Analog Devices

MAX3488AEGSA+ - 20Mbps RS-422/RS-485 Transceiver | Analog Devices

MPN: MAX3488AEGSA+ ✓ نشط
3.3V powered Vdss 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

MAX3488AEGSA+ نظرة عامة

The Analog Devices MAX3488AEGSA+ is a 3.3V-powered RS-422/RS-485 transceiver with one driver and one receiver, supporting data rates up to 20Mbps and ESD protection up to ±20kV. It is packaged in an 8-pin SOIC and is designed for industrial, instrumentation, and communications links requiring a compact, slew-rate-limited interface.

An RS-485 transceiver converts a differential digital signal between a logic-level UART or controller and a balanced, noise-resistant cable. RS-422 is also differential, but it generally supports point-to-point or limited multi-drop topologies. The MAX3488AEGSA+ combines these functions in the interface IC category, placing physical-layer signaling between embedded logic and external cabling. Its low-power 3.3V operation also makes it suitable for modern portable and distributed systems.

Key features include 20Mbps maximum data rate, ±20kV ESD protection, slew-rate-limited driver operation, and operation from a 3.3V supply. The slew-rate limitation reduces high-frequency EMI and helps limit reflections on longer cables, while ESD protection improves robustness when cables are connected or disconnected in industrial environments. The device provides one transmit driver and one receive receiver for compact point-to-point or multi-drop bus designs.

The MAX3488A family uses differential signaling to reject common-mode noise and improve signal integrity over longer cable runs. Because the MAX3488AEGSA+ is slew-rate limited, engineers should select termination and biasing networks that match the cable length and topology. The 8-pin SOIC format simplifies assembly in designs that require a small, standard surface-mount footprint.

Typical applications include industrial sensor networks, building automation equipment, robotics, process-control systems, remote I/O modules, and data acquisition equipment. The MAX3488AEGSA+ can also be used in point-to-point RS-422 links when both ends support the appropriate differential termination. In each case, the transceiver provides the physical layer while an external UART or microcontroller handles framing, addressing, and protocol functions.

Designers should verify the supply voltage, driver enable polarity, receiver enable polarity, grounding, and termination requirements against the manufacturer datasheet. A common ground reference is important for reliable operation, while bias resistors should be placed so the bus remains in an idle state when no driver is enabled. Cable routing should preserve differential symmetry and minimize stubs.

This product page combines the exact manufacturer and distributor specifications with practical interface-design guidance, package information, comparison data, and application-oriented design notes for engineers selecting or replacing an RS-422/RS-485 transceiver.

بدائل مباشرة لـ MAX3488AEGSA+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

SN75HVD12DR

✅ بديل مباشر
📦 SOIC-8
Cross-brand 8-pin SOIC RS-422/RS-485 transceiver; data rate, ESD rating, supply behavior, and enable functions require comparison against the MAX3488AEGSA+ before replacement.

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX3488AEGSA+ المواصفات

Product Type RS-422/RS-485 transceiver
Driver and Receiver Count 1 driver and 1 receiver
جهد التغذية 3.3V powered
Maximum Data Rate 20Mbps
ESD Protection ±20kV
Driver Slew Rate Slew-rate limited
العلبة 8-pin SOIC
نوع الواجهة RS-422 and RS-485
Signal Type Differential
Applications Extended cable runs and noisy environments
نوع التركيب Surface mount

دليل تكوين أطراف MAX3488AEGSA+ 8-pin soic

تكوين الأطراف لـ MAX3488AEGSA+ (حزمة 8-pin soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 8-pin soic لـ MAX3488AEGSA+

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3488AEGSA+.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MAX3488AEGSA+ مناسب لـ 6 التطبيقs: Industrial Sensor Networks, Building Automation Equipment, Robotics and Motor-Control Systems, Remote I/O Modules, Data-Acquisition Equipment, Point-to-Point RS-422 Links.

🏭

Industrial Sensor Networks

The MAX3488AEGSA+ fits distributed sensor networks that use RS-485 for longer-distance, noise-resistant communication. Its differential signaling helps reject common-mode interference, while the 3.3V supply supports compact controller boards and modern sensor nodes. The slew-rate-limited driver can reduce EMI and cable reflections, although the bus still requires correct termination, fail-safe biasing, grounding, and topology planning. Engineers should use the manufacturer’s interface guidance to verify enable timing and cable-length limits before deploying the link in a high-interference environment.

🏭

Building Automation Equipment

The MAX3488AEGSA+ is appropriate for building automation controllers, room modules, and HVAC interfaces that exchange data over a wired differential bus. The 8-pin SOIC package keeps the interface compact, and 20Mbps capability provides substantial headroom for local telemetry and configuration traffic. Its ±20kV ESD protection improves connector-adjacent robustness, but installation cables may also experience larger surges, so designers should add the appropriate protection network and follow a single-ended reference-ground strategy.

🏭

Robotics and Motor-Control Systems

The MAX3488AEGSA+ can carry commands and sensor data between a robot controller and distributed modules where cable runs create electrical noise and potential ground differences. Differential RS-485 communication is useful for reducing sensitivity to common-mode voltage, while slew-rate limiting helps control edge energy on the bus. For motor systems, separate the transceiver from switching nodes, maintain a stable reference ground, and consider isolation when ground offsets or surge exposure could exceed the operating conditions of the device.

🧩

Remote I/O Modules

The MAX3488AEGSA+ is well matched to remote I/O modules that use an embedded controller or UART to reach sensors, actuators, and field devices over a multi-drop RS-485 bus. The 3.3V operating supply, one-driver/one-receiver arrangement, and 8-pin SOIC footprint support compact interface sections. Its 20Mbps maximum rate gives design headroom, but field reliability depends on correct idle-state biasing, termination placement, common-mode analysis, and careful routing of the differential pair from the transceiver to the connector.

📺

Data-Acquisition Equipment

The MAX3488AEGSA+ supports laboratory and industrial data-acquisition systems that need a compact physical layer between a controller and remote measurement equipment. Differential signaling improves noise immunity over longer cable runs, and the MAX3488A family is specifically positioned for true RS-422/RS-485 communication. The 20Mbps rating allows high-speed transfers, but the selected cable length, connectors, shielding, grounding, and termination must be validated together because peak data rate alone does not guarantee reliable communication at every distance.

🌐

Point-to-Point RS-422 Links

The MAX3488AEGSA+ can be used for point-to-point RS-422 links between two systems that exchange differential data over a cable. RS-422 is commonly selected where a dedicated link is preferred over a multi-drop bus, and the transceiver’s up-to-20Mbps performance supports fast command or measurement traffic. Confirm the exact receiver and driver behavior, supply limits, and timing in the manufacturer datasheet, then use matched termination at the cable ends and preserve differential routing to minimize reflections.

ملخص المنتجات الموصى بها

SN75HVD12DR Cross-brand RS-422/RS-485 transceiver comparison يُستخدم في: Industrial Sensor Networks, Building Automation Equipment, Robotics and Motor-Control Systems, Remote I/O Modules, Data-Acquisition Equipment, Point-to-Point RS-422 Links
What is the MAX3488AEGSA+?
The MAX3488AEGSA+ is a 3.3V-powered RS-422/RS-485 transceiver from Analog Devices with one driver and one receiver. According to the manufacturer product information, it supports data rates up to 20Mbps and includes ±20kV ESD protection. The device is intended for differential communications over cables in industrial and other electrically noisy environments, with one integrated transceiver per 8-pin SOIC package.
What are the key specifications of MAX3488AEGSA+?
The MAX3488AEGSA+ combines a 3.3V supply, RS-422/RS-485 operation, one driver, one receiver, a maximum data rate of 20Mbps, and ±20kV ESD protection in an 8-pin SOIC package. Its slew-rate-limited driver helps reduce EMI and cable reflections. These specifications make the device suitable for long cable runs, industrial equipment, remote I/O, and data-acquisition systems.
Where can I download the MAX3488AEGSA+ datasheet PDF?
The MAX3488AEGSA+ datasheet and product information are available from Analog Devices on the MAX3488 product page. The page identifies the MAX3488 as a 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver and provides the relevant family documentation. Use the manufacturer page as the authoritative source for pin descriptions, electrical limits, timing, and application guidance.
Where can I find the MAX3488AEGSA+ pinout?
The MAX3488AEGSA+ uses an 8-pin SOIC package. The manufacturer datasheet and product-page documentation should be used when assigning the driver, receiver, enable, ground, and supply connections. Keep the pin-description table with the datasheet during PCB layout because the exact pin names and enable functions must be confirmed against the exact MAX3488A device ordering code.
How fast can the MAX3488AEGSA+ transmit data?
The MAX3488AEGSA+ supports data rates up to 20Mbps. This performance makes it suitable for demanding differential communication links, including industrial equipment, remote I/O, and data-acquisition systems. Actual usable rate depends on cable length, topology, termination, transceiver enable timing, and signal integrity, so those conditions should be evaluated together with the 20Mbps maximum rating.
What is the difference between RS-422 and RS-485 in the MAX3488AEGSA+?
RS-422 and RS-485 are both differential physical-layer standards, but RS-485 is generally intended for multi-drop buses while RS-422 is commonly used for point-to-point links and limited driver configurations. The MAX3488AEGSA+ can support both signaling environments. The correct topology, termination, idle bias, grounding, and driver-enable strategy depend on the cable and system architecture.
Does the MAX3488AEGSA+ include ESD protection?
The MAX3488AEGSA+ includes ±20kV ESD protection. This protection strengthens the interface against electrostatic discharge encountered during cable connection, field maintenance, or installation in industrial environments. It does not remove the need for correct grounding, cable handling, or system-level surge protection when the transceiver is exposed to larger transients than its specified ESD condition.
Why does the MAX3488AEGSA+ use a slew-rate-limited driver?
The slew-rate-limited driver in the MAX3488AEGSA+ reduces the speed of differential edge transitions. This helps limit high-frequency EMI and reduce reflections caused by improperly terminated cables. The trade-off is that edge shaping must be considered when selecting cable length, termination values, and the target data rate, especially when operating near the 20Mbps maximum.
Can the MAX3488AEGSA+ replace an RS-485 transceiver in a new design?
The MAX3488AEGSA+ can serve as an RS-485 transceiver in a new design when its 3.3V supply, 20Mbps data-rate capability, 8-pin SOIC footprint, driver and receiver arrangement, enable functions, and protection requirements match the system. For a direct PCB replacement, verify pin compatibility, voltage levels, termination behavior, and transceiver enable polarity against the existing device before releasing production hardware.
What is the best cross-brand equivalent for MAX3488AEGSA+?
The SN75HVD12DR is identified in the comparison information as a candidate equivalent to the MAX3488AEGSA+. Both are 8-pin SOIC RS-485/RS-422 transceivers, but engineers should verify supply range, maximum data rate, ESD rating, receiver topology, driver enable polarity, and shutdown behavior against the manufacturer datasheets before treating it as a drop-in replacement. Use XAIPART's Request a Quote form for sourcing and compatibility review.
When should I choose the MAX3488AEGSA+ over the SN75HVD12DR?
Choose the MAX3488AEGSA+ when its verified 3.3V operation, 20Mbps maximum data rate, ±20kV ESD protection, slew-rate-limited driver, and one-driver/one-receiver arrangement fit the design. Choose the SN75HVD12DR only after checking its manufacturer specifications and pin functions against the existing board. The final decision should prioritize confirmed electrical behavior and footprint compatibility rather than the transceiver family name.
Is MAX3488AEGSA+ suitable for industrial sensor networks?
The MAX3488AEGSA+ is suitable for industrial sensor networks when the bus is designed around differential RS-485 communication. Its 3.3V supply, up-to-20Mbps capability, ±20kV ESD protection, and slew-rate-limited driver support robust links in noisy environments. The PCB still needs proper termination, fail-safe biasing, grounding, surge protection, and cable-routing discipline to achieve reliable field performance.
What is the lifecycle status of MAX3488AEGSA+?
The MAX3488AEGSA+ is listed as a production part by Analog Devices, and the manufacturer product page provides current product information and documentation. The page identifies the MAX3488 family as a production transceiver product. For current lifecycle confirmation, request an updated quotation through XAIPART's Request a Quote form and provide the required quantity, package, and delivery information.
Is MAX3488AEGSA+ RoHS and REACH compliant?
RoHS and REACH status for the MAX3488AEGSA+ are not stated in the product-page information used for this listing. Compliance should therefore be confirmed from the current manufacturer declaration, material or environmental compliance documentation, or the exact product-entry records before a regulated design is released. Do not infer compliance from the package type, manufacturer, or distributor listing alone.
How should the MAX3488AEGSA+ be laid out on a PCB?
Place the MAX3488AEGSA+ so the differential driver and receiver connections have short, symmetric paths to the connector or transceiver network. Keep the ground and supply-return paths continuous, place decoupling capacitance close to the device, and route each differential pair as a tightly coupled pair with minimal stubs. External termination and fail-safe biasing should be positioned where they can be tested or adjusted without long unmatched traces.
What are the electrical limits for MAX3488AEGSA+?
The confirmed headline electrical limits are a 3.3V-powered interface, 20Mbps maximum data rate, and ±20kV ESD protection. The manufacturer datasheet is the source for exact supply-current limits, driver output voltage, receiver thresholds, propagation delay, input impedance, common-mode range, and absolute maximum ratings. Use those values for worst-case design calculations rather than estimating them from the product category.

بيانات مرجعية هندسية لـ MAX3488AEGSA+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MAX3488AEGSA+ when a 3.3V RS-422/RS-485 interface needs one driver, one receiver, operation up to 20Mbps, ±20kV ESD protection, and an 8-pin SOIC footprint. It is particularly suitable for compact industrial, remote I/O, automation, robotics, and data-acquisition interfaces where slew-rate control helps reduce cable-edge effects. Consider the SN75HVD12DR when its manufacturer specifications confirm equal or better supply behavior, data rate, ESD rating, enable logic, receiver topology, and timing while retaining the same SOIC footprint. For any direct replacement, verify every pin and every maximum and recommended operating condition rather than relying only on the family description. If the design requires stronger surge protection, galvanic isolation, or operation outside the confirmed electrical limits, choose a transceiver designed for those requirements or add the necessary protection network.

المقارنة مع البدائل

المعامل هذا المنتج SN75HVD12DR
Brand Analog Devices Texas Instruments
Package 8-pin SOIC 8-pin SOIC
Interface RS-422/RS-485 RS-485/RS-422
Signal Type Differential Differential
Primary Use Case Extended cable runs in noisy environments RS-485/RS-422 communications

أبرز الفروقات

  • High-speed differential interface capability (مقابلSN75HVD12DR)
  • Slew-rate-limited driver for controlled cable transitions (مقابلSN75HVD12DR)
  • Compact one-driver, one-receiver implementation (مقابلSN75HVD12DR)

ملاحظات التصميم

Route the differential pair as a tightly coupled pair from the transceiver to the connector, with minimal vias, stubs, and geometry changes. Keep the connector ground and transceiver ground return path continuous, and place termination components at the physical cable ends rather than near the controller. This minimizes reflections and helps preserve the differential signal relationship in noisy installations.

Do not connect multiple termination networks to every node on an RS-485 bus. Termination belongs at the two ends of the principal cable segment, while intermediate nodes should use the appropriate biasing network to hold the bus in a valid idle state. Confirm driver enable polarity and make sure only one transmitter is active during normal communication to avoid bus contention.

Treat the cable as part of the EMC design. The MAX3488AEGSA+ uses a slew-rate-limited driver, which helps reduce edge-related emissions, but the complete system still requires controlled board layout, suitable cable type, shielding when appropriate, and common-mode analysis. Keep high-current switching loops and motor-node wiring away from the differential pair, and verify radiated and conducted emissions at the product level.

Decouple the 3.3V supply locally and provide a low-impedance return from the transceiver ground to the connector and transceiver ground reference. Where the cable interface can experience ground potential differences or surge transients beyond the device’s specified limits, add suitable protection or isolation. Verify the exact supply current and operating limits from the manufacturer datasheet before sizing the regulator and bulk capacitance.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance status was not stated in the product information and must be confirmed against the exact MAX3488AEGSA+ manufacturer documentation.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MAX3488AEGSA+ datasheet MAX3488AEGSA+ pinout MAX3488AEGSA+ datasheet pdf MAX3488AEGSA+ equivalent MAX3488AEGSA+ replacement MAX3488AEGSA+ cross reference MAX3488AEGSA+ vs SN75HVD12DR MAX3488AEGSA+ 20Mbps transceiver MAX3488AEGSA+ 3.3V RS-485 MAX3488AEGSA+ SOIC-8 interface MAX3488AEGSA+ industrial sensor network Analog Devices MAX3488AEGSA+

المكونات والمصطلحات ذات الصلة

Analog Devices MAX3488AEGSA+ MAX3488A SN75HVD12DR Texas Instruments RS-422 RS-485 differential transceiver interface IC physical-layer signaling semi-duplex transceiver slew-rate-limited driver ESD protection 20Mbps data rate 3.3V power supply SOIC-8 surface mount industrial communication remote I/O data acquisition common-mode noise rejection differential signaling
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر