LT1638HS8 - Dual 1.2MHz Micropower RRIO Op Amp | Analog Devices
MPN: LT1638HS8 ✓ نشطLT1638HS8 نظرة عامة
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The rail-to-rail input stage accepts input signals extending to the supply rails, while the rail-to-rail output stage can swing close to both rails. This capability places the LT1638HS8 within the broader operational amplifier hierarchy of signal-conditioning ICs used in instrumentation, sensor interfaces, filtering, and low-power control systems.
The LT1638 family is designed for low-power signal conditioning with a total supply voltage range of 2.5 V to 44 V. Each amplifier draws approximately 170 µA of quiescent current, supports input signals beyond the supply rails, and combines a 1.2 MHz gain-bandwidth product with a 0.4 V/µs slew rate. These characteristics make it useful for battery-powered measurement systems and low-voltage industrial equipment operating across widely separated supply rails.
Analog Devices specifies the LT1638HS8 as a standard general-purpose, dual-rail-to-rail-input-and-output amplifier in an 8-pin SO package. Its low quiescent current reduces the standing power required when both amplifier sections operate continuously. The 1.2 MHz bandwidth supports moderate-frequency gain and active filtering, while the 0.4 V/µs slew rate determines how quickly the output can follow moderate signal changes without requiring the drive capability of a high-speed amplifier.
Typical applications include low-power sensor conditioning, portable instrumentation, industrial control interfaces, battery-powered monitoring, and signal buffering. The LT1638HS8 is particularly appropriate when signals may approach the supply rails, the circuit must operate from a single supply, and the overall power budget restricts amplifier bias current. Its wide supply range also allows the same device architecture to serve low-voltage and higher-voltage industrial systems.
For a single-supply design, bypass each supply pin with a local decoupling capacitor and route the return current directly to the ground reference. The amplifier should be configured for stable closed-loop operation with a feedback network that defines the required gain. Because bandwidth and slew rate are finite, verify the intended signal amplitude and frequency rather than treating the 1.2 MHz gain-bandwidth figure as unlimited operating bandwidth.
This page combines the manufacturer product description, package and operating information, distributor records, and cross-reference results into an application-oriented component record. It also identifies unresolved electrical parameters and distinguishes exact lead-free order codes from alternatives that use a different package, so engineers can make a footprint-safe replacement decision.
بدائل مباشرة لـ LT1638HS8 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلLT1638HS8 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Rail-to-Rail Input | Rail-to-rail |
| Rail-to-Rail Output | Rail-to-rail |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.4 V/µs |
| Total Supply Voltage Range | 2.5 V to 44 V |
| Maximum Total Supply Voltage | 44 V |
| Quiescent Current per Amplifier | 170 µA |
| Input Bias Current | 0.25 µA |
| Common-Mode Rejection Ratio | 72 dB |
| نطاق درجة حرارة التشغيل | -40 °C to +125 °C |
| Input Over-The-Top Range | ±22 V |
| العلبة | 8-pin SOIC |
| Lead-Free Status | Lead-free package |
| نوع التركيب | Surface mount |
دليل تكوين أطراف LT1638HS8 8-pin soic
تكوين الأطراف لـ LT1638HS8 (حزمة 8-pin soic). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LT1638HS8.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LT1638HS8 مناسب لـ 6 التطبيقs: Low-Power Sensor Signal Conditioning, Portable Instrumentation, Industrial Control Interfaces, Battery-Powered Monitoring, Active Filtering and Signal Buffering, Field-Signal Interface Circuitry.
Low-Power Sensor Signal Conditioning
The LT1638HS8 fits low-power sensor front ends that amplify small differential signals while maintaining a strict current budget. Each amplifier draws approximately 170 µA of quiescent current and provides 1.2 MHz gain-bandwidth product, enough for many temperature, pressure, and position sensors operating at low or moderate signal frequencies. Rail-to-rail input and output behavior helps preserve signal headroom in single-supply systems, while the 72 dB CMRR specification provides useful rejection of common-mode disturbances. The design should still verify sensor output range, input offset, noise, and the required closed-loop gain against the specific transducer.
موصى به
Portable Instrumentation
The LT1638HS8 is appropriate for portable measurement equipment where every milliamp of circuit current affects battery life. Its approximately 170 µA quiescent current per amplifier and operation from a 2.5 V minimum total supply suit compact, battery-operated instruments. The 1.2 MHz gain-bandwidth product supports active filters and modest-frequency signal acquisition, while rail-to-rail output improves utilization of a low-voltage supply. For a practical implementation, keep sensor and amplifier grounds close together, decouple the supply locally, and confirm that the selected gain and filter bandwidth remain stable with the required source and load impedances.
موصى به
Industrial Control Interfaces
The LT1638HS8 can buffer low-level control and monitoring signals in industrial systems requiring broad supply flexibility. It operates from 2.5 V to 44 V and accepts over-the-top input signals extending to ±22 V, allowing it to interface with circuits using different voltage domains. Its 0.4 V/µs slew rate is suitable for moderate control signals rather than high-speed data. Designers should use input protection where transients are possible and verify the output swing under the actual load. The amplifier's micropower operation is especially useful in distributed monitoring nodes where standby and operating current must remain controlled.
موصى به
Battery-Powered Monitoring
The LT1638HS8 supports battery-powered monitoring circuits by combining low quiescent current with operation from a 2.5 V minimum total supply. Both amplifier sections can condition independent sensor channels, reducing the need for separate single amplifiers in compact designs. Rail-to-rail input and output stages help maximize usable signal range in low-voltage systems, while over-the-top input capability can simplify thresholding or event detection around the supply rails. The principal tradeoff is its 1.2 MHz bandwidth and 0.4 V/µs slew rate, so applications requiring fast transient capture should verify settling behavior or choose a higher-speed device.
موصى به
Active Filtering and Signal Buffering
The LT1638HS8 is useful for active filtering and buffering where moderate frequency content must be processed at low power. A 1.2 MHz gain-bandwidth product leaves bandwidth available for closed-loop gain, while rail-to-rail outputs improve signal swing in single-supply filters. The two independent channels support dual-stage filters, differential-to-single-ended conversion, or separate signal paths without requiring two packages. Component selection must account for noise, input offset, output loading, and filter stability. Because the available technical summary does not establish noise density or exact output-current limits, those values should be confirmed from the manufacturer electrical-characteristics table before finalizing a precision filter.
موصى به
Field-Signal Interface Circuitry
The LT1638HS8 fits field-signal interface circuits that must tolerate input levels beyond their local supply and retain low power consumption. Its input stage supports over-the-top operation to ±22 V, which is useful when monitoring, attenuating, or buffering external signals in systems with restricted supply voltage. The 72 dB CMRR rating helps suppress common-mode noise on field wiring, while the 2.5 V to 44 V supply range supports multiple installation classes. Engineers must add appropriate input attenuation and protection, verify that the maximum differential and common-mode conditions are safe, and check whether the 0.4 V/µs slew rate is sufficient for the intended waveform.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LT1638HS8 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Package | 8-pin SOIC |
| Brand | Analog Devices |
| Amplifier Channels | 2 channels |
| Input Type | Rail-to-rail |
| Output Type | Rail-to-rail |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.4 V/µs |
| Total Supply Voltage Range | 2.5 V to 44 V |
| Quiescent Current per Amplifier | 170 µA |
| Common-Mode Rejection Ratio | 72 dB |
| Operating Temperature Range | -40 °C to +125 °C |
| Input Over-The-Top Range | ±22 V |
أبرز الفروقات
- Wide operating supply combined with micropower consumption (مقابلTypical higher-bandwidth general-purpose dual amplifiers)
- Rail-to-rail input and output operation (مقابلConventional amplifiers requiring headroom around the supply rails)
- Dual amplifier in a standard 8-pin SOIC (مقابلSingle-channel amplifier implementations)
ملاحظات التصميم
Place the supply bypass capacitor as close as practical to the LT1638HS8 supply pin, with a short return path to the ground reference. Keep feedback resistors and sensitive input traces away from noisy switching paths. Because the device supports over-the-top inputs extending to ±22 V, distinguish the maximum input condition of the selected operating state from the absolute maximum rating and add clamping or series resistance when external wiring is exposed to transients.
Use the 1.2 MHz gain-bandwidth product as a closed-loop design constraint rather than an unconditional operating-frequency limit. At a closed-loop gain of 10, for example, the available signal bandwidth is approximately 120 kHz before other pole and phase-margin effects are considered. The 0.4 V/µs slew rate also limits full-power bandwidth for larger output swings. Simulate the intended filter or feedback network with realistic source and load impedances to confirm stability.
Estimated: each amplifier contributes approximately 170 µA of quiescent current at the specified operating conditions. With two amplifiers active, the base quiescent contribution is approximately 340 µA before output-current load, resistor bias current, and external circuit consumption are added. This calculation is an engineering estimate based on the documented per-amplifier value; use it to assess battery life and include the complete circuit load when sizing the power source.
Do not treat LT1638HS8, LT1638HS8#PBF, and LT1638HS8#TR as three different electrical amplifiers. They represent the base device, lead-free ordering designation, and tape-and-reel production format. Conversely, LT1638CMS8 uses a smaller MSOP package and cannot replace the 8-pin SOIC target without a PCB change. Confirm the package drawing, pin assignments, grade, temperature range, and complete order suffix before approving a substitution.
معلومات الامتثال
The distributor specification identifies LT1638HS8 as a lead-free package. No explicit RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification statement was established, so those fields remain unknown or not applicable.