المنتجات (44,000+)

MCP3426A4-E/MS - 16-Bit Dual-Channel 15 SPS ADC | Microchip
MCP3426A4-E/MS

MCP3426A4-E/MS - 16-Bit Dual-Channel 15 SPS ADC | Microchip

The Microchip Technology MCP3426A4-E/MS is a 16-bit, dual-channel, low-noise delta-sigma analog-to-digital converter with a 15-sample-per-second conversion rate, housed in an 8-MSOP package. It supports differential inputs, an integrated 2.048 V precision reference, and analog and digital power-supply operation from 2.7 V to 5.5 V. These characteristics make it suitable for precision instrumentation, industrial measurement, and low-frequency sensor acquisition. A delta-sigma ADC is an analog-to-digital converter category that uses continuous-time oversampling and digital filtering to deliver high resolution from a low-noise analog front end. The MCP3426 belongs to the broader hierarchy of ADC, data-converter IC, signal-conditioning semiconductor, and analog measurement device. Its differential inputs can reject common-mode disturbance when paired with suitable sensor arrangements, while the integrated reference simplifies calibration and reduces the number of external precision components. The MCP3426A4 provides up to 16-bit resolution, two analog input channels, and a 15 SPS conversion rate. Its differential input range extends to ±2.048 V when the internal 2.048 V reference is selected. The converter is optimized for low-noise measurements rather than high-speed waveform capture. Separate analog and digital supply connections also allow a mixed-signal board to control analog and digital supply paths independently, provided each supply remains within its specified operating range. The converter uses a one-channel delta-sigma signal chain with digital filtering to achieve accurate results at low sample rates. This architecture is appropriate for temperature, pressure, strain, potentiometer, and slow process-control signals where resolution and input-noise performance matter more than high conversion bandwidth. The integrated reference and two differential-capable input channels reduce the need for external signal-conditioning hardware in many measurement circuits. Typical uses include industrial process monitoring, laboratory data acquisition, environmental sensors, bridge-based pressure measurement, and battery-powered instrumentation. The 2.7 V to 5.5 V supply range supports both 3.3 V and 5 V systems. For designs operating from a regulated 5 V rail, the converter can also support the 2.048 V differential range around ground when the input and reference configuration permits it. Designers should pay close attention to input common-mode voltage, source impedance, filtering, grounding, and decoupling. A high-impedance sensor or resistive divider can require a longer sampling interval than the nominal conversion rate. Place the input and reference components close to the associated pins, maintain the analog and digital return paths separately, and follow the manufacturer datasheet for recommended capacitor values and layout. This page combines the exact MCP3426A4-E/MS configuration, package information, family alternatives, commercial sourcing guidance, and practical analog-design considerations. It also distinguishes true same-package options from wider ADC choices that may require different boards, interfaces, or external circuitry.

طلب عرض سعر اتصل بنا
MCP3426A4-E/SN - 16-Bit Dual-Channel I2C ADC | Microchip
MCP3426A4-E/SN

MCP3426A4-E/SN - 16-Bit Dual-Channel I2C ADC | Microchip

The Microchip Technology MCP3426A4-E/SN is a 16-bit, dual-channel, sigma-delta analog-to-digital converter with a maximum conversion rate of 240 samples per second and a 2.7 V to 5.5 V supply range. The device is packaged in an 8-pin SOIC and uses an I2C interface for digital communication. Its on-board 2.048 V precision reference supports a differential input range of ±2.048 V, while the A4 gain configuration is optimized for low-noise measurement at 15 samples per second. A sigma-delta ADC is a voltage-to-digital converter that uses oversampling, digital filtering, and noise shaping to obtain high resolution from low-noise analog inputs. Within the data-converter hierarchy, the MCP3426 belongs to the delta-sigma ADC family, which is a type of ADC used for precision measurement. Its two-channel differential architecture suits instrumentation, industrial sensing, and low-frequency process-control systems where accurate conversion of small analog signals is more important than maximum sampling speed. The principal features include up to 16-bit resolution, two analog input channels, an integrated 2.048 V reference, differential input capability, an I2C interface, and operation from 2.7 V to 5.5 V. The A4 configuration converts at 15 samples per second, providing a comparatively slow conversion rate that supports high-resolution, low-noise acquisition. The manufacturer identifies the operating temperature range as -40 °C to +125 °C, making the device suitable for industrial and extended-temperature equipment. The converter’s sigma-delta architecture shifts much of the signal processing into the digital filter. This is useful when measuring slowly changing sensor outputs because in-band noise can be reduced without requiring a high-frequency SAR converter. Differential inputs also allow a sensor to be measured across two signal nodes, rejecting common-mode disturbances when the sensor return is referenced appropriately. The integrated reference removes the need for an external reference source, simplifying analog front-end design. Typical uses include pressure and temperature sensor acquisition, current measurement, laboratory instrumentation, environmental monitoring, and low-speed industrial data logging. In these systems, the MCP3426A4-E/SN can digitize a differential sensor output and report the conversion through the I2C bus to a microcontroller or embedded controller. The 240 samples-per-second device-family maximum provides design margin for configurations that require faster acquisition than the A4 operating rate. For reliable implementation, follow the manufacturer datasheet for analog input biasing, bypass-capacitor placement, I2C pull-up selection, and input common-mode limits. Pay particular attention to source impedance and differential polarity because excessive impedance or an out-of-range common-mode voltage can degrade conversion accuracy. Place input and supply decoupling close to their associated pins and route the differential pair to minimize pickup of switching noise. This product page combines the manufacturer’s published device characteristics with practical application guidance, pin-assignment information, lifecycle status, sourcing workflow, and a constrained comparison of directly relevant family variants. It is designed to help engineers determine whether the MCP3426A4-E/SN matches the resolution, channel count, interface, speed, package, and temperature requirements of a new precision-measurement design.

طلب عرض سعر اتصل بنا
MCP3426A5-E/MC - 16-Bit Dual-Channel ADC | Microchip
MCP3426A5-E/MC

MCP3426A5-E/MC - 16-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3426A5-E/MC is a 16-bit, dual-channel delta-sigma analog-to-digital converter with differential inputs, a 15 SPS conversion rate, and an 8-DFN 2x3 mm package. The device includes an onboard precision 2.048 V reference, which supports a differential input range of ±2.048 V. Its two independent analog channels make it suitable for precision measurement, sensor acquisition, and low-frequency industrial instrumentation. A delta-sigma ADC is an analog-to-digital converter category that uses oversampling, digital filtering, and noise shaping to provide high resolution and excellent rejection of broadband and 50/60 Hz interference. The MCP3426 belongs to the broader hierarchy of delta-sigma ADC, analog-to-digital converter, data converter IC, and semiconductor. This architecture is especially useful when relatively slow acquisition must be paired with high effective resolution and stable behavior in electrically noisy environments. Key features include resolution of up to 16 bits, two differential analog inputs, and an integrated 2.048 V precision reference. The 15 SPS conversion rate favors continuous low-level monitoring rather than high-speed waveform capture. Differential input architecture helps reject common-mode noise when paired with suitable sensor circuits, while the onboard reference simplifies designs that do not require an external low-noise reference source. The compact 8-DFN package also reduces board area compared with larger leaded packages. The MCP3426 family uses a low-noise, high-accuracy delta-sigma conversion architecture and communicates through a serial interface suitable for microcontroller- and processor-based acquisition systems. The integrated reference establishes the converter's full-scale measurement basis, while external input conditioning determines whether the available range is used effectively. Differential channel structure is valuable for bridge sensors, current-shunt measurements, and other signals centered around a common reference point. The device's 2.7 V to 5.5 V operating supply range supports compatibility with common embedded supply rails. Typical applications include industrial pressure and temperature monitoring, low-speed data acquisition, current sensing, resistance measurement, and portable instrumentation. The dual-channel architecture allows two related measurements to be captured with one converter, reducing component count when both channels share suitable excitation and reference conditions. For battery-powered or low-power embedded systems, the ADC can also serve as a low-speed precision measurement front end connected to a host microcontroller over its serial interface. PCB implementation should place input, reference, and bypass connections in accordance with the manufacturer datasheet layout recommendations. Differential routing should preserve symmetry between each positive and negative input, and a quiet grounding strategy is important because the converter's resolution can expose noise generated by surrounding circuitry. Input filtering must preserve the required source impedance while preventing out-of-band noise from degrading measurement accuracy. This product page combines the Microchip family specifications, exact-orderable-package information, configuration alternatives, and application-oriented design guidance for engineers evaluating the MCP3426A5-E/MC. It also distinguishes the hardware-compatible MCP3426 family options from replacements requiring a different package or a changed serial-interface address.

طلب عرض سعر اتصل بنا
MCP3426A5-E/SN - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MCP3426A5-E/SN

MCP3426A5-E/SN - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

The Microchip Technology MCP3426A5-E/SN is a 16-bit, dual-channel delta-sigma analog-to-digital converter with differential inputs, a 15 SPS conversion rate, and an 8-pin SOIC package. Its integrated 2.048 V precision reference supports a differential input range of ±2.048 V, while the two-channel architecture supports simultaneous monitoring of two analog signals through a multiplexed front end. A delta-sigma ADC is a voltage regulator–independent type of analog-to-digital converter that uses continuous-time sampling, noise shaping, and digital filtering to provide high-resolution results from low-resolution internal converters. Its hierarchy includes ADC > data converter > analog mixed-signal IC. This architecture is especially useful when low noise, narrow-resolution requirements, and simple I2C integration matter more than very high conversion throughput. The MCP3426 family provides differential inputs, programmable gain, factory-programmed I2C addresses, and resolution up to 16 bits. The MCP3426A5-E/SN is identified specifically as a 15 SPS, dual-channel device with a sigma-delta architecture and PGA. Its integrated 2.048 V reference removes the need for an external precision reference when the full-scale input remains within the specified differential range. Its delta-sigma conversion approach prioritizes noise rejection and resolution rather than rapid sampling. The onboard reference establishes a stable conversion scale, while the PGA allows the analog input to be conditioned before conversion. Because the device uses differential inputs, common-mode noise can be reduced when the signal source and return path are balanced correctly, although the input arrangement still requires careful attention to source impedance and grounding. Typical uses include industrial process measurement, current monitoring, bridge-sensor interfaces, laboratory instrumentation, portable instrumentation, and low-frequency acquisition systems. Two channels are useful when a design must compare a sensor signal with another analog quantity or measure differential inputs across multiple multiplexed sources. For battery-powered equipment, the low-rate conversion capability supports controlled acquisition cycles, but system-level sleep strategy and reference behavior must be evaluated during power-budget calculations. PCB implementation should keep the analog input traces short, route them away from switching nodes and high-current paths, and provide a quiet ground return. Input filtering and source settling must be coordinated with the selected conversion rate. Firmware should also read the factory-programmed I2C address associated with the A5 device variant rather than assuming the address used by another MCP3426A-series member. This page combines the manufacturer device description, verified package and converter details, replacement guidance, and practical interface-design considerations. It helps engineers distinguish protocol-compatible variants, plan acquisition firmware, and assess whether the MCP3426A5-E/SN matches a precision, low-speed measurement design.

طلب عرض سعر اتصل بنا
MCP3426A6-E/MC - 16-Bit Dual-Channel ADC | Microchip
MCP3426A6-E/MC

MCP3426A6-E/MC - 16-Bit Dual-Channel ADC | Microchip

Microchip Technology MCP3426A6-E/MC is a 16-bit, dual-channel delta-sigma analog-to-digital converter operating at 15 samples per second in an 8-DFN 2 x 3 mm package. It provides differential inputs, a 2.048 V on-board precision reference, and a two-wire I2C interface for compact measurement systems. A delta-sigma ADC is an analog-to-digital converter that uses oversampling and digital filtering to provide high resolution and noise performance from low-frequency sensor signals. In the broader device hierarchy, it belongs to the ADC and DAC class, sits below data converters, and operates as a mixed-signal interface IC. Differential inputs allow the converter to reject common-mode noise when a sensor is measured across two input lines. Key features include up to 16-bit conversion resolution, two independent analog input channels, differential operation, an internal 2.048 V reference, and a two-wire I2C digital interface. The 2.048 V reference establishes a differential input range of ±2.048 V according to the Microchip product page. This combination suits sensors whose output is centered around zero and whose signal amplitude fits the converter’s differential range. The MCP3426 family combines continuous conversion operation with low-noise delta-sigma conversion. Its two-wire interface reduces the number of signal connections required when the converter shares a bus with other sensors or a microcontroller. The A6 ordering option is identified in distributor records as a 15 SPS configuration, making it appropriate for slow-changing measurements where moderate throughput is more important than maximum sampling speed. Typical uses include pressure, temperature, strain, and low-level analog sensor instrumentation, as well as industrial monitoring systems and battery-powered measurement nodes. Differential sensor connections are particularly useful when sensor wiring is long or when the measured signal is small relative to environmental electrical noise. PCB design should preserve a quiet analog signal path, provide effective decoupling at VDD and VREF, and route the differential inputs away from switching nodes and high-current traces. Differential input filtering, grounding, and connector placement can materially affect the noise performance observed in the final conversion result. This product page combines the manufacturer specifications with practical guidance for PCB implementation, application selection, pin assignment, and drop-in replacement assessment. It also identifies where speed, resolution, package, addressing, or interface differences must be checked before treating another MCP3426 ordering code as a replacement.

طلب عرض سعر اتصل بنا
MCP3426A6-E/MS - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MCP3426A6-E/MS

MCP3426A6-E/MS - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

The Microchip Technology MCP3426A6-E/MS is a two-channel, 16-bit delta-sigma analog-to-digital converter operating at 15 samples per second, with differential inputs and a 2.048 V precision internal reference. It is packaged in an 8-pin MSOP and operates from 3.3 V or 5 V supply rails over a -40°C to +125°C temperature range. The MCP3426A6-E/MS is suited to precision measurement systems that require low-noise conversion of differential sensor signals without a high-speed sampling architecture. A delta-sigma ADC is a voltage-regulating class of data-converter IC that continuously samples an analog input and uses digital noise shaping and decimation to produce a high-resolution result. Within the semiconductor hierarchy, the MCP3426A6-E/MS is a delta-sigma analog-to-digital converter, commonly called a delta-sigma ADC. Its continuous internal architecture and integrated reference favor accurate low-frequency measurements rather than high-bandwidth waveform capture. The MCP3426 family provides two differential input channels, up to 16-bit resolution, and a precision 2.048 V reference. The A6 speed grade operates at 15 samples per second, providing a deliberate balance between conversion rate, noise performance, and power-efficient precision measurement. Differential inputs also allow direct sensing of small voltages across a sensor bridge, thermocouple, or current-shunt element while rejecting common-mode disturbance. The integrated 2.048 V reference establishes a ±2.048 V differential input range and reduces the need for an external precision reference. The device supports both 3.3 V and 5 V operation, allowing integration into embedded instrumentation and industrial measurement systems. Its -40°C to +125°C operating range supports applications where temperature drift and long-term stability are important, provided the board design controls input noise, grounding, and reference-quality power. Typical uses include bridge-based pressure and force sensing, current measurement with shunt resistors, industrial process monitoring, battery-cell voltage acquisition, and low-frequency instrumentation. Differential excitation can reject power-supply ripple and ground offsets when the sensor return is connected to the converter's negative input. The 15 sps conversion rate is most appropriate for slowly changing signals rather than audio-band or high-speed industrial waveform acquisition. Design around the differential input architecture by keeping sensor traces away from switching nodes and placing input filtering close to the MSOP pins. Confirm the external resistor, capacitor, and common-mode input requirements from the manufacturer datasheet. For a new design, verify startup settling, conversion timing, digital interface levels, and package-specific layout before committing the PCB footprint.

طلب عرض سعر اتصل بنا
MCP3426A7-E/MC - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MCP3426A7-E/MC

MCP3426A7-E/MC - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

Microchip Technology MCP3426A7-E/MC is a 16-bit, dual-channel delta-sigma analog-to-digital converter with differential inputs, up to 15 SPS conversion performance, and an 8-DFN package measuring 2 x 3 mm. It belongs to the low-noise, high-accuracy MCP3426/7/8 converter family and includes an on-board precision 2.048 V reference for a differential input range of +/-2.048 V. The A7 gain configuration is designed for fine-resolution measurement of comparatively small differential signals. A delta-sigma ADC is a voltage-to-digital converter that uses oversampling and digital filtering to deliver high resolution and low noise. Within the semiconductor hierarchy, the MCP3426A7-E/MC is a data-converter IC, then an analog-to-digital converter, and finally a delta-sigma ADC. Its differential architecture measures the voltage difference between two inputs rather than the voltage relative to ground, making it useful when the signal source is balanced, floating, or centered around a common-mode voltage. The MCP3426 family provides two analog input channels and conversion resolutions of up to 16 bits. The on-chip 2.048 V reference supports a differential range of +/-2.048 V, while the A7 device is configured for applications requiring the highest gain in this family. Digital filtering suppresses out-of-band noise, and the compact 8-DFN construction supports space-constrained analog measurement boards. The 15 SPS operating point prioritizes resolution and noise performance over rapid sampling. The converter uses a sigma-delta modulation and digital-decimation architecture. Its internal reference, programmable gain stage, analog input network, and digital filter are combined to produce filtered conversion results. Differential operation rejects common-mode disturbances when the two input paths are balanced. Because this is a low-speed, high-resolution converter, the input-to-output latency and digital filter settling behavior must be considered when defining sample timing in firmware. Typical uses include precision current measurement, bridge and sensor instrumentation, industrial process monitoring, laboratory measurement equipment, and portable instruments. In a current-sense application, the ADC can digitize the output of a current-sense amplifier. In a bridge circuit, the differential input can reduce sensitivity to common-mode voltage variations. The dual-channel architecture also allows simultaneous or interleaved measurement of two related quantities, depending on the converter mode and system timing. PCB implementation should prioritize a quiet analog ground, short input traces, and placement of the external input filtering capacitors close to the associated pins. Digital communication traces should be kept away from the differential analog inputs to reduce conversion noise. Designers should also verify the required gain, common-mode range, settling time, and reference behavior against the manufacturer datasheet before fixing the front-end network. This product page combines manufacturer specifications, practical application guidance, lifecycle-aware sourcing information, and same-package family alternatives. It also highlights the distinction between the A7 gain configuration and lower-gain MCP3426 devices, helping engineers select a replacement without assuming that every member of the converter family has identical measurement characteristics.

طلب عرض سعر اتصل بنا
MCP3426A7-E/MS - 16-Bit Dual-Channel ADC | Microchip
MCP3426A7-E/MS

MCP3426A7-E/MS - 16-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3426A7-E/MS is a 16-bit, dual-channel, delta-sigma analog-to-digital converter operating from 2.7 V to 5.5 V at up to 15 samples per second in an 8-pin MSOP package. It supports two differential analog inputs, I2C communication, and an onboard 2.048 V precision reference, making it suitable for low-frequency measurement systems requiring high resolution. A delta-sigma ADC is an analog-to-digital converter category that uses oversampling and digital filtering to trade conversion speed for high resolution and noise performance. The MCP3426 belongs to the ADC and DAC hierarchy within integrated circuits, where it converts continuously varying analog voltages into digital values for measurement, control, monitoring, and data-acquisition systems. The principal features of the MCP3426A7-E/MS include 16-bit resolution, two differential input channels, a 15 SPS conversion rate, and a 2.048 V onboard reference. Its differential input architecture supports common-mode rejection, while the 2.7 V to 5.5 V supply range accommodates both 3.3 V and 5 V systems. The I2C interface reduces the number of connections required for communicating conversion results with a host controller. Technically, the converter combines a delta-sigma modulator with internal digital filtering to suppress high-frequency noise and achieve fine resolution. The internal reference establishes a differential input range of ±2.048 V when the reference is used. Conversion speed is intentionally modest at 15 SPS, allowing the device to focus on accuracy and noise rejection rather than high-bandwidth acquisition. Typical uses include industrial process monitoring, sensor instrumentation, battery-operated measurement instruments, environmental logging, laboratory data acquisition, and low-frequency pressure or temperature sensing. The dual-channel configuration allows two related analog quantities to be measured while retaining a compact 8-pin footprint. Designers should place input and reference components close to the device, keep analog traces away from switching-node and digital clock paths, and verify the input voltage against the selected gain and reference configuration. The 15 SPS conversion rate must also be considered when designing closed-loop controls or sampling waveforms that contain significant high-frequency content. This product page combines the manufacturer’s device description, distributor specifications, package information, application guidance, and a clearly qualified drop-in comparison. It also identifies the measurement, interface, layout, and performance constraints that determine whether this low-speed precision ADC fits a particular sensor or control design.

طلب عرض سعر اتصل بنا
MCP3426A7-E/SN - 16-Bit Dual-Channel ADC | Microchip
MCP3426A7-E/SN

MCP3426A7-E/SN - 16-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3426A7-E/SN is a 16-bit, dual-channel delta-sigma analog-to-digital converter with a conversion rate of 15 samples per second, differential inputs, and an integrated 2.048 V precision reference. It is packaged in an 8-pin SOIC and operates from 2.7 V to 5.5 V. A delta-sigma analog-to-digital converter is an ADC architecture that uses continuous-time oversampling and digital filtering to convert analog voltages into high-resolution digital codes. In the broader semiconductor hierarchy, the MCP3426 belongs to the ADC/DAC class, then to data converters, and finally to analog and mixed-signal integrated circuits. Its differential input architecture helps reject common-mode noise when measuring low-level sensor signals. Key features include up to 16-bit resolution, two analog input channels, one sigma-delta conversion channel, and a 2.048 V onboard reference supporting a differential input range of ±2.048 V. The I2C interface supports digital communication with a host processor, while the low-noise architecture is intended for precision measurements where slow-changing signals provide high conversion effectiveness. The MCP3426 family is designed for low-bandwidth instrumentation rather than high-speed waveform capture. The A7 speed grade performs 15 conversions per second, making it appropriate for temperature, pressure, chemical, load-cell, and industrial process measurements. The 2.7 V to 5.5 V supply range permits operation from common 3.3 V and 5 V systems, and the wide temperature range supports industrial and automotive environments. Typical uses include bridge-sensor excitation and readout, battery monitoring, current sensing, potentiometer measurement, and environmental sensor interfaces. Differential signal measurement is particularly useful when a sensor output is referenced to a nearby analog ground or when the measured signal contains significant common-mode voltage. PCB implementation should prioritize a quiet analog ground, short input traces, and separation from switching converters and high-current digital paths. Place the input bypass capacitor close to VDD and use the pin-description table in the manufacturer datasheet when assigning tracks. The effective input bandwidth must remain consistent with the selected conversion mode and digital filter. This page combines manufacturer specifications, application guidance, parameter comparisons, and drop-in guidance to support component selection, PCB implementation, and sourcing for the MCP3426A7-E/SN.

طلب عرض سعر اتصل بنا
MCP3427-E/MF - 16-Bit Dual-Channel Sigma-Delta ADC | Microchip
MCP3427-E/MF

MCP3427-E/MF - 16-Bit Dual-Channel Sigma-Delta ADC | Microchip

Microchip Technology MCP3427-E/MF is a 16-bit, two-channel, delta-sigma analog-to-digital converter with differential inputs, an onboard 2.048 V precision reference, programmable gain, and an I2C interface, housed in a 10-pin DFN package. The device is designed for low-noise, high-accuracy measurement systems where a sensor output must be converted with limited board space and low system complexity. The MCP3427-E/MF supports input measurement from small differential signals through an internal programmable-gain amplifier. Its differential input architecture helps reject common-mode noise when the measured source is referenced to a local ground or paired sensor output. The two input channels can be configured for single-ended or differential operation, allowing the converter to serve multiple analog front-end arrangements without changing the device package. Key features include up to 16-bit resolution, a 2.048 V internal reference, self-calibration of internal offset and gain for each conversion, and a serial I2C interface suitable for embedded measurement systems. The manufacturer describes the converter as a low-noise, high-accuracy delta-sigma ADC for precision data acquisition. The MCP3427-E/MF is supplied in a compact 10-VFDFN exposed-pad package, making it appropriate for space-constrained industrial, instrumentation, and sensor-interface designs. Delta-sigma conversion is especially useful when high resolution and noise rejection are more important than instantaneous conversion rate. The MCP3427 family is intended for measurements that can be filtered digitally after acquisition, such as temperature, pressure, load-cell, bridge, and slow process-control signals. The internal reference helps establish a stable conversion baseline, while the I2C interface allows a microcontroller or embedded controller to retrieve measurements without using a parallel data bus. The MCP3427-E/MF is not a high-speed waveform ADC. Its conversion rate and digital filter behavior should be considered when the application requires rapid sampling, low-latency control, or wide-band signal capture. For those requirements, a higher-bandwidth successive-approximation or pipeline converter would generally be a better architectural fit. For slow precision measurements, however, the MCP3427-E/MF provides a compact combination of resolution, differential inputs, programmable gain, and serial connectivity. Designers should pay attention to input common-mode voltage, analog noise filtering, reference stability, I2C address configuration, and decoupling around the exposed pad. The input network should limit high-frequency interference before it reaches the converter, while the digital interface should use suitable pull-up resistors and signal-integrity practices. This product page synthesizes the verified manufacturer and distributor information, package details, purchasing links, and engineering guidance for the MCP3427-E/MF.

طلب عرض سعر اتصل بنا
MCP3427-E/UN - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MCP3427-E/UN

MCP3427-E/UN - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

The Microchip Technology MCP3427-E/UN is a 16-bit dual-channel delta-sigma analog-to-digital converter with differential inputs, a 15 samples-per-second conversion rate, and a 10-MSOP package. It operates from a 3.3 V or 5 V supply and incorporates an on-board precision 2.048 V reference, providing a differential input range of ±2.048 V. The device communicates through an I2C interface for compact, low-noise measurement systems. A delta-sigma ADC is a category of analog-to-digital converter that uses continuous-time oversampling and digital filtering to convert analog input voltages into high-resolution digital codes. Its hierarchy extends from an ADC to a data-acquisition component and ultimately to a signal-chain semiconductor. Compared with flash converters, this architecture is especially useful when low noise, high effective resolution, and integrated differential input handling matter more than very high conversion speed. The MCP3427-E/UN combines two measurement channels with 16-bit resolution in one compact device. Its differential inputs help reject common-mode noise when the sensor or bridge output is centered around a biased reference. The integrated 2.048 V reference simplifies measurement designs that do not require an external precision reference, while the 15 sps rate suits slowly changing industrial, instrumentation, and sensor signals rather than high-bandwidth waveform acquisition. Each channel is processed by the converter’s delta-sigma architecture and exposed through the I2C interface. This makes the MCP3427-E/UN appropriate for systems that need accurate readings rather than rapid sampling. The 10-MSOP package also supports compact PCB layouts, although engineers must follow the manufacturer's layout guidance to preserve the low-noise performance of the analog inputs and reference circuitry. Typical uses include bridge-based pressure and load measurements, industrial process monitoring, portable instrumentation, and low-frequency sensor acquisition. Differential sensing is particularly valuable when a transducer produces a small signal riding on a larger common-mode voltage. The 3.3 V or 5 V operation also allows integration with both low-voltage embedded systems and conventional industrial control platforms. When designing around the MCP3427-E/UN, verify the selected conversion rate, digital filter behavior, input range, and reference configuration against the manufacturer datasheet. Input filtering, grounding, and I2C pull-up placement can materially affect a sensitive measurement, so the analog and digital return currents should be routed to avoid shared high-impedance paths. This product record combines the verified Microchip product information, distributor availability, package details, and same-family drop-in options. It also adds application guidance, selection criteria, and design notes intended to make the MCP3427-E/UN easier to evaluate than a distributor listing alone.

طلب عرض سعر اتصل بنا
MCP3427T-E/MF - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MCP3427T-E/MF

MCP3427T-E/MF - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

The Microchip Technology MCP3427T-E/MF is a 16-bit, dual-channel delta-sigma analog-to-digital converter with a 15 SPS conversion rate, two differential inputs, an I2C serial interface, and a 10-pin DFN package measuring 3 x 3 mm. Its on-board precision 2.048 V reference supports a differential input range of ±2.048 V. A delta-sigma ADC is a type of sigma-delta analog-to-digital converter that uses continuous-time oversampling and digital filtering to provide high-resolution conversion of slowly changing analog signals. Positioned within the ADC > data converter > semiconductor hierarchy, the MCP3427 is designed for precision measurement systems where low noise, simple connectivity, and compact implementation matter more than very high conversion speed. The MCP3427 provides two differential input channels and up to 16-bit resolution. Differential measurement rejects common-mode voltage and often improves noise performance when the source is centered around the analog ground or midpoint of the selected input range. The integrated 2.048 V reference establishes a convenient full-scale range of ±2.048 V, while the I2C interface allows the converter to connect directly to a host microcontroller or embedded control system. Internally, the converter uses a sigma-delta modulation and digital-decimation approach to average noise over the selected conversion cycle. The 15 SPS operating rate supports temperature, pressure, load-cell, potentiometer, and other slow-moving physical measurements. Its small DFN package reduces board area, but the exposed thermal pad requires a deliberate PCB thermal and layout implementation. Typical applications include industrial process monitoring, precision temperature acquisition, pressure and force measurement, low-rate instrumentation, and embedded sensor interfaces. Differential inputs are particularly useful for sensor bridges and low-amplitude signals where common-mode rejection is valuable. The I2C interface also simplifies connection to distributed acquisition systems. Route analog inputs away from switching nodes and digital clock traces, follow the manufacturer pin and layout guidance, and provide the specified input and reference capacitance close to their associated pins. Confirm the selected conversion rate, gain, and digital filter configuration before filtering the resulting measurements in firmware. This page combines the manufacturer’s device characteristics, package information, application guidance, structured comparisons, and practical design considerations to support component selection, PCB implementation, and replacement planning.

طلب عرض سعر اتصل بنا
MCP3427T-E/UN - 16-Bit Dual-Channel Sigma-Delta ADC
MCP3427T-E/UN

MCP3427T-E/UN - 16-Bit Dual-Channel Sigma-Delta ADC

The Microchip Technology MCP3427T-E/UN is a 16-bit, two-channel sigma-delta analog-to-digital converter with differential inputs, an integrated 2.048 V precision reference, and an I2C-compatible two-wire serial interface in a 10-MSOP package. It converts input signals at up to 15 samples per second and operates from a single supply of 2.7 V to 5.5 V. These characteristics position the device for precision measurement rather than high-speed waveform acquisition. An analog-to-digital converter is an integrated circuit that samples an analog voltage and produces a corresponding digital value. The MCP3427 belongs to the sigma-delta ADC class, within the broader ADC/DAC and data-converter semiconductor hierarchy. Its differential architecture accepts paired input voltages, while the internal 2.048 V reference establishes a differential measurement range of plus or minus 2.048 V. The low-rate conversion and fine resolution favor accurate sensing of slowly changing or near-static quantities. Key features include 16-bit resolution, two differential input channels, and a conversion rate of up to 15 samples per second. The on-board 2.048 V reference reduces the need for an external voltage reference in many designs, and the I2C-compatible interface supports connection to embedded controllers and digital acquisition systems. The 2.7 V to 5.5 V supply range supports common embedded, industrial, and instrumentation rails, although the normal operating temperature range and detailed absolute maximum ratings must be confirmed in the manufacturer datasheet. The device uses a sigma-delta conversion architecture to obtain high nominal resolution at relatively low sample rates. This is appropriate for pressure, temperature, position, load-cell, and slow process-control signals rather than audio sampling or high-speed vibration analysis. Differential inputs can also reject common-mode noise when the source and return paths are routed carefully. The internal reference and conversion speed should be considered together during calibration because reference accuracy contributes directly to measurement accuracy. Typical uses include industrial process monitoring, precision temperature acquisition, load-cell signal measurement, laboratory instrumentation, and low-rate sensor conditioning. Differential input wiring is important in these systems because keeping the measurement pair together reduces susceptibility to externally induced noise. An I2C host controller can configure the conversion process and retrieve each result without requiring a high-speed parallel data bus. For a new design, begin with the manufacturer pin-description table and application guidance, then verify the exposed-pad connection and decoupling requirements before layout. Keep analog input traces short, isolate them from switching nodes, and place the input and reference components where their parasitics will not materially degrade the selected conversion mode. Confirm the intended sample rate and gain configuration against the complete timing and noise specifications. This page combines the manufacturer product information, distributor listings, package details, technical fit guidance, and a concise engineering comparison. It is designed to help developers identify whether the MCP3427T-E/UN matches a precision, low-speed measurement requirement and what must be confirmed before committing the footprint to a PCB.

طلب عرض سعر اتصل بنا
MCP3428-E/SL - 16-Bit 4-Channel ADC | Microchip
MCP3428-E/SL

MCP3428-E/SL - 16-Bit 4-Channel ADC | Microchip

Microchip Technology MCP3428-E/SL is a four-channel, low-noise, high-accuracy delta-sigma analog-to-digital converter with differential inputs, up to 16-bit resolution, a 2.048 V precision internal reference, and a 14-pin SOIC package. The supported conversion rate reaches 240 samples per second, while its single supply operating range is 2.7 V to 5.5 V. The device uses a two-wire I2C-compatible serial interface for compact measurement systems. A delta-sigma ADC is a type of analog-to-digital converter that uses continuous-time oversampling and digital filtering to convert differential input voltages into high-resolution digital codes. Within the broader semiconductor hierarchy, the MCP3428 belongs to the ADC/DAC class and provides precision measurement functions for instrumentation, industrial controls, and low-frequency sensor acquisition. The MCP3428-E/SL supports four differential channels, resolution up to 16 bits, and a precision 2.048 V on-board reference. Differential input range extends to plus or minus 2.048 V when the internal reference is used. Its 240 SPS maximum conversion rate is suited to slow-changing analog quantities rather than high-bandwidth waveform acquisition, while the low-noise architecture helps preserve accuracy in bridge, potentiometer, temperature, and pressure measurements. Technically, the ADC combines delta-sigma conversion with an I2C-compatible control interface and onboard reference. Differential inputs reject common-mode noise when paired appropriately, and the internal reference reduces external-reference count in moderate-accuracy designs. The 2.7 V to 5.5 V supply range supports both 3.3 V and 5 V systems, although the selected interface voltage and available I2C bus limits must be checked during integration. Typical uses include industrial pressure and temperature acquisition, low-rate strain and bridge conditioning, potentiometer position sensing, battery-cell monitoring, laboratory measurement, and environmental monitoring. For high-speed motor control, audio sampling, or wideband vibration analysis, a higher-rate SAR or sigma-delta converter would generally be more appropriate. Designers should verify the input common-mode range and the datasheet configuration sequence before applying external signals. Place input and reference decoupling capacitors close to their pins, route analog inputs away from switching nodes, and confirm that I2C pull-up resistors satisfy the bus capacitance and rise-time requirements at the selected clock rate. This page combines verified manufacturer and distributor information, structured specification gaps, a package-aware comparison, and practical integration guidance. It also distinguishes verified ordering variants from genuine pin-compatible replacements so engineers can assess interchangeability without assuming that a similar converter is automatically a drop-in substitute.

طلب عرض سعر اتصل بنا
MCP3428-E/ST - 16-Bit 4-Channel Sigma-Delta ADC | Microchip
MCP3428-E/ST

MCP3428-E/ST - 16-Bit 4-Channel Sigma-Delta ADC | Microchip

The Microchip Technology MCP3428-E/ST is a four-channel, 16-bit delta-sigma analog-to-digital converter with differential inputs, an I2C interface, and a 14-TSSOP package. It operates from 3.3 V or 5 V, supports conversion rates up to 15 samples per second, and incorporates a precision 2.048 V internal reference. Its differential input range of ±2.048 V is useful for low-level sensor signals, while the four-channel architecture reduces the number of separate converters required in multi-sensor measurement systems. An analog-to-digital converter, or ADC, is an interface IC that converts continuous analog voltage into a numerical value suitable for processing by a microcontroller or embedded control system. The MCP3428 belongs to the delta-sigma ADC family within the broader analog and mixed-signal semiconductor hierarchy. Delta-sigma conversion is especially useful when high resolution, low noise, and relatively slow measurement are more important than very high conversion speed. The MCP3428 provides up to 16-bit resolution, four differential input channels, a 2.048 V precision reference, and a maximum 15 sps conversion rate. Its I2C interface allows a host controller to configure conversion settings and retrieve results, while the on-board reference reduces the external precision-component count. These characteristics make the device useful for temperature, pressure, strain, current, and other slowly changing industrial measurements. Its four differential inputs can reject common-mode noise when the source and return paths are routed carefully. The architecture is particularly valuable in sensors whose outputs are small relative to system supply voltage. The 14-TSSOP package also supports compact PCB layouts, although the exposed signal and reference connections require clean grounding and stable analog supply arrangements. Typical uses include process-control instrumentation, environmental monitoring, industrial sensor acquisition, laboratory measurement, and low-rate energy metering. MCP3428T-E/ST and other MCP342x family members may be considered when pin compatibility, resolution, or temperature-range requirements differ, but every substitute must be checked against the exact pinout, reference behavior, interface timing, and acquisition-cycle requirements. For implementation, use short analog traces, a quiet reference return, and decoupling close to VDD and VSS. Confirm the source impedance and settling time because the 15 sps maximum rate leaves limited time for the selected conversion cycle. Digital interface traces should be kept away from sensitive input and reference nodes to prevent I2C activity from coupling into measured voltages. This page consolidates the verified manufacturer and distributor information, separates known variants from true drop-in options, and adds engineering guidance on acquisition timing, grounding, decoupling, and replacement decisions. Those practical details help distinguish a nominal specification match from a design that can be qualified with confidence.

طلب عرض سعر اتصل بنا
MCP3428T-E/SL - 16-Bit 4-Channel Delta-Sigma ADC | Microchip
MCP3428T-E/SL

MCP3428T-E/SL - 16-Bit 4-Channel Delta-Sigma ADC | Microchip

The Microchip Technology MCP3428T-E/SL is a four-channel, 16-bit delta-sigma analog-to-digital converter with differential inputs, a 15 sample-per-second conversion rate, and a 14-SOIC package. Its integrated precision 2.048 V reference supports a differential input range of ±2.048 V, while the two-wire I2C interface provides a compact connection to embedded control systems. A delta-sigma ADC is a mixed-signal data converter that uses oversampling and digital filtering to provide high resolution and low noise in narrow-bandwidth measurements. The MCP3428 belongs to the ADC and DAC > Analog-to-digital converter product hierarchy and is suited to precision acquisition systems rather than high-speed waveform capture. Its conversion architecture prioritizes accurate, stable readings from slowly changing or low-frequency sensor signals. The MCP3428 provides four differential input channels, 16-bit resolution, a 2.048 V precision internal reference, and a specified conversion rate of 15 SPS. Differential inputs reject common-mode noise when paired with suitable sensor bridges or instrumentation amplifiers. The integrated reference reduces external component count, while the I2C interface allows the converter to share a two-wire bus with sensors, EEPROM, and other compatible peripherals. The -E/SL ordering option is associated with the automotive-grade AEC-Q100 qualification indicated in the product documentation and uses a 14-pin SOIC package. Tape-and-reel packaging supports automated production and pick-and-place assembly. The SOIC body is listed at 3.90 mm width, and the gull-wing terminal form is compatible with conventional surface-mount assembly and board-level inspection processes. Typical uses include industrial pressure and temperature acquisition, bridge-sensor measurement, laboratory instrumentation, battery monitoring, and embedded environmental sensing. Differential channel pairing is particularly useful when the measured quantity is represented by a small voltage difference riding on a larger common-mode voltage. Firmware must configure the input channel, gain, resolution, and conversion timing through the device's serial register interface. Designers should allow the digital filter and continuous-conversion settling behavior to determine the valid sampling interval. Input filtering, reference bypassing, grounding, and I2C pull-up placement are as important as ADC resolution because they determine whether system-level accuracy approaches the converter's intrinsic performance. This page combines manufacturer specifications, application guidance, drop-in family comparisons, and practical design considerations to support component selection, schematic planning, PCB layout, and sourcing decisions for the MCP3428T-E/SL.

طلب عرض سعر اتصل بنا
MCP3428T-E/ST - 16-Bit 4-Channel ADC | Microchip
MCP3428T-E/ST

MCP3428T-E/ST - 16-Bit 4-Channel ADC | Microchip

The Microchip Technology MCP3428T-E/ST is a four-channel, 16-bit delta-sigma analog-to-digital converter with differential inputs, a two-wire I2C interface, and a 14-TSSOP package. Its headline characteristics include up to 16 bits of resolution, four input channels, differential measurement capability, a precision 2.048 V onboard reference, and conversion rates up to 240 samples per second. The internal reference supports a differential input range of ±2.048 V, allowing the converter to measure small bipolar sensor signals without an external reference source. An ADC is an analog-to-digital converter, a data-converter IC that translates continuous voltage signals into numeric values for processing, measurement, logging, or control. Delta-sigma ADCs belong to the data-converter and mixed-signal semiconductor hierarchy. They are especially useful when low noise, high resolution, and good rejection of unwanted high-frequency energy matter more than very high sampling rates. The MCP3428 combines that conversion technique with differential inputs in a compact surface-mount package. The device provides four differential-capable channels, selectable conversion speeds, and 16-bit output resolution. Its precision 2.048 V reference simplifies system design when an external precision reference is unnecessary. The I2C interface reduces the number of signal lines required to connect the converter to a microcontroller or embedded controller. These features make the part suitable for industrial process measurement, low-level sensor acquisition, portable instrumentation, and precision analog monitoring systems. The MCP3428 uses a sigma-delta conversion architecture, which supports accurate measurement of slowly changing or low-bandwidth signals while offering digital averaging benefits. Differential inputs can reject common-mode voltage and noise when the source is arranged with paired signal connections. Engineers should still account for the source impedance, acquisition settling behavior, reference accuracy, input filtering, and conversion time when interpreting the results. The converter's low-rate measurement focus is more important for process and sensor signals than for waveform capture. Typical applications include industrial pressure and temperature monitoring, laboratory measurement equipment, battery-powered data acquisition, environmental sensors, and low-frequency closed-loop control. Differential excitation also benefits bridge sensors and current-sense systems where rejecting common-mode disturbance improves measurement integrity. The 14-TSSOP package supports compact PCB layouts, although correct decoupling and quiet analog routing remain essential. Place the reference and analog input routing in accordance with the manufacturer datasheet, and use separate analog and digital return paths to minimize converter and digital-switching noise. Confirm the selected conversion rate against the required response time because faster conversion settings may not preserve the same noise performance as the slowest settings. This page combines the manufacturer specifications, sourcing guidance, application analysis, and drop-in replacement limitations into a practical engineering reference.

طلب عرض سعر اتصل بنا
MCP3461-E/ST - 16-Bit 153.6 kSPS ADC | Microchip
MCP3461-E/ST

MCP3461-E/ST - 16-Bit 153.6 kSPS ADC | Microchip

The Microchip Technology MCP3461-E/ST is a 16-bit delta-sigma analog-to-digital converter with two single-ended or one differential input, a programmable data rate up to 153.6 kSPS, and a 20-pin TSSOP package. It operates across the verified temperature range of -40°C to +125°C and is supported as an active Microchip product. A delta-sigma ADC is an analog-to-digital converter category that uses oversampling and digital filtering to provide high-resolution conversion suitable for precision measurement. Within the signal-chain hierarchy, the MCP3461-E/ST belongs to the ADC and data-acquisition converter family, combining an analog input stage, sigma-delta modulator, digital filter, and serial interface in one low-noise device. Integrated functions help reduce the number of external components required in a measurement system. The MCP3461/2/4R family includes an internal voltage reference, internal oscillator, temperature sensor, and burnout-sensor detection. The MCP3461-E/ST also offers programmable output data rates up to 153.6 kSPS, making it suitable for sensors, process-control measurements, and industrial data-acquisition systems that prioritize resolution over very high conversion latency. The converter uses a delta-sigma architecture to achieve 16-bit nominal resolution while rejecting out-of-band noise through its digital decimation filter. The MCP3461R version is identified by Microchip as a preferred, pin-compatible option for new designs because it includes an onboard voltage reference that is not included in the MCP3461. Engineers should therefore verify the selected suffix and external reference configuration before making a direct substitution. Typical uses include bridge and pressure sensor interfaces, temperature measurement, industrial process monitoring, laboratory instrumentation, and embedded data-acquisition systems. Its integrated reference, oscillator, temperature sensor, and burnout detection are especially useful where component count, calibration overhead, and predictable operation matter. The principal design consideration is matching the input, reference, and digital interface requirements to the exact MCP3461 variant. MCP3461-E/ST and MCP3461R-E/ST share the 20-pin TSSOP footprint, but the R version adds an internal voltage reference; firmware, reference selection, and board-level requirements must be reviewed before interchange. Filtering characteristics, data rate, and digital timing should also be evaluated for the target measurement bandwidth. This page consolidates verified manufacturer and distributor information, package details, lifecycle status, sourcing data, and practical selection guidance. It also distinguishes true same-footprint alternatives from broader functional equivalents so engineers can identify which substitutions require additional design review.

طلب عرض سعر اتصل بنا
MCP3461R-E/ST - 16-Bit 153.6kSPS ADC | Microchip
MCP3461R-E/ST

MCP3461R-E/ST - 16-Bit 153.6kSPS ADC | Microchip

The Microchip Technology MCP3461R-E/ST is a low-noise, 16-bit delta-sigma analog-to-digital converter with two single-ended or one differential input channel, a maximum programmable data rate of 153.6 kSPS, and a 20-pin TSSOP package. It operates from a 2.7 V to 3.6 V analog supply and a 1.8 V to 3.7 V digital supply, providing a compact converter for precision industrial, instrumentation, and sensor-measurement systems. A delta-sigma ADC is a category of data-converter IC that uses continuous-time oversampling and digital filtering to obtain high resolution and excellent noise performance. Its role within the broader semiconductor hierarchy is analog-to-digital converter, data-acquisition IC, signal-chain component, and ultimately electronic measurement interface. The MCP3461R-E/ST is designed to digitize low-frequency analog signals where fine resolution, stable conversion performance, and low circuit complexity are more important than very high sample rates. Key device characteristics include 16-bit resolution, an output data rate of up to 153.6 kSPS, one differential input or two single-ended inputs, an SPI interface, an internal voltage reference, an internal oscillator, a programmable gain amplifier, and an integrated temperature sensor. Typical signal-to-noise ratio is 97.3 dB, while typical integral nonlinearity is 7 ppm. The converter also supports clock frequencies from 1 MHz to 20 MHz or from 3.3 MHz to 6.6 MHz, depending on the operating mode. The delta-sigma conversion architecture filters noise through oversampling and digital decimation, making the device appropriate for pressure, temperature, level, load-cell, and laboratory measurement signals. Its internal reference and oscillator reduce external component count, while the 20-pin TSSOP package simplifies routing in compact data-acquisition boards. The SPI interface supports deterministic communication with a host microcontroller or digital controller. Typical uses include industrial process monitoring, precision temperature measurement, pressure transducers, portable instrumentation, low-frequency sensor acquisition, and embedded data loggers. For applications requiring more independent analog inputs, related four-channel and dual-channel members of the MCP346x family can provide additional channel capacity, but software configuration, pin allocation, and acquisition sequencing must be checked before substitution. When designing a board around the MCP3461R-E/ST, place the input, reference, and decoupling networks close to the device and keep sensitive analog traces short and separated from digital switching paths. Select the clock and decimation settings so that the resulting output-data rate meets the signal bandwidth without sacrificing the required noise performance. Account for the 2.7 V minimum analog supply when designing the sensor interface and reference headroom. This product page combines the manufacturer specifications with application guidance, parameter comparisons, and clearly qualified drop-in options. It helps engineers evaluate channel count, reference configuration, temperature range, package compatibility, interface behavior, and power-supply requirements before committing the MCP3461R-E/ST to a production design.

طلب عرض سعر اتصل بنا
MCP3461RT-E/NC - 16-Bit 153.6 kSPS Delta-Sigma ADC | Microchip
MCP3461RT-E/NC

MCP3461RT-E/NC - 16-Bit 153.6 kSPS Delta-Sigma ADC | Microchip

The Microchip Technology MCP3461RT-E/NC is a low-noise, 16-bit delta-sigma analog-to-digital converter with a programmable data rate of up to 153.6 kSPS. It provides one analog input channel, supports a 2.7 V to 3.6 V analog supply range, and is packaged in a 20-pin UQFN measuring 3 mm by 3 mm. A delta-sigma ADC is a data-converter category that uses oversampling and digital filtering to trade conversion speed for high resolution and noise performance. Within the broader hierarchy, it is an ADC, then a data converter, then an analog and mixed-signal semiconductor. The MCP3461R family is designed for precision measurement systems where a compact converter, serial interface, and integrated support functions can reduce external component count. Key features include 16-bit resolution, a maximum conversion rate of 153.6 kSPS, and a 97.2 dB signal-to-noise plus distortion ratio. The device integrates an internal voltage reference, internal oscillator, temperature sensor, burnout detector, and multiplexers. Its SPI interface provides a straightforward connection to microcontrollers and digital signal processors, while the integrated reference and oscillator help reduce the number of external precision components. The converter uses a delta-sigma architecture to support low-noise measurements of slowly changing analog signals. A programmable data rate allows designers to balance conversion speed, output rate, and noise performance. The listed operating temperature range of -40 °C to +125 °C supports applications across industrial and automotive temperature ranges, while the R suffix identifies the integrated-reference version preferred for new designs. Typical uses include industrial process-control loops, automotive pressure and position sensing, battery-management monitoring, temperature measurement, and low-bandwidth sensor acquisition. The SPI output is particularly useful where a compact controller-based measurement node is required. Systems can use the integrated temperature sensor for local diagnostics and the burnout detector to identify sensors or external circuitry operating outside expected limits. Careful layout and filtering remain important because delta-sigma performance depends on a quiet analog supply, a clean digital interface, and well-controlled input settling. Place input, reference, and decoupling connections according to the pin-description table and layout guidance in the Microchip Technology MCP3461/2/4R family datasheet, and evaluate digital return currents so they do not pass through the analog input return path. This product page combines the manufacturer specification summary, package and ordering information, pricing references, and practical replacement guidance. It also distinguishes the UQFN automotive-temperature ordering option from TSSOP-package family members that cannot replace this part without a PCB footprint change.

طلب عرض سعر اتصل بنا
MCP3461T-E/NC - 16-Bit 153.6 ksps ADC | Microchip
MCP3461T-E/NC

MCP3461T-E/NC - 16-Bit 153.6 ksps ADC | Microchip

The Microchip Technology MCP3461T-E/NC is a single-channel, 16-bit delta-sigma analog-to-digital converter with a maximum conversion rate of 153.6 ksps, a 3 V supply, and a 20-UQFN 3 x 3 mm package. It is designed for precision signal acquisition where low-noise conversion, compact implementation, and serial digital output are important. An ADC is an interface IC that converts an analog voltage into a digital value for processing by a microcontroller, DSP, FPGA, or data-acquisition system. The MCP3461 belongs to the delta-sigma ADC family, which uses continuous-time sampling and digital filtering to provide high resolution and noise performance. It sits within the broader analog-to-digital converter and data-acquisition semiconductor hierarchy. The principal device characteristics are 16-bit resolution, one analog input, operation from a 3 V supply, and conversion throughput up to 153.6 ksps. The low-noise architecture makes the converter appropriate for slow or medium-speed measurements where input signals must be resolved accurately. Its compact 20-UQFN package also supports space-constrained instrumentation and embedded control designs. The MCP3461 family supports single, differential, and multiplexed measurement arrangements depending on the selected device and system configuration. Digital communication through a serial interface allows conversion results to be transferred efficiently to a host processor. Because the MCP3461T-E/NC does not include the onboard voltage reference offered by the MCP3461R, the system must provide an appropriate external reference. Typical uses include industrial process measurement, precision instrumentation, sensor acquisition, laboratory equipment, and low-bandwidth communication receivers. In these systems, the ADC converts a conditioned sensor or control signal into a digital value while the delta-sigma filtering helps suppress out-of-band noise. Designers should pay particular attention to reference-voltage accuracy, analog input range, source impedance, sampling behavior, digital-interface timing, and decoupling. The 3 x 3 mm UQFN package also requires a land pattern capable of supporting its exposed thermal pad and adequate copper area for stable operation. This page combines the manufacturer product information, exact MPN attributes, package details, verified source links, drop-in family guidance, and practical design considerations to simplify component selection and board-level implementation.

طلب عرض سعر اتصل بنا
MCP3461T-E/ST - 16-Bit, 153.6 ksps ADC | Microchip
MCP3461T-E/ST

MCP3461T-E/ST - 16-Bit, 153.6 ksps ADC | Microchip

The Microchip Technology MCP3461T-E/ST is a 16-bit, single-channel, low-noise delta-sigma analog-to-digital converter with a maximum conversion rate of 153.6 ksps and an SPI interface, housed in a 20-pin TSSOP package. The converter operates from a 3 V supply and is designed for applications requiring precise digital measurement of low-bandwidth analog signals. A delta-sigma ADC is an analog-to-digital converter that uses continuous-time oversampling, noise shaping, and digital filtering to convert an analog input into a high-resolution digital result. Within the broader ADC hierarchy, the MCP3461T-E/ST belongs to the precision sigma-delta converter class and provides a compact interface for industrial instrumentation, sensor measurement, and embedded control systems. The key features of this device include 16-bit resolution, one analog input channel, a maximum sample rate of 153.6 ksps, low-noise operation, and a serial peripheral interface for communication with a host controller. Its single-channel architecture reduces board complexity when only one analog quantity must be measured, while the 20-pin TSSOP package supports compact surface-mount layouts. The MCP3461T-E/ST belongs to the MCP3461 family of low-noise delta-sigma ADCs. Its digital conversion process provides a straightforward alternative to high-speed flash converters in measurement systems that prioritize resolution and noise performance over instantaneous conversion latency. Configuration and result transfer through the SPI interface allow it to be paired with microcontrollers, DSPs, and other embedded controllers. Typical uses include precision temperature measurement, bridge or pressure sensor conditioning, industrial process monitoring, laboratory instrumentation, and low-frequency data-acquisition systems. For applications requiring several independent analog inputs, an external analog multiplexer may be used when switching accuracy and settling requirements permit. PCB design should prioritize a short, shielded analog input path, solid grounding, and placement of input and reference-network components close to the converter. Designers should also evaluate the digital interface timing, power-supply noise, and acquisition timing against the selected data rate before finalizing the signal chain. This product page combines the manufacturer’s converter specifications, packaging information, lifecycle guidance, and pin-compatible family options with practical guidance for sourcing, PCB implementation, and ADC selection. The result supports faster component evaluation while keeping the critical engineering trade-offs visible.

طلب عرض سعر اتصل بنا
MCP3462-E/ST - 16-Bit Dual 153.6kSPS ADC | Microchip
MCP3462-E/ST

MCP3462-E/ST - 16-Bit Dual 153.6kSPS ADC | Microchip

The Microchip Technology MCP3462-E/ST is a low-noise, 16-bit delta-sigma analog-to-digital converter with two differential or four single-ended input channels, a programmable conversion rate up to 153.6 kSPS, and a 20-pin TSSOP package. The converter operates from a 2.7 V to 3.6 V analog supply and a 1.8 V to 3.7 V digital supply. A delta-sigma ADC is a signal-processing category of analog-to-digital converter that continuously oversamples and digitally filters its input. Unlike a flash or successive-approximation ADC, the MCP3462 trades conversion latency for high resolution, low noise, and integrated signal conditioning. It belongs to the broader ADC > data converter > mixed-signal semiconductor hierarchy and is intended for precision measurement rather than high-speed waveform capture. Key features include 16-bit resolution, four single-ended or two differential inputs, and a maximum programmable data rate of 153.6 kSPS. Integrated resources include an internal oscillator, programmable gain amplifier, temperature sensor, and digital interface functions described by the manufacturer. The MCP3462 uses an external voltage reference, while the pin-compatible MCP3462R adds an onboard reference and is identified by Microchip as the preferred option for new designs. The MCP3462 combines a delta-sigma conversion core with programmable input gain and flexible data acquisition modes. Its internal oscillator reduces the need for an external clock source, while the temperature sensor supports system-level monitoring. The dual differential-input architecture allows common-mode rejection of paired sensors, and the four single-ended channels permit multiplexing for multi-sensor systems. The 2.7 V minimum analog supply supports low-voltage industrial instrumentation, although the analog and digital operating ranges must remain within their respective limits. Typical uses include industrial process measurement, battery and power-system monitoring, environmental sensing, portable instrumentation, and low-frequency precision data acquisition. The integrated temperature sensor can assist with board-level thermal monitoring, while the programmable gain amplifier supports inputs that vary substantially in amplitude. Because the device is a delta-sigma ADC, software or digital filtering and a settling-time budget must be considered when measuring rapidly changing signals. The principal design consideration is reference quality. The MCP3462 requires an external reference, and reference noise, layout distance, and input filtering directly influence conversion results. Place the analog inputs, external reference, and associated bypass components close to the converter, keep digital interfaces away from sensitive analog inputs, and follow the manufacturer’s recommended decoupling and grounding arrangement. This page combines manufacturer positioning, distributor availability, verified package and channel information, pin-compatible same-family alternatives, and practical selection guidance. It also distinguishes the externally referenced MCP3462 from the onboard-reference MCP3462R so engineers can choose the appropriate variant without treating every TSSOP ADC as an interchangeable replacement.

طلب عرض سعر اتصل بنا
MCP3462R-E/ST - 16-Bit 153.6kSPS Delta-Sigma ADC | Microchip
MCP3462R-E/ST

MCP3462R-E/ST - 16-Bit 153.6kSPS Delta-Sigma ADC | Microchip

The Microchip Technology MCP3462R-E/ST is a low-noise 16-bit delta-sigma analog-to-digital converter (ADC) with a programmable data rate up to 153.6 kSPS, four single-ended or two differential input channels, and an integrated voltage reference, packaged in a 20-lead TSSOP. The -E grade extends operation from -40 °C to +125 °C and the -ST suffix denotes the 20-lead TSSOP package. A delta-sigma ADC is a type of analog-to-digital converter that uses a sigma-delta modulator to shape quantization noise into the out-of-band region, where it is removed by a digital decimation filter. Within the broader hierarchy of data converter ICs -> analog-to-digital converter -> data acquisition building block -> semiconductor, this architecture is the standard choice for high-resolution, low-bandwidth measurement of slowly varying or slowly changing analog signals such as temperature, pressure, load-cell bridge outputs, and battery voltage. Key features of the MCP3462R include 16-bit resolution, a maximum 153.6 kSPS conversion rate, an internal 2.048 V-class voltage reference with an internal oscillator, a programmable gain amplifier (PGA), an integrated temperature sensor, and burnout sensor detection for open-circuit diagnostics. A typical SNR of 97.3 dB and flexible digital interface handling let the same part cover industrial process control, energy metering, and portable instrumentation. The analog supply operates from 2.7 V to 3.6 V while the digital supply accepts 1.8 V to 3.7 V, which lets the ADC interface directly to 1.8 V microcontrollers and 3.3 V logic without level translators. The serial interface supports SPI-compatible framing, and the integrated reference and oscillator remove the external precision reference and crystal normally required, reducing board area and total solution cost. Typical applications include precision temperature sensing with RTDs and thermocouples, load-cell and strain-gauge front ends, industrial data acquisition modules, battery-powered portable instrumentation, and energy metering where a low-noise 16-bit conversion with built-in diagnostics is needed. When designing with the MCP3462R-E/ST, keep analog and digital return currents separated and place the input RC filter close to the VIN pins. The internal reference and internal oscillator simplify the BOM, but for the lowest gain error across temperature the external reference option should be evaluated against the accuracy target of the end measurement. This page consolidates parametric detail, package and pin information, drop-in replacement candidates, application guidance, and practical design notes into one reference so that design, sourcing, and review teams can evaluate the MCP3462R-E/ST without piecing the data together from multiple listings.

طلب عرض سعر اتصل بنا