NXP Semiconductors

LPC1111JHN33/103E - 50MHz Cortex-M0+ MCU | NXP

MPN: LPC1111JHN33/103E ✓ نشط
1.8 V to 3.6 V Vdss 32-HVQFN, 7 mm x 7 mm Package 50 MHz Speed 8 KB Memory
الحد الأدنى للطلب: 1 |

LPC1111JHN33/103E نظرة عامة

The NXP Semiconductors LPC1111JHN33/103E is an entry-level 32-bit Arm Cortex-M0+ microcontroller with a 50 MHz maximum CPU frequency, 8 KB of flash memory, and up to 2 KB of SRAM. It is packaged in a 32-HVQFN surface-mount package measuring 7 mm by 7 mm and operates from a 1.8 V to 3.6 V supply. The extended-temperature suffix identifies the industrial-temperature configuration described by NXP as active. This combination of memory, processing speed, and package size suits compact control systems that need more capability than an 8-bit MCU without the cost and complexity of a larger processor.

A microcontroller is a programmable system-on-chip that integrates a CPU core, program memory, data memory, and peripherals into one component. The LPC11xx family follows the embedded hierarchy of Arm Cortex-M0+ microcontroller, 32-bit microcontroller, embedded controller, and semiconductor. Its reduced instruction set and compact architecture target low-cost, low-power designs where deterministic control, serial communication, and general-purpose I/O are more important than high computation throughput. NXP describes the family as a cost-effective way to replace 8-bit and 16-bit control architectures.

Key characteristics include a 50 MHz clock, 8 KB flash for firmware, 2 KB SRAM for working data, and a 1.8 V to 3.6 V operating range. These figures make the device suitable for sensor controllers, compact industrial modules, and connected products that exchange data through serial interfaces. The 32-HVQFN package also supports dense PCB layouts, although its fine terminal pitch and exposed thermal pad require careful assembly planning.

The Arm Cortex-M0+ core provides a simple instruction set, efficient exception handling, and broad ecosystem support from common embedded toolchains. Peripheral integration reduces the component count of an embedded design, while the relatively small memory footprint suits straightforward control firmware. The 50 MHz operating ceiling also allows the MCU to service multiple interrupt-driven tasks without moving dedicated logic into external programmable logic.

Typical uses include industrial sensor nodes, compact motor-control helpers, building and access modules, communication equipment, and low-power IoT controllers. A product requiring USB, extensive connectivity, or substantially more code storage should evaluate a higher-pin-count or higher-memory MCU rather than assuming this entry-level device covers those requirements.

PCB implementation should follow the manufacturer's land pattern and exposed-pad recommendations. Place all decoupling capacitors close to their supply pins, route high-current outputs independently, and maintain clean return paths beneath the device. Verify the reflow profile and terminal-pad geometry against the package drawing before releasing a PCB.

This product page combines the NXP device characteristics with practical package, replacement, and design guidance. It also identifies the differences among related LPC11xx devices so engineers can determine which family member matches a required footprint, memory configuration, temperature grade, and peripheral set.

بدائل مباشرة لـ LPC1111JHN33/103E — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

LPC1111JHN33/103

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 32-HVQFN (7x7)
Same 50 MHz Cortex-M0+, 8 KB flash, 2 KB SRAM, and HVQFN footprint; temperature-grade suffix differs by up to 25% of the stated industrial range.

📋 بديل مرجعي (غير موجود في الكتالوج)

LPC1112JHN33/103

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 32-HVQFN (7x7)
Same 50 MHz Cortex-M0+ family and HVQFN footprint; flash-memory capacity differs by approximately 25% within the family configuration.

📋 بديل مرجعي (غير موجود في الكتالوج)

LPC1113JHN33/103

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 32-HVQFN (7x7)
Same 50 MHz Cortex-M0+ family and HVQFN footprint; flash-memory capacity differs by approximately 50% from the target configuration.

📋 بديل مرجعي (غير موجود في الكتالوج)

LPC1114FHN33/303

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 32-HVQFN (7x7)
Same 50 MHz Cortex-M0+ family and HVQFN footprint; flash and SRAM capacity increase by approximately 50% and 100%, respectively.

📋 بديل مرجعي (غير موجود في الكتالوج)

LPC1114FHN33/303Y

✅ بديل مباشر
📦 32-HVQFN (7x7)
Same 50 MHz Cortex-M0+ family and HVQFN footprint; flash and SRAM capacity increase by approximately 50% and 100%, respectively, with a different order suffix.

📋 بديل مرجعي (غير موجود في الكتالوج)

LPC1111JHN33/103E الحدود القصوى والخصائص الكهربائية

Product Type 32-bit microcontroller
CPU Core Arm Cortex-M0+
Maximum CPU Frequency 50 MHz
Flash Memory 8 KB
Flash Organization 8K x 8 bits
SRAM 2 KB
Operating Voltage Range 1.8 V to 3.6 V
Temperature Grade Industrial
العلبة 32-HVQFN, 7 mm x 7 mm
Terminal Count 33 terminals
نمط التركيب No-lead surface mount
Package Shape Square
Architecture ARM 32-bit
Product Series LPC1100XL
حالة دورة الحياة Active

دليل تكوين أطراف LPC1111JHN33/103E square

تكوين الأطراف لـ LPC1111JHN33/103E (حزمة square). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.

مخطط توزيع أطراف حزمة square لـ LPC1111JHN33/103E

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LPC1111JHN33/103E.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LPC1111JHN33/103E مناسب لـ 6 التطبيقs: Industrial Sensor Node, Compact Access-Control Module, Low-Power IoT Controller, Compact Motor-Control Helper, Communication Equipment Module, Building and Utility Module.

🏭

Industrial Sensor Node

The LPC1111JHN33/103E fits compact sensor nodes that periodically acquire measurements, apply filtering, and report results over a serial link. Its 50 MHz Arm Cortex-M0+ core handles interrupt-driven sampling and protocol processing, while 2 KB of SRAM provides limited working space for buffers and state variables. The 8 KB flash store supports a small embedded application rather than a large data logger. Operation from 1.8 V to 3.6 V also permits direct use of common low-voltage sensor and transceiver rails. Keep firmware lean, place the decoupling capacitors close to the supply terminals, and select an external nonvolatile memory when measurement history must survive power cycles.

🔒

Compact Access-Control Module

The LPC1111JHN33/103E can serve as the central controller in an electronic lock, credential reader, or access-control node. Its 50 MHz core supports responsive keypad scanning, status feedback, and serial communication with a reader or host. The industrial temperature grade is appropriate for equipment installed outside conditioned indoor environments, while the small 7 mm by 7 mm HVQFN footprint supports dense module designs. Security-sensitive products should add the required authentication and key-storage hardware rather than relying on general-purpose flash alone. Firmware updates should use a controlled boot process, and the layout should preserve clean ground return paths beneath the MCU and exposed thermal pad.

🧩

Low-Power IoT Controller

The LPC1111JHN33/103E is suitable for compact IoT endpoints that periodically wake, read environmental inputs, and transmit a short status message. Its Cortex-M0+ architecture offers straightforward firmware development without requiring a high-performance processor, and the 1.8 V minimum operating voltage supports energy-conscious designs using low-voltage sensors and radio modules. The 8 KB flash limit constrains application size, so protocol stacks and update mechanisms must be selected carefully. Use sleep modes where supported, avoid unused peripherals, and measure wake-up timing in the final board. External flash is preferable when over-the-air update images or extensive logging are required.

⚙️

Compact Motor-Control Helper

The LPC1111JHN33/103E can coordinate simple motor, valve, or actuator sequences where the main controller does not need to perform intensive motion mathematics. The 50 MHz core supports deterministic timer-based sequencing, fault monitoring, and communication with a higher-level controller. Its industrial temperature grade is useful in equipment exposed to variable ambient conditions. The MCU should not be assumed to drive motor power stages directly; use appropriate driver circuits, current protection, and isolation as required. Place the controller away from high-current switching paths, maintain a continuous ground reference, and validate timing with worst-case supply and temperature conditions before production release.

🌐

Communication Equipment Module

The LPC1111JHN33/103E can manage a small serial concentrator or protocol-conversion module built around a compact PCB. Its 50 MHz Arm Cortex-M0+ core is suitable for handling framed data, timers, status LEDs, and configuration commands, while the 32-HVQFN package saves board area. Firmware size and SRAM must be checked carefully because protocol conversion, diagnostics, and buffering can consume the 8 KB flash and 2 KB SRAM resources quickly. Use DMA-capable peripherals where available, isolate communication interfaces from sensitive analog sections, and provide local decoupling at every supply terminal. The package's exposed pad should be connected according to the manufacturer's thermal and electrical guidance.

🌡️

Building and Utility Module

The LPC1111JHN33/103E is appropriate for small building-automation, utility-monitoring, and equipment-control modules that collect switch states or environmental readings. The industrial temperature grade supports use in equipment subject to wider internal temperature variation, and the low-voltage operation simplifies integration with 3.3 V sensors. The limited memory favors event-driven firmware with concise data structures and no extensive local history. Include a watchdog strategy, validate brownout behavior, and implement secure firmware updates before field deployment. PCB layout should keep mains-derived or high-energy interfaces physically separated from the MCU and use a defined, low-impedance ground strategy for reliable digital control.

ملخص المنتجات الموصى بها

LPC1111JHN33/103E NXP Semiconductors يُستخدم في: Industrial Sensor Node, Compact Access-Control Module, Low-Power IoT Controller, Compact Motor-Control Helper, Communication Equipment Module, Building and Utility Module LPC1114FHN33/303Y Higher-memory LPC11xx controller option يُستخدم في: Industrial Sensor Node LPC1111JHN33/103 Related same-package controller يُستخدم في: Compact Access-Control Module LPC1112JHN33/103 Related Cortex-M0+ control option يُستخدم في: Low-Power IoT Controller, Building and Utility Module LPC1113JHN33/103 Related family member with additional memory يُستخدم في: Compact Motor-Control Helper LPC1114FHN33/303 Higher-memory protocol controller option يُستخدم في: Communication Equipment Module
What is the LPC1111JHN33/103E?
The LPC1111JHN33/103E is an active NXP Semiconductors 32-bit Arm Cortex-M0+ microcontroller rated for up to 50 MHz operation. According to the NXP LPC11xx product information, the family targets low-cost replacements for 8-bit and 16-bit controllers by combining a 32-bit core with a simple instruction set and compact code footprint. This specific device contains 8 KB of flash memory and is offered in a 32-HVQFN package measuring 7 mm by 7 mm.
What are the key specifications of LPC1111JHN33/103E?
The LPC1111JHN33/103E combines a 50 MHz Arm Cortex-M0+ core, 8 KB flash memory, 2 KB SRAM, and a 1.8 V to 3.6 V supply range in a 32-HVQFN package. NXP identifies the LPC11xx family as an entry-level platform for replacing 8-bit and 16-bit microcontroller designs. Its 33-terminal no-lead package supports dense layouts, while the 50 MHz clock provides adequate performance for control loops, serial communication, and event-driven embedded firmware.
Where can I download the LPC1111JHN33/103E datasheet PDF?
The official LPC1111JHN33/103E datasheet is available through the NXP part page at https://www.nxp.com/part/LPC1111JHN33. Select the Data Sheet link for the primary manufacturer document and use the package drawings and pin-description sections for PCB and firmware implementation. NXP’s LPC11xx family information also describes the 50 MHz maximum operating frequency and the intended low-cost 8-bit and 16-bit migration use case.
Where can I find the LPC1111JHN33/103E pinout?
Use the package drawing and pin description in the official NXP LPC1111JHN33 datasheet to locate every terminal and the exposed pad. The device uses a 33-terminal, no-lead square package identified in product records as 32-HVQFN (7x7). The exposed thermal pad is not an ordinary signal terminal and must be connected according to the manufacturer land-pattern guidance. Do not infer the pinout solely from a generic QFN drawing because HVQFN terminal assignments are device-specific.
What voltage does LPC1111JHN33/103E operate at?
The LPC1111JHN33/103E operates from 1.8 V to 3.6 V. The 1.8 V minimum supports low-voltage embedded systems, while the 3.6 V maximum aligns with common 3.3 V supply rails. Component listings identify the device as an industrial-temperature part. The exact reset, clock, and peripheral operating conditions should be checked in the manufacturer datasheet before the supply rail is finalized.
Is LPC1111JHN33/103E suitable for industrial control systems?
The LPC1111JHN33/103E is suitable for many compact industrial control applications because it is identified as an industrial-temperature-grade, 32-bit microcontroller with a 50 MHz Arm Cortex-M0+ core. Its 8 KB flash and 2 KB SRAM suit focused control, acquisition, and communication firmware rather than resource-intensive applications. The 7 mm by 7 mm HVQFN package also allows placement close to sensors, actuators, and communication components.
How much memory does LPC1111JHN33/103E have?
The LPC1111JHN33/103E has 8 KB of flash memory, organized as 8K x 8 bits, and 2 KB of SRAM. NXP describes the LPC11xx family as a low-cost 32-bit platform intended to deliver reduced code size and simple programming. The 8 KB figure includes the space required by the bootloader, vector table, application code, and constants, so final firmware capacity is lower than the nominal flash total.
What can replace LPC1111JHN33/103E?
The closest drop-in candidates are related LPC11xx devices that use the same 32-HVQFN footprint, including LPC1112JHN33/103, LPC1113JHN33/103, and LPC1114FHN33/303Y. A mechanical footprint match is not enough for a production substitution: flash capacity, SRAM, peripherals, clock behavior, and temperature requirements must also match the original design. Verify every affected peripheral and startup function against the manufacturer data sheet before approving a replacement.
Is LPC1111JHN33/103E the same as LPC1114FHN33/303Y?
The LPC1111JHN33/103E and LPC1114FHN33/303Y are related LPC11xx microcontrollers, but they are not necessarily interchangeable. Both are associated with the HVQFN family, while the LPC1114 position in the product line generally provides a larger memory configuration. Confirm flash size, SRAM, peripheral allocation, timing, and pin-level behavior in the manufacturer documentation. Treat the LPC1114 only as a candidate when those functions are verified for the target PCB.
When should I choose LPC1111JHN33/103E over LPC1114FHN33/303Y?
Choose LPC1111JHN33/103E when the design needs only 8 KB flash, 2 KB SRAM, and the resources assigned to the entry-level LPC11xx configuration. Consider LPC1114FHN33/303Y when the firmware, working data, or peripheral requirements exceed those limits while retaining the same family architecture. The deciding factor is functional margin rather than CPU branding: calculate firmware utilization and peripheral needs before making the selection.
Where can I buy LPC1111JHN33/103E online?
The LPC1111JHN33/103E can be requested through the Request a Quote form on this page. The form lets buyers specify quantity, target delivery schedule, and packaging requirements while the supplier confirms current availability and sourcing conditions. NXP lists the base LPC1111JHN33 device as active, but production planning should still confirm the exact LPC1111JHN33/103E order code and its delivery status.
What is the price of LPC1111JHN33/103E?
Current commercial terms for LPC1111JHN33/103E should be obtained through the Request a Quote form on this page. The form is the appropriate channel for checking quantity pricing, stock allocation, and lead time because component pricing can change with order volume and market conditions. Provide the exact LPC1111JHN33/103E suffix and required package quantity so the quotation matches the intended production order.
What is the lead time for LPC1111JHN33/103E?
Request the current lead time for LPC1111JHN33/103E through the Request a Quote form on this page. Include your required order quantity, target shipment date, and approved manufacturer list of authorized suppliers in the request. NXP identifies the LPC1111JHN33 product as active, but an active product status does not by itself establish allocation, inventory, or a delivery date for every package configuration.
Is LPC1111JHN33/103E in stock?
Use the Request a Quote form on this page to request current LPC1111JHN33/103E stock and lead-time confirmation. NXP lists the base LPC1111JHN33 device as active, which supports continued sourcing planning, but live inventory can vary by order code and order quantity. State the exact suffix LPC1111JHN33/103E in the request to avoid receiving a quotation for a related package or temperature variant.
Does LPC1111JHN33/103E support RoHS and AEC-Q100?
The LPC1111JHN33/103E has a documented industrial temperature grade, but its RoHS, REACH, lead-free, halogen-free, and AEC-Q100 classifications must be confirmed from the current manufacturer product documentation before release. The /103E suffix denotes the extended-temperature order configuration and should not be interpreted by itself as automotive qualification. Request the applicable NXP compliance declaration for the exact assembled order code.

بيانات مرجعية هندسية لـ LPC1111JHN33/103E — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LPC1111JHN33/103E for compact control products whose firmware fits within 8 KB flash and 2 KB SRAM and whose operating voltage falls between 1.8 V and 3.6 V. Its 50 MHz Arm Cortex-M0+ core is appropriate for sensor acquisition, serial communication, access-control modules, and basic industrial control. Choose LPC1112JHN33/103 or LPC1113JHN33/103 when the same family and footprint are required but additional flash is needed. Choose LPC1114FHN33/303 or LPC1114FHN33/303Y when the design requires 32 KB flash and 4 KB SRAM; the /303Y order code is the better-defined industrial-temperature candidate among those listed. Before approving any replacement, verify the exact pin assignments, peripheral allocation, clock limits, startup behavior, thermal grade, and exposed-pad requirements against the manufacturer documentation. A common package is necessary for PCB reuse, but it does not establish complete functional equivalence.

المقارنة مع البدائل

المعامل هذا المنتج LPC1111JHN33/103 LPC1112JHN33/103 LPC1113JHN33/103 LPC1114FHN33/303 LPC1114FHN33/303Y
Package 32-HVQFN (7x7) 32-HVQFN (7x7) 32-HVQFN (7x7) 32-HVQFN (7x7) 32-HVQFN (7x7) 32-HVQFN (7x7)
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
CPU Core Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+
Maximum CPU Frequency 50 MHz 50 MHz 50 MHz 50 MHz 50 MHz 50 MHz
Flash Memory 8 KB 8 KB 12 KB 16 KB 32 KB 32 KB
SRAM 2 KB 2 KB 4 KB 4 KB 4 KB 4 KB
Operating Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V
Terminal Count 33 terminals 33 terminals 33 terminals 33 terminals 33 terminals 33 terminals

أبرز الفروقات

  • Entry-level memory configuration supports focused control firmware (مقابلLPC1114FHN33/303Y)
  • Maintains the same maximum clock performance across the compared LPC11xx options (مقابلLPC1112JHN33/103)
  • Documented industrial-temperature classification (مقابلLPC1114FHN33/303)

ملاحظات التصميم

Follow the NXP package land pattern exactly, including the exposed-pad geometry and solder-mask design. Place the MCU close to its supply bypassing network and use the shortest practical ground return from each capacitor. Avoid routing high-current motor, relay, or switching-converter paths beneath the HVQFN because coupled currents can disturb sensitive digital and analog measurements.

Decouple each supported supply domain with the capacitance and placement required by the manufacturer datasheet. Verify startup, brownout, and operating behavior across the complete 1.8 V to 3.6 V range rather than testing only at 3.3 V. If an external regulator powers the MCU, include adequate transient margin for the 50 MHz switching activity and keep the supply return continuous through the exposed pad.

The exposed thermal pad is the primary path for heat transfer and must be connected to the PCB ground structure according to the manufacturer drawing. Provide uninterrupted copper beneath and around the package rather than relying on a single thermal via. Although the LPC1111JHN33/103E has relatively low processing power, thermal performance still matters in enclosed equipment with an elevated ambient temperature.

Do not treat the 32-HVQFN footprint as a generic 32-pin QFN. The listed device has 33 terminals and a device-specific exposed-pad arrangement. Check the LPC111x pin-description table for alternate functions, debug access, reset, clock, and power connections before finalizing tracks. A footprint-library substitution can compile successfully while producing an electrically incorrect board.

Keep sensitive sensor inputs and communication interfaces away from switching nodes and high-current outputs. Maintain short, symmetric clock paths and provide clean ground references for every external interface. If the board combines analog sensing with the MCU, separate analog and digital return currents where practical and connect them at a controlled ground point. Validate signal integrity with the actual transceiver, connector, and enclosure arrangement.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The device is identified as industrial-temperature, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact order code. Confirm current compliance documents with NXP before production release.

تم التحقق من البيانات في: 2026-11-20 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LPC1111JHN33/103E datasheet LPC1111JHN33/103E pinout LPC1111JHN33/103E datasheet pdf LPC1111JHN33/103E equivalent LPC1111JHN33/103E replacement LPC1111JHN33/103E footprint LPC1111JHN33/103E price LPC1111JHN33/103E stock NXP LPC1111JHN33/103E LPC1111JHN33/103E HVQFN33 LPC1111JHN33/103E vs LPC1114FHN33/303Y LPC1111JHN33/103E application circuit

المكونات والمصطلحات ذات الصلة

NXP Semiconductors LPC1111JHN33/103E LPC1111JHN33 LPC1111JHN33/103 LPC1112JHN33/103 LPC1113JHN33/103 LPC1114FHN33/303 LPC1114FHN33/303Y Arm Cortex-M0+ Arm Cortex-M0 32-bit microcontroller embedded controller semiconductor LPC11xx 8 KB flash memory 2 KB SRAM 50 MHz clock 32-HVQFN HVQFN package family QFN family surface-mount package SMD industrial temperature grade industrial sensor node IoT controller
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر