集成电路

子分类

📁 ADC/DAC 3,100+ 产品 📁 放大器IC 1,900+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 660+ 产品 📁 Comparator ICs 1 产品 📁 DSP 1,100+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 7,300+ 产品 📁 接口IC 3,300+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 460+ 产品 📁 存储IC 870+ 产品 📁 微控制器 20,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 14 产品

产品（39,000+)

MCF5280CVF66 - ColdFire V2 32-bit MCU, 66MHz, ROMless | NXP
MCF5280CVF66

MCF5280CVF66 - ColdFire V2 32-bit MCU, 66MHz, ROMless | NXP

The NXP MCF5280CVF66 is a 32-bit ColdFire V2 microcontroller running at 66MHz with ROMless memory architecture, housed in a 256-ball MAPBGA package measuring 17x17 mm. It integrates a ColdFire V2 core with on-chip Ethernet, CAN, and a rich peripheral set optimized for embedded networked applications. The device is part of the MCF528x family designed to simplify networked MCU designs where external flash memory is preferred over on-chip non-volatile storage. A ColdFire microcontroller is a 32-bit RISC processor architecture developed by Freescale (now NXP) that evolved from the Motorola 68000 family, offering MIPS-class performance with a simplified instruction set for embedded applications. Within the broader taxonomy it sits as a microcontroller -> embedded processor -> 32-bit MCU -> RISC MCU -> ColdFire family, providing higher performance than 8/16-bit alternatives while retaining deterministic real-time behavior for industrial control. The V2 core implements a Variable-Length RISC (VLR) pipeline optimized for code density and interrupt latency. Key features of the MCF5280CVF66 include 66 MHz core clock, integrated 10/100 Ethernet MAC, dual CAN 2.0b controllers, multiple UARTs, QSPI, I2C, a 12-bit ADC, and FlexBus external bus interface for memory expansion. The ROMless configuration means external boot and program memory are required, enabling flexible memory sizing for each design. The 256-MAPBGA package supports high pin density for industrial networking and embedded control applications requiring multiple serial interfaces. The architecture pairs the ColdFire V2 core with crossbar switch for peripheral access, providing deterministic bandwidth for Ethernet and CAN traffic. Integrated PHY interface and DMA channels reduce external component count, and the 16-channel eDMA controller supports scatter-gather transfers for high-throughput data movement. The JTAG and BDM debug interfaces support real-time trace and hardware breakpoint debugging. Typical applications include industrial Ethernet gateways, CAN-based factory automation nodes, building automation controllers, point-of-sale terminals, and networked sensor hubs. The combination of Ethernet plus dual CAN makes it suitable for protocol bridges between factory-floor networks and enterprise systems. Designers should note that the MCF5280CVF66 is in NRND (Not Recommended for New Designs) lifecycle status per NXP; for new designs the Kinetis or i.MX RT crossover MCU families are recommended successors.

询价 联系我们
MCF5280CVF66J - Coldfire V2 32-bit MCU 66MHz ROMless | NXP
MCF5280CVF66J

MCF5280CVF66J - Coldfire V2 32-bit MCU 66MHz ROMless | NXP

The NXP Semiconductors MCF5280CVF66J is a 32-bit Coldfire V2 microcontroller based on the MCF528x family, delivering up to 66 MHz CPU performance with no on-chip flash (ROMless) and housed in a 256-ball MAPBGA package measuring 17x17 mm. It integrates 2 KB of SRAM, 16 KB of cache, and a rich peripheral set including Fast Ethernet, CAN, UART, SPI, I2C, and a 12-bit ADC. A Coldfire microcontroller is a 32-bit embedded processor family based on the Motorola 68000 instruction set architecture (ISA), engineered for low-cost, high-throughput control applications. The MCF5280 sits within the broader taxonomy of microcontroller -> embedded processor -> system-on-chip -> semiconductor, and was positioned for connectivity-rich industrial designs where deterministic Ethernet and CAN performance mattered more than flash density. Key features include an integrated 10/100 Fast Ethernet MAC with MII/RMII interface, dual CAN 2.0B controllers, USB 1.1 (device mode on selected revisions), 4-channel 32-bit DMA, and a 4-channel 32-bit timers. The device operates across an industrial -40C to +85C temperature range with 3.3V I/O and 1.5V core supply. Multi-layer AHB/APB bus architecture enables concurrent DMA and CPU transactions, supporting real-time Ethernet throughput. The MCF5280CVF66J uses a variable-length RISC Coldfire V2 core with enhanced multiply-accumulate (EMAC) unit, achieving 56 Dhrystone MIPS at 66 MHz. Memory map supports external SDRAM and flash interfaces through a 32-bit local bus plus dedicated chip-select controllers. Trace and debug are supported via BDM/JTAG, with on-chip breakpoint hardware. Typical applications include industrial Ethernet PLC nodes, factory automation gateways, CAN-based motor controllers, building-automation routers, and networked sensor concentrators. The combination of Ethernet + CAN makes it well-suited for SCADA and remote I/O designs. When designing with this ROMless part, designers must pair the MCF5280CVF66J with external NOR flash on the local bus. Total BOM cost typically requires placing 4-8 MB of 16-bit SRAM/flash externally. Power sequencing between 3.3V and 1.5V rails must follow NXP's reference manual; the 1.5V core rail must stabilize within 50 ms of the 3.3V rail for clean BDM debug handshake. This page synthesizes distributor pricing, same-family and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet - giving engineers a one-stop reference for both new designs and EOL/EOL risk migration paths.

询价 联系我们
MCF5280CVF80 - Coldfire V2 32-bit MCU 80MHz 256-MAPBGA | NXP
MCF5280CVF80

MCF5280CVF80 - Coldfire V2 32-bit MCU 80MHz 256-MAPBGA | NXP

The NXP MCF5280CVF80 is a ColdFire V2 32-bit RISC microcontroller integrated circuit operating at 80 MHz, supplied in a 256-ball 17 x 17 mm MAPBGA package, with part status marked Obsolete. The device belongs to the MCF528x family and integrates Ethernet, CANbus, UART/USART, I2C, and SPI connectivity along with DMA, LVD, POR, PWM, and a watchdog timer, with 142 user I/O pins. A microcontroller (MCU) is a single-chip processing system that combines a CPU core, volatile and non-volatile memory, peripherals, and I/O in one package. ColdFire represents NXP/Freescale's 32-bit variable-length RISC architecture descended from the 68000 family, positioned between 8-bit MCUs and higher-end applications processors. Microcontrollers sit at the lowest tier of programmable logic hierarchy, above discrete logic ICs and below microprocessors/MPUs that require external memory and peripherals. MAPBGA (Mold Array Process Ball Grid Array) is a plastic BGA package family optimized for high-pin-count surface-mount designs where board space and signal integrity dominate. Key features of the MCF5280CVF80 include 80 MHz ColdFire V2 core speed, ROMless program memory (external memory interface required), 142 I/O pins, and operating voltage referenced around 3.3 V typical. The integrated 10/100 Ethernet MAC makes it well suited for connected embedded systems, while the CANbus controller addresses industrial and automotive networking. Hardware DMA, PWM, and watchdog timers reduce CPU overhead in real-time control loops. Architecturally, the ColdFire V2 core delivers a balance of code density and 32-bit throughput while keeping power and cost low. The MAPBGA footprint places traces and power/ground balls under the die for low inductance, and the wide connectivity set means a single MCF5280 device can replace a multi-chip UART/CAN/Ethernet external stack. Typical applications include industrial Ethernet gateways, building automation controllers, motor-control front-ends, automotive telematics (non-safety-relevant), and point-of-sale terminals. Engineers also deploy it in CAN/Ethernet bridges, SCADA remote terminal units, and intelligent sensor hubs. When designing with this part, observe thermal limits of the MAPBGA package and use a multi-layer PCB with stitched ground/thermal vias under the central ball grid for heat extraction. Because the part is Obsolete, verify Last Time Buy windows and plan second-source or migration to an active ColdFire/Kinetis equivalent before prototype freeze. This page synthesizes DigiKey stock data, parametric drop-in alternatives, lifecycle status, and practical design guidance not consolidated on any single manufacturer page.

询价 联系我们
MCF5280CVM66 - 32-bit ColdFire V2 MCU 66MHz ROMless | NXP
MCF5280CVM66

MCF5280CVM66 - 32-bit ColdFire V2 MCU 66MHz ROMless | NXP

The NXP MCF5280CVM66 is a 32-bit ColdFire V2 microcontroller running at 66 MHz, supplied in a 256-ball MAP-BGA (17x17 mm) package, and is the ROMless variant of the MCF528x family with integrated Ethernet and CAN peripherals. A ColdFire V2 MCU is a 32-bit RISC microcontroller based on the legacy Motorola 68000 instruction set, optimized for embedded networking and industrial control. Within the broader taxonomy, the MCF5280 sits as a ColdFire V2 core -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The ColdFire family targets cost-sensitive networked applications where deterministic performance, low power, and on-chip communications peripherals are essential. Key features include the ColdFire V2 core with 66 MHz maximum CPU clock, ROMless program memory (external memory interface supported), integrated 10/100 Ethernet MAC, CAN 2.0 controller, multiple UARTs, QSPI, I2C, and a rich timer and GPIO set. The 256-MAPBGA package exposes the full external bus and peripheral set required for industrial communication designs, with a single 3.3 V supply and 1.8 V internal core LDO. Technically, the device implements a variable-length RISC pipeline, hardware multiply/divide, and a unified memory architecture where SRAM and external memory share a single bus. The Ethernet MAC supports MII/RMII for external PHYs, while the CAN module provides 16 message buffers compliant with CAN 2.0B. Debug is supported through Background Debug Mode (BDM) and JTAG. Typical applications include industrial Ethernet gateways, CAN-based factory automation nodes, building automation controllers, embedded web servers, and motor control front-ends. The integrated communications peripherals make it well-suited for protocols such as Modbus TCP, EtherNet/IP, and CANopen without requiring external bridge chips. When designing with the MCF5280CVM66, pay close attention to BGA PCB layout - the 256-ball MAPBGA requires via-in-pad or dog-bone fanout and controlled impedance traces for the external memory bus. Decoupling must include both bulk and high-frequency ceramics placed close to each supply pin cluster to keep the ColdFire core stable during Ethernet traffic bursts. This page synthesizes current distributor pricing, lifecycle status (NRND per NXP), pin-compatible drop-in alternatives such as MCF5282CVM66 and MCF5280CVM80, and practical design notes that go beyond the manufacturer datasheet.

询价 联系我们
MCF5280CVM66J - 32-bit ColdFire V2 MCU 66MHz | NXP
MCF5280CVM66J

MCF5280CVM66J - 32-bit ColdFire V2 MCU 66MHz | NXP

The NXP Semiconductors MCF5280CVM66J is a 32-bit microcontroller based on the ColdFire V2 core, operating at 66 MHz in a 256-ball MAPBGA (17x17 mm) package. It is ROMless (no internal flash) with 64 KB of on-chip SRAM, integrates CAN bus and Ethernet communications peripherals with an external bus interface (EBI/EMI), and operates from a 2.7 V to 3.6 V supply. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals for embedded control. Within the power-management hierarchy of embedded systems, the MCF528x family targets networked applications where the MCU sits at the node level, connecting sensors and actuators to industrial Ethernet and CAN networks. The ColdFire V2 architecture descends from the classic Motorola 68K lineage, providing a mature, well-documented 32-bit instruction set. Key features include the 66 MHz ColdFire V2 single-core processor, integrated Ethernet MAC and CAN 2.0B controller for industrial networking, a rich peripheral set (UARTs, timers, ADC, QSPI), and the 256-MAPBGA footprint that conserves board area in space-constrained designs. The ROMless MCF5280 variant requires external program memory, which allows designers to size and select code storage independently. Technically, the MCF5280 executes code from external memory through the external bus interface, while data and stack reside in the 64 KB on-chip SRAM (64K x 8). This architecture suits applications where firmware is updated frequently or stored in large external flash devices. The integrated Fast Ethernet controller and CAN module reduce external component count, and the device is supported by the mature CodeWarrior toolchain. Typical applications include industrial Ethernet nodes, building automation controllers, CAN-networked devices, and factory automation equipment. Its integrated networking peripherals make it especially efficient for gateway designs bridging CAN fieldbus to Ethernet backbones. A key design consideration is that being ROMless, the MCF5280CVM66J must boot from external memory, so boot flash sizing, bus loading, and power-up timing deserve early attention. Note this part is reported obsolete by distributor data, so new designs should evaluate alternatives. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
MCF5280CVM80 - 80MHz ColdFire V2 MCU, ROMless, 256-MAPBGA | NXP
MCF5280CVM80

MCF5280CVM80 - 80MHz ColdFire V2 MCU, ROMless, 256-MAPBGA | NXP

The NXP MCF5280CVM80 is a 32-bit ColdFire V2 microcontroller in the MCF528x family, operating at 80 MHz with no on-chip flash (ROMless), housed in a 256-ball MAPBGA package (17x17 mm). A ColdFire microcontroller is a 32-bit reduced instruction set computing (RISC) processor family based on the Motorola 68000 architecture, designed to balance high throughput with low power consumption in embedded systems. ColdFire V2 cores integrate the ColdFire instruction set, debug module, and peripheral bridges into a single die, placing this MCU in the hierarchy: microcontroller -> embedded processor -> 32-bit MCU -> semiconductor IC. The V2 variant is the smallest ColdFire core, optimized for cost-sensitive and deterministic real-time control. Key features of the MCF5280CVM80 include an 80 MHz ColdFire V2 core, ROMless operation requiring external program memory, integrated 10/100 Ethernet MAC for networked embedded applications, dual CAN 2.0B controllers for industrial networking, and a comprehensive peripheral set including UARTs, I2C, QSPI, and timers. The 256-MAPBGA package supports high pin-count peripherals and is suitable for industrial-grade embedded designs operating from -40C to +85C. The device integrates an enhanced multiplyaccumulate (EMAC) unit and a hardware debug module for non-intrusive background debugging. With its ROMless architecture, the MCF5280CVM80 is intended for applications that require large external NOR flash or SRAM, allowing field upgrades and code flexibility. The ColdFire V2 core executes the ColdFire instruction set with deterministic interrupt latency, supporting real-time operating systems (RTOS) and bare-metal firmware. Typical applications include industrial Ethernet nodes, building automation gateways, CAN-based factory automation controllers, and embedded networked sensor hubs. The integrated Ethernet MAC and dual CAN peripherals make the part especially attractive for protocol-conversion gateways between Ethernet and CAN networks, including Modbus TCP to CANopen bridges used in industrial control cabinets. When designing with this part, ensure the external memory interface is properly terminated and that the 256-ball BGA is assembled via reflow with appropriate thermal profiling. The ROMless architecture means the MCU will not boot without valid code in external memory - a bootloader strategy must be planned at the system level. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
MCF5280CVM80J - ColdFire V2 80MHz 32-bit MCU | NXP
MCF5280CVM80J

MCF5280CVM80J - ColdFire V2 80MHz 32-bit MCU | NXP

The NXP MCF5280CVM80J is a 32-bit microcontroller from the ColdFire V2 MCF528x family, delivering 80 MHz CPU performance in a 256-pin MAPBGA (17x17 mm) package. It is a ROMless variant of the MCF528x line, with 256 MAPBGA (17x17) outline, integrated Ethernet and CAN peripherals (as documented for the broader MCF528X family), and is specified for industrial temperature operation. The 'J' suffix indicates an industrial-grade temperature rating of -40C to +105C (junction) and a Pb-free/RoHS-compliant lead-free reflow profile per NXP/Freescale part numbering. What is a ColdFire V2 microcontroller? ColdFire is a 68k-architecture-derived 32-bit instruction set originally developed by Motorola, then Freescale, and now maintained by NXP. The V2 core variant targets cost-sensitive embedded networking and industrial applications, balancing processing throughput against deterministic interrupt latency, and sits in the broader product hierarchy: ColdFire V2 -> ColdFire family -> 32-bit microcontroller -> embedded MCU. ROMless parts such as the MCF5280CVM80J are intended for systems that pair the MCU with an external flash memory bank, allowing the OEM to choose memory density, boot strategy, and security layout independently from the processor silicon. Key features include 80 MHz maximum CPU clock, 32-bit ColdFire V2 core, ROMless program memory interface, integrated 10/100 Ethernet MAC, CAN 2.0 controller, multiple UART/SPI/I2C channels, 16-bit timer units, and an external memory controller for SRAM/flash expansion. The device supports JTAG/BDM debug and is supported by NXP's CodeWarrior and the broader ColdFire toolchain. The 256-ball MAPBGA package provides high I/O density for embedded networking and human-machine interface (HMI) designs where board space is at a premium. The MCF5280 architecture combines a ColdFire V2 core with on-chip SRAM and a sophisticated peripheral set designed for Ethernet- and CAN-connected industrial nodes. ROMless operation means the external memory controller drives an external flash and SRAM, giving designers flexibility in choosing boot memory, security features, and in-field firmware update strategy. Industrial temperature grading and a 17x17 mm BGA footprint make it suitable for factory automation controllers and ruggedized embedded modules. Typical applications include industrial automation controllers, embedded Ethernet nodes, CAN-based motor control front-ends, building automation gateways, and point-of-sale terminals. For cost-sensitive variants in the same family the MCF5281/5282/5283 add on-chip flash, while ROMless members such as this part are chosen when external memory density or firmware partitioning is required. When designing with this device, ensure PCB layout provides continuous ground and a low-impedance supply for the BGA core. Trace length matching on the Ethernet MII bus to the PHY is critical to keep signal integrity within IEEE 802.3 timing masks. Borehole-in-pad BGA assembly requires via-in-pad plating for thermal and electrical reliability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - including a coldfire v2 80MHz MCU with romless program memory layout.

询价 联系我们
MCF5281CVF66 - 32-bit ColdFire V2 MCU 256KB Flash 66MHz | NXP
MCF5281CVF66

MCF5281CVF66 - 32-bit ColdFire V2 MCU 256KB Flash 66MHz | NXP

The NXP MCF5281CVF66 is a 32-bit ColdFire V2 microcontroller featuring a V2 core running at 66 MHz, 256 KB of on-chip Flash memory, and a 256-ball MAPBGA (17x17 mm) package. It is part of the MCF528x family and integrates 10/100 Ethernet MAC, CAN, UART, I2C, SPI, and a flexible external bus interface for industrial connectivity. A ColdFire microcontroller is a 32-bit microprocessor core based on the Motorola 68000 instruction set architecture, optimized for embedded control with low power consumption and high code density. The MCF5281 sits within the broader taxonomy of 32-bit MCU -> microcontroller -> embedded processor -> semiconductor, targeting connected industrial and building-automation designs where deterministic response and Ethernet/CAN connectivity are required. Key features include 256 KB (256K x 8) Flash program memory, 8 KB SRAM data memory, 10/100 Mbps Fast Ethernet MAC with MII/RMII interface, two CAN 2.0B controllers, four DMA channels, a 16-channel eTPU timer co-processor for complex timing, an 8-channel 10-bit ADC, and an integrated Phase-Locked Loop (PLL) clock generator. The ColdFire V2 core delivers 56 MIPS (Dhrystone 2.1) at 66 MHz while consuming very low active power, suitable for fanless industrial nodes. The device integrates a 32-bit ColdFire V2 core with 4 GB unified address space, hardware multiply/accumulate, hardware divider, and JTAG/BDM debug interface. It uses a 3.3 V I/O supply with 1.5 V internal core voltage generated by the on-chip voltage regulator. The 256-MAPBGA package exposes a wide external bus (EMAC) for SDRAM and external peripherals, with PCI Revision 2.2 bus support on select package variants. Typical applications include industrial Ethernet I/O blocks, building-automation controllers (BACnet, Modbus TCP), CAN-based motor and sensor gateways, point-of-sale terminals, and serial-to-Ethernet protocol converters. The 256 KB Flash is well suited to IPv4/IPv6 stacks with TLS, BACnet, and CANopen firmware profiles typical of these markets. When designing with this part, allocate careful PCB layout for the BGA substrate escape and use at least four PCB layers with a continuous ground plane under the package. The integrated Ethernet MAC still requires an external PHY magnetics, RJ-45 jack, and termination network; the CAN transceivers and pull-ups are also external. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing the MCF5281CVF66 in 2026.

询价 联系我们
MCF5281CVF80 - ColdFire V2 32-bit MCU, 80MHz, 256KB Flash | NXP
MCF5281CVF80

MCF5281CVF80 - ColdFire V2 32-bit MCU, 80MHz, 256KB Flash | NXP

The NXP (formerly Freescale) MCF5281CVF80 is a ColdFire V2 32-bit microcontroller running at 80MHz with 256KB of on-chip FLASH program memory, housed in a 256-ball MAPBGA (17x17 mm) package. It integrates a rich peripheral set including a 10/100 Ethernet MAC, CANbus, three UARTs, two I2C, and a QSPI, exposing 142 GPIO pins. A ColdFire V2 microcontroller is a 32-bit reduced instruction set computing (RISC) microprocessor core originally developed by Motorola/Freescale (now NXP) as a variable-length instruction follow-on to the 68000 family. ColdFire V2 sits in the middle of the ColdFire V1-V5 hierarchy, balancing code density, deterministic interrupt latency, and MHz-class performance for embedded networking and industrial control. MCF528x devices specifically belong to the broader MCU -> 32-bit MCU -> ColdFire -> networking/connected MCU taxonomy and remain a long-life platform for industrial automation, building control, and edge connectivity. Key features of the MCF5281CVF80 include a 32-bit ColdFire V2 core with hardware multiply/accumulate, an integrated 10/100 Mbps Fast Ethernet controller with MII/RMII PHY interface, dual CAN 2.0B controllers, an external bus interface (EBI/EMI) for SRAM/ROM/Flash expansion, DMA, LVD, POR, PWM, and a watchdog timer. The device operates from a 3.0V to 3.6V single supply and includes an industrial-grade temperature option per the CVF80 part suffix. Architecturally, the MCF5281 pairs the ColdFire V2 core with a unified memory map and SRAM/FLASH tightly coupled for deterministic fetch. The on-chip peripherals are routed through a crossbar to keep DMA and CPU traffic from stalling the bus, which makes the part a fit for protocol stacks that mix Ethernet, CAN, and serial traffic simultaneously. Typical applications include industrial Ethernet gateways, building automation controllers (BACnet/Modbus TCP), CAN-to-Ethernet bridges, motor control front-ends, and point-of-sale/embedded networking appliances where a 32-bit core plus integrated MAC and CAN reduces BOM and PCB area versus a discrete MCU+ASIC approach. When designing with this part, allocate sufficient PCB area for the 17x17 mm MAPBGA and use at least 4-layer routing with microvia fan-out for the inner balls. Provide a clean 3.3V rail with bulk decoupling near the EBI power pins to keep Ethernet PHY signaling within the IEEE 802.3 template. This page synthesizes distributor pricing for the MCF5281CVF80, lists verified drop-in alternatives from the same ColdFire MCF528x family, and consolidates practical design notes that complement the manufacturer datasheet.

询价 联系我们
MCF5281CVM66 - ColdFire V2 MCU 32-bit 66MHz 256KB Flash 256-MAPBGA | NXP
MCF5281CVM66

MCF5281CVM66 - ColdFire V2 MCU 32-bit 66MHz 256KB Flash 256-MAPBGA | NXP

The NXP MCF5281CVM66 is a 32-bit ColdFire V2 microcontroller (MCU) running at 66 MHz with 256 KB of on-chip flash memory, integrated Ethernet and CAN peripherals, packaged in a 256-ball MAPBGA (17x17 mm). According to the manufacturer product page, the part carries an NRND (Not Recommended for New Designs) lifecycle flag, indicating it remains available for existing designs but NXP is steering new projects to successor ColdFire parts. A ColdFire microcontroller belongs to the M68k microprocessor family (Motorola 68000 instruction set lineage) and occupies a middle ground between 8/16-bit legacy MCUs and full 32-bit PowerPC cores. The ColdFire V2 core delivers deterministic interrupt response, a unified 32-bit address space, and significantly higher code density than typical ARM Cortex-M parts at comparable MHz. Within the broader taxonomy, MCF5281CVM66 sits as: 32-bit microcontroller -> ColdFire V2 -> MCF528x family -> embedded MCU with Ethernet/CAN, suitable for industrial control, building automation, and networked sensor gateways. Key features include 256 KB flash with 8 KB SRAM (typical for the MCF528x family), 10/100 Ethernet MAC, FlexCAN module, three UARTs, QSPI, I2C, an eTPU timer coprocessor, a 4-channel 12-bit (or 10-bit, family-dependent) ADC, and a hardware encryption accelerator (CAU on some MCF5281 mask sets). Supply voltage is 3.3 V I/O with internal 1.5 V core regulation. The 256-MAPBGA package supports a 17x17 mm body and is intended for industrial temperature ranges (typically -40C to +85C). Architecturally, the device integrates a ColdFire V2 core with a unified 4-channel DMA, memory management with protection, and tightly-coupled peripheral bus. The Ethernet MAC supports MII/RMII PHY interfaces, making the MCU a turnkey solution for embedded TCP/IP nodes. The FlexCAN module is CAN 2.0B compliant and supports industrial automation protocols like CANopen and DeviceNet. Typical applications include industrial Ethernet gateways, HVAC controllers, building automation nodes, CAN-to-Ethernet bridges, networked sensor hubs, and legacy factory automation retrofit boards. The combination of Ethernet, CAN, and ample flash makes the MCF5281 a long-standing choice for industrial connectivity designs that predate widespread Cortex-M adoption. Designers should pay attention to the 3.3 V supply tolerance - this part does not support 5 V inputs on any GPIO. The 256-MAPBGA package requires multi-layer PCB with microvia or via-in-pad technology for reliable assembly; 4-layer stack-up minimum. For new designs, evaluate the RT1060 or i.MX RT crossover MCU families as modern successors. This page synthesizes distributor pricing from DigiKey and Mouser, NXP lifecycle status, parametric comparisons against other ColdFire V2 variants (MCF5282CVM80, MCF5214CVM66, MCF5213LCVM80), and practical design notes not consolidated on the manufacturer product page.

询价 联系我们
MCF5281CVM66J - ColdFire V2 32-Bit MCU, 66MHz, 256KB Flash, 256-MAPBGA | NXP
MCF5281CVM66J

MCF5281CVM66J - ColdFire V2 32-Bit MCU, 66MHz, 256KB Flash, 256-MAPBGA | NXP

The NXP MCF5281CVM66J is a 32-bit ColdFire V2 microcontroller integrated with 256 KB of on-chip flash memory, a 66 MHz CPU core, and a rich communications peripheral set including 10/100 Ethernet MAC, CAN, three UARTs, an I²C bus, and queued SPI. Housed in a 256-ball MAPBGA package measuring 17 x 17 mm, the device targets embedded networked applications that previously required an external MCU plus a separate communications controller. According to the NXP MCF528X product page, the family is "designed to simplify embedded Ethernet-networked MCU applications" by integrating MAC and PHY interfaces alongside the ColdFire V2 core. A ColdFire V2 microcontroller is a 32-bit embedded processor derived from the original 68000 instruction set architecture (ISA), optimized for code density and deterministic real-time response. ColdFire sits within the broader hierarchy of microcontrollers -> 32-bit MCUs -> ColdFire family -> V2 core microcontrollers. It is commonly used in industrial control, factory automation, and connected-device designs where legacy 68K code can be retained while taking advantage of modern peripherals and integrated Ethernet. Key features of the MCF5281CVM66J include 256 KB flash program memory, 32 KB or more of SRAM (family-dependent), an enhanced multiply-accumulate unit (EMAC), four 32-bit timers plus a 16-bit periodic interrupt timer, eight-channel flexible 12-bit (or 10-bit family-dependent) ADC on selected variants, real-time clock with 32 kHz crystal support, and a low-voltage detect / power-on reset supervisor. The integrated Fast Ethernet controller with media-independent interface (MII) eliminates the need for an external MAC chip, reducing BOM cost and PCB area in connected industrial nodes. The ColdFire V2 core uses a variable-length RISC-like encoding derived from the Motorola 68000, executing most instructions in a single cycle and providing deterministic interrupt latency suitable for hard real-time control loops. The peripheral set is connected via an enhanced time-multiplexed bus, allowing DMA-driven data movement between Ethernet, CAN, and on-chip RAM with minimal CPU overhead. Typical applications include industrial Ethernet nodes (PROFINET, EtherNet/IP, Modbus TCP), CAN-based motor controllers and servo drives, building-automation gateways, point-of-sale terminals, and embedded web servers. The combination of 66 MHz performance, on-chip Ethernet MAC, and CAN is particularly well suited to factory-floor devices that must bridge fieldbus and enterprise networks. When designing with this part, ensure the 256-MAPBGA land pattern matches the JEDEC MS-034 package outline and that the four-layer PCB stack-up meets the impedance requirements for the MII Ethernet signals. Decoupling must include a 0.1 µF ceramic capacitor per logic supply pin plus bulk tantalum or polymer capacitors near the package. This page synthesizes distributor inventory data from DigiKey, Mouser, Octopart, and Rochester Electronics together with drop-in same-family alternatives and practical design notes not aggregated in any single manufacturer document.

询价 联系我们
MCF5281CVM80 - 80MHz ColdFire V2 MCU 256KB Flash | NXP
MCF5281CVM80

MCF5281CVM80 - 80MHz ColdFire V2 MCU 256KB Flash | NXP

The NXP Semiconductors MCF5281CVM80 is a 32-bit ColdFire V2 microcontroller running at 80 MHz, integrating 256 KB of program flash and 64 KB of SRAM in a 256-ball MAP-BGA (17x17 mm) package. The part combines an Ethernet MAC, CAN module, and a rich set of serial peripherals (UART, I²C, SPI) on-chip, targeting industrial networked-embedded applications. Its 142 user I/O pins and external bus interface provide flexibility for legacy 8/16-bit memory glue logic alongside modern peripheral expansion. A ColdFire V2 microcontroller is a 32-bit RISC-style processor derived from the original Motorola 68000 instruction set architecture. ColdFire V2 implementations keep the variable-length instruction encoding of the classic M68K while adding a more compact pipeline, on-chip MAC units in higher SKUs, and integrated peripherals. Within NXP's lineup, ColdFire V2 sits between the entry-level ColdFire V1 (smaller flash, simpler peripherals) and the more powerful ColdFire V3/V4 cores (MMU, higher MHz). It is best characterized as a mid-range 32-bit MCU for deterministic real-time control with integrated connectivity. Key differentiating features of the MCF5281CVM80 include the integrated 10/100 Ethernet MAC with DMA, a CAN 2.0B controller, four DMA channels for offloading data movement, and hardware acceleration for cryptographic-style operations in the same family. The 256-MAPBGA package exposes the full external bus (EBI/EMI), which lets designers connect SDRAM, NOR flash, or ASIC peripherals. Programmable peripherals (PWM timers, watchdog, low-voltage detect, and power-on reset) cover the industrial control safety baseline. Architecturally, the MCF5281CVM80 uses a unified instruction/data path with Harvard-style bus splits between flash and SRAM, allowing single-cycle access to RAM. The ColdFire V2 core executes most instructions in one clock, delivering 80 Dhrystone MIPS at 80 MHz core clock. The on-chip voltage regulator generates 1.3-1.5 V internal logic from an external 3.3 V supply, simplifying board power design. The 256-MAPBGA package provides ample ground returns for the 80 MHz core. Typical applications include industrial Ethernet PLCs, building automation gateways, factory-floor protocol bridges, and motor-control front-ends. Industrial Ethernet protocols such as EtherNet/IP, Modbus TCP, and PROFINET can run on the integrated MAC and DMA infrastructure. The CAN interface also enables the part to serve as a CAN-to-Ethernet bridge, a popular topology in automotive test equipment and factory automation. When designing with the MCF5281CVM80, place four-layer decoupling capacitors (100 nF + 10 µF bulk) directly under the BGA on the inner power plane to control switching noise. The 256-ball MAPBGA requires X-ray or AOI inspection on the production line, since hidden solder joints cannot be optically inspected. Designers must also consider that this part is marked NXP NRND (Not Recommended for New Designs); for new designs, evaluate the MCF5282 or Kinetis family as pin-compatible successors. This page consolidates distributor pricing, drop-in alternative guidance, and practical layout notes that go beyond the manufacturer datasheet. By comparing verified inventory across DigiKey, Mouser, and Octopart, this page supports engineers planning NRND transitions and procurement teams managing last-time-buy windows.

询价 联系我们
MCF5282CVF66 - ColdFire V2 32-bit MCU, 512KB Flash, 66MHz | NXP
MCF5282CVF66

MCF5282CVF66 - ColdFire V2 32-bit MCU, 512KB Flash, 66MHz | NXP

The NXP Semiconductors MCF5282CVF66 is a 32-bit ColdFire V2 microcontroller (MCU) with 512KB on-chip Flash and 64KB SRAM, running at 66 MHz in a 256-pin MAPBGA (17x17 mm) package, integrating 10/100 Ethernet MAC, CAN 2.0, and a rich peripheral set for networked embedded designs. ColdFire V2 microcontrollers are 32-bit RISC processors derived from the original Motorola 68000 instruction set architecture. Positioned between 8/16-bit legacy MCUs and higher-end ColdFire V3/V4 parts, the V2 core delivers single-cycle MAC (multiply-accumulate) instructions, hardware divide, and deterministic interrupt response, while keeping silicon area and power consumption lower than ARM Cortex-M3 equivalents from the same era. MCF5282CVF66 belongs to the MCF528x family, which is designed to simplify embedded Ethernet-networked MCU applications by combining the ColdFire core with industry-standard wired-communications peripherals on a single die. Key features include 512KB of program Flash (organized 512K x 8), 64KB of SRAM, 142 general-purpose I/O lines, 10/100 Mbps Ethernet MAC (MII/RMII), dual CAN 2.0A/B controllers, three UARTs, two I2C buses, QSPI, a 4-channel 32-bit DMA, an 8-channel 10-bit ADC, and an integrated phase-locked loop (PLL) for flexible clock generation. The 66 MHz core frequency provides 56 Dhrystone MIPS of integer throughput, sufficient for protocol stacks, supervisory control loops, and basic HMI tasks. Architecture depth: the ColdFire V2 core uses a variable-length instruction pipeline and Harvard-style bus structure with separate Flash and SRAM buses, so instruction fetches and data accesses do not contend for the same bus. The on-chip voltage regulator generates the 1.5V core logic from a single 3.3V external supply, simplifying PCB power design. The MAPBGA-256 package exposes a 17x17 mm footprint with 1.0 mm ball pitch and is rated for the standard 0 to 70C commercial operating range for this part suffix (V = -40 to +85C not used here; this part is the C commercial variant). Typical applications include industrial Ethernet gateways, factory automation PLCs, building-automation controllers, CAN-bridge / CAN-Ethernet converters, point-of-sale terminals, and embedded web servers. The integrated Ethernet and CAN peripherals make it especially suited to bridging legacy serial or CAN-based field devices onto TCP/IP networks. Design consideration: the 256-ball MAPBGA requires 4-layer (or preferably 6-layer) PCB stack-up with laser-drilled or via-in-pad microvias for reliable assembly; routing fan-out below the package is non-trivial and should be evaluated using the manufacturer's reference layout. The part operates from a single 3.3V rail; on-chip LDO generates the 1.5V core supply. This page synthesizes distributor pricing, NRND lifecycle status, and drop-in same-family alternatives not consolidated on the manufacturer product page.

询价 联系我们
MCF5282CVF66J - 32-bit ColdFire V2 MCU 512KB Flash 66MHz | NXP
MCF5282CVF66J

MCF5282CVF66J - 32-bit ColdFire V2 MCU 512KB Flash 66MHz | NXP

The NXP MCF5282CVF66J is a 32-bit ColdFire V2 microcontroller from the MCF528x family with 512KB of Flash memory, a 66 MHz core clock, and integrated 10/100 Ethernet plus CAN peripherals, housed in a 256-ball MAPBGA (17x17 mm) package. It addresses embedded networked control applications that need deterministic performance, on-chip Flash, and rich connectivity while keeping PCB area compact. A ColdFire microcontroller is a 32-bit RISC-style processor core derived from the legacy Motorola 68000 family and now maintained by NXP. Within the MCU hierarchy, ColdFire sits between traditional 8/16-bit controllers and high-performance ARM Cortex-M cores, targeting connected industrial nodes where deterministic interrupt response, on-chip Ethernet/CAN, and moderate code density matter more than raw Dhrystone throughput. The MCF528x line specifically simplifies embedded Ethernet-networked MCU designs by integrating MAC, CAN, multiple UARTs, QSPI, I2C, DMA, timers, and PWM on a single die. Key features include an integrated 10/100 Ethernet MAC supporting MII/RMII PHYs, a CAN 2.0B controller for industrial fieldbus, four DMA channels, a low-voltage detector with power-on reset, a watchdog timer, eight PWM channels, and 150 general-purpose I/Os. The 66 MHz V2 core delivers roughly 56 MIPS and supports JTAG/BDM for debug. The 256-MAPBGA provides generous I/O for an industrial gateway or motor-control front-end while still being hand-solderable with proper reflow profile. The internal bus architecture uses crossbar-style arbitration between the core, DMA, and peripheral bridges, allowing sustained Ethernet throughput without starving interrupt-driven code. The Flash interface includes a hardware-accelerated program/erase state machine, offloading Flash management from firmware and reducing code size overhead. Typical applications include industrial Ethernet gateways, building automation controllers, CAN-based motor nodes, remote telemetry units, and HVAC control boards. The combination of Ethernet, CAN, and 150 GPIO allows the same part to act as a master controller, removing the need for a companion bridge chip. Consider power-supply decoupling carefully - the 3.3V core and I/O rails should be bypassed with 100 nF ceramics per supply pin and bulk capacitance local to the BGA. Software should enable the watchdog early and use the DMA engine for sustained I/O to keep interrupt latency predictable. This page combines distributor pricing, same-family NXP drop-in variants, and design notes not found in the standalone user manual reference.

询价 联系我们
MCF5282CVM66 - 66MHz ColdFire V2 MCU 512KB Flash | NXP
MCF5282CVM66

MCF5282CVM66 - 66MHz ColdFire V2 MCU 512KB Flash | NXP

The NXP (Freescale) MCF5282CVM66 is a 32-bit ColdFire V2 microcontroller running at 66 MHz with 512 KB of on-chip flash memory, integrated Fast Ethernet and CAN 2.0B controllers, housed in a 256-ball MAPBGA (17x17 mm) package. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die, forming the lowest tier of the embedded processor hierarchy: MCU -> embedded processor -> system-on-chip -> microprocessor. The MCF528x family belongs to the ColdFire V2 (MCF52xx) class of 32-bit CISC-heritage embedded controllers and was specifically designed to simplify embedded Ethernet-networked MCU applications by integrating communications silicon with a rich peripheral set. Key features of the MCF5282CVM66 include the 32-bit ColdFire V2 core with Enhanced Multiply-Accumulate Unit (EMAC), 512 KB (512K x 8) of on-chip ColdFire flash module (CFM) program memory, a Fast Ethernet Controller (FEC) for 10/100 Mbps networking, a CAN 2.0B controller for industrial bus networking, an SDRAM controller, DMA controller, and a comprehensive set of serial and timing peripherals supported by a system control module with power management. Technically, the ColdFire V2 architecture provides variable-length RISC-style instruction execution with the EMAC accelerating digital signal processing operations such as filters and control loops. The integrated flash module permits in-application programming, while the SDRAM controller and external interface module (EIM) allow system memory expansion beyond the internal SRAM and flash. The interrupt controller modules and edge port module (EPORT) support responsive real-time event handling in networked industrial nodes. Typical applications include industrial Ethernet gateways and protocol converters, building automation and HVAC controllers, CAN-to-Ethernet bridging in factory automation, and networked instrumentation where a single 66 MHz MCU must run a TCP/IP stack alongside real-time control. A key design consideration is lifecycle: NXP lists this device as NRND (Not Recommended for New Designs), so it should be specified only for sustaining existing designs; new designs should evaluate current-generation MCUs. Verify flash endurance and Ethernet PHY requirements against the user manual before layout. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, verified as of 2026-10-18.

询价 联系我们
MCF5282CVM66J - 32-bit ColdFire V2 MCU, 66 MHz, 512 KB Flash | NXP
MCF5282CVM66J

MCF5282CVM66J - 32-bit ColdFire V2 MCU, 66 MHz, 512 KB Flash | NXP

The NXP Semiconductors MCF5282CVM66J is a 32-bit ColdFire V2 microcontroller (MCU) running at 66.67 MHz, integrating 512 KB of on-chip flash program memory in a 256-ball MAPBGA (17 mm x 17 mm) package. It belongs to the NXP MCF528x family and is purpose-built for embedded Ethernet- and CAN-connected industrial control applications, where deterministic real-time response and rich peripheral integration reduce board-level component count. What is a ColdFire V2 MCU? ColdFire V2 is NXP's 32-bit variable-length RISC architecture derived from the original Motorola 68000 instruction set; it retains legacy M68K source compatibility while using a simplified instruction encoding to deliver high code density and predictable interrupt latency. Within the broader semiconductor taxonomy, the MCF5282CVM66J sits as follows: ColdFire V2 core -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor device. The device is one of the original System-on-Chip (SoC) variants within the MCF5282 series and includes an integrated 10/100 Ethernet MAC, CAN 2.0B controller, EBI/EMI bus, and a feature-rich timer/PWM subsystem. Key features include 150 programmable general-purpose I/O lines, on-chip DMA, low-voltage detect (LVD), power-on reset (POR), pulse-width modulators (PWM), a watchdog timer (WDT), and a communication peripheral set covering CAN, I2C, SPI, and UART/USART. According to NXP product information, the MCF528x family is designed to simplify embedded Ethernet-networked MCU applications; this part carries that targeted feature set. The architecture combines a ColdFire V2 core with an internal crossbar bus, configurable peripheral DMA channels, and an enhanced multiply-accumulate (EMAC) unit, balancing deterministic performance with high interrupt throughput for industrial networking stacks. The 256-MAPBGA package exposes the full external bus interface for SDRAM and flash expansion, while the part operates from a 3.3 V supply with internal regulator-derived core rails. Typical applications include industrial Ethernet gateways, factory-automation PLCs, building-automation controllers, networked sensor hubs, and CAN/Ethernet bridge nodes. The combination of integrated Ethernet MAC and CAN bus makes the MCF5282CVM66J particularly well suited to plant-floor networking where a single MCU terminates both fieldbus and backhaul traffic. Designers should note that the part is NRND (Not Recommended for New Designs); for new platforms evaluate the newer MCF51CN or Kinetis E series as successors. Designers should provide adequate bulk decoupling on the BGA power balls and follow NXP's PCB layout recommendations for the 256-MAPBGA thermal pad to keep junction temperature within rated limits. This page combines current distributor pricing, drop-in cross-reference alternatives, and practical design considerations not found in the manufacturer datasheet alone.

询价 联系我们
MCF5282CVM80 - ColdFire V2 80MHz MCU 512KB Flash | NXP
MCF5282CVM80

MCF5282CVM80 - ColdFire V2 80MHz MCU 512KB Flash | NXP

The NXP MCF5282CVM80 is a 32-bit ColdFire V2 microcontroller operating at 80 MHz, integrating 512 KB of on-chip flash memory and housed in a 256-ball MAPBGA package (17x17 mm). It is part of the MCF528x family designed for embedded Ethernet-networked applications and includes an integrated Ethernet MAC, CAN controller, and a rich peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (flash/RAM), and peripherals (timers, communication interfaces, ADCs) on one die. The ColdFire V2 core is a variable-length RISC architecture derived from the original Motorola 68000 family, optimized for embedded control with deterministic interrupt response and lower power consumption than full M68k implementations. MCUs sit at the lowest tier of computing hierarchy, beneath microprocessors, application processors, and SoCs. Key features of the MCF5282CVM80 include a 32-bit ColdFire V2 core at 80 MHz core clock, 512 KB program flash with 16 KB SRAM, 10/100 Ethernet MAC with MII/RMII interface, dual CAN 2.0B controllers, three UARTs, two I2C buses, an 8-channel 10-bit ADC, 4-channel 32-bit timers, and a queued serial peripheral interface (QSPI). It supports 3.0 V to 3.6 V single-supply operation with 5 V tolerant I/O on selected pins. The MCF5282 architecture uses a Harvard-style bus with separate instruction and data paths to the on-chip flash, plus an enhanced multiply-accumulate (eMAC) unit for DSP-like operations. The integrated Ethernet and CAN peripherals make it suitable for industrial networking nodes where the MCU acts as both a protocol converter and a sensor/actuator controller. Typical applications include industrial Ethernet gateways, building automation controllers, CAN-to-Ethernet bridges, point-of-sale terminals, and motor control front-ends. The 256-ball MAPBGA package exposes the full peripheral set including external memory bus, making it well suited for designs that need to offload larger program images or data buffers to external SDRAM. When designing with this MCU, ensure the PCB uses the manufacturer-recommended 4-layer stack-up with continuous power planes under the MAPBGA, and that the 25 MHz Ethernet reference clock is routed with controlled impedance. The 512 KB flash supports in-application programming via the built-in flash controller, eliminating external boot memory. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same ColdFire V2 family, lifecycle status, and practical PCB layout guidance that goes beyond the manufacturer datasheet summary.

询价 联系我们
MCF5282CVM80J - 32-Bit ColdFire V2 MCU 512KB Flash | NXP
MCF5282CVM80J

MCF5282CVM80J - 32-Bit ColdFire V2 MCU 512KB Flash | NXP

The NXP Semiconductors MCF5282CVM80J is a 32-bit ColdFire V2 microcontroller unit (MCU) integrating 512 KB of flash memory, 64 KB of RAM, and a 10/100 Ethernet MAC in a 256-ball MAPBGA package. Operating at 80 MHz, this ColdFire V2 core variant targets embedded Ethernet-networked MCU applications that require deterministic real-time performance and rich connectivity peripherals. A ColdFire V2 microcontroller is a member of the 32-bit microcontroller family based on the Freescale/NXP ColdFire instruction set architecture, a reduced instruction set computing (RISC) derivative of the Motorola 68000 family. Positioned within the broader taxonomy, ColdFire V2 -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor, this device class simplifies embedded Ethernet-networked designs by integrating networking peripherals with general-purpose I/O, DMA, and memory interfaces on a single die. Key features include 150 general-purpose I/O lines, a ColdFire V2 core with up to 80 MHz operation, 512 KB on-chip flash program memory, 64 KB on-chip SRAM, an integrated 10/100 Mbps Ethernet MAC with Media Independent Interface (MII), two CAN 2.0B controllers, three UART/USART ports, a queued SPI module, and an I2C bus interface. Additional peripherals include DMA channels, PWM outputs, a low-voltage detect (LVD) module, a power-on reset (POR), and a watchdog timer. The architecture uses a Harvard-style memory bus with a ColdFire V2 enhanced multiply-accumulate (EMAC) unit, achieving 80 Dhrystone 2.1 MIPS at 80 MHz while maintaining code density advantages over ARM7. The MAPBGA-256 package supports high-pin-count peripheral multiplexing across external bus interfaces, EBI/EMI, and SDRAM controller signals. Typical applications include industrial Ethernet gateways, building automation controllers, point-of-sale terminals, networked sensor hubs, and CAN/Ethernet bridges. The integrated Ethernet MAC with MII allows direct connection to a PHY such as the KSZ8041, while the dual CAN controllers suit automotive and industrial Control Area Network backbones. When designing with this device, ensure the MAPBGA-256 PCB land pattern uses 1.0 mm pitch balls with proper microvia or via-in-pad construction, since high-speed Ethernet signals require controlled impedance traces. The external bus interface supports glueless connection to SDRAM and flash; adding a 32 kHz external crystal is required for the real-time clock and timing reference. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a consolidated reference for sourcing and second-sourcing decisions.

询价 联系我们
MCF53010CQT240 - 240MHz ColdFire V3 MPU, 208-TQFP | NXP
MCF53010CQT240

MCF53010CQT240 - 240MHz ColdFire V3 MPU, 208-TQFP | NXP

The NXP MCF53010CQT240 is a 32-bit ColdFire V3 microprocessor (MPU) running at 240 MHz, delivering up to 211 Dhrystone 2.1 MIPS, and housed in a 208-pin LQFP/TQFP package (28x28 mm). It is part of the MCF5301x family, combining low power consumption, high integration, and connectivity peripherals with a voice codec block, making it well suited for industrial control with embedded voice applications. A microprocessor (MPU) like the ColdFire MCF5301x is a CPU-centric integrated circuit that typically requires external memory (SRAM/SDRAM/Flash) for program and data storage. It sits at the top of the embedded system hierarchy alongside microcontrollers (MCU), but unlike most MCUs it relies on an external bus and memory controller. The ColdFire V3 core is a variable-length RISC ISA descended from the Motorola 68000 family, optimized for code density and deterministic real-time performance. Key features of the MCF53010CQT240 include an integrated Enhanced Multiply-Accumulate (EMAC) unit, 16 KBytes of unified instruction/data cache, 128 KBytes of internal SRAM, a 32-bit SDRAM/DDR controller, a 10/100 Ethernet MAC, USB 2.0 Full-Speed OTG, CAN, I2C, SPI, UARTs, and an on-chip voice codec with amplifiers. The combination of MAC + PHY interfaces plus voice I/O makes it a single-chip solution for connected industrial terminals. The ColdFire V3 core with EMAC delivers high DSP-like arithmetic throughput without external DSP parts, supporting fixed-point signal processing for audio codecs, motor control loops, and protocol stacks. Operating voltage is 3.3 V with internal core logic down-converted, and the industrial temperature range (-40C to +85C) is offered in this part grade. Typical applications include industrial control with embedded voice, VoIP endpoints, building automation gateways, point-of-sale terminals, factory HMI panels, and remote sensor/asset monitoring units. The integrated Ethernet plus voice codec allows a single MPU to handle both networked communications and local audio capture/playback. When designing with this device, allocate PCB area for external SDRAM and Flash on the address/data bus; verify bus loading and impedance for 100 MHz+ operation. Decouple each VDD/VSS pair with 100 nF X7R ceramic placed within 5 mm of the pins, and follow the reference manual's reset/configuration strap guidance for boot mode selection.

询价 联系我们
MCF53011CQT240 - ColdFire V3 MPU, 240MHz, 208-TQFP | NXP
MCF53011CQT240

MCF53011CQT240 - ColdFire V3 MPU, 240MHz, 208-TQFP | NXP

The NXP MCF53011CQT240 is a 32-bit ColdFire V3 microprocessor unit (MPU) operating at up to 240 MHz, housed in a 208-pin TQFP (28x28 mm) package. It integrates a Version 3 ColdFire core with EMAC delivering up to 211 Dhrystone 2.1 MIPS, a 16 KByte unified instruction/data cache, 128 KBytes of internal SRAM, and a ROMless external memory interface. The device is fabricated in a low-power CMOS process and is targeted at industrial control with embedded voice applications. What is a ColdFire microprocessor? A ColdFire microprocessor is a 32-bit RISC-style processor architecture originally derived from the Motorola 68000 family, designed by NXP (formerly Freescale) for cost-sensitive, low-power embedded applications. Positioned in the taxonomy as: microprocessor (MPU) > 32-bit MPU > ColdFire family > ColdFire V3 core > semiconductor, ColdFire V3 parts combine moderate computational performance with low power consumption and rich peripheral integration, making them well suited to industrial control, point-of-sale, and embedded audio applications. Key features of the MCF53011CQT240 include a fast Ethernet MAC (EMAC) with MII/RMII interface for industrial networking, USB 2.0 Full-Speed and Host/Device On-the-Go (OTG) controllers, a voice codec interface with multiple time-division-multiplexed (TDM) channels, CAN 2.0B controller for industrial fieldbus connectivity, and a peripheral set covering UARTs, I2C, SPI, and GPIOs. The integrated eSDHC and external bus interface support NAND flash, SDRAM, and SRAM memory expansion. Architecturally, the ColdFire V3 core uses a variable-length instruction pipeline and Harvard-style split cache for instruction and data, allowing deterministic interrupt latency that is critical in real-time control loops. The dual-issue capabilities and dedicated multiply/accumulate (MAC) hardware accelerate DSP-style signal processing required by the integrated voice codec engine. Typical applications include industrial control with embedded voice (intercom, public-address, and VoIP-style appliances), human-machine interface (HMI) terminals, point-of-sale terminals with audio feedback, factory automation PLCs with Ethernet connectivity, and medical/automation equipment requiring multi-protocol industrial networking. The combination of CAN + Ethernet + USB + voice codec removes several external ICs from a typical BOM, reducing board area and cost in compact embedded designs. When designing with the MCF53011CQT240, follow the manufacturer reference design for power-rail decoupling and external bus termination. Place at least four 0.1 uF decoupling capacitors near each power pin, route the 50 MHz system clock with controlled impedance, and ensure the SDRAM traces are length-matched to the data strobe signals. The TQFP-208 package requires multilayer PCB stack-up for high-speed signal integrity. This page synthesizes distributor pricing, pin-compatible drop-in alternatives within the MCF5301x family, and practical PCB and firmware design notes not consolidated in a single place in the manufacturer datasheet.

询价 联系我们
MCF53012CQT240 - 32-Bit 240MHz ROMless MCU | NXP
MCF53012CQT240

MCF53012CQT240 - 32-Bit 240MHz ROMless MCU | NXP

The NXP Semiconductors MCF53012CQT240 is a 32-bit, 240 MHz ColdFire V3 ROMless microcontroller in a 208-pin TQFP package measuring 28 mm by 28 mm. It belongs to the MCF5301x family and is designed for embedded systems requiring high-performance control, Ethernet connectivity, USB OTG, serial interfaces, and programmable peripherals. The verified listing identifies its core processor as ColdFire V3, core size as 32-bit, speed as 240 MHz, and program memory as ROMless. A microcontroller is a semiconductor device that integrates a processor core, memory interfaces, communication peripherals, timers, interrupt control, and I/O into one integrated circuit. In the product hierarchy, this device is a 32-bit embedded microcontroller, part of the broader semiconductor and embedded-processing categories. Its ROMless architecture requires an external boot or program-memory solution, making the part suitable for systems where firmware storage, code execution, or product configuration must be external. The MCF53012CQT240 provides connectivity identified in the verified data as EBI/EMI, Ethernet, I2C, memory card, SPI, SSI, UART/USART, and USB OTG. The listed peripherals include DMA, PWM, and WDT. These resources support designs involving network-connected embedded equipment, industrial control, communications gateways, data acquisition, and peripheral control. The verified product description reports 61 I/O, while the listed package has 208 terminals. The device is identified as obsolete in the verified manufacturer-related listing, so lifecycle planning should account for long-term sourcing and design migration. Because this page uses only supplied verified data, details such as supply voltage, memory sizes, electrical limits, temperature range, pin names, and detailed package dimensions beyond the stated 28 mm by 28 mm are not inferred. Use the manufacturer datasheet and package drawings for schematic capture, decoupling, clocking, boot configuration, and PCB layout decisions. Typical engineering use includes industrial automation, Ethernet-connected controllers, USB-enabled embedded systems, serial bridges, memory-card interfaces, and real-time peripheral control. The 240 MHz ColdFire V3 core provides the processing headroom for control logic and communication stacks, while DMA and PWM support efficient data movement and timing-sensitive output generation. Its large 208-pin package exposes extensive external connectivity but requires careful escape routing and multilayer PCB design. A key design consideration is that the ROMless device depends on external program memory or a suitable boot arrangement. Confirm memory-interface compatibility, boot configuration, power sequencing, clock sources, peripheral pin multiplexing, and external transceiver requirements before layout release. Do not assume pin compatibility or drop-in replacement status without checking the exact package and datasheet. This page synthesizes the verified product identity, connectivity, package, lifecycle, sourcing links, and selection considerations available for MCF53012CQT240. It separates verified facts from unavailable parameters and avoids inventing electrical or pin-level details that are not present in the supplied data.

询价 联系我们
MCF53013CQT240 - 240MHz ColdFire V3 MPU | NXP | TQFP-208
MCF53013CQT240

MCF53013CQT240 - 240MHz ColdFire V3 MPU | NXP | TQFP-208

The NXP Semiconductors MCF53013CQT240 is a 32-bit ColdFire Version 3 microprocessor with EMAC, operating at 240 MHz in a 208-pin LQFP package. It is ROMless, uses a 28 mm by 28 mm package, and is identified by distributor data as the MCF5301x family part suited to embedded voice, networking, and industrial control designs. A microprocessor is the central processing element of an embedded system. It executes instructions, controls memory and peripherals, and connects external hardware through dedicated interfaces. The MCF5301x family combines the ColdFire processor core with connectivity peripherals and, according to the available part description, a voice codec and amplifiers. This places it above a basic microcontroller in the product hierarchy: microprocessor, embedded processor, semiconductor, and power-management-dependent system component. Key verified features include a Version 3 ColdFire core, EMAC support, 240 MHz operation, 211 Dhrystone 2.1 MIPS performance, a 16 Kbyte unified instruction/data cache, and 128 Kbytes of additional memory described in the available data. The ROMless designation means external program memory is required, which allows deployment-specific firmware to be selected while keeping the processor package independent of fixed embedded software. The device is also identified as a ColdFire V3 MCF5301x part with integrated voice-oriented functions. The MCF53013CQT240 is therefore relevant to voice-over-IP gateways, embedded telephony equipment, networked control systems, and industrial communication products where a higher-performance processor and multiple interfaces are useful. The 208-pin LQFP provides the package pin count required for the device's integrated peripherals. Because the exact pin names, memory-map details, electrical limits, and peripheral assignments were not included in the supplied verified data, this page does not infer them. The manufacturer datasheet should be consulted for authoritative pinout, voltage limits, clock requirements, decoupling, and application schematics before hardware is released to production. For sourcing and lifecycle decisions, the available distributor records should be treated as time-sensitive. The supplied search snapshot was fetched on 2026-10-20, while one distributor listing reports a reference quantity and price. Inventory, lifecycle status, exact package markings, and delivery commitments must be reconfirmed with the authorized supplier before ordering. This page combines verified distributor product data, ColdFire family details, application context, sourcing constraints, and explicit engineering gaps so engineers can distinguish documented facts from information that still requires datasheet validation.

询价 联系我们
MCF53014CMJ240 - ColdFire V3 MCU 240MHz, 256-MAPBGA | NXP
MCF53014CMJ240

MCF53014CMJ240 - ColdFire V3 MCU 240MHz, 256-MAPBGA | NXP

The NXP (formerly Freescale) MCF53014CMJ240 is a 32-bit ColdFire V3 microprocessor unit operating at 240 MHz, packaged in a 256-ball MAPBGA (17 mm x 17 mm) plastic RoHS-compliant housing. The device delivers up to 211 Dhrystone 2.1 MIPS at the rated clock and integrates 16 KBytes of unified instruction/data cache alongside 128 KBytes of internal SRAM with standby power support. It is designed for industrial-grade embedded applications combining deterministic control with on-chip connectivity. A microprocessor (MPU) is the highest-level processing element in an embedded system, executing application code, handling interrupts, and coordinating peripherals. The MCF53014CMJ240 belongs to the ColdFire family, a scalable 68k-derived architecture from NXP optimized for low-power, high-integration designs, sitting architecturally between 8-bit microcontrollers and full application processors. It includes an integrated 10/100 Ethernet MAC (EMAC), USB OTG, and other connectivity peripherals. Key features of the MCF53014CMJ240 include 240 MHz ColdFire V3 core performance, 16 KB unified L1 cache, 128 KB internal SRAM with standby power support, 10/100 Ethernet MAC for networked industrial control, USB OTG host/device capability, ROMless boot from external flash, integrated crossbar switch, and an industrial -40C to +85C operating temperature range. The integrated peripherals reduce board complexity and BOM cost while supporting common industrial connectivity standards. The ColdFire V3 architecture uses a variable-length instruction set with both A- and B-line ColdFire ISA features, an enhanced MAC module for DSP-style operations, and a Harvard-style cache structure that delivers high code density while retaining deterministic interrupt response. The 128 KB SRAM is partitioned for low-leakage standby retention, allowing fast context save/restore in power-managed designs without external memory accesses. A bus crossbar arbitrates concurrent transfers between the core, EMAC, USB, and DMA, eliminating single-master bottlenecks. Typical applications include industrial control with embedded voice/audio processing, networked sensor gateways, factory automation controllers, embedded HMI front-ends, and remote monitoring/telemetry devices. The on-chip Ethernet MAC and USB OTG make it well suited for IP-connected industrial nodes where deterministic control and local diagnostics coexist on the same board. When designing with the MCF53014CMJ240, plan for an external boot flash (ROMless), supply decoupling per the Freescale/NXP reference design, and careful 256-ball BGA fan-out for PCB escape. JTAG/BDM is required for in-system debug and boundary scan. This page synthesizes distributor pricing, drop-in compatible ColdFire V3 alternatives in the same 256-ball MAPBGA, and practical design notes not found in the standalone datasheet.

询价 联系我们
MCF53014CMJ240J - 240MHz ColdFire V3 32-Bit MPU | NXP
MCF53014CMJ240J

MCF53014CMJ240J - 240MHz ColdFire V3 32-Bit MPU | NXP

The NXP Semiconductors MCF53014CMJ240J is a 32-bit ColdFire V3 microprocessor operating at 240 MHz, integrating Ethernet and voice-codec connectivity for industrial embedded control. It is packaged as a 256-ball MAPBGA measuring 17 mm by 17 mm and is identified as a ROMless part. The verified source data lists 83 I/O, 128 KB internal SRAM, a 16 KB unified instruction/data cache, and connectivity including EBI/EMI, Ethernet, I2C, memory card, SPI, SSI, UART/USART, USB, and USB OTG. A microprocessor such as the MCF53014 is a higher-level computing device than a microcontroller: it executes an instruction set, manages memory, coordinates peripherals, and supports embedded operating systems or real-time control software. The ColdFire V3 architecture combines that general-purpose processing role with integrated connectivity, allowing an industrial controller to handle networking and embedded voice functions without requiring separate interface devices. Its 240 MHz operating frequency provides a concrete performance point for control-loop, communications, and human-interface workloads. Verified features include Version 3 ColdFire processing with EMAC, 211 Dhrystone 2.1 MIPS at 240 MHz, a 16 KB unified instruction/data cache, and 128 KB internal SRAM. The internal SRAM includes standby power-supply support, while the peripheral mix includes DMA, PWM, and a watchdog timer. The processor is a ROMless device, so production designs must provide external nonvolatile boot storage rather than relying on integrated program memory. The 256-MAPBGA package and industrial temperature grade position the device for embedded industrial-control platforms rather than general commercial hobby use. Its external bus and serial interfaces support connections to memory, storage, audio circuitry, communications equipment, and human-interface modules. The Ethernet MAC and USB connectivity are especially relevant to gateways, terminals, and voice-enabled industrial equipment, while the watchdog and DMA resources support reliable real-time system behavior. A primary design consideration is package complexity. A 256-ball BGA requires careful PCB escape routing, via-in-pad or via-under-bump strategies where required, controlled impedance, adequate power-plane integrity, and assembly-process validation. Designers should also verify external memory support, boot-memory requirements, pin multiplexing, and power sequencing against the manufacturer data sheet before layout release. The verified sources identify the package as 17 mm by 17 mm MAPBGA-256, but the complete public pinout was not included in the supplied evidence.

询价 联系我们