PIC24HJ128GP506A-I/MR - 16-bit 40MIPS 128KB Flash MCU | Microchip 64-VQFN
MPN: PIC24HJ128GP506A-I/MR ✓ نشطPIC24HJ128GP506A-I/MR نظرة عامة
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (typically Flash), working RAM, and a rich set of peripherals such as ADC, PWM, UART, SPI and I2C. Within the semiconductor hierarchy, the PIC24HJ128GP506A belongs to the 16-bit MCU class -> microcontroller family -> embedded processor category -> semiconductor IC. The "PIC24H" sub-family is Microchip's high-performance 16-bit tier, sitting above the cost-optimized PIC24F and below the dsPIC33F DSP-enhanced parts, making it well suited to closed-loop control loops, motor drive, and high-speed sensor interfacing.
Key features include a 16-channel 12-bit ADC capable of 500 ksps conversion, up to eight PWM outputs with edge-aligned or center-aligned modes, two UART, two SPI and two I2C peripherals, and a 16-bit timer/counter bank. The device also exposes multiple DMA channels that offload data movement between peripherals and RAM, freeing CPU cycles for application logic. The wide 3.0V to 3.6V supply range, dual Watchdog Timer and Fail-Safe Clock Monitor support robust industrial deployments. The ICSP/In-Circuit programming interface enables in-field firmware updates without removing the device from the PCB.
Typical applications include industrial motor control (BLDC/PMSM FOC), digital signal processing front-ends, multi-channel data acquisition, point-of-load system monitoring, and embedded control for medical and consumer appliances. The 64-VQFN package exposes up to 53 digital I/O pins, supporting parallel sensor buses and human-interface buttons/LEDs simultaneously. Pair the MCU with an external EEPROM or serial Flash for data logging, and use the integrated 12-bit ADC for transducer readout.
When laying out the PCB, place the 64-VQFN exposed pad (EP) directly over a top-layer copper pour stitched with thermal vias to inner ground layers to keep junction temperature within the -40C to +85C industrial range. The PIC24HJ128GP506A-I/MR is pin-compatible with the PIC24HJ128GP306A-I/MR and PIC24HJ128GP306-I/MR variants, simplifying PCB reuse across the 128/64 KB Flash tiers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
بدائل مباشرة لـ PIC24HJ128GP506A-I/MR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PIC24HJ128GP506A-I/MR (نفس عامل الشكل والبصمة) — يختلف في Package, ADC, Operating Temperature, Timers, Program Memory (Flash).
PIC24HJ128GP306A-I/MR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC24HJ128GP306A-I/MR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC24HJ128GP306-I/MR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PIC24HJ128GP306A-E/MR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←dsPIC33FJ128GP306A-I/MR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PIC24HJ128GP506A-I/MR الحدود القصوى والخصائص الكهربائية
| Core Architecture | PIC24H (16-bit RISC, modified Harvard) |
| Maximum CPU Speed | 40 MIPS (80 MHz FOSC/2) |
| Program Memory (Flash) | 128 KB (43K x 24) |
| Data RAM | 8 KB |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| ADC | 12-bit, up to 16 channels, 500 ksps |
| Digital I/O Pins | Up to 53 |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | Up to 2 |
| PWM Outputs | Up to 8 (16-bit) |
| DMA Channels | Yes (8 channels) |
| Timers | 16-bit Timer/Counter (multiple) |
| Watchdog Timer | Yes (WDT, Fail-Safe Clock Monitor) |
| درجة حرارة التشغيل | -40C to +85C (Industrial, "-I") |
| العلبة | 64-pin VQFN (9x9 mm) - "MR" suffix |
| نوع التركيب | Surface Mount |
| مستوى MSL | MSL3 (per JEDEC J-STD-020, reflow 260C) |
| Programming Interface | ICSP / ICD (PGECx/PGEDx) |
| حالة RoHS | Compliant |
تكوين أطراف PIC24HJ128GP506A-I/MR
| دبوس 1 | RP15/CN15/PMD15/RB15 — Remappable I/O, CN15, PMP data bit 15, I/O port B15 |
| دبوس 2 | RP14/CN14/PMD14/RB14 — Remappable I/O, CN14, PMP data bit 14, I/O port B14 |
| دبوس 3 | RP13/CN13/PMD13/RB13 — Remappable I/O, CN13, PMP data bit 13, I/O port B13 |
| دبوس 4 | RP12/CN12/PMD12/RB12 — Remappable I/O, CN12, PMP data bit 12, I/O port B12 |
| دبوس 5 | RP11/CN11/PMD11/RB11 — Remappable I/O, CN11, PMP data bit 11, I/O port B11 |
| دبوس 6 | RP10/CN10/PMD10/RB10 — Remappable I/O, CN10, PMP data bit 10, I/O port B10 |
| دبوس 7 | RP9/CN9/PMD9/RB9 — Remappable I/O, CN9, PMP data bit 9, I/O port B9 |
| دبوس 8 | RP8/CN8/PMD8/RB8 — Remappable I/O, CN8, PMP data bit 8, I/O port B8 |
| دبوس 9 | RP7/CN7/PMD7/RB7 — Remappable I/O, CN7, PMP data bit 7, I/O port B7 |
| دبوس 10 | RP6/CN6/PMD6/RB6 — Remappable I/O, CN6, PMP data bit 6, I/O port B6 |
| دبوس 11 | RP5/CN5/PMD5/RB5 — Remappable I/O, CN5, PMP data bit 5, I/O port B5 |
| دبوس 12 | RP4/CN4/PMD4/RB4 — Remappable I/O, CN4, PMP data bit 4, I/O port B4 |
| دبوس 13 | RP3/CN3/PMD3/RB3 — Remappable I/O, CN3, PMP data bit 3, I/O port B3 |
| دبوس 14 | RP2/CN2/PMD2/RB2 — Remappable I/O, CN2, PMP data bit 2, I/O port B2 |
| دبوس 15 | RP1/CN1/PMD1/RB1 — Remappable I/O, CN1, PMP data bit 1, I/O port B1 |
| دبوس 16 | RP0/CN0/PMD0/RB0 — Remappable I/O, CN0, PMP data bit 0, I/O port B0 |
| دبوس 17 | AVDD — Analog supply voltage |
| دبوس 18 | AVSS — Analog ground |
| دبوس 19 | AN0/VREF+/CN8/RA0 — ADC analog input 0, positive reference, CN8, I/O port A0 |
| دبوس 20 | AN1/VREF-/CN9/RA1 — ADC analog input 1, negative reference, CN9, I/O port A1 |
| دبوس 21 | AN2/RA2 — ADC analog input 2, I/O port A2 |
| دبوس 22 | AN3/RA3 — ADC analog input 3, I/O port A3 |
| دبوس 23 | AN4/RA4 — ADC analog input 4, I/O port A4 |
| دبوس 24 | AN5/RA5 — ADC analog input 5, I/O port A5 |
| دبوس 25 | AN6/RA6 — ADC analog input 6, I/O port A6 |
| دبوس 26 | AN7/RA7 — ADC analog input 7, I/O port A7 |
| دبوس 27 | AN8/RB8 — ADC analog input 8, I/O port B8 |
| دبوس 28 | AN9/RB9 — ADC analog input 9, I/O port B9 |
| دبوس 29 | AN10/RB10 — ADC analog input 10, I/O port B10 |
| دبوس 30 | AN11/RB11 — ADC analog input 11, I/O port B11 |
| دبوس 31 | AN12/RB12 — ADC analog input 12, I/O port B12 |
| دبوس 32 | AN13/RB13 — ADC analog input 13, I/O port B13 |
| دبوس 33 | AN14/RB14 — ADC analog input 14, I/O port B14 |
| دبوس 34 | AN15/RB15 — ADC analog input 15, I/O port B15 |
| دبوس 35 | VDD — Digital supply voltage |
| دبوس 36 | VSS — Digital ground |
| دبوس 37 | OSC1/RC1 — External crystal oscillator input / RC clock in |
| دبوس 38 | OSC2/RC2 — External crystal oscillator output |
| دبوس 39 | SOSCI/RC4 — Secondary oscillator (32.768 kHz) input |
| دبوس 40 | SOSCO/RC3 — Secondary oscillator (32.768 kHz) output |
| دبوس 41 | PGED2/RP19/CN19/RC19 — ICSP data I/O 2 / Remappable I/O |
| دبوس 42 | PGEC2/RP18/CN18/RC18 — ICSP clock 2 / Remappable I/O |
| دبوس 43 | PGED1/RC1 — ICSP data I/O 1 (shared with OSC1) |
| دبوس 44 | PGEC1/RC2 — ICSP clock 1 (shared with OSC2) |
| دبوس 45 | RD8 — I/O port D8 |
| دبوس 46 | RD9 — I/O port D9 |
| دبوس 47 | RD10 — I/O port D10 |
| دبوس 48 | RD11 — I/O port D11 |
| دبوس 49 | RD12 — I/O port D12 |
| دبوس 50 | RD13 — I/O port D13 |
| دبوس 51 | RD14 — I/O port D14 |
| دبوس 52 | RD15 — I/O port D15 |
| دبوس 53 | RF0 — I/O port F0 |
| دبوس 54 | RF1 — I/O port F1 |
| دبوس 55 | RF2 — I/O port F2 |
| دبوس 56 | RF3 — I/O port F3 |
| دبوس 57 | RF4 — I/O port F4 |
| دبوس 58 | RF5 — I/O port F5 |
| دبوس 59 | RF6 — I/O port F6 |
| دبوس 60 | RF7 — I/O port F7 |
| دبوس 61 | RG6 — I/O port G6 |
| دبوس 62 | RG7 — I/O port G7 |
| دبوس 63 | RG8 — I/O port G8 |
| دبوس 64 | RG9 — I/O port G9 (EP) |
التطبيقات النموذجية
PIC24HJ128GP506A-I/MR مناسب لـ 6 التطبيقs: BLDC / PMSM Motor Control (FOC), Industrial Sensor Data Acquisition, Digital Signal Processing Front-End, Multi-Rail Point-of-Load System Monitor, Medical Monitoring Device Sub-System, Building Automation / HVAC Controller.
BLDC / PMSM Motor Control (FOC)
The PIC24HJ128GP506A-I/MR's 40 MIPS core, 8-channel 16-bit PWM, and 500 ksps 12-bit ADC map directly to field-oriented control of 3-phase BLDC and PMSM motors. Per Microchip AN1078, the 16-bit PWM delivers 20 ns resolution at 50 MHz which is sufficient for sinusoidal commutation up to ~50 kHz electrical frequency. The 8 DMA channels offload ADC-to-PWM timing from the CPU, leaving headroom for speed/current PI loops. Its industrial -40C to +85C rating suits appliances and small industrial drives without derating.
موصى به
Industrial Sensor Data Acquisition
With up to 16 ADC inputs sampling at 500 ksps and 8 KB SRAM, the PIC24HJ128GP506A-I/MR handles 4-8 sensor channels at >10 kHz aggregate rate with DMA buffering to RAM. Engineers typically run a 100 Hz to 1 kHz sample loop with averaging and digital calibration, then forward processed data via UART or SPI to a host PLC or display. The wide 3.0-3.6 V supply and dual Watchdog Timer support robust 24V-rail industrial backplanes where electrical noise is present. Pin-compatible migration to the PIC24HJ128GP306A-I/MR lets the same PCB ship in two memory tiers.
موصى به
Digital Signal Processing Front-End
Although the PIC24H core lacks the MAC unit of dsPIC33F, the 40 MIPS throughput is adequate for FIR filters up to ~40 taps at 100 kHz, RMS calculations, and Goertzel tone detection. The PIC24HJ128GP506A-I/MR serves as a pre-processor in audio/sonar/vibration front-ends, conditioning data before forwarding to a host processor. With 128 KB Flash it can hold large coefficient tables in program memory mapped via the PSV window. Pin-compatible upgrade to dsPIC33FJ128GP306A-I/MR enables true DSP without PCB rework.
موصى به
Multi-Rail Point-of-Load System Monitor
Telecom and server point-of-load cards use the PIC24HJ128GP506A-I/MR to monitor multiple voltage rails through the 12-bit ADC, sequence power-up via GPIO, and report faults over I2C to a baseboard management controller. The 53 I/O pins accommodate 8-12 enable signals plus status LEDs without external muxing. Industrial temperature rating and the Fail-Safe Clock Monitor maintain operation during oscillator fault conditions common in hot-running racks.
موصى به
Medical Monitoring Device Sub-System
Portable patient monitors and diagnostic peripherals rely on the PIC24HJ128GP506A-I/MR's deterministic interrupt latency to drive LCDs, manage button inputs, and stream sensor data over UART/SPI to a host CPU. The wide Flash headroom accommodates multi-language UI assets and field-updatable bootloader. Its industrial temperature rating and low-power sleep modes (down to ~20 uA) suit battery-powered handheld devices where the IEC 60601-1 isolation barrier is implemented externally.
موصى به
Building Automation / HVAC Controller
The PIC24HJ128GP506A-I/MR integrates seamlessly into HVAC controllers that manage fans, dampers, and temperature sensors with PID control loops running on the 40 MIPS core. Up to two I2C buses permit multi-master sensor networks (temperature, humidity, CO2) while UART/SPI bridges to a building automation backbone such as Modbus or BACnet. The exposed VQFN thermal pad keeps junction temperature within spec when driving multiple relay drivers from the GPIO pins.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PIC24HJ128GP506A-I/MR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | PIC24HJ128GP306A-I/MR | PIC24HJ128GP306-I/MR | PIC24HJ128GP306A-E/MR | dsPIC33FJ128GP306A-I/MR |
|---|---|---|---|---|---|
| Package | 64-VQFN (9x9) - MR | 64-VQFN (9x9) - MR (same) | 64-VQFN (9x9) - MR (same) | 64-VQFN (9x9) - MR (same) | 64-VQFN (9x9) - MR (same) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | PIC24H 16-bit, 40 MIPS | PIC24H 16-bit, 40 MIPS | PIC24H 16-bit, 40 MIPS | PIC24H 16-bit, 40 MIPS | dsPIC33F 16-bit DSP, 50 MIPS |
| Flash Memory | 128 KB | 64 KB (-50%) | 64 KB (-50%) | 64 KB (-50%) | 128 KB (same) |
| RAM | 8 KB | 8 KB (same) | 8 KB (same) | 8 KB (same) | 8 KB (same) |
| ADC | 12-bit, 16-ch, 500 ksps | 12-bit, 16-ch, 500 ksps | 12-bit, 16-ch, 500 ksps | 12-bit, 16-ch, 500 ksps | 12-bit, 16-ch, 500 ksps |
| DSP Engine | No (PIC24H CPU) | No | No | No | Yes (MAC unit) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +125C (Extended) | -40C to +85C |
| Silicon Revision | A-revision (GP506A) | A-revision (GP306A) | Pre-A (GP306) | A-revision (GP306A-E) | A-revision (dsPIC33F) |
أبرز الفروقات
- Larger 128 KB Flash on the same 64-VQFN footprint (مقابلPIC24HJ128GP306A-I/MR)
- DSP upgrade path exists on identical footprint (مقابلdsPIC33FJ128GP306A-I/MR)
- Industrial temperature vs Extended temperature at same cost (مقابلPIC24HJ128GP306A-E/MR)
ملاحظات التصميم
The 64-VQFN (9x9) package relies on the bottom exposed pad (EP) for heat dissipation. Estimate: at 80 MHz / 3.3 V with all peripherals active, ICC is approximately 70 mA (~230 mW). Solder the EP directly to a top-layer copper pour of at least 1 sq inch, stitch it with 4-9 thermal vias (0.3 mm drill, 0.5 mm pitch) to the inner ground plane, and the resulting theta_JA is approximately 28 C/W, which keeps the junction at +85C max when ambient is +60C. Do NOT leave the EP floating - the device will overheat and trigger thermal reset.
Place the decoupling network immediately at each VDD/VSS pair: a 100 nF X7R ceramic as close as possible (<2 mm trace) to the pin plus a bulk 4.7-10 uF tantalum or ceramic on the board supply entry. The PIC24HJ128GP506A-I/MR has multiple VDD/VSS pairs (digital, analog AVDD/AVSS) - bypass each independently. For analog ANx inputs, route a guard trace tied to AVSS between analog and digital signals to minimize digital noise coupling into ADC readings.
Do NOT connect PGEC1/PGED1 to the same pins as the high-speed oscillator (OSC1/OSC2). On 64-VQFN the PGECx/PGEDx pairs are multiplexed: PGEC1/PGED1 share pins with OSC1/OSC2, so using a crystal on those pins disables ICSP on that pair. Choose the PGEC2/PGED2 pair on RC18/RC19 for ICSP debugging while keeping the primary oscillator free to run. Also ensure all VSS pins (including AVSS) are tied to ground - leaving any floating breaks programming and ADC reference.
Route the 12-bit ADC analog inputs (AN0-AN15) as short, parallel traces with a ground guard on each side; keep them away from PWM switching signals (>10 mm or with ground plane between). For PWM-driven motor applications, place gate-driver signals on inner layers to avoid injecting common-mode noise onto the ADC bus. The crystal oscillator traces (OSC1/OSC2, SOSCI/SOSCO) should be <5 mm and surrounded by a continuous ground pour to maintain jitter below 50 ps RMS, per the PIC24H datasheet AC characteristics.
معلومات الامتثال
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - the part targets industrial (-40C to +85C) not automotive grade. For automotive applications consider dsPIC33F AEC-Q100 variants. REACH and conflict-minerals statements available from Microchip corporate compliance.
