المنتجات (46,000+)

MAX3488ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488ESA+T

MAX3488ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3488ESA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, supporting data rates up to 10Mbps. The device is supplied in an 8-SOIC package measuring 0.154 inches wide and 3.90mm long, with MAX3488ESA+T configurations offered in tape-and-reel packaging. Its slew-rate-limited transmitter is designed to reduce electromagnetic interference and cable reflections while maintaining reliable balanced-data communication. An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals into differential bus levels and receives differential bus signals back into logic-level outputs. The MAX3488 belongs to the RS-485 transceiver hierarchy, which also includes half-duplex and full-duplex bus interface devices used in industrial automation, communications equipment, instrumentation, and embedded control systems. RS-422 commonly supports point-to-point links, while RS-485 allows multiple nodes on a shared bus. Key verified features include a 3V to 3.6V supply range, one transmitter and one receiver, support for both RS-422 and RS-485 protocols, and operation at data rates up to 10Mbps. The slew-rate-limited driver is specifically intended to minimize EMI and reduce reflections caused by improperly terminated cables. An extended variant identified as MAX3488E is listed with ±15kV ESD protection and a 12Mbps maximum data rate, but those extended ratings should not be assumed for the ESA suffix without confirmation from the manufacturer. The MAX3488 family combines low-power 3.3V operation with a differential bus interface. The verified distributor data identifies MAX3488ESA+ as a full RS-422/RS-485 transceiver in an 8-SOIC package. Different family members provide distinct combinations of operating speed, supply range, and full-duplex versus half-duplex behavior, so an engineer should compare pin functions and electrical limits rather than relying only on the family name when making a drop-in substitution. Typical applications include industrial RS-485 links, factory automation controllers, building-control equipment, instrumentation gateways, and embedded serial communications modules. In these systems, the transceiver can interface a microcontroller UART to a balanced bus while the slew-rate-limited output helps control edge-rate-induced EMI. Board design must still provide correct bus topology, termination, grounding, and protection appropriate to the installation environment. A key design consideration is that the MAX3488ESA+T operates from a 3V to 3.6V supply, so its logic levels and interface limits must be compatible with the connected processor. Designers should also distinguish the standard MAX3488 from the MAX3488E extended product because the verified source lists different maximum speeds and ESD protection levels. Tape-and-reel notation identifies the shipping format and should not be treated as a functional difference. This product page combines verified manufacturer and distributor information, packaging details, source-backed technical facts, drop-in replacement analysis, and practical RS-485 design guidance. It also distinguishes confirmed values from parameters that require confirmation from the complete manufacturer datasheet, helping engineers avoid unsupported assumptions during schematic capture and PCB layout.

طلب عرض سعر اتصل بنا
MAX3490AEGSA+ - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490AEGSA+

MAX3490AEGSA+ - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490AEGSA+ is a 3.3V-powered, full-duplex RS-485/RS-422 transceiver rated for data rates up to 20Mbps, with ±20kV ESD protection in an 8-pin SOIC package. It combines one driver and one receiver for bidirectional point-to-point communication over long cables, including industrial control links, instrumentation, and noisy industrial environments. The low-voltage supply and slew-rate-limited operation make it suitable for systems using modern low-voltage logic and requiring controlled edge rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential cable signals and receives differential cable signals back into digital logic. The MAX3490AEGSA+ operates in the voltage-regulator hierarchy of industrial communications: it sits between a host controller, such as a UART or processor, and a physical RS-485 or RS-422 cable. Differential signaling improves noise immunity over longer cable runs and allows reliable communication between separated equipment. The MAX3490AEGSA+ family is designed for 3.3V operation and provides 20Mbps maximum data rate with slew-rate-limited drivers. The ±20kV ESD protection helps improve robustness when cables are exposed to electrostatic discharge during installation or operation. Its full-duplex configuration provides separate transmit and receive paths, which is useful when the design requires continuous communication in both directions rather than a shared half-duplex bus. The device is supplied in an 8-pin SOIC package, allowing direct assembly into conventional surface-mount PCB layouts. The MAX3490AEGSA+ family is identified by Analog Devices as a production 3.3V-powered, slew-rate-limited, true RS-485/RS-422 transceiver. The related MAX3490AE page lists a 10Mbps product family overview, while the MAX3490AEGSA+ listing identifies the 20Mbps-rated version. Typical applications include industrial PLC-to-PLC links, factory-floor data acquisition, building automation, security equipment, and embedded instrumentation. When designing the interface, provide correct termination, biasing, common-mode protection, and cable routing according to the system topology. The differential pair should be routed as a controlled-impedance pair, with protection and ground-return arrangements evaluated for the installation environment. This page combines the manufacturer product information with distributor listings and application-oriented engineering guidance. It also organizes the device's RS-485/RS-422 role, electrical limits, package details, replacement considerations, and practical layout practices into a concise selection reference for engineers.

طلب عرض سعر اتصل بنا
MAX3490AEGSA+T - 20Mbps RS-485/RS-422 Transceiver | ADI
MAX3490AEGSA+T

MAX3490AEGSA+T - 20Mbps RS-485/RS-422 Transceiver | ADI

The Analog Devices MAX3490AEGSA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 20Mbps, and ±20kV ESD protection, housed in an 8-pin SOIC package. Its slew-rate-limited driver reduces EMI and cable reflections, while true RS-485/RS-422 operation supports robust point-to-point and multidrop communications. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts received differential signals back into digital logic. The differential signaling provides common-mode rejection and noise immunity, making these transceivers useful for industrial control, telecommunications, instrumentation, and data links operating over longer cables than single-ended interfaces. The MAX3490AEGSA+T combines a 3.3V supply with a 20Mbps maximum signaling rate. Its slew-rate-limited output reduces high-frequency harmonics and ringing, which can improve interoperability in systems where cable length, connectors, or imperfect termination create reflections. Integrated ±20kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or handling. Each device contains one transmitter and one receiver, allowing one half-duplex bus node to drive a differential line and receive the corresponding differential bus state. The 8-pin SOIC package supports conventional surface-mount assembly while reducing board area compared with larger transceiver packages. The +T suffix identifies the tape-and-reel ordering form for production handling. Typical uses include industrial-control networks, building automation equipment, telecommunications interfaces, instrumentation links, and EMI-sensitive RS-422 connections. Designers should match the bus topology, cable impedance, termination method, grounding strategy, and logic-level supply requirements before finalizing the system interface. Place the transceiver close to the connector and route the differential pair as a controlled-impedance pair. Keep the driver and receiver grounds consistent with the interface reference plane, and use the manufacturer pin description and application guidance when assigning PCB tracks. The slew-rate-limited output should be evaluated together with maximum cable length and system data rate. This page organizes the manufacturer specifications, interface requirements, comparison points, and practical PCB guidance needed to evaluate the MAX3490AEGSA+T as a 3.3V, 20Mbps RS-485/RS-422 transceiver.

طلب عرض سعر اتصل بنا
MAX3490CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3490CPA+

MAX3490CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3490CPA+ is a 3.3V-powered, 10Mbps, slew-rate-limited true RS-485/RS-422 transceiver with one driver and one receiver, supplied in an 8-pin PDIP package. It is designed for point-to-point and multidrop industrial data links where low-voltage digital systems must communicate over longer, noise-prone cabling. The verified product data identifies full RS-422 and RS-485 operation, a 1/1 transceiver configuration, and a maximum data rate of 10Mbps. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals and back again. Differential signaling improves common-mode noise immunity and allows reliable communication over cables where single-ended logic signals would be more susceptible to interference. The MAX3490CPA+ belongs to the transceiver hierarchy: interface transceiver, RS-485/RS-422 interface, wired-communication semiconductor, and signal-conditioning component. The MAX3490 family includes one driver and one receiver, allowing a node to both transmit and receive data. Its 3.3V operation supports systems powered from modern low-voltage rails, while slew-rate limiting reduces unwanted transmit-edge energy and helps control electromagnetic emissions. The device is also described as a true RS-485/RS-422 interface solution, making it suitable for industrial controls, instrumentation links, and communications equipment. The MAX3490CPA+ is a through-hole PDIP-8 device, which is useful when a design needs socketed assembly, prototype flexibility, or a leaded package rather than a surface-mount footprint. The verified distributor listings identify the package as 8-PDIP or DIP-8, with a 0.300-inch, 7.62mm body. The exact pin assignments, electrical limits, temperature range, termination requirements, and recommended operating conditions should be confirmed in the manufacturer datasheet before layout or production release. Typical applications include industrial RS-485 buses, data acquisition systems, remote sensor interfaces, RS-422 point-to-point links, embedded control networks, and communications equipment operating from a 3.3V rail. In a practical bus, the transceiver connects a controller UART to a twisted-pair network, while external termination and biasing may be required according to the bus topology and system requirements. Keep the differential trace pair short, matched, and away from noisy switching paths. This product page consolidates verified distributor and manufacturer information, current sourcing links, and design context for the MAX3490CPA+. Pricing, availability, lifecycle details, and detailed electrical parameters should be refreshed at the source before purchase because distributor data changes over time.

طلب عرض سعر اتصل بنا
MAX3490CSA+ - 3.3V 10Mbps RS-422/RS-485 | Analog Devices
MAX3490CSA+

MAX3490CSA+ - 3.3V 10Mbps RS-422/RS-485 | Analog Devices

The Analog Devices MAX3490CSA+ is a 3.3V-powered, 10Mbps RS-422/RS-485 interface transceiver in an 8-pin SOIC package. It combines one driver and one receiver for bidirectional differential data links and supports the low-voltage supply range stated in the manufacturer datasheet. The MAX3490 family is intended for industrial, instrumentation, and embedded communication systems where a compact differential interface is required. An RS-422/RS-485 transceiver is an interface IC that converts between logic-level digital signals and balanced differential signals on a communication bus. RS-422 commonly supports point-to-point, full-duplex links, while RS-485 commonly supports multipoint, half-duplex networks. The MAX3490 combines both interface standards in one device, with separate driver and receiver sections and direction control handled by the host logic. The MAX3490CSA+ is identified as a 3.3V-powered, 10Mbps, slew-rate-limited, true RS-485/RS-422 transceiver. Its low-power 3.3V operation suits modern controller platforms and reduces supply demand compared with legacy 5V interface designs. The 10Mbps capability makes it relevant for factory equipment, data acquisition, industrial controllers, and other systems requiring a higher-speed differential serial interface. The device uses one driver and one receiver, allowing a compact implementation of a full-duplex RS-422 connection or a half-duplex RS-485 connection with external direction control. Differential signaling improves noise immunity over single-ended links and helps support reliable communication over longer cables when the bus is properly terminated and laid out. For RS-485 networks, place termination resistors at the physical ends of the bus, bias the idle differential state appropriately, and keep transceiver stub branches short. For RS-422 links, use the receiver and driver pins associated with the intended full-duplex topology and confirm the manufacturer pin configuration before PCB release. Designers should verify supply voltage, driver enable polarity, receiver enable polarity, common-mode limits, cable length, termination, and transceiver direction timing against the MAX3490 datasheet. This page combines verified manufacturer and distributor information, commercial sourcing context, and practical interface-design guidance for evaluating the MAX3490CSA+.

طلب عرض سعر اتصل بنا
MAX3490CSA+T 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490CSA+T

MAX3490CSA+T 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490CSA+T is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 10Mbps in an 8-pin SOIC package. Its low-power architecture is designed for industrial communication links where a compact interface is required for bidirectional serial data. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and converts received differential signals back into logic levels. RS-485 supports multipoint buses with bidirectional communication, while RS-422 provides a point-to-point differential link. The MAX3490CSA+T belongs to the interface IC family within the broader semiconductor and industrial-control hierarchy. Key features include operation from a 3.0V to 3.6V supply, a maximum data rate of 10Mbps, one driver and one receiver, and slew-rate-limited operation for reduced EMI and reflection control. The device also includes short-circuit protection and thermal shutdown according to the manufacturer product information. Its 8-SOIC package supports conventional surface-mount PCB assembly. The MAX3490CSA+T uses true differential RS-485/RS-422 signaling, allowing communication over longer cable runs than single-ended interfaces while improving noise immunity. The receiver supports fail-safe operation when the bus is idle, and the driver places its output in a high-impedance state during thermal shutdown. These characteristics suit industrial controllers, instrumentation, data acquisition systems, and factory automation equipment. Typical applications include industrial sensor networks, RS-485 motor-control links, building automation equipment, test and measurement instruments, and embedded control systems. The 3.3V supply is convenient for systems built around modern low-voltage processors, while the 10Mbps capability supports higher-speed factory and data-acquisition links. For PCB design, place the transceiver close to the connector and route the balanced differential pair as a controlled-impedance pair. Connect the bus termination and biasing components according to the system topology, and keep the ground reference continuous between the transceiver and cable interface. Verify the supply voltage, idle-bus behavior, and cable length before releasing the design. This product page combines the manufacturer’s MAX3490 technical information with practical selection guidance, application positioning, and package-level design considerations. It is intended to help engineers identify the correct transceiver for low-voltage, high-speed RS-485 and RS-422 interfaces without conflating protocol requirements, electrical termination, and PCB layout decisions.

طلب عرض سعر اتصل بنا
MAX3490ECPA - 12Mbps RS-485 Transceiver | Maxim Integrated
MAX3490ECPA

MAX3490ECPA - 12Mbps RS-485 Transceiver | Maxim Integrated

The Maxim Integrated MAX3490ECPA is a 3.3 V-powered, ±15 kV ESD-protected RS-485/RS-422 transceiver that supports data rates up to 12 Mbps and uses an 8-pin PDIP package. The device combines one driver and one receiver in a single package, with slew-rate-limited operation intended to reduce unwanted signal transitions on unbalanced communication lines. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts received differential voltages back into digital logic. The MAX3490ECPA belongs to the MAX3483E family of low-power transceivers designed for industrial, instrumentation, and data-communication links where both long-distance noise immunity and compact integration are important. The principal operating characteristics include a 3.3 V supply, ±15 kV ESD protection, operation at up to 12 Mbps, and slew-rate-limited true RS-485/RS-422 operation. Its one-driver/one-receiver configuration supports point-to-point and multidrop network arrangements when the bus topology, termination, and grounding strategy are designed correctly. The 8-pin PDIP package also supports conventional through-hole PCB assembly and prototyping. Slew-rate limiting reduces the rate at which the differential driver changes state, limiting high-frequency energy that can couple into adjacent circuitry. This behavior is particularly useful on long cables or in systems where reducing edge-related ringing and crosstalk is more important than maximizing data rate. The device should still be evaluated with the intended cable length, topology, termination network, and grounding arrangement. Typical applications include industrial control networks, instrumentation links, data acquisition systems, building automation equipment, and point-to-point data communications. The MAX3490ECPA is appropriate when the system uses 3.3 V logic, requires integrated transmit and receive functions, and can tolerate the operating-speed limitations of a through-hole PDIP package. For a new design, confirm the exact driver-enable and receiver-enable polarity, supply decoupling, bus termination, and fail-safe behavior against the manufacturer pin description and datasheet before fabrication. Place the device near the bus connector when practical to minimize unprotected trace length and reduce ESD exposure. This product record combines the manufacturer’s family-level functional information, package details, operating characteristics, and practical interface design guidance. It also provides drop-in family alternatives, comparison parameters, and application-focused engineering context to support component selection before schematic capture.

طلب عرض سعر اتصل بنا
MAX3490ECSA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490ECSA+T

MAX3490ECSA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3490ECSA+T is a 3.3 V powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, and ±15 kV ESD protection in an 8-pin SOIC package. The integrated slew-rate-limited driver reduces unwanted ringing and electromagnetic interference on long, point-to-point communication links. An RS-485/RS-422 transceiver is an interface IC that converts between CMOS/TTL logic levels and balanced differential signals. It belongs to the transceiver hierarchy within interface ICs, where differential signaling improves noise immunity and allows reliable communication over longer cable distances than ordinary single-ended logic. The MAX3490E family combines low-power 3.3 V operation, fault-tolerant differential drivers, and enhanced electrostatic-discharge protection for industrial and instrumentation networks. Key features include operation from a single 3.3 V supply, a 12 Mbps maximum signaling rate, ±15 kV ESD protection on the bus pins, and one transmit and one receive channel per device. The partially slew-rate-limited driver helps control edge rates, reducing reflections and radiated emissions on suitable terminated networks. The receiver provides differential input detection for RS-422 links, while the device can also participate in half-duplex RS-485 networks when its direction-control interface is used correctly. The MAX3490E series belongs to the MAX3483E family of low-power transceivers. Its internal architecture combines a differential line driver, a differential receiver, bus-direction logic, and protection structures within one compact package. This integration reduces the number of discrete components required for isolated or non-isolated industrial links while preserving a standardized differential bus interface. Designers must still provide appropriate termination, biasing, protection, and grounding for the selected RS-422 or RS-485 topology. Typical uses include industrial sensor networks, programmable logic controller communication, building-automation equipment, test and measurement instruments, data-acquisition modules, and embedded serial links. It is particularly useful when a compact PCB area, 3.3 V supply, moderate-to-high data rates, and direct-contact ESD robustness are required. The 8-pin SOIC footprint also simplifies assembly in designs already using surface-mount interface components. Design considerations include placing the transceiver close to the connector, maintaining a continuous ground reference between the logic side and the cable interface, and using the termination method appropriate to the topology. Differential pairs should be routed with consistent geometry, while surge or isolation components may be required when the cable leaves the protected enclosure. Verify signal polarity, driver-enable logic, receiver output levels, and supply sequencing before releasing a new PCB. This page combines the manufacturer's product specifications, package and interface guidance, comparison criteria, and practical PCB considerations to support faster engineering evaluation of the MAX3490ECSA+T in industrial communications designs.

طلب عرض سعر اتصل بنا
MAX3490EEPA+ - 12Mbps RS-485 Transceiver | Analog Devices
MAX3490EEPA+

MAX3490EEPA+ - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3490EEPA+ is a 3.3 V-powered, slew-rate-limited RS-485/RS-422 transceiver with a maximum data rate of 12 Mbps and ±15 kV ESD protection, packaged in an 8-pin PDIP. It is designed for industrial, instrumentation, communications, and data-acquisition systems that require a true differential transceiver rather than a single-ended RS-232 interface. An RS-485 transceiver is an interface IC that combines a differential line driver with a differential receiver, allowing information to be transmitted reliably over longer cable runs than a single-ended interface. The MAX3490EEPA+ belongs to the broader hierarchy of interface ICs, communication transceivers, physical-layer devices, and semiconductors. Its differential signaling supports noise-resistant communication between equipment located at different ground potentials. The principal operating characteristics are a 3.3 V supply, a 12 Mbps maximum data rate, ±15 kV ESD protection, and slew-rate-limited outputs. The 12 Mbps capability permits the device to handle high-speed command, control, data, and instrumentation links. Slew-rate limiting reduces the high-frequency content of driver transitions, which helps limit electromagnetic interference and reduces the potential for reflections and data errors on suitable bus layouts. This device supports both RS-485 and RS-422 communication modes. RS-485 is commonly used for multidrop buses connecting multiple nodes, while RS-422 is commonly used for point-to-point or limited-driver configurations. The MAX3490EEPA+ combines these functions in one transceiver package, allowing the same physical interface circuit to be configured according to the system’s grounding and bus topology. Typical uses include industrial control systems, test and measurement equipment, building automation, data-acquisition units, motor-control systems, and industrial communications adapters. The 8-pin PDIP package is also convenient for prototyping and systems assembled through through-hole insertion rather than surface-mount automation. PCB implementation should preserve the transceiver’s high-speed signal integrity. Route the differential bus as a closely coupled pair, terminate the line at appropriate physical endpoints, and avoid adding unnecessary stubs. Place the transceiver close to the connector and keep ground returns short. The manufacturer datasheet remains the controlling reference for pin assignments, supply decoupling, driver enable behavior, receiver enable behavior, and absolute maximum ratings. This product page combines the exact manufacturer and distributor identifiers, separates functionally useful alternatives by package and data rate, and adds implementation guidance for evaluating the MAX3490EEPA+ in a new RS-485 or RS-422 design.

طلب عرض سعر اتصل بنا
MAX3490EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490EESA+

MAX3490EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490EESA+ is a 3.3 V, single-channel RS-485/RS-422 transceiver with one driver, one receiver, 12 Mbps maximum data rate, and ±15 kV ESD protection in an 8-pin SOIC package. Its slew-rate-limited driver supports reliable point-to-point and multidrop industrial communication while helping reduce cable reflections and electromagnetic interference. The MAX3490EESA+ is identified as a production part by the manufacturer. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and converts received differential signals back into logic levels. It belongs to the communication-interface hierarchy: transceiver → RS-485/RS-422 interface IC → interface IC → integrated circuit. These transceivers are designed for longer-distance, noise-resistant data links than single-ended interfaces, making them suitable for industrial equipment, building controls, instrumentation, and long cable runs. The MAX3490EESA+ combines 12 Mbps operation with 3.3 V power operation. Its one-driver, one-receiver arrangement allows a node to transmit and receive data, although the driver and receiver enable functions determine the operating direction. The manufacturer describes the MAX3490E family as slew-rate-limited, true RS-485/RS-422 devices with ±15 kV ESD protection. The 8-pin SOIC package supports compact surface-mount layouts while exposing the standard transceiver functions needed for balanced bus implementations. At the system level, the MAX3490EESA+ bridges a host controller or programmable logic and a differential communication bus. The receiver evaluates the difference between the two bus conductors, providing common-mode rejection for a noise-affected industrial environment. The differential bus also enables ground-potential differences between connected equipment to be tolerated within the interface's specified operating limits. The exact common-mode range, receiver thresholds, and electrical limits must be confirmed in the manufacturer datasheet before final sign-off. Typical uses include industrial control links, factory automation equipment, building-automation nodes, test and measurement systems, and embedded data acquisition. The 12 Mbps capability is useful when a design must transfer short, high-volume data bursts over a modest cable distance rather than operate as a slow long-distance field bus. The part can also pair with isolation or interface components when a design requires galvanic separation, surge protection, or additional bus transceivers. Designers should verify the differential-impedance-controlled trace and cable geometry, provide the bus termination specified by the system architecture, and connect the transceiver reference or common-mode network according to the manufacturer application guidance. Placement near the connector can reduce exposure of sensitive receive paths to radiated and conducted noise. Decoupling should also follow the datasheet recommendations, while ESD protection should be evaluated at the connector rather than assumed to replace an external protection network. This product page consolidates the verified manufacturer, distributor, and cross-reference information with practical selection guidance, packaging details, interface comparisons, and application notes. It is intended to help engineers identify the correct 8-SOIC transceiver while separating documented parameters from values that still require datasheet confirmation.

طلب عرض سعر اتصل بنا
MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices
MAX3490EESA+T

MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3490EESA+T is a 3.3V-powered, single-channel RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 12Mbps in an 8-pin SOIC package. The MAX3490E combines true RS-485 and RS-422 operation with slew-rate-limited signaling and ±15kV ESD protection, making it appropriate for industrial communication links where both high throughput and surge robustness are required. An RS-485/RS-422 transceiver is a physical-layer interface integrated circuit that converts logic-level signals into balanced differential bus voltages and converts incoming differential signals back into digital logic. The differential signaling improves common-mode noise immunity and allows reliable data transmission over longer cable runs. Positioned within the hierarchy of interface ICs, communications transceivers, and data-bus interface devices, the MAX3490E supports point-to-point RS-422 links as well as multi-drop RS-485 networks when the bus topology, termination, and biasing are designed correctly. Principal features include a 3.3V supply, a maximum data rate of 12Mbps, ±15kV ESD protection, and slew-rate-limited driver outputs. The EESA variant provides an extended -40°C to +85°C operating range, while the +T suffix identifies the tape-and-reel ordering option. The device also includes a receiver with a fail-safe bias network, which helps determine a defined logic state when the bus is idle, disconnected, or shorted. The MAX3490E architecture uses a differential driver and a differential receiver in one package, reducing board area compared with separate driver and receiver ICs. Slew-rate limiting reduces high-frequency EMI and helps suppress reflections on imperfectly terminated cables. Because the device supports both RS-485 and RS-422 standards, one transceiver can cover point-to-point industrial links, multidrop buses, motor-control networks, and data-acquisition equipment when the appropriate termination and idle-bias components are installed. Typical applications include industrial PLC and factory-automation links, instrumentation buses, motor-driver control interfaces, building-automation equipment, and embedded data-acquisition systems. The 12Mbps capability supports demanding factory and motor-control traffic, while the 3.3V supply simplifies interfacing with modern low-voltage controllers, FPGAs, and microprocessors. Design the bus network carefully: terminate both ends of a long RS-485 cable, avoid star branches, keep stub lengths short, and provide a bias resistor only at one location when the transceiver configuration requires idle biasing. Validate differential swing, common-mode range, isolation requirements, and ESD grounding before releasing the PCB layout.

طلب عرض سعر اتصل بنا
MAX3490EPA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490EPA+

MAX3490EPA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490EPA+ is a 3.3V-powered, full-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 10Mbps, and an 8-pin PDIP package. It operates from a 3V to 3.6V supply and is designed for low-power industrial communication links. According to the verified product data, the device supports RS-485 and RS-422 interfaces, uses slew-rate-limited signaling, and includes short-circuit and thermal protection on the driver. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible data. These differential links are used in industrial automation, instrumentation, building controls, and data communications because they are more resistant to common-mode noise than single-ended interfaces. The MAX3490EPA+ belongs to the transceiver class within interface ICs and supports point-to-point or multipoint differential communication architectures. The principal verified features include one driver and one receiver, full duplex operation, a 3V to 3.6V supply range, and operation up to 10Mbps. The MAX3490EPA+ is identified as a true RS-485/RS-422 transceiver, while the slew-rate-limited driver helps control edge rates and reduce unwanted reflections and EMI. The verified distributor listing also identifies the package as 8-pin PDIP and lists the device as a 1/1 transceiver. The device is suited to interfaces where low-voltage digital control communicates with a field bus over a cable. Its 10Mbps capability can support high-speed data transfer, industrial control links, and equipment-to-equipment communication. The driver’s short-circuit current limiting and thermal shutdown protection help protect the output stage when a bus fault or improper termination creates excessive output stress. Applications must still observe the manufacturer’s absolute maximum ratings and recommended external-circuit requirements. For PCB implementation, use the 8-pin PDIP footprint and route the differential bus with controlled impedance when cable length, data rate, or EMI requirements justify it. Keep transceiver supply bypassing close to VCC and GND, connect the receiver and driver interface pins according to the datasheet, and select termination appropriate to the cable topology. The verified operating temperature range is -40°C to 85°C, making the part suitable for industrial temperature environments when the surrounding system requirements are met. This page consolidates verified manufacturer and distributor information, pricing references, interface selection guidance, and practical design notes for engineers evaluating the MAX3490EPA+. It does not infer unverified electrical parameters; unavailable values are explicitly marked for follow-up against the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MAX3490ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3490ESA+

MAX3490ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Maxim Integrated MAX3490ESA+ is a 3.3V low-power RS-485/RS-422 transceiver with one driver and one receiver, designed for data rates up to 10Mbps and housed in an 8-SOIC package. According to the verified product data, it is slew-rate limited and supports true RS-485 and RS-422 communication. The low 3.3V supply makes it suitable for industrial control, instrumentation, communications, and embedded systems where a compact differential interface is required. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential signals for reliable communication over wired networks. In this product category, the transmitter drives a differential bus, while the receiver converts the differential bus voltage back into a logic-level signal. RS-422 commonly supports point-to-point communication, while RS-485 supports multipoint bus arrangements. The MAX3490ESA+ combines these functions in one package, reducing the number of external interface components. The verified listing identifies the MAX3490 family as 3.3V, low-power transceivers for RS-485 and RS-422 communication. The MAX3490 device is listed by Analog Devices as a 3.3V-powered, 10Mbps, slew-rate-limited, true RS-485/RS-422 transceiver. The + suffix denotes the lead-free ordering configuration commonly shown by distributors, while the exact package and suffix conventions should be confirmed against the manufacturer ordering guide before production release. Slew-rate limiting helps control the transition speed of the driver, reducing electromagnetic interference and cable reflections associated with faster edges. This is particularly useful when the transceiver drives longer cables or imperfectly terminated buses. The 10Mbps capability supports high-speed point-to-point links, but cable length, topology, termination, grounding, and signal integrity must be evaluated as a complete system rather than treated as an isolated IC specification. Typical applications include industrial RS-485 links, building and factory automation, data acquisition equipment, motor-control systems, security equipment, and embedded communications modules. The 3.3V supply is convenient for systems using 3.3V microcontrollers, DSPs, FPGAs, or other digital controllers. Designers should verify voltage levels, driver and receiver enable timing, bus termination, protection requirements, and operating-temperature limits against the manufacturer datasheet before release. The primary design consideration is ensuring the transceiver operates within the electrical limits of the intended bus. Differential routing should use controlled impedance where practical, the ground reference should be maintained, and unused inputs should not be left floating. This page combines the verified manufacturer and distributor information with practical application guidance, packaging information, and engineering selection criteria for evaluating the MAX3490ESA+.

طلب عرض سعر اتصل بنا
MAX3490ESA+T - 10Mbps Full-Duplex RS-485/422 | Analog Devices
MAX3490ESA+T

MAX3490ESA+T - 10Mbps Full-Duplex RS-485/422 | Analog Devices

The Analog Devices MAX3490ESA+T is a 3.3V-powered, low-power RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. It supports data rates up to 10Mbps, operates from 3V to 3.6V, and is designed for full-duplex industrial communications. The tape-and-reel ordering code identifies the lead-free MAX3490ESA variant supplied on carrier tape. An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic-level signals and differential bus signals. Differential signaling reduces susceptibility to common-mode noise and allows reliable data transfer over longer cables. In the broader hierarchy, the MAX3490 belongs to the RS-485/RS-422 transceiver family within interface ICs and wired-communication semiconductors. Key features include a 10Mbps maximum data rate, 3V to 3.6V supply operation, full-duplex communication, and an integrated driver and receiver. The manufacturer describes the MAX3483, MAX3485, MAX3486, MAX3488, MAX3490, and MAX3491 as 3.3V low-power transceivers for RS-485 and RS-422 communication. These devices support industrial-control, instrumentation, data-acquisition, and factory-automation links where robust differential signaling is required. The MAX3490 provides separate transmit and receive paths for full-duplex operation, allowing the transmitter and receiver to remain active simultaneously. Its 8-SOIC surface-mount package supports compact PCB layouts, while the 3.3V supply simplifies interfacing with modern microcontrollers, field-programmable gate arrays, sensors, and industrial controllers. The exact receiver enable, driver enable, and bus-failover behavior should be confirmed against the manufacturer datasheet for the specific ordering variant before schematic sign-off. Typical applications include full-duplex RS-485 links between industrial controllers and remote I/O modules, point-to-point RS-422 interconnects in test equipment, factory-floor sensor networks, and embedded control systems. Compared with half-duplex transceivers that multiplex the driver and receiver onto the same bus pins, a full-duplex implementation can simplify timing and remove the need for software-managed bus turnaround. Designers should account for bus termination, fail-safe biasing, cable length, and grounding when using the MAX3490ESA+T. Differential buses normally require termination resistors at both ends of the cable, while bias resistors may be required to keep the bus in a defined state when no driver is active. Decoupling capacitors should be placed close to the supply and ground pins, and unused inputs should not be left floating. This page consolidates manufacturer product information, distributor pricing references, verified substitute candidates, pin-level guidance, and practical RS-485 design notes into one engineering-oriented resource. It also identifies which same-package alternatives are documented as pin-compatible replacements and where additional manufacturer verification is required.

طلب عرض سعر اتصل بنا
MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices
MAX349EAP+

MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices

Analog Devices MAX349EAP+ is a serially controlled, low-voltage 8-channel analog multiplexer with a maximum on-resistance of 100 ohms, supplied in a 20-pin SSOP package. It accepts single-supply operation from 2.7 V to 16 V or dual-supply operation from ±2.7 V to ±8 V. The matched on-resistance is limited to 16 ohms, with variation of no more than 10 ohms across the specified signal range. An analog multiplexer is an interface switch that connects one of several input or output channels to a common terminal. The MAX349 belongs to the hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. Its eight channels can be selected through a serial control interface, reducing the number of GPIO pins required when a controller must route multiple analog signals through a shared circuit. The MAX349's maximum on-resistance of 100 ohms minimizes signal attenuation when it routes low-frequency analog signals. On-resistance matching between switches is specified at 16 ohms maximum, while flatness is limited to 10 ohms over the signal range. This matching helps preserve consistent signal behavior as the selected channel changes. The device also supports operation in either signal direction, allowing it to function as either a multiplexer or a demultiplexer. The MAX349 family is intended for low-voltage equipment where analog channels must be routed through a limited number of printed-circuit-board traces. Digital control reduces routing complexity, while dual-supply support permits bipolar signal handling when paired with negative and positive rails. A single 2.7 V to 16 V supply supports lower-voltage designs where a negative rail is unnecessary. Typical uses include multiplexed data acquisition, automated test equipment, industrial measurement systems, and portable instruments. An eight-channel arrangement is useful when several sensors, divider outputs, or control signals share a common converter input. The serial interface is particularly helpful in compact systems where conserving microcontroller or processor I/O is important. Designers should verify signal amplitude, supply configuration, serial-interface timing, and switch behavior before assigning channels. Keep routed analog signals within the device's specified operating range, account for the 100-ohm maximum on-resistance when calculating divider ratios, and use the manufacturer's pin-description table when making PCB connections. The MAX349 and MAX350 are related dual-supply multiplexer families, but they should not be treated as interchangeable without verifying channel count and pinout. This product page combines the official device identity, electrical characteristics, package information, application guidance, and practical replacement considerations. It also distinguishes the MAX349 from the MAX350 and explains when a verified drop-in substitute is preferable to redesigning around a different multiplexer architecture.

طلب عرض سعر اتصل بنا
MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices
MAX349EPN+

MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices

Analog Devices MAX349EPN+ is a serially controlled, low-voltage 8-channel multiplexer with a maximum on-resistance of 100 ohm, packaged in an 18-pin DIP. It supports dual 4-channel multiplexing, bidirectional signal conduction, break-before-make switching, and a fail-safe disconnect function. Its operating temperature range is -40°C to +85°C, while the stated supply-voltage limits cover +2.7 V to +16 V and -8 V to -2.7 V. An analog multiplexer is an interface IC that connects multiple signal paths to a shared output through digitally controlled switches. The MAX349 belongs to the analog-switch and multiplexer hierarchy within interface semiconductors. By selecting one of eight input channels for a common terminal, it reduces the number of signal lines and external routing required in data-acquisition, measurement, and control systems. The dual 4-channel architecture supports differential-style routing while retaining an 8:1 multiplexing mode. Key characteristics include a maximum on-resistance of 100 ohm, 300 ns and 400 ns stated switching-time figures, 8 pF channel capacitance, and 100 pA off leakage. The MAX349EPN+ is specified for both positive and negative supply rails. Positive operation extends from +2.7 V to +16 V, while negative operation extends from -8 V to -2.7 V. Its bidirectional analog channels allow signals to pass in either direction, making the device suitable for routed analog buses rather than only one-way output selection. The serially controlled interface reduces the number of control traces required compared with a conventional parallel-address multiplexer. Its 18-PDIP package has a stated 7.62 mm body width and is compatible with through-hole assembly. Because each selected channel contributes resistance and capacitance, the device is best suited to low- and moderate-frequency analog signals where switching time and on-resistance are compatible with the measurement bandwidth. The MAX349EPN+ also specifies break-before-make operation and fail-safe disconnect behavior for controlled signal routing. Typical uses include multiplexed sensor acquisition, laboratory measurement interfaces, industrial control signal routing, communication-channel selection, and compact test systems that must route several analog inputs through a shared conversion or processing chain. The -40°C to +85°C range supports industrial-temperature equipment, while the lead-free-compatible DIP format suits through-hole prototypes and legacy-style controller boards. Designers should account for the 100 ohm maximum channel resistance, 8 pF capacitance, and stated switching times when setting source impedance, bandwidth, settling time, and gain expectations. Confirm signal amplitudes against the positive or negative supply rails, and use the manufacturer pin-description table when assigning PCB nets and connector routing. This page combines the MAX349EPN+ operating limits, package details, verified drop-in comparison, application guidance, and PCB-focused design notes to support component selection and implementation. It also distinguishes the electrically similar MAX349CPN+ temperature option from a true cross-brand replacement.

طلب عرض سعر اتصل بنا
MAX350CAP+ - Dual 4:1 Analog Multiplexer | Analog Devices
MAX350CAP+

MAX350CAP+ - Dual 4:1 Analog Multiplexer | Analog Devices

The Analog Devices MAX350CAP+ is a serially controlled, low-voltage dual 4:1 analog multiplexer with two independent 4:1 switch circuits, a maximum on-resistance of 100 ohms, and a 20-pin SSOP package. The device supports bidirectional signal conduction and operates from single or dual power supplies, making it suitable for routing low-voltage analog signals in test, measurement, communication, and control systems. An analog multiplexer is an interface IC that connects multiple signal sources to a shared destination while allowing a controller to select the active path. The MAX350 family belongs to the broader switch and multiplexer hierarchy, where its 4:1 configurations provide four inputs per circuit and reduce the number of external routing connections required in a PCB. The MAX350CAP+ provides two 4:1 circuits in one package, with maximum on-resistance of 100 ohms. On-resistance matching between switches is specified at 16 ohms maximum, while variation across the specified signal range is limited to 10 ohms maximum. The low-voltage architecture supports dual supplies from ±2.7 V to ±8 V or a single supply from +2 V to +16 V. Because these are CMOS analog switches, the device conducts equally well in either direction. The serial control interface allows an external controller to select among the four channels in each circuit, reducing the number of parallel logic connections compared with a mechanically switched multiplexer. Charge injection of 1 pC and channel capacitance of 2 pF are useful considerations when precision transient or bandwidth behavior matters. Typical uses include signal-routing modules, programmable test equipment, industrial control interfaces, data-acquisition systems, and communication equipment. The dual 4:1 arrangement is especially useful where two independent groups of analog inputs must be selected under software control while maintaining a compact 20-pin SSOP footprint. When assigning PCB tracks, keep protected or high-impedance signal paths short and use the pin-description table in the manufacturer datasheet. Check the actual signal amplitude, bandwidth, supply arrangement, and control-logic levels against the electrical characteristics before treating the 100-ohm maximum on-resistance as acceptable insertion loss. This page combines manufacturer specifications, sourcing information, compatible family options, and practical interface-design guidance. It also distinguishes verified drop-in options from related MAX349 and MAX350 devices so engineers can select by channel configuration, package, pinout, and supply requirements rather than by multiplexer function alone.

طلب عرض سعر اتصل بنا
MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MAX350CPN+

MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

Analog Devices MAX350CPN+ is a dual 4:1 analog multiplexer with 100 ohm maximum on-resistance, housed in an 18-pin plastic DIP package. It combines two independently controlled 4:1 selectors, providing eight channels of analog routing while supporting bidirectional signal conduction. An analog multiplexer is an interface IC that connects one shared signal path to multiple inputs or one input to multiple outputs. The MAX350 belongs to the broader switch and multiplexer hierarchy, where low on-resistance, matched switch characteristics, and serial control are important for preserving signal integrity in test, measurement, and communication systems. The MAX350 family provides on-resistance matched between switches to 16 ohm maximum and flat to 10 ohm maximum over the specified signal range. Its 100 ohm maximum on-resistance suits low-frequency analog routing, while serial control reduces the number of control inputs required on a constrained board. The dual 4:1 organization allows two multiplexers to operate as independent routing pairs. The device supports continuous operation from dual supplies of ±2.7 V to ±8 V. It also supports a single-supply operating mode, although the complete single-supply limits must be confirmed in the manufacturer datasheet before final rail planning. Bidirectional conduction means the selected signal may travel into or out of the common terminal without changing the switch architecture. Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and communication equipment. In each case, the serial interface reduces control-line count while the matched low on-resistance helps minimize channel-dependent attenuation. The 18-pin DIP package is appropriate for through-hole prototype, legacy, and industrial assembly where surface-mount packaging is not required. When laying out a board, keep common and switched traces short, provide a solid ground reference, and route control signals away from sensitive analog paths. Confirm supply sequencing, logic-level thresholds, signal-range limits, and exposed-pin assignments against the manufacturer datasheet before manufacturing. This page combines manufacturer specifications, verified sourcing information, drop-in replacement analysis, application guidance, and design considerations to support component selection and PCB implementation.

طلب عرض سعر اتصل بنا
MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MAX350CWN+

MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

The Analog Devices MAX350CWN+ is a serially controlled, low-voltage dual 4:1 analog multiplexer with two independent 4:1 switch sections in an 18-pin wide SOIC package. Its maximum on-resistance is 100 ohm, with on-resistance matching between switches specified to 16 ohm maximum and flatness specified to 10 ohm maximum over the operating signal range. The device supports bidirectional signal conduction. A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact. The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package. On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required. Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths. PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication. This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MAX350EPN - Dual 4:1 Multiplexer, 100Ω, 18-PDIP | Analog Devices
MAX350EPN

MAX350EPN - Dual 4:1 Multiplexer, 100Ω, 18-PDIP | Analog Devices

The Analog Devices MAX350EPN is a low-voltage, serially controlled analog multiplexer containing two 4:1 multiplexers, with a stated on-resistance of 100Ω, in an 18-pin PDIP package. The manufacturer identifies the MAX350 family as production, and the MAX350EPN is specified as a 2-circuit, 4:1 IC switch for routing multiple analog or digital signals through a shared interface. An analog multiplexer is a switch matrix that connects one of several inputs to an output under digital control. The MAX350EPN belongs to the dual 4-channel multiplexer segment of the broader interface IC hierarchy: analog switch → multiplexer → signal-routing IC. Its two independent 4:1 sections allow a controller to select among four sources per section while using a shared serial-control interface. This architecture is useful when a system must scan sensors, measurement channels, or test points without requiring a separate connector for every signal. The key documented characteristics are two switch circuits, a 4:1 configuration, 100Ω on-resistance, low-voltage operation, and an 18-pin PDIP package. The 100Ω resistance is appropriate for general-purpose low-frequency routing, although it introduces attenuation and distortion that must be considered when driving high-impedance versus low-impedance loads. The PDIP format also favors through-hole assembly and prototype or legacy-system repair rather than compact surface-mount production. Control is serial, allowing the multiplexer state to be changed by a microcontroller, test controller, or communications interface rather than by a separate parallel select line for each channel. Serial control can reduce the number of host-controller connections and simplify firmware-driven channel selection. Designers should still account for the control timing required to reach a valid output state before taking a measurement, particularly in high-speed sampling or automated test systems. Typical uses include multiplexed sensor acquisition, data-acquisition systems, industrial monitoring, test and measurement equipment, and embedded control systems with multiple low-bandwidth input channels. The part is especially relevant where two groups of four signals must share two common outputs. For higher-frequency or precision instrumentation, the system designer should compare channel capacitance, off leakage, bandwidth, and injection error against the complete MAX350 datasheet before finalizing the architecture. PCB planning should reserve the 18-pin PDIP footprint, provide a low-impedance ground reference, and route control traces away from sensitive analog paths. Keep switched-node traces short and use a continuous ground plane to reduce coupling. Confirm that downstream circuitry can tolerate the 100Ω series resistance and that the selected external resistors and amplifiers account for mux loading and switching transients. This product page combines the manufacturer’s MAX350 product information with distributor package details, application guidance, engineering caveats, and a transparent assessment of drop-in replacement availability. It also distinguishes documented MAX350EPN characteristics from parameters that still require verification from the complete manufacturer datasheet.

طلب عرض سعر اتصل بنا
MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices
MAX350EWN+

MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices

The Analog Devices MAX350EWN+ is a serially controlled, low-voltage CMOS analog multiplexer configured as two independent 4:1 switches in an 18-pin wide SOIC package. It operates from 2.7 V to 16 V and provides a maximum on-resistance of 100 ohm, with channel-to-channel matching limited to 16 ohm and resistance variation across the specified signal range limited to 10 ohm. The MAX350EWN+ conducts signal equally well in either direction, allowing it to route analog inputs or outputs through a serial interface. An analog multiplexer is a semiconductor that connects one signal path to one of several channels through controlled switches. The MAX350 family extends this category to the hierarchy of analog switch, multiplexer, routing IC, and signal-management semiconductor. Its 4:1 dual configuration provides two separately selectable channel groups, making it suitable for channel-scanning systems where multiple sensors, measurement inputs, or controlled outputs share a common signal chain. Key features include serial control, bidirectional signal conduction, low-voltage CMOS operation, and tightly matched switch resistance. The 100 ohm maximum on-resistance limits signal attenuation, while the 16 ohm maximum channel-to-channel match improves consistency when comparing readings across different channels. Its 18-pin wide SOIC package also provides a practical surface-mount footprint for industrial and instrumentation designs. The device uses a serial interface to select channels and control the multiplexers, reducing the number of package pins needed compared with a parallel-control multiplexer. This architecture is valuable in systems that route several slow or moderate-bandwidth analog signals, particularly when the microcontroller has limited general-purpose input/output capacity. Typical applications include multimeter and laboratory input switching, automated test equipment, data-acquisition modules, sensor-channel multiplexing, and control of multiple analog signal paths. The MAX350EWN+ is appropriate when bidirectional analog routing and matched resistance are more important than ultra-low on-resistance or high-speed video multiplexing. When laying out the circuit, keep analog traces short and connect the device to a stable low-noise supply. Confirm the serial interface levels and logic thresholds against the system controller, and verify that every switched signal remains within the specified analog input range. Check the full on-resistance and off-isolation characteristics in the manufacturer datasheet when the signal source is high impedance.

طلب عرض سعر اتصل بنا
MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices
MAX35103EHJ+

MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices

The Analog Devices MAX35103EHJ+ is a reduced-power time-to-digital converter with an integrated analog front end, real-time clock, and flash memory, specified for a 2.3 V to 3.6 V supply in a 32-pin TQFP (5 mm × 5 mm) package. It targets ultrasonic heat, water, and gas meters and increases the maximum time-of-flight measurement frequency in event timing mode from 2 Hz on the MAX35101 to 16 Hz. A time-to-digital converter, or ToF converter, measures the elapsed time represented by an ultrasonic pulse by converting a timing event into a digital result. The MAX35103 integrates the pulse-generation, receive-signal conditioning, timing, clock, and nonvolatile-measurement functions required by a compact ultrasonic metering front end. This integration reduces external circuitry compared with a discrete timer and analog receive chain while preserving a path to low-cost, low-power meter designs. According to the manufacturer datasheet, the MAX35103 consumes about half the average power of the MAX35101. The supplied sources do not provide a numeric average-current value, oscillator accuracy, ToF resolution, measurement range, flash capacity, temperature range, or absolute timing accuracy, so those values require confirmation in the datasheet or device evaluation before design release. The listed operating supply range is 2.3 V to 3.6 V. The integrated real-time clock and flash support metering designs that need timekeeping and persistent measurement data alongside ultrasonic time-of-flight conversion. The 16 Hz maximum event-timing frequency is particularly relevant when the meter must update more frequently than the MAX35101. Firmware, calibration, echo detection, and time-of-digital compensation still determine achievable accuracy and must be evaluated with real transducers and meter mechanics. Typical uses include ultrasonic heat meters, water meters, and gas meters. An Analog Devices evaluation kit installs the MAX35103EHJ+ and includes a USB-to-SPI interface plus graphical software for exercising device functionality. The supplied distributor records list the MAX35103EHJ+ in a 32-TQFP package and identify it as a CMOS-input, CMOS-output time-to-digital converter IC. For PCB design, place decoupling and timing-critical paths according to the manufacturer layout guidance and keep the ultrasonic analog front end away from switching nodes and digital return-current paths. Validate transducer drive amplitude, receive gain, threshold timing, clock calibration, and flash endurance under the intended flow, temperature, and supply conditions. Do not infer production suitability from the general-purpose EV kit alone.

طلب عرض سعر اتصل بنا
MAX351ESE+ - 35Ω Quad SPST Switch | Analog Devices
MAX351ESE+

MAX351ESE+ - 35Ω Quad SPST Switch | Analog Devices

The Analog Devices MAX351ESE+ is a precision, quad, SPST analog switch with a 1:1 signal configuration, 35Ω on resistance, and a 16-pin SOIC package. The four independent switch circuits are designed for routing low-frequency analog signals in test, measurement, instrumentation, and industrial control systems. Its industrial temperature grade supports operation from -40°C to +85°C. An analog switch is an electronic switching component that controls the connection between signal terminals with an external control input. As a normally closed SPST switch, the MAX351ESE+ provides a defined signal path when its control state does not request disconnection. The quad arrangement combines four switching functions in one package, reducing component count and simplifying routing in multi-channel systems. Within the broader hierarchy, it belongs to the analog switch and multiplexer family of interface ICs. The MAX351ESE+ uses a 35Ω on resistance and offers four 1:1 channels. These characteristics make it useful where moderate-resistance signal routing is acceptable and where compact, surface-mount packaging is preferred over discrete relay or transistor solutions. Its 16-pin SOIC form factor supports conventional PCB assembly and inspection processes. The device is specified as a precision analog switch rather than a high-speed digital multiplexer. Its SPST architecture simplifies each channel to one independently controlled conductive path. Design decisions should consider signal amplitude, acceptable insertion loss, source and load impedance, switching transients, and the control levels used by the surrounding logic. Typical uses include instrument signal selection, sensor-interface routing, analog test-point multiplexing, industrial control interfaces, and communication equipment. Four switch sections can manage several related channels without requiring four separate single-switch packages. The SOIC-16 outline also makes the device convenient for designs that already use standard analog and mixed-signal packages. For PCB implementation, route each switched node directly to its associated package pin and minimize loop area around sensitive analog traces. Confirm the control logic polarity, supply requirements, absolute maximum ratings, and recommended operating conditions in the manufacturer datasheet. Place bypass and signal-conditioning components where they can support low-impedance paths without creating unnecessary parasitic capacitance. This product page combines the manufacturer product description, exact-orderable-part listings, package details, temperature information, and practical routing guidance. It also identifies same-family drop-in candidates and highlights the electrical checks that must be completed before substituting a normally closed or low-leakage switch into a precision analog path.

طلب عرض سعر اتصل بنا
MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim
MAX352CPE+

MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim

Analog Devices MAX352CPE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 35Ω, and a 16-pin PDIP package. The device supports analog signal switching over a 15V range and provides low off leakage of 250pA. Its four independent switches are intended for precision routing in data acquisition, test equipment, communication systems, and signal-processing circuits. An analog switch is a semiconductor device that routes analog electrical signals between input and output terminals under digital control. The MAX352 belongs to the analog switch hierarchy, where it functions as a four-channel SPST switching network. Unlike a relay or mechanical contactor, it offers compact integration, fast switching, and low off leakage, making it suitable for signals that must be switched repeatedly under digital system control. The MAX352 series provides low on resistance below 35Ω, with channel-to-channel matching maintained within 2Ω. On-resistance remains flat over the analog signal range, with a maximum variation of 3Ω. These characteristics help reduce signal attenuation and channel-dependent errors. The normally open configuration allows each channel to remain disconnected until its corresponding control signal activates the selected path. Each switch operates independently, enabling four separately controlled routes within one package. The MAX352 is differentiated from the MAX351 by its normally open switches, while the MAX353 combines two normally open and two normally closed channels. Switching times of 175ns and 145ns are listed for the device, supporting fast control-loop and communication-interface operation. Typical uses include precision signal selection, sample-and-hold systems, multiplexed test paths, digital signal processing front ends, and communication equipment. The low 250pA off leakage is particularly useful when switching high-impedance sources, where unwanted leakage could create measurement errors or disturb sensitive analog nodes. The 16-pin PDIP package also supports straightforward through-hole assembly and prototyping. Designers should verify signal amplitude, control-logic levels, maximum current, and operating temperature against the manufacturer datasheet. Keep sensitive analog traces short, provide a stable ground reference, and avoid exceeding the switch's 15V signal or supply range. The normally open topology requires deliberate control sequencing if a default isolation state is required. This product page consolidates the MAX352 family specifications, verified source links, package information, application guidance, and compatible alternatives into an engineering-focused reference for analog signal-routing designs.

طلب عرض سعر اتصل بنا