PIC16C74A-10/P - 8-Bit 10MHz OTP MCU 7KB 192 RAM | Microchip
MPN: PIC16C74A-10/P ✗ انتهى عمره الإنتاجيPIC16C74A-10/P نظرة عامة
An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, memory (ROM/RAM), and peripheral blocks on a single silicon die, executing instructions from a Harvard-architecture instruction set. The PIC16C7X family belongs to the mid-range PIC16CXX lineage of microcontrollers -> RISC microcontrollers -> embedded microcontrollers -> microprocessors -> semiconductors. These MCUs are widely used for industrial control, motor drive, instrumentation, and consumer product designs because of their deterministic instruction timing, low power consumption, and mature toolchain support.
Key features of the PIC16C74A-10/P include a 10 MHz maximum operating frequency (200 ns instruction execution), 8 channels of 8-bit analog-to-digital conversion, two capture/compare/PWM modules, a USART serial port, and a synchronous serial port (SSP) for SPI/I2C communication. The OTP program memory allows one-time factory or in-circuit programming, distinguishing this part from flash-based F-series PIC16 devices that permit in-field re-programming.
Architecturally, the PIC16C74A-10/P uses a RISC-based core with only 35 single-word instructions, simplifying software development while delivering deterministic throughput. The integrated analog comparator, watchdog timer, and brown-out reset circuit further reduce external component requirements in typical designs. Operating from 4V to 5.5V, the device is tailored for legacy 5V industrial systems.
Typical applications include industrial motor control, HVAC actuator interfaces, instrumentation front-ends, security system controllers, and consumer appliance control boards. The wide I/O count and analog integration suit designs that previously required separate logic and ADC chips.
When designing with this part, note that the OTP memory cannot be re-programmed; if in-field firmware updates are required, the user should evaluate PIC16F74 or PIC16F877A flash-based alternatives in the same 40-pin PDIP footprint.
This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C7X family, and practical design notes not found in the manufacturer datasheet alone.
بدائل مباشرة لـ PIC16C74A-10/P — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PIC16C74A-10/P (نفس عامل الشكل والبصمة) — يختلف في Package, Core Architecture, Timers, Operating Temperature, Program Memory Size.
PIC16C74A-10/L
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16C74A-04I/P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16C74B-20I/P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16F74-I/P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16F877A-I/P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC16C74A-10/P الحدود القصوى والخصائص الكهربائية
| Core Architecture | 8-bit PIC16CXX mid-range RISC |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 7 KB (4K x 14 words) |
| RAM | 192 bytes |
| Maximum CPU Frequency | 10 MHz |
| Instruction Execution Time | 200 ns (10 MHz, single cycle) |
| جهد التغذية | 4 V to 5.5 V |
| I/O Pins | 33 |
| ADC | 8-channel, 8-bit |
| PWM Modules | 2 (Capture/Compare/PWM) |
| USART | 1 (Addressable) |
| Synchronous Serial Port | Yes (SPI / I2C master) |
| Timers | 3 (Timer0, Timer1, Timer2) |
| Watchdog Timer | Yes (on-chip, software-enabled) |
| Brown-Out Reset | Yes |
| العلبة | 40-pin PDIP (P) |
| نوع التركيب | Through-Hole |
| درجة حرارة التشغيل | -40C to +85C (industrial) |
| حالة RoHS | Compliant |
تكوين أطراف PIC16C74A-10/P
| دبوس 1 | MCLR/VPP — Master Clear (Reset) input / Programming voltage |
| دبوس 2 | RA0/AN0 — PORTA bit 0 / Analog channel 0 |
| دبوس 3 | RA1/AN1 — PORTA bit 1 / Analog channel 1 |
| دبوس 4 | RA2/AN2 — PORTA bit 2 / Analog channel 2 |
| دبوس 5 | RA3/AN3/VREF+ — PORTA bit 3 / Analog channel 3 / ADC VREF+ |
| دبوس 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| دبوس 7 | RA5/AN4/SS — PORTA bit 5 / Analog channel 4 / SPI slave select |
| دبوس 8 | RE0/RD/AN5 — PORTE bit 0 / Read control / Analog channel 5 |
| دبوس 9 | RE1/WR/AN6 — PORTE bit 1 / Write control / Analog channel 6 |
| دبوس 10 | RE2/CS/AN7 — PORTE bit 2 / Chip select / Analog channel 7 |
| دبوس 11 | VDD — Positive supply (5V) |
| دبوس 12 | VSS — Ground reference |
| دبوس 13 | OSC1/CLKIN — Crystal oscillator input / external clock in |
| دبوس 14 | OSC2/CLKOUT — Crystal oscillator output / clock out |
| دبوس 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock in |
| دبوس 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| دبوس 17 | RC2/CCP1 — PORTC bit 2 / Capture Compare PWM1 |
| دبوس 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| دبوس 19 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| دبوس 20 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| دبوس 21 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| دبوس 22 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| دبوس 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| دبوس 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| دبوس 25 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| دبوس 26 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| دبوس 27 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| دبوس 28 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| دبوس 29 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| دبوس 30 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| دبوس 31 | VSS — Ground reference |
| دبوس 32 | VDD — Positive supply (5V) |
| دبوس 33 | RB0/INT — PORTB bit 0 / External interrupt |
| دبوس 34 | RB1 — PORTB bit 1 |
| دبوس 35 | RB2 — PORTB bit 2 |
| دبوس 36 | RB3/PGM — PORTB bit 3 / Low-voltage programming |
| دبوس 37 | RB4 — PORTB bit 4 |
| دبوس 38 | RB5 — PORTB bit 5 |
| دبوس 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| دبوس 40 | RB7/PGD — PORTB bit 7 / ICSP data |
التطبيقات النموذجية
PIC16C74A-10/P مناسب لـ 6 التطبيقs: Industrial Motor Control, HVAC Actuator Interface, Security System Controller, Instrumentation Front-End, Consumer Appliance Control, Automotive Aftermarket Modules.
Industrial Motor Control
The PIC16C74A-10/P is well suited to industrial motor control designs because its 8-channel 8-bit ADC and dual Capture/Compare/PWM modules drive H-bridge MOSFET stages directly from a 5V rail. At 10 MHz CPU clock (200 ns instruction cycle), the device executes the PI control loop fast enough to handle sub-millisecond torque updates for small DC and stepper motors. The 33 I/O pins allow direct interface to encoder inputs, limit switches, and fault indicators without external logic. According to the PIC16C7X datasheet, the PWM modules support up to 10-bit duty resolution, sufficient for variable-speed drives from 100 Hz to 25 kHz. Brown-out reset protects motor parameters in noisy 24V-bus derived 5V supplies typical of industrial cabinets.
موصى به
HVAC Actuator Interface
In HVAC actuator interfaces, the PIC16C74A-10/P reads thermistor or 4-20 mA sensor signals through its 8-channel ADC and drives damper/servo outputs via PWM. The wide 4V to 5.5V supply range accommodates 5V linear regulators fed from 24V HVAC rails. Built-in USART supports BACnet or Modbus slave communication over RS-485 transceivers. The 35-instruction RISC core is well documented and supported by Microchip's MPLAB assembler and HI-TECH C compiler, simplifying IEC 60730 safety-class firmware development. The 192-byte RAM is sufficient for PID state variables, sensor filtering, and protocol buffers in typical HVAC zone controller designs.
موصى به
Security System Controller
Security system panels benefit from the PIC16C74A-10/P's 33 I/O count, which accommodates multiple zone inputs (PIR, door contact, glass-break), keypad scanning, and siren/strobe output drivers without external mux ICs. The integrated synchronous serial port (SSP) supports SPI EEPROMs for event-log storage, while the USART drives a central-station modem or GSM module. The OTP memory ensures firmware cannot be tampered with by simple external reprogramming, an advantage for anti-tamper applications. Watchdog timer and brown-out reset protect against code runaway and supply glitches, both critical for UL-listed security installations requiring continuous fault monitoring.
موصى به
Instrumentation Front-End
Test and measurement front-ends use the PIC16C74A-10/P to digitize analog signals via its 8-channel ADC, drive character LCDs through parallel PORTD/PORTE pins, and stream readings over UART to a host PC. The 10 MHz instruction cycle supports >20 kHz ADC sampling for low-bandwidth vibration and strain-gauge measurement. On-chip comparators and capture modules enable frequency-to-count conversion for tachometer inputs. The 7 KB OTP program memory accommodates calibration tables and linearization routines needed in sensor signal conditioning paths. RoHS-compliant PDIP packaging allows hand-soldered prototype construction common in lab instrumentation.
موصى به
Consumer Appliance Control
Washing machines, dishwashers, and small kitchen equipment leverage the PIC16C74A-10/P's integrated peripherals to replace discrete logic: timers drive motor phases, ADC monitors water level/temperature, PWM modulates heater elements, and I/O reads button matrix and rotary encoders. The 5V supply rail simplifies power supply design using low-cost linear regulators from rectified mains. The 33 I/O count accommodates all user-interface and load-control wiring in a single chip, reducing BOM cost. Microchip's mature MPLAB toolchain and reference designs shorten consumer appliance time-to-production, while OTP memory prevents unauthorized cloning of firmware in cost-sensitive high-volume products.
موصى به
Automotive Aftermarket Modules
Aftermarket automotive modules such as gauge clusters, alarm systems, and auxiliary lighting drivers use the PIC16C74A-10/P at its 4V to 5.5V supply range, which is compatible with 12V vehicle electrical systems after regulation. The 8-channel ADC reads multiple sensor inputs (temperature, voltage, switch positions) while the PWM modules drive LED dimmers and motor actuators. The 33 I/O count supports matrix keypads and RGB indicator rings without external expanders. Operating temperature of -40C to +85C covers under-dash and engine-bay-adjacent installations. Brown-out reset and watchdog timer ensure reliable operation across automotive cranking transients typical of 12V lead-acid battery systems.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PIC16C74A-10/P — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | PIC16C74A-10/L | PIC16C74B-20I/P | PIC16F74-I/P | PIC16F877A-I/P |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin PDIP | 40-pin CERDIP (windowed) | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same |
| Program Memory Type | OTP (7 KB) | Windowed EPROM (7 KB, prototype use) | OTP (7 KB) | Flash (7 KB) | Flash (14 KB) |
| Maximum CPU Frequency | 10 MHz | 10 MHz | 20 MHz | 20 MHz | 20 MHz |
| RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 368 bytes |
| ADC | 8-channel, 8-bit | 8-channel, 8-bit | 8-channel, 8-bit | 8-channel, 8-bit | 8-channel, 10-bit |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| Supply Voltage | 4 V to 5.5 V | 4 V to 5.5 V | 4 V to 5.5 V | 4 V to 5.5 V | 4 V to 5.5 V |
| Lifecycle Status | NRND | NRND | Production (legacy) | Active (recommended replacement) | Active |
أبرز الفروقات
- Higher CPU performance (مقابلPIC16C74A-04I/P)
- Re-programmable flash memory (مقابلPIC16F74-I/P)
- More program memory and RAM (مقابلPIC16F877A-I/P)
ملاحظات التصميم
Decouple both VDD pins (pin 11 and pin 32) with 100 nF ceramic capacitors placed within 5 mm of each pin, plus a single 10 uF bulk electrolytic near the package. The PIC16C74A-10/P draws up to 25 mA active at 10 MHz and 5 V; ensure the regulator provides 50% headroom for transient spikes. Tie MCLR/VPP (pin 1) high through a 10 kohm resistor and add a 100 nF cap to ground for noise immunity, per Microchip PIC16C7X datasheet section on reset circuitry. Do not power the MCU through long wire harnesses without local bulk capacitance.
Route the crystal traces (OSC1/OSC2, pins 13-14) as short as possible and keep them away from PORTC switching lines to avoid coupling noise into the system clock. Use a guarded ground ring around the crystal can to reduce EMI. For through-hole PDIP prototypes, place a ground plane on the opposite PCB side to give the MCU a low-impedance return path; this also helps dissipate the small amount of heat (~125 mW at full speed). Avoid running high-current traces under the IC to prevent ground-bounce during switching events.
Do not assume code compiled for PIC16F74 will run on PIC16C74A without checking oscillator configuration bits and watchdog enable state - the C-variant uses different CONFIG word addresses. When designing with the OTP variant, ensure firmware is fully validated on a windowed PIC16C74A-10/L before committing to OTP programming, because OTP cannot be erased. Brown-out reset must be enabled in the configuration word for reliable 5V industrial operation; leaving BOR disabled risks corrupted EEPROM variables during power dips.
معلومات الامتثال
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - this is a commercial/industrial grade MCU. Choose PIC16F77 automotive-grade variants for AEC-Q100 requirements.
