MAX350EPN - Dual 4:1 Multiplexer, 100Ω, 18-PDIP | Analog Devices
MPN: MAX350EPN ✓ نشطMAX350EPN نظرة عامة
An analog multiplexer is a switch matrix that connects one of several inputs to an output under digital control. The MAX350EPN belongs to the dual 4-channel multiplexer segment of the broader interface IC hierarchy: analog switch → multiplexer → signal-routing IC. Its two independent 4:1 sections allow a controller to select among four sources per section while using a shared serial-control interface. This architecture is useful when a system must scan sensors, measurement channels, or test points without requiring a separate connector for every signal.
The key documented characteristics are two switch circuits, a 4:1 configuration, 100Ω on-resistance, low-voltage operation, and an 18-pin PDIP package. The 100Ω resistance is appropriate for general-purpose low-frequency routing, although it introduces attenuation and distortion that must be considered when driving high-impedance versus low-impedance loads. The PDIP format also favors through-hole assembly and prototype or legacy-system repair rather than compact surface-mount production.
Control is serial, allowing the multiplexer state to be changed by a microcontroller, test controller, or communications interface rather than by a separate parallel select line for each channel. Serial control can reduce the number of host-controller connections and simplify firmware-driven channel selection. Designers should still account for the control timing required to reach a valid output state before taking a measurement, particularly in high-speed sampling or automated test systems.
Typical uses include multiplexed sensor acquisition, data-acquisition systems, industrial monitoring, test and measurement equipment, and embedded control systems with multiple low-bandwidth input channels. The part is especially relevant where two groups of four signals must share two common outputs. For higher-frequency or precision instrumentation, the system designer should compare channel capacitance, off leakage, bandwidth, and injection error against the complete MAX350 datasheet before finalizing the architecture.
PCB planning should reserve the 18-pin PDIP footprint, provide a low-impedance ground reference, and route control traces away from sensitive analog paths. Keep switched-node traces short and use a continuous ground plane to reduce coupling. Confirm that downstream circuitry can tolerate the 100Ω series resistance and that the selected external resistors and amplifiers account for mux loading and switching transients.
This product page combines the manufacturer’s MAX350 product information with distributor package details, application guidance, engineering caveats, and a transparent assessment of drop-in replacement availability. It also distinguishes documented MAX350EPN characteristics from parameters that still require verification from the complete manufacturer datasheet.
بدائل مباشرة لـ MAX350EPN — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلMAX350EPN المواصفات
| Manufacturer | Analog Devices / Maxim Integrated |
| Product Type | Serially controlled analog multiplexer |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| On-Resistance | 100Ω |
| Supply Class | Low-voltage |
| Control Interface | Serial |
| العلبة | 18-pin PDIP |
| Number of Terminals | 18 terminals |
| نوع التركيب | Through-hole |
| Temperature Grade | Industrial |
| Package Shape | Rectangular |
| حالة دورة الحياة | Production |
دليل تكوين أطراف MAX350EPN rectangular
تكوين الأطراف لـ MAX350EPN (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX350EPN.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX350EPN مناسب لـ 6 التطبيقs: Multiplexed Sensor Acquisition, Data-Acquisition Systems, Industrial Monitoring and Control, Test and Measurement Equipment, Automated Functional Test Fixtures, Embedded Control Signal Routing.
Multiplexed Sensor Acquisition
The MAX350EPN fits sensor-aggregation designs that must route several slow or moderate-bandwidth measurement channels into a shared analog front end. Its two 4:1 sections let two groups of four inputs share two outputs, reducing connector count and analog routing complexity. The documented 100Ω on-resistance should be included in the source impedance budget because it creates attenuation when driving lower-impedance stages. Use a high-impedance instrumentation amplifier when minimizing loading is important, and confirm from the complete MAX350 datasheet that channel capacitance and leakage satisfy the sensor’s accuracy requirements.
Data-Acquisition Systems
The MAX350EPN is useful in compact data-acquisition systems where a controller must scan multiple analog channels through a serial-controlled multiplexer. Two independent 4:1 sections can support eight input positions while using one serial interface instead of separate hardware select lines. For slowly varying thermocouple, resistive, or conditioned sensor signals, the stated 100Ω resistance may be manageable, but the complete acquisition error budget must include mux loading, channel mismatch, and acquisition-settling time. Allow the selected channel to stabilize before sampling and provide a solid return path to minimize coupling into the multiplexed measurement.
Industrial Monitoring and Control
The MAX350EPN can organize an industrial monitoring board around two banks of four conditioned inputs, such as pressure, level, position, or discrete analog control signals. Its serial-control architecture simplifies microcontroller addressing and allows channel scans to be changed in software. The 18-pin PDIP format is especially convenient for legacy control systems, proof-of-concept hardware, and repairable through-hole industrial equipment. Because the MAX350EPN is documented as a low-voltage device, verify the complete supply and signal-level ranges before connecting process-control nodes. Consider isolation, surge protection, and grounding at the connector interface rather than relying on the mux alone for front-end protection.
Test and Measurement Equipment
The MAX350EPN can route a set of test sources to common measurement paths in benchtop or automated test equipment. Two 4:1 sections offer a practical way to compare four inputs against one output channel and repeat the arrangement on a second output. The serial interface supports software-driven test sequencing and can reduce the number of parallel control lines. The 100Ω on-resistance is a meaningful source impedance, so calibrate the measurement chain for nominal resistance and channel variation. Also verify the MAX350 switching time and off-leakage limits against the shortest test-settling interval and the required leakage-sensitive measurement accuracy.
Automated Functional Test Fixtures
The MAX350EPN suits functional test fixtures that need to connect multiple stimulus or return lines to a common instrument channel. Its dual 4:1 organization allows two test paths to be switched under serial control, helping the fixture adapt to different board variants without a large relay matrix. Because the device is specified with a stated 100Ω on-resistance, use it primarily for low-current, low-frequency signals where that series impedance is acceptable. Design the fixture with short routed traces, a continuous ground reference, and ample settling time between channel changes. Validate the fixture against edge rates and source capacitance present at the DUT interface.
Embedded Control Signal Routing
The MAX350EPN can route low-voltage control or feedback signals in an embedded controller when a limited number of I/O pins is available. The dual 4:1 organization allows a microcontroller to select among alternative sensor lines, actuator references, or diagnostic nodes while preserving serial-control simplicity. The 18-pin PDIP footprint suits through-hole prototypes and repair-oriented industrial controllers, although it occupies more board area than a surface-mount multiplexer. Confirm that all routed signals remain within the device’s voltage and current limits, and use the complete datasheet to evaluate leakage, injection error, and switching behavior before driving precision or fast-changing nodes.
بيانات مرجعية هندسية لـ MAX350EPN — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Package | 18-pin PDIP |
| Brand | Analog Devices / Maxim Integrated |
| Product Type | Serially controlled analog multiplexer |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| On-Resistance | 100Ω |
| Control Interface | Serial |
| Supply Class | Low-voltage |
| Mounting Type | Through-hole |
| Lifecycle Status | Production |
أبرز الفروقات
- Dual 4:1 organization in one 18-pin PDIP device (مقابلMAX349EPN)
- Serial channel selection reduces host-control wiring (مقابلMAX349EPN)
- Documented 100Ω on-resistance supports general-purpose routing (مقابلMAX349EPN)
ملاحظات التصميم
Include the documented 100Ω on-resistance in the complete source-impedance and attenuation calculation for every switched channel. The resistance is acceptable for many high-impedance measurement paths, but it can create meaningful error when driving a lower-impedance amplifier. Add the resistance, amplifier input impedance, leakage, and downstream loading to the error budget rather than evaluating the mux in isolation.
Route switched and analog signals as short, continuous traces over a solid ground plane, and keep the serial-control traces away from sensitive analog nets. Terminate unused inputs according to the manufacturer guidance once the complete pin and application information is reviewed. A low-impedance return path reduces injected noise and coupling, while keeping the 18-pin PDIP footprint consistent with the selected board outline and drill pattern.
Do not assume that another dual 4:1 multiplexer is pin-compatible merely because it has the same channel count and package. Verify control addresses, serial timing, supply requirements, active levels, and every analog pin against the MAX350 datasheet. Also allow sufficient settling time after changing the selected channel before taking a measurement; the available listing does not provide the switching-time number needed for a universal timing value.
معلومات الامتثال
The manufacturer product page confirms production status and an industrial temperature grade for MAX350EPN, but the available product information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.