Analog Devices

ADM4854AR - 115kbps Low-EMI RS-485 Transceiver | Analog Devices

MPN: ADM4854AR ✓ نشط
5 V Vdss 5 uA Id RS-485 and RS-422 Rds(on) 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

ADM4854AR نظرة عامة

Analog Devices ADM4854AR is a 5 V, slew-rate-limited differential line transceiver for RS-485 and RS-422 communication networks, with a maximum data rate of 115 kbps in an 8-pin SOIC package. The device supports half-duplex and full-duplex data communication, uses reduced slew rates to limit electromagnetic interference, and includes true fail-safe receiver inputs.

An RS-485/RS-422 interface transceiver is an interface IC that converts logic-level signals into balanced differential line signals and reconstructs logic-level data from a differential bus. These transceivers occupy the physical-layer portion of a multipoint industrial communication network. Balanced signaling improves noise immunity over long cable runs, while the low-EMI slew-rate characteristic reduces reflected and radiated energy when the data rate is modest.

The ADM4854 family supports several data-rate and duplex combinations. The ADM4854 position corresponds to the 115 kbps option, making it appropriate for slow industrial-control links rather than high-speed backplane or automation networks. Its reduced slew rate is the defining feature: slower edge rates limit EMI while retaining enough bandwidth for conventional RS-485 equipment. True fail-safe receiver inputs maintain a defined receiver state when the bus is idle or a driver is disconnected.

Analog Devices describes the ADM4854 as a single-chip differential transceiver intended for multipoint bus transmission lines. Operating from 5 V supports integration with conventional 5 V logic systems, while the differential bus interface supports noise-tolerant field-bus communication. The 8-pin SOIC construction allows direct placement in conventional through-hole or mixed-technology assemblies when the appropriate assembly variant is selected.

Typical uses include industrial instrumentation, building-control equipment, process monitoring, factory automation, and remote sensor interfaces. Because the 115 kbps rate is deliberately restrained, the part is particularly suitable for low-to-moderate data volumes, supervisory signals, and legacy RS-485 installations where minimizing electromagnetic emissions is more important than maximizing throughput.

Design the bus with correct differential routing, controlled return paths, appropriate termination, and protection for the target installation. The reduced slew rate helps with EMI, but cable length, topology, grounding, and surge exposure still determine reliable operation. Verify the transceiver’s drive and receiver configuration against the selected ADM4854 ordering option before fixing the PCB.

This page consolidates the ADM4854 family positioning, interface characteristics, drop-in considerations, package information, and practical RS-485 design guidance into an engineer-focused selection reference.

بدائل مباشرة لـ ADM4854AR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ADM4854AR (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Package, Product Type.

Analog Devices
Maximum Data Rate: 500 kbps
Package: 8-lead SOIC
Product Type: RS-485/RS-422 differential line transceiver
قارن مع ADM4854AR →

ADM4854ARZ

✅ بديل مباشر
📦 8-SOIC
Same ADM4854 family and 8-SOIC package; ordering suffix must be checked for qualification and configuration differences

📋 بديل مرجعي (غير موجود في الكتالوج)

ADM4854AR المواصفات

Product Type Differential line transceiver
Supported Standards RS-485 and RS-422
جهد التغذية 5 V
Maximum Data Rate 115 kbps
Duplex Modes Half-duplex and full-duplex
Slew Rate Reduced for low EMI
Receiver Fail-Safe True fail-safe receiver inputs
Maximum Supply Current 5 uA
العلبة 8-pin SOIC
Package Designation PDSO8
نوع التركيب Surface mount
Signal Type Differential
Network Topology Multipoint bus transmission lines
Communication Family ADM4850 through ADM4857

دليل تكوين أطراف ADM4854AR pdso8

تكوين الأطراف لـ ADM4854AR (حزمة pdso8). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة pdso8 لـ ADM4854AR

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM4854AR.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ADM4854AR مناسب لـ 6 التطبيقs: Industrial Process Instrumentation, Building Control Networks, Factory Automation Equipment, Remote Environmental Sensors, Security and Access Control, Communication and Networking Interfaces.

🏭

Industrial Process Instrumentation

The ADM4854AR fits slow industrial process-instrumentation links that operate on RS-485 at rates up to 115 kbps. Its differential line interface supports reliable communication between a controller and remote transmitters over cables running through electrically noisy production areas. The reduced slew rate helps limit high-frequency EMI generated by the transmitter, while true fail-safe receiver inputs help the controller interpret an idle or disconnected bus predictably. A 5 V supply also integrates naturally with conventional controller logic. In practice, the application remains sensitive to grounding, termination, surge protection, and the number of loads on the bus.

🧩

Building Control Networks

The ADM4854AR is appropriate for RS-485 building-control networks carrying supervisory commands, status reports, and sensor data at up to 115 kbps. Buildings commonly connect HVAC controllers, access-control equipment, lighting panels, and environmental sensors across long interior cable runs. The device’s differential receiver improves common-noise rejection, while the reduced slew rate helps contain radiated emissions in occupied spaces and near sensitive electronics. The 115 kbps limit makes this device more appropriate for supervisory control than high-bandwidth building systems. Pair it with correctly placed termination, protective surge components, and a defined grounding strategy.

🏭

Factory Automation Equipment

The ADM4854AR can connect legacy factory automation equipment using an EIA RS-485 bus. At 115 kbps, it is well suited to machine status, parameter transfer, alarms, and low-bandwidth sensor traffic rather than high-speed motion-control data. The half-duplex and full-duplex family options allow it to be integrated according to the bus architecture selected for the exact ADM4854AR configuration. Reduced edge rates reduce EMI on factory wiring, and true fail-safe behavior improves logic definition when a node releases the bus. System reliability still depends on isolated grounds, controlled cable routing, termination, and industrial surge protection.

🧩

Remote Environmental Sensors

The ADM4854AR supports low-rate RS-485 links for temperature, humidity, air-quality, and environmental monitoring nodes. Such sensors usually exchange compact measurement packets or configuration commands, making the 115 kbps limit more than adequate while favoring reduced EMI. The 5 V transceiver operation is useful in instrument clusters that already use a common low-voltage bus. True fail-safe receiver inputs provide predictable behavior when a sensor node is disconnected or powered down. For long outdoor or plant installations, engineers should still add surge and ESD protection, verify grounding, and keep sensor cables away from high-energy switching conductors.

🎥

Security and Access Control

The ADM4854AR can support RS-485 communication among access-control readers, door controllers, alarm panels, and other low-bandwidth security equipment. The differential interface is useful for door and perimeter cabling where nodes may be separated from the central controller, while the 115 kbps rate is appropriate for identity events, status changes, and configuration traffic. Reduced slew rate helps limit EMI in buildings containing sensitive electronic equipment. A robust deployment requires isolation and surge protection at exposed cable entries, correct bus termination, and a protocol strategy that prevents one inactive node from disturbing the rest of the network.

🌐

Communication and Networking Interfaces

The ADM4854AR can serve as the physical RS-485 interface within industrial communication equipment, gateways, and data concentrators. It is appropriate for supervisory links and legacy equipment that exchange modest amounts of data at up to 115 kbps. Differential signaling supports reliable operation across cabinet-to-cabinet wiring, while the reduced slew rate controls high-frequency emissions generated by the driver. The 8-pin SOIC package supports compact interface sections on mixed-signal boards. Designers should pay attention to the selected ADM4854 ordering option’s duplex and enable behavior, and should implement bus protection before long cables leave the enclosure.

What is the ADM4854AR?
The ADM4854AR is a 5 V differential line transceiver for RS-485 and RS-422 buses, supporting half-duplex and full-duplex communication at rates up to 115 kbps. Analog Devices identifies the device as an ADM4854-family member and describes it as a slew-rate-limited transceiver with true fail-safe receiver inputs. It is packaged in an 8-pin SOIC for industrial, instrumentation, building-control, and multipoint data-bus equipment.
What is the maximum data rate of ADM4854AR?
The ADM4854AR supports a maximum data rate of 115 kbps. This rate is one of the functional divisions in the ADM4850 through ADM4857 family, whose options range from 115 kbps to 10 Mbps. The reduced slew rate associated with the 115 kbps ADM4854 option helps limit electromagnetic interference, making it suitable for conventional low-speed RS-485 links.
Where can I download the ADM4854AR datasheet PDF?
The official ADM4854 product page at Analog Devices is the appropriate starting point for the ADM4854AR datasheet and technical documentation. It describes the shared features and ordering options of the ADM4850 through ADM4857 differential transceiver family. The manufacturer page should be used for the authoritative pin description, electrical limits, and package details before assigning PCB signals.
Where can I find the ADM4854AR pinout?
Use the pin-description table in the Analog Devices ADM4854 manufacturer documentation to identify the exact pins for the ADM4854AR ordering option. The device is housed in an 8-pin SOIC, designated PDSO8, but the R suffix ordering information should be checked for the applicable lead and package configuration. The pin diagram is not reproduced here because its signal labels are not stated in the available source material.
Is the ADM4854AR suitable for industrial RS-485 networks?
Yes, the ADM4854AR is suitable for industrial RS-485 networks operating at up to 115 kbps. Its 5 V supply, differential signaling, reduced slew rate, and true fail-safe receiver inputs align with conventional instrumentation and control networks. Actual range also depends on cable type, topology, grounding, termination, transceiver loading, and the electromagnetic environment of the installation.
Why does the ADM4854 use a reduced slew rate?
The ADM4854 uses a reduced slew rate to lower electromagnetic interference while preserving its 115 kbps communication rate. Slower signal edges generally produce less high-frequency energy, which can reduce radiated emissions and susceptibility to cable coupling. This characteristic is particularly useful in industrial environments where long cables and adjacent sensitive circuitry may increase EMI concerns.
Can the ADM4854AR operate in both half-duplex and full-duplex systems?
Yes, the ADM4854 family supports half-duplex and full-duplex configurations. The exact operating mode depends on the ADM4854 ordering option and how its driver-enable and receiver-enable functions are connected. Use the Analog Devices pin-description and ordering tables to confirm whether the selected ADM4854AR configuration is intended for shared-bus half-duplex operation or separate full-duplex channels.
What is true fail-safe behavior in the ADM4854AR receiver?
True fail-safe behavior means the receiver is designed to provide a defined output state when the differential input is idle or undriven. Analog Devices lists true fail-safe receiver inputs as a feature of the ADM4850 through ADM4857 family. This helps a receiving node interpret an absent or disabled driver predictably instead of allowing bus noise to determine the logic state.
What is the best drop-in replacement for ADM4854AR?
The closest documented drop-in candidate is the ADM4854ARZ because it is listed in an 8-SOIC package and belongs to the same ADM4854 function family. Confirm pin assignments, supply limits, receiver enable behavior, and the exact ordering suffix against the Analog Devices documentation before substitution. Other ADM4854 variants that differ in duplex, enable, or packing configuration should not be assumed interchangeable without that check.
Can ADM4854ARZ replace ADM4854AR?
ADM4854ARZ is a potential drop-in replacement because it is identified as an 8-SOIC ADM4854-family device, matching the ADM4854AR package format. Final qualification requires comparing the exact pinout, electrical limits, and ordering-option behavior in the manufacturer documentation. The available cross-reference material supports the package-family relationship but does not establish every ordering suffix as interchangeable.
What can replace ADM4854AR?
ADM4854ARZ is the most direct supported candidate because it is listed as an 8-SOIC member of the ADM4854 transceiver family. A valid replacement must preserve the 5 V interface, 115 kbps class, RS-485/RS-422 electrical behavior, receiver fail-safe function, and pin configuration. Treat reel-code variants as packaging options rather than distinct engineering alternatives.
When should I choose ADM4854AR instead of a faster RS-485 transceiver?
Choose the ADM4854AR when the bus needs up to 115 kbps and low EMI is a priority. Its reduced slew rate is better aligned with long industrial cables, legacy equipment, and installations where radiated or reflected interference must be controlled. Choose a faster ADM485-family option only when the application requires higher throughput and its edge-rate, EMI, and system-level behavior have been validated.
Is ADM4854AR the same as ADM4854AR-REEL7?
ADM4854AR-REEL7 represents a tape-and-reel ordering or packaging designation rather than a distinct electrical transceiver family. Its core ADM4854 function remains associated with the 5 V, 115 kbps RS-485/RS-422 device. When comparing suffixes, confirm whether the difference is only mechanical handling or also affects grade, temperature range, lead style, qualification, or orderable configuration.
Where can I buy ADM4854AR online?
Use the Request a Quote form on this page to request current ADM4854AR commercial availability, lead time, and minimum-order information. Quote-based sourcing is appropriate because availability and commercial terms can change by package suffix, production status, and order quantity. Provide the complete ADM4854AR ordering code and required quantities so the request can be matched to the correct configuration.
What is the price of ADM4854AR?
Current ADM4854AR pricing depends on the exact ordering suffix, package format, order quantity, and supply status. Use the Request a Quote form on this page for a current quotation rather than relying on a static figure that may become outdated. Include the required quantity, target package or reel format, and intended production schedule with the request.
What is the lead time for ADM4854AR?
The current ADM4854AR lead time depends on the exact orderable configuration and factory availability. Use the Request a Quote form on this page to request a lead-time commitment and minimum-order quantity. Providing the full MPN, annual usage, and required delivery date enables the sourcing request to be evaluated against the appropriate production configuration.
Is ADM4854AR in stock?
Stock status for ADM4854AR can vary by package suffix, manufacturing allocation, and order quantity. Use the Request a Quote form on this page to check current availability for the exact ADM4854AR configuration you need. Include your required quantity and delivery schedule so the quotation can reflect the relevant supply position.
What are the key specifications of ADM4854AR that engineers should know?
The ADM4854AR is a 5 V RS-485/RS-422 differential transceiver rated for operation up to 115 kbps, with half-duplex and full-duplex family options, reduced slew rate for low EMI, and true fail-safe receiver inputs. It uses an 8-pin SOIC package. The Analog Devices product page identifies these family-level characteristics, while the ordering and pin tables define the exact selected device configuration.

بيانات مرجعية هندسية لـ ADM4854AR — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose ADM4854AR for RS-485 or RS-422 equipment that communicates at no more than 115 kbps and benefits from reduced signal-edge rates for lower EMI. It is a practical choice for industrial instrumentation, building controls, remote sensors, and supervisory factory systems. ADM4854ARZ is the closest documented drop-in candidate because it is listed as an 8-SOIC ADM4854-family device; confirm its exact suffix-specific pinout, qualification, and ordering status before releasing a substitution. For a newer design, compare the ADM4854 family against faster options only when throughput requires them, since faster transceivers generally use steeper edges and require greater attention to cable topology and EMI. Reel-code variants should be treated as packaging options, not different electrical substitutes.

المقارنة مع البدائل

المعامل هذا المنتج ADM4854ARZ
Brand Analog Devices Analog Devices
Package 8-SOIC 8-SOIC
Product Type RS-485/RS-422 differential line transceiver RS-485/RS-422 differential line transceiver
Supply Voltage 5 V 5 V
Maximum Data Rate 115 kbps 115 kbps
Duplex Support Half-duplex and full-duplex family options Half-duplex and full-duplex family options
EMI Characteristic Reduced slew rate for low EMI Reduced slew rate for low EMI
Fail-Safe Receiver True fail-safe receiver inputs True fail-safe receiver inputs
Maximum Supply Current 5 uA 5 uA

أبرز الفروقات

  • Low-EMI data-rate option (مقابلADM4854ARZ)
  • Direct package-family fit (مقابلADM4854ARZ)
  • Multipoint differential interface (مقابلADM4854ARZ)

ملاحظات التصميم

Route the RS-485 driver, receiver, and connector as a differential pair with closely matched geometry and a continuous reference plane. Keep the transceiver and protection components close to the cable entry, minimize stub branches, and avoid routing the differential pair beneath switching nodes or digital clocks. A compact connection between the transceiver and protection network also limits parasitic inductance that can otherwise degrade surge response.

Use the reduced slew rate as part of the EMC strategy, but do not treat it as a substitute for controlled bus layout. Keep long RS-485 cables away from high-current edges and high-frequency nodes, use twisted-pair cable with consistent impedance, and place termination only where required by the bus topology. Confirm the final emissions and immunity behavior in the assembled enclosure because connector cables and auxiliary circuitry can dominate system EMI.

Do not substitute different ADM4854 ordering options solely because their data rates are close. Half-duplex versus full-duplex configuration, driver-enable behavior, receiver-enable polarity, package lead style, and qualification markings can change the pin implementation. Compare the exact ordering table and pin description, then verify supply current, common-mode range, temperature limits, and protection requirements before approving a substitution.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance status was not explicitly identified in the cited product material. Confirm current environmental, material, and automotive qualification requirements with Analog Devices before production release.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ADM4854AR datasheet ADM4854AR pinout ADM4854AR datasheet pdf ADM4854AR equivalent ADM4854AR replacement ADM4854AR cross reference ADM4854AR vs ADM4854ARZ ADM4854AR SOIC-8 pinout ADM4854AR 115kbps RS-485 transceiver Analog Devices ADM4854AR ADM4854AR industrial RS-485 ADM4854AR price ADM4854AR stock where to buy ADM4854AR

المكونات والمصطلحات ذات الصلة

Analog Devices ADM4854AR ADM4854ARZ ADM4854 ADM4850 ADM4851 ADM4852 ADM4853 ADM4855 ADM4856 ADM4857 RS-485 RS-422 differential line transceiver interface IC half-duplex communication full-duplex communication multipoint bus reduced slew rate true fail-safe receiver electromagnetic interference 8-pin SOIC PDSO8 surface mount industrial automation
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر