STM32F429VGT6 - 180MHz Cortex-M4 MCU 1MB Flash LQFP-100 | ST (Tape & Reel)
MPN: STM32F429VGT6 ✓ نشطSTM32F429VGT6 نظرة عامة
An ARM Cortex-M4 microcontroller is a 32-bit RISC core with hardware floating-point unit, single-cycle MAC, and SIMD instructions widely adopted for deterministic real-time embedded designs. Within ST's portfolio, the STM32F4 family targets applications where the Cortex-M3 lacks DSP performance, while remaining compatible with the Cortex-M software ecosystem. The ART Accelerator is a flash-front-end IP block that prefetches instructions and data into a tightly-coupled instruction cache, eliminating flash wait states so the core can execute from flash at its full 180 MHz rating without throughput penalty - a meaningful advantage over older flash-stalled designs.
Key features of the STM32F429VGT6 include: 1 MB Flash, 192 KB SRAM, 4 KB backup SRAM, TFT LCD controller, USB OTG HS/FS with dedicated PHY, 10/100 Ethernet MAC with IEEE 1588v2 support, two CAN 2.0B active controllers, three 12-bit ADCs at 2.4 MSPS, two 12-bit DACs, 17 timers, up to 82 fast GPIOs, and the Crypto/hash hardware accelerator (AES, SHA-1, MD5). The integrated TFT controller supports up to XGA resolution and includes a Chrom-ART (DMA2D) graphics accelerator for efficient image blending without CPU load.
Typical applications driving STM32F429VGT6 selection are: HMI panels with TFT displays, industrial control units, PLCs, motor drives, point-of-sale terminals, smart-grid metering, medical instrumentation with TFT readouts, and IoT gateways requiring Ethernet + TLS. The on-chip Crypto/hash block accelerates TLS handshakes and secure boot, while the TFT controller and DMA2D engine remove the need for an external graphics controller in mid-resolution panels. The wide connectivity mix (USB HS, Ethernet, CAN, SDMMC) lets a single chip replace multi-IC designs.
When designing with this device, allocate sufficient decoupling (100 nF per VDD pin pair) and keep the LQFP-100 ground paddle (when present on the die flag) stitched with vias to inner ground planes. For TFT clock rates above 40 MHz, follow ST application note AN4861 on LCD-TFT PCB routing to control EMI. The VBAT domain allows RTC retention and 4 KB backup SRAM to survive VDD loss when supplied by a coin cell.
This page synthesizes distributor pricing, verified drop-in alternatives, application-specific guidance, and practical design notes not found in the manufacturer datasheet alone, providing actionable information for procurement and hardware engineers.
بدائل مباشرة لـ STM32F429VGT6 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع STM32F429VGT6 (نفس عامل الشكل والبصمة) — يختلف في Package, Flash Memory, SRAM, Core, ADC.
STM32F427VGT6TR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F439VGT6TR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F407VGT6TR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←STM32F429VET6
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←GD32F450VGT6
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F429ZGT6
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←STM32F429VGT6 الحدود القصوى والخصائص الكهربائية
| Core | ARM Cortex-M4 with FPU and DSP instructions |
| CPU Maximum Frequency | 180 MHz |
| DMIPS Performance | 225 DMIPS (1.25 DMIPS/MHz, Dhrystone 2.1) |
| Flash Memory | 1 MB |
| SRAM | 192 KB (including 4 KB backup SRAM) |
| Operating Voltage | 1.8 V to 3.6 V |
| العلبة | LQFP-100 (14 x 14 mm) |
| نوع التركيب | Surface Mount |
| درجة حرارة التشغيل | -40 C to +85 C (grade 6) |
| ART Accelerator | Yes (0-wait-state Flash execution) |
| MPU | Yes (memory protection unit) |
| LCD-TFT Controller | Yes, up to XGA resolution |
| DMA2D (Chrom-ART) | Yes |
| USB OTG | HS + FS (with on-chip PHY) |
| Ethernet MAC | 10/100 with IEEE 1588v2 |
| CAN Controllers | 2 x CAN 2.0B active |
| ADC | 3 x 12-bit, up to 2.4 MSPS |
| DAC | 2 x 12-bit |
| Timers | 17 (including 12 x 16-bit, 2 x 32-bit) |
| GPIOs | Up to 82 fast GPIOs |
| Crypto/Hash Accelerator | AES-128/192/256, SHA-1, MD5, 3DES |
| SDMMC | 1 x SDMMC host |
| Communication Peripherals | UART, SPI, I2C, SAI, SPDIF-Rx |
| حالة RoHS | Compliant |
| مستوى MSL | 3 (168 hours) |
تكوين أطراف STM32F429VGT6
| دبوس 1 | PE02 — GPIO PE2, TRACECLK |
| دبوس 2 | PE03 — GPIO PE3, TRACED0 |
| دبوس 3 | PE04 — GPIO PE4, TRACED1 |
| دبوس 4 | PE05 — GPIO PE5, TRACED2 |
| دبوس 5 | PE06 — GPIO PE6, TRACED3 |
| دبوس 6 | VBAT — Battery domain supply for RTC and backup SRAM |
| دبوس 7 | PC13 — GPIO PC13, anti-tamper (RTC) |
| دبوس 8 | PC14 — GPIO PC14, OSC32_IN |
| دبوس 9 | PC15 — GPIO PC15, OSC32_OUT |
| دبوس 10 | VSS — Digital ground |
| دبوس 11 | VDD — Digital supply 1.8V-3.6V |
| دبوس 12 | PH00 — GPIO PH0, OSC_IN |
| دبوس 13 | PH01 — GPIO PH1, OSC_OUT |
| دبوس 14 | NRST — Reset, active low |
| دبوس 15 | PC00 — GPIO PC0, ADC123_IN10 |
| دبوس 16 | PC01 — GPIO PC1, ADC123_IN11 |
| دبوس 17 | PC02 — GPIO PC2, ADC123_IN12 |
| دبوس 18 | PC03 — GPIO PC3, ADC123_IN13 |
| دبوس 19 | VSSA — Analog ground |
| دبوس 20 | VDDA — Analog supply 1.8V-3.6V |
| دبوس 21 | PA00 — GPIO PA0, WKUP, ADC123_IN0, TIM5_CH1 |
| دبوس 22 | PA01 — GPIO PA1, ADC123_IN1, TIM5_CH2 |
| دبوس 23 | PA02 — GPIO PA2, ADC123_IN2, TIM5_CH3, USART2_TX |
| دبوس 24 | PA03 — GPIO PA3, ADC123_IN3, TIM5_CH4, USART2_RX |
| دبوس 25 | VSS — Digital ground |
| دبوس 26 | VDD — Digital supply 1.8V-3.6V |
| دبوس 27 | PA04 — GPIO PA4, ADC12_IN4, DAC_OUT1, SPI1_NSS |
| دبوس 28 | PA05 — GPIO PA5, ADC12_IN5, DAC_OUT2, SPI1_SCK |
| دبوس 29 | PA06 — GPIO PA6, ADC12_IN6, SPI1_MISO, TIM13_CH1 |
| دبوس 30 | PA07 — GPIO PA7, ADC12_IN7, SPI1_MOSI, TIM14_CH1 |
| دبوس 31 | PC04 — GPIO PC4, ADC12_IN14 |
| دبوس 32 | PC05 — GPIO PC5, ADC12_IN15 |
| دبوس 33 | PB00 — GPIO PB0, ADC12_IN8, TIM3_CH3 |
| دبوس 34 | PB01 — GPIO PB1, ADC12_IN9, TIM3_CH4 |
| دبوس 35 | PB02 — GPIO PB2, BOOT1 |
| دبوس 36 | PE07 — GPIO PE7, TIM1_ETR |
| دبوس 37 | PE08 — GPIO PE8, TIM1_CH1N |
| دبوس 38 | PE09 — GPIO PE9, TIM1_CH1 |
| دبوس 39 | PE10 — GPIO PE10, TIM1_CH2N |
| دبوس 40 | PE11 — GPIO PE11, TIM1_CH2 |
| دبوس 41 | PE12 — GPIO PE12, TIM1_CH3N |
| دبوس 42 | PE13 — GPIO PE13, TIM1_CH3 |
| دبوس 43 | PE14 — GPIO PE14, TIM1_CH4 |
| دبوس 44 | PE15 — GPIO PE15, TIM1_BKIN |
| دبوس 45 | PB10 — GPIO PB10, I2C2_SCL, USART3_TX, TIM2_CH3 |
| دبوس 46 | PB11 — GPIO PB11, I2C2_SDA, USART3_RX, TIM2_CH4 |
| دبوس 47 | VCAP_1 — Core LDO bypass (1.2V, 4.7uF cap to ground) |
| دبوس 48 | VDD — Digital supply 1.8V-3.6V |
| دبوس 49 | PB12 — GPIO PB12, SPI2_NSS, I2S2_WS, TIM1_BKIN, CAN2_RX |
| دبوس 50 | PB13 — GPIO PB13, SPI2_SCK, I2S2_CK, CAN2_TX |
| دبوس 51 | PB14 — GPIO PB14, SPI2_MISO, TIM12_CH1, USART1_RTS |
| دبوس 52 | PB15 — GPIO PB15, SPI2_MOSI, TIM12_CH2, USART1_CTS |
| دبوس 53 | PD08 — GPIO PD8, USART3_TX, FSMC_D13 |
| دبوس 54 | PD09 — GPIO PD9, USART3_RX, FSMC_D14 |
| دبوس 55 | PD10 — GPIO PD10, FSMC_D15 |
| دبوس 56 | PD11 — GPIO PD11, FSMC_A16 |
| دبوس 57 | PD12 — GPIO PD12, FSMC_A17, TIM4_CH1 |
| دبوس 58 | PD13 — GPIO PD13, FSMC_A18, TIM4_CH2 |
| دبوس 59 | VSS — Digital ground |
| دبوس 60 | VDD — Digital supply 1.8V-3.6V |
| دبوس 61 | PD14 — GPIO PD14, FSMC_D0, TIM4_CH3 |
| دبوس 62 | PD15 — GPIO PD15, FSMC_D1, TIM4_CH4 |
| دبوس 63 | PG02 — GPIO PG2, FSMC_A23 |
| دبوس 64 | PG03 — GPIO PG3, FSMC_A24 |
| دبوس 65 | PG04 — GPIO PG4, FSMC_A25 |
| دبوس 66 | PG05 — GPIO PG5, FSMC_NE3 |
| دبوس 67 | PG06 — GPIO PG6, FSMC_NE4, INT6 |
| دبوس 68 | PG07 — GPIO PG7, FSMC_INT3 |
| دبوس 69 | PG08 — GPIO PG8, FSMC_CLK |
| دبوس 70 | VSS — Digital ground |
| دبوس 71 | VDD — Digital supply 1.8V-3.6V |
| دبوس 72 | PC06 — GPIO PC6, USART6_TX, TIM3_CH1, FSMC_NWAIT |
| دبوس 73 | PC07 — GPIO PC7, USART6_RX, TIM3_CH2, FSMC_NE1 |
| دبوس 74 | PC08 — GPIO PC8, USART6_CK, TIM3_CH3, SDMMC_D0 |
| دبوس 75 | PC09 — GPIO PC9, USART6_RTS, TIM3_CH4, SDMMC_D1 |
| دبوس 76 | PA08 — GPIO PA8, USART1_CK, TIM1_CH1, MCO1 |
| دبوس 77 | PA09 — GPIO PA9, USART1_TX, TIM1_CH2, OTG_FS_VBUS |
| دبوس 78 | PA10 — GPIO PA10, USART1_RX, TIM1_CH3, OTG_FS_ID |
| دبوس 79 | PA11 — GPIO PA11, OTG_FS_DM, CAN1_RX, TIM1_CH4 |
| دبوس 80 | PA12 — GPIO PA12, OTG_FS_DP, CAN1_TX, TIM1_CH5 |
| دبوس 81 | PA13 — GPIO PA13, JTMS-SWDIO |
| دبوس 82 | VSS — Digital ground |
| دبوس 83 | VDD — Digital supply 1.8V-3.6V |
| دبوس 84 | PA14 — GPIO PA14, JTCK-SWCLK |
| دبوس 85 | PA15 — GPIO PA15, JTDI, SPI3_NSS, TIM2_CH1 |
| دبوس 86 | PC10 — GPIO PC10, USART4_TX, SDMMC_D2, FSMC_NE2 |
| دبوس 87 | PC11 — GPIO PC11, USART4_RX, SDMMC_D3 |
| دبوس 88 | PC12 — GPIO PC12, USART5_TX, SDMMC_CK |
| دبوس 89 | PD00 — GPIO PD0, FSMC_D2, CAN1_RX |
| دبوس 90 | PD01 — GPIO PD1, FSMC_D3, CAN1_TX |
| دبوس 91 | PD02 — GPIO PD2, SDMMC_CMD, TIM3_ETR, USART5_RX |
| دبوس 92 | PD03 — GPIO PD3, FSMC_CLK, USART2_CTS |
| دبوس 93 | PD04 — GPIO PD4, FSMC_NOE, USART2_RTS |
| دبوس 94 | PD05 — GPIO PD5, FSMC_NWE, USART2_TX |
| دبوس 95 | VSSA — Analog ground |
| دبوس 96 | VDDA — Analog supply 1.8V-3.6V |
| دبوس 97 | PB06 — GPIO PB6, I2C1_SCL, USART1_TX, TIM4_CH1 |
| دبوس 98 | PB07 — GPIO PB7, I2C1_SDA, USART1_RX, TIM4_CH2 |
| دبوس 99 | PB08 — GPIO PB8, TIM4_CH3, I2C1_SCL, CAN1_RX |
| دبوس 100 | PB09 — GPIO PB9, TIM4_CH4, I2C1_SDA, CAN1_TX |
التطبيقات النموذجية
STM32F429VGT6 مناسب لـ 6 التطبيقs: TFT-LCD HMI Panel, Industrial Motor Drive, Smart Energy Metering, Medical Instrumentation, IoT Gateway with Ethernet, Point-of-Sale Terminal.
TFT-LCD HMI Panel
The STM32F429VGT6 is purpose-built for TFT-LCD HMI panels in industrial controls and consumer devices, integrating a hardware LCD-TFT controller that drives displays up to XGA (1024x768) without an external graphics controller. Combined with the Chrom-ART DMA2D engine that offloads 2D image blending, rectangles, and color-conversion from the CPU, the device delivers fluid UI performance even with the 180 MHz Cortex-M4 core busy on application logic. The 1 MB internal Flash allows storing full framebuffers and font libraries on-chip. Engineers typically pair this MCU with 4.3"-7" TFT modules over the RGB parallel interface, and use DMA2D for sprites and antialiased text. Compared to older STM32F1 designs that required an external SSD1963 or RA8875 controller, the F429 saves BOM cost, PCB area, and software complexity for mid-size displays. Its AES/SHA crypto also enables secure boot and TLS for connected HMI panels.
موصى به
Industrial Motor Drive
In industrial motor drives and servo controllers, the STM32F429VGT6 provides three 12-bit ADCs at 2.4 MSPS, two 12-bit DACs, and 17 timers including advanced-control timers with complementary PWM and dead-time insertion. Field-Oriented Control (FOC) algorithms on sensorless BLDC and PMSM motors run efficiently on the Cortex-M4 with hardware FPU at 180 MHz, achieving sub-10us control loop times. The two CAN 2.0B active controllers support CANopen and DeviceNet protocols for industrial networking. Hardware AES acceleration and 1 MB Flash enable local fault-logging storage. Designers must follow application note AN4720 on PFC and AN4944 on FOC firmware to leverage the FPU effectively. The 1.8 V to 3.6 V supply range supports both 3.3 V logic and battery-backed designs.
موصى به
Smart Energy Metering
For smart electricity, water, and gas meters, the STM32F429VGT6 delivers the security, connectivity, and accuracy required for IEC 62053-22 class 0.2 metrology. The hardware AES-256 and SHA accelerators accelerate TLS 1.2 handshakes for DLMS/COSEM protocols over TCP/IP, while the three 12-bit ADCs sample voltage and current at 2.4 MSPS for accurate power calculations. The integrated 10/100 Ethernet MAC with IEEE 1588v2 hardware timestamping provides sub-microsecond synchronization for substation automation. Backup SRAM retains critical metering logs across power outages, and the VBAT domain keeps the calendar running on a coin cell. The 1 MB Flash accommodates full TLS stacks and metering application firmware.
موصى به
Medical Instrumentation
In medical instrumentation - patient monitors, infusion pumps, and portable diagnostic devices - the STM32F429VGT6 provides the deterministic Cortex-M4F performance needed for signal-processing tasks like FFT-based heart rate extraction and filter-based ECG denoising. The TFT-LCD controller with Chrom-ART acceleration drives bedside monitors with clear graphical readouts at 800x480 resolution. Hardware AES-128/256 acceleration enables HIPAA-compliant data encryption over BLE or Wi-Fi links. The -40 C to +85 C industrial temperature range covers most clinical environments, and the 1 MB Flash allows storing multiple waveform libraries on-chip. The 192 KB SRAM accommodates real-time DSP buffers without external memory.
موصى به
IoT Gateway with Ethernet
For IoT gateways aggregating sensor data from industrial protocols, the STM32F429VGT6 combines 10/100 Ethernet with hardware TLS acceleration, dual USB OTG, and SDMMC for local storage. Engineers can run lightweight MQTT brokers or Modbus TCP servers directly on the Cortex-M4 at 180 MHz, with the AES/SHA hardware block accelerating TLS 1.2 handshakes to under 200ms. The 4 KB backup SRAM preserves network credentials and last-known state across power cycles, while the VBAT domain retains RTC time. SDMMC supports microSD cards for log retention up to 32 GB. The part supports FreeRTOS, AzureRTOS, and Zephyr out-of-box, simplifying cloud-connect firmware.
موصى به
Point-of-Sale Terminal
POS terminals benefit from the STM32F429VGT6's combination of TFT-LCD controller for the operator display, USB OTG HS for fast peripheral connectivity (NFC readers, EMV chip-card interfaces), Ethernet MAC for payment-gateway connectivity, and hardware AES for PCI-PTS PIN encryption. The 1 MB Flash stores payment application firmware and certificate chains, while the 192 KB SRAM accommodates TCP/IP stacks plus TLS session buffers. The two CAN controllers support older POS peripherals. The -40 C to +85 C industrial grade matches retail-environment requirements. Designers can use the Chrom-ART engine for animated merchant logos during transaction prompts.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ STM32F429VGT6 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | STM32F427VGT6TR | STM32F439VGT6TR | STM32F407VGT6TR | STM32F429VET6 | GD32F450VGT6 |
|---|---|---|---|---|---|---|
| Package | LQFP-100 (14x14) | LQFP-100 (14x14) - same | LQFP-100 (14x14) - same | LQFP-100 (14x14) - same | LQFP-100 (14x14) - same | LQFP-100 (14x14) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Core | Cortex-M4F 180 MHz | Cortex-M4F 180 MHz - same | Cortex-M4F 180 MHz - same | Cortex-M4F 168 MHz (-7%) | Cortex-M4F 180 MHz - same | Cortex-M4F 200 MHz (+11%) |
| Flash Memory | 1 MB | 1 MB - same | 1 MB - same | 1 MB - same | 512 KB (-50%) | 1 MB - same |
| SRAM | 192 KB | 192 KB - same | 192 KB - same | 192 KB - same | 192 KB - same | 256 KB (+33%) |
| TFT-LCD Controller | Yes | No (F427 lacks TFT) | Yes - same | No (F407 lacks TFT) | Yes - same | No |
| Crypto/Hash | AES-128/192/256, SHA-1, MD5, 3DES | AES/SHA/MD5 - same | AES-256, SHA-256, RSA, ECC (enhanced) | AES/SHA/MD5 - same | AES/SHA/MD5 - same | AES/SHA (no 3DES) |
| Ethernet MAC | 10/100 + IEEE 1588v2 | 10/100 + IEEE 1588v2 - same | 10/100 + IEEE 1588v2 - same | 10/100 + IEEE 1588v2 - same | 10/100 + IEEE 1588v2 - same | 10/100 (no 1588v2) |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V - same | 1.8 V to 3.6 V - same | 1.8 V to 3.6 V - same | 1.8 V to 3.6 V - same | 2.6 V to 3.6 V |
| Approx Unit Price (qty 1000) | ~$11.94 | ~$10.50 (-12%) | ~$13.50 (+13%) | ~$9.80 (-18%) | ~$9.20 (-23%) | ~$3.50 (-71%) |
أبرز الفروقات
- Integrated TFT-LCD controller with Chrom-ART DMA2D (مقابلSTM32F407VGT6TR)
- Hardware AES/SHA/MD5/3DES crypto accelerator (مقابلSTM32F205VGT6)
- Adaptive Real-Time (ART) Accelerator with 0-wait-state Flash (مقابلSTM32F103 (Cortex-M3))
- Cost-down option with same pinout (مقابلSTM32F427VGT6TR)
ملاحظات التصميم
Decouple every VDD/VDDA pair with a 100 nF ceramic capacitor placed within 5 mm of the pin. Add a 4.7 uF bulk capacitor on VCAP_1 (pin 47) to stabilize the internal 1.2 V LDO. Place a 10 uF bulk capacitor on VBAT (pin 6) when using RTC or backup SRAM retention. Use separate analog and digital ground planes stitched together at one point near the MCU VDDA pin. For noise-sensitive ADC applications, filter VDDA with a ferrite bead.
At maximum CPU activity (180 MHz, all peripherals running, 3.6 V supply), the STM32F429VGT6 draws approximately 95 mA, dissipating roughly 340 mW. The LQFP-100 package has a thermal resistance theta_JA of approximately 43 C/W on a 4-layer JEDEC test board, giving a junction temperature rise of 15 C above ambient at full load. For industrial-grade parts rated to +85 C, this leaves 65 C of margin at +25 C ambient. No external heatsink is required, but ensure adequate ground plane copper for heat spreading.
Route TFT-LCD data and clock signals (RGB interface) as matched-length traces within 50 mil tolerance to avoid skew artifacts. Keep TFT clock traces short and surrounded by ground; refer to ST application note AN4861 for LCD-TFT PCB layout guidelines. Place the 32.768 kHz crystal within 5 mm of pins PC14/PC15 (OSC32_IN/OUT), and the HSE crystal within 5 mm of pins PH0/PH1 (OSC_IN/OUT). Use guard traces around the HSE traces if the design is noise-sensitive. SD card signals should be length-matched within 1 mm.
Do not leave VCAP_1 floating - the internal LDO will not regulate and the part will appear dead. Never apply 5V to any GPIO, despite some STM32 parts being 5V-tolerant; the F429 is strictly 3.3 V. When using the TFT controller in 16-bit mode, ensure FSMC bus is configured for the correct memory width. Boot0 pin must be sampled correctly for boot mode selection - leaving it floating causes intermittent boot failures. The SD card SDMMC interface requires external pull-ups on the CMD and DAT lines for proper operation.
معلومات الامتثال
Industrial-grade part (-40 C to +85 C), not AEC-Q100 qualified. For automotive applications, use STM32F429VGT6-Q1 or related parts.
