集成电路

DSPIC33FJ256GP510A-E/PT

DSPIC33FJ256GP510A-E/PT - 16-Bit DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP510A-E/PT is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS at 3.3 V, with 256 KB (256K x 8) of Flash program memory and 30 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. It combines a modified RISC CPU core with a DSP engine, making it a single-chip solution for motor control, digital power conversion, and embedded signal processing. A Digital Signal Controller (DSC) is a hybrid device that merges the real-time control capabilities of a microcontroller (MCU) with the math throughput of a digital signal processor (DSP). In the product taxonomy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes control-loop code and fixed-point DSP algorithms on the same core, eliminating the need for a separate DSP plus MCU pair. The dsPIC33F family is Microchip's 16-bit DSC line, positioned above 8-bit PIC MCUs and below 32-bit PIC32 devices. Key features of the DSPIC33FJ256GP510A-E/PT include 256 KB Flash, 30 KB SRAM, 40 MIPS operation at 3.0 V to 3.6 V, an extended temperature range of -40 C to +125 C, and a 100-pin TQFP footprint. The device integrates a 16-bit CPU with a 17x17-bit single-cycle multiplier, a barrel shifter, and a DMA engine, enabling deterministic execution of control algorithms. The 'A' suffix denotes the enhanced dsPIC33FJXXXGPX06A/X08A/X10A revision, which adds advanced analog peripherals and improved migration options across the 64-, 80-, and 100-pin family members. The E/PT ordering code indicates the extended (-40 C to +125 C) temperature grade in the 100-pin TQFP (12x12) package, and the part is listed as AEC-Q100 automotive qualified by distributor data. Typical applications include three-phase motor field-oriented control (FOC), digital power supplies and PFC stages, automotive sensor and actuator control, industrial servo drives, and solar micro-inverters. The 40 MIPS core and hardware multiplier allow current-loop execution well above 10 kHz while leaving CPU headroom for communication stacks. When designing with this device, note that the 100-pin TQFP (12x12) body differs from the 100-pin TQFP (14x14) used by the -E/PF variant; the two are not footprint-compatible despite sharing the same pin count. Verify the land pattern before layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP510A-I/PF

DSPIC33FJ256GP510A-I/PF - 16-bit 40MIPS DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP510A-I/PF is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance from 256 KB of Flash memory and up to 30 KB of SRAM, housed in a 100-pin TQFP (14x14 mm) package rated for industrial temperatures (-40C to +85C). A digital signal controller combines the control peripherals of a microcontroller with the computational throughput of a DSP core in a single device. In the power-management hierarchy, the dsPIC33F family sits between general-purpose MCUs (such as PIC18) and dedicated DSPs, offering single-cycle MAC, DSP multiply-divide, and hardware divide support while retaining MCU-style interrupt latency and peripheral sets. This hybrid architecture makes dsPIC33F DSCs a default choice for real-time control loops. Key features of the DSPIC33FJ256GP510A include a 16-bit modified Harvard architecture core running at up to 40 MIPS from a 3.0V to 3.6V supply, 256 KB (256K x 8) self-programming Flash, and an advanced analog portfolio including a high-speed 10-bit/12-bit ADC with multiple sample-and-hold circuits. The device also integrates UART, SPI, I2C, ECAN, and multiple 16-bit timers plus output-compare/input-capture channels for motor and power-conversion timing. The -I suffix denotes the industrial temperature range (-40C to +85C) and the Arrow listing confirms the dsPIC33FJ family carries AEC-Q100 qualification, supporting automotive deployments. In-circuit serial programming (ICSP) via any PGECx/PGEDx pair, supported by MPLAB X IDE, MPLAB XC-DSC compiler, and MPLAB Snap/ICD programmers, allows field firmware updates without pre-programming. Development can start on the Explorer 16/32 Development Board with a dsPIC PIM. Typical applications include switch-mode power supplies and digital power conversion, sensorless BLDC/PMSM motor control, automotive body and convenience modules, and industrial sensing nodes that fuse ADC sampling with DSP filtering routines such as FIR/IIR. Design consideration: the core runs at 3.3V only - level-shift any 5V digital interfaces, and connect all VDD/VSS pairs as required for ICSP reliability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP510A-I/PT

DSPIC33FJ256GP510A-I/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP510A-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS at 3.3V, with 256KB Flash and 30KB SRAM, housed in a 100-pin TQFP (12x12 mm) package. A digital signal controller combines the computational power of a DSP with the peripheral integration and ease of use of a microcontroller, forming the top tier of the general-purpose (GP) branch of the dsPIC33F family within the broader power-management-by-periphery hierarchy of 16-bit embedded processors. DSCs are the standard choice where both control-loop code and real-time math (filters, transforms, PID) must run on one chip. Key features include a 16-bit dsPIC RISC core at up to 40 MIPS, two on-chip ADC modules configurable as 10-bit/1.1 Msps with four sample-and-hold circuits or 12-bit/500 ksps with one sample-and-hold, and up to 32 analog inputs on 100-pin devices with flexible, independent ADC trigger sources. The dsPIC33FJ256GP510A utilizes Microchip's modified Harvard architecture with DSP engine (40-bit accumulator, 17-bit x 17-bit single-cycle MAC), flexible interrupt structure, and multiple PGECx/PGEDx pin pairs for In-Circuit Serial Programming (ICSP) and debugging via MPLAB tools such as MPLAB Snap and the MPLAB XC-DSC compiler. The A-grade silicon is the current production revision, backward-compatible in code for legacy dsPIC33FJ designs after recompilation. Typical applications include industrial motor control and power conversion, automotive and industrial sensing nodes (Arrow lists the family as AEC-Q100-qualified), audio processing, and general-purpose embedded control in medical and consumer products. Design consideration: pair every VDD/VSS pair with local decoupling and confirm PGECx/PGEDx pairs are routed as matched pairs for programming access. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP510T-I/PT

DSPIC33FJ256GP510T-I/PT - 16-bit 40 MIPS DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP510T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33FJ256GP510 General Purpose family, delivering 40 MIPS performance, 256KB (256K x 8) of FLASH program memory, 16KB of RAM, and a 3.3V supply, housed in a 100-pin TQFP (12x12 mm) surface-mount package. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and control peripherals of a microcontroller. DSCs sit between general-purpose MCUs and dedicated DSPs in the processing hierarchy, making them the preferred choice when an application needs both fast math (multiply-accumulate, division support) and rich real-time control peripherals on a single chip. Key features include the dsPIC33F 16-bit core with DSP engine at up to 40 MIPS, 256KB self-programming FLASH, 16KB RAM, an internal on-chip regulator supplying the 1.8V core (external low-ESR capacitor required on VCAP), industrial temperature rating of -40C to +85C, and in-circuit serial programming (ICSP) and debugging support via MPLAB tools such as the MPLAB SNAP. The dsPIC33FJXXXGPX06/X08/X10 family shares a common peripheral set: multiple UART, SPI, and I2C modules, motor-control and general-purpose PWM outputs, a high-speed 12-bit ADC, input capture/output compare channels, and flexible interrupt architecture. Per the Microchip family data sheet (document 70286C), the family is pin compatible with the PIC24H family and shares a very high degree of compatibility with the dsPIC30F family, enabling easy migration between families as application requirements evolve. Typical applications include industrial automation and control, motor drives and power conversion, digital power supplies, sensor signal conditioning and digital filtering, and embedded systems requiring deterministic real-time performance with DSP-class arithmetic. Design consideration: the on-chip regulator requires a low-ESR capacitor (such as tantalum) on the VCAP pin to maintain core voltage stability; omitting or undersizing this capacitor is a common cause of startup instability. This page synthesizes distributor pricing, drop-in alternatives, design notes, and comparison data not found in the manufacturer data sheet. Pricing shown is as of 2026-09-27.

询价联系我们

DSPIC33FJ256GP710-I/PT

DSPIC33FJ256GP710-I/PT - 16-bit DSC 40 MIPS 256KB Flash | Microchip

The Microchip DSPIC33FJ256GP710-I/PT is a high-performance 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS at 3.0-3.6V, with 256KB of Flash memory and an industrial-grade (-40C to +85C) 100-pin TQFP (PT) package. It belongs to the dsPIC33F General Purpose family, which combines MCU control peripherals with DSP-engine math capability in a single 3.3V device. A Digital Signal Controller is a hybrid device class sitting between microcontrollers and digital signal processors: it retains the deterministic interrupt structure, peripherals and C-programmability of an MCU while adding a DSP engine, hardware multiply-accumulate (MAC) unit and dual operand fetch for filtering, transforms and control-loop mathematics. DSCs occupy the power-management and embedded-control hierarchy between simple PIC16-class MCUs and full DSPs. Key features include the 16-bit modified Harvard architecture with a 40-MIPS maximum core clock, 256KB (85.5K instructions x 24-bit) self-programmable Flash, 30KB of SRAM, and seamless migration options to PIC24F/PIC24H MCUs and dsPIC30F DSCs in similar packages. The peripheral set covers 10-bit/12-bit ADC capability, multiple UART, SPI and I2C ports, output compare and input capture channels, and ECAN support, making the device suitable for both analog-front-end and communication-intensive designs. Technically, the dsPIC33FJ core adds single-cycle MAC, dual data reads, modulo and bit-reversed addressing, and a hardware divide, enabling real-time FIR/IIR filtering and FFT algorithms without external acceleration. Operating range is up to 40 MIPS at 3.0-3.6V, per the dsPIC33FJXXXGPX06/X08/X10 data sheet (document 70286C). In-circuit serial programming (ICSP) uses any PGECx/PGEDx pair, simplifying production programming and debug through standard MPLAB tools. Typical applications include industrial control and automation nodes, digital audio and sensor-signal processing, power-supply and instrumentation systems, and communication gateways that pair ADC front-end work with CAN/UART traffic. The 100-pin TQFP offers generous general-purpose I/O for dense board designs. Design consideration: use any PGEC/PGED pair consistently for programming - if PGEC2 carries ICSPCLK, PGED2 must carry ICSPDAT. Budget 3.0-3.6V supply rails and decouple each VDD pin for full 40-MIPS operation. This page synthesizes distributor pricing, same-footprint alternatives, and drop-in replacement guidance not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710A-E/PF

DSPIC33FJ256GP710A-E/PF - 16-bit DSC 40 MIPS 256 KB Flash | Microchip

The Microchip DSPIC33FJ256GP710A-E/PF is a 16-bit Digital Signal Controller delivering 40 MIPS core performance with 256 KB of self-programmable Flash and 30 KB of SRAM, housed in a 100-pin 14x14 mm TQFP (PF) package and qualified for the -40C to +125C extended industrial temperature range. A Digital Signal Controller (DSC) combines the deterministic math throughput of a digital signal processor with the rich peripheral integration of a microcontroller, and it sits in the embedded computing hierarchy between general-purpose MCUs and standalone DSPs. Within Microchip's portfolio the dsPIC33F family specifically targets real-time closed-loop control applications, sitting above the PIC24F/PIC24H MCU families and below the dsPIC33E and dsPIC33C high-performance successors. The GP (General Purpose) sub-family inside dsPIC33F is the all-rounder line optimized for general embedded signal processing and motor / power control rather than audio codec pipelines. Key features of the dsPIC33FJ256GP710A include a 16-bit dsPIC33F modified Harvard core with single-cycle MAC and DSP engine instructions, 16-channel 10-bit / 12-bit ADC, multiple PWM generators, two analog comparators, two I2C, two SPI, two UART, an ECAN module, and a parallel master port. A-suffix silicon is the current die revision of the original dsPIC33FJ256GP710, with corrected errata and full manufacturer support through MPLAB X IDE and the MPLAB XC-DSC compiler. Architecturally, the 40 MIPS core pairs a 16-bit ALU with a dedicated DSP engine supporting single-cycle MAC and dual data fetch, enabling real-time control algorithms such as field-oriented motor control, digital filters, and power conversion feedback loops without external co-processors. The GP peripheral set prioritizes general-purpose timers and PWM over the dedicated motor-control PWM of the MC sub-family, and the A revision integrates errata fixes versus the original die. Typical applications include industrial motor drives (PMSM, BLDC, ACIM), digital power supplies (PFC, LLC, full-bridge converters), solar micro-inverters, and automotive body and convenience ECUs where the H-grade sibling enables AEC-Q100 qualification. The 100-pin TQFP package exposes most of the peripheral I/O for high-pinout designs. Design consideration: the device operates from a single 3.0 V to 3.6 V supply, so plan level shifting for 5 V peripherals and respect the 40 MIPS core of the dsPIC33F when computing CPU headroom. Always assign PGECx / PGEDx as paired pins for ICSP and route the analog AVdd / AVss rails with separate decoupling from Vdd / Vss to preserve ADC accuracy. This page synthesizes distributor pricing, drop-in same-package alternatives, extended-temperature substitution guidance, and practical design notes that complement the manufacturer datasheet's full pin-by-pin specification.

询价联系我们

DSPIC33FJ256GP710A-E/PT

DSPIC33FJ256GP710A-E/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP710A-E/PT is a 16-bit general purpose Digital Signal Controller (DSC) delivering up to 40 MIPS from a 256 KB Flash program memory and 30 KB SRAM, supplied in a 100-pin TQFP (12x12 mm) package with extended industrial temperature rating (-40C to +125C). A Digital Signal Controller combines the computational architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, the dsPIC33F family sits between general-purpose PIC24 microcontrollers and dedicated DSPs, offering DSP engine instructions (MAC, DSP multiply, barrel shifter) alongside standard MCU peripherals. Key features of the DSPIC33FJ256GP710A include 85 general-purpose I/O pins, two 3-wire SPI ports, two I2C interfaces, two UART modules, and advanced analog integration suited to speech and audio processing, as highlighted by Future Electronics. The A variant of the dsPIC33FJ256GP710 family adds codec interfaces, making it well-suited for audio and speech applications. The device is qualified to AEC-Q100 for automotive use (denoted by the /E temperature grade and automotive listing in distributor data) and operates from a single 3.0 V to 3.6 V supply. The modified Harvard architecture with a 16-bit data path and DSP instruction support enables single-cycle MAC operations for filtering and control loops. Program flash is rated for in-system self-programming, and ICSP/ICD programming is supported through paired PGECx/PGEDx pins. Typical applications include automotive control modules, speech and audio processing systems, digital power conversion, sensor signal conditioning, and industrial control requiring DSP-class math with MCU-class integration. Development is supported by the Explorer 16/32 Development Board and the MPLAB XC-DSC C/C++ compiler. Design consideration: supply voltage must remain within 3.0 V to 3.6 V, and multiple PGECx/PGEDx pin pairs must be used as matched pairs during programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710A-H/PF

DSPIC33FJ256GP710A-H/PF - 16-bit DSC, 40 MIPS, 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP710A-H/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F General Purpose family, delivering up to 40 MIPS performance with 256 KB of Flash program memory and 30 KB of SRAM, housed in a 100-pin TQFP (PF) package. The AEC-Q100 qualified IC runs from 3.0 V to 3.6 V and offers 85 general-purpose I/O pins with extensive digital and analog peripherals. A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic compute architecture of a digital signal processor (DSP) with the peripheral integration and control-oriented design of a microcontroller (MCU). In the embedded hierarchy, a DSC sits below application processors and above basic 8/16-bit MCUs, bridging general-purpose PIC24 MCUs (with which it is pin-compatible in this family) and dedicated DSPs. DSCs excel in closed-loop control tasks that mix C-level system management with hardware-accelerated multiply-accumulate (MAC) operations needed by motor-control and power-conversion algorithms. Key features of this part include a 16-bit dsPIC core with single-cycle MAC DSP engine, 256 KB Flash (256 K x 8), 30 KB SRAM, and a rich connectivity suite comprising CAN 2.0B, I2C, SPI, UART/USART, IrDA, and LINbus. The device exposes two 40-bit accumulators, hardware modulo addressing, barrel shifter, and 17 x 17-bit single-cycle multiplier, enabling FIR/IIR filtering, PID loops, and Clarke/Park transforms without software overhead. Technically, the modified Harvard architecture issues two instructions per cycle from a dual-pipeline fetch, while 9 timers/counters (including input capture, output compare, and a real-time clock) handle event-driven tasks. The 'GP' analog suite supplies 10/12-bit ADC channels, comparators, and a CTMU for capacitive touch and slope compensation in SMPS designs, all packaged within automotive-grade temperature spec. Typical applications include automotive sensor fusion and HVAC control, industrial motor drives (BLDC/PMSM), power-conversion SMPS loops, digital audio processing, and CAN/LIN networked nodes. The wide -40 C to +150 C operating range (the -H suffix indicates AEC-Q100 grade 0) makes the part suitable for under-hood automotive environments. Design consideration: place a 10 uF bulk + 0.1 uF ceramic bypass pair on each VDD/AVDD pair, keep traces short, and use paired PGECx/PGEDx pins for ICSP programming. Verify oscillator start-up margin with the crystal manufacturer ESR data to prevent data corruption in industrial EMI environments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710A-H/PT

DSPIC33FJ256GP710A-H/PT - 16-bit 40 MIPs DSC 256KB | Microchip

The Microchip Technology DSPIC33FJ256GP710A-H/PT is a 16-bit dsPIC33F general purpose Digital Signal Controller (DSC) delivering 40 MIPs performance with 256KB (256K x 8) FLASH program memory, 30KB of RAM, and a 3.3V supply, housed in a 100-pin TQFP (12x12 mm) package. A Digital Signal Controller combines the control peripherals of a microcontroller with the multiply-accumulate engine of a DSP. Within the power-management hierarchy, the dsPIC33F family sits between standard MCUs and dedicated DSPs: it is a 16-bit microcontroller (PIC24 architecture) with DSP instructions, making it a single-chip solution for motor control and digital power conversion. Key features include a 16-bit RISC dsPIC33F core running at 40 MIPs, 256KB self-programmable FLASH with ECC, 30KB SRAM, and rich connectivity: CANbus, I2C, IrDA, LINbus, SPI, and UART/USART. Analog peripherals and multiple timers plus PWM modules enable closed-loop digital control without external DSP support. Technical depth: the dsPIC33F core executes most instructions in one cycle and includes a 17-bit x 17-bit single-cycle hardware multiplier, dual 40-bit accumulators, and DSP addressing modes. Seamless migration paths exist to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar packages. The -H/PT variant is specified over an automotive-oriented extended temperature range with 3.3V operation. Typical applications include automotive electronic control units, digital power supplies, industrial motor drives, sensor fusion nodes, and communication gateways using the on-chip CAN module. Design consideration: only matched PGECx/PGEDx pin pairs may be used for ICSP programming (e.g., PGEC2 with PGED2), and multiple voltage-rail domains require attention during in-circuit debugging. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in alternatives, design notes, and AEO-optimized Q&A in one structured reference.

询价联系我们

DSPIC33FJ256GP710A-I/PF

DSPIC33FJ256GP710A-I/PF - 16-bit 40 MIPS DSC 256KB Flash TQFP-100 | Microchip

The Microchip Technology DSPIC33FJ256GP710A-I/PF is a 16-bit general-purpose Digital Signal Controller (DSC) delivering up to 40 MIPS from its dsPIC33F core, with 256 KB of Flash program memory and 30 KB of SRAM, housed in a 100-pin TQFP (PF, 14x14 mm) surface-mount package with an industrial -40C to +85C operating range. A Digital Signal Controller combines the deterministic interrupt architecture and peripheral set of a microcontroller with the multiply-accumulate (MAC) DSP engine of a digital signal processor. In the embedded-systems hierarchy, the DSC sits between a general-purpose MCU (such as a PIC18) and a dedicated DSP, making it a natural fit for motor control loops, digital power supplies, and sensor-fusion applications that need both control flow and real-time math in a single chip. Key features include the 16-bit modified Harvard core with two 40-bit accumulators and single-cycle MAC, 256 KB (256K x 8) self-programmable Flash with ECC-style write protection, up to 85 general-purpose I/O pins, and rich connectivity: CAN 2.0B, two UART modules, two I2C ports, two SPI ports, and a DCI codec interface. The analog subsystem provides a 10-bit, 1.1 Msps ADC with up to 32 input channels plus multiple analog comparators. Architecturally, the 'A' revision of the dsPIC33FJ256GP710 family refines the original die for improved manufacturing and provides seamless migration paths to PIC24H MCUs and other dsPIC33F devices in the same footprint. Peripherals are clocked from an on-chip PLL fed by an external crystal or the internal 7.37 MHz FRC oscillator with a fail-safe clock monitor and brown-out reset for safety-critical designs. Typical applications include BLDC and PMSM motor control, digital power conversion (LLC, PFC), industrial sensing, automotive body controllers (when using the -H grade), and embedded control panels requiring CAN bus networking. Design consideration: the 100-pin TQFP requires careful decoupling of all VDD/VSS pairs and a solid ground plane; Flash self-programming during ICSP requires VDD within 3.0 V to 3.6 V to stay in spec. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in same-footprint alternatives across the dsPIC33FJ family, and practical design notes for supply-chain-resilient BOM planning.

询价联系我们

DSPIC33FJ256GP710A-I/PT

DSPIC33FJ256GP710A-I/PT - 16-bit 40MIPS 256KB DSC | Microchip

The Microchip Technology DSPIC33FJ256GP710A-I/PT is a 16-bit general purpose digital signal controller (DSC) delivering up to 40 MIPS from a 256 KB flash memory and 30 KB SRAM, housed in a 100-pin TQFP (12x12 mm) package rated for -40C to +85C industrial operation. A digital signal controller combines the computing architecture of a microcontroller with the DSP engine of a digital signal processor. Within the power management hierarchy of embedded systems, a DSC such as the dsPIC33F family sits between general-purpose MCUs and dedicated DSPs: it executes digital filter algorithms and high-speed precision digital control loops with single-cycle MAC and 40-bit accumulators, while retaining the peripherals, interrupts, and flash self-programming of a modern MCU. Microchip's dsPIC33FJXXXGPX06A/X08A/X10A family is explicitly designed for applications that need to perform under pressure. Key features include 256 KB of on-chip flash with ECC-style self-programming support, 30 KB of SRAM, up to 53 general-purpose I/O pins, and rich communication peripherals including CAN, I2C, SPI, and UART. The GP (general purpose) variant adds a high-speed 10/12-bit ADC and the DCI (Data Converter Interface) for codec connection, making it a strong fit for audio and precision sensing signal chains. Architecturally, the dsPIC33F core uses a modified Harvard pipeline with hardware loop support, 16 x 16 working register arrays, DSP multiply-accumulate, and modulo/bit-reversed addressing for FFTs. The A-suffix die is Microchip's enhanced revision of the original dsPIC33FJ256GP710 with improved analog and timing specifications. Typical applications include motor control front-ends, digital power supplies, audio processing and codec interfaces, industrial sensing, and general embedded control requiring DSP-class math. Migration within the dsPIC33F family is seamless, and the Explorer 16/32 Development Board supports this device through a 100-pin PIM for rapid prototyping. Design consideration: the device is a 3.3 V-supply part, so level shifting is required for 5 V logic, and ICSP programming must use matched PGECx/PGEDx pin pairs per the programming specification. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in a single manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710AT-I/PF

DSPIC33FJ256GP710AT-I/PF - 16-Bit 40MIPS 256KB Flash DSC | Microchip

The Microchip Technology DSPIC33FJ256GP710AT-I/PF is a high-performance 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from its dsPIC33F core, with 256KB of Flash program memory, housed in a 100-pin TQFP (14x14 mm, PF) package rated for industrial temperatures (-40C to +85C) at 3.3V operation. A Digital Signal Controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice when an application needs both real-time control loops and math-intensive signal processing in a single chip. The dsPIC33F family belongs to Microchip's 16-bit controller portfolio and offers seamless migration to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar packages. Key features of this device include a 16-bit modified Harvard architecture with DSP engine supporting single-cycle MAC and 40-bit accumulators, 256KB (256K x 8) of self-programmable Flash and substantial SRAM for buffering, and operation up to 40 MIPS at 3.3V. The AT suffix denotes the extended automotive/industrial temperature grade, and the I suffix confirms industrial operating range. Technical depth: the device integrates multiple timers, input capture/output compare channels, motor-control PWM, multi-channel 10/12-bit ADCs, UART, SPI and I2C interfaces, plus dual PGECx/PGEDx pairs for in-circuit serial programming (ICSP). Note that programming pairs must be used as matched sets - if PGEC2 carries ICSPCLK, ICSPDAT must connect to PGED2, as documented in Microchip programming guides. Typical applications include motor control (BLDC/PMSM FOC), digital power supplies and inverters, audio and speech processing, sensor-fusion and industrial automation nodes where deterministic 16-bit control plus DSP math is required. Design consideration: budget power and clock architecture carefully - a 40 MHz-class core needs clean 3.3V decoupling at every VDD pin and careful crystal/PLL layout for stable operation. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710AT-I/PT

DSPIC33FJ256GP710AT-I/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256GP710AT-I/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC33FJ256GP710A family delivering up to 40 MIPS performance, 256KB of Flash program memory, and 30KB of RAM, housed in a 100-pin TQFP (12x12 mm) package rated for industrial temperatures from -40C to +85C at 3.3V operation. A Digital Signal Controller combines the compute architecture of a microcontroller with DSP capabilities such as single-cycle MAC multiply-accumulate and hardware divide support. Within the power-management hierarchy of embedded processors, the dsPIC33F sits between general-purpose 16-bit MCUs (like the PIC24H, with which it is pin compatible) and dedicated DSPs, making it a middle path for real-time control plus signal processing. The dsPIC33F family shares a high degree of compatibility with the dsPIC30F family, allowing migration between device generations as system requirements evolve. Key features include the 16-bit dsPIC core clocked at 40 MHz for 40 MIPS throughput, rich connectivity with CAN, I2C, SPI, and UART modules, 53 general-purpose I/O pins, and In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pin pairs. The device is supported by the MPLAB XC-DSC C/C++ optimizing compiler and MPLAB Snap debugger. Architecture highlights: the modified Harvard pipeline executes most instructions in a single cycle, while hardware DSP multiply-accumulate instructions accelerate filtering, FFT, and control-loop math without software libraries. Dual-source Flash variants (the AT suffix denotes the A-version silicon with tape-and-reel ordering) simplify supply continuity. Typical applications include digital power supplies, motor control and PFC stages, industrial automation nodes with CAN networking, and audio or sensor signal-processing pipelines where 40 MIPS and on-chip DSP math remove the need for a second processor. Design consideration: pair multiple decoupling capacitors on the 3.3V rails and route PGEC/PGED pairs carefully for debug access; only paired PGECx/PGEDx pins may be used together for ICSP. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256GP710T-I/PT

DSPIC33FJ256GP710T-I/PT - 16-bit 40 MIPS DSC 256KB Flash | Microchip

The Microchip DSPIC33FJ256GP710T-I/PT is a 16-bit general-purpose Digital Signal Controller (DSC) delivering 40 MIPS at 40 MHz, with 256 KB of Flash program memory and 30 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. It operates from a 3.0 V to 3.6 V supply and over an industrial temperature range of -40C to +85C. A Digital Signal Controller combines the compute architecture of a microcontroller with the math throughput of a DSP. Within the power-management hierarchy of embedded semiconductors, the dsPIC33F family sits between general-purpose MCUs (such as PIC24) and dedicated DSPs, integrating a DSP engine with multiply-accumulate (MAC) instructions, high-speed ADC, PWM, and comparators on a single chip. Key features include the 16-bit modified Harvard architecture with 16 W x 16-bit multiply and 32/16-bit divide support, 85 general-purpose I/O, 35 I/O ports per digchips listing data, up to four high-speed comparators with direct ADC connection, and seamless migration options to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar packages per the Microchip product page. Flash program memory is 256 KB (256K x 8), SRAM is 30 KB (30720 bytes per Mouser listing), and the device is supplied in Tape and Reel packaging (suffix T). Technically, the dsPIC33F core runs its instruction and clock system at 40 MHz for 40 MIPS throughput, supported by an on-chip oscillator system and a rich interrupt architecture suited to deterministic real-time control loops. Peripherals typically include UART, SPI, I2C, ECAN, and a high-speed 10/12-bit ADC, enabling closed-loop control with sampling and computation in a single cycle-accurate pipeline. Typical applications include digital power supplies, motor control inverters, sensor signal conditioning and industrial automation nodes, all of which benefit from the combination of DSP math throughput and MCU peripheral integration. The general-purpose (GP) variant is preferred where broad analog and communication peripherals are needed rather than the motor-control (MC) focused PWM sets. A key design consideration: the device supports multiple PGECx/PGEDx pin pairs for ICSP programming, but each pair must be used as a matched pair - if PGEC2 carries ICSPCLK, ICSPDAT must connect to PGED2, as documented by Microchip development resources. This page synthesizes distributor listings, drop-in family alternatives, and design guidance not consolidated in the manufacturer datasheet alone. Prices shown are estimated as of 2026-09-27 and should be confirmed at checkout.

询价联系我们

DSPIC33FJ256MC510-I/PT

DSPIC33FJ256MC510-I/PT - 16-Bit DSC 40 MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC510-I/PT is a 16-bit dsPIC33F digital signal controller (DSC) delivering 40 MIPS performance with 256KB (256K x 8) of FLASH program memory and 30KB of RAM, housed in a 100-pin TQFP (12x12 mm) package rated for -40C to +85C operation. A digital signal controller combines the deterministic control of a microcontroller with the mathematical throughput of a DSP on a single die. In the semiconductor hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it executes microcontroller-style C code and interrupt handling while also providing hardware MAC, divide, and barrel-shift instructions for control-loop mathematics. The dsPIC33F family belongs to Microchip's broader 16-bit architecture, with seamless migration paths to PIC24 MCUs and dsPIC30F DSCs in similar packages. Key features include the modified Harvard 16-bit core with DSP engine, single-cycle MAC, 40 MIPS at 3.3V operation, motor-control specific peripherals (advanced PWM with dead-time insertion and ADC with simultaneous sampling), plus UART, SPI, I2C, ECAN, and multiple 16-bit timers. Industrial temperature qualification (-40C to +85C, suffix -I) suits factory-floor designs. Architecturally, the dsPIC33FJ256MC510 pairs its 256KB self-programming FLASH with 30KB SRAM and a rich interrupt vector table. The MC (Motor Control) variant adds complementary-output PWM channels and fast ADC conversion rates essential for field-oriented motor control and digital power conversion. Typical applications include brushless DC and PMSM motor drives, digital power supplies (PFC, LLC), industrial automation nodes, and sensor signal processing requiring DSP-grade math. Design consideration: all VDD/VSS pairs must be connected, and PGECx/PGEDx pairs must be used as matched pairs for In-Circuit Serial Programming. This page synthesizes drop-in alternatives, cross-reference options, pricing context, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256MC510A-E/PT

DSPIC33FJ256MC510A-E/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC510A-E/PT is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS performance with 256 KB of Flash memory, integrated CAN 2.0B, and extended temperature operation from -40C to +125C in a 100-pin TQFP (12x12 mm) surface-mount package. A Digital Signal Controller combines the compute architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, the dsPIC33F family sits alongside 16-bit MCUs such as the PIC24, offering single-cycle MAC, DSP multiply/divide, and barrel shifter instructions for real-time control loops. The dsPIC33FJ256MC510A belongs to the Motor Control (MC) subfamily, purpose-built for electromagnetic and power conversion workloads. Key features include 256 KB of self-programmable Flash, 40 MIPS at 3.3 V, dual CAN 2.0B modules, motor-control PWM peripherals, a 10-bit high-speed ADC, and AEC-Q100 qualification for automotive environments. The -E suffix denotes extended industrial/automotive temperature grading. The dsPIC33F core uses a modified Harvard architecture with a 16-bit data path and pipelined instruction execution, enabling deterministic interrupt latency essential for field-oriented control (FOC) and sensorless BLDC algorithms. Flash self-programming supports field firmware updates, and the peripheral ecosystem includes UART, SPI, and I2C for connectivity. Typical applications include brushless DC (BLDC) motor drives, single- and 3-phase induction motor control, switched reluctance motor systems, UPS and solar inverters, and automotive body electronics with CAN networking. The integrated motor-control PWM and fast ADC make it a strong fit for digital power supplies. Designers should budget decoupling on every VDD/VSS pair, plan the 100-pin footprint for PWM-to-gate-driver routing, and respect the 3.6 V absolute maximum on digital pins. This page synthesizes distributor pricing, drop-in alternatives, design notes, and FAQ content not found in a single manufacturer datasheet.

询价联系我们

DSPIC33FJ256MC510AT-I/PF

DSPIC33FJ256MC510AT-I/PF - 16-bit 40 MIPS DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC510AT-I/PF is a 16-bit digital signal controller (DSC) delivering up to 40 MIPS performance with 256KB of Flash program memory, 16KB of RAM, and a 3V to 3.6V supply range, housed in a 100-lead TQFP (14x14 mm, 0.5 mm pitch) package. A digital signal controller combines the computational architecture of a microcontroller (MCU) with the numeric acceleration of a digital signal processor (DSP). In the product hierarchy, the dsPIC33F family sits between general-purpose 16-bit PIC24 MCUs and dedicated DSPs, offering a RISC core modified with DSP instructions, dual operand fetch, and a hardware multiply-accumulate unit. This makes DSCs ideal for closed-loop control loops that need both deterministic real-time behavior and math-intensive algorithms. Key features of the DSPIC33FJ256MC510AT-I/PF include the 16-bit dsPIC33F RISC core rated at 40 MIPS, 256KB (256K x 8) of self-programmable Flash, 16KB of SRAM, 8 DMA channels, 9 timers, and 4 serial I/O modules. The MC (Motor Control) variant integrates dedicated peripherals for three-phase inverter drive, making it a strong fit for field-oriented control firmware. Architecturally, the CMOS device employs a 3-stage pipeline with separate program and data buses (Harvard architecture), single-cycle MAC operations, and support for DSP multiply, divide, and bit-manipulation instructions. The core clock reaches 40 MHz, corresponding to the 40 MIPS rating. Typical applications include brushless DC (BLDC) motor drive, single- and three-phase induction motor control, switched reluctance motor systems, uninterruptible power supplies (UPS), and digital power conversion - use cases Microchip explicitly targets with the dsPIC33F MC family. Digital filtering and sensor fusion tasks in industrial automation also benefit from the on-chip DSP engine. Design consideration: the 3V-3.6V supply window requires a clean LDO or buck-derived rail; leave adequate decoupling on all VDD/VDDCORE pairs, and verify Flash programming voltage requirements during in-circuit programming with tools like PICkit or ICD headers. This page synthesizes distributor pricing, drop-in alternatives, pin-package options, and motor-control design notes not consolidated in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256MC510T-I/PF

DSPIC33FJ256MC510T-I/PF - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC510T-I/PF is a 16-bit digital signal controller (DSC) from the dsPIC33F Motor Control family, delivering 40 MIPS performance with 256KB of FLASH program memory and 16KB of RAM, housed in a 100-pin TQFP (14x14 mm) lead-free plastic package. A digital signal controller combines the computational power of a digital signal processor (DSP) with the peripheral integration and control flexibility of a microcontroller (MCU). In the system hierarchy, the dsPIC33F sits between general-purpose MCUs and dedicated DSPs: it executes microcontroller-style deterministic interrupt-driven control loops while providing hardware DSP multiply-accumulate instructions for filtering and transformation tasks. This makes DSCs the preferred choice for closed-loop power conversion and motor drive systems. Key features of the DSPIC33FJ256MC510T-I/PF include a 16-bit dsPIC core running at up to 40 MIPS from a 3.0V to 3.6V supply, 35 I/O pins, and motor-control-centric peripherals: high-speed PWM modules, up to four high-speed comparators with direct connections, and a high-speed ADC for simultaneous multi-channel current sampling. Connectivity covers CANbus, I2C, IrDA, LINbus, SPI, and UART/USART, enabling integration into automotive-style and industrial networks. Architecturally, the dsPIC33F core pairs a 16-bit modified Harvard pipeline with two 40-bit accumulators and hardware DSP instructions, allowing single-cycle MAC operations at the full 40 MIPS clock rate. The flash-based program memory supports in-circuit self-programming, and the device offers seamless migration paths to PIC24 MCUs and dsPIC30F DSCs in similar packages, protecting software and hardware investment. Typical applications include brushless DC motor drives, single- and 3-phase induction motor control, switched reluctance motor systems, and digital power supplies such as LLC and PFC stages. The high-speed PWM, ADC, and comparator set maps directly onto sensorless FOC control loops. Design consideration: operate the device within its 3.0V to 3.6V supply window and budget decoupling per supply pin pair; the 100-pin TQFP with 0.5 mm pitch requires careful PCB land-pattern compliance for reliable assembly. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet, providing added selection value beyond the raw specification table.

询价联系我们

DSPIC33FJ256MC710-I/PF

DSPIC33FJ256MC710-I/PF - 40MIPS 16-bit DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC710-I/PF is a 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from its dsPIC33F core, with 256KB of Flash program memory and 8192 words (30KB) of RAM, housed in a 100-pin TQFP (14x14 mm, PF) surface-mount package rated for the industrial temperature range of -40C to +85C. A Digital Signal Controller combines the compute structure of a microcontroller with the mathematical acceleration of a digital signal processor. In the power-management IC hierarchy, the dsPIC33F sits between general-purpose MCUs (such as the PIC24H family, with which it is pin compatible) and dedicated DSPs, offering a hardware multiply-accumulate (MAC) unit, barrel shifter, and fixed-point DSP engine within an MCU-class peripheral set. This makes it a natural fit for embedded control loops that also need real-time signal math. Key features of the DSPIC33FJ256MC710-I/PF include its 40 MIPS performance at 3.3V operation, 256KB of self-programmable Flash, and a motor-control-oriented peripheral suite with complementary PWM outputs and quadrature encoder interface support, tailored for digital power conversion and motion control. According to Microchip product documentation, the family offers seamless migration options to and from PIC24 MCUs and dsPIC30F DSCs in similar packages. Technically, the dsPIC33F core executes C compiler-friendly 16-bit instructions while the DSP engine performs single-cycle MAC operations; boundary-scan support and in-circuit serial programming (ICSP) via PGECx/PGEDx pin pairs simplify debug and production programming. Microchip notes that all VDD and VSS pins must be connected and PGECx/PGEDx must be used as matched pairs for reliable programming. Typical applications include brushless DC motor drives, single- and three-phase induction motor control, switched reluctance motors, digital power supplies, and sensorless servo positioning systems where deterministic 40 MIPS execution and fast interrupt response matter. A key design consideration: the DS (not recommended for new design) status of the base dsPIC33FJ256MC710 means new designs should target the pin-compatible dsPIC33FJ256MC710A variant, which shares the same TQFP-100 footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价联系我们

DSPIC33FJ256MC710-I/PT

DSPIC33FJ256MC710-I/PT - 40 MIPS 16-bit DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC710-I/PT is a high-performance 16-bit Digital Signal Controller (DSC) delivering 40 MIPS core throughput with 256 KB of self-programmable Flash program memory, housed in a 100-pin TQFP (12x12 mm) package rated for the industrial -40C to +85C temperature range. A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response and peripheral integration of a microcontroller (MCU) with the single-cycle multiply-accumulate (MAC) throughput of a digital signal processor (DSP). In the embedded-control hierarchy, a DSC sits between general-purpose 16-bit MCUs (such as the PIC24 family) and standalone DSPs, making it the de-facto choice for high-bandwidth control loops such as field-oriented motor control, digital power conversion, and sensor-fusion front ends. Key features of the DSPIC33FJ256MC710-I/PT include a 40 MIPS modified-Harvard 16-bit core with DSP engine extensions (17-bit x 17-bit single-cycle multiplier and 40-bit accumulator), an 8-channel DMA controller, dual 10-bit/12-bit-configurable ADC modules supporting simultaneous sampling, motor-control PWM with dedicated time bases, an ECAN interface, and self-programmable Flash for in-field firmware upgrades. Architecturally, the dsPIC33F core integrates a 24-bit instruction word with 16-bit data paths, enabling both 16-bit MCU and DSP instruction sets in one binary-compatible ISA. Seamless migration paths to PIC24 MCUs and dsPIC30F DSCs in similar 100-pin TQFP packages are supported per the Microchip product page, allowing teams to scale memory or peripheral counts without redesigning the PCB. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous (PMSM) motor drives, single- and three-phase induction motor control, switched-reluctance drives, digital switch-mode power supplies, and industrial sensor-front-end processing. The motor-control PWM (with complementary outputs and programmable dead time) and dual simultaneous-sampling ADCs make this DSC particularly well-suited to sensorless field-oriented control (FOC). Multiple PGECx / PGEDx pin pairs are exposed for ICSP programming and debugging; the pair used must remain consistent, and every VDD / VSS pin must be connected, otherwise programming may fail. This page synthesizes distributor pricing, drop-in 100-pin TQFP alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256MC710A-E/PF

DSPIC33FJ256MC710A-E/PF - 16-bit DSC 40MIPS 256KB Flash | Microchip

The Microchip Technology DSPIC33FJ256MC710A-E/PF is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance from 256 KB flash and 30 KB SRAM, housed in a 100-pin TQFP (14x14 mm) package rated for -40C to +125C extended industrial operation. The part is the -E (extended) temperature variant of the MC710A motor-control family, supplied in tray packaging for design and production use. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and deterministic control of a microcontroller. Within the embedded-classification hierarchy, the dsPIC33F family sits above basic MCUs and below standalone DSPs, offering single-cycle MAC, hardware multiply, and divide alongside flash-based code storage. DSCs of this class are the workhorse architecture for digitally controlled power conversion and motion systems, where deterministic interrupt response and DSP-grade math are both mandatory. Key differentiators of this part include the A-silicon revision of the MC710 family, dedicated motor-control PWM modules with complementary outputs and dead-time insertion, fault inputs, a high-speed 10-bit ADC capable of 1.1 Msps, two ECAN interfaces for industrial networking, and quadrature encoder interfaces for closed-loop motion feedback. The 256 KB flash supports complex field-oriented control (FOC) algorithms with headroom for CANopen stacks and bootloaders. Architecturally, the dsPIC33F core executes an optimized C-compiler-friendly instruction set with two 40-bit accumulators, hardware modulo addressing, and bit-reversed addressing for FFTs. The MC variant tailors peripherals toward digital power: eight PWM generators with flexible trigger sources, analog comparators, and a fast ADC that can be triggered synchronously by the PWM for precise current sampling. Typical applications include brushless DC (BLDC), permanent-magnet synchronous (PMSM), single/three-phase induction, and switched reluctance motor drives, plus digital power supplies, solar inverters, and uninterruptible power supplies (UPS). On-chip ECAN makes it a natural fit for automotive-adjacent and industrial networked drives where CANopen or DeviceNet stacks are deployed. Design consideration: the 3.3 V core requires a clean supply with proper decoupling on all VDD and VDDCORE pins, and the 100-pin TQFP exposed pad must be soldered with adequate PCB copper for sustained 40 MIPS operation at +125C ambient. Use Microchip's MPLAB X IDE with the XC16 compiler for code development. This page synthesizes distributor pricing, drop-in same-package family alternatives, and practical design notes not found in the manufacturer datasheet, verified against Mouser, DigiKey, LCSC and Microchip sources as of 2026-10-07.

询价联系我们

DSPIC33FJ256MC710A-E/PT

DSPIC33FJ256MC710A-E/PT - 16-bit 40MIPS DSC 256KB | Microchip

The Microchip Technology DSPIC33FJ256MC710A-E/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS execution from 256KB (256K x 8) of Flash program memory and 30KB (30K x 8) of RAM, housed in a 100-pin TQFP (12x12 mm) package with an extended temperature range of -40C to +125C (E grade). A digital signal controller is a hybrid device that merges the control peripheral set of a microcontroller with the multiply-accumulate (MAC/DSP) instruction throughput of a digital signal processor. Within the power management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP, making it the standard choice for closed-loop power conversion where deterministic interrupt latency matters. The dsPIC33F family from Microchip Technology is one of the most widely deployed 16-bit DSC platforms in motor control and digital power. Key features of the MC710A variant include 85 general-purpose I/O pins, a 24-channel analog-to-digital converter supporting 10-bit and 12-bit modes, a CAN 2.0B controller, and the motor-control PWM peripherals (with center-aligned and complementary modes plus dead-time generators) that specifically target brushless DC, single-phase and 3-phase induction, and switched reluctance motor drives. Technically, the core runs at 3.0V to 3.6V with a 40 MIPS maximum clock, using a modified Harvard architecture with DSP multiply-accumulate, barrel shifter, and modulo/bit-reversed addressing for FFT and filter kernels. The 'A' revision adds industrial and automotive qualification; the -E/PT ordering code denotes the extended -40C to +125C temperature grade in a tape-free Tray package, and the family member is AEC-Q100 qualified per Microchip USA product data. Typical applications include BLDC and PMSM field-oriented-control motor drives, digital power supplies (PFC, LLC), solar inverters, and automotive auxiliary motor controllers requiring CAN networking. Design consideration: at 40 MIPS the core draws significant dynamic current; keep decoupling close to all VDD pins and budget Flash erase/write endurance by logging write cycles in your firmware. This page synthesizes distributor inventory data, drop-in alternatives, and engineering design notes not found in the manufacturer datasheet alone.

询价联系我们

DSPIC33FJ256MC710A-H/PF

DSPIC33FJ256MC710A-H/PF - 16-bit DSC 256KB Flash 40MIPS | Microchip

The Microchip Technology DSPIC33FJ256MC710A-H/PF is a 16-bit dsPIC33F digital signal controller (DSC) delivering up to 40 MIPS performance, 256KB (256K x 8) FLASH program memory, 30KB SRAM, and AEC-Q100 qualification, housed in a 100-pin TQFP (14x14x1 mm) package. A digital signal controller combines the compute architecture of a microcontroller with DSP-engine features such as a single-cycle MAC, hardware divide, and DSP multiply instructions. Within the power-management hierarchy, a DSC sits between general-purpose MCUs and dedicated DSPs, making the dsPIC33F family a bridge product that Microchip positions for seamless migration to PIC24 MCUs and dsPIC30F DSCs in similar packages. Key differentiating features include motor-control peripherals (PWM for brushless DC, single/3-phase induction and switched-reluctance motors), a broad connectivity suite covering CANbus, I2C, IrDA, LINbus, SPI, and UART/USART, and the -H temperature grade rated from -40C to +150C per distributor data. The AEC-Q100 qualification targets automotive and harsh industrial deployments. The 16-bit dsPIC core executes an optimized C compiler-friendly instruction set with DSP extensions. Program flash of 256KB provides headroom for complex field-oriented control (FOC) algorithms, while 30KB SRAM accommodates control loops, communication buffers, and telemetry. Analog integration and motor-control PWM peripherals reduce external component count in drive designs. Typical applications include BLDC and PMSM motor drives, industrial automation nodes using CAN, automotive body and powertrain auxiliaries, digital power supplies, and UPS/solar inverter control where deterministic 16-bit control loops and DSP math are required. Design consideration: the -H grade's 150C rating reduces allowable current and timing margins at the extremes; verify per the manufacturer datasheet electrical specifications and confirm whether your board supports the 40 MIPS operating range (DigiKey lists 20 MIPS for this ordering code). This page synthesizes distributor pricing, drop-in alternatives within the same 100-TQFP footprint, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ256MC710A-H/PT

DSPIC33FJ256MC710A-H/PT - 16-bit DSC 256KB Flash 20 MIPS | Microchip

The Microchip Technology DSPIC33FJ256MC710A-H/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC33FJ256MC710A family, delivering 20 MIPS of DSP-enhanced performance with 256KB (256K x 8) of Flash program memory and 30KB of SRAM, housed in a 100-pin TQFP (12x12 mm) surface-mount package. A Digital Signal Controller combines the peripheral set and programming model of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). In the power-management hierarchy, the dsPIC33F family sits between general-purpose MCUs such as the PIC24 and dedicated DSPs, offering single-cycle MAC, hardware division, and DSP engine features alongside familiar MCU peripherals like CAN, I2C, SPI, and UART. Key features include 20 MIPS core throughput at 3.3V operation, 256KB of self-programmable Flash, and 30KB of on-chip SRAM. Connectivity spans CANbus, I2C, IrDA, LINbus, SPI, and UART/USART, and integrated system peripherals include brown-out detection. The device is qualified to AEC-Q100 for automotive applications, making it suitable for harsh-environment motor control nodes. The dsPIC33FJ256MC710A is specifically optimized for motor control: the family explicitly supports brushless DC (BLDC) motors, single- and 3-phase induction motors, and switched reluctance motors. The DSP engine accelerates field-oriented control (FOC) loops, while CAN connectivity enables in-vehicle networking. Microchip documents seamless migration paths from dsPIC30F DSCs and PIC24 MCUs in similar packages, protecting software investment. Typical applications include automotive BLDC and PMSM motor drives, industrial 3-phase inverter control, switched reluctance motor systems, digital power conversion (PFC, LLC), and unified communication-motor-control nodes where CAN, LIN, or UART links must coexist with real-time PWM control. Design consideration: the H temperature-grade device operates over an extended automotive range in the 100-TQFP; verify your maximum junction temperature against the theta-JA of your PCB copper area, as high ambient motor-drive environments are the primary thermal constraint. Power the 3.3V core and I/O rails from a clean LDO or buck regulator with proper decoupling on all VDD/VDDCORE pins. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, with all specifications verified against live web data as of 2026-09-27.

询价联系我们

子分类

产品（39,000+)

DSPIC33FJ256GP510A-E/PT - 16-Bit DSC 256KB Flash | Microchip

DSPIC33FJ256GP510A-I/PF - 16-bit 40MIPS DSC 256KB Flash | Microchip

DSPIC33FJ256GP510A-I/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256GP510T-I/PT - 16-bit 40 MIPS DSC 256KB Flash | Microchip

DSPIC33FJ256GP710-I/PT - 16-bit DSC 40 MIPS 256KB Flash | Microchip

DSPIC33FJ256GP710A-E/PF - 16-bit DSC 40 MIPS 256 KB Flash | Microchip

DSPIC33FJ256GP710A-E/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256GP710A-H/PF - 16-bit DSC, 40 MIPS, 256KB Flash | Microchip

DSPIC33FJ256GP710A-H/PT - 16-bit 40 MIPs DSC 256KB | Microchip

DSPIC33FJ256GP710A-I/PF - 16-bit 40 MIPS DSC 256KB Flash TQFP-100 | Microchip

DSPIC33FJ256GP710A-I/PT - 16-bit 40MIPS 256KB DSC | Microchip

DSPIC33FJ256GP710AT-I/PF - 16-Bit 40MIPS 256KB Flash DSC | Microchip

DSPIC33FJ256GP710AT-I/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256GP710T-I/PT - 16-bit 40 MIPS DSC 256KB Flash | Microchip

DSPIC33FJ256MC510-I/PT - 16-Bit DSC 40 MIPS 256KB Flash | Microchip

DSPIC33FJ256MC510A-E/PT - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256MC510AT-I/PF - 16-bit 40 MIPS DSC 256KB Flash | Microchip

DSPIC33FJ256MC510T-I/PF - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256MC710-I/PF - 40MIPS 16-bit DSC 256KB Flash | Microchip

DSPIC33FJ256MC710-I/PT - 40 MIPS 16-bit DSC, 256KB Flash | Microchip

DSPIC33FJ256MC710A-E/PF - 16-bit DSC 40MIPS 256KB Flash | Microchip

DSPIC33FJ256MC710A-E/PT - 16-bit 40MIPS DSC 256KB | Microchip

DSPIC33FJ256MC710A-H/PF - 16-bit DSC 256KB Flash 40MIPS | Microchip

DSPIC33FJ256MC710A-H/PT - 16-bit DSC 256KB Flash 20 MIPS | Microchip