Analog Devices

LT1630CS8 - Dual 30MHz RRIO Precision Amp | Analog Devices

MPN: LT1630CS8 ✓ نشط
Typically less than 150 μV Vdss 8-pin SOIC, 0.154 inch (3.90 mm) width Package
الحد الأدنى للطلب: 1 |

LT1630CS8 نظرة عامة

The Analog Devices LT1630CS8 is a dual precision operational amplifier with a 30 MHz gain-bandwidth product, a 10 V/μs slew rate, and rail-to-rail input and output operation in an 8-pin SOIC package. Two independent amplifier circuits provide flexible signal conditioning for instrumentation, industrial controls, sensor interfaces, and low-voltage analog systems. The LT1630 family is listed in production by Analog Devices and is designed for applications requiring higher bandwidth than general-purpose amplifiers while retaining precise DC behavior.

An operational amplifier is a voltage-gain amplifier whose open-loop gain is very high at low frequencies. Negative feedback shapes the closed-loop response according to the surrounding resistor network. The LT1630CS8 belongs to the precision operational amplifier hierarchy, combining low offset voltage, wide bandwidth, fast slew rate, and rail-to-rail signal capability. Rail-to-rail input operation accommodates signals near either supply rail, while rail-to-rail output operation increases usable output range on low-voltage supplies.

Key characteristics include a 30 MHz gain-bandwidth product, a 10 V/μs slew rate, and typical input offset voltage below 150 μV. These figures make the device suitable for precision feedback networks, current-to-voltage conversion, and signal paths where input and output excursions require more range than a conventional amplifier operating strictly between the supply rails. The dual configuration reduces the component count when two similar analog channels are needed on one board.

The wide bandwidth permits operation as a general-purpose amplifier, instrumentation stage, buffer, or active filter element. Its 10 V/μs slew rate supports faster signal transitions than many precision amplifiers, although gain-bandwidth, output-voltage swing, load, and supply voltage must all be considered when defining the usable signal range. The typical offset-voltage specification below 150 μV is particularly relevant to closed-loop DC accuracy because input offset voltage contributes directly to output error after multiplication by the closed-loop noise gain.

Typical applications include bridge and thermocouple sensor interfaces, current measurement, low-level signal conditioning, industrial process controls, audio preamplifier stages, and active filters. The two channels can process related or independent signals when their supply and ground connections are common. For instrumentation designs, the rail-to-rail inputs help preserve signal integrity when the source voltage approaches the supply limits.

PCB design should keep input and feedback traces short, place compensation or decoupling components close to the associated pins, and maintain a return path for every high-frequency current. The unused amplifier channel should be configured according to the manufacturer recommendations rather than left floating. Stable feedback-network layout is particularly important because 30 MHz bandwidth can amplify parasitic delay, probe capacitance, and excessive board coupling.

This product page combines the manufacturer’s operating characteristics, package information, sourcing paths, documented drop-in candidates, and practical design guidance. It also distinguishes verified device specifications from parameters that require confirmation from the LT1630 datasheet, helping engineers plan sourcing and PCB qualification before committing a dual precision amplifier to a new design.

بدائل مباشرة لـ LT1630CS8 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

LT1630CN8

✅ بديل مباشر
📦 8-pin SOIC
Same LT1630-family 30 MHz gain-bandwidth product, 10 V/μs slew rate, and 8-pin SOIC format; the exact temperature-grade and ordering differences require datasheet confirmation.

📋 بديل مرجعي (غير موجود في الكتالوج)

LM7332MA

✅ بديل مباشر
📦 8-pin SOP
Listed as an 8-pin SOP alternative with the same package format; its offset voltage, bandwidth, slew rate, and supply limits differ by amounts not stated in the cross-reference listing.

📋 بديل مرجعي (غير موجود في الكتالوج)

LT1630CS8 الحدود القصوى والخصائص الكهربائية

Amplifier Type General-purpose precision operational amplifier
Number of Circuits 2 circuits
Gain-Bandwidth Product 30 MHz
Slew Rate 10 V/μs
Input Offset Voltage Typically less than 150 μV
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
العلبة 8-pin SOIC, 0.154 inch (3.90 mm) width
نوع التركيب Surface mount
Production Status Production

تكوين أطراف LT1630CS8

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
دبوس 1 OUT A — Amplifier A output
دبوس 2 -IN A — Inverting input for amplifier A
دبوس 3 +IN A — Non-inverting input for amplifier A
دبوس 4 V- — Negative supply connection
دبوس 5 +IN B — Non-inverting input for amplifier B
دبوس 6 -IN B — Inverting input for amplifier B
دبوس 7 OUT B — Amplifier B output
دبوس 8 V+ — Positive supply connection

التطبيقات النموذجية

LT1630CS8 مناسب لـ 6 التطبيقs: Bridge Sensor Signal Conditioning, Precision Current Measurement, Industrial Process Control, Active Filter and Frequency Shaping, Audio Preamplifier Stage, Low-Level Sensor Interface.

🏭

Bridge Sensor Signal Conditioning

The LT1630CS8 suits bridge-based pressure, load, and position sensing because each of its two amplifier channels can provide low-offset differential signal conditioning. With a 30 MHz gain-bandwidth product and typical input offset voltage below 150 μV, the device supports closed-loop measurement circuits that must preserve small differential signals while rejecting common-mode variation. Its 10 V/μs slew rate also allows relatively rapid settling through resistive feedback networks. Place the amplifier close to the bridge and feedback resistors to minimize differential pickup. Check the complete power-supply range, input common-mode limits, and bridge excitation voltage before the layout is released.

⚡

Precision Current Measurement

The LT1630CS8 can form the signal-conditioning stage of a precision current-measurement circuit, including shunt amplifiers, current-to-voltage converters, and active filters. Its typical input offset below 150 μV limits the DC error contributed by the amplifier, while the 30 MHz gain-bandwidth product supports useful closed-loop bandwidth above the bandwidth of many precision-only amplifiers. The 10 V/μs slew rate permits faster settling after a current-step event. Select feedback resistors that preserve the required noise gain and ensure the shunt voltage remains inside the input common-mode range. The shunt itself, rather than the amplifier, usually dominates the final measurement uncertainty.

🏭

Industrial Process Control

The LT1630CS8 fits industrial process-control loops that require accurate amplifier response without abandoning rail-to-rail signal range. Its two channels can handle a sensor-conditioning stage and an output-buffer stage when they share the same supply rails. The 30 MHz gain-bandwidth product gives adequate loop bandwidth for many low-frequency control signals, while the 10 V/μs slew rate can reproduce faster command transitions more effectively than a slow precision amplifier. Maintain short feedback paths and isolate the analog input from switching circuitry. Confirm operating-temperature limits and supply tolerances for the enclosure, and follow the datasheet recommendations for decoupling and unused-channel stability.

📡

Active Filter and Frequency Shaping

The LT1630CS8 is appropriate for active filters that need more bandwidth than conventional precision op amps provide. Its 30 MHz gain-bandwidth product supports a range of moderate-frequency filter topologies, and the 10 V/μs slew rate helps preserve square-wave and transient content at practical output amplitudes. The dual package allows two filter sections or a filter plus a buffer without adding another package. Component tolerances and parasitic board capacitance become increasingly important as the closed-loop bandwidth approaches the amplifier’s operating range. Keep the inverting input and feedback component layout compact, use a stable reference topology, and verify phase margin and ringing on the assembled circuit.

🎧

Audio Preamplifier Stage

The LT1630CS8 can serve as a low-level audio preamplifier or line-stage amplifier when its 30 MHz gain-bandwidth product and 10 V/μs slew rate are appropriate for the desired bandwidth and output swing. Rail-to-rail input and output operation can be valuable in low-voltage systems where the signal occupies a large portion of the available supply range. The dual configuration permits stereo pairing or leaves a channel for a monitor function. The typical input offset below 150 μV is not the dominant audio specification, so distortion, output-current capability, load impedance, and noise should be checked separately. Configure the unused channel according to the manufacturer guidance rather than allowing it to float.

🧩

Low-Level Sensor Interface

The LT1630CS8 is useful for amplifying outputs from low-level sensors where offset error and usable input range are important. Rail-to-rail inputs allow a source close to a supply rail to be amplified more effectively than with a fixed common-mode amplifier, while the 30 MHz gain-bandwidth product supports higher-bandwidth sensing systems than a slow precision-only device. The 10 V/μs slew rate helps the output follow rapid sensor transients. Care is still required for high-impedance sources because input bias current and source noise can dominate the result. Use short guarded input traces, suitable resistor values, and clean grounding to prevent the fast amplifier from responding to board-level interference.

What is the operating voltage of LT1630CS8?
The LT1630CS8 requires the dual-supply voltage range specified in the Analog Devices LT1630 datasheet; consult the Electrical Characteristics table before selecting the operating rails. The device is a dual, rail-to-rail input and output precision operational amplifier with a 30 MHz gain-bandwidth product and 10 V/μs slew rate. Confirm the minimum and maximum supply voltages, output-current limits, and input common-mode behavior against the exact temperature grade and package ordering code.
What is the gain-bandwidth product of LT1630CS8?
The LT1630CS8 has a 30 MHz gain-bandwidth product, as stated on the Analog Devices product page and in the LT1630 datasheet. This bandwidth supports comparatively fast closed-loop operation and makes the amplifier suitable for precision signal-conditioning and active-filter applications. For a noise-gain configuration of 10, the ideal small-signal bandwidth relationship would suggest approximately 3 MHz, subject to the device’s stability, output-loading, and frequency-response limits.
What is the slew rate of LT1630CS8?
The LT1630CS8 delivers a 10 V/μs slew rate. According to the Analog Devices LT1630 datasheet, this specification governs how rapidly the output can follow a large input-driven voltage change. Slew-rate limit, rather than small-signal bandwidth, may determine performance for square waves, fast edges, and large-signal transients, so both limits should be checked when defining a signal chain.
Where can I download the LT1630CS8 datasheet PDF?
The official LT1630CS8 datasheet PDF is available from Analog Devices at the product-data link on this page. The document is titled “30MHz, 10V/μs, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps” and covers the LT1630/LT1631 family. Use the manufacturer PDF for the authoritative pin description, electrical characteristics, recommended operating conditions, and application guidance.
Where can I find the LT1630CS8 pinout?
The LT1630CS8 uses an 8-pin SOIC configuration with two operational amplifiers. Pin 1 is OUT A, pin 2 is -IN A, pin 3 is +IN A, pin 4 is V−, pin 5 is +IN B, pin 6 is -IN B, pin 7 is OUT B, and pin 8 is V+. Verify these assignments against the pin-description table in the Analog Devices datasheet before laying out or modifying a PCB.
Is LT1630CS8 suitable for low-voltage sensor interfaces?
The LT1630CS8 is well suited to low-voltage sensor-interface work when the source and output signals remain within its permitted common-mode and output ranges. Its rail-to-rail input and output characteristics maximize usable signal span, while typical input offset voltage below 150 μV supports precision measurement. The supply voltage, source impedance, settling time, and output-load conditions must still satisfy the LT1630 datasheet limits.
What is the best drop-in replacement for LT1630CS8?
LT1630CN8 is the closest same-manufacturer candidate identified in the cross-reference search because it belongs to the LT1630 family and uses the same 8-pin SOIC format. LM7332MA is a cross-brand candidate also identified in an 8-pin SOP replacement listing. Neither substitution should be approved solely from package shape: compare supply voltage, offset voltage, bandwidth, slew rate, output swing, stability, and the complete pin description before production release.
Can LM7332MA replace LT1630CS8?
LM7332MA is a candidate for evaluation as an 8-pin SOP replacement, but it is not automatically interchangeable with the LT1630CS8. A valid drop-in decision requires matching power rails, input common-mode range, output swing, offset voltage, gain-bandwidth product, slew rate, and amplifier pin functions. The Analog Devices LT1630 datasheet should remain the baseline for the existing board’s electrical and layout requirements.
What is the best Analog Devices equivalent for LT1630CS8?
LT1630CN8 is the best-identified Analog Devices-family candidate for an LT1630CS8 substitution because the cross-reference search explicitly associates it with the same LT1630 device family. Its precise electrical and temperature-grade differences should be checked in the LT1630 ordering guide and datasheet. If those differences affect the installed application, retain the original LT1630CS8 rather than treating the alternate suffix as an automatic drop-in replacement.
What can replace LT1630CS8?
The documented replacement candidates are LT1630CN8 and LM7332MA, both associated with an 8-pin small-outline package. LT1630CN8 remains within the Analog Devices LT1630 family, while LM7332MA is a cross-brand option. Before substituting either device, compare its complete pinout, supply range, offset voltage, bandwidth, slew rate, output capability, and stability against the original design’s requirements.
Is LT1630CS8 the same as LT1630CN8?
LT1630CS8 and LT1630CN8 are variants within the same LT1630 dual precision operational-amplifier family, but the ordering suffixes must not be assumed to represent identical temperature grades or commercial conditions. Both are identified with an 8-pin SOIC format. Check the Analog Devices ordering table for the exact grade, temperature range, finish, and packaging distinctions before deciding whether LT1630CN8 is a drop-in replacement.
LT1630CS8 vs LM7332MA - which is better for precision signal conditioning?
Choose LT1630CS8 when its 30 MHz gain-bandwidth product, 10 V/μs slew rate, rail-to-rail input/output operation, and typical offset voltage below 150 μV align with the required precision and speed. Choose LM7332MA only after a detailed comparison confirms comparable offset, bandwidth, supply range, output swing, and pin compatibility. The available cross-reference listing identifies LM7332MA as an 8-pin SOP alternative but does not establish identical electrical performance.
When should I choose LT1630CS8 over LT1630CN8?
Choose LT1630CS8 when the temperature grade, lifecycle, packaging, and qualification attributes associated with the CS8 ordering code match the product requirements. Choose LT1630CN8 only if its corresponding grade and electrical limits satisfy the same requirements and the manufacturer’s ordering information confirms acceptable interchangeability. For safety- or mission-critical systems, make that decision from the complete ordering table and datasheet rather than the suffix alone.
How should the unused LT1630CS8 amplifier channel be connected?
Do not leave the unused LT1630CS8 amplifier channel floating. Follow the unused-amplifier configuration in the Analog Devices datasheet, which generally requires a defined feedback connection that keeps the non-inverting input at a common-mode voltage within the amplifier’s operating region. This prevents input-stage behavior from becoming undefined and reduces unwanted noise, oscillation, or interference with the active channel.
What are the key specifications of LT1630CS8 that engineers should know?
The LT1630CS8 is a production-status, dual precision operational amplifier in an 8-pin SOIC package. Its headline characteristics are a 30 MHz gain-bandwidth product, a 10 V/μs slew rate, rail-to-rail input and output operation, and typical input offset voltage below 150 μV. These specifications make it suitable for instrumentation, sensor interfaces, active filters, buffer stages, and industrial control circuits where DC accuracy and moderate-to-high bandwidth are both important.
Where to buy LT1630CS8 online?
Use the “Request a Quote” form on this page to request LT1630CS8 availability, lead time, and current commercial terms from XAIPART. The part is listed as production by Analog Devices, with distributor listings available for the 8-pin SOIC device and its ordering variants. Supply the required quantity, package preference, and target date so the quote can reflect the appropriate manufacturing and logistics conditions.
What is the price of LT1630CS8?
Use the “Request a Quote” form on this page for the current LT1630CS8 quotation, including the requested quantity and delivery requirements. The manufacturer product page lists a starting list reference for the LT1630 family, but market pricing can vary with the exact ordering suffix, quantity, and date. The structured offer shown on this page should be used only when a current quantity-break listing is available.
What is the lead time for LT1630CS8?
Request the current lead time and minimum order quantity through the “Request a Quote” form on this page. Analog Devices lists the LT1630 family in production, which supports ongoing sourcing, but actual lead time depends on the exact ordering suffix, order quantity, package format, current factory scheduling, and required delivery date. The request should identify those factors so the commercial response reflects the intended build.
Is LT1630CS8 in stock?
Stock availability for LT1630CS8 changes with order quantity and exact ordering code. Use the “Request a Quote” form on this page to request a current availability confirmation, including the desired quantity and any tape-and-reel or other packaging requirement. The Analog Devices product page identifies the LT1630 family as production, but production status alone does not guarantee immediate allocation for every package and quantity.

بيانات مرجعية هندسية لـ LT1630CS8 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LT1630CS8 when the design needs two independent precision amplifier channels, a 30 MHz gain-bandwidth product, a 10 V/μs slew rate, and rail-to-rail input and output behavior in an 8-pin SOIC package. It is particularly appropriate for instrumentation, sensor interfaces, active filters, and industrial signal-conditioning stages where the fast response remains useful. Select LT1630CN8 only after confirming that its ordering-grade and temperature characteristics satisfy the installation and after checking the manufacturer’s ordering information. Consider LM7332MA when its complete electrical specification is a better fit, but do not treat the cross-reference listing as proof of drop-in equivalence. In either case, verify supply range, offset voltage, output swing, stability, and every pin function before PCB release.

المقارنة مع البدائل

المعامل هذا المنتج LT1630CN8 LM7332MA
Brand Analog Devices Analog Devices Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOP

أبرز الفروقات

  • Dual precision channels in one package (مقابلLM7332MA)
  • Documented low-offset precision performance (مقابلLM7332MA)
  • Rail-to-rail input and output operation (مقابلLT1630CN8)

ملاحظات التصميم

Keep the inverting input, feedback resistor, and optional compensation capacitor in a compact loop because the LT1630CS8 has a 30 MHz gain-bandwidth product. Route the non-inverting input away from switching nodes and high-current return paths. Place supply bypass capacitors close to pins 4 and 8, with a short ground return, and avoid adding test pads or long breakout leads to sensitive input nodes.

Do not treat the rail-to-rail description as permission to exceed the electrical limits. Input and output voltages must remain within the limits specified for the actual supply voltage and temperature grade, and output current must remain below the amplifier’s capability. The unused channel must also receive a defined configuration. Review the LT1630 electrical-characteristics tables before selecting resistor values, loading, or supply tolerances.

At high closed-loop bandwidth, excessive capacitive loading can produce peaking, ringing, or instability. Keep output loads and probe capacitance reasonable, place any isolation or output-filter components close to the amplifier, and validate the assembled board with a scope. Account for probe and fixture capacitance when evaluating very high gain or narrow-band filter configurations, since board parasitics can materially alter the intended response.

Choose the supply rails from the LT1630 operating requirements rather than merely matching the signal range. Rail-to-rail input and output behavior does not guarantee operation at zero volts, and the available output swing and current depend on supply voltage and load. Use separate local bypass capacitance for each supply rail and check the power-consumption change when the two amplifier channels are active versus inactive.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance attributes require confirmation from the current Analog Devices product documentation for the exact ordering code.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

lt1630cs8 pbf LT1630CS8 datasheet LT1630CS8 datasheet pdf LT1630CS8 pinout LT1630CS8 specifications LT1630CS8 equivalent LT1630CS8 replacement LT1630CS8 cross reference LT1630CS8 vs LT1630CN8 LT1630CS8 price LT1630CS8 stock Analog Devices LT1630CS8

المكونات والمصطلحات ذات الصلة

Analog Devices LT1630CS8 LT1630CN8 LM7332MA LT1630 LT1631 precision operational amplifier dual amplifier rail-to-rail input rail-to-rail output gain-bandwidth product slew rate input offset voltage signal conditioning active filter bridge sensor interface industrial process control audio preamplifier SOIC-8 QFN family surface-mount package power management IC semiconductor
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر