Analog Devices

ADM488ABRMZ - 250kbps Full-Duplex RS-485 | Analog Devices

MPN: ADM488ABRMZ ✓ نشط
5 V Vdss EIA RS-422 and EIA RS-485 Rds(on) 8-pin MSOP Package
الحد الأدنى للطلب: 1 |

ADM488ABRMZ نظرة عامة

The Analog Devices ADM488ABRMZ is a 5 V, low-power, slew-rate-limited full-duplex RS-485 and RS-422 transceiver operating at 250 kbps, packaged in an 8-pin MSOP. It provides one transmitter and one receiver for balanced differential data links, combining low power consumption with controlled transition rates that help limit unwanted EMI on multipoint bus networks.

An RS-485 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals for reliable communication over longer, noise-prone cables. The ADM488A belongs to the transceiver family within the broader interface IC and data-communication hierarchy. Its full-duplex operation supports simultaneous transmitting and receiving, making it appropriate for point-to-point links and systems where a dedicated receive path must remain active during transmission.

Key characteristics include a 5 V supply, a maximum data rate of 250 kbps, RS-485 and RS-422 compatibility, and slew-rate-limited operation. The controlled edge rate is important in distributed bus systems because it reduces reflected signaling and high-frequency EMI compared with an unrestricted high-speed driver. The manufacturer identifies the ADM488 as a production device suitable for balanced multipoint bus transmission lines.

The device architecture supports separate transmit and receive signal paths. Digital data enters through the driver-control and data inputs, while the receiver produces a logic output for the host controller. Slew-rate limiting shapes the output transitions, and the balanced differential bus interface improves common-mode noise rejection. Exact input thresholds, output levels, supply-current limits, temperature limits, and protection characteristics should be confirmed from the manufacturer data sheet during design-in.

Typical uses include industrial equipment links, building automation, process-control networks, instrumentation, and factory communication systems that operate at moderate data rates. Full duplex is particularly useful for dedicated links where two nodes need simultaneous bidirectional communication rather than time-shared half-duplex operation. It can also support longer cable runs when the system follows the grounding, termination, and transceiver-count recommendations for RS-485.

A key design consideration is that reliable RS-485 performance depends on the complete network, not only the IC. Use a proper bus topology, place termination at the physical ends, maintain a common reference within the cable’s common-mode range, and decouple the 5 V supply close to the device. The slow, controlled data rate also requires confirmation that the selected cable, connectors, and protocol timing can support 250 kbps.

This page organizes the manufacturer specifications, package information, sourcing details, verified alternatives, application guidance, and design cautions for engineers evaluating the ADM488ABRMZ. It also separates confirmed device characteristics from parameters that require selection against the latest manufacturer documentation.

بدائل مباشرة لـ ADM488ABRMZ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ADM488ABRMZ (نفس عامل الشكل والبصمة) — يختلف في Mounting Type, Package, Product Type.

Analog Devices
Mounting Type: Through-hole PDIP
Package: 8-PDIP (0.300 inch, 7.62 mm pitch)
Product Type: Full-duplex differential transceiver
قارن مع ADM488ABRMZ →

ADM488ANZ

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
Analog Devices
📦 8-pin MSOP
Full-duplex differential transceiver · EIA RS-422 and EIA RS-485 · 1 driver · 1 receiver · 250 kbps · 4.5 V to 5.5 V · Full duplex · Slew-rate limited

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ADM488ABRMZ-REEL7

✅ بديل مباشر
📦 8-pin MSOP
Same 5 V, 250 kbps full-duplex RS-485/RS-485 function and 8-MSOP footprint; reel packaging replaces the tube presentation.

📋 بديل مرجعي (غير موجود في الكتالوج)

ADM488ABRMZ المواصفات

Product Type RS-422/RS-485 differential line transceiver
Transceiver Configuration 1 transmitter / 1 receiver
Duplex Mode Full duplex
جهد التغذية 5 V
Maximum Data Rate 250 kbps
Supported Standards EIA RS-422 and EIA RS-485
Driver Architecture Slew-rate limited
Power Class Low power
العلبة 8-pin MSOP
Package Width 3.00 mm
Package Length 0.118 in
نوع التركيب Surface mount
Packaging Tube
حالة RoHS ROHS3 compliant
Production Status Production

دليل تكوين أطراف ADM488ABRMZ 0.118 in

تكوين الأطراف لـ ADM488ABRMZ (حزمة 0.118 in). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 0.118 in لـ ADM488ABRMZ

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM488ABRMZ.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ADM488ABRMZ مناسب لـ 6 التطبيقs: Industrial Equipment Communication, Process-Control Instrumentation, Building Automation Networks, Instrumentation and Test Systems, Factory Automation Controllers, Medical and Monitoring Equipment.

🏭

Industrial Equipment Communication

The ADM488ABRMZ fits dedicated full-duplex links between industrial controllers, sensors, and remote equipment operating at up to 250 kbps. Its 5 V transceiver combines balanced differential signaling with slew-rate-limited transitions, helping control high-frequency EMI on factory cabling. Place the device at the bus interface, connect the controller logic to its digital inputs and outputs, and design the board for a common reference within the transceiver's operating limits. The 250 kbps ceiling must be reconciled with the selected protocol, cable length, and environmental noise conditions.

🖥️

Process-Control Instrumentation

The ADM488ABRMZ can provide a dedicated full-duplex communications path between a process controller and remote instrumentation. The balanced bus architecture supports RS-485 and RS-422 signaling, while the 250 kbps rate is appropriate for many supervisory and configuration channels rather than high-speed sensor streaming. Its low-power, slew-rate-limited operation is useful in distributed cabinets where reducing edge-rate-related EMI is important. The implementation must provide a clean 5 V rail, suitable grounding, and a termination strategy matched to the physical bus topology.

🧩

Building Automation Networks

The ADM488ABRMZ is appropriate for building-automation nodes that exchange commands and status through a dedicated balanced link at moderate speed. Its 250 kbps maximum rate supports common supervisory protocols, while full duplex allows a controller to receive updates while transmitting commands. The controlled slew rate is beneficial in buildings where cables run near lighting, motors, and other potential EMI sources. Designers should observe the bus topology, common-mode requirements, decoupling, and protection requirements of the installation rather than treating the transceiver as a complete surge-protection solution.

🔧

Instrumentation and Test Systems

The ADM488ABRMZ can link laboratory or field-test equipment to a remote instrument over a dedicated full-duplex RS-485 or RS-422 channel. The interface rate of 250 kbps is suitable for measurement configuration, status, and moderate data transfers where lower EMI and reliable common-mode rejection are priorities. Its 8-pin MSOP footprint supports compact multi-channel measurement hardware. Use short, controlled differential traces where possible, confirm the receiver’s input arrangement from the data sheet, and validate the complete cable and grounding system at the intended operating rate.

🏭

Factory Automation Controllers

The ADM488ABRMZ is useful in factory automation controllers that require a dedicated point-to-point or multipoint-compatible differential communication port. The 250 kbps rate covers command traffic, diagnostics, and machine status exchange, while the low-power 5 V design fits embedded control hardware. Full-duplex operation can reduce turnaround delays compared with time-shared half-duplex links. Firmware must still implement bus arbitration, turnaround, fault recovery, and timing requirements appropriate to the selected communication standard, and the board should include local decoupling and appropriately placed protection.

💊

Medical and Monitoring Equipment

The ADM488ABRMZ can serve as the communications interface in monitoring and diagnostic equipment that uses a dedicated balanced link at 250 kbps or less. Its low-power operation and controlled differential transitions suit compact multi-function instruments where connector space and EMI control matter. Because ordinary RS-485 transceivers do not by themselves provide medical isolation, patient-contact protection, or regulatory certification, the complete design must add the required isolation, protection, creepage, and safety measures. Verify the exact electrical limits and application suitability against the current manufacturer documentation.

What is the ADM488ABRMZ?
The ADM488ABRMZ is a 5 V, 250 kbps, full-duplex RS-485 and RS-422 transceiver from Analog Devices. It combines one balanced transmitter and one receiver in an 8-pin MSOP package. According to the Analog Devices ADM488 product page, the device is intended for balanced differential communication on multipoint bus transmission lines, with slew-rate-limited operation for controlled signal transitions.
What is the maximum data rate of ADM488ABRMZ?
The ADM488ABRMZ supports a maximum data rate of 250 kbps. This figure is confirmed by the Analog Devices product page and distributor product descriptions. The rated rate is suitable for moderate-speed industrial and instrumentation links, but the complete system must also satisfy the timing requirements of the selected protocol, cable, connectors, and termination network.
Is ADM488ABRMZ full duplex or half duplex?
The ADM488ABRMZ is a full-duplex transceiver with one transmitter and one receiver. Full duplex allows a dedicated link to transmit and receive simultaneously rather than sharing a single bus direction. Analog Devices describes the ADM488 as a differential transceiver for balanced communication on multipoint transmission lines, while the listed 8-MSOP package supports a compact implementation.
Where can I download the ADM488ABRMZ datasheet PDF?
The official ADM488ABRMZ documentation is available through the Analog Devices ADM488 product page at https://www.analog.com/en/products/adm488.html. The page links to the current data sheet, product selection information, and evaluation resources. Use the manufacturer copy for final pin assignments, electrical limits, timing, and application guidance before committing the circuit to production.
Where can I find the ADM488ABRMZ pinout?
The ADM488ABRMZ pinout is published in the Analog Devices ADM488 data sheet linked from the official product page. The device is an 8-pin MSOP and includes transmit-enable, receive-enable, data-input, receive-output, power, ground, and balanced bus connections. Assign the PCB tracks from the manufacturer pin-description table because exposed-pad and package-option details must match the ordered device.
What standards does ADM488ABRMZ support?
The ADM488ABRMZ supports EIA RS-422 and EIA RS-485 differential communications through its transmitter and receiver stages. Analog Devices identifies the part as a low-power, slew-rate-limited transceiver for balanced multipoint transmission lines. Confirm the applicable standard requirements for your system, including cable length, node count, grounding, and common-mode limits.
What are the advantages of slew-rate-limited RS-485 transceivers?
Slew-rate limiting controls the transition rate of the transmitted differential signal and can reduce high-frequency EMI and reflected signaling on installed cabling. In the ADM488ABRMZ, the maximum signaling rate is 250 kbps, so the controlled edge rate is consistent with a moderate-speed bus. Proper topology, termination, and common-mode design remain necessary for reliable operation.
What can replace the ADM488ABRMZ?
The closest documented same-footprint options are the ADM488ANZ and ADM488ABRMZ-REEL7 families, but replacement must be checked against ordering code, temperature grade, and packaging. The verified cross-reference results did not identify a qualified cross-brand pin-to-pin equivalent with published specifications. Treat any third-party substitute as a functional candidate until its pinout, logic levels, supply current, slew behavior, and protection ratings are verified.
Can ADM488ABRMZ-REEL7 replace ADM488ABRMZ?
The ADM488ABRMZ-REEL7 retains the ADM488ABRMZ electrical configuration and 8-pin MSOP package, with the principal documented difference being reel rather than tube presentation. The manufacturer-family ordering data identifies both as 250 kbps full-duplex RS-485 transceivers. For an existing PCB, confirm the pin compatibility, tape orientation, reel dimensions, and applicable temperature and marking details before substitution.
Is ADM488ABRMZ suitable for industrial communication networks?
The ADM488ABRMZ is suitable for moderate-speed industrial communication links because it provides a 250 kbps RS-485/RS-422 interface with slew-rate-limited, balanced differential signaling. Its low-power design is also appropriate for distributed equipment. Industrial suitability still depends on the complete installation, including surge protection, grounding, isolation requirements, environmental exposure, and whether the node count and cable length are permitted.
Where to buy ADM488ABRMZ online?
Use the Request a Quote form on this XAIPART product page to request ADM488ABRMZ availability, current commercial terms, and the correct tube packaging configuration. The part is identified as an active Analog Devices transceiver in an 8-pin MSOP, and distributor records show the tube-packaged ordering code. XAIPART can confirm supply status and lead time through the quote workflow.
What is the price of ADM488ABRMZ?
Use the Request a Quote form on this page for the current ADM488ABRMZ commercial quote. The structured pricing view reflects currently printable quantity-break evidence, while this page is quote-first for this exact ordering code. Request the quantity, tube packaging requirement, target date, and shipping destination so the response can reflect the complete procurement requirement.
What is the lead time and stock status for ADM488ABRMZ?
The current stock position and lead time for ADM488ABRMZ should be confirmed through the Request a Quote form on this page. A distributor record lists the tube-packaged MPN with a 10-week lead time and a minimum order quantity of 1, but that record may not reflect current factory or channel availability. Submit the required quantity and schedule for an updated commitment.
ADM488ABRMZ vs ADM489A - which is better for my bus?
Choose ADM488ABRMZ when a 250 kbps full-duplex RS-485/RS-422 interface and 8-pin MSOP implementation are required. The related ADM489A family also addresses low-power differential line communication, but its exact speed and pin configuration differ, so it is not automatically a drop-in replacement. Compare the relevant manufacturer data sheet for data rate, receiver topology, shutdown behavior, and bus-pin arrangement.
What are the key specifications of ADM488ABRMZ that engineers should know?
The key ADM488ABRMZ specifications are a 5 V supply, 250 kbps maximum data rate, full-duplex operation, one transmitter and one receiver, slew-rate-limited signaling, and an 8-pin MSOP package. Analog Devices identifies RS-422 and RS-485 balanced communication as the intended applications. Production status, low-power operation, and the tube package designation are also identified in the product and distributor records.
What is the best cross-brand equivalent for ADM488ABRMZ?
No cross-brand equivalent is presented as a verified drop-in replacement for the ADM488ABRMZ in the available cross-reference results. Selecting a competing RS-485 transceiver requires confirmation of the same 8-pin MSOP footprint, driver and receiver logic levels, enable polarity, bus pinout, 250 kbps or better timing, supply current, common-mode range, and protection behavior. Avoid replacing the part solely on headline data rate and package height.

بيانات مرجعية هندسية لـ ADM488ABRMZ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ADM488ABRMZ when a compact, low-power, full-duplex RS-485 or RS-422 link is required and the production design specifies the tube-packaged ordering code. Its 250 kbps rate, slew-rate-limited driver, and 8-pin MSOP package suit industrial, instrumentation, building-automation, and test-system links that value controlled differential signaling more than maximum bus speed. Select ADM488ABRMZ-REEL7 when the assembly process uses tape-and-reel presentation and the reel orientation is compatible with the PCB. Consider ADM488ANZ only after confirming its exact ordering suffix, temperature grade, pin arrangement, and marking against the current manufacturer documentation. None of the listed alternatives should be selected solely because it is also labeled RS-485; verify enable polarity, receiver configuration, bus-pin arrangement, electrical limits, protection, and lifecycle before substitution.

المقارنة مع البدائل

المعامل هذا المنتج ADM488ANZ ADM488ABRMZ-REEL7
Brand Analog Devices Analog Devices Analog Devices
Package 8-pin MSOP 8-pin MSOP 8-pin MSOP
Transceiver Configuration 1 transmitter / 1 receiver 1 transmitter / 1 receiver 1 transmitter / 1 receiver
Supply Voltage 5 V 5 V 5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps
Duplex Mode Full duplex Full duplex Full duplex
Supported Interfaces RS-422 / RS-485 RS-422 / RS-485 RS-422 / RS-485
Driver Architecture Slew-rate limited Slew-rate limited Slew-rate limited
Power Class Low power Low power Low power

أبرز الفروقات

  • Full-duplex communication in a compact 8-pin MSOP (مقابلADM488ANZ)
  • Identical documented data rate and bus architecture across reel ordering (مقابلADM488ABRMZ-REEL7)
  • Production-status positioning for new RS-485 designs (مقابلADM488ANZ)

ملاحظات التصميم

Route the differential bus pair as a short, tightly coupled pair and keep it away from switching nodes, clock edges, and high-current return paths. Place any termination components at the physical ends of the bus rather than at every node. The controlled 250 kbps signaling rate reduces edge-rate stress, but signal integrity still depends on topology, trace geometry, connector return paths, and the grounding reference.

Place the 5 V bypass capacitor immediately adjacent to the device power and ground pins, with a short ground return to the package. Keep sensitive receive and logic traces away from the driver output and bus routing. Verify supply tolerance, input thresholds, and current limits against the manufacturer data sheet because those operating details were not included in the product-page records used for this listing.

Do not assume that a package-height match and a 250 kbps headline rating guarantee interchangeability. Before substituting another transceiver, compare every pin, enable polarity, receiver input arrangement, bus-output behavior, common-mode range, fail-safe state, supply current, and protection rating. For the ADM488ABRMZ and ADM488ABRMZ-REEL7, also verify the tube-versus-reel orientation and automated pick-and-place requirements.

The slew-rate-limited driver is valuable in industrial environments because it reduces very fast edge components and associated radiated emissions. However, EMI performance still depends on cable shielding, connector construction, common-mode grounding, board-layer stackup, and enclosure design. Use the lowest data rate that satisfies the protocol and validate emissions and immunity at the finished-system level rather than relying on the transceiver rate alone.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The distributor product record identifies the ADM488ABRMZ as ROHS3 compliant. The Analog Devices product page identifies the ADM488 family as being in production. No additional REACH, halogen-free, conflict-minerals, or automotive-qualification claims were established.

تم التحقق من البيانات في: 2026-11-19 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ADM488ABRMZ datasheet ADM488ABRMZ datasheet pdf ADM488ABRMZ pinout ADM488ABRMZ specifications ADM488ABRMZ equivalent ADM488ABRMZ replacement ADM488ABRMZ price ADM488ABRMZ stock Analog Devices ADM488ABRMZ ADM488ABRMZ 8-MSOP footprint ADM488ABRMZ full duplex RS-485 ADM488ABRMZ industrial communication ADM488ABRMZ vs ADM488ANZ ADM488ABRMZ vs ADM488ABRMZ-REEL7

المكونات والمصطلحات ذات الصلة

Analog Devices ADM488ABRMZ ADM488ANZ ADM488ABRMZ-REEL7 ADM488A ADM489A RS-485 transceiver RS-422 transceiver full-duplex transceiver differential line transceiver interface IC data communications multipoint bus slew-rate limiting balanced differential signaling 250 kbps 5 V supply low-power design 8-pin MSOP MSOP package family surface-mount package industrial automation building automation process instrumentation EMI control
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر