Texas Instruments

DS90LV032ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments

MPN: DS90LV032ATMTC ✗ انتهى عمره الإنتاجي
3 V Vdss 16-pin TSSOP Package >200 MHz Speed
الحد الأدنى للطلب: 1 |

DS90LV032ATMTC نظرة عامة

The Texas Instruments DS90LV032ATMTC is a four-channel, 3-V LVDS differential line receiver that converts four low-voltage differential inputs into 3-V CMOS outputs. It supports data rates in excess of 400 Mbps, equivalent to a 200 MHz data clock, and accepts a typical differential input signal of 350 mV. The device is packaged in a 16-pin TSSOP for high-speed point-to-point digital-interface applications.

An LVDS receiver is an interface circuit that detects the voltage difference between a complementary pair of low-voltage differential signals. The DS90LV032A family belongs to the hierarchy of differential line receivers, digital interface ICs, and semiconductors. Compared with older PECL or ECL interfaces, LVDS provides a lower-voltage differential transport method with low power dissipation while supporting high-speed data transfer over balanced connections.

The receiver architecture supports four independent LVDS channels, low-power operation, and 3-V CMOS-compatible outputs. Its differential input threshold is centered around a typical 350 mV signal, while its operating speed exceeds 400 Mbps. These characteristics make the device useful when a system must recover digital data from balanced cables, backplanes, or point-to-point links without converting the physical layer to single-ended logic internally.

The DS90LV032A is designed to work with the DS90LV031A companion line driver as an alternative to higher-power PECL or ECL interface solutions. Its quad-channel organization reduces the number of interface devices needed when several differential links are required. Because LVDS is differential, the implementation must preserve controlled impedance, symmetrical routing, and proper termination to avoid common-mode noise and timing degradation.

Typical applications include industrial control links, high-speed backplanes, video and data acquisition systems, instrumentation, test and measurement equipment, and point-to-point transfers between circuit boards. The receiver is most appropriate where several high-speed links must operate from a 3-V supply while maintaining a compact 16-pin footprint.

PCB layout is critical in a 400-Mbps design. Place the receiver close to the connector or transmission-line endpoint, provide a continuous reference plane, match differential pair geometry, and avoid stubs. Verify signal and ground return paths carefully because small impedance discontinuities can create reflections that degrade receiver performance even when the logic itself operates correctly.

This page combines the manufacturer's device description with package information, source links, replacement analysis, and practical interface-layout guidance. It is designed to help engineers determine whether the DS90LV032ATMTC fits an existing 16-pin TSSOP LVDS design and how to integrate it into a high-speed, low-power differential interface.

بدائل مباشرة لـ DS90LV032ATMTC — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع DS90LV032ATMTC (نفس عامل الشكل والبصمة) — يختلف في Lifecycle Status, Maximum Data Rate, Package, Supply Voltage.

Texas Instruments
Lifecycle Status: Active
Maximum Data Rate: Greater than 400 Mbps
Package: 16-pin narrow SOIC (D)
قارن مع DS90LV032ATMTC →

DS90LV032ATMTC/NOPB

✅ بديل مباشر
📦 16-pin TSSOP
Lead-free /NOPB orderable configuration; receiver function, 400 Mbps data rate, 3-V supply, and 16-pin TSSOP interface remain equivalent

📋 بديل مرجعي (غير موجود في الكتالوج)

DS90LV032ATMTCX/NOPB

✅ بديل مباشر
📦 16-pin TSSOP
Lead-free /NOPB configuration with an additional ordering suffix; receiver function, 400 Mbps data rate, and 16-pin TSSOP package remain equivalent

📋 بديل مرجعي (غير موجود في الكتالوج)

DS90LV032ATM

✅ بديل مباشر
Texas Instruments
📦 16-pin TSSOP
LVDS quad differential line receiver · 4 channels · 0 drivers · 3 V to 3.6 V · 3 V · Greater than 400 Mbps · 200 MHz · 350 mV typical

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DS90LV032ATMTC المواصفات

Receiver Configuration 0/4 differential receiver
Number of Channels 4 channels
Input Signal Type LVDS differential input
Output Signal Type 3-V CMOS output
Maximum Data Rate >400 Mbps
Equivalent Data Clock >200 MHz
جهد التغذية 3 V
Typical Differential Input Signal 350 mV
Power Dissipation Ultra-low power dissipation
العلبة 16-pin TSSOP
نوع التركيب Surface mount
حالة دورة الحياة Not Recommended for New Designs
Lead-Free Code Yes
RoHS Code No
Application High-speed point-to-point LVDS interfaces
Companion Driver DS90LV031A

تكوين أطراف DS90LV032ATMTC

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
دبوس 1 1OUT — Channel 1 CMOS output
دبوس 2 1IN+ — Channel 1 non-inverting differential input
دبوس 3 1IN- — Channel 1 inverting differential input
دبوس 4 2OUT — Channel 2 CMOS output
دبوس 5 2IN+ — Channel 2 non-inverting differential input
دبوس 6 2IN- — Channel 2 inverting differential input
دبوس 7 GND — Ground
دبوس 8 3OUT — Channel 3 CMOS output
دبوس 9 3IN+ — Channel 3 non-inverting differential input
دبوس 10 3IN- — Channel 3 inverting differential input
دبوس 11 4OUT — Channel 4 CMOS output
دبوس 12 4IN+ — Channel 4 non-inverting differential input
دبوس 13 4IN- — Channel 4 inverting differential input
دبوس 14 GND — Ground
دبوس 15 VCC — 3-V power supply
دبوس 16 VCC — 3-V power supply

التطبيقات النموذجية

DS90LV032ATMTC مناسب لـ 6 التطبيقs: Industrial Control Backplanes, High-Speed Data Acquisition, Video and Imaging Links, Point-to-Point Board Interconnects, Test and Measurement Systems, Networking and Communication Modules.

🏭

Industrial Control Backplanes

The DS90LV032ATMTC fits industrial backplanes that carry several balanced control or measurement links over distances where single-ended signaling would be more noise-sensitive. Its four differential receivers support data rates in excess of 400 Mbps, while the 3-V CMOS outputs can feed counters, comparators, latch logic, or downstream controller inputs. The main design benefit is four channels in one 16-pin TSSOP, reducing receiver count and standardizing the interface footprint. For reliable industrial operation, maintain controlled differential impedance, provide a continuous reference plane, avoid stubs, and route each LVDS pair away from switching-power nodes. The receiver does not create the transmitted signal, so the system also needs a compatible LVDS line driver such as the DS90LV031A or another source meeting the same voltage and timing requirements.

📊

High-Speed Data Acquisition

The DS90LV032ATMTC is appropriate for data-acquisition and instrumentation systems that receive several high-speed differential signals from a remote board, sensor interface, or test fixture. Its receiver architecture detects a typical 350 mV differential input and produces 3-V CMOS outputs at data rates above 400 Mbps. This allows measurement or processing logic to operate with conventional single-ended digital levels while the board-to-board connection remains balanced and noise resistant. Use matched differential routing and the termination strategy specified by the manufacturer datasheet. Keep the receiver close to the connector or cable termination to minimize round-trip signal degradation, and verify source-to-destination timing across all four channels. The receiver adds no protocol conversion, so framing, synchronization, and data-valid interpretation remain the responsibility of the surrounding system.

📺

Video and Imaging Links

The DS90LV032ATMTC can terminate balanced links carrying digitized video or imaging data when the system operates from a 3-V supply. Support for rates in excess of 400 Mbps provides sufficient margin for parallelized pixel data delivered over multiple LVDS pairs, while the four-channel receiver consolidates related signals into a single 16-pin TSSOP. Each differential pair should be routed with matched geometry and a continuous ground reference to preserve common-mode behavior and minimize data-dependent jitter. Place decoupling close to the receiver supply pins and confirm that the driver, cable, connectors, and receiver form a complete channel with an appropriate termination arrangement. Because this device outputs CMOS logic rather than regenerated LVDS, downstream logic must provide any required blanking, synchronization, or frame-level control.

🖥️

Point-to-Point Board Interconnects

The DS90LV032ATMTC is well suited to board-to-board point-to-point links where four independent data channels must cross a connector or controlled trace environment. Its 400-Mbps-plus capability supports modern parallel data transfer without requiring a high-voltage PECL or ECL interface, and the 3-V CMOS outputs simplify connection to ordinary logic. Using four receivers in one 16-pin TSSOP can reduce board area and simplify power distribution compared with four separate one-channel devices. The design should preserve differential symmetry through connector breakout regions, which frequently require deliberate routing adjustments. Place the receiver near the connector, maintain a continuous return plane, and test the completed channel for reflections, overshoot, and common-mode limits. The DS90LV032A is a receiver only, so the transmitting board needs a compatible LVDS driver such as the DS90LV031A.

🧰

Test and Measurement Systems

The DS90LV032ATMTC can serve as the receiving element in test and measurement equipment that transfers synchronized commands or results between modules. Its four channels support rates above 400 Mbps while maintaining low power dissipation, making it useful when multiple high-speed links share a compact 3-V architecture. The receiver converts balanced LVDS into 3-V CMOS levels that can be sampled by counters, control processors, or FPGA interface logic. Designers should account for source and destination clocking, deterministic latency, and channel-to-channel skew in the complete system. Short receiver traces, proper supply decoupling, controlled impedance, and careful treatment of connector return pins are essential. The part does not include framing or clock recovery, so protocol and synchronization functions must be implemented externally.

🌐

Networking and Communication Modules

The DS90LV032ATMTC may be used in communication modules that receive several high-speed differential data streams from a chassis, mezzanine card, or remote line-card interface. Its 400-Mbps-plus operation and 3-V CMOS output make it suitable for intermediate link layers that require low-power termination rather than legacy PECL or ECL levels. Four receive channels in one 16-pin TSSOP allow a compact interface section, but routing must remain short and deterministic to preserve timing margin. Use the manufacturer reference circuit and pin descriptions to establish supply decoupling and termination, and ensure the transmitting side satisfies the receiver's differential-input requirements. Because the device provides physical-layer reception only, packet framing, error handling, flow control, and higher-layer synchronization remain external to the IC.

ملخص المنتجات الموصى بها

DS90LV031A Companion quad LVDS line driver يُستخدم في: Industrial Control Backplanes, High-Speed Data Acquisition, Video and Imaging Links, Point-to-Point Board Interconnects, Test and Measurement Systems, Networking and Communication Modules
What is the DS90LV032ATMTC?
The DS90LV032ATMTC is a four-channel, 3-V LVDS differential line receiver from Texas Instruments that converts differential inputs into 3-V CMOS outputs. According to the manufacturer datasheet, it supports data rates in excess of 400 Mbps, or 200 MHz, and is intended for high-speed point-to-point interfaces. The device uses low power dissipation and accepts a typical differential input signal of 350 mV.
What is the data rate of DS90LV032ATMTC?
The DS90LV032ATMTC supports data rates in excess of 400 Mbps, corresponding to a data-clock frequency above 200 MHz. Texas Instruments describes the DS90LV032A as a quad CMOS differential receiver for applications requiring both high data rates and low power dissipation. This performance makes it suitable for balanced cable, backplane, and board-to-board communication links.
What package does DS90LV032ATMTC use?
The DS90LV032ATMTC uses a 16-pin TSSOP package. Texas Instruments lists the DS90LV032A family as a quad LVDS receiver, while distributor records identify the MTC ordering code as a 16-TSSOP device. The 16-pin surface-mount package provides access to four differential input channels and their corresponding CMOS outputs.
Where can I download the DS90LV032ATMTC datasheet PDF?
The official DS90LV032ATMTC-family datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90lv032a.pdf. The manufacturer document describes the DS90LV032A as a 3-V LVDS quad CMOS differential line receiver. It is the primary document for pin assignments, electrical characteristics, application information, and recommended circuit implementation.
Where can I find the DS90LV032ATMTC pinout?
The DS90LV032ATMTC pinout is shown in the pin-configuration and pin-description sections of the Texas Instruments DS90LV032A datasheet at https://www.ti.com/lit/ds/symlink/ds90lv032a.pdf. Use that diagram when assigning the four LVDS input pairs, four CMOS outputs, supply pins, and grounds on the 16-pin TSSOP footprint.
What is the best drop-in replacement for DS90LV032ATMTC?
The closest documented drop-in choices are DS90LV032ATMTC/NOPB and DS90LV032ATMTCX/NOPB, which retain the 16-pin TSSOP interface and 400-Mbps receiver function. The most important distinction is terminal-finish and lead-free configuration rather than logic functionality. Confirm package pinout, supply requirements, temperature grade, and procurement status against the manufacturer datasheet before substitution.
Can DS90LV032ATMTC replace DS90LV032ATMR?
The DS90LV032ATMTC can serve as the same device family and 16-pin TSSOP receiver in a suitable design, but the ordering suffixes must be checked before treating the substitution as production-safe. Texas Instruments ordering codes can encode package, temperature, and shipping or finish choices. Compare the full ordering-information table and datasheet limits for both exact MPNs.
DS90LV032ATMTC vs DS90LV032ATMTC/NOPB - which should I select?
The DS90LV032ATMTC and DS90LV032ATMTC/NOPB both identify a 400-Mbps, four-channel, 16-pin TSSOP LVDS receiver, but their orderable configurations differ. The /NOPB version is explicitly identified as the Pb-free configuration, while the comparison record marks the target device's RoHS code as No. Select the exact ordering option required by environmental and manufacturing requirements.
DS90LV032ATMTC vs DS90LV032ATM - what is the difference?
The DS90LV032ATMTC and DS90LV032ATM are closely related orderable forms of the DS90LV032A receiver family, and a component comparison identifies both as 400-Mbps devices in 16-pin TSSOP packages. Their exact suffix meanings must be taken from the manufacturer ordering table because the abbreviated distributor records do not expose every qualification and shipping attribute. Do not assume identical temperature or terminal-finish status without checking.
When should I choose DS90LV032ATMTC over a single-channel LVDS receiver?
Choose the DS90LV032ATMTC when the design must terminate four differential LVDS links in one package. Its four-channel organization reduces component count and simplifies synchronization of multiple point-to-point interfaces at rates above 400 Mbps. A discrete or single-channel solution may be preferable only when channel count is low, routing requirements are unusual, or a different package is already fixed by the system design.
Is DS90LV032ATMTC suitable for high-speed backplane and video links?
The DS90LV032ATMTC is suitable for high-speed balanced links when the PCB implements correct LVDS signal integrity. Its support for data rates above 400 Mbps and 3-V CMOS outputs fits point-to-point backplane, instrumentation, video-transfer, and data-acquisition interfaces. Controlled differential impedance, proper termination, and short return paths remain essential for reliable operation.
Does DS90LV032ATMTC need an external LVDS line driver?
The DS90LV032ATMTC is a receiver and requires an external differential signal source, such as the Texas Instruments DS90LV031A companion line driver. The receiver converts the low-voltage differential input into 3-V CMOS logic. A transmitter is therefore required when the PCB needs to originate the LVDS signal rather than receive it from another board or cable.
Where to buy DS90LV032ATMTC online?
Use the Request a Quote form on this XAIPART product page to request availability, order quantities, and current commercial terms for the DS90LV032ATMTC. The part is a cataloged 16-pin TSSOP receiver, but its Not Recommended for New Designs lifecycle status may constrain new-production purchasing. Supply confirmation should include the exact suffix, packaging format, and acceptable manufacturing dates.
What is the price of DS90LV032ATMTC?
The current commercial price for the DS90LV032ATMTC is best obtained through the Request a Quote form on this page. This product is listed as Not Recommended for New Designs, so quotation can depend on exact suffix, package quantity, and remaining supply. Avoid basing a production cost estimate on a historical catalog price because its purchasing basis may differ from current availability.
What is the lead time and stock status of DS90LV032ATMTC?
Request the current stock, lead time, and minimum order quantity through the Request a Quote form on this page. The DS90LV032ATMTC has a Not Recommended for New Designs lifecycle status, which can make available supply dependent on existing inventory rather than a standard new-production schedule. Include the required date code, shipping form, and order quantity in the request.

بيانات مرجعية هندسية لـ DS90LV032ATMTC — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the DS90LV032ATMTC when an existing design specifically calls for the MTC ordering code and needs a four-channel, 3-V LVDS receiver in a 16-pin TSSOP package. Choose DS90LV032ATMTC/NOPB when the same receiver function and footprint are required with a documented lead-free ordering option. Choose DS90LV032ATMTCX/NOPB when that suffix is controlled by an approved vendor or product source and its qualification attributes satisfy the program. None of these choices changes the PCB footprint or 400-Mbps electrical role, so the manufacturer ordering table remains the deciding authority. For new production, account for the target's Not Recommended for New Designs status and consider whether an actively supported interface family is more appropriate. If the original design is not already committed to this footprint, do not select a merely similar cross-brand LVDS receiver without a complete pin, voltage, timing, and signal-integrity comparison.

المقارنة مع البدائل

المعامل هذا المنتج DS90LV032ATMTC/NOPB DS90LV032ATMTCX/NOPB DS90LV032ATM
Package 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Receiver Configuration 0/4 differential receiver 0/4 receiver LVDS LVDS receiver 0/4 receiver LVDS
Number of Channels 4 channels 4 channels 4 channels 4 channels
Maximum Data Rate >400 Mbps >400 Mbps 400 Mbps 400 Mbps
Equivalent Clock Rate >200 MHz >200 MHz 200 MHz 200 MHz
Supply Voltage 3 V 3 V 3 V 3 V
Output Technology 3-V CMOS 3-V CMOS 3-V CMOS 3-V CMOS

أبرز الفروقات

  • Four high-speed LVDS channels in one compact receiver (مقابلDS90LV032ATM)
  • Identical 400-Mbps receiver performance with a documented Pb-free ordering option (مقابلDS90LV032ATMTC/NOPB)
  • Additional documented ordering suffix without a package change (مقابلDS90LV032ATMTCX/NOPB)

ملاحظات التصميم

Route every LVDS channel as a tightly coupled differential pair over a continuous reference plane. Keep the pair geometry and spacing uniform through connector transitions, avoid right-angle jogs where practical, and do not add test-probe stubs to production traces. The DS90LV032A supports rates above 400 Mbps, so impedance discontinuities and asymmetric routing can create reflections that compromise timing even when the logic appears functional.

Follow the manufacturer's recommended 3-V supply-decoupling layout and place the components close to the VCC and GND pins identified in the datasheet pinout. The receiver has two supply pins and two ground pins in the 16-pin TSSOP; connect both as shown by the reference configuration rather than treating the package as a single-pin device. Verify startup sequencing and supply tolerance against the electrical-characteristics table before using the receiver with a shared 3-V rail.

Use the application and termination guidance in the manufacturer datasheet to establish the differential termination arrangement for the complete source-to-receiver channel. Pay particular attention to the connector and cable transition, where impedance mismatch commonly appears. The receiver detects a typical 350 mV differential signal, but valid signal amplitude at its pins still depends on the driver, channel loss, termination, and system noise margin.

Do not treat DS90LV032ATMTC, DS90LV032ATMTC/NOPB, and DS90LV032ATMTCX/NOPB as interchangeable without checking the manufacturer ordering table, temperature grade, terminal finish, and ship configuration. The target is identified as Not Recommended for New Designs, while the comparison record marks its RoHS code as No. For a new environmentally constrained design, select and qualify the exact Pb-free ordering configuration rather than assuming suffix equivalence.

معلومات الامتثال

RoHS
Non Compliant
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
No
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The component comparison record marks the target's RoHS code as No and its Pb-free code as Yes only for the separately identified /NOPB ordering form. Other environmental declarations are not stated.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ds90lv032atmtc nopb ds90lv032atmtc datasheet ds90lv032atmtc pinout ds90lv032atmtc datasheet pdf ds90lv032atmtc equivalent ds90lv032atmtc replacement ds90lv032atmtc cross reference ds90lv032atmtc price ds90lv032atmtc stock Texas Instruments ds90lv032atmtc ds90lv032atmtc vs ds90lv032atm ds90lv032atmtc footprint

المكونات والمصطلحات ذات الصلة

Texas Instruments DS90LV032ATMTC DS90LV032A DS90LV031A DS90LV032ATMTC/NOPB DS90LV032ATMTCX/NOPB DS90LV032ATM LVDS Low Voltage Differential Signaling differential line receiver CMOS output digital interface IC 3-V power supply 400 Mbps data rate 200 MHz clock 350 mV differential input 16-pin TSSOP TSSOP package family surface-mount technology point-to-point interface industrial backplane data acquisition RoHS Not Recommended for New Designs
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر