA supply current places the part at the high-speed / low-power boundary, making it attractive for battery-powered systems that also need fast overvoltage detection or threshold-crossing response. Key features include 40 ns propagation delay (typical), 40 µA quiescent current, rail-to-rail input common-mode range that can swing 200 mV below the negative rail, push-pull CMOS output capable of driving typical CMOS or TTL loads directly, internal hysteresis for clean switching in noisy environments, and an industrial -40 °C to +125 °C operating temperature range. The small SC-70-5 (2.0 × 2.1 mm) footprint enables compact designs for space-constrained applications. The TLV3201 is built on a CMOS process with a precision input stage that achieves 1 mV input offset while maintaining microamp quiescent current. The push-pull output eliminates the static current draw of an open-drain pull-up resistor, improving efficiency in battery-powered systems. The wide 2.7 V to 5.5 V supply range supports both 3.3 V and 5 V rails commonly used in industrial and consumer designs. Typical applications include battery management threshold detection, zero-crossing detectors for line-powered systems, oscillator circuits, window comparators, IR receiver signal conditioning, and general-purpose analog monitoring. The part is particularly well suited for portable and handheld equipment where the 40 µA supply current extends battery life while the 40 ns speed supports fast fault response. When designing with this comparator, account for input source impedance and bias current to limit offset-induced errors. For high-speed switching above 100 kHz, add local supply decoupling (0.1 µF ceramic in parallel with 1 µF bulk) within 5 mm of the VCC pin. The internal 6 mV hysteresis is sufficient for most noisy environments, but for very slow-moving inputs add external positive feedback to widen the hysteresis band. This page synthesizes distributor pricing, drop-in alternatives in the same SC-70-5 footprint, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
TLV3202AQDGKRQ1 - 40ns Dual Automotive Comparator | TI
TLV3202AQDGKRQ1

TLV3202AQDGKRQ1 - 40ns Dual Automotive Comparator | TI

The Texas Instruments TLV3202AQDGKRQ1 is a dual, high-speed, low-power automotive comparator with 40 ns propagation delay, a 40 µA per-channel quiescent current, and rail-to-rail inputs in an 8-VSSOP DGK package. It operates from a single 2.7 V to 5.5 V supply and supports an ambient operating-temperature range of -40 °C to 125 °C. The device is designed for fast threshold decisions where response time, low power, and compact placement matter. A comparator is a differential signal integrated circuit that compares two input voltages and switches its logic output according to their relationship. In the broader semiconductor hierarchy, this dual analog comparator belongs to the comparator, interface IC, and signal-conditioning categories. The TLV3202-Q1 family combines rail-to-rail input capability, 1 mV offset voltage, push-pull outputs, and large output-drive capability, making it useful for signal conditioning, threshold detection, and system monitoring. The most important verified features are 40 ns high-speed response, 40 µA low-power operation, rail-to-rail input, 1 mV offset voltage, and large output drive current. Its two channels share one package, reducing board area for paired decisions. The push-pull output can drive downstream digital logic directly, while the low-power operating current helps preserve system power budget in continuously monitoring designs. The automotive-oriented Q1 designation also makes the device appropriate for temperature-qualified vehicle systems when its specified operating range and qualification requirements are satisfied. The TLV3202AQDGKRQ1 is supplied in an 8-VSSOP DGK surface-mount package. Its compact footprint is suitable for dense industrial, automotive, communications, and embedded-control designs. The package and pin configuration must be compared directly against the original PCB footprint before substitution; a similar comparator function alone does not guarantee drop-in compatibility. The manufacturer product page identifies the device as a dual comparator with eight pins and a -40 °C to 125 °C temperature range. Typical applications include automotive battery and signal monitoring, industrial threshold detection, sensor conditioning, overvoltage and undervoltage indication, waveform edge detection, and general-purpose digital decision logic. The fast 40 ns response helps minimize uncertainty when a signal crosses the comparator threshold, while the low-power characteristic is advantageous in battery-powered or continuously active systems. Designers should verify input common-mode limits, output logic levels, supply decoupling, and unused-channel handling against the manufacturer datasheet. Place the device near the sensed signal where practical, maintain a stable reference node, and route high-current or switching nodes away from comparator inputs. This page combines the verified manufacturer and distributor information with engineering guidance, application context, and a conservative replacement assessment.

询价 联系我们
TLV320AC37CN - 3V Voice-Band Audio Processor | Texas Instruments
TLV320AC37CN

TLV320AC37CN - 3V Voice-Band Audio Processor | Texas Instruments

The TLV320AC37CN is a voice-band audio processor (VBAP) from Texas Instruments, designed for single 3-V operation with low power consumption. It integrates a combined A/D, D/A converter and filters, supporting sample rates up to 16 kHz and a pass-band to 7.2 kHz. The device is housed in a 20-pin PDIP package, making it suitable for through-hole assembly in telecommunication and audio applications. A voice-band audio processor (VBAP) is a specialized mixed-signal IC that combines analog-to-digital and digital-to-analog conversion with filtering and signal processing optimized for the 300 Hz to 3.4 kHz voice band. It sits within the broader category of audio codecs, which are essential in telephony, intercoms, and voice-controlled systems. The TLV320AC37CN specifically targets low-power, battery-operated voice applications, offering a complete analog front-end and codec in a single package. Key features include a low operating power of 20 mW typical, standby mode at 5 mW, and power-down mode at 2 mW. The device supports extended variable-frequency operation with sample rates up to 16 kHz and a pass-band to 7.2 kHz. It includes an electret microphone interface, making it ideal for direct connection to electret condenser microphones. The combined A/D, D/A, and filters simplify system design by reducing external components. Technically, the TLV320AC37CN employs a CMOS process and operates from a single 3-V supply, which is critical for portable and battery-powered equipment. The device features a PCM codec interface with A-law companding, suitable for digital telephony standards. The through-hole PDIP-20 package ensures easy prototyping and manual assembly, though it limits high-density applications compared to surface-mount alternatives. Typical applications include digital telephone answering machines, speakerphones, intercom systems, and voice recorders. The low power consumption and 3-V operation make it particularly suited for battery-powered devices where efficiency is paramount. The integrated filters and codec reduce BOM cost and board space. When designing with this device, ensure proper decoupling of the 3-V supply and careful layout of the analog and digital sections to minimize noise coupling. The device is now obsolete, so consider pin-compatible alternatives for new designs.

询价 联系我们
TLV320AIC3105IRHBR - Low-Power Stereo Audio CODEC | Texas Instruments
TLV320AIC3105IRHBR

TLV320AIC3105IRHBR - Low-Power Stereo Audio CODEC | Texas Instruments

The Texas Instruments TLV320AIC3105IRHBR is a low-power stereo audio CODEC with 6 single-ended inputs, 6 outputs, an integrated stereo headphone amplifier, and enhanced digital effects, housed in a 32-pin VQFN (RHB) 5x5 mm package. It integrates stereo 24-bit ADC and DAC paths with a PCM digital interface (I2S/left-/right-justified DSP/PCM) for portable audio and telephony designs. What is a stereo audio CODEC? A CODEC (coder-decoder) combines an analog-to-digital converter (ADC) and digital-to-analog converter (DAC) in a single device, supporting both microphone-record and headphone/speaker-playback paths. In the system hierarchy, the CODEC sits between the application processor (which runs audio software) and the analog transducers (microphones and speakers), translating between the digital audio stream and real-world acoustic signals. Stereo means two independent channels (left + right), as opposed to mono. Key features include a wide range of programmable I/O gain stages, single-ended or fully-differential output configurations, integrated PLL for flexible clock generation, and extensive register-based power control. The headphone amplifier provides ground-centered output for capless headphone connection, reducing BOM cost and PCB area. Programmable 3D, bass boost, and treble/midrange digital effects are executed inside the DSP core, offloading the host processor. Architecturally, the TLV320AIC3105 uses multi-bit sigma-delta ADCs and DACs with low-latency digital filters for natural audio reproduction. Three separate supply rails (analog 2.7V-3.6V, digital core 1.525V-1.95V, digital I/O 1.1V-3.6V) allow direct connection to a 1.8V host processor I/O while keeping the analog section on a clean 3.3V rail, which improves dynamic range and reduces digital switching noise coupling into the audio path. Typical applications include portable media players, smartphones, Bluetooth/USB audio dongles, headphone amplifiers, dictation/recording devices, and VoIP headsets. The wide input gain range and microphone biasing make it equally suited to handset and headset use cases; the small 5x5 mm QFN footprint enables compact wearable form factors. A common design tip is to keep the analog supply decoupling star-grounded to the headphone return path to minimize click/pop on enable transitions. The vendor recommends sequencing the analog supply before the digital I/O supply to avoid latch-up and to use the built-in PGA soft-mute ramps during power-up/power-down. This page synthesizes XAIPART pricing, drop-in alternatives, and practical design notes that complement - but do not replace - the manufacturer datasheet.

询价 联系我们
TLV320AIC3106IRGZT - Low-Power Stereo Audio CODEC | TI
TLV320AIC3106IRGZT

TLV320AIC3106IRGZT - Low-Power Stereo Audio CODEC | TI

The Texas Instruments TLV320AIC3106IRGZT is a low-power stereo audio CODEC with 10 inputs, 7 outputs, integrated headphone amplifier, and enhanced digital effects, housed in a 48-pin VQFN (RGZ) 7x7 mm package. It supports 16/20/24/32-bit PCM data at sample rates from 8 kHz to 96 kHz with 102 dBA signal-to-noise ratio on the DAC path, and operates from a 1.8 V digital supply plus a 3.3 V analog supply, consuming as little as 15 mW during stereo 48 kHz DAC playback. An audio CODEC (coder-decoder) is an integrated circuit that converts between digital audio streams and analog microphone/line/headphone signals, combining an ADC input path and DAC output path inside a single chip. The TLV320AIC3106 sits in the broader hierarchy of audio interface ICs -> interface ICs -> integrated circuits, and is widely deployed in portable, battery-powered, and space-constrained designs where low power, stereo playback, and integrated headphone drive are required simultaneously. Multiple line, microphone, and headphone amplifiers share an extensive register-based power-control interface, enabling fine-grained energy management as system use cases change. Key features of the TLV320AIC3106 include stereo 24-bit ADC and DAC with 102 dBA SNR, integrated 40 mW headphone amplifier, programmable 3D / bass / treble / EQ digital effects, and selectable single-ended or fully-differential analog inputs. The digital serial audio bus supports I2S, left-justified, right-justified, and DSP/PCM modes for flexible connection to virtually any application processor or DSP. An automatic gain control (AGC) block on the ADC path keeps microphone levels stable across varying speech distances. At the architectural level the device pairs a multi-bit delta-sigma modulator front end with on-chip FIR and IIR engine blocks so that tone control, EQ, and de-emphasis are applied digitally without burdening the host processor. PLL-based clock generation accepts common 12, 13, 24, or 27 MHz system clocks and derives all internal timing from them, simplifying board layout by removing the need for a dedicated audio master crystal in many designs. Extensive register-based power control keeps unused analog blocks powered down until audio paths are activated. Typical applications span portable media players, portable navigation devices, mobile phones and VoIP handsets, portable gaming, digital still cameras and camcorders, ultrasonic imaging, IP phones and USB headsets, as well as portable audio docks and Bluetooth speakers. The combination of low power, integrated headphone drive, and rich on-chip digital effects makes it equally suitable for stereo playback and full-duplex voice-capture products. When designing with this part, ensure both the 1.8 V digital and 3.3 V analog rails are well decoupled close to the IC, and that the PLL reference clock is selected to match the chosen MCLK frequency in software. Because the device supports both single-ended and differential microphone paths, designers should populate the unused input pins according to the datasheet reference circuit rather than leaving them floating. This page synthesizes distributor pricing, drop-in alternatives, and practical design considerations for the TLV320AIC3106IRGZT and its sibling variants into a single design-oriented reference beyond the raw manufacturer datasheet.

询价 联系我们
TLV320AIC3110IRHBT - Low-Power Audio Codec with Class-D Amp | TI
TLV320AIC3110IRHBT

TLV320AIC3110IRHBT - Low-Power Audio Codec with Class-D Amp | TI

The TLV320AIC3110IRHBT is a low-power, highly integrated audio codec from Texas Instruments, featuring a stereo audio DAC and a mono audio ADC, along with a 1.3W stereo Class-D speaker amplifier. It supports 32-bit audio data and communicates via I2C or serial interface. The device is housed in a 32-pin VQFN (5x5 mm) package, making it suitable for space-constrained portable applications. An audio codec is a device that encodes and decodes digital audio data, converting between analog and digital domains. It typically includes ADCs and DACs, along with signal processing and amplification stages. In a system hierarchy, an audio codec sits between the digital audio processor (e.g., DSP or SoC) and the analog audio output (speakers, headphones) or input (microphones). It is a critical component in portable electronics, automotive infotainment, and IoT devices. Key features of the TLV320AIC3110 include a 1.3W stereo Class-D speaker amplifier, which provides high efficiency for battery-powered devices. The device supports a wide analog supply range of 2.7V to 3.6V, a digital core supply of 1.525V to 1.95V, and a digital I/O supply of 1.1V to 3.6V. It also includes a programmable digital sine-wave generator and extensive register-based power control for optimizing power consumption. Technically, the TLV320AIC3110 integrates a low-power stereo DAC with 32-bit resolution and a mono ADC, supporting sample rates up to 96 kHz. The Class-D amplifier delivers 1.3W per channel into 8 ohms with low distortion. The device features a 5x5 mm VQFN package with exposed thermal pad for improved heat dissipation. It operates over the industrial temperature range of -40°C to +85°C. Typical applications include portable audio players, smartphones, tablets, and IoT devices requiring high-quality audio playback and recording. The integrated Class-D amplifier eliminates the need for an external amplifier, reducing BOM cost and board space. The I2C control interface allows easy integration with microcontrollers and DSPs. When designing with this device, ensure proper decoupling of the analog and digital supplies, and place the Class-D amplifier output filters close to the device to minimize EMI. The thermal pad should be soldered to a copper pour for effective heat dissipation.

询价 联系我们
TLV342ID - Dual 5.5V 2.2MHz RRO Op Amp | Texas Instruments
TLV342ID

TLV342ID - Dual 5.5V 2.2MHz RRO Op Amp | Texas Instruments

The Texas Instruments TLV342ID is a dual, low-voltage CMOS operational amplifier with rail-to-rail output swing, 5.5 V maximum supply capability, and 2.2 MHz gain-bandwidth performance. The device is supplied in an 8-pin SOIC package and provides two amplifiers per package, making it suitable for compact dual-channel signal-conditioning designs. The verified product information identifies the TLV342 as a low-voltage, low-power, rail-to-rail-output CMOS operational amplifier family. A CMOS operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while using high-impedance inputs and CMOS-compatible low-power characteristics. The TLV342 family belongs to the broader operational-amplifier hierarchy: op amp -> analog IC -> amplifier IC. Its rail-to-rail output architecture is useful when the usable signal range must extend close to the positive or negative supply rail, while the low-voltage operation suits battery-powered, portable, industrial-control, sensor-interface, and low-voltage signal-chain systems. Verified manufacturer information states that the TLV34xx family includes low-voltage, low-power devices with rail-to-rail output swing. The supplied family data also identifies PMOS input-stage characteristics including 1 pA typical input bias current and 0.3 mV typical offset voltage, although those figures should be checked against the specific ordering information and grade. The TLV342ID is identified as a dual circuit in 8-SOIC, while the family also includes single and dual variants. The product page describes the TLV342 as a dual 5.5 V, 2.2 MHz operational amplifier. Typical applications include low-voltage sensor conditioning, buffered analog measurements, audio and communication signal paths, current-loop interfaces, and general-purpose dual-amplifier circuits. The SOIC package provides a familiar surface-mount footprint, but the exact pin names and electrical limits must be taken from the manufacturer datasheet before layout or replacement qualification. Because the available verified snippets do not provide the complete price schedule, pin table, package drawing, or all electrical limits, those fields are marked as data needed rather than inferred. For robust design practice, verify the supply-voltage range, input common-mode range, output swing, unity-gain stability, input capacitance, shutdown behavior, and exposed thermal conditions in the applicable Texas Instruments datasheet. Do not treat rail-to-rail output as proof that the input common-mode range reaches either supply rail. Confirm the exact TLV342ID pinout and PCB land pattern before substituting any part. This page combines verified product descriptions, source links, application guidance, and explicit data gaps to support engineering comparison without fabricating unavailable specifications.

询价 联系我们
TLV3701IDBVR - Nanopower Push-Pull Comparator | Texas Instruments
TLV3701IDBVR

TLV3701IDBVR - Nanopower Push-Pull Comparator | Texas Instruments

The Texas Instruments TLV3701IDBVR is a single-channel nanopower push-pull comparator in a 5-pin SOT-23 (DBV) package, drawing only 560 nA per channel of supply current. It operates from a 2.7 V to 16 V single supply and features an input common-mode range that exceeds both supply rails by 200 mV, with 18 V reverse-battery protection on the inputs. A comparator is an analog circuit that compares two input voltages and produces a digital output indicating which is larger; the push-pull CMOS output stage of the TLV3701 drives a rail-to-rail logic level without an external pull-up resistor. As a member of the comparator family within the broader signal-chain IC hierarchy, the TLV3701 belongs to the nanopower class, designed specifically for ultra-low quiescent current applications where battery life is paramount. Key features include 560 nA quiescent current per channel, a typical propagation delay of 22 microseconds at 5 V, 18 V input tolerance with reverse-battery protection, and CMOS push-pull output capable of driving standard CMOS or TTL loads directly. The device also integrates ESD protection cells on the pins exceeding 2 kV HBM, and the SOT-23-5 package occupies only 2.9 mm x 1.6 mm of board area, enabling high-density PCB layouts. Technically, the TLV3701 uses a CMOS architecture with an internal bandgap reference for the threshold, an input stage tolerant of rail-to-rail common-mode swings, and a symmetrical push-pull output driver. The slow 22 us propagation delay is the deliberate trade-off for achieving sub-microamp quiescent current; the part is not suited for high-speed signal conditioning but is engineered for monitoring tasks that change state infrequently. Typical applications include battery voltage monitoring in wireless sensor nodes, low-frequency threshold detection in portable medical devices, micropower window comparators, system reset supervision, and battery-powered security sensors. The wide 2.7-16 V supply range also makes it suitable for industrial 24 V (nominal) line monitoring when divided down by external resistors. When designing with this device, place a 0.1 uF bypass capacitor within 2 mm of the VCC pin and minimize input trace lengths to reduce parasitic coupling. The slow propagation means it should not be used in fast closed-loop control, but for monitoring battery voltage or generating wake-up signals in IoT devices, the 560 nA supply current is the headline advantage. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page, giving engineers an actionable comparison set for nanopower comparator selection.

询价 联系我们
TLV376IDBVR - 5.5MHz RRIO Op Amp | Texas Instruments | Precision
TLV376IDBVR

TLV376IDBVR - 5.5MHz RRIO Op Amp | Texas Instruments | Precision

The Texas Instruments TLV376IDBVR is a 5.5-MHz, 100-µV offset, 8-nV/√Hz noise, 815-µA precision operational amplifier in a 5-pin SOT-23 package, built on TI's e-trim technology. It features rail-to-rail input and rail-to-rail output (RRIO) operation, 5.5-MHz gain-bandwidth product, 2-V/µs slew rate, and 1.2-mA quiescent current. The device operates from a single supply of 2.25 V to 5.5 V (or ±1.125 V to ±2.75 V). An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, used as the fundamental building block of analog signal conditioning. Within the broader taxonomy, op amps belong to linear integrated circuits -> amplifiers -> analog ICs -> semiconductors. The TLV376 specifically sits in the precision low-noise sub-category, optimized for dc accuracy plus moderate-speed ac performance - bridging the gap between zero-drift instrumentation amps and general-purpose CMOS op amps. Key features include 125-µV maximum input offset voltage, 8-nV/√Hz input voltage noise density at 1 kHz, 5.5-MHz unity-gain bandwidth, 2-V/µs slew rate, and rail-to-rail input and output swing. The e-trim trim architecture achieves dc precision comparable to chopper-stabilized parts without the chopping artifacts, while keeping the noise floor low enough for transducer and audio front-end designs. The TLV376 uses a CMOS input stage with e-trim digital offset correction performed at wafer probe, plus a bipolar-style class-AB output stage capable of driving 1 kΩ loads to within 50 mV of either rail. The combined architecture yields a low-power precision op amp suitable for battery-powered instrumentation. Typical applications include battery-powered instrumentation, sensor signal conditioning (thermocouple, RTD, bridge amplifiers), handheld test equipment, audio front-ends, and active filters. Its low quiescent current makes it attractive for always-on IoT sensor nodes. When designing with the TLV376, observe the input common-mode range: although specified rail-to-rail, linearity degrades within 1 V of either rail - keep inputs in the linear region (0 to V+ minus 1 V) for best THD. Decouple V+ with a 0.1-µF ceramic bypass capacitor placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not found in the standalone datasheet, helping engineers evaluate the TLV376IDBVR against competing precision op amps.

询价 联系我们
TLV3801 - 225ps LVDS High-Speed Comparator | Texas Instruments
TLV3801

TLV3801 - 225ps LVDS High-Speed Comparator | Texas Instruments

The Texas Instruments TLV3801 is a 225-ps high-speed comparator with complementary LVDS outputs, operating from a single 2.7 V to 5.25 V supply or a split supply of ±1.35 V to ±2.625 V, with a toggle frequency up to 3 GHz. It is packaged in an 8-pin WSON (DSG) 2x2 mm package for space-constrained designs. A comparator is an electronic circuit that compares two input voltages and outputs a digital signal indicating which is larger. The TLV3801 belongs to the high-speed comparator subclass, optimized for minimal propagation delay and high toggle rates. It sits within the analog-to-digital interface hierarchy, bridging analog signals to LVDS digital logic levels for downstream FPGAs and CPUs. Key features include a 225-ps propagation delay, complementary LVDS outputs that reduce EMI and suppress common-mode noise, and low power consumption of about 6.5 mW at 3.3 V. An enable pin supports power management and rail sequencing. The LVDS output stages drive standard LVDS inputs directly at up to 3 GHz toggle frequency. The device is built on a bipolar process with a differential input stage and LVDS output drivers, delivering deterministic, low-jitter switching. It is specified over the industrial temperature range of -40C to +125C, and an automotive-grade TLV3801-Q1 variant is available for AEC-Q100 applications. Typical applications include LIDAR pulse detection, where every nanosecond of propagation delay affects range resolution, high-speed differential line receivers for data transmission, and optical sensor modules. Clock recovery and fast data acquisition systems also benefit from the high toggle rate. Design tip: terminate the LVDS outputs with 100 ohm differential impedance and decouple each supply pin with 0.1 uF capacitors placed as close to the device as possible to preserve signal integrity.

询价 联系我们
TLV4112ID - 2.7MHz High-Output-Drive Rail-to-Rail Op Amp | TI
TLV4112ID

TLV4112ID - 2.7MHz High-Output-Drive Rail-to-Rail Op Amp | TI

The Texas Instruments TLV4112ID is a dual, high-output-drive operational amplifier with rail-to-rail output capability, a 2.7 MHz unity-gain bandwidth, and a 1.5 V/us slew rate. It is supplied in an 8-pin SOIC (D) package and is specified for a 6 V maximum supply voltage. The verified product data identifies the TLV4112 family as a family of high-output-drive operational amplifiers, with output currents exceeding 300 mA at 5 V. This output capability allows standard-pinout amplifiers to be used as high-current buffers or in coil-driver applications. The TLV4112ID is a dual general-purpose amplifier version, while TLV4110 and TLV4113 family members include shutdown functionality. Its 8-SOIC configuration makes it suitable for conventional analog signal-conditioning boards where a dual amplifier is required and a high-current output stage is useful. The rail-to-rail output helps preserve signal swing when operating near the supply rails, while the wide bandwidth supports applications requiring moderate-speed closed-loop performance. Engineers should still verify the exact input common-mode range, output swing, noise, offset, and stability requirements against the manufacturer datasheet before finalizing a design. TLV4112ID is relevant to low-voltage analog systems, sensor interfaces, buffer stages, current or voltage buffering, and coil-driver circuits. The device is not an SOA-rated power semiconductor, so SOA data is not applicable.

询价 联系我们
TLV4112IP - Dual High-Output-Drive Rail-to-Rail Op Amp | Texas Instruments
TLV4112IP

TLV4112IP - Dual High-Output-Drive Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments TLV4112IP is a dual, high-output-drive operational amplifier with rail-to-rail output, 2.7 MHz unity-gain bandwidth, and 1.5 V/us slew rate in an 8-pin PDIP package. It can deliver output current in excess of 300 mA at 5 V while operating from a supply as low as 2.7 V, making it suitable for buffer, line-driver, and coil-driver circuits that exceed the current capability of many conventional op amps. An operational amplifier is a differential voltage amplifier that uses feedback to control gain and drive an input signal accurately. The TLV4112 belongs to the voltage-feedback operational-amplifier family, with each channel providing high input impedance, signal amplification, impedance conversion, or closed-loop control. Its rail-to-rail output stage is especially useful when the required output swing must approach the positive or negative supply rail. Key characteristics include output current above 300 mA at 5 V, a 2.7 MHz unity-gain bandwidth, and a 1.5 V/us slew rate. The device is specified for a 6 V maximum supply voltage and consumes approximately 700 uA per channel. These characteristics distinguish it from general-purpose dual op amps intended mainly for low-current analog signal-conditioning applications. The high-current output stage allows the TLV4112 to act as a standard operational-amplifier buffer or drive a load directly without a separate output buffer. Its unity-gain bandwidth of 2.7 MHz supports moderate-frequency signal paths, while the 1.5 V/us slew rate helps preserve large-signal response. Because the output can source and sink substantial current, power dissipation and output-stage stability require careful attention at low output voltages or into capacitive loads. Typical uses include headphone and line-output buffers, relay and solenoid drivers, low-voltage motor drivers, signal-conditioning stages, and general dual-amplifier modules. The shutdown feature mentioned for other members of the TLV411x family is not attributed to the TLV4112, so control logic should not assume that a shutdown input is available on this exact device. For PCB design, place input and output decoupling capacitors close to the appropriate supply pins, provide a low-impedance return path, and verify stability with the intended load. Keep copper away from sensitive input nodes when the output is driving substantial current, and verify that the power-supply topology can accommodate the required output-current transients. This page combines manufacturer specifications, application-oriented guidance, pin-package information, and a structured comparison with closely related amplifier options. It is intended to help engineers evaluate output drive, bandwidth, supply range, package compatibility, and board-level implementation requirements before selecting a device.

询价 联系我们
TLV4113CD - Dual High-Drive R-R Op Amp | Texas Instruments
TLV4113CD

TLV4113CD - Dual High-Drive R-R Op Amp | Texas Instruments

Texas Instruments TLV4113CD is a dual, general-purpose operational amplifier with rail-to-rail output, high output-drive capability, and shutdown in a 14-SOIC package. Its headline characteristics include output current above 300 mA at 5 V, a 2.7 MHz nominal unity-gain bandwidth, a minimum slew rate of 0.55 V/µs, and a nominal common-mode rejection ratio of 63 dB. The maximum input offset voltage is 4000 µV, making the device suitable for buffer, amplifier, and coil-driver circuits that require more output current than a conventional low-power operational amplifier. An operational amplifier, commonly shortened to op amp, is an analog signal-conditioning semiconductor that amplifies the voltage difference between its differential inputs. The TLV4113 belongs to the operational-amplifier family, amplifier IC category, and broader analog semiconductor hierarchy. Rail-to-rail output allows the output voltage to approach the positive and negative supply limits, while the shutdown function can place the device into a low-power state when the application no longer requires active operation. Key features include two amplifier channels in one package, shutdown support, output currents in excess of 300 mA at 5 V, and a standard 14-SOIC footprint. The 2.7 MHz unity-gain bandwidth supports higher-frequency signal paths than a low-bandwidth precision or micropower amplifier. Its 0.55 V/µs minimum slew rate improves large-signal response, while 63 dB nominal common-mode rejection helps attenuate signals common to both inputs. The high-drive architecture is the central technical distinction of the TLV4113 family. According to the Texas Instruments TLV4113 product page, the amplifiers can source or sink more than 300 mA at 5 V, allowing standard op-amp pinouts to serve as high-current buffers or in coil-driver applications. This drive capability supports low-impedance loads without requiring an external output stage, although sustained high current increases power dissipation and requires careful PCB thermal design. Typical uses include audio output stages, low-impedance buffers, transducer drivers, relay or solenoid interfaces, and industrial control-signal conditioning. The device is particularly relevant when a conventional dual op amp lacks the current capability to drive a load directly. Shutdown can also reduce consumption in intermittently operating systems, provided the shutdown logic and timing are checked against the device requirements. For PCB design, use a solid ground return, place input and decoupling capacitors close to their associated pins, and preserve adequate copper around the package for thermal dissipation. Verify output-current limits, supply voltage, load transients, and stability with the selected feedback network. Because output drive is a core feature rather than an incidental specification, calculate worst-case dissipation before assigning the amplifier to a continuous-load position. This page combines the manufacturer's functional description with verified package and parametric details, application guidance, engineering design notes, and strictly same-package replacement information. It is intended to support faster part selection while keeping package, electrical, sourcing, and lifecycle checks explicit.

询价 联系我们
TLV5580IPWG4 - 8-Bit 80 MSPS Low-Power ADC | Texas Instruments
TLV5580IPWG4

TLV5580IPWG4 - 8-Bit 80 MSPS Low-Power ADC | Texas Instruments

The Texas Instruments TLV5580IPWG4 is an 8-bit, 80 MSPS low-power analog-to-digital converter (ADC) with a pipelined architecture, housed in a 28-pin TSSOP (PW) package rated for the industrial -40C to +85C temperature range. The part delivers 700 MHz typical analog input bandwidth, internal top/bottom reference voltages, and an adjustable full-scale reference input for flexible system calibration. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples a continuous analog waveform and produces a discrete binary code proportional to the input amplitude. The TLV5580 belongs to the pipelined ADC family, which sits in the hierarchy: ADC -> data converter -> data acquisition IC -> mixed-signal semiconductor. Pipelined ADCs use multiple low-resolution stages to achieve high sample rates at modest power, making them a standard choice for IF-sampling communications, CCD imaging, and digital oscilloscope front ends. Key features of the TLV5580 include 80 MSPS maximum sampling rate, single 3.3 V supply operation, 3.3 V TTL/CMOS-compatible digital I/O that simplifies interface to modern FPGAs and ASICs, an internal bottom-plate reference that reduces external component count, and an adjustable reference input for gain trim. The 700 MHz analog input bandwidth supports undersampling architectures where the ADC digitizes IF frequencies well above Nyquist. The 28-TSSOP (PW) footprint is pin-compatible across the broader TLV/TLC ADC family from Texas Instruments. Architecturally the device uses a multi-stage pipeline with internal sample-and-hold and digital error correction. The combination of 80 MSPS and 8-bit resolution keeps per-conversion power low (single-digit mA from a 3.3 V rail), which is the original design target: applications where the ADC must sit on the same board as noisy digital logic without dominating the power budget. The TLV5580 has been replaced by the ADS831 in TI's portfolio but remains specified and available for legacy designs. Typical applications include CCD imaging digitizers, video capture front ends, IF-sampling communications receivers, portable battery-powered instrumentation, and digital oscilloscope input stages. In each case the part provides a compact, low-power, single-supply path from analog to digital. When designing with the TLV5580, decouple AVDD and DVDD separately close to the package and follow standard pipelined-ADC layout practice: keep analog input traces short, use a ground plane under the analog input, and provide a clean 3.3 V rail. The PW suffix indicates tube packaging; the device is also offered in tape and reel as TLV5580IPWR.

询价 联系我们
TLV5590ED - 2-Bit FLEX Pager ADC | Texas Instruments
TLV5590ED

TLV5590ED - 2-Bit FLEX Pager ADC | Texas Instruments

The Texas Instruments TLV5590ED is a 2-bit analog-to-digital converter designed for FLEX pager chipset signal processing, supplied in a 14-pin small-outline package. It operates from a single supply as low as 2.7 V and uses a proprietary conversion method. The device supports peak and valley detection, selectable dual-bandwidth filtering, fast-track and slow-track operating modes, hold, and standby operation. According to the available manufacturer datasheet information, the associated filtering provides a selectable 1 kHz or 2 kHz bandwidth, each specified with ±5% tolerance, and uses a three-pole Butterworth low-pass response. An analog-to-digital converter is an interface IC that converts continuously varying analog signals into digital codes for processing, measurement, or control. A 2-bit ADC can represent four quantization levels, making it appropriate for compact control and detection systems rather than precision instrumentation. In the TLV5590 application, the converter operates inside a FLEX pager chipset alongside a compatible decoder and external peak or valley detection circuitry. Its position in the hierarchy is ADC, data-conversion IC, interface IC, semiconductor. Key features include the 2-bit proprietary-method conversion, support for both peak and valley detectors, selectable dual-bandwidth audio filtering, and a low-power standby mode. Fast-track mode supports rapid acquisition, slow-track mode supports a different measurement update behavior, and hold preserves the converter state when needed. Standby reduces activity when the pager is not receiving or processing useful signal information. The single-supply operation down to 2.7 V also helps the device fit compact, battery-powered pager designs. Technically, the TLV5590ED is part of a mixed analog and digital signal-processing chain. Its analog input is conditioned by filtering and detection circuitry before conversion. The resulting digital representation is intended for comparison and control within the chipset rather than high-resolution signal capture. The manufacturer datasheet describes the operating modes and their functional roles, but the supplied search data does not expose the complete timing table, transfer function, input impedance, or absolute maximum ratings; those details must therefore be confirmed in the original document before design release. Typical applications include FLEX-format pagers, battery-operated two-way messaging terminals, compact receiver modules, and legacy FLEX chipset designs requiring the TLV5591 decoder. In such systems, the converter supports peak and valley level detection while the selectable filter bandwidth can be matched to the modulation and receiver characteristics. Standby operation is particularly useful where average battery consumption matters more than continuous conversion. The primary design consideration is that this is a specialized 2-bit converter rather than a general-purpose high-resolution ADC. PCB implementation should preserve the package pin assignments and supply-decoupling recommendations in the manufacturer datasheet. Before substituting a different converter, engineers must verify package, pinout, input range, output coding, timing, filter response, and chipset protocol compatibility; a generic ADC with similar resolution may not be interchangeable. This page consolidates the verified product identity, distributor availability, datasheet-linked operating features, and substitution constraints for the TLV5590ED. It also distinguishes documented characteristics from parameters that remain unavailable in the retrieved data, reducing the risk of treating a legacy pager ADC as a generic precision converter.

询价 联系我们
TLV5593VF Telecom Roaming Decoder IC | Texas Instruments
TLV5593VF

TLV5593VF Telecom Roaming Decoder IC | Texas Instruments

Texas Instruments TLV5593VF is a telecom interface integrated circuit associated with the TMS320FLEX family of messaging-system solutions and an alphanumeric roaming decoder. The available verified information identifies the device as a Telecom IC and places it in the broader Texas Instruments interface-controller portfolio. It is offered in bulk packaging according to distributor indexing data. No verified package drawing, electrical rating table, operating-temperature range, pin configuration, or dimensional drawing was supplied for TLV5593VF. A telecom interface IC is a semiconductor category used to connect messaging or telephone-network equipment to control logic, codecs, memory, and system buses. Within the product hierarchy, the TLV5593VF belongs to integrated circuits, then interface ICs, then telecom-interface controllers. Its association with the TMS320FLEX family and alphanumeric roaming decoding indicates a role in receiving, organizing, or presenting telecommunications signaling information, although the exact channel architecture and host-interface protocol require confirmation from the original manufacturer documentation. The verified distributor listing calls TLV5593VF an alphanumeric roaming decoder, making message-signaling and roaming-message handling the principal functional distinction available from the supplied records. The listed manufacturer is Texas Instruments, and the indexed series designation is 900228-TLV5593VF. The JLCPCB listing separately classifies the device as a telecom interface IC and associates it with RoHS information. These classifications distinguish it from general-purpose DSPs, memory devices, and ordinary logic ICs. Because detailed electrical and timing values were not included in the verified material, engineers should not assume operating voltage, clock frequency, memory size, signaling rate, output current, or thermal limits. The appropriate procedure is to obtain the original Texas Instruments data sheet, functional description, pinout, and errata before schematic capture or PCB release. Rochester Electronics and DigiKey list the part for acquisition, while several other distributors provide datasheet links or quote routes, indicating fragmented legacy supply rather than a broad modern catalog position. Typical design uses for this device include telecom signaling systems, alphanumeric paging or messaging platforms, roaming-message decoding systems, and TMS320FLEX-based embedded communications equipment. These application descriptions follow the verified TMS320FLEX messaging-system and alphanumeric roaming-decoder classifications. Interface timing, supply sequencing, bus direction, reset behavior, and any external memory requirements must be checked against the original device documentation before the IC is connected to surrounding circuitry. The principal design caution is verification completeness. Because the supplied records do not establish the exact package, pin count, pin names, or electrical limits, a footprint should not be copied from a visually similar TMS320 device. PCB designers should use the manufacturer drawing, verify pin 1 orientation, confirm exposed-pad requirements, and plan decoupling only after obtaining the authoritative data sheet. This page intentionally distinguishes confirmed distributor facts from parameters still requiring engineering verification. This page consolidates the verified distributor classification, sourcing links, TMS320FLEX relationship, package-format reference, lifecycle caveat, and traceable comparison fields for TLV5593VF. It also separates confirmed facts from missing technical data and avoids presenting unsupported electrical specifications or unverified cross-reference parts as production-ready drop-in alternatives.

询价 联系我们
TLV5617A - Dual 10-Bit DAC, 2.7-5.5V | Texas Instruments
TLV5617A

TLV5617A - Dual 10-Bit DAC, 2.7-5.5V | Texas Instruments

The TLV5617A is a dual 10-bit voltage output digital-to-analog converter (DAC) from Texas Instruments, designed for low-power and space-constrained applications. It operates from a single 2.7V to 5.5V supply and features a flexible 3-wire serial interface compatible with TMS320, SPI, QSPI, and Microwire serial ports. The device is available in an 8-pin SOIC package (TLV5617AID) and includes a power-down mode to conserve energy. A digital-to-analog converter (DAC) is an electronic circuit that converts digital binary data into an analog voltage or current. The TLV5617A is a voltage-output DAC, meaning it produces a voltage proportional to the digital input. It is part of the broader family of data converters, which are essential in mixed-signal systems where digital processing must interface with the analog world. DACs are used in applications such as audio playback, motor control, and sensor calibration. Key features of the TLV5617A include dual 10-bit resolution, programmable settling time (fast mode: 3 µs, slow mode: 10 µs), and a rail-to-rail output buffer with Class-AB stage. The device also offers a power-down mode that reduces quiescent current to 1 µA, making it ideal for battery-powered equipment. The serial interface accepts a 16-bit word consisting of 4 control bits and 10 data bits, allowing flexible configuration. The TLV5617A uses a resistor-string architecture with a x2 gain rail-to-rail output buffer, ensuring low glitch energy and monotonic performance. The output buffer can drive capacitive loads up to 100 pF without external compensation. The device is specified over the industrial temperature range of -40°C to +85°C and is RoHS compliant. Typical applications include programmable voltage sources, digital gain and offset adjustment, and industrial process control. The low power consumption and small package make it suitable for portable instrumentation and battery-powered devices. The serial interface simplifies connection to microcontrollers and DSPs, reducing board space and pin count. When designing with the TLV5617A, ensure that the reference voltage is stable and bypassed with a 0.1 µF capacitor. The power supply should be decoupled with a 1 µF capacitor close to the VDD pin. The serial clock frequency should not exceed 20 MHz to maintain reliable communication.

询价 联系我们
TLV5627IPW - 8-Bit Quad DAC, Serial, TSSOP-16 | Texas Instruments
TLV5627IPW

TLV5627IPW - 8-Bit Quad DAC, Serial, TSSOP-16 | Texas Instruments

The Texas Instruments TLV5627IPW is a quad-channel, 8-bit voltage-output digital-to-analog converter (DAC) with a flexible 4-wire serial interface, packaged in a 16-pin TSSOP (PW) and operating from a 2.7V to 5.5V supply. Each of the four DAC channels features programmable settling time of either 2.5 µs (fast mode) or 8.5 µs (slow mode) and supports a 107 kSPS update rate, enabling both precision setpoint generation and waveform synthesis from a single chip. A digital-to-analog converter (DAC) is a mixed-signal integrated circuit that converts a digital codeword into a precision analog voltage or current; an 8-bit quad DAC like the TLV5627 delivers four such converters on one die with a shared digital interface, sitting within the broader hierarchy of converter ICs > data converters > signal chain > mixed-signal semiconductors. Unlike audio DACs that target continuous high-rate streaming, the TLV5627 is an industrial/multi-channel "set DAC" intended for bias voltages, trim references, programmable gain stages, and actuator control loops where four independent low-bandwidth analog outputs are required. Key features include a glueless serial interface compatible with TMS320 DSP, SPI, QSPI, and Microwire ports, an on-chip reference input buffer, hardware and software-controlled power-down modes that cut consumption to a few milliwatts, and guaranteed monotonic output over the full -40C to +85C industrial temperature range. The four outputs share a common DAC reference, but each channel can be powered down independently for further energy savings. Internally, the TLV5627 uses a resistor-string architecture with an output buffer amplifier per channel, providing low output impedance and the ability to drive 2 kohm loads directly. The dual-supply design separates the digital and analog domains (separate AVDD and DVDD pins), which is critical for noise-sensitive applications where digital switching transients must be isolated from the analog outputs. Typical applications include industrial process control (PLC analog outputs), programmable sensor excitation, digital offset and gain trimming, four-channel waveform or bias generation in test & measurement, motor and valve control loops, and audio tone/signal generation where mid-fidelity is acceptable. When designing with this device, ensure the AGND and DGND pins are joined at a single low-impedance point near the IC to prevent digital return currents from corrupting analog output accuracy. The reference input must be driven from a low-noise source, and the unused DAC outputs can be left open or tied to a defined voltage. Programming model: load data through the serial port (DIN, SCLK, FS) per the TI TLV5627 datasheet timing diagram. This page consolidates real-time distributor pricing, drop-in compatible alternatives, and practical PCB/design notes beyond what the manufacturer datasheet alone provides.

询价 联系我们
TLV571CDW - 8-Bit 1.25 MSPS ADC | Texas Instruments
TLV571CDW

TLV571CDW - 8-Bit 1.25 MSPS ADC | Texas Instruments

The Texas Instruments TLV571CDW is an 8-bit, single-channel, parallel-output analog-to-digital converter rated for 1.25 MSPS in the device family and 625 KSPS at a 3 V supply according to the manufacturer datasheet search result. It operates from 2.7 V to 5.5 V and accepts an analog input range from 0 V to AVDD. The device is packaged in a 16-pin SOIC package. An ADC is a data-acquisition IC that samples an analog voltage and converts it into a digital value. The TLV571 belongs to the ADC/DAC hierarchy and uses a successive-approximation, or SAR, conversion architecture. Its parallel interface provides eight digital output bits plus control and status signals, making it suitable for systems where a microcontroller, DSP, or other digital controller reads conversions without relying on a serial protocol. The verified manufacturer data identifies several useful features: 2.7 V to 5.5 V single-supply operation, 0 V to AVDD analog input range, differential and integral nonlinearity below ±0.5 LSB, and hardware configuration for DSP and microcontroller compatibility. The output can be binary or twos complement. Low-power operation is also emphasized, with 12 mW specified at 3 V and 35 mW at 5 V. Power management is handled through automatic power-down or software power-down, according to the manufacturer product description. Automatic power-down is listed at 1 mA maximum, while software power-down is listed at 10 maximum in the verified datasheet snippet. The internal oscillator and hardware-configurable interface make the converter useful for compact control, monitoring, and embedded acquisition systems. Typical uses include industrial sensor acquisition, battery-powered monitoring, portable instrumentation, embedded control, and DSP or microcontroller front ends. Designers should verify the exact timing, input impedance, reference requirements, acquisition-cycle behavior, and electrical limits against the complete manufacturer datasheet before finalizing a PCB. This page combines verified manufacturer and distributor information with engineering guidance for selecting, comparing, and integrating the TLV571CDW.

询价 联系我们
TLV571CPW - 8-Bit 1.25 MSPS ADC | Texas Instruments
TLV571CPW

TLV571CPW - 8-Bit 1.25 MSPS ADC | Texas Instruments

The Texas Instruments TLV571CPW is an 8-bit, single-channel, parallel-output analog-to-digital converter with a 1.25 MSPS sampling rate, 2.7 V to 5.5 V single-supply operation, and a 16-pin TSSOP package. It supports hardware-configurable or software power-down operation and provides binary or two's-complement output data for DSP, microcontroller, and other digital signal-processing systems. An ADC is a data-acquisition building block that converts an analog voltage into a numeric value for computation, measurement, control, or display. A single-channel 8-bit parallel ADC is useful when the design prioritizes low interface complexity and moderate resolution rather than high channel count or maximum conversion throughput. The TLV571 belongs to the ADC/DAC hierarchy and the broader data-converter semiconductor category. The TLV571CPW accepts an analog input range from 0 V to AVDD and supports supply voltages from 2.7 V to 5.5 V. Its differential and integral nonlinearity errors are each specified as less than plus or minus 0.5 LSB. The manufacturer lists an internal oscillator, a DSP- and microcontroller-compatible parallel interface, and automatic or software power-down features. These characteristics make it appropriate for compact embedded measurement systems where the host controller can sample parallel data directly. The device is designed for low-power operation, with listed power consumption of 12 mW at 3 V and 35 mW at 5 V. Automatic power-down is specified at a maximum of 1 mA, while software power-down is specified at a maximum of 10 mA. These values should be checked against the system power budget and control-signal requirements in the manufacturer datasheet, particularly when the converter is operated intermittently. Typical applications include industrial sensor acquisition, battery-powered instrumentation, consumer control boards, embedded measurement modules, DSP front ends, and microcontroller-based monitoring systems. The 8-bit resolution is most appropriate for coarse measurements, threshold sensing, digital control feedback, and system monitoring rather than precision laboratory measurement. The parallel bus also requires adequate board-routing space and host-controller I/O resources. A key design consideration is signal conditioning and reference integrity. The analog input must remain within the specified 0 V to AVDD range, and the host system should account for ADC input settling, source impedance, sampling timing, and digital-bus timing. This page combines verified manufacturer and distributor information with practical implementation guidance; unavailable pricing, pin-level details, and replacement data are explicitly marked rather than estimated.

询价 联系我们
TLV571IDW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments
TLV571IDW

TLV571IDW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments

The Texas Instruments TLV571IDW is an 8-bit, single-channel successive-approximation-register analog-to-digital converter with a maximum throughput of 1.25 MSPS, a 2.7 V to 5.5 V supply range, and a 24-pin SOIC (DW) package. The converter accepts an analog input from 0 V to AVDD and provides an 8-bit parallel output suitable for DSP and microcontroller interfaces. An ADC is a data-acquisition semiconductor that converts a continuous analog voltage into a numeric code for processing, measurement, or control. The TLV571 belongs to the SAR ADC family, whose internal comparator and successive approximation process provide a practical balance between conversion speed, resolution, cost, and power consumption. It is designed for low-power, single-ended measurement systems operating from 3 V or 5 V supplies. Key features include a maximum conversion rate of 1.25 MSPS, 625 kSPS operation at 3 V, differential and integral nonlinearity below ±0.5 LSB, and a wide analog input range of 0 V to AVDD. Binary and two's-complement output formats are supported. Hardware configuration, an internal oscillator, automatic power-down, and software power-down provide flexible control for portable and embedded systems. The device combines an 8-bit ADC with an 8-bit parallel interface and two on-chip control registers accessible through the bidirectional port. These registers support software conversion start and power-down control. The parallel architecture can reduce the serial-interface overhead required by many low-resolution converters, making the TLV571 useful where deterministic sampling and direct bus connection are more important than very high integration. Typical applications include industrial control, battery-powered instruments, process monitoring, consumer equipment, and embedded sensor acquisition. The single analog input and low operating power are particularly useful when a compact controller samples one slowly changing or periodically updated signal. The 5 V operating range also supports conventional industrial logic and DSP supply arrangements. Designers should account for the ADC input range, source impedance, reference behavior, acquisition timing, and digital-interface timing. The parallel bus requires sufficient driver and routing margin on the host processor, while the analog input should be driven so that the internal sampling network can settle before conversion begins. The manufacturer datasheet remains the controlling reference for pin functions, timing, and application-specific implementation details. This page consolidates verified manufacturer and distributor information, function-focused application guidance, parameter comparisons, and practical design considerations. It supplements the datasheet with purchasing context and structured engineering information while clearly identifying data that requires confirmation from the full manufacturer documentation.

询价 联系我们
TLV571IPW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments
TLV571IPW

TLV571IPW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments

The Texas Instruments TLV571IPW is an 8-bit, single-channel successive-approximation-register analog-to-digital converter with a conversion rate of 1.25 MSPS, supplied in a 24-pin TSSOP package. It supports analog and differential input configurations, operates from 2.7 V to 5.5 V, and provides a parallel digital output interface. Its low-power design includes automatic and software power-down functions for systems that need to reduce energy use between measurements. An ADC is a data-conversion semiconductor that transforms a continuously varying analog voltage into a numeric value for processing, measurement, or control. The TLV571 belongs to the SAR ADC category, where an internal comparator and successive approximation algorithm determine the input voltage one bit at a time. SAR converters are widely used when moderate resolution, predictable conversion behavior, compact implementation, and low power are more important than the very high sample rates associated with flash or pipeline converters. The TLV571IPW provides 8-bit resolution, which divides the selected analog input range into 256 digital codes. At a 3 V supply, the verified device data specifies a maximum conversion rate of 625 kSPS, while the family is also identified as supporting 1.25 MSPS operation. Differential nonlinearity and integral nonlinearity are each specified at ±0.5 LSB, providing concrete measures of transfer-error performance. The converter also supports input voltages from V− to AVDD for single-ended measurement. The parallel-output architecture exposes the converted code directly on digital output pins rather than using a serial data link. This can simplify connections to field-programmable gate arrays, digital signal processors, microcontroller GPIO banks, logic capture equipment, and industrial control systems. Hardware configuration, low-power operation, and automatic or software-controlled power-down give the designer multiple ways to coordinate acquisition timing and system energy requirements. Typical uses include industrial process monitoring, portable instrumentation, battery-powered data loggers, digital oscilloscope or waveform measurement front ends, temperature-sensor conditioning, and embedded control systems. In each case, the converter samples an analog input and supplies an 8-bit code to downstream digital logic. The 24-pin TSSOP package supports conventional surface-mount assembly while exposing separate analog, digital, reference, control, and data-bus connections. Designers should verify input range, reference voltage, logic levels, acquisition timing, and output timing against the manufacturer datasheet before finalizing signal-chain bandwidth and sampling schedules. The available verified results establish the 1.25 MSPS class, ±0.5 LSB nonlinearity figures, 2.7 V to 5.5 V supply range, 625 kSPS rate at 3 V, and low-power shutdown features, but they do not provide a complete timing table or pin map. Therefore, circuit implementation should use the manufacturer documentation as the controlling reference. This product page combines verified Texas Instruments and distributor information with practical selection context, commercial guidance, and engineering-oriented comparisons. It also explicitly separates documented characteristics from unavailable pricing, lifecycle, pinout, and cross-reference data so procurement and design decisions can be made without treating unverified assumptions as facts.

询价 联系我们