PIC16C72-10E/SS - 8-Bit 10MHz OTP MCU 3.5KB | Microchip
MPN: PIC16C72-10E/SS ⚠ آخر فرصة للشراءPIC16C72-10E/SS نظرة عامة
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripherals. Within the component taxonomy, the PIC16C72 sits in the 8-bit MCU tier of the broader microcontroller category, which itself belongs to the integrated circuit and embedded semiconductor hierarchy. OTP program memory means the device can be programmed exactly once and is intended for cost-sensitive production runs where field reprogrammability is not required. The RISC architecture executes 35 single-word instructions, with all instructions completing in one instruction cycle except program branches, which take two cycles.
Key features include 22 digital I/O lines, an integrated I2C/SPI peripheral interface, a Pulse-Width Modulation (PWM) module, a Watchdog Timer (WDT) for safe operation, Brown-out Detect/Reset, and Power-On Reset (POR). The integrated 8-bit ADC provides five input channels for direct sensor interfacing without an external converter, which simplifies BOM and board area. The PIC16C72 family is well documented in the official Microchip datasheet and supported by the standard PICmicro mid-range toolchain (MPLAB IDE, MPASM assembler, and ICD in-circuit debug).
Typical applications include automotive body and chassis controllers, small appliance control, sensor signal conditioning nodes, low-end consumer electronics, and industrial control modules. The 28-SSOP package offers a compact surface-mount footprint for space-constrained designs while retaining through-hole-style ease of hand-rework on the bench.
When designing with this device, note that OTP memory cannot be erased or reprogrammed; plan for code revision control and use a windowed (JW) or flash-based PIC16F72 for development and prototype runs. Power supply decoupling of 0.1 uF close to VDD and proper ground layout are required for reliable ADC operation.
This page synthesizes distributor pricing, drop-in same-package alternatives, and engineering design notes not aggregated on a single manufacturer or distributor page.
بدائل مباشرة لـ PIC16C72-10E/SS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PIC16C72-10E/SS (نفس عامل الشكل والبصمة) — يختلف في Core Architecture, Package, Operating Temperature, Timers, I/O Pins.
PIC16C72-10I/SS
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PIC16C72-10/SS
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16C72A-10E/SS
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PIC16F72-I/SS
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16F873A-I/SS
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16C72-10E/SS الحدود القصوى والخصائص الكهربائية
| Core Architecture | 8-bit PIC16C RISC |
| Program Memory Type | OTP (One-Time-Programmable) |
| Program Memory Size | 3.5 KB (2K x 14) |
| Data RAM | 128 x 8 bytes |
| أقصى تردد للساعة | 10 MHz |
| Instruction Cycle | 200 ns |
| I/O Pins | 22 |
| ADC | 8-bit, 5 channels |
| Communication Interfaces | I2C, SPI |
| PWM Channels | Yes (1 channel per datasheet) |
| Watchdog Timer | Yes (WDT) |
| Brown-out Reset | Yes (BOR) |
| Power-On Reset | Yes (POR) |
| درجة حرارة التشغيل | -40C to +125C (Extended, "E" grade) |
| العلبة | 28-SSOP (0.209", 5.30 mm width) |
| نوع التركيب | Surface Mount |
| عدد الأطراف | 28 |
| Instruction Set | 35 single-word instructions |
تكوين أطراف PIC16C72-10E/SS
| دبوس 1 | MCLR/VPP — Master Clear (Reset) input / programming voltage |
| دبوس 2 | RA0/AN0 — Digital I/O / Analog input channel 0 |
| دبوس 3 | RA1/AN1 — Digital I/O / Analog input channel 1 |
| دبوس 4 | RA2/AN2 — Digital I/O / Analog input channel 2 |
| دبوس 5 | RA3/AN3/VREF — Digital I/O / Analog input 3 / ADC voltage reference |
| دبوس 6 | RA4/T0CKI — Digital I/O / Timer 0 clock input |
| دبوس 7 | RA5/AN4/SS — Digital I/O / Analog input 4 / SPI slave select |
| دبوس 8 | VSS — Ground reference |
| دبوس 9 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| دبوس 10 | OSC2/CLKOUT — Crystal oscillator output / clock output |
| دبوس 11 | RC0/T1OSO/T1CKI — Digital I/O / Timer 1 oscillator output / Timer 1 clock input |
| دبوس 12 | RC1/T1OSI/CCP2 — Digital I/O / Timer 1 oscillator input / CCP2 PWM output |
| دبوس 13 | RC2/CCP1 — Digital I/O / CCP1 PWM output |
| دبوس 14 | RC3/SCK/SCL — Digital I/O / SPI clock / I2C clock |
| دبوس 15 | RC4/SDI/SDA — Digital I/O / SPI data in / I2C data |
| دبوس 16 | RC5/SDO — Digital I/O / SPI data out |
| دبوس 17 | RC6 — Digital I/O |
| دبوس 18 | RC7 — Digital I/O |
| دبوس 19 | VSS — Ground reference |
| دبوس 20 | VDD — Positive supply voltage |
| دبوس 21 | RB0/INT — Digital I/O / External interrupt input |
| دبوس 22 | RB1 — Digital I/O |
| دبوس 23 | RB2 — Digital I/O |
| دبوس 24 | RB3 — Digital I/O |
| دبوس 25 | RB4 — Digital I/O |
| دبوس 26 | RB5 — Digital I/O |
| دبوس 27 | RB6 — Digital I/O |
| دبوس 28 | RB7 — Digital I/O |
التطبيقات النموذجية
PIC16C72-10E/SS مناسب لـ 6 التطبيقs: Automotive Body and Chassis Controllers, Small Appliance Control, Industrial Sensor Signal Conditioning Nodes, Low-End Consumer Electronics, HVAC and Environmental Control Modules, Battery Charger and Power Management Controllers.
Automotive Body and Chassis Controllers
The PIC16C72-10E/SS's Extended -40C to +125C temperature grade and 22 digital I/O lines make it well-suited to under-hood and body-electronics modules such as lighting controllers, seat controllers, and accessory multiplexers. The integrated 5-channel 8-bit ADC reads analog sensor inputs (e.g., temperature, position, current shunt) directly, eliminating an external ADC and reducing BOM cost in OBD and HVAC subsystems. The 10 MHz core provides a 200 ns instruction cycle, which is sufficient for slow-loop control loops with millisecond-scale time constants typical in body ECUs.
موصى به
Small Appliance Control
White-goods and small kitchen appliances (coffee makers, microwaves, washing-machine user-interface boards) use the PIC16C72-10E/SS for its 3.5 KB OTP program memory, PWM module for motor or heater drive, and 22 I/O for keypad and display scanning. The 5-channel 8-bit ADC reads thermistor, weight, or water-level sensors directly. OTP memory suits high-volume appliance production where firmware is fixed and cost per unit dominates; the SSOP package allows compact main-control boards.
موصى به
Industrial Sensor Signal Conditioning Nodes
Distributed industrial sensor nodes benefit from the PIC16C72-10E/SS's 8-bit ADC, I2C/SPI interfaces, and robust SSOP packaging on conformal-coated boards. The MCU can read 4-20 mA loop or 0-10 V analog signals through the ADC, perform linearization and threshold detection, and forward results over I2C or SPI to a supervisory PLC or gateway. Operating temperature of -40C to +125C (E grade) supports outdoor panel and factory-floor enclosures.
موصى به
Low-End Consumer Electronics
Cost-sensitive consumer products (remote controls, toys, simple user interfaces, LED drivers) leverage the PIC16C72-10E/SS's low unit cost, OTP memory, and built-in PWM for brightness or motor-speed control. The 35-instruction RISC core is easy to program in assembly for ultra-low-MIPS tasks, and the 22 I/O lines accommodate keypads, IR receivers, and LED arrays. The 28-SSOP footprint fits thin consumer enclosures where every square millimeter counts.
موصى به
HVAC and Environmental Control Modules
Heating, ventilation, and air-conditioning control boards use the PIC16C72-10E/SS to read temperature/humidity sensors via the 8-bit ADC, drive triacs or relays through PWM or digital outputs, and communicate with room sensors over I2C. The 128-byte RAM and 3.5 KB OTP memory hold scheduling logic and lookup tables. The Extended temperature grade supports installations in attics, basements, and outdoor HVAC equipment exposed to wide thermal swings.
موصى به
Battery Charger and Power Management Controllers
Small-form-factor battery chargers and DC-DC supervisor modules use the PIC16C72-10E/SS's ADC to monitor battery voltage and current, the PWM channel to drive the charger MOSFET, and I2C/SPI to report state to a host. The Brown-out Detect and Power-On Reset functions provide safe startup and brownout protection without external components. The Extended temperature grade enables use in outdoor solar charge controllers and automotive battery maintainers.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PIC16C72-10E/SS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | PIC16C72-10I/SS | PIC16C72-10/SS | PIC16C72A-10E/SS | PIC16F72-I/SS | PIC16F873A-I/SS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB Flash | 7 KB Flash |
| Max Clock Frequency | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 20 MHz | 20 MHz |
| ADC | 8-bit, 5 ch | 8-bit, 5 ch | 8-bit, 5 ch | 8-bit, 5 ch | 8-bit, 5 ch | 10-bit, 5 ch |
| I/O Pins | 22 | 22 | 22 | 22 | 22 | 22 |
| Temperature Grade | -40C to +125C (Extended) | -40C to +85C (Industrial) | 0C to +70C (Standard) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Lifecycle Status | Last-Time-Buy | Last-Time-Buy | Last-Time-Buy | Active (newer) | Active (recommended) | Active |
أبرز الفروقات
- Extended automotive temperature grade in same 28-SSOP package (مقابلPIC16C72-10I/SS)
- Drop-in compatibility with flash-based PIC16F72-I/SS for development (مقابلPIC16F72-I/SS)
- Original silicon revision explicitly documented by Microchip (مقابلPIC16C72A-10E/SS)
ملاحظات التصميم
OTP memory on PIC16C72-10E/SS cannot be erased or rewritten. Engineers must verify firmware with a JW (windowed ceramic) or PIC16F72-I/SS flash sample before committing to OTP production parts. A single bit error in production firmware requires scrapping the part. Source: Microchip PIC16C72 datasheet memory architecture section.
Place a 0.1 uF decoupling capacitor as close as possible to the VDD pin (pin 20) with a short trace to the VSS pin (pin 19). For ADC accuracy, add a 10 uF bulk capacitor on VDD and an additional 0.1 uF near AVdd if used. Inadequate decoupling is the leading cause of ADC noise and erratic reset behavior on PIC16C7X designs.
Route the OSC1/OSC2 crystal traces short and symmetric, with the crystal and load capacitors (typically 15-33 pF) within 5 mm of the MCU. Keep clock traces away from high-current switching lines and ADC analog inputs to avoid coupling noise into ADC conversions. The 28-SSOP package requires thermal relief on pads for hand-rework.
The I2C/SPI pins (RC3/RC4 for I2C, RC3-RC5 for SPI) share functions with digital I/O; configure SSPEN properly before peripheral use. Use 4.7 kohm pull-ups on SCL and SDA for standard-mode I2C at 100 kHz. ADC analog inputs (RA0-RA5) should be buffered with an op-amp if source impedance exceeds 2.5 kohm to avoid conversion errors.
معلومات الامتثال
RoHS, REACH, and lead-free status not explicitly stated in the verified distributor listings for PIC16C72-10E/SS; marked as [DATA_NEEDED]. The E temperature grade indicates automotive qualification intent, but AEC-Q100 conformance is not_applicable for general-purpose MCU datasheets unless explicitly listed. Source: distributor pages (DigiKey, Heisener) do not surface compliance badges for this part.
