AD7730BRUZ - 24-Bit Sigma-Delta Bridge Transducer ADC | Analog Devices
MPN: AD7730BRUZ ✓ نشطAD7730BRUZ نظرة عامة
An analog front end (AFE) is the signal-conditioning stage that sits between a sensor and a digital processor. In bridge-sensor applications the AFE must amplify microvolt-level signals, reject 50 Hz/60 Hz line noise, and present a clean digital word to the MCU or DSP. The AD7730 combines a precision programmable-gain instrumentation front end, a 24-bit sigma-delta modulator, and a digital low-pass filter on a single die, eliminating the external IA and ADC pair that older weigh-scale designs required. Architecturally it belongs to the wider ADC family -> sigma-delta ADC -> 24-bit ADC -> precision data acquisition IC -> signal chain.
Key features include 5 nV/C offset drift, 2 ppm/C gain drift, greater than 150 dB line-frequency rejection, and four unipolar input ranges (0 to +/-10 mV, +20 mV, +40 mV, +80 mV) plus four bipolar ranges (+/-10 mV, +/-20 mV, +/-40 mV, +/-80 mV). Two buffered differential inputs and a differential reference input allow direct connection to a four-wire bridge. On-chip self-calibration and system-calibration routines remove offset and gain error after PCB assembly.
Typical applications include electronic weigh scales, load-cell transmitters, pressure transducers, and industrial process-control front ends. The TSSOP-24 footprint also makes it a fit for medical infusion pumps and force-measurement instrumentation where board area is constrained and a true 24-bit noise-free conversion is required.
When designing with the AD7730BRUZ, separate the analog AVDD and digital DVDD supplies and decouple each pin with 100 nF ceramic plus a 10 uF bulk capacitor. Use a low-noise reference such as the ADR03 / ADR420 and keep the bridge excitation current return path close to the analog ground plane.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
بدائل مباشرة لـ AD7730BRUZ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع AD7730BRUZ (نفس عامل الشكل والبصمة) — يختلف في Package, Resolution, Number of Channels, Operating Temperature, Supply Voltage.
AD7730BRUZ-REEL7
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AD7730LBRUZ
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
AD7730BRUZ الحدود القصوى والخصائص الكهربائية
| Manufacturer | Analog Devices |
| Part Number | AD7730BRUZ |
| الوظيفة | 24-bit sigma-delta analog front end for bridge transducers |
| الدقة | 24-bit (up to 230,000 counts peak-to-peak) |
| Number of Channels | 1 differential (2 buffered inputs) |
| جهد التغذية | +4.75 V to +5.25 V (single +5 V) |
| Typical Power Dissipation | 125 mW |
| Analog Input Ranges (Unipolar) | 0 to +10 mV, 0 to +20 mV, 0 to +40 mV, 0 to +80 mV |
| Analog Input Ranges (Bipolar) | +/-10 mV, +/-20 mV, +/-40 mV, +/-80 mV |
| Offset Drift | 5 nV/C (max) |
| Gain Drift | 2 ppm/C (max) |
| Line-Frequency Rejection | >150 dB |
| Reference Input | Differential |
| Digital Interface | Serial, compatible with microcontrollers and DSPs (3-wire mode) |
| Calibration | On-chip self-calibration and system calibration |
| العلبة | 24-lead TSSOP (RU-24) |
| نوع التركيب | Surface Mount |
| درجة حرارة التشغيل | -40 C to +85 C |
| حالة RoHS | Compliant |
| Lead-Free | Yes |
| AEC-Q100 | Not qualified (industrial grade only) |
تكوين أطراف AD7730BRUZ
| دبوس 1 | SCLK — Serial clock input |
| دبوس 2 | DOUT — Serial data output |
| دبوس 3 | DIN — Serial data input |
| دبوس 4 | CS — Chip select, active low |
| دبوس 5 | RESET — Reset input, active low |
| دبوس 6 | MODE — Mode select for filter/notch |
| دبوس 7 | A0 — Register address select |
| دبوس 8 | STANDBY — Standby input, active high |
| دبوس 9 | SYNC/~RDY — Synchronization / ready output |
| دبوس 10 | DGND — Digital ground |
| دبوس 11 | DVDD — Digital +5 V supply |
| دبوس 12 | AVDD — Analog +5 V supply |
| دبوس 13 | REF IN+ — Differential reference input positive |
| دبوس 14 | REF IN- — Differential reference input negative |
| دبوس 15 | AGND — Analog ground |
| دبوس 16 | AIN1+ — Analog input 1 positive |
| دبوس 17 | AIN1- — Analog input 1 negative |
| دبوس 18 | AIN2+ — Analog input 2 positive |
| دبوس 19 | AIN2- — Analog input 2 negative |
| دبوس 20 | ACAL — Calibration capacitor |
| دبوس 21 | ACAP — Analog filter capacitor |
| دبوس 22 | ACOM — Analog common |
| دبوس 23 | NC — Not connected (per datasheet) |
| دبوس 24 | NC — Not connected (per datasheet) |
التطبيقات النموذجية
AD7730BRUZ مناسب لـ 6 التطبيقs: Electronic Weigh Scale / Load Cell, Pressure Transmitter / Process Control, Force Measurement and Load Monitoring, Medical Infusion Pump / Dosing System, Industrial Process Control Analog Input Module, Battery-Powered Weigh Indicator.
Electronic Weigh Scale / Load Cell
The AD7730BRUZ is the canonical bridge-AFE for single-channel bench and floor scales. Its 5 nV/C offset drift and 2 ppm/C gain drift hold calibration over the -40 C to +85 C industrial range, while >150 dB line-frequency rejection removes 50 Hz/60 Hz mains pickup. Placed between a 350 ohm 2 mV/V load cell and a microcontroller, with the bridge excitation shared with the reference input, it produces a noise-free 16-bit reading at the 10 mV range and is calibrated on power-up by the on-chip self-calibration routine. Compared with discrete INA + 24-bit ADC solutions, the integrated AFE drops 4-6 components and the calibration routine eliminates the manual trimpot.
موصى به
Pressure Transmitter / Process Control
Industrial pressure transmitters using strain-gauge or piezoresistive bridges benefit from the AD7730BRUZ's bipolar +/-10 mV to +/-80 mV input ranges and differential reference input. The bipolar ranges accommodate ratiometric measurements where the bridge output swings around the excitation voltage. Power dissipation of 125 mW is acceptable inside a loop-powered 4-20 mA transmitter head with proper thermal layout. The on-chip system-calibration routine lets the host MCU run a one-touch field calibration against a dead-weight tester, while 2 ppm/C gain drift keeps the 0.1 percent FS accuracy budget intact across process temperature swings.
موصى به
Force Measurement and Load Monitoring
Force plates, force-test rigs, and machine-tool load-monitoring systems need sub-microvolt resolution at low update rates, which is exactly the AD7730BRUZ's niche. The TSSOP-24 footprint drops onto the same PCB as a strain-gauge instrumentation amp frontend, eliminating a separate IA stage. Combined with chop mode and the digital filter's deep first notch, the part provides >20 bits of effective resolution in a 50 Hz or 60 Hz environment. Engineers should reserve 10 mm of board edge around the bridge traces and route the analog AVDD separately from the digital DVDD to preserve 5 nV/C offset drift.
موصى به
Medical Infusion Pump / Dosing System
Medical infusion pumps measure small differential pressures across a disposable flow element, and the AD7730BRUZ's 24-bit resolution with low input ranges is well matched to single-channel pressure sensing. The on-chip calibration supports periodic in-situ re-zeroing during the pump's self-test cycle, and the -40 C to +85 C industrial range covers the thermal envelope of an infusion-pump enclosure. Note that the AD7730BRUZ is NOT AEC-Q100 qualified and is not aimed at life-support devices, so it suits the dosing subsystem rather than the patient-isolation barrier.
موصى به
Industrial Process Control Analog Input Module
Process-control analog input modules that interface to load cells, weight feeders, and tank-weighing systems use the AD7730BRUZ as a single-channel 24-bit front end. Its serial interface is directly compatible with industrial microcontrollers and DSPs, and the TSSOP-24 footprint fits a standard 4 mm x 4 mm analog-frontend island. Differential reference input rejects ground-loop noise common in plant environments, and the on-chip digital filter's programmable first-notch frequency lets the same module serve 50 Hz and 60 Hz regions without firmware changes.
موصى به
Battery-Powered Weigh Indicator
Portable battery-powered weigh indicators for parcel scales, fishing scales, and handheld force gauges use the AD7730LBRUZ (the lower-power sibling of the AD7730BRUZ) at the heart of the analog section. The standard AD7730BRUZ with 125 mW dissipation is used where line power is available, while the AD7730L variant enables multi-month battery life. The same TSSOP-24 footprint and pinout let designers drop either die on the same PCB and select the variant at procurement, preserving one design across two power budgets.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ AD7730BRUZ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | AD7730BRUZ-REEL7 | AD7730LBRUZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-24 | TSSOP-24 | TSSOP-24 |
| Resolution | 24-bit, 230k counts p-p | 24-bit, 230k counts p-p | 24-bit, lower throughput |
| Input Ranges | +/-10 to +/-80 mV, 0 to +80 mV | +/-10 to +/-80 mV, 0 to +80 mV | +/-10 to +/-80 mV, 0 to +80 mV |
| Offset Drift | 5 nV/C | 5 nV/C | 5 nV/C |
| Gain Drift | 2 ppm/C | 2 ppm/C | 2 ppm/C |
| Line Rejection | >150 dB | >150 dB | >150 dB |
| Supply Voltage | +4.75 V to +5.25 V | +4.75 V to +5.25 V | +4.75 V to +5.25 V |
| Power Dissipation | 125 mW | 125 mW | Lower (AD7730L variant) |
أبرز الفروقات
- Only TSSOP-24 member of AD7730 family with full +125 mW throughput grade (مقابلAD7730LBRUZ)
- Industrial -40 C to +85 C specification (مقابلAD7730CBRUZ)
- Same-brand pin-compatible lower-power alternative exists in same package (مقابلAD7730LBRUZ)
ملاحظات التصميم
Decouple AVDD and DVDD separately. Each analog pin gets a 100 nF ceramic capacitor placed within 5 mm of the pin plus a shared 10 uF bulk capacitor. Use a low-noise LDO such as the ADP150 to derive AVDD from a clean +5 V rail, and isolate the digital DVDD with a ferrite bead to keep digital switching noise out of the analog modulator.
Route the differential bridge traces (AIN1+, AIN1-, AIN2+, AIN2-, REF IN+, REF IN-) as a tightly coupled pair with 0.15 mm spacing and a continuous ground plane underneath. Guard the bridge traces with grounded copper on both sides of the differential pair, and avoid running digital traces (SCLK, DOUT, DIN) parallel to the analog traces to preserve the 5 nV/C offset drift budget.
Do not bypass the on-chip calibration routine. Run self-calibration at power-up and after every gain change, and run system-calibration once with the bridge installed to remove the system's zero-weight offset. Connecting ACAL and ACAP with the wrong capacitor value (datasheet recommends 0.1 uF) will cause the calibration to fail and the part will appear stuck at full-scale output.
Keep the bridge excitation current return path close to the analog ground plane. Use a Kelvin connection to the load cell so the voltage-sensing taps do not carry the bridge excitation current, which would otherwise introduce 2-5 ppm/C gain drift beyond the part's own 2 ppm/C specification.
معلومات الامتثال
Per Analog Devices product page, AD7730BRUZ is RoHS compliant and lead-free. Not AEC-Q100 qualified; choose AEC-Q100 parts for automotive. Halogen-free status not stated on the verified product page.
