Texas Instruments

LT1001ACP - Precision 0.8 MHz Op Amp in 8-PDIP | Texas Instruments

MPN: LT1001ACP ✓ نشط
60 uV maximum Vdss 8-pin PDIP Package
الحد الأدنى للطلب: 1 |

LT1001ACP نظرة عامة

Texas Instruments LT1001ACP is a precision, general-purpose operational amplifier with one amplifier circuit per package, a maximum input offset voltage of 60 uV, and a gain-bandwidth product of 0.8 MHz. The device is supplied in an 8-pin PDIP package for through-hole PCB installation.

An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set its closed-loop behavior. The LT1001 belongs to the broader hierarchy of linear amplifier, analog IC, and semiconductor devices. Its low offset specification makes it useful when the difference between two input voltages must be measured or amplified accurately, while its 0.8 MHz bandwidth supports moderate-frequency signal paths rather than high-speed applications.

The principal features of the LT1001ACP include a 60 uV maximum input offset voltage, a 0.8 MHz gain-bandwidth product, one amplifier per package, and an 8-pin PDIP package. The through-hole package provides generous pin spacing and mechanical robustness for prototypes, educational systems, laboratory equipment, and selected production boards that are not constrained to surface-mount assembly.

The LT1001 uses precision bipolar operational-amplifier circuitry. Its offset-trim terminals support factory or user-level offset adjustment, while the amplifier provides the differential input and feedback connections required for inverting, non-inverting, summing, filtering, and instrumentation configurations. Exact input bias current, slew rate, supply-current, common-mode range, output swing, and temperature limits are not stated on the accessible manufacturer product listing and should be confirmed against the LT1001 manufacturer data sheet before final circuit sign-off.

Typical uses include low-level signal conditioning, bridge and transducer front ends, precision current-loop interfaces, laboratory instrumentation, audio and control circuits, sensor amplification, and active filtering. The 0.8 MHz bandwidth makes it appropriate for signal bandwidths below that limit when slew-rate and gain requirements are also acceptable.

When designing a board around the LT1001ACP, check the 8-pin PDIP pinout and leave adequate clearance around the package for conventional DIP sockets or leaded soldering. Keep feedback resistors and sensitive input traces away from switching nodes, provide local supply bypassing, and verify the required output swing at the selected supply voltage before committing the schematic.

This product page combines manufacturer specifications, package information, sourcing guidance, verified alternatives, and practical design notes to support component selection and PCB planning for the LT1001ACP.

بدائل مباشرة لـ LT1001ACP — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

LT1001ACN8

✅ بديل مباشر
📦 PDIP-8
Order-code difference of 0%; verify the package drawing, electrical grade, and temperature suffix before substitution

📋 بديل مرجعي (غير موجود في الكتالوج)

FT1001ACN8

✅ بديل مباشر
📦 PDIP-8
Alternative manufacturer; offset and bandwidth differences are not quantified in the comparison record and require data-sheet validation

📋 بديل مرجعي (غير موجود في الكتالوج)

LT1001ACP الحدود القصوى والخصائص الكهربائية

Device Type Precision operational amplifier
Amplifier Circuit Count 1 circuit
Input Offset Voltage 60 uV maximum
Gain-Bandwidth Product 0.8 MHz
Package Type 8-pin PDIP
Pitch 0.300 inch
نمط التركيب Through-hole
Product Classification Standard general-purpose amplifier
Offset Adjustment Dedicated trim pins

دليل تكوين أطراف LT1001ACP 8-pin pdip

تكوين الأطراف لـ LT1001ACP (حزمة 8-pin pdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pin pdip لـ LT1001ACP

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LT1001ACP.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LT1001ACP مناسب لـ 6 التطبيقs: Precision Sensor Signal Conditioning, Laboratory Instrumentation, Active Filtering, Current-Loop Signal Interface, Audio Control and Buffering, Educational and Prototype Circuits.

🧩

Precision Sensor Signal Conditioning

The LT1001ACP fits low-level sensor front ends because its maximum input offset voltage is 60 uV, reducing the systematic error introduced when amplifying a small differential signal. A practical design uses the device in a non-inverting or differential configuration, with the sensor connected to the input pins and feedback defining the gain. The 0.8 MHz gain-bandwidth product supports moderate-bandwidth sensors rather than fast transient capture. Before finalizing the circuit, verify input bias current, common-mode range, output swing, and noise against the sensor impedance and supply voltage.

🔧

Laboratory Instrumentation

The LT1001ACP is appropriate for laboratory instrumentation that amplifies low-level analog signals in a through-hole prototype or socketed assembly. Its 60 uV maximum offset and single-amplifier configuration make it useful for bridge, buffer, and gain-stage designs where offset contributes directly to measurement uncertainty. The 8-pin PDIP package also simplifies hand assembly and replacement. The designer should verify supply-voltage limits, input bias current, output swing, and frequency response in the final measurement circuit rather than assuming that the headline offset and bandwidth specifications cover every operating condition.

🌐

Active Filtering

The LT1001ACP can implement active low-pass, high-pass, or notch stages when the desired signal bandwidth is comfortably below its 0.8 MHz gain-bandwidth product. Stable closed-loop gain and suitable noise performance remain important when selecting component values around the amplifier. Place feedback components close to the relevant pins and keep sensitive nodes away from clocked and switching circuits. Because the accessible family listing does not state slew rate, gain-bandwidth margin rules, or output-current capability, verify those values in the manufacturer data sheet before choosing very high Q-factor filters or demanding drive loads.

🏭

Current-Loop Signal Interface

The LT1001ACP is suitable for buffering and signal conditioning in industrial current-loop interfaces when the loop bandwidth remains well below 0.8 MHz. Its precision offset rating helps preserve small voltage information at the input, while the standard 8-pin PDIP package supports legacy industrial and laboratory boards. The circuit must also satisfy the interface amplifier's common-mode and output-swing requirements, which are not stated in the accessible manufacturer summary. Confirm those limits, supply sequencing, input protection, and isolation boundaries before connecting field wiring.

🎧

Audio Control and Buffering

The LT1001ACP can serve as a general-purpose precision buffer or low-frequency active gain stage in audio-control and instrumentation paths. Its 60 uV maximum input offset and 0.8 MHz gain-bandwidth product are compatible with moderate-bandwidth control signals, although they do not indicate suitability for high-fidelity audio output stages. Designers should use the device for error-amplifier, monitoring, or low-level buffer functions rather than driving speakers directly. Check noise, slew rate, output swing, and stability with the actual feedback network and load before production use.

📱

Educational and Prototype Circuits

The LT1001ACP is a practical choice for educational and prototype circuits because it combines a standard 8-pin PDIP package with precision analog characteristics. Students can experiment with inverting amplifiers, differential amplifiers, integrators, oscillators, and filters while using a conventional breadboard or socket. The 60 uV maximum offset provides a concrete precision parameter for classroom analysis, and the 0.8 MHz bandwidth makes it easier to relate circuit behavior to the operating region. Before energizing a prototype, confirm the required supply rails and all eight pin assignments from the manufacturer data sheet.

What are the key specifications of LT1001ACP that engineers should know?
The LT1001ACP is a precision, single-amplifier operational amplifier with a maximum input offset voltage of 60 uV and a gain-bandwidth product of 0.8 MHz. According to the manufacturer LT1001 product page, it is a production precision operational amplifier available in an 8-pin PDIP configuration. These figures position it for accurate low-level signal conditioning rather than wideband or high-speed amplification.
What is the operating voltage range of LT1001ACP?
The accessible manufacturer listing confirms that the LT1001 is a production precision operational amplifier but does not state its operating supply-voltage range. Before connecting the 8-pin PDIP device, consult the pin-configuration and electrical-characteristics tables in the LT1001 manufacturer data sheet. Confirm both the positive and negative supply limits and the common-mode operating range for the intended circuit.
Where can I download the LT1001ACP datasheet PDF?
The LT1001ACP data-sheet information is available from the Analog Devices LT1001 manufacturer product page, which provides the family documentation and product-selection resources for the precision operational amplifier. The distributor search result also identifies the device as an 8-PDIP Texas Instruments part. Use the manufacturer page for the authoritative PDF and verify that the document includes the PDP-8 package option.
Where can I find the LT1001ACP pinout?
The LT1001ACP uses an 8-pin PDIP package, and the manufacturer data sheet is the authoritative source for assigning signals to all eight pins. The available circuit discussion identifies pins 1 and 8 as offset-trim terminals and pin 5 as NC. Assign the input, output, supply, and remaining trim functions only after cross-checking the pin-description table for the 8-PDIP configuration.
Can LT1001ACP be used for precision sensor amplification?
Yes, the LT1001ACP can be used for precision sensor amplification because its maximum input offset voltage is 60 uV. The device is a single-amplifier, 0.8 MHz precision op amp in an 8-pin PDIP package. Suitability still depends on sensor impedance, source noise, input bias current, supply voltage, and the required signal bandwidth, all of which must be checked against the family data sheet.
Where can I buy LT1001ACP online?
Use the Request a Quote form on this page to request LT1001ACP availability, current lot information, and a commercial quotation. The manufacturer product page confirms the LT1001 family is in production, while distributor listings identify the exact 8-PDIP LT1001ACP configuration. A quotation request provides the appropriate route for current stock, lead time, and order handling without relying on a static listing.
What is the price of LT1001ACP?
Current LT1001ACP pricing is best obtained through the Request a Quote form on this page because commercial terms, order quantity, and supply status can change. The LT1001ACP is an 8-pin PDIP precision op amp with a 60 uV maximum input offset voltage and a 0.8 MHz gain-bandwidth product. Request the exact suffix and package when seeking a quotation.
What is the lead time for LT1001ACP?
Request the current lead time through the Request a Quote form on this page. The Analog Devices LT1001 product page identifies the family as production, and distributor records identify the LT1001ACP in an 8-PDIP package. Actual lead time depends on required quantity, lot status, quality documentation, and shipment destination, so it should be confirmed for each order.
Is LT1001ACP in stock?
The Request a Quote form on this page is the appropriate route for confirming current LT1001ACP stock and scheduled delivery. The manufacturer identifies the LT1001 family as production, while distributor search listings include the exact LT1001ACP suffix and 8-PDIP package. Inventory status should be checked against the quantity and lot requirements entered in the quotation request.
LT1001ACP vs LT1001ACN8 - which is better for a legacy through-hole design?
Both identifiers refer to the LT1001 precision op-amp family in an 8-pin PDIP-style configuration, but the ACP and ACN8 order codes should still be checked for grade and package-code differences before substitution. The LT1001ACP has a 60 uV maximum input offset voltage and 0.8 MHz bandwidth. Use the manufacturer ordering information to confirm electrical grade, temperature range, and the exact package drawing.
When should I choose LT1001ACP instead of a faster operational amplifier?
Choose the LT1001ACP when low offset, general-purpose precision amplification and an 8-pin PDIP package matter more than high bandwidth. Its stated gain-bandwidth product is 0.8 MHz, so it is better suited to moderate-bandwidth instrumentation than signal chains requiring MHz-range performance. Select a faster amplifier only when the signal bandwidth and slew-rate requirements justify the additional power and noise trade-offs.
Is LT1001ACP suitable for laboratory and test instrumentation?
The LT1001ACP is suitable for many laboratory and test-instrumentation signal paths because it combines a 60 uV maximum input offset voltage with a 0.8 MHz gain-bandwidth product in an 8-pin PDIP package. The through-hole format is convenient for prototypes and socketed assemblies. Verify supply range, input bias current, output swing, noise, and temperature limits for the exact operating conditions.
What can replace LT1001ACP as a drop-in part?
LT1001ACN8 is the closest identified 8-pin PDIP-family candidate for a drop-in evaluation, but it must be verified against the manufacturer ordering table for electrical grade and package-code changes. A public cross-reference also identifies FT1001ACN8 for comparison, although its detailed electrical and pin compatibility must be independently confirmed. Do not approve a replacement without checking offset, bandwidth, supply range, and every pin.
What is the best Analog Devices equivalent for LT1001ACP?
The LT1001ACN8 is the most directly identified Analog Devices-family alternative because the manufacturer page covers the LT1001 family and the cross-reference record points to an 8-pin PDIP order code. The LT1001ACP and LT1001ACN8 share the 60 uV maximum offset and 0.8 MHz bandwidth family positioning, subject to package and grade verification. Confirm pin functions and ordering details before replacement.
Is LT1001ACP the same as FT1001ACN8?
No equivalence should be assumed without validation. A public comparison record places LT1001ACP beside FT1001ACN8, but it does not establish identical electrical ratings or pin behavior. The LT1001ACP is specified as a 60 uV-maximum-offset, 0.8 MHz precision op amp in an 8-PDIP. Review the FT1001ACN8 data sheet for pinout, offset, bandwidth, supply range, and package tolerances.

بيانات مرجعية هندسية لـ LT1001ACP — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the LT1001ACP when the design needs a single precision op amp with a 60 uV maximum input offset voltage, moderate bandwidth up to the 0.8 MHz gain-bandwidth limit, and an 8-pin PDIP footprint. It is especially practical for prototypes, laboratory instrumentation, sensor interfaces, and legacy through-hole boards. LT1001ACN8 is the priority alternative to evaluate because it remains within the documented LT1001 family and shares the stated key ratings; nevertheless, confirm the exact package drawing, temperature grade, and ordering suffix. Consider FT1001ACN8 only after checking its full data sheet for offset, bandwidth, supply range, common-mode range, output swing, and pin functions. For signals significantly above 0.8 MHz, high closed-loop gain, or demanding slew-rate requirements, select a higher-bandwidth amplifier rather than forcing the LT1001ACP beyond its intended operating region.

المقارنة مع البدائل

المعامل هذا المنتج LT1001ACN8 FT1001ACN8
Brand Texas Instruments Analog Devices Force Technologies Ltd
Package 8-pin PDIP PDIP-8 PDIP-8

أبرز الفروقات

  • Precision offset specification for low-level signal work (مقابلFT1001ACN8)
  • Single amplifier in a standard through-hole package (مقابلFT1001ACN8)
  • Family continuity for precision instrumentation (مقابلFT1001ACN8)

ملاحظات التصميم

Assign every connection from the manufacturer pin-description table before routing the board. The available circuit record identifies pins 1 and 8 as offset-trim terminals and pin 5 as NC; do not connect a signal or supply to pin 5. For a conventional PDIP layout, preserve adequate body clearance for soldering, socketing, and mechanical tolerance.

Treat the 0.8 MHz gain-bandwidth product as the principal bandwidth limit, not as a guarantee of usable closed-loop bandwidth at every gain. High closed-loop gain reduces bandwidth and may alter stability requirements. Confirm the intended gain, signal spectrum, slew rate, and load against the LT1001 family documentation before finalizing the feedback network.

Keep the input and offset-trim nodes compact and away from digital switching traces. Place feedback resistors close to the amplifier pins to minimize parasitic capacitance and noise pickup. Use short, direct supply connections and local bypassing, while observing the manufacturer's polarity and grounding recommendations for the selected bipolar or single-supply configuration.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The accessible manufacturer product listing identifies the LT1001 as a production precision operational amplifier but does not provide component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

lt1001 pdf LT1001ACP datasheet LT1001ACP datasheet pdf LT1001ACP pinout LT1001ACP specifications Texas Instruments LT1001ACP LT1001ACP PDIP-8 amplifier LT1001ACP 60 uV offset LT1001ACP 0.8 MHz amplifier LT1001ACP replacement LT1001ACP vs LT1001ACN8 LT1001ACP drop-in equivalent LT1001ACP price LT1001ACP stock LT1001ACP sensor amplifier

المكونات والمصطلحات ذات الصلة

Texas Instruments Analog Devices LT1001ACP LT1001ACN8 FT1001ACN8 LT1001 precision operational amplifier operational amplifier op amp analog IC linear amplifier semiconductor voltage-feedback amplifier input offset voltage gain-bandwidth product offset trim PDIP-8 through-hole package precision instrumentation sensor signal conditioning active filter current-loop interface
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر