Microchip Technology

SY88893VKI - 155Mbps PECL Limiting Post Amp | Microchip

MPN: SY88893VKI ✓ نشط
3.3 V or 5 V single supply Vdss 10-TFSOP, 10-MSOP (0.118 in, 3.00 mm width) Package
الحد الأدنى للطلب: 1 |

SY88893VKI نظرة عامة

The Microchip Technology SY88893VKI is a 3.3 V/5 V low-power limiting post amplifier for 155 Mbps PECL optical networks, with a chatter-free TTL signal-detect output and a TTL enable input, supplied in a 10-pin MSOP (10-TFSOP, 0.118 in / 3.00 mm width) package.

What is a limiting post amplifier? A post amplifier (also called a limiting amplifier or post driver) sits at the receive end of a high-speed differential link, between the photodiode or line receiver and the system's logic or clock-and-data-recovery circuitry. It restores a small, degraded input signal to full logic swing, squares it up, and drives the next stage over copper or into a parallel TTL interface. A "limiting" post amplifier adds amplitude limiting and threshold slicing so that noise and intersymbol interference are rejected before the signal is passed downstream. In the optical-networking hierarchy it belongs to the line-driver and transceiver front-end family, above the photoreceiver and below the CDR and parallel-to-serial converter.

Key features of the SY88893 include operation from a single 3.3 V or 5 V supply, data rates to 155 Mbps, PECL-compatible differential outputs, a chatter-free TTL signal-detect (SD) output that reports loss of optical or input signal without false toggling, and a TTL enable (EN) input that forces the outputs into a known state during system reset or power sequencing. Low-power limiting post-amplifier architecture keeps dissipation low enough for the small 10-MSOP footprint.

Technically, the device accepts a small-signal differential PECL input, amplifies and limits it, and presents ECL/PECL-level differential outputs for a 155 Mbps optical transceiver line. The TTL SD output is designed so that its state changes only when the input crosses the detection threshold, which prevents chatter when the optical input is marginal or when the far-end transmitter is disabled. The TTL-compatible enable input allows the host to tri-state or mute the outputs without removing power from the module.

Typical applications include 155 Mbps SONET/SDH line receivers, PECL-to-TTL signal-detect interfaces inside pluggable optical modules, post-amplifier stages in 3.3 V and 5 V telecom transceivers, and legacy copper-to-fiber line-card retiming paths.

When laying out this part, keep the differential input pair short, matched, and referenced to a solid ground plane, and route PECL outputs as a tight 100 ohm differential pair. Avoid long stubs between the amplifier and the downstream TTL logic, since the amplitude-limited transition edges are where ringing is most likely to appear.

This page brings together the manufacturer description, distributor availability, drop-in ordering-code options, and practical PCB-level guidance that is not repeated on the distributor catalogue pages, helping engineers qualify the device and plan sourcing in one place.

بدائل مباشرة لـ SY88893VKI — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

SY88893VKC

✅ بديل مباشر
Microchip Technology
📦 10-MSOP (10-TFSOP)
Limiting postamplifier · 155 Mbps · 3.3 V or 5 V · PECL · TTL · TTL · Chatter-free · Optical networks

تواصل لمعرفة السعر

عرض ورقة البيانات ←

SY88893

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 10-MSOP (10-TFSOP)
Base ordering code of the same device; identical 155 Mbps PECL limiting post amplifier and 10-MSOP footprint, no functional or parametric difference

📋 بديل مرجعي (غير موجود في الكتالوج)

SY88893VKI-TR

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 10-MSOP (10-TFSOP)
Same die and 10-MSOP footprint with industrial grade; differs only in tape-and-reel shipping form versus tube, electrical ratings identical

📋 بديل مرجعي (غير موجود في الكتالوج)

SY88893VKC-TR

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 10-MSOP (10-TFSOP)
Same die and 10-MSOP footprint with commercial grade; differs only in tape-and-reel shipping form versus tube, electrical ratings identical

📋 بديل مرجعي (غير موجود في الكتالوج)

SY88893VKI الحدود القصوى والخصائص الكهربائية

Device Type Limiting post amplifier (low-power PECL post driver)
Maximum Data Rate 155 Mbps
جهد التغذية 3.3 V or 5 V single supply
Output Logic Family PECL (differential)
Signal Detect Output TTL, chatter-free
Enable Input TTL-compatible EN input
Input Stage Differential limiting amplifier
Application Optical networks, 155 Mbps PECL/TTL interfaces
العلبة 10-TFSOP, 10-MSOP (0.118 in, 3.00 mm width)
نوع التركيب Surface Mount
Packaging Tube
Lead-Free / RoHS Compliant per Microchip product documentation
Manufacturer Microchip Technology (originally Micrel Semiconductor)
Observed Distributor Stock 6,000 pieces (one distributor listing)

دليل تكوين أطراف SY88893VKI 10-tfsop, 10-msop (0.118 in, 3.00 mm width)

تكوين الأطراف لـ SY88893VKI (حزمة 10-tfsop, 10-msop (0.118 in, 3.00 mm width)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 10-tfsop, 10-msop (0.118 in, 3.00 mm width) لـ SY88893VKI

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SY88893VKI.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

SY88893VKI مناسب لـ 6 التطبيقs: 155 Mbps SONET/SDH Optical Line Receiver, PECL-to-TTL Signal Detect Interface in Pluggable Optical Modules, 3.3 V / 5 V Telecom Transceiver Post-Amplifier Stage, Copper-to-Fiber Line Card Retiming Path, Optical Link Loss-of-Signal Detection and Alarm Reporting, Test and Measurement Pulse Conditioning.

🌐

155 Mbps SONET/SDH Optical Line Receiver

The SY88893VKI fits at the receive end of a 155 Mbps optical tributary path, where a photoreceiver produces a small differential PECL signal that must be regenerated before it reaches the clock-and-data-recovery or framer input. Because the device is specified for 155 Mbps operation from a single 3.3 V or 5 V supply, the same part covers both 3.3 V and 5 V line-card generations, and the low-power limiting architecture keeps the dissipation manageable inside the small 10-MSOP (10-TFSOP, 0.118 in / 3.00 mm) footprint. The amplitude limiting and threshold slicing remove intersymbol interference that a plain linear amplifier would pass through, giving the downstream CDR a stable, full-swing input. The chatter-free TTL signal-detect output lets the line card know that the far-end transmitter is present and silent when the optical path is dark.

🧩

PECL-to-TTL Signal Detect Interface in Pluggable Optical Modules

Inside a pluggable optical transceiver, the host controller needs a TTL-level indication of whether light is present at the receiver, not a raw differential PECL signal. The SY88893VKI provides this directly: the TTL signal-detect output is specified as chatter-free, so it will not oscillate when the optical input level hovers near the detection threshold, a common condition during insertion or during an automatic power-control transition. Placing the amplifier after the photoreceiver in the 10-MSOP footprint keeps the module's analog section compact and leaves room for the SFP cage mechanics. The TTL-compatible enable input adds a second benefit, letting the controller mute the outputs during reset or laser shutdown and avoid transient edges on a link that is being reconfigured.

⚡

3.3 V / 5 V Telecom Transceiver Post-Amplifier Stage

Transceiver designs in this class often share a platform across 3.3 V and 5 V module variants, and the SY88893VKI supports either supply from a single part number, which simplifies qualification and inventory. Running the device from the same rail as the module's digital section removes the need for a level translator between the PECL receive chain and the logic domain. The limiting post-amplifier behaviour ensures that small variations in received optical power do not translate into output jitter or duty-cycle distortion at the receiver output. For designs with tight board-area budgets, the 10-MSOP package with a 3.00 mm body width is considerably smaller than the discrete gain-block plus comparator assemblies it typically replaces, and the TTL enable input supports per-channel shutdown during link bring-up.

🔧

Copper-to-Fiber Line Card Retiming Path

In a line card that bridges an electrical tributary interface to an optical port, the electrical input arrives as a small, noisy differential signal, and the SY88893VKI regenerates it into a clean PECL pair that can cross the card and drive the optical transmit path. The limiting stage rejects additive noise and jitter excursions that would otherwise accumulate across the card, and the 155 Mbps figure places it squarely in the SDH/SONET tributary rate class. The 10-MSOP footprint allows the retiming function to sit close to the connector or cage rather than in the centre of the card, which shortens the sensitive input leg. The TTL enable input is useful here as well, since the retimer can be held in a benign state while the card boots and its protection circuits settle.

📡

Optical Link Loss-of-Signal Detection and Alarm Reporting

Loss-of-signal reporting is one of the functions where the SY88893VKI is commonly deployed, because the TTL signal-detect output is specified as chatter-free and therefore stable when the input signal sits near the detection threshold. That stability matters in networks where a single noisy fiber or a marginal connector would otherwise produce a flapping alarm and trigger unnecessary protection switching. In such systems the amplifier is placed at the head of the receive chain so that the detection decision is made on the restored signal rather than on the raw photoreceiver output, which improves decision consistency across temperature and power-supply variation. The TTL enable input lets the monitoring controller mute the link while it performs a controlled reset, preventing a false loss-of-signal report during the event.

🖥️

Test and Measurement Pulse Conditioning

Bench and instrument designs that recover low-amplitude differential signals often use a limiting post amplifier as the final stage before a comparator or a sampling front end, because the limiting action gives predictable, repeatable edge shapes rather than the soft, noise-sensitive transitions of a linear amplifier. The SY88893VKI brings this function into a 10-MSOP (10-TFSOP, 0.118 in / 3.00 mm width) package that fits into a compact instrument front end, and its operation from a single 3.3 V or 5 V supply simplifies the power tree of a bench module. The TTL signal-detect output is also useful in a test fixture, where it can be used as a simple live/dead indicator for the DUT link under test. Because the part operates up to 155 Mbps, it suits pulse-per-bit and low-rate NRZ test patterns rather than multi-gigabit serial analysis.

ملخص المنتجات الموصى بها

MCP3561RT-E/MS Delta-sigma ADC for optical power / link monitoring يُستخدم في: 155 Mbps SONET/SDH Optical Line Receiver MCP6061-I/SN Low-noise op-amp for analog monitor channels يُستخدم في: 155 Mbps SONET/SDH Optical Line Receiver, PECL-to-TTL Signal Detect Interface in Pluggable Optical Modules, Optical Link Loss-of-Signal Detection and Alarm Reporting MCP3426A5-E/MC Microchip Technology يُستخدم في: PECL-to-TTL Signal Detect Interface in Pluggable Optical Modules, Copper-to-Fiber Line Card Retiming Path MCP3562RT-E/SN ADC for receiver power telemetry يُستخدم في: 3.3 V / 5 V Telecom Transceiver Post-Amplifier Stage, Test and Measurement Pulse Conditioning MCP3426A6-E/SN Microchip Technology يُستخدم في: 3.3 V / 5 V Telecom Transceiver Post-Amplifier Stage MCP6001-I/SN General-purpose op-amp for auxiliary conditioning يُستخدم في: Copper-to-Fiber Line Card Retiming Path MCP3564RT-E/ST Microchip Technology يُستخدم في: Optical Link Loss-of-Signal Detection and Alarm Reporting MCP3426A1-E/MC Microchip Technology يُستخدم في: Test and Measurement Pulse Conditioning
What is the SY88893VKI used for?
The SY88893VKI is a 3.3 V/5 V low-power limiting post amplifier that regenerates a small differential PECL signal to full logic swing at data rates up to 155 Mbps. It is typically placed at the receive end of an optical link, after the photoreceiver, to drive downstream PECL logic, and it also provides a chatter-free TTL signal-detect output plus a TTL enable input. The manufacturer describes the device as a 3.3 V/5 V 155 Mbps PECL low-power limiting post amplifier with TTL signal detect.
What is the difference between a limiting post amplifier and a regular amplifier?
A limiting post amplifier takes a small, degraded differential input, amplifies it, and then amplitude-limits and squares the waveform so it can drive a logic or clock-and-data-recovery stage reliably. A plain linear amplifier does not provide the threshold slicing or the clean, jitter-controlled output edges that a post amplifier is designed for. In the SY88893VKI the limiting behaviour also supports a stable TTL signal-detect output that does not chatter when the input level is marginal.
Which supply voltages does the SY88893VKI support?
The SY88893VKI operates from a single 3.3 V or 5 V supply, as stated in the manufacturer description. The same silicon therefore suits both 3.3 V telecom and 5 V legacy optical module designs, which lets a single qualification cover two module generations. Refer to the manufacturer datasheet for the exact current draw and the allowed supply range limits before fixing the bypass capacitance.
What package does the SY88893VKI come in and how many pins does it have?
The SY88893VKI is supplied in a 10-TFSOP / 10-MSOP package measuring 0.118 in (3.00 mm) in width, a surface-mount footprint with 10 pins. The ordering code suffix in SY88893VKI denotes the industrial temperature grade and tube packaging. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and the exposed pad or ground connections for the package.
What is the TTL signal detect output used for?
The TTL signal-detect output reports whether a usable signal is present at the amplifier input, so the host can distinguish a live link from an unplugged or dark fiber path. In the SY88893VKI this SD output is specified as chatter-free, meaning its state will not oscillate when the input level hovers near the detection threshold. Many system controllers use this signal to mute downstream transmitters, switch to a backup path, or raise an alarm.
Why does the SY88893VKI need a TTL enable input?
The TTL enable input lets the host force the amplifier outputs into a defined, inactive state during reset, power sequencing, or link reconfiguration. This avoids transient outputs on a link that is being brought up or torn down, which is important in pluggable optical modules where several channels are enabled and disabled in an unpredictable order. Because the enable is TTL-compatible, it can be driven directly from the module's existing control logic.
Is the SY88893VKI suitable for SONET/SDH 155 Mbps line cards?
Yes. The SY88893VKI is specified for 155 Mbps operation on a single 3.3 V or 5 V supply with PECL outputs and a TTL signal-detect/enable interface, which matches the classic STM-1/SONET tributary and SDH line-card receive path. Its low-power limiting post-amplifier design is intended for regenerated PECL drive into the CDR or parallel framer. For line rates above 155 Mbps, select a higher-speed post-amplifier family instead.
What is the best drop-in replacement for the SY88893VKI?
The best drop-in replacement is the SY88893VKC, the same Micrel/Microchip 10-MSOP limiting post amplifier in the commercial temperature ordering code, which uses the identical pinout and footprint and can be soldered directly onto a board built for the SY88893VKI. The industrial-grade ordering code SY88893, and the same part in tape-and-reel form, are also drop-in choices. Verify the required temperature grade against your ambient requirements before substituting.
Can the SY88893VKC replace the SY88893VKI on an existing board?
Yes, the SY88893VKC is a drop-in replacement for the SY88893VKI because both are the same 10-MSOP (10-TFSOP) limiting post amplifier with identical PECL I/O, TTL signal detect, and TTL enable functionality. The practical difference is the temperature grade, since the VKI ordering code denotes the industrial grade while the VKC code denotes the commercial grade. Keep the same footprint, the same decoupling layout, and the same differential routing rules when substituting.
When should I choose the SY88893VKI over a general-purpose high-speed amplifier?
Choose the SY88893VKI when the design needs a regenerated, logic-level PECL output with a guaranteed signal-detect function at 155 Mbps. A general-purpose amplifier gives you gain and bandwidth but not the amplitude limiting, the chatter-free TTL signal detect, or the TTL enable input, so you would have to build those functions separately. If your chain only needs small-signal gain into a high-impedance node, a general-purpose part may be simpler.
How should the SY88893VKI input and output be routed on the PCB?
Route the differential input and both PECL output pairs as short, length-matched, tightly coupled traces referenced to a continuous ground plane, and keep the amplifier's supply bypass capacitor at the pins rather than at the power entry point. Avoid long traces and stubs between the amplifier and the downstream logic, because the amplitude-limited edges of the PECL outputs are where ringing and reflection show up first. Follow the reference layout in the manufacturer datasheet for the 10-MSOP footprint.
How much power does the SY88893VKI consume?
The SY88893VKI is described by the manufacturer as a low-power limiting post amplifier operating from a single 3.3 V or 5 V supply. The exact supply current and total dissipation figures are published in the manufacturer datasheet rather than the catalogue pages, and are listed as data needed on this page. Use the datasheet current figures together with your worst-case supply voltage and ambient temperature when sizing the copper area around the 10-MSOP package.
Where can I download the SY88893VKI datasheet PDF?
The SY88893VKI datasheet is published by Microchip Technology, originally by Micrel Semiconductor, and describes the part as a 3.3 V/5 V 155 Mbps PECL low-power limiting post amplifier with TTL signal detect and a TTL enable input. Search the Microchip documentation portal with the base part number SY88893 for the current revision, and use the PDF datasheet for the pin description table, absolute maximum ratings, and supply-current figures that the distributor catalogue pages omit.
What are the key specifications of SY88893VKI that engineers should know?
The core specifications of the SY88893VKI are: 155 Mbps maximum data rate, single 3.3 V or 5 V supply operation, differential PECL outputs, a chatter-free TTL signal-detect output, a TTL enable input, and a 10-TFSOP / 10-MSOP surface-mount package measuring 0.118 in (3.00 mm) wide, supplied in tube packaging. It is a limiting post amplifier intended for optical network receive paths, and it originates from the Micrel Semiconductor product line now owned by Microchip Technology.
Where can I buy SY88893VKI and what is the lead time?
One distributor listing shows approximately 6,000 pieces of the SY88893VKI in stock with the delivery window quoted as a five-day estimated shipment, while most other channels offer the part on a quotation basis. Request current pricing, minimum order quantity, and confirmed lead time through the Request a Quote form on this page, and specify whether you need the tube or tape-and-reel shipping form when placing the order.
Is the SY88893VKI still in production or has it been discontinued?
The SY88893VKI is listed by distributors as an active, orderable Micrel/Microchip product rather than an obsolete or discontinued part, with multiple authorized channel listings and a live stock position. Because the family is mature, it is worth confirming the ordering code, temperature grade, and lifecycle status with the manufacturer for long-term programs. Microchip also offers a part cross-reference search on its own site for competitor equivalents.

بيانات مرجعية هندسية لـ SY88893VKI — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the SY88893VKI when your receive path needs a 155 Mbps PECL signal regenerated from a small differential input, plus a chatter-free TTL signal-detect output and a TTL enable input, and your ambient requirements call for the industrial temperature grade. Choose the SY88893VKC when the same functionality is acceptable in the commercial temperature grade, which is often the lower-cost choice for indoor or room-temperature equipment. Choose the SY88893VKI-TR or SY88893VKC-TR versions when your assembly process runs on tape-and-reel pick-and-place rather than tube-fed lines; the electrical and footprint characteristics are unchanged. If your link rate is above 155 Mbps, or if you need differential outputs beyond PECL levels, move to a higher-speed post-amplifier family instead of pushing this device past its rated rate. Finally, if all you need is small-signal gain into a high-impedance node, a general-purpose amplifier will be simpler, but you will have to build the limiting, signal-detect, and mute functions yourself.

المقارنة مع البدائل

المعامل هذا المنتج SY88893VKC SY88893 SY88893VKI-TR SY88893VKC-TR
Package 10-MSOP (10-TFSOP, 0.118 in / 3.00 mm) 10-MSOP (10-TFSOP) - same 10-MSOP (10-TFSOP) - same 10-MSOP (10-TFSOP) - same 10-MSOP (10-TFSOP) - same
Brand Microchip Technology (Micrel) Microchip Technology (Micrel) Microchip Technology (Micrel) Microchip Technology (Micrel) Microchip Technology (Micrel)
Device Type Limiting post amplifier, low-power Limiting post amplifier, low-power Limiting post amplifier, low-power Limiting post amplifier, low-power Limiting post amplifier, low-power
Maximum Data Rate 155 Mbps 155 Mbps 155 Mbps 155 Mbps 155 Mbps
Supply Voltage 3.3 V or 5 V single supply 3.3 V or 5 V single supply 3.3 V or 5 V single supply 3.3 V or 5 V single supply 3.3 V or 5 V single supply
Signal Detect Output TTL, chatter-free TTL, chatter-free TTL, chatter-free TTL, chatter-free TTL, chatter-free
Enable Input TTL EN input TTL EN input TTL EN input TTL EN input TTL EN input
Output Logic Family PECL differential outputs PECL differential outputs PECL differential outputs PECL differential outputs PECL differential outputs

أبرز الفروقات

  • Integrated chatter-free TTL signal detect removes the need for an external comparator (مقابلGeneric high-speed differential amplifier)
  • One part number covers both 3.3 V and 5 V module platforms (مقابلSY88893VKC)
  • Industrial temperature grade available in the same footprint (مقابلSY88893VKC)
  • 155 Mbps limiting post-amplifier performance with low-power design (مقابلSY88893 base and tape-and-reel ordering codes)

ملاحظات التصميم

Treat the SY88893VKI differential input as a high-speed, low-level signal. Route it as a short, length-matched pair directly from the photoreceiver or line receiver, referenced to a continuous ground plane with no plane splits under the pair. Place the supply bypass capacitor at the device pins and keep it on the same side of the board as the amplifier. PECL outputs should be routed as a tight differential pair into a controlled-impedance or 100 ohm referenced transmission line; long stubs at the output are the most common source of ringing and eye closure in this kind of post-amplifier stage.

The device runs from a single 3.3 V or 5 V supply, so plan the bypass network around that rail and keep the return current path short to the package ground pins. In a 5 V module design, remember that the PECL output swing and the TTL-compatible signal-detect and enable thresholds are referenced to the same supply, so a poorly filtered rail shows up directly as output jitter and as false signal-detect transitions. Use the manufacturer datasheet supply-current figures with the worst-case rail voltage and ambient temperature to size the local copper and the upstream regulator headroom.

Two mistakes recur with this class of device. First, do not substitute a general-purpose high-speed amplifier for a post amplifier: without the amplitude limiting and threshold slicing, noise and intersymbol interference pass straight to the CDR, and the signal-detect function does not exist at all. Second, do not leave the TTL enable input floating or drive it from an incompatible logic level; drive it from the module control logic so the outputs are held in a defined state during reset. Also confirm the temperature grade of the ordering code you fit, since the industrial and commercial versions differ only in grade and in shipping form.

The chatter-free TTL signal-detect output is only meaningful if the amplifier input sees a signal level that is stable enough for the detector to make a consistent decision. Keep the optical or copper input well above the detection threshold in normal operation, and avoid placing the amplifier where its input can pick up crosstalk from the module's transmit side. When validating a new board, check the detect output during link bring-up and during input attenuation sweeps; a detect output that toggles repeatedly usually indicates input level margin problems or return-path coupling, not a defective amplifier.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Yes
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Microchip Technology parts are released as lead-free and RoHS compliant; REACH, halogen-free and conflict-minerals declarations are not stated in the available catalogue information for this part. This device is a telecom/datacom line-card part and is not AEC-Q100 qualified.

تم التحقق من البيانات في: 2026-11-20 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

SY88893VKI datasheet SY88893VKI pinout SY88893VKI datasheet pdf SY88893 limiting post amplifier SY88893VKI 155Mbps PECL amplifier SY88893VKI 10-MSOP package Microchip SY88893VKI SY88893VKI replacement SY88893VKI vs SY88893VKC PECL limiting post amplifier with TTL signal detect SY88893VKI price SY88893VKI stock Micrel SY88893 optical network post amplifier SY88893 TTL enable input signal detect SY88893VKI footprint and layout

المكونات والمصطلحات ذات الصلة

Microchip Technology Micrel Semiconductor SY88893VKI SY88893VKC SY88893 limiting post amplifier post amplifier limiting amplifier line driver transceiver front end optical network PECL ECL TTL signal detect TTL enable input 155 Mbps SONET SDH clock and data recovery 10-MSOP 10-TFSOP surface mount QFN-free MSOP package family RoHS lead-free
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر