MPC8347ECVVAJDB - 533MHz PowerQUICC II Pro SoC | NXP | TBGA-672
MPN: MPC8347ECVVAJDB ⚠ آخر فرصة للشراءMPC8347ECVVAJDB نظرة عامة
A PowerQUICC II Pro processor is a system-on-chip (SoC) integrating a Power Architecture CPU core with communications peripherals, belonging to the broader category of communications processors -> embedded microprocessors -> microcontrollers and MPUs -> integrated circuits. PowerQUICC II Pro extends the original PowerQUICC II line with improved DDR memory support, gigabit Ethernet, and integrated security acceleration, making it suitable for routers, switches, and secure access equipment.
Key differentiating features include 533 MHz core clock with 32-bit RISC architecture, dual 10/100/1000 Mbps Ethernet, dual PCI 2.3 controllers, USB 2.0 Hi-Speed host/device, DDR1/DDR2 memory controller up to 333 MHz, integrated security engine (SEC) for crypto acceleration, and operating voltages of 1.8V/2.5V/3.3V. The 672-pin TBGA package supports the high pin count needed for parallel DDR, dual PCI, and dual gigabit Ethernet interfaces simultaneously.
The architecture combines an e300 superscalar PowerPC core with a system interface and communications engine module (CEM). The CEM offloads networking tasks from the CPU via dedicated DMA engines and QUICC Engine technology, allowing the CPU to focus on control plane and application processing. The SEC block accelerates DES, 3DES, AES, SHA-1/MD5, and public-key algorithms.
Typical applications include industrial routers and gateways, network-attached storage (NAS), secure VPN concentrators, factory automation controllers, and line cards for access equipment. The extended -40C to +105C temperature range supports outdoor and industrial deployments.
When designing with this part, ensure the PCB supports 672-ball TBGA routing with microvia stack-up, and provide adequate bulk decoupling on the 1.8V, 2.5V, and 3.3V rails. Software development requires Freescale/NXP CodeWarrior or Linux BSP for the e300 core.
This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and integrate this PowerQUICC II Pro part into industrial networking designs.
بدائل مباشرة لـ MPC8347ECVVAJDB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MPC8347ECVVAJDB (نفس عامل الشكل والبصمة) — يختلف في Ethernet, Memory Controller, Operating Temperature, PCI Interface, Security Engine.
MPC8347EVVAJDB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MPC8347VVAGDB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MPC8347ECZQAGDB
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MPC8347CZUAJDB
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MPC8347ECVRAGDB
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MPC8343ECVVAJDB
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MPC8347ECVVAJDB الحدود القصوى والخصائص الكهربائية
| Architecture | Power Architecture e300 (32-bit RISC) |
| Core Frequency | 533 MHz |
| Family | PowerQUICC II Pro (MPC83xx) |
| Memory Controller | DDR1/DDR2 up to 333 MHz |
| Ethernet | Dual 10/100/1000 Mbps (Gigabit) |
| PCI | Dual PCI 2.3 |
| USB | USB 2.0 Hi-Speed host/device |
| Security Engine | SEC (DES/3DES/AES/SHA) |
| Process Technology | 0.13 um CMOS |
| جهد التغذية | 1.8 V / 2.5 V / 3.3 V |
| درجة حرارة التشغيل | -40 C to +105 C |
| العلبة | 672-pin TBGA |
| نوع التركيب | Surface Mount |
| Tray Packaging | Yes |
| AEC-Q100 | not_applicable (industrial/comms) |
دليل تكوين أطراف MPC8347ECVVAJDB 672-pin tbga
تكوين الأطراف لـ MPC8347ECVVAJDB (حزمة 672-pin tbga). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MPC8347ECVVAJDB.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MPC8347ECVVAJDB مناسب لـ 6 التطبيقs: Industrial Secure Router/Gateway, Network-Attached Storage (NAS) Controller, Factory Automation Controller (PLC Edge Node), DSLAM/Access Line Card, Secure VPN Concentrator / SSL Appliance, Industrial Printer / Imaging Controller.
Industrial Secure Router/Gateway
The MPC8347ECVVAJDB is well suited for industrial secure routers and VPN gateways where 533 MHz Power Architecture processing, dual Gigabit Ethernet, and hardware-accelerated cryptography are needed in a single SoC. The integrated SEC engine accelerates AES, 3DES, SHA-1 and RSA, providing wire-speed IPsec/SSL throughput that software-only implementations cannot match. With DDR1/DDR2 controller supporting up to 333 MHz and dual PCI for expansion (e.g. additional Ethernet or crypto cards), the chip delivers a complete router-on-chip design. The -40C to +105C temperature grade supports outdoor cabinets, factory floors, and substation deployments where commercial-grade silicon would fail.
موصى به
Network-Attached Storage (NAS) Controller
For entry-level NAS controllers, the MPC8347ECVVAJDB provides 533 MHz CPU performance, dual Gigabit Ethernet for LAN/WAN aggregation, USB 2.0 Hi-Speed for external drives, and PCI for SATA or RAID expansion cards. The dual PCI 2.3 controllers enable a typical 4-port SATA configuration via PCI-SATA bridge chips. DDR2 memory support up to 333 MHz delivers the bandwidth needed for streaming reads/writes across multiple clients. The integrated SEC engine offloads SMB signing and file encryption, freeing the CPU for file-system and network-protocol processing.
موصى به
Factory Automation Controller (PLC Edge Node)
Industrial PLC edge nodes and factory automation controllers benefit from the MPC8347ECVVAJDB's industrial -40C to +105C temperature grade and its mix of deterministic PCI, Ethernet, and USB interfaces for connecting sensors, HMIs, and motor controllers. The e300 core's deterministic interrupt latency supports real-time fieldbus protocols such as PROFINET, EtherCAT, or Modbus TCP via software stacks. The dual Gigabit Ethernet ports enable ring-topology industrial Ethernet with cable redundancy. The integrated SEC engine secures over-the-air firmware updates and authenticates remote operators.
موصى به
DSLAM/Access Line Card
For DSL access multiplexer (DSLAM) line cards and broadband access equipment, the MPC8347ECVVAJDB's dual Gigabit Ethernet uplinks and dual PCI expansion buses allow connection to multiple xDSL line-driver cards while maintaining a single management CPU per line card. The QUICC Engine compatible peripheral set provides DMA-driven serial interfaces for legacy TDM/ATM backhaul. DDR2 memory controller supports the packet buffering needed for QoS-aware traffic shaping. Hardware crypto acceleration secures PPPoE, IPsec, and management-plane encryption without taxing the main CPU.
موصى به
Secure VPN Concentrator / SSL Appliance
VPN concentrators and SSL inspection appliances leverage the MPC8347ECVVAJDB's integrated SEC engine to deliver wire-speed AES-256/SHA-256 throughput for IPsec and TLS tunnels, while the 533 MHz e300 core handles routing tables, RADIUS/TACACS+ AAA integration, and policy enforcement. The PCI bus accommodates daughter cards for additional crypto accelerators or 10G uplinks. The -40C to +105C temperature grade and dual Gigabit Ethernet ports allow deployment in hardened edge appliances. DDR2 bandwidth is sufficient for sustained full-duplex gigabit traffic with encryption enabled.
موصى به
Industrial Printer / Imaging Controller
High-speed industrial printers and imaging controllers use the MPC8347ECVVAJDB to drive print engines, scanner CCDs, and LCD operator panels from a single chip. The USB 2.0 Hi-Speed host connects to flash drives or Wi-Fi modules for direct print jobs; the dual Gigabit Ethernet ports support production-line networked printers. The PCI bus interfaces to specialty image-processing DSPs or FPGA-based raster image processors. Extended-temperature silicon ensures reliable operation near printing heaters and in unconditioned shop-floor cabinets.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MPC8347ECVVAJDB — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MPC8347EVVAJDB | MPC8347VVAGDB | MPC8347ECZQAGDB | MPC8343ECVVAJDB |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 672-pin TBGA | 672-pin TBGA - same | 672-pin TBGA - same | 672-pin TBGA - same | 672-pin TBGA - same |
| Core Frequency | 533 MHz | 533 MHz | 533 MHz | 533 MHz | 533 MHz |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | 0 C to +105 C | -40 C to +105 C | -40 C to +105 C |
| Security Engine (SEC) | Yes | Yes | Yes | Yes | No (MPC8343 lacks SEC) |
| DDR Memory Support | DDR1/DDR2 to 333 MHz | DDR1/DDR2 to 333 MHz | DDR1/DDR2 to 333 MHz | DDR1/DDR2 to 333 MHz | DDR1/DDR2 to 333 MHz |
| Gigabit Ethernet Ports | 2 | 2 | 2 | 2 | 2 |
| Lifecycle Status (Oct 2026) | Last-time-buy (EOL announced) | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy |
أبرز الفروقات
- Integrated SEC engine for wire-speed crypto (مقابلMPC8343ECVVAJDB)
- Extended industrial temperature grade (مقابلMPC8347VVAGDB)
- Higher 533 MHz core speed within family (مقابلMPC8347E lower-speed grades)
ملاحظات التصميم
The 672-pin TBGA package requires a multi-layer PCB with microvia (laser-drilled) stack-up. Standard 0.4 mm ball pitch requires at least a 4-6 layer board with 1 oz copper and a low-loss dielectric (e.g. FR-408HR or equivalent). All BGA escape routing must be verified with NXP's BGA Escape Routing Guidelines before tape-out. Use a via-in-pad or dog-bone fanout depending on PCB density. Decoupling: place 0.1 uF + 10 uF ceramic caps within 5 mm of every power pin per NXP hardware specification.
The MPC8347ECVVAJDB requires three independent voltage rails (1.8 V core, 2.5 V DDR termination, 3.3 V I/O). Power sequencing per NXP datasheet must follow core-before-I/O order to avoid latch-up. Use a supervisor IC such as TPS3823 to enforce POR and reset sequencing. Estimated peak current at 533 MHz is approximately 1.2 A on 1.8 V core. Provide at least 20% margin on each regulator's current rating.
The 672 TBGA package has a theta_JA in the range of 15-20 C/W on a properly designed 4-layer PCB (refer to datasheet). At full CPU + SEC load, internal dissipation can reach 4-5 W. Provide a thermal pad or copper pour connected to the BGA's center ground balls to dissipate heat. For sealed industrial enclosures, verify junction temperature stays below +105 C at worst-case ambient using the theta_JC and board-thermal data.
Common pitfalls: (1) Do not use non-ECC DDR2 memory in safety-critical applications - the ECC controller requires specific chip-select wiring; (2) The USB 2.0 port requires an external PHY (e.g. ISP1504 or NXP USB3300) - it is NOT a USB transceiver; (3) The dual PCI controllers share pins with the local bus, requiring strap configuration at reset; (4) The SEC engine requires proper DMA descriptor alignment - misaligned descriptors cause silent crypto failures.
معلومات الامتثال
RoHS/lead-free status not stated in the verified distributor snippets; NXP's MPC8347E family generally offers both lead and lead-free versions (suffix ZQA = lead-free). Customers should request the latest Material Composition Declarations from NXP.
