المنتجات (44,000+)

MCP3562T-E/NC - 24-Bit Dual-Channel 153.6 kSPS ADC
MCP3562T-E/NC

MCP3562T-E/NC - 24-Bit Dual-Channel 153.6 kSPS ADC

The Microchip Technology MCP3562T-E/NC is a low-noise, 24-bit sigma-delta analog-to-digital converter with two differential or four single-ended inputs and a maximum conversion rate of 153.6 kSPS. The device operates from a 3 V supply and is packaged in a 20-pin UQFN measuring 3 x 3 mm. An analog-to-digital converter is an integrated circuit that converts continuous voltage signals into numerical values for processing, measurement, or transmission. The MCP3562 belongs to the delta-sigma ADC hierarchy, where a modulator and digital filter extract high-resolution measurements from low-frequency analog inputs. Its dual-channel architecture supports two differential channels or four single-ended channels, making it suitable for bridge sensors, pressure transducers, current sensing, and multi-channel instrumentation. The MCP3562T-E/NC provides 24-bit resolution, four analog input options, and programmable output data rates up to 153.6 kSPS. Its low-noise architecture is intended for systems in which small sensor signals must be resolved accurately, including industrial process monitoring, medical instrumentation, portable measurement equipment, and laboratory data-acquisition systems. Its sigma-delta conversion principle trades conversion speed for resolution and noise performance. The two-channel differential configuration can reject common-mode noise present on sensor lines, while the four single-ended inputs simplify multiplexed measurement. Digital filtering and programmable data rates allow the system designer to balance conversion speed, noise bandwidth, and power consumption according to the measurement requirement. Typical uses include strain-gauge and load-cell front ends, thermocouple interface boards, pressure and flow instrumentation, battery-bank monitoring, and factory automation modules. The 3 V supply also integrates naturally with low-voltage sensor nodes and microcontrollers operating from the same rail. When laying out the circuit, use short, symmetrical routing for differential inputs and place the analog input and reference connections away from switching nodes and high-current traces. Verify the external reference and input voltage limits against the manufacturer datasheet before applying sensor excitation. This page organizes the conversion performance, channel options, package details, and pin-compatible Microchip alternatives into a design-focused reference. It also adds practical layout guidance, application fit analysis, and a parameter comparison for engineers evaluating replacements before schematic release.

طلب عرض سعر اتصل بنا
MCP3562T-E/ST - 24-Bit Dual-Channel ADC | Microchip
MCP3562T-E/ST

MCP3562T-E/ST - 24-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3562T-E/ST is a low-noise 24-bit delta-sigma analog-to-digital converter with four single-ended or two differential input channels and a maximum programmable data rate of 153.6 kSPS. It is packaged in a 20-pin TSSOP and is intended for precision measurement, sensor acquisition, and industrial signal-chain applications. A delta-sigma ADC is a class of analog-to-digital converter that uses oversampling, digital filtering, and noise shaping to obtain high resolution from a low-noise analog input. The MCP3562T-E/ST supports four single-ended or two differential channels, giving designers flexibility for measuring several unipolar sensors or two balanced bridges while retaining a compact 20-pin TSSOP footprint. Key features include 24-bit resolution, programmable output data rates up to 153.6 kSPS, and four single-ended or two differential analog inputs. The converter architecture is designed for low-noise measurement rather than high-speed waveform capture, making it suitable for pressure, temperature, load-cell, current, and process-control signals. Its external-reference requirement should be considered carefully because the related MCP3562R includes an onboard voltage reference while MCP3562 does not. The MCP3562 family uses a serial interface for configuration and data transfer. In a typical measurement circuit, analog signals pass through protection, filtering, and gain stages before entering the ADC inputs. Digital filtering then rejects out-of-band noise, while an external voltage reference establishes the conversion scale. This combination supports deterministic sensor measurements with relatively high effective resolution. Typical uses include industrial process monitoring, portable instrumentation, environmental sensing, battery-powered measurement systems, and precision analog front ends. The TSSOP package also facilitates compact board layouts, although careful grounding, reference routing, and input filtering remain necessary to preserve the converter’s low-noise performance. When designing a board around the MCP3562T-E/ST, verify the external reference voltage, digital supply levels, interface signals, and channel configuration against the manufacturer datasheet. Confirm that the selected data rate and digital filter settings provide enough conversion latency for the application. For new designs where an onboard reference simplifies the power tree, evaluate the manufacturer-recommended MCP3562R option and confirm its complete pin compatibility. This page combines the manufacturer’s device information with practical selection guidance, application fit, and direct replacement considerations. It is designed to help engineers identify whether the MCP3562T-E/ST matches their channel count, resolution, data-rate, package, and reference requirements before requesting a quote.

طلب عرض سعر اتصل بنا
MCP3564-E/ST - 24-Bit 153.6kSPS ADC | Microchip
MCP3564-E/ST

MCP3564-E/ST - 24-Bit 153.6kSPS ADC | Microchip

Microchip Technology MCP3564-E/ST is a low-noise 24-bit delta-sigma analog-to-digital converter with eight single-ended or four differential inputs, a maximum data rate of 153.6 ksps, and a 20-lead TSSOP package. The converter supports 2/4/8-channel families and is intended for precision analog signal acquisition where a high-resolution digital output and flexible input configuration are required. The MCP3564 does not include the onboard voltage reference found in the preferred MCP3564R variant. A delta-sigma ADC is a type of analog-to-digital converter that uses oversampling, noise shaping, and digital filtering to convert continuous analog voltages into high-resolution digital codes. Within the data-converter hierarchy, it belongs to the ADC/DAC category and provides an alternative to successive-approximation and flash converters when low-noise integration and programmable output data rates are more important than very low conversion latency. The verified product information identifies a 24-bit conversion resolution, a maximum output rate of 153.6 ksps, and eight single-ended or four differential input channels. The low-noise architecture is useful when measuring sensor outputs, process-control signals, or low-amplitude analog quantities where the ADC must preserve signal detail while converting it into a digital representation. Its 20-lead TSSOP package supports conventional surface-mount PCB assembly. The MCP3564 is one member of the MCP3561/2/4 family, which provides a common platform for two-, four-, and eight-channel low-noise 24-bit delta-sigma converter applications. Programmable data-rate capability allows the interface timing to be matched to different measurement bandwidths. This can reduce unnecessary digital data transfer in systems where the source changes slowly, while faster rates remain available for dynamic measurements. Typical uses include industrial process monitoring, precision instrumentation, environmental sensing, factory data acquisition, and embedded measurement systems. Eight single-ended channels are useful for monitoring several sensors with a common ground reference, while four differential channels help reject common-mode noise when the source is balanced or when the analog front end can drive differential signals. Designers should account for the absence of an onboard reference in the MCP3564 and provide an appropriate external voltage reference. Input filtering, source settling, grounding, and PCB layout should preserve the low-noise performance of the converter. The exact electrical limits, reference requirements, interface details, and recommended external circuitry must be verified in the manufacturer datasheet before production design. This product record combines verified manufacturer and distributor information with a structured comparison against the pin-compatible MCP3564R-E/ST. It also highlights selection trade-offs, pricing context, and practical design considerations that help engineers distinguish the standard MCP3564 from the reference-equipped MCP3564R without relying on undocumented assumptions.

طلب عرض سعر اتصل بنا
MCP3564R-E/ST - 24-Bit Quad-Channel Delta-Sigma ADC | Microchip
MCP3564R-E/ST

MCP3564R-E/ST - 24-Bit Quad-Channel Delta-Sigma ADC | Microchip

Microchip MCP3564R-E/ST is a low-noise 24-bit delta-sigma analog-to-digital converter with eight single-ended or four differential input channels, a programmable data rate up to 153.6 kSPS, and an integrated voltage reference in a 20-lead TSSOP package. A delta-sigma ADC is a data-converter IC that oversamples its input and uses digital filtering to reduce quantization noise. Within the conversion hierarchy, the MCP3564R-E/ST belongs to the ADC > delta-sigma ADC > data converter > integrated circuit family. This architecture is particularly useful when a sensor or transducer produces a relatively slow signal that must be digitized with high resolution and low noise. The converter supports eight single-ended or four differential inputs, allowing one device to serve multichannel measurement systems. Its 24-bit resolution captures small changes in voltage, while the programmable output data rate of up to 153.6 kSPS provides flexibility between measurement speed and noise performance. The integrated voltage reference reduces the external component count and simplifies board-level design compared with an ADC that requires a separate reference circuit. MCP3564R-E/ST is offered in a leaded 20-pin TSSOP package measuring 6.4 mm by 6.4 mm. Its specified extended-temperature operation ranges from -40 °C to +125 °C. The package format supports conventional leaded assembly and inspection while providing enough pin count for multiple analog inputs, digital data, power, clock, and configuration connections. Typical uses include industrial process monitoring, sensor-interface measurement, environmental instrumentation, data acquisition modules, and precision control systems. The four differential inputs are useful when rejecting common-mode noise or measuring bridge-based sensors, while eight single-ended inputs suit systems with several grounded voltage sources. The programmable data rate allows the system architect to balance throughput against the converter's noise performance. For reliable operation, follow the manufacturer datasheet when assigning analog inputs, configuring the digital filter, routing the reference and supply connections, and selecting external input and reference components. Pay particular attention to source impedance and the settling behavior of the digital sinc filter when changing data rates. The four differential inputs must also be connected according to the input-channel architecture shown in the datasheet pin description. This product page combines manufacturer specifications, application guidance, comparison parameters, and practical design considerations for engineers evaluating the MCP3564R-E/ST. It also identifies pin-compatible options while clearly distinguishing parts that reduce channel count or omit the integrated reference, helping selection based on actual measurement requirements.

طلب عرض سعر اتصل بنا
MCP3564RT-E/NC - 24-Bit 153.6kSPS ADC | Microchip
MCP3564RT-E/NC

MCP3564RT-E/NC - 24-Bit 153.6kSPS ADC | Microchip

Microchip MCP3564RT-E/NC is a low-noise 24-bit delta-sigma analog-to-digital converter with four differential or eight single-ended input channels, a maximum programmable data rate of 153.6 kSPS, and a 20-lead UQFN package measuring 3 x 3 mm. A delta-sigma ADC is a category of analog-to-digital converter that uses continuous-time sigma-delta modulation and digital filtering to produce high-resolution conversion results. It belongs to the wider ADC hierarchy, alongside SAR and pipeline converters, and is used when high resolution, low noise, integrated references, and flexible input multiplexing matter more than maximum conversion speed. The MCP3564R family is positioned for precision measurement rather than high-speed waveform capture. The converter provides 24-bit resolution, four differential or eight single-ended channels, and programmable data rates up to 153.6 kSPS. Digital filtering and programmable gain support precise acquisition of low-level analog signals, while the integrated voltage reference reduces external calibration requirements. The SPI interface provides a straightforward connection to microcontrollers, DSPs, and industrial control systems. Its 20-UQFN construction supports compact, high-density analog measurement boards while preserving separate analog and digital supply pins for careful partitioning. Programmable input channels, scan capability, and selectable gain make it possible to combine several sensor inputs into one acquisition channel. The manufacturer product page identifies the device as a low-noise 24-bit delta-sigma ADC with integrated features and programmable data rates. Typical uses include precision sensor interfaces, factory automation, process control, industrial instrumentation, and embedded measurement systems. Four differential inputs can support bridge sensors or differential voltage probes, while eight single-ended inputs suit multiplexed external networks. The SPI-compatible control path simplifies integration with common embedded processors. PCB design should keep analog input traces short and place filtering or anti-aliasing components near the converter. Use a quiet reference and ground arrangement, separate analog and digital supply paths where practical, and follow the manufacturer’s recommended decoupling layout. Allow for the exposed-pad thermal and electrical requirements of the 20-UQFN package. This product page combines the MCP3564R family architecture, package information, sourcing guidance, replacement constraints, and application-oriented design considerations. It is intended to help engineers evaluate the MCP3564RT-E/NC for compact, high-resolution measurement systems without overlooking package, interface, or qualification constraints.

طلب عرض سعر اتصل بنا
MCP3564T-E/NC - 24-Bit, 153.6 kSPS 4-Channel ADC | Microchip
MCP3564T-E/NC

MCP3564T-E/NC - 24-Bit, 153.6 kSPS 4-Channel ADC | Microchip

Microchip MCP3564T-E/NC is a 24-bit low-noise delta-sigma analog-to-digital converter with a maximum data rate of 153.6 kSPS, eight single-ended or four differential inputs, and a 20-UQFN 3 x 3 mm package. It operates from a 2.7 V to 3.6 V supply and communicates through an SPI interface. The converter supports precision measurement of low-frequency analog signals where resolution, integrated noise performance, compactness, and deterministic digital output are important. A delta-sigma ADC is a category of analog-to-digital converter that uses oversampling, a digital filter, and noise shaping to convert an analog input into a high-resolution digital result. It belongs to the broader data-converter hierarchy alongside SAR and pipeline ADCs. Delta-sigma devices are particularly suited to precision acquisition because they can combine high nominal resolution with low noise for slowly changing or band-limited inputs. The MCP3564 combines 24-bit resolution with eight single-ended inputs or four differential inputs. Differential operation rejects common-mode noise and supports bridge-style sensing, while single-ended operation allows several sensors or potentiometer-like signals to share one converter. Its programmable data rate reaches 153.6 kSPS, and the SPI interface provides a straightforward connection to microcontrollers, DSPs, and data-acquisition systems. The low-noise architecture is suited to industrial measurement, sensor interfaces, and precision control systems. The MCP3564 family is designed for low-noise conversion, with the manufacturer identifying the device as a 24-bit sigma-delta ADC. The conversion architecture uses a single sigma-delta modulator, allowing multiple channels to share the modulator under the device's channel configuration. The 20-UQFN package limits board area, while the exposed-pad construction provides a thermal path from the device to the PCB. A stable reference voltage and careful analog-layout practice remain essential to preserve conversion accuracy. Typical uses include factory-floor pressure and temperature acquisition, bridge and transducer measurement, laboratory instrumentation, low-level sensor conditioning, and embedded data-logging systems. Differential inputs are especially useful when the source is referenced to a noisy or floating ground. Single-ended channels simplify systems with multiple independent sensors, although their common-mode rejection is inherently lower than that of a differential connection. Designers should place input filtering and reference-decoupling components close to the converter, preserve a quiet analog ground path, and route digital communications away from sensitive input traces. The 2.7 V to 3.6 V operating range requires compatible supply and logic levels. Because the MCP3564 does not include an internal voltage reference, the external reference network and its bypass capacitor require careful stability and noise analysis. Microchip identifies MCP3564R as the preferred pin-compatible option for new designs because it adds an onboard voltage reference that the MCP3564 lacks. This page combines device specifications, channel and interface guidance, practical application notes, and a clear comparison between the external-reference MCP3564T-E/NC and the preferred MCP3564R architecture.

طلب عرض سعر اتصل بنا
MCP3565T-E/QM - 24-Bit Delta-Sigma ADC | Microchip
MCP3565T-E/QM

MCP3565T-E/QM - 24-Bit Delta-Sigma ADC | Microchip

The Microchip MCP3565T-E/QM is a 24-bit delta-sigma analog-to-digital converter with one analog input channel, a 3 V supply designation, and a 12-pin UQFN package. It is designed for precision signal acquisition where a high-resolution conversion engine and compact surface-mount footprint are required in a space-constrained PCB design. A delta-sigma ADC is an analog-to-digital converter category that uses oversampling, digital filtering, and noise shaping to convert an analog input into a high-resolution digital result. Its role in the broader hierarchy is ADC > data converter > signal-chain IC > semiconductor. This architecture is particularly useful when the target signal bandwidth is much lower than the converter's internal conversion rate, as is common in temperature, pressure, load-cell, industrial-sensor, and precision measurement systems. The MCP3565T-E/QM provides a 24-bit resolution, a single analog conversion channel, and a 3 V operating supply designation. Its single-channel architecture simplifies analog-front-end routing and software configuration when one transducer or sensor must be measured accurately. The 12-pin UQFN package also supports compact layouts, although the exposed-pad and pin-layout requirements in the manufacturer datasheet must be followed during layout and reflow. Delta-sigma conversion provides several practical advantages for low-bandwidth instrumentation. Noise shaping moves quantization noise away from the signal band of interest, while the digital decimation filter rejects high-frequency components. The practical result is high usable resolution without requiring a high-speed successive-approximation ADC architecture. The final conversion rate, input-referred noise, line frequency rejection, and filter configuration should be confirmed from the datasheet before fixing the system gain and update interval. Typical applications include precision temperature sensing, bridge-based pressure and force measurement, industrial process monitoring, portable instrumentation, and low-rate energy or condition monitoring. In each case, the analog signal path must stay short, the reference voltage must remain stable, and the digital interface must be matched to the host processor. A delta-sigma ADC also benefits from averaging and digital correction when absolute measurement accuracy, rather than resolution alone, is the primary objective. When laying out this converter, place input and reference components close to their associated pins, provide a clean analog ground connection, and keep switching or digital return currents away from the input traces. Verify the required decoupling values and exposed-pad connection directly from the Microchip manufacturer datasheet before fabrication. This page combines the converter's confirmed architecture and package characteristics with application-oriented design guidance, specification markers, and procurement context that help engineers evaluate the MCP3565T-E/QM before committing it to a design.

طلب عرض سعر اتصل بنا
MCP3901A0-E/ML - 24-Bit Dual-Channel AFE | Microchip
MCP3901A0-E/ML

MCP3901A0-E/ML - 24-Bit Dual-Channel AFE | Microchip

Microchip Technology MCP3901A0-E/ML is a two-channel analog front end with 16/24-bit delta-sigma analog-to-digital converters, programmable-gain amplifiers, an internal voltage reference, phase-delay compensation, and a 20 MHz SPI-compatible serial interface. The device is offered in a 20-pin 4 x 4 mm QFN package with an exposed pad and reaches up to 91 dB SINAD according to the manufacturer product page. An analog front end is an integrated circuit that converts one or more analog sensor signals into digital measurements. Within the signal-chain hierarchy, the MCP3901A0-E/ML belongs to the AFE and data-converter class, combining input conditioning, conversion, reference generation, and digital communication in one package. Its dual-channel architecture is intended for systems that need accurate measurement from two related analog inputs without requiring two independent converter assemblies. The principal features include two synchronous-sampling delta-sigma ADCs, two internal PGAs, an internal voltage reference, programmable phase-delay compensation, and SPI-compatible communication. The manufacturer describes the converters as supporting 16-bit or 24-bit resolution and using proprietary dithering to reduce idle tones and improve total harmonic distortion. Exact gain settings, input ranges, noise figures, timing limits, and accuracy over temperature should be selected from the manufacturer datasheet and its operating-condition tables. The MCP3901 architecture is suited to precision industrial measurement, battery-powered sensing, process-control instrumentation, and low-bandwidth sensor acquisition. Synchronous delta-sigma conversion is advantageous where low noise and high resolution matter more than very high conversion speed. Phase-delay compensation can simplify synchronization of the two channels, while the internal reference reduces the number of external precision components required for ratiometric or internally referenced measurements. For a practical implementation, place the analog inputs close to their associated pins, keep the input network compact, and route the SPI signals away from noisy switching nodes. The exposed thermal pad should connect to the ground plane with multiple short vias and adequate copper area. Decoupling capacitors should be placed directly at the supply pins in accordance with the manufacturer’s recommended application circuit. This page combines the manufacturer’s device description with package, ordering, sourcing, and application guidance. It also identifies documented family alternatives and highlights the distinction between a true pin-compatible replacement and a related MCP3901 configuration. Final design validation should use the exact Microchip datasheet for electrical limits, pin definitions, timing, filtering, and recommended external circuitry.

طلب عرض سعر اتصل بنا
MCP3901A0-E/SS - Dual 24-Bit 64 kSPS ADC AFE | Microchip
MCP3901A0-E/SS

MCP3901A0-E/SS - Dual 24-Bit 64 kSPS ADC AFE | Microchip

Microchip Technology MCP3901A0-E/SS is a dual-channel analog front end with two synchronous-sampling delta-sigma analog-to-digital converters, selectable 16-bit or 24-bit resolution, a maximum conversion rate of 64 kSPS per channel, and a 20-pin SSOP package. The device includes two programmable-gain amplifiers, an internal voltage reference, phase-delay compensation, and a 20 MHz SPI-compatible serial interface. An analog front end is the precision-measurement stage between real-world analog inputs and a digital controller. It combines conversion, gain control, reference support, and serial communication in one integrated circuit. The MCP3901 belongs to the broader delta-sigma ADC family and is designed for metering and sensor systems where simultaneous dual-channel sampling, high resolution, and serial integration are more important than very high conversion latency. The MCP3901A0-E/SS provides up to 91 dB SINAD and -104 dBc total harmonic distortion. Selectable 16-bit and 24-bit operating modes allow firmware to balance conversion speed, resolution, filtering requirements, and data throughput. Its two programmable-gain amplifiers reduce the need for external signal-conditioning networks, while the internal reference supports a compact and repeatable measurement design. Internally, the MCP3901 uses proprietary delta-sigma converters with a dithering algorithm designed to reduce idle tones and improve total harmonic distortion. The SPI-compatible interface operates at up to 20 MHz, and phase-delay compensation supports measurements where channel timing must be coordinated. The device also supports proprietary dithering for improved signal purity when operating near idle conditions. Typical uses include single-phase energy metering, industrial sensor acquisition, pressure and flow measurement, low-level analog sensing, and instrumentation requiring two synchronized channels. The combination of a 20 MHz serial interface, simultaneous conversion, programmable gain, and selectable resolution makes the device practical for compact measurement systems with limited board area. Designers should follow the manufacturer datasheet for bypass capacitors, input filtering, reference handling, digital-interface timing, and the recommended PCB land pattern. Because the MCP3901A0-E/SS is supplied in a 20-pin SSOP package, component placement and routing should prioritize short analog traces, a clean analog ground connection, and isolation of high-current digital return paths. This product page combines the manufacturer specifications with package information, application guidance, parameter comparisons, and practical design considerations. It is intended to help engineers evaluate the MCP3901A0-E/SS for high-resolution metering and sensor-conversion designs while checking the exact ordering code, pin arrangement, and operating conditions before release to production.

طلب عرض سعر اتصل بنا
MCP3901A0-I/ML - Dual 24-Bit AFE | Microchip Technology
MCP3901A0-I/ML

MCP3901A0-I/ML - Dual 24-Bit AFE | Microchip Technology

The Microchip Technology MCP3901A0-I/ML is a dual-channel analog front end with two synchronous-sampling delta-sigma ADCs, selectable 16-bit or 24-bit resolution, internal programmable-gain amplifiers, an internal voltage reference, phase-delay compensation, and an SPI-compatible serial interface. The device is packaged in a 20-pin 4 x 4 mm QFN and supports analog supply voltages of 2.7 V or 4.5 V up to 5.5 V. An analog front end, or AFE, is the signal-conditioning and conversion interface between a physical analog input and a digital system. In the signal-chain hierarchy, an AFE combines amplifier, converter, reference, and interface functions ahead of a microcontroller or digital controller. The MCP3901 family is designed for dual-channel metering systems in which synchronized sampling, programmable gain, and compact integration simplify energy-meter and sensor-interface designs. Key features include two independent 24-bit delta-sigma conversion channels, internal programmable-gain amplifiers, an internal voltage reference, and up to 91 dB SINAD according to the Microchip product page. A high-speed SPI-compatible interface operates at up to 20 MHz. The industrial-grade ordering code also identifies a surface-mount 20-terminal square QFN package, while the -I/ML package suffix corresponds to the 4 x 4 mm QFN format. The synchronous delta-sigma architecture samples both analog channels in a coordinated manner, which is valuable when measuring two related quantities such as voltage and current in a metering application. Internal gain control reduces the need for external analog gain stages, while the internal reference reduces the number of precision components around the converter. The phase-delay compensation block supports systems where coherent measurements are required. Typical uses include single- and three-phase energy-metering circuits, industrial power monitoring, current-and-voltage sensing, and low-bandwidth sensor acquisition. The two-channel structure allows one AFE to process a voltage input and a current input simultaneously, while the SPI interface allows a host microcontroller to configure conversion parameters and retrieve digital results. When laying out the circuit, place input and reference-related components close to their associated pins, keep analog and digital return currents separated, and use the manufacturer pin-description table to assign tracks. The available power range and exposed thermal-pad requirements should be reviewed against the worst-case analog input, gain, clock, and ambient conditions rather than inferred from the nominal converter specifications alone. This page organizes the manufacturer specifications, package details, application guidance, design considerations, and verified drop-in alternatives for engineers comparing the MCP3901A0-I/ML with other dual-channel metering AFEs. It also distinguishes pin-compatible temperature-grade and resolution-mode variants so replacement decisions are based on measurable device differences.

طلب عرض سعر اتصل بنا
MCP3901A0-I/SS - 24-Bit Dual-Channel AFE | Microchip
MCP3901A0-I/SS

MCP3901A0-I/SS - 24-Bit Dual-Channel AFE | Microchip

The Microchip MCP3901A0-I/SS is a dual-channel analog front end (AFE) with two synchronous sampling delta-sigma analog-to-digital converters, two programmable-gain amplifiers, an internal voltage reference, phase-delay compensation, and a 20 MHz SPI-compatible serial interface. It supports 16-bit and 24-bit resolution, with an output data rate of up to 64 kSPS and up to 91 dB SINAD according to the manufacturer product page. The device is supplied in the MCP3901A0-I/SS 20-pin SSOP package and is designed for energy-metering and precision analog measurement systems. An analog front end is an interface block between real-world sensors and a digital controller. In this case, the MCP3901A0-I/SS performs signal conditioning and conversion internally: the delta-sigma ADCs sample the two input channels synchronously, the PGAs amplify low-level signals, and the internal reference reduces the need for external precision references. The resulting measurements can be transferred to a microcontroller or energy-metering system through the high-speed SPI-compatible interface. The architecture is therefore positioned between analog sensing circuitry and digital data processing. The principal features include two simultaneous sampling channels, selectable 16-bit and 24-bit operating modes, programmable-gain amplification, an internal voltage reference, and a modulator output path. The manufacturer describes the converters as using a proprietary multi-bit delta-sigma architecture with dithering for reduced idle tones and improved total harmonic distortion. The stated performance includes up to 91 dB SINAD and -104 dBc THD up to the 35th harmonic. These characteristics make the device suitable for systems requiring accurate current and voltage measurement in metering equipment. The MCP3901 family combines analog measurement and digital control in one IC. Its SPI-compatible interface allows a host processor to configure the PGAs, select the conversion and oversampling settings, and retrieve digital results. The phase-delay compensation block is useful when both channel measurements must be aligned for real-power calculations. Because the two converters sample synchronously, the device is well suited to current-and-voltage channel pairs where timing consistency affects the calculated energy or power value. Typical applications include single-phase energy meters, industrial power-monitoring equipment, smart-grid measurement, current-sensor signal acquisition, and other low-bandwidth precision measurement systems. The internal reference and PGAs can reduce the external analog component count when the signal range is compatible with the selected gain. The 24-bit resolution is useful for extracting small changes from a larger measurement range, while the 64 kSPS maximum output rate supports higher-rate control or monitoring functions. Designers should pay attention to analog grounding, input filtering, reference behavior, and the relationship between gain, common-mode range, and signal amplitude. The SPI traces should be routed away from high-current switching nodes, and the input network should be designed to limit out-of-band energy before it reaches the delta-sigma converters. The manufacturer datasheet should be used for the complete pin description, electrical limits, timing diagrams, and recommended application circuit. This page combines the manufacturer MCP3901 documentation with distributor information and organizes the part for engineers comparing precision dual-channel AFEs, energy-metering front ends, and SPI-connected measurement ICs.

طلب عرض سعر اتصل بنا
MCP3901T-I/SS - Dual 24-Bit Metering AFE | Microchip
MCP3901T-I/SS

MCP3901T-I/SS - Dual 24-Bit Metering AFE | Microchip

The Microchip Technology MCP3901T-I/SS is a dual-channel analog front end with high-accuracy 16/24-bit delta-sigma analog-to-digital converters, internal programmable gain amplifiers, an internal voltage reference, and phase-delay compensation capable of up to 91 dB SINAD. The device supports a 2.7 V to 5.5 V digital supply, a 4.5 V to 5.5 V analog supply, and is packaged in a 20-pin SSOP measuring approximately 5.30 mm wide. An energy-metering analog front end is an interface IC that converts small, analog sensor signals into high-resolution digital measurements for subsequent processing. Within the measurement hierarchy, the MCP3901 belongs to the analog front end class, integrates delta-sigma ADCs and programmable gain, and serves as a bridge between sensors and a host controller. Its dual-channel architecture allows two measurement channels to be processed within one energy-metering system. The MCP3901 includes 24-bit conversion capability, two measurement channels, programmable gain amplifiers, an internal voltage reference, and phase-delay compensation. These features support accurate acquisition of energy-meter signals while reducing the number of external analog components required. The SPI interface provides a digital connection to a microcontroller or other host processor, while separate analog and digital supply ranges permit system-level power planning. The manufacturer identifies the MCP3901 as a low-cost power-monitoring device and provides a dedicated low-cost power monitor reference design. Its delta-sigma conversion approach is suited to precision measurement rather than high-frequency waveform capture. Phase-delay compensation supports accurate sampling of current and voltage signals when both channels are used within an energy-metering signal chain. Typical applications include single-phase residential energy meters, industrial power monitors, load-management systems, smart-grid sensing equipment, and embedded power-measurement instruments. In these systems, the MCP3901 can digitize voltage and current-related analog inputs before transmitting measurements to a host MCU over SPI. Designers should maintain the specified analog supply range of 4.5 V to 5.5 V and digital supply range of 2.7 V to 5.5 V. The analog and digital return paths, input filtering, reference behavior, and SPI clocking require careful PCB planning to preserve measurement accuracy and prevent switching noise from coupling into sensitive analog inputs. This page combines the manufacturer's core AFE specifications with practical application guidance, interface considerations, and a controlled drop-in comparison. It helps engineers distinguish the MCP3901 from generic multichannel ADCs by focusing on its metering-specific integration, 24-bit resolution, programmable gain, internal reference, and SPI host interface.

طلب عرض سعر اتصل بنا
MCP3903-E/SS - 6-Channel 24-Bit Energy Meter AFE | Microchip
MCP3903-E/SS

MCP3903-E/SS - 6-Channel 24-Bit Energy Meter AFE | Microchip

The Microchip Technology MCP3903-E/SS is a six-channel analog front end (AFE) for high-accuracy energy measurement, with six synchronous-sampling 16/24-bit delta-sigma ADCs, programmable gain amplifiers, an internal voltage reference, phase-delay compensation, and a 10 MHz SPI interface in a 28-pin SSOP package. It accepts a 4.5 V to 5.5 V analog supply and a 2.7 V to 3.6 V digital supply, making it suitable for both metrology and embedded power-monitoring systems. An energy-metering analog front end is an integrated signal-conditioning and conversion block placed between voltage and current sensors and a host processor. The MCP3903 belongs to the ADC, analog front end, and power-management measurement hierarchy. Its six synchronized channels support three-phase measurement, while its delta-sigma converters and internal reference provide the resolution required for accurate real-power and energy calculations. Key features include six synchronous-sampling converters with selectable 16-bit or 24-bit resolution, programmable gain amplifiers, a phase-delay compensation block, an internal voltage reference, and up to 91 dB SINAD. The device also provides a 10 MHz SPI-compatible serial interface for transferring measurement data to a metering microcontroller or energy-metering SoC. Technically, the MCP3903 combines two synchronous-sampling delta-sigma converter cores with three analog channel pairs. This arrangement allows multiple voltage and current inputs to be sampled under common timing conditions, helping preserve the phase relationship required for three-phase energy calculations. The manufacturer identifies the MCP3903 as suitable for three-phase energy measurement, power monitoring, and other systems requiring multiple high-accuracy ADCs. Typical uses include three-phase utility meters, industrial energy monitors, multi-channel power analyzers, building-energy submeters, and embedded systems that measure several voltage and current channels simultaneously. The SPI interface supports integration with Microchip-compatible metering controllers while the internal reference reduces the number of external precision components. A primary design consideration is preserving sensor-channel matching and analog layout quality. Each current and voltage input should use the sensor and filtering network recommended by the manufacturer, while power and ground routing must avoid introducing errors into low-level AFE measurements. Supply bypassing, reference stability, and PCB cleanliness are especially important when the 24-bit operating mode is used. This product page combines verified manufacturer and distributor information, package-specific details, pricing context, and engineering guidance to support component selection, PCB design, and procurement decisions beyond the basic catalog listing.

طلب عرض سعر اتصل بنا
MCP3903-I/SS - 6-Channel 24-Bit Energy AFE | Microchip
MCP3903-I/SS

MCP3903-I/SS - 6-Channel 24-Bit Energy AFE | Microchip

Microchip Technology MCP3903-I/SS is a six-channel analog front end for high-accuracy energy measurement, with six synchronous-sampling 16/24-bit delta-sigma ADC channels, 64 ksps operation, 91 dB SINAD, and a 28-pin SSOP package. It combines two delta-sigma converters with internal programmable-gain amplifiers, an internal voltage reference, phase-delay compensation, and a 10 MHz SPI-compatible interface. An analog front end is an integrated signal-conditioning and conversion block that sits between real-world analog inputs and a digital controller. In the power-management hierarchy, an energy-metering AFE converts voltage and current-sensor waveforms into precise digital measurements. The MCP3903 belongs to this measurement category and is designed around three differential input pairs, making it suitable for three-phase energy monitoring. Key features include six synchronous-sampling channels, selectable 16-bit or 24-bit resolution, and a maximum conversion rate of 64 ksps. According to the manufacturer product information, the device provides up to 91 dB SINAD and -100 dBc total harmonic distortion. Internal programmable-gain amplifiers support analog input conditioning, while the internal voltage reference reduces the external component count in energy-metering designs. The architecture uses three pairs of synchronous-sampling delta-sigma analog-to-digital converters. This arrangement is intended to preserve phase relationships between voltage and current measurements, an important consideration in real-time energy calculations. A phase-delay compensation block compensates for propagation differences in the measurement path, while the internal reference provides a stable conversion basis. Digital results and configuration information are accessed through a high-speed 10 MHz SPI-compatible serial interface. Typical applications include three-phase electricity meters, power-factor monitoring, industrial power-quality instruments, solar and inverter monitoring, and multichannel load analysis. The six-channel architecture allows three voltage and three current measurements to be captured with closely coordinated sampling, reducing the need for multiple discrete converter packages. A critical design consideration is input range and gain selection. The programmable-gain stages must accommodate current-sensor outputs and voltage dividers without clipping, while the selected resolution should match the required metering accuracy. PCB design should minimize analog-trace interference, provide stable reference and supply decoupling, and keep SPI routing away from sensitive current-input nodes. This product page consolidates verified manufacturer and distributor information, compares supported MCP3903 family options, and adds practical selection, sourcing, and PCB guidance. It distinguishes documented performance from parameters that still require verification against the manufacturer datasheet and the completed system design.

طلب عرض سعر اتصل بنا
MCP3903T-E/SS - 6-Channel 24-Bit Energy Meter AFE | Microchip
MCP3903T-E/SS

MCP3903T-E/SS - 6-Channel 24-Bit Energy Meter AFE | Microchip

The Microchip Technology MCP3903T-E/SS is a six-channel analog front end for high-accuracy energy measurement, featuring 24-bit resolution, simultaneous sampling, up to 64 kSPS operation, and a 28-SSOP package. It integrates two delta-sigma analog-to-digital converters, programmable gain amplifiers, an internal voltage reference, phase-delay compensation, and a 10 MHz SPI-compatible serial interface. An energy-metering analog front end converts small voltage-and-current signals from sensing resistors, shunts, and voltage dividers into digital measurements used to calculate active energy, reactive energy, and power. The MCP3903 belongs to the broader ADC and power-management measurement hierarchy: six-channel AFE, multi-channel ADC, delta-sigma ADC, signal-conversion IC, and semiconductor. Its paired conversion architecture supports three-phase metering while preserving synchronous sampling between voltage and current channels. The device provides 91 dB SINAD and -100 dBc total harmonic distortion, supporting accurate extraction of low-level current information from noisy mains-energy signals. Programmable gain amplifiers adapt the front end to different sensor and shunt outputs. A phase-delay compensation block helps align voltage and current measurements, while the internal reference reduces the number of external precision components needed for repeatable results. MCP3903T-E/SS operates from a 4.5 V to 5.5 V analog supply and a 2.7 V to 3.6 V digital supply. The 10 MHz SPI-compatible interface supports fast transfer of conversion and status data to a metering microcontroller. Its 28-SSOP package provides a compact surface-mount format for utility meters, energy monitors, industrial power analyzers, and multi-channel measurement instruments. Typical uses include three-phase electricity meters, single-phase revenue metering, power-quality monitoring, laboratory power analyzers, and embedded energy-management systems. The simultaneous-sampling architecture is especially useful when current and voltage waveforms must remain time-aligned for accurate real and reactive power calculations. A critical design task is preserving analog signal integrity around the six inputs. Keep the analog and digital sections physically separated, route the SPI bus away from sensitive current inputs, and use the recommended filtering and grounding shown in the manufacturer documentation. Confirm the final anti-alias, calibration, and safety-isolation strategy for the target meter class. This page organizes the verified electrical specifications, package details, application guidance, design cautions, and supported family alternatives into a practical engineering reference for selecting and implementing the MCP3903T-E/SS.

طلب عرض سعر اتصل بنا
MCP3903T-I/SS - 6-Channel 24-Bit AFE | Microchip
MCP3903T-I/SS

MCP3903T-I/SS - 6-Channel 24-Bit AFE | Microchip

The Microchip Technology MCP3903T-I/SS is a six-channel analog front end (AFE) built around three pairs of synchronous-sampling delta-sigma analog-to-digital converters, with 24-bit resolution, programmable gain amplifiers, an internal voltage reference, phase-delay compensation, and a 10 MHz SPI-compatible serial interface in a 28-pin SSOP package. Its six channels suit three-phase energy measurement systems that require simultaneous current and voltage acquisition. An analog front end is the precision signal-conditioning and conversion stage between physical sensors or power-system inputs and a digital controller. The MCP3903 belongs to the hierarchy of energy-metering AFE, delta-sigma ADC, data converter, and integrated circuit. Its multi-channel architecture reduces the number of separate converters required when measuring several voltages and currents from a three-phase system. Key features include six synchronous-sampling delta-sigma ADCs, selectable 16-bit or 24-bit operation, a proprietary multi-bit converter architecture, programmable gain amplifiers, and a phase-delay compensation block. The manufacturer specifies 91 dB SINAD and -100 dBc total harmonic distortion. These characteristics are particularly useful when the converter must resolve small AC signals while rejecting harmonic content and nonlinear distortion. The MCP3903 contains three pairs formed from two synchronous-sampling delta-sigma converters. Internal dithering reduces idle tones and improves total harmonic distortion, which supports accurate measurements in metering systems operating with relatively low analog signal levels. The phase-delay compensation block helps align voltage and current measurements, while the internal reference simplifies analog subsystem design and the 10 MHz SPI-compatible interface supports high-speed digital communication with a meter controller. Typical applications include three-phase electricity meters, residential and industrial energy monitoring, power-factor measurement, load-current analysis, and multichannel industrial sensing. Six channels allow a meter design to acquire three voltage signals and three current signals without deploying three unrelated converter subsystems. The same architecture can also support precision power monitoring in automated equipment. A critical design consideration is analog signal conditioning. The input network, current shunt, voltage divider, filtering, and reference connections must preserve the converter's specified dynamic performance and avoid exceeding the analog and digital supply limits. PCB layout should keep sensitive input traces short, isolate them from switching nodes, and provide low-impedance supply connections to minimize measurement error. This product page combines the manufacturer's electrical specifications, package information, pin-compatible family alternatives, application guidance, and PCB-level implementation notes to support faster component selection and first-pass design review.

طلب عرض سعر اتصل بنا
MCP3905A-E/SS - 16-Bit Energy Metering IC | Microchip
MCP3905A-E/SS

MCP3905A-E/SS - 16-Bit Energy Metering IC | Microchip

The Microchip Technology MCP3905A-E/SS is a 16-bit energy-metering analog-to-digital converter IC with two delta-sigma ADCs, programmable gain up to 16, and an integrated voltage reference, packaged in a 24-pin SSOP. It is designed for single-phase energy measurement and supports the IEC 62053 international energy-metering specification. Its measurement inputs and frequency outputs support current and voltage sensing, active-power calculation, and meter calibration. An energy-metering ADC is a specialized data-converter IC that converts analog voltage and current signals into digital measurements while providing the accuracy, linearity, and calibration functions required by an electricity meter. The MCP3905A belongs to the ADC/DAC and power-measurement IC hierarchy, combining precision signal acquisition, internal reference generation, and energy-specific outputs in one device. The MCP3905A incorporates two 16-bit delta-sigma ADCs with programmable gain up to 16, supporting small-shunt measurements across a wide range of input currents. Its integrated voltage reference has ultra-low temperature drift of 15 ppm/°C, helping preserve measurement stability as the meter operates over changing ambient conditions. The device also provides active-real-power pulse output and instantaneous-power-related frequency information according to the manufacturer product description. Typical applications include residential single-phase electricity meters, utility metering modules, energy-monitoring systems, load-control equipment, and industrial power instrumentation. The device is useful when the design needs accurate voltage and current acquisition without relying solely on a general-purpose microcontroller ADC. Designers should carefully review the manufacturer datasheet for input ranges, pin functions, electrical limits, calibration procedures, and application-circuit details. External signal conditioning, filtering, current-shunt selection, voltage-divider design, and PCB layout strongly influence achievable meter accuracy. Pricing and availability should be confirmed against authorized distributors for the current purchasing date.

طلب عرض سعر اتصل بنا
MCP3909ISS - 16-Bit Energy Metering AFE | Microchip
MCP3909ISS

MCP3909ISS - 16-Bit Energy Metering AFE | Microchip

The Microchip Technology MCP3909ISS is a 16-bit energy-metering analog front-end IC with SPI interface, active-power pulse output, and single-phase metering support. The verified product data identifies a 4.5 V to 5.5 V supply range, 2.3 mA supply current, 390 kOhm input impedance, and 0.1% measurement error. It is supplied in a 24-SSOP package, making it suitable for compact single-phase energy-metering designs. An energy-metering AFE is a signal-chain IC that measures voltage and current channels and converts their analog inputs into digital information for energy calculation. In the broader hierarchy, an energy-metering IC belongs to the AFE and power-measurement semiconductor category, where accurate current and voltage acquisition supports utility meters, load monitoring, industrial energy management, and building-energy systems. The MCP3909 is designed around the IEC 62053 international metering specification and also references legacy IEC 1036, IEC 61036, and IEC 687 requirements in the verified data. The MCP3909 combines simultaneous serial access to ADC channels with multiplier output data and a frequency output proportional to average active real power. These features allow a host processor to retrieve measurements while the hardware provides a convenient active-power pulse indication. The 16-bit ADC architecture is intended for metering applications where measurement resolution and energy accuracy are more important than low-cost general-purpose signal acquisition. Typical uses include single-phase utility meters, residential energy monitors, industrial submeters, appliance energy measurement, and embedded power-monitoring equipment. In these systems, the AFE accepts voltage and current information, performs analog-to-digital conversion, and supplies measurement data through its serial interface. The active-power output can provide a low-frequency measurement signal for meter calibration, energy accumulation, or system monitoring. The principal design considerations are input filtering, calibration, reference stability, signal integrity, and correct implementation of the current and voltage channels. Designers should follow the manufacturer datasheet for the exact pin functions, recommended external components, analog input limits, digital interface timing, and calibration procedure. The verified web data confirms the 24-SSOP package and tube packaging information, while some detailed electrical limits and pin-level details require datasheet confirmation. This page combines verified manufacturer and distributor information with application guidance and design considerations. It also identifies the MCP3909 as a single-phase 24-SSOP energy-metering IC with SPI connectivity, active-power pulse output, a 16-bit ADC, and support for IEC 62053-oriented metering designs.

طلب عرض سعر اتصل بنا
MCP3911A0-E/ML - 24-Bit Dual-Channel AFE | Microchip
MCP3911A0-E/ML

MCP3911A0-E/ML - 24-Bit Dual-Channel AFE | Microchip

The Microchip MCP3911A0-E/ML is a 24-bit, dual-channel analog front end for energy-metering and precision analog measurement systems. It operates from a 2.7 V to 3.6 V supply, provides two simultaneous-sampling delta-sigma ADCs, and is housed in a 20-QFN package measuring 4 x 4 mm. The device combines two programmable gain amplifiers with a 20 MHz SPI-compatible serial interface. An analog front end, or AFE, integrates the signal-conditioning and conversion functions needed between a physical sensor and a digital controller. The MCP3911 belongs to the energy-metering AFE hierarchy: dual-channel delta-sigma ADC, programmable gain amplifier, voltage reference, phase compensation, and serial digital interface. This integration reduces external analog circuitry while preserving simultaneous measurement of two related input channels. Key features include 24-bit conversion resolution, a 1.2 V internal reference with a 9 ppm/°C temperature coefficient, and phase-delay compensation with 1 µs resolution. The two PGAs condition low-level sensor inputs before conversion, while the 20 MHz SPI-compatible interface supports efficient communication with a host microcontroller. The distributor description identifies the MCP3911A0-E/ML as an 8.9 mW, 20-QFN energy-metering AFE. Internally, the MCP3911 uses two synchronous-sampling delta-sigma ADCs to acquire both channels at the same time. Simultaneous sampling helps cancel common-mode disturbances and avoids time skew when comparing two quantities such as voltage and current. The phase compensation block, modulator outputs, calibration registers, reference selection, and digital gain and offset controls support accurate energy calculations and coordinated system calibration. Typical uses include single-phase energy meters, industrial power monitors, smart-grid measurement equipment, and embedded metering systems. Its dual-channel architecture is especially useful when one channel senses voltage and the other senses current. The 3.3 V supply requirement also aligns the AFE with 3.3 V microcontroller and digital-control environments where external signal conditioning should be minimized. Designers should select input and reference components according to the manufacturer’s application circuit, maintain the specified analog and digital layout, and account for the AFE’s supply and common-mode limits. When accuracy depends on current-sensor gain, the programmed PGA setting, reference voltage, calibration coefficients, and system offset must be evaluated together rather than optimized independently. This page combines the manufacturer’s device capabilities with practical metering considerations, structured alternatives, interface guidance, and a parameter-focused comparison. It is intended to help engineers determine whether the MCP3911A0-E/ML fits a compact, dual-channel, 24-bit energy-metering design before committing to a PCB footprint.

طلب عرض سعر اتصل بنا
MCP41010-I/P - 8-Bit 10kΩ SPI Digital Potentiometer
MCP41010-I/P

MCP41010-I/P - 8-Bit 10kΩ SPI Digital Potentiometer

The Microchip Technology MCP41010-I/P is a single-channel, 8-bit digital potentiometer with 10 kΩ end-to-end resistance, 256 taps, and an SPI serial interface in an 8-pin PDIP package. It replaces a mechanical potentiometer with a digitally controlled resistance whose wiper position varies linearly according to commands written over the serial bus. A digital potentiometer is a solid-state variable resistor whose effective tap position is stored in an internal register. The MCP41010 belongs to the digital potentiometer, programmable resistor, interface IC, and power-management-adjacent control-device hierarchy. Its SPI interface allows a microcontroller to adjust gain, offset, current, voltage, or resistance without mechanical wear, while preserving a familiar three-terminal potentiometer arrangement. The device provides 256 wiper positions, giving an 8-bit command resolution and a linear relationship between the programmed code and resistance. Its 10 kΩ end-to-end resistance is suitable for signal-conditioning, current-control, and calibration networks where a compact, digitally adjustable resistance is required. The MCP41010 is controlled through standard SPI serial commands and supports integration with embedded control systems. Because the MCP41010 has only one potentiometer channel and one wiper, it is intended for single-axis adjustment rather than multi-channel gain or timing control. Its SPI architecture makes it suitable where board space is constrained and repeated electronic recalibration is more valuable than the mechanical travel and resolution of a conventional potentiometer. Applications include sensor calibration, programmable gain, current feedback, test equipment, audio attenuators, and embedded control systems. Designers should treat the terminals A, B, and W as the functional equivalent of a potentiometer while accounting for the internal wiper resistance and finite bandwidth. Place the device close to the controlled signal path, use a defined ground reference, and keep sensitive SPI routing away from high-current switching nodes. Software should limit wiper movement when a mechanical load could otherwise stall the internal wiper. This page combines the manufacturer's product information with practical application guidance, interface comparisons, and design notes. It helps engineers assess the MCP41010-I/P as an SPI-controlled 10 kΩ digital resistor for embedded analog-control designs, while separate handling of lifecycle, compliance, and sourcing details keeps the page suitable for technical evaluation and quotation.

طلب عرض سعر اتصل بنا
MCP41050-E/P - 50k SPI Digital Potentiometer | Microchip
MCP41050-E/P

MCP41050-E/P - 50k SPI Digital Potentiometer | Microchip

Microchip Technology MCP41050-E/P is a single-channel, 8-bit digital potentiometer with 50 kΩ end-to-end resistance, 256 wiper positions, and a 3-wire SPI interface in an 8-pin PDIP package. It operates from 2.7 V to 5.5 V and provides a software-programmable resistance or attenuation function without a mechanical wiper. A digital potentiometer is a programmable resistor whose effective tap position is stored as an 8-bit code. The MCP41050-E/P places one digitally controlled resistor between two analog terminals and presents a wiper output. This digital potentiometer belongs to the MCP41XXX family of single-channel, 256-position devices and sits within the broader category of passive analog components controlled by interface ICs. The principal benefits are 8-bit resolution, 256 discrete wiper settings, and SPI-based control. The wiper position varies linearly with the code written to the device, making the MCP41050-E/P useful for programmable gain, attenuation, bias adjustment, threshold setting, sensor calibration, and feedback-loop compensation. Its 50 kΩ resistance provides a practical balance between divider precision, signal range, and component loading. The device supports a 2.7 V to 5.5 V supply range and uses a serial interface that allows the wiper code to be updated by a host controller. Its maximum integral nonlinearity is specified as ±1 LSB, while the 256-position architecture corresponds to 8-bit resolution. The -E device variant is supplied in a through-hole PDIP package, making it convenient for prototypes, educational boards, and assemblies that favor socketed or leaded components. Typical applications include audio volume and attenuation control, sensor signal conditioning, programmable reference circuits, laboratory equipment, industrial control modules, and microcontroller-based instrumentation. Because the resistance changes under digital control, the part can eliminate electromechanical potentiometers where reliability, repeatability, or remote adjustment matters. When laying out a circuit, route the SPI signals away from sensitive analog inputs, keep the wiper connection short, and treat terminal resistance, wiper impedance, and the load connected to the wiper as part of the signal-path design. Confirm the programmed resistance against the required transfer function, because the ideal 8-bit relationship does not remove the effects of finite output resistance and load error.

طلب عرض سعر اتصل بنا
MCP41050-I/P - 50kOhm 8-Bit SPI Digital Potentiometer | Microchip
MCP41050-I/P

MCP41050-I/P - 50kOhm 8-Bit SPI Digital Potentiometer | Microchip

The Microchip Technology MCP41050-I/P is a single-channel, 8-bit digital potentiometer with 50 kΩ end-to-end resistance, 256 SPI-addressable tap positions and a linear wiper taper, housed in an 8-pin PDIP package. It operates from a 2.7 V to 5.5 V supply voltage and supports SPI clock modes 0,0 and 1,1. A digital potentiometer is a solid-state, actively controlled substitute for a mechanical trimmer potentiometer. Instead of a sliding wiper driven by a screw or shaft, it uses an internal resistor string terminated by an electrically driven wiper that is positioned by a serial command. In the broader component hierarchy it sits above the passive potentiometer and alongside the resistor network, and it belongs to the family of programmable passives used to trim, calibrate or attenuate a signal without physical adjustment. Key features of the MCP41050 include 256 taps per potentiometer, ±1 LSB maximum integral nonlinearity and differential nonlinearity, a low-power serial interface, and an end-to-end resistance of 50 kΩ. The part belongs to the MCP41XXX/MCP42XXX family, which offers single and dual channel versions in 10 kΩ, 50 kΩ and 100 kΩ resistance options, so the same firmware and board pattern can be reused across different trim ranges. The device uses a serial peripheral interface (SPI) compatible command structure for writing the wiper register, which lets a microcontroller set the tap position in a single byte transfer. The wiper position is held in a volatile register, meaning the last programmed value is retained while power is applied but returns to a defined state after power cycling. The MCP41XXX device is a single-channel part offered in 8-pin PDIP and SOIC packages, with outstanding AC and DC characteristics for audio and instrumentation signal paths. Typical applications include audio volume and gain control, sensor amplifier calibration, programmable filter and threshold adjustment, and general instrumentation trimming where a fixed value must be set by firmware rather than by hand. Because the wiper position is controlled in software, calibration data can be stored in non-volatile memory and reloaded on every power-up. When designing with the MCP41050-I/P, remember that the wiper is not a buffered output: place a buffer or a suitable feedback resistor network after the wiper pin when driving a high-impedance or capacitive load. Also allow for the potentiometer's own resistance in the signal path and keep the SPI traces short, since the interface is sensitive to ringing on fast clock edges. This page brings together device specifications, pin-level detail, package-level alternatives and practical design notes that go well beyond the basic parameter table, helping engineers qualify the MCP41050-I/P for new designs without repeated datasheet searching.

طلب عرض سعر اتصل بنا
MCP41100-I/P - 100kΩ 8-Bit SPI Digital Potentiometer | Microchip
MCP41100-I/P

MCP41100-I/P - 100kΩ 8-Bit SPI Digital Potentiometer | Microchip

Microchip Technology MCP41100-I/P is a single-channel, 8-bit digital potentiometer with a 100 kΩ end-to-end resistance, 256 wiper positions, and a 3-wire SPI serial interface in an 8-pin PDIP package. The wiper position varies linearly with the value written to the wiper register, allowing an external controller to adjust resistance without a mechanical potentiometer. A digital potentiometer is a solid-state resistor whose effective resistance or voltage-divider tap is controlled electronically. The MCP41100 belongs to the digital potentiometer hierarchy, combining a resistor array, switch matrix, wiper circuitry, and serial interface in one integrated circuit. This eliminates moving contacts, improves repeatability, and supports remote configuration through a microcontroller or embedded control system. The MCP41100-I/P provides 8-bit resolution across 256 positions, a 100 kΩ nominal end-to-end resistance, and SPI control. Its linear wiper characteristic simplifies calculations when the device is used as a voltage divider, a programmable attenuation element, or an adjustable resistance in control and measurement circuits. The 8-bit interface also allows the controller to select a position using an 8-bit command word. The device uses a 3-wire serial interface compatible with the SPI communication format identified by Microchip for the MCP4XXXX family. The target MCP41100-I/P is supplied in the 8-pin PDIP package, allowing through-hole assembly and prototyping. For compact production boards, the manufacturer also offers MCP41100 variants in surface-mount packages, but those package variants require corresponding land-pattern and assembly changes. Typical applications include firmware-controlled gain adjustment, sensor calibration, programmable dividers, test and measurement front ends, industrial control boards, and educational prototyping systems. An MCU can update the wiper position while the analog circuit remains electrically isolated from mechanical wear and repeated adjustment. When laying out the circuit, treat the two resistor terminals as analog nodes and keep the SPI traces away from sensitive wiper and divider outputs. Confirm the programmed endpoint behavior and usable wiper range in the application because digital potentiometers may exhibit endpoint tolerance and wiper nonlinearity. Confirm the exact voltage, current, and temperature limits against the manufacturer datasheet before committing the design to production. This page combines the manufacturer device description, exact MPN package information, interface characteristics, pin-compatible family candidates, and practical design guidance. It also distinguishes true package-compatible alternatives from surface-mount and other-package variants that cannot replace MCP41100-I/P without PCB changes.

طلب عرض سعر اتصل بنا
MCP4162-503E/MS - 50kΩ SPI Digital Potentiometer | Microchip
MCP4162-503E/MS

MCP4162-503E/MS - 50kΩ SPI Digital Potentiometer | Microchip

The Microchip Technology MCP4162-503E/MS is a single, non-volatile 8-bit digital potentiometer with a 50kΩ end-to-end resistance, 257 wiper positions, a four-wire SPI interface, and an 8-pin MSOP package. It combines a digitally controlled resistor with EEPROM-backed wiper storage, allowing a microcontroller to set and retain an analog resistance without a mechanical adjustment. A digital potentiometer is a programmable passive-network component that replaces a conventional mechanical potentiometer. Its internal resistor array provides two terminals and a wiper terminal, while an external controller moves the wiper through discrete codes. Digital potentiometers belong to the broader analog-control IC and programmable-resistor categories and are commonly used for gain, offset, filtering, sensing, and calibration circuits. The MCP4162-503E/MS provides 257 selectable wiper positions, corresponding to 8-bit control resolution and a nominal 50kΩ resistance. Its SPI-compatible serial interface supports digital setting from a host controller, while the non-volatile memory preserves the programmed wiper value for subsequent power cycles. The device is identified by verified distributor data as a single-circuit digital potentiometer in an 8-MSOP package. The -503E/MS ordering code denotes the 50kΩ resistance option and the MS package variant. The E designation is associated with the extended operating-temperature option in common Microchip digital-potentiometer naming, although the exact temperature limits and electrical tolerances should be confirmed in the manufacturer datasheet before production release. The part uses a four-wire SPI interface with chip select, serial clock, serial data input, serial data output, and power pins in the 8-pin package. Typical applications include programmable amplifier gain stages, sensor-signal conditioning, audio volume or attenuation control, industrial calibration networks, and embedded systems requiring persistent control settings. Because the MCP4162-503E/MS stores its wiper value in non-volatile memory, it is useful when the system must restart without losing a calibration or user-adjustment value. Designers should verify the complete pinout, electrical limits, wiper resistance, memory endurance, and timing characteristics against the Microchip MCP4162 datasheet. Place the device close to the controlled analog network, keep SPI traces away from sensitive high-impedance nodes, and confirm that the selected resistance and wiper current suit the application. This product page combines verified distributor information, package data, replacement guidance, and practical selection notes for engineers evaluating the MCP4162-503E/MS.

طلب عرض سعر اتصل بنا