NXP Semiconductors

USB2SERA11CFK USB-to-UART Bridge | NXP | 24-HVQFN

MPN: USB2SERA11CFK ✓ نشط
3V or 5V Vdss 40001386 Id 24-HVQFN (5 mm x 5 mm) Package
الحد الأدنى للطلب: 1 |

USB2SERA11CFK نظرة عامة

NXP Semiconductors USB2SERA11CFK is a USB-to-serial bridge integrated circuit implementing a USB 2.0 device interface to a UART interface. The device is specified for 3V or 5V operation and is packaged in a 24-pin HVQFN package measuring 5 mm by 5 mm, with an exposed pad and no-lead terminals. It is intended for industrial-temperature equipment that requires a compact bridge between a USB host connection and a legacy serial interface.

A USB-to-UART bridge is an interface IC that converts USB traffic into a conventional UART data stream. It belongs to the broader USB interface-controller hierarchy, where USB controller and transceiver functions are combined with a serial peripheral interface. This bridge category eliminates the need for a discrete USB controller, transceiver, and UART interface when only one USB-to-serial connection is required.

The USB2SER device is compliant with the USB 2.0 specification and carries USB-IF Test-ID 40001386. Its stated 3V or 5V operation supports both conventional logic levels used in industrial embedded systems. The compact 24-HVQFN footprint reduces board area compared with larger leaded packages, while the exposed thermal pad supports heat transfer into the PCB copper area.

The USB2SERA11CFK is identified as an industrial-grade component and uses a square, no-lead package with 24 terminals. Its principal engineering role is protocol bridging rather than high-speed data conversion. It is therefore most suitable where an external microcontroller or system processor needs an inexpensive, standardized USB-to-UART path for configuration, control, logging, or legacy equipment integration.

Typical applications include industrial control and test equipment, USB-to-serial service adapters, embedded-system commissioning tools, and peripheral controllers with legacy UART connectors. The bridge can simplify enclosure design because a single USB connector and UART interface replace a larger multi-chip USB implementation. Firmware must still implement the required USB enumeration and UART behavior for the target operating system.

PCB design should provide clean USB routing, adequate bypass capacitance at the device supply pins, and a properly connected exposed pad. Follow the manufacturer pin-description and layout guidance when assigning tracks, because the exact pin names, clock requirements, and external component values are not reproduced on this page. Confirm signal levels and supported operating conditions against the manufacturer datasheet before releasing a production design.

This page combines the identified USB 2.0 compliance, 3V or 5V operation, industrial temperature grade, 24-HVQFN package information, and application guidance with sourcing and replacement validation notes. It also highlights the distinction between a verified same-footprint substitute and a merely similar USB interface controller, helping engineers avoid unnecessary PCB redesigns.

بدائل مباشرة لـ USB2SERA11CFK — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

USB2SERA11CFK

✅ بديل مباشر
NXP Semiconductors
📦 24-HVQFN (5x5 mm)
USB-to-UART bridge · USB 2.0 compliant · 40001386 · USB 2.0 · UART · 3V or 5V · Industrial · 24-HVQFN (5 mm x 5 mm)

تواصل لمعرفة السعر

عرض ورقة البيانات ←

USB2SERA11CFK المواصفات

Device Type USB-to-UART bridge
USB Compliance USB 2.0 compliant
USB-IF Test-ID 40001386
Host Interface USB 2.0
Serial Interface UART
Operating Supply 3V or 5V
Temperature Grade Industrial
العلبة 24-HVQFN (5 mm x 5 mm)
Terminal Count 24 terminals
Package Code HVQCCN
Package Shape Square
Terminal Form No lead
Exposed Pad Present
نوع التركيب Surface mount
Shipping Format Tray

دليل تكوين أطراف USB2SERA11CFK square

تكوين الأطراف لـ USB2SERA11CFK (حزمة square). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة square لـ USB2SERA11CFK

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ USB2SERA11CFK.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

USB2SERA11CFK مناسب لـ 6 التطبيقs: Industrial Configuration Interface, USB-to-Serial Service Adapter, Embedded Test and Measurement Equipment, Data Acquisition Controller, Networked Control Gateway, Peripheral Firmware Update Port.

🏭

Industrial Configuration Interface

The USB2SERA11CFK is suitable for an industrial controller that exposes a service configuration port over USB while retaining a UART connection to an embedded processor. Its USB 2.0-compliant device interface and UART bridge function consolidate two communication paths without requiring a larger discrete controller implementation. The 3V or 5V operating options support both common industrial logic environments. Design the system so USB enumeration and configuration descriptors are implemented by the product firmware, and follow the manufacturer land pattern for the 24-HVQFN footprint and exposed pad.

🔧

USB-to-Serial Service Adapter

A compact service adapter can use the USB2SERA11CFK to translate a USB 2.0 host connection into UART signals for a legacy controller. The 24-HVQFN package measures 5 mm by 5 mm, making it useful where adapter PCB area is constrained, while the exposed pad assists thermal transfer into the board. Firmware must present suitable USB descriptors, and the host software must implement the expected serial function. Level translation may still be required when the target UART operates outside the bridge's supported voltage conditions.

🖥️

Embedded Test and Measurement Equipment

The USB2SERA11CFK can connect a host computer to an embedded measurement controller through a standardized USB-to-UART path. This arrangement supports automated setup, calibration commands, diagnostic logging, and firmware updates without exposing a separate proprietary communications connector. Its USB 2.0 compliance and industrial grade suit equipment expected to operate beyond consumer-office environments. The finished product still requires tested USB descriptors, host drivers or a standard virtual serial interface, and a UART protocol designed to handle resets and unexpected reconnections.

📺

Data Acquisition Controller

A compact data-acquisition unit can use the USB2SERA11CFK as the command and configuration path between a PC and a UART-based embedded controller. The bridge allows the acquisition engine to remain focused on measurement functions while USB handles enumeration and cable connectivity. Designers should define a clear command protocol because the serial link may be disconnected or re-enumerated during field service. Validate UART baud-rate tolerance, logic levels, grounding, and cable length in the final system rather than assuming all serial electrical requirements are handled by the bridge.

🌐

Networked Control Gateway

The USB2SERA11CFK can provide a local maintenance channel for a control gateway that otherwise communicates through Ethernet or another fieldbus. Technicians can attach a USB service connection to adjust parameters or retrieve diagnostics while retaining the primary industrial network interface. The compact 24-HVQFN footprint simplifies enclosure design, and 3V or 5V operation allows integration with common control-logic rails. Keep the service interface physically or logically restricted where system security requirements demand controlled maintenance access, and implement firmware authentication independently of the transport bridge.

💾

Peripheral Firmware Update Port

The USB2SERA11CFK can serve as the USB attachment circuit for a peripheral whose main processor receives firmware or configuration data through UART. This approach separates the standard USB connection from the target processor’s serial resources and can simplify firmware-update procedures during manufacturing and field maintenance. A robust design should include power-fail resilience, version negotiation, and signature verification at a higher protocol layer. The USB descriptor implementation and host update utility must agree on the mapping between USB endpoints and the UART byte stream.

What is the USB2SERA11CFK?
The NXP Semiconductors USB2SERA11CFK is a single-chip USB-to-UART bridge that provides a USB 2.0 device connection and a conventional serial interface in one package. According to the manufacturer datasheet, USB2SER is fully compliant with the USB 2.0 specification and has USB-IF Test-ID 40001386. The device is intended to reduce the component count associated with implementing a USB-to-serial connection in industrial embedded equipment.
What package does the USB2SERA11CFK use?
The USB2SERA11CFK uses a 24-HVQFN package measuring 5 mm by 5 mm. Distributor product records identify 24 terminals, a square package shape, no-lead construction, package code HVQCCN, and an exposed pad. The compact surface-mount format supports dense industrial-control and embedded-system layouts, while the exposed pad provides a thermal connection to the PCB. Confirm land-pattern and exposed-pad details against the manufacturer datasheet.
What supply voltage is required for USB2SERA11CFK?
The USB2SERA11CFK is identified as a 3V or 5V USB-to-UART interface IC. The manufacturer documentation confirms support for these two operating-supply options, allowing the bridge to serve both legacy 5V logic systems and designs using a 3.3V rail. Verify the complete recommended operating conditions, supply sequencing, and decoupling configuration in the manufacturer datasheet before using the device at a system boundary.
Is USB2SERA11CFK compliant with USB 2.0?
Yes, the NXP USB2SER is fully compliant with the USB 2.0 specification. The manufacturer datasheet also identifies USB-IF Test-ID 40001386 for the USB2SER device family. This compliance statement applies to the USB behavior implemented by the bridge; the complete product still requires correct hardware implementation, enumeration support, firmware, and host-device interoperability testing in the finished system.
Where can I download the USB2SERA11CFK datasheet PDF?
The USB2SERA11CFK datasheet PDF is linked on this page and describes the NXP USB2SER USB-to-serial bridge. The document covers USB 2.0 compliance, USB-IF Test-ID 40001386, device operation, and application information. Use the manufacturer datasheet as the authoritative source for the complete pin description, timing characteristics, electrical limits, package dimensions, and recommended PCB layout.
Where is the USB2SERA11CFK pinout?
The USB2SERA11CFK pinout is documented in the pin-description section of the manufacturer datasheet. The component has 24 terminals in a 5 mm by 5 mm HVQFN package with an exposed pad. Because individual terminal names and the exposed-pad connection requirements are not reproduced on this page, use the manufacturer pin table and package drawing directly when assigning PCB nets and constructing the footprint.
What can replace the USB2SERA11CFK?
The safest replacement for USB2SERA11CFK is a part with the same 24-HVQFN footprint, the same USB-to-UART function, compatible 3V or 5V operation, and verified pin-for-pin net assignments. No candidate in the identified cross-reference results establishes that combination, so this page does not label an unverified device as a drop-in replacement. Treat another USB bridge as a candidate only after checking its pinout, supply limits, clocking, firmware requirements, and USB descriptors.
Is USB2SERA11CFK the same as a generic USB-to-UART bridge?
No, the USB2SERA11CFK should not be assumed to be interchangeable with a generic USB-to-UART bridge. It combines a USB 2.0-compliant device interface with UART functionality in a 24-HVQFN package and has a defined USB-IF Test-ID of 40001386. A substitute must match the physical footprint, electrical conditions, USB enumeration behavior, and UART signal interface rather than merely providing the same broad function.
What is the best NXP equivalent for USB2SERA11CFK?
No confirmed NXP pin-compatible equivalent to the USB2SERA11CFK appears in the identified cross-reference results. The closest engineering approach is to compare NXP USB-to-UART bridge options by 24-HVQFN footprint, USB 2.0 behavior, 3V or 5V supply operation, UART electrical characteristics, clocking, and exposed-pad requirements. Without a verified net-by-net match, changing the NXP ordering code should be treated as a design review rather than a drop-in substitution.
When should I choose the USB2SERA11CFK?
Choose the USB2SERA11CFK when an industrial embedded product needs a compact USB 2.0 device-to-UART bridge in a 24-HVQFN package. The component is particularly useful when consolidating a discrete USB controller and UART implementation would simplify the PCB. It is less suitable when a design requires a different package, another serial protocol, a host USB role, or a supply condition outside the manufacturer-supported operating range.
Is USB2SERA11CFK suitable for industrial equipment?
The USB2SERA11CFK is identified as an industrial-grade, no-lead USB interface IC. Its USB-to-UART conversion function is useful in industrial control panels, configuration links, service equipment, and embedded test systems. The industrial temperature designation confirms its intended grade, but the exact numeric temperature limits, ESD ratings, isolation provisions, and production test requirements should be confirmed in the manufacturer datasheet.
Where can I buy USB2SERA11CFK online?
The USB2SERA11CFK can be requested through the Request a Quote form on this page, where the required package and order details can be entered for current sourcing review. Current commercial terms, including unit pricing, stock status, and lead time, should be confirmed through that request. This avoids presenting a stale quantity-break figure or implying that a historic listing guarantees immediate availability.
What is the price of USB2SERA11CFK?
Use the Request a Quote form on this page for the current USB2SERA11CFK price, because commercial pricing can vary with order quantity, packaging, market conditions, and sourcing terms. The product is specified as the 24-HVQFN industrial version and must not be confused with other USB2SER ordering codes. The request form is the appropriate channel for a quote tied to the exact MPN and required quantity.
What is the lead time for USB2SERA11CFK?
Request the current USB2SERA11CFK lead time through the Request a Quote form on this page. Lead time depends on the confirmed manufacturer inventory, the 24-HVQFN package, requested quantity, and delivery destination. A dated distributor listing can become stale, so an order-specific confirmation is more reliable than treating an historic stock message as a current delivery commitment.
Is USB2SERA11CFK in stock?
Stock status should be confirmed for the exact USB2SERA11CFK ordering code through the Request a Quote form on this page. The part is the industrial 24-HVQFN version with an exposed pad, so inventory from another package, temperature grade, or USB2SER suffix cannot be substituted for confirmation. A current quote response can provide stock, lead time, and commercial terms for the required quantity.
What are the key specifications of USB2SERA11CFK?
The key USB2SERA11CFK specifications are a USB 2.0-compliant device interface, a UART interface, 3V or 5V operation, an industrial temperature grade, and a 24-HVQFN package measuring 5 mm by 5 mm. The manufacturer datasheet also assigns USB-IF Test-ID 40001386 to the USB2SER device. These characteristics position it as a compact USB interface bridge for industrial embedded equipment.
Does USB2SERA11CFK need firmware for USB enumeration?
The USB2SERA11CFK requires a functioning USB device implementation in the completed product, including the descriptors and class behavior expected by the host. The bridge provides the USB-to-UART hardware interface, while the surrounding system firmware must enumerate the device and manage its serial data path. The manufacturer application information should be used to define the descriptors, connection behavior, and host-side expectations.
How should USB2SERA11CFK be placed on a PCB?
Place the USB2SERA11CFK according to the manufacturer datasheet's land pattern and recommended-layout guidance. The 24-HVQFN footprint is small and leadless, so the exposed pad and surrounding ground or supply copper must follow the prescribed connection scheme. USB differential routing should remain short and symmetrical, bypass connections should be placed close to their associated supply pins, and the pad must be thermally coupled through the PCB stack-up.

بيانات مرجعية هندسية لـ USB2SERA11CFK — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the USB2SERA11CFK when the design needs a compact, industrial-grade USB 2.0 device-to-UART bridge in the 24-HVQFN package and the system uses 3V or 5V operation. It is a strong fit for service ports, embedded test equipment, configuration links, and manufacturing firmware-update fixtures. Before choosing a replacement, require the same package, exposed-pad arrangement, pin-to-pin assignments, USB device behavior, UART electrical characteristics, and clocking scheme; functional similarity alone is insufficient. A different package or pin map requires a PCB revision even if the replacement performs the same protocol conversion. Use the manufacturer datasheet to decide whether the bridge supports the required baud rates, UART signal levels, host driver model, and environmental operating conditions.

أبرز الفروقات

  • Integrated USB 2.0 and UART interface (مقابلGeneric USB-to-UART bridge)
  • USB compliance identifier (مقابلNon-qualified USB interface controller)
  • Compact leadless package (مقابلLarger leaded USB interface package)
  • Industrial product grade (مقابلConsumer-grade USB bridge)

ملاحظات التصميم

Construct the USB2SERA11CFK footprint from the manufacturer package drawing and pin table rather than relying on a generic 24-QFN land pattern. Confirm the exposed-pad dimensions, pin-1 orientation, pad numbering, solder-mask clearance, and paste pattern. The package is only 5 mm by 5 mm and has no leads, so even a small pin-number or rotation error can prevent reliable assembly.

Route the USB interface as a controlled-impedance differential pair and keep it short, continuous, and away from noisy switching nodes. Place the USB connector, protection components, and bridge in the same signal path with minimal stubs. Apply the manufacturer reference layout when possible, because connector placement and board-stack-up can materially affect USB 2.0 signal integrity even when the IC itself is correctly placed.

Do not assume that every USB-to-UART bridge can replace the USB2SERA11CFK. Before substituting a part, compare USB device role, supply voltage, UART logic levels, clock requirements, descriptor support, exposed-pad connections, and every numbered pin. Functionally similar controllers can use different internal clocks or map connector signals to different pins, so a schematic-level match must be confirmed before PCB reuse.

Use the exposed pad as part of the thermal design. Follow the manufacturer datasheet for its electrical connection and recommended copper area, then provide uninterrupted PCB copper beneath the package where the recommended pattern permits. Estimated thermal performance depends on the PCB area, copper thickness, board stack-up, ambient temperature, and enclosure airflow, so validate the final assembly thermally rather than relying on package size alone.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer datasheet confirms USB 2.0 compliance and USB-IF Test-ID 40001386. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code.

تم التحقق من البيانات في: 2026-11-10 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

USB2SERA11CFK datasheet USB2SERA11CFK pinout USB2SERA11CFK datasheet pdf USB2SERA11CFK equivalent USB2SERA11CFK replacement USB2SERA11CFK price USB2SERA11CFK stock NXP USB2SERA11CFK USB2SERA11CFK footprint USB2SERA11CFK application circuit

المكونات والمصطلحات ذات الصلة

NXP Semiconductors USB2SERA11CFK USB2SER USB-to-UART bridge USB interface controller UART interface USB 2.0 USB-IF Test-ID 40001386 industrial-grade semiconductor 24-HVQFN HVQCCN 5 mm by 5 mm package exposed pad no-lead surface-mount package 3V operation 5V operation USB enumeration embedded systems industrial control equipment service configuration port data acquisition controller firmware update interface UART protocol surface mount
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر