LT1179CJ - 17uA Quad Precision Op Amp | Analog Devices
MPN: LT1179CJ ✗ انتهى عمره الإنتاجيLT1179CJ نظرة عامة
A precision operational amplifier is a low-noise, high-gain analog signal-conditioning device used to amplify weak sensor, instrumentation, control, and feedback signals. The LT1179CJ belongs to the micropower operational-amplifier category, combining four amplifiers in one package with very low supply-current demand. This makes it suitable for battery-powered instrumentation and other systems where amplifier power consumption must remain small.
The LT1179CJ is specified as a general-purpose, four-circuit amplifier. Its precision characteristics include low offset voltage, low offset current, and low input bias current, helping reduce signal error when the amplifier is used with sensors, transducers, or high-impedance sources. The device is intended for single-supply systems, where the output signal must be biased above ground, as well as conventional dual-supply circuits using ±15V.
The LT1179CJ can be used in low-power sensor interfaces, precision signal-conditioning circuits, instrumentation amplifiers, data-acquisition front ends, battery-powered measurement systems, and low-current feedback loops. Its 17uA-per-amplifier maximum supply current is particularly useful when four active amplifiers would otherwise contribute a larger aggregate supply-current requirement.
For single-supply operation, confirm the input and output common-mode range, output swing, and load requirements against the manufacturer datasheet before finalizing the biasing network. Decoupling capacitors should be placed close to the power pins, and unused amplifier channels should be configured according to the recommended stable-output method.
This product page combines the manufacturer product information, distributor package identification, and application-oriented engineering guidance. Use the official Analog Devices datasheet for the complete electrical characteristics, pin assignments, ordering information, and test conditions.
بدائل مباشرة لـ LT1179CJ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلLT1179CJ الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Precision operational amplifier |
| Number of Circuits | 4 circuits |
| Supply Current per Amplifier | 17uA maximum |
| Offset Voltage | 70uV maximum |
| Offset Current | 250pA maximum |
| Input Bias Current | 5nA maximum |
| Optimized Supply Voltage | 5V single supply |
| Additional Supply Specification | ±15V supplies |
| العلبة | 14-pin CERDIP (0.300 inch, 7.62mm) |
| نوع التركيب | Through-hole |
| عدد الدبابيس | 14 pins |
| Temperature Grade | Commercial |
| Product Classification | General-purpose amplifier |
دليل تكوين أطراف LT1179CJ 14-pin cerdip (0.300 inch, 7.62mm)
تكوين الأطراف لـ LT1179CJ (حزمة 14-pin cerdip (0.300 inch, 7.62mm)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LT1179CJ.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LT1179CJ مناسب لـ 6 التطبيقs: Battery-Powered Sensor Interfaces, Precision Data-Acquisition Front Ends, Portable Measurement Instruments, Low-Current Feedback Control, Precision Bridge and Transducer Amplification, Low-Power Industrial Signal Conditioning.
Battery-Powered Sensor Interfaces
The LT1179CJ suits low-level sensor conditioning where four analog channels must operate from a constrained power budget. Its maximum supply current of 17uA per amplifier limits the contribution of the four integrated amplifiers, while 70uV maximum offset voltage and 5nA maximum input bias current help preserve small sensor signals. The amplifier is optimized for 5V single-supply operation, making it suitable for portable measurement systems that require level shifting or gain stages near the sensor. Confirm the input common-mode range and output swing against the sensor signal before finalizing the biasing network.
موصى به
Precision Data-Acquisition Front Ends
The four amplifiers in the LT1179CJ can provide gain, filtering, level shifting, and drive functions close to a sensor or converter input. Its maximum offset voltage of 70uV, offset current of 250pA, and input bias current of 5nA are useful where amplifier-generated errors would be significant relative to the measured signal. Operation from a single 5V rail supports compact acquisition systems, while the availability of ±15V specifications allows the same device family to fit bipolar laboratory instrumentation. Apply appropriate anti-alias filtering and verify settling behavior for the target signal bandwidth.
موصى به
Portable Measurement Instruments
The LT1179CJ is appropriate for handheld or battery-operated instruments that need several precision analog channels without allocating substantial supply current to each amplifier stage. The 17uA maximum supply current per amplifier is the central benefit, and the device's four-circuit configuration can reduce the number of packages required for gain and buffering functions. At a 5V supply, engineers can design input conditioning around transducers, resistive sensors, and control feedback while keeping system power low. The commercial-grade part and 14-pin through-hole package are particularly convenient for instrument-panel and laboratory equipment layouts that require socketed or leaded assembly.
موصى به
Low-Current Feedback Control
The LT1179CJ can implement error amplifiers, transconductance loops, and feedback elements in low-power control systems. Its precision DC characteristics help reduce output error, while the low per-amplifier supply current supports designs where continuous operation is required. Four channels provide flexibility for sensor feedback, reference buffering, and auxiliary control functions within a single 14-pin CERDIP package. For stable loop closure, check gain-bandwidth and phase-margin requirements in the manufacturer documentation and keep the compensation network close to the relevant amplifier pins.
موصى به
Precision Bridge and Transducer Amplification
The LT1179CJ can amplify the small differential outputs produced by resistive bridges and other passive transducers. Low offset voltage, low offset current, and low input bias current are important because these errors can create measurement offsets or disturb high-impedance sensor sources. The micropower operating current allows continuous bridge monitoring without making the sensor dominates the system power budget. A 5V single-supply configuration may require mid-supply biasing for bipolar sensor signals, so verify the common-mode range and output swing before selecting resistor values and operating points.
موصى به
Low-Power Industrial Signal Conditioning
The LT1179CJ is useful for conditioning slow industrial sensor signals when each channel must consume little power. A 5V supply simplifies deployment near field instrumentation, while the 70uV maximum offset voltage supports precision measurements without requiring a larger general-purpose op amp. Four integrated channels can handle inputs, filtering, and active feedback in a compact through-hole implementation. Designers should account for input protection, common-mode limits, grounding, and output drive when connecting external field wiring, and should verify the manufacturer operating-temperature limits before using the commercial-grade part in harsh environments.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LT1179CJ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
ملاحظات التصميم
The maximum supply-current specification is 17uA per amplifier, so four active channels can contribute as much as 68uA under the manufacturer's stated conditions. Include this figure when sizing the supply and calculate the total system demand from sensors, references, and digital control circuitry as well. For single-supply operation, use the 5V-optimized configuration and verify that the complete signal path remains inside the amplifier's input and output ranges.
Place the supply-decoupling capacitor close to the device power pins and provide a low-impedance return path for the ground connection. Because the LT1179CJ uses a 14-pin through-hole CERDIP package, maintain adequate spacing between adjacent pins for soldering and avoid excessive thermal stress during assembly. Follow the manufacturer package drawing for the land pattern and pin orientation rather than inferring dimensions from the distributor description.
Do not treat the 5V single-supply optimization as permission to ignore common-mode-range limitations. Confirm that source signals, bias points, and output targets remain within the usable range, particularly in battery-powered designs where the rail may sag. Also account for input bias current when driving high-impedance sources and configure unused amplifier channels according to the datasheet's stability guidance.
معلومات الامتثال
The distributor information identifies the LT1179CJ as a commercial-grade component but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not stated.
