উপশ্রেণী

পণ্য (44,000+)

VSC7224XJV - 12.5Gbps 4-Channel CDR Retimer | Microchip
VSC7224XJV

VSC7224XJV - 12.5Gbps 4-Channel CDR Retimer | Microchip

The Microchip VSC7224XJV is a four-channel unidirectional adaptive channel extender with clock and data recovery, rated up to 12.5 Gbps and housed in a 48-QFN package measuring 5 mm by 9 mm. It combines analog equalization, digital equalization, clock and data recovery, and configurable output de-emphasis in one signal-conditioning device. The four-channel architecture allows one device to condition four independent serial links while supporting copper cable, backplane, and other lossy interconnect applications. A retimer with clock and data recovery is a specialized interface IC that receives a high-speed serial signal, recovers its transmitted clock and data, applies programmable equalization, and reserializes the conditioned data. Within the interface-IC hierarchy, the VSC7224 belongs to the retimer and redriver class. Unlike a simple redriver, which amplifies and reshapes an existing signal, a retimer can regenerate the signal through a CDR stage, improving interoperability across lossy channels. The VSC7224 family supports multiple rate grades. Manufacturer information identifies operation up to 10.3 Gbps, 11.5 Gbps, or 12.5 Gbps depending on the selected product variant. The VSC7224XJV is listed as a four-channel 12.5 Gbps retimer/redriver, while the VSC7224XJV-01 is identified as an 11.5 Gbps variant. Analog and digital equalization provide compensation for frequency-dependent loss, and output de-emphasis helps control edge amplitude and reduce signal-integrity problems on longer channels. The 48-QFN package consolidates four channels into a compact footprint suitable for telecommunications equipment, data-processing systems, and high-speed backplane links. Because the device performs CDR rather than only analog amplification, it is particularly useful when transmitter and receiver clocking cannot tolerate accumulated deterministic jitter or signal degradation. Designers must still preserve controlled impedance, provide adequate power and ground connectivity, and verify the configuration for the target data rate and channel loss. Typical uses include 10G/25G-class serial links, telecommunications backplanes, server and networking equipment, and cable or copper interconnects. The VSC7224 is most appropriate when each link requires independent equalization and clock recovery rather than simple gain compensation. Its four-channel organization can also reduce board-area requirements compared with implementing four separate single-channel signal-conditioning devices. Layout quality is critical in multirate retimer designs. Place input and output bypass capacitors close to their associated supply pins, maintain continuous ground-plane return paths, and route high-speed differential pairs as short, impedance-controlled transmission lines. Avoid adding test pads or long branch stubs on sensitive channels, because parasitic capacitance and inductance can degrade eye opening even when the equalizer is correctly configured. This page consolidates the manufacturer’s device architecture, exact variant distinctions, sourcing information, and application-specific engineering guidance. It also distinguishes the 12.5 Gbps VSC7224XJV from the 11.5 Gbps VSC7224XJV-01, helping designers select the correct speed grade and plan a repeatable high-speed layout.

RFQ যোগাযোগ
VSC7226UI-06 - Quad-Channel Transceiver | Microchip
VSC7226UI-06

VSC7226UI-06 - Quad-Channel Transceiver | Microchip

The Microchip Technology VSC7226UI-06 is a quad-channel interface controller and parallel-to-serial/serial-to-parallel transceiver designed for high-bandwidth data transmission between buses, backplanes, and other subsystems. It provides 4 communication channels and is supplied as an interface IC in the VSC7226 product family. An interface transceiver is a semiconductor device that converts data between parallel and serial formats while supporting reliable signal transfer over board-level communication paths. Within the hierarchy of interface ICs, parallel-to-serial and serial-to-parallel converters provide the physical data-rate adaptation needed by communication equipment, and they sit between general-purpose processors and higher-speed physical links. Their primary design goals are efficient data handling, predictable signal integrity, and reliable operation in infrastructure and industrial systems. The VSC7226 family combines four conversion channels in one device, reducing the number of separate interface devices required in a multi-lane subsystem. The VSC7226UI-06 ordering code identifies a specific member of the Microchip Technology product family, while the base VSC7226 description identifies the device as a quad-channel parallel-to-serial and serial-to-parallel transceiver. This architecture is intended for backplanes and other subsystems that require efficient movement of multiple data streams. From an implementation perspective, the device belongs to the interface-controller portion of a communication system rather than the processor or physical-transceiver portion. Its four channels allow a designer to organize related high-speed links through a common controller. This can simplify board partitioning and provide a consistent interface between parallel subsystem logic and serial communication paths. Exact operating conditions, lane rates, electrical levels, timing limits, and channel configuration must be selected from the manufacturer datasheet before final circuit design. Typical application areas include network equipment, industrial infrastructure, and other systems that move data between buses, backplanes, and connected subsystems. The 4-channel architecture is particularly relevant when four related parallel-to-serial or serial-to-parallel paths are required. Engineers should verify the exact pin assignment, power requirements, interface protocol, and signal-integrity constraints against the VSC7226 family documentation before laying out a PCB. A key design consideration is that ordering suffix variations can represent different grade or configuration options while retaining the same family architecture. Confirm the exact VSC7226UI-06 datasheet and package information rather than treating an undated secondary PDF as the controlling document. This page distinguishes documented product functions from electrical details that require direct manufacturer confirmation. This page combines the verified product identity, interface-controller role, four-channel architecture, source links, practical application guidance, and a structured comparison with related VSC7226 ordering options. It also highlights where engineers must verify package, pinout, timing, and lifecycle details before committing a design to production.

RFQ যোগাযোগ
VSC7323VH - 10G Ethernet MAC Controller | Microchip
VSC7323VH

VSC7323VH - 10G Ethernet MAC Controller | Microchip

The Microchip Technology VSC7323VH is a 10G Ethernet MAC controller with support for ten 1G Ethernet interfaces, implemented in 0.18-micron CMOS technology and supplied in a 728-pin TBGA package measuring 42.5 mm by 42.5 mm. The device accepts 2.5 V and 3.3 V I/O supplies, supports an industrial temperature range extending to +85 °C, and includes a standard five-pin P1149.1 JTAG test port. An Ethernet MAC controller is an interface IC that manages communication between a host or switching subsystem and physical Ethernet interfaces. Within the semiconductor hierarchy, it belongs to the Ethernet interface-controller class, which sits under network interface ICs and broader communication semiconductors. The VSC7323VH is intended for demanding systems that require a consolidated 10G MAC function alongside multiple 1G Ethernet connections. Key features include ten integrated 1G Ethernet MAC positions, one 10G Ethernet MAC function, a 2.5 V or 3.3 V I/O operating range, and an industrial temperature rating to +85 °C. Its 0.18-micron CMOS implementation reflects the process technology used for this generation of high-integration networking silicon. The five-pin JTAG interface supports boundary-scan-oriented manufacturing and test access. The 728-pin TBGA package provides extensive high-speed connectivity for parallel or otherwise complex networking interfaces. Its 42.5 mm by 42.5 mm body is substantially larger than common QFN and QFP packages, reflecting the high pin count and routing demands of the device. Board design must consequently address dense escape routing, controlled-impedance links, via arrays, return-path continuity, and power-distribution integrity. Typical applications include enterprise and metro Ethernet switching platforms, multi-service provisioning equipment, industrial networking systems, and telecommunications access products. The combination of ten 1G and one 10G MAC channel can reduce the number of discrete interface devices required in a line-card or switching subsystem while retaining dedicated test access through JTAG. Designers should verify the original Vitesse Semiconductor datasheet, signal-integrity requirements, pin assignment, and power sequencing before layout. Because this 728-pin TBGA has a large ball array, manufacturing capability, via-in-pad suitability, thermal management, and X-ray inspection requirements should be confirmed with the PCB assembler. Commercial availability and pricing are quote-based in the supplied market data. This page consolidates verified distributor listings, the available VSC7323 datasheet information, package constraints, procurement details, and a qualified drop-in comparison. It also separates confirmed specifications from unavailable electrical parameters, helping engineers evaluate the VSC7323VH without mistaking unsupported values for manufacturer guarantees.

RFQ যোগাযোগ
VSC7385XYV - 5-Port Gigabit Ethernet Switch + PHY | Microchip
VSC7385XYV

VSC7385XYV - 5-Port Gigabit Ethernet Switch + PHY | Microchip

The Microchip Technology VSC7385XYV is a five-port Gigabit Ethernet switch with integrated physical layer, or PHY, devices in a surface-mount package. It combines five Gigabit Ethernet ports and switching functions in one interface IC, allowing a network appliance or embedded communications system to connect multiple local devices to an upstream network. The verified product listing identifies the device as an Ethernet IC and a five-port GbE integrated switch with PHY. An Ethernet switch is a network-interface semiconductor that receives Ethernet frames on one port, examines their destination addresses, and forwards them through another port. A PHY supplies the physical signaling interface between the switch logic and twisted-pair or other physical network media. Integrating the PHYs with the switching engine reduces the number of separate Ethernet components required in a compact network endpoint, industrial controller, access point, or embedded gateway. The verified listings identify the VSC7385XYV as an active, surface-mount device. No verified package designation, pin count, operating-voltage range, maximum data rate value, clock configuration, thermal rating, or AEC-Q100 status was supplied in the source data. Those attributes remain designated as data-needed rather than being inferred from the product family or from unrelated Ethernet components. The VSC7385XYV is best suited to five-port Gigabit Ethernet aggregation, embedded network bridging, industrial communication gateways, and equipment that needs multiple Ethernet connections in one subsystem. Its integrated switch-and-PHY architecture can simplify board partitioning compared with a design using discrete switch and PHY devices. Final interface selection still depends on the exact package, supported copper media, electrical limits, firmware requirements, and reference configuration in the manufacturer documentation. Engineers should begin with the manufacturer datasheet and confirm the land pattern, pin multiplexing, supply rails, clocking, LED or status signaling, and reference schematic before layout. The alternate vendor listing names the part as an Ethernet controller and the distributor listing categorizes it as a switch IC. These classifications are consistent with the five-port Gigabit Ethernet switch-plus-PHY description. The principal design trade-off is integration versus flexibility. Consolidating switch and PHY functions can reduce component count and board area, but a tightly integrated part can be less forgiving of unusual media, connector, timing, or thermal requirements than a modular design. Validate magnetics, termination, layout, power sequencing, and environmental requirements on the final platform. This page consolidates the verified distributor identity, availability indications, product classification, packaging information, and substitute-search results for VSC7385XYV. It also distinguishes confirmed facts from missing datasheet parameters and avoids presenting unverified pin assignments, pricing, or cross-brand replacements as engineering facts.

RFQ যোগাযোগ
VSC7389XHO - 16-Port GbE Switch with 8 PHYs | Microchip
VSC7389XHO

VSC7389XHO - 16-Port GbE Switch with 8 PHYs | Microchip

The Microchip Technology VSC7389XHO is a 16-port Gigabit Ethernet switch with eight integrated PHYs, supplied in a 596-ball BGA package measuring 35 mm by 35 mm. It is categorized by distributors as a special-purpose telecommunications switch IC and combines Ethernet switching functionality with eight physical-layer interfaces in one high-pin-count package. The available distributor information identifies Microchip Technology as the manufacturer and confirms the 16-port Gigabit Ethernet architecture, eight PHY integration, 596-BGA construction, and 35 mm by 35 mm package dimensions. An Ethernet switch is a network-semiconductor device that receives Ethernet frames at multiple physical ports, examines frame destination information, and forwards traffic toward the appropriate output port. In the networking hierarchy, this VSC7389XHO belongs to Ethernet switch ICs, interface ICs, and ultimately integrated semiconductors. Its eight integrated PHYs connect copper Ethernet links to the switching fabric, while the remaining switch ports support network-facing connections configured through the broader telecommunications switching system. The three headline characteristics of the VSC7389XHO are its 16 Gigabit Ethernet ports, eight integrated PHYs, and 596-ball BGA package. Integrating eight PHYs can reduce the number of external physical-layer devices required in a multiport design. The large BGA also provides the pin density needed for a complex switching solution, although its 596 balls and 35 mm by 35 mm outline make PCB layout, assembly, inspection, and thermal management substantially more demanding than those for a small leaded or low-pin-count package. Because the supplied search results do not expose the complete Microchip datasheet, switching throughput, latency, supported media types, clocking, management interfaces, power specifications, or operating-temperature limits, those values should not be inferred from the distributor category. The 596-ball package should be treated as a land-grid-array device with a dense peripheral fanout. Component classification as a “special purpose” analog switch reflects distributor taxonomy and does not establish that the device is a simple analog multiplexer; the manufacturer description identifies it as a 16-port Gigabit Ethernet switch with eight PHYs. Typical design uses include industrial Ethernet aggregation, telecommunications access equipment, embedded network infrastructure, and multiport copper-network systems. In such systems, the eight integrated PHYs can serve direct copper links, while a larger switch configuration may use additional external interfaces. Final suitability depends on protocol support, media capability, management features, timing, power, and thermal requirements that are not exposed in the verified distributor snippets. The primary engineering consideration is the 596-ball BGA assembly. A valid replacement must match the land pattern, ball assignment, electrical performance, firmware expectations, and thermal requirements; merely using the same 35 mm by 35 mm outline is insufficient. Before layout release, engineers should obtain the manufacturer datasheet, pinout, reference design, recommended decoupling network, PCB stack-up, and assembly process information, then validate the complete Ethernet design for signal integrity and thermal performance. This page consolidates the verified distributor identity, package information, port and PHY counts, sourcing links, comparison parameters, and practical replacement criteria for VSC7389XHO. Because no verified pin-compatible substitutes or numeric price tiers were provided, the record explicitly preserves those uncertainties instead of presenting generic same-category parts as drop-in replacements.

RFQ যোগাযোগ
VSC7390XHO - 24-Port Gigabit Ethernet Switch | Microchip
VSC7390XHO

VSC7390XHO - 24-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7390XHO is a 24-port integrated Layer-2 Gigabit Ethernet smart switch with integrated copper transceivers, supplied in a 596-BGA package measuring 35 mm by 35 mm. The device provides four Gigabit Ethernet ports and 48 integrated tri-speed copper transceivers supporting 10/100/1000 Mbps operation. Its IEEE 802.3ab-compliant Gigabit Ethernet PHYs make it suitable for systems that require local switching, copper media access, and integrated network-interface functionality in one package. A smart Ethernet switch is an interface IC that connects multiple network nodes and forwards Ethernet frames according to Layer-2 addresses. Within the device hierarchy, this product belongs to Ethernet controllers, network interface controllers, interface ICs, and integrated circuits. Integrating switching and physical-layer circuitry can reduce the number of separate PHY components required in a network appliance, although the complete design still requires adequate board area, thermal management, signal-integrity control, and verified magnetic-interface components. The principal verified features of the VSC7390XHO are its 24-port Layer-2 switching architecture, four Gigabit Ethernet ports, 48 integrated tri-speed copper transceivers, and support for 10/100/1000 Mbps data rates. The integrated PHYs are identified as IEEE 802.3ab compliant, providing a defined Gigabit Ethernet copper-interface basis for the system. The package also provides a high pin count and substantial contact area, making careful layout, grounding, and power-plane design important in a production layout. The product is specified as lead-free and RoHS compliant. Its manufacturer product page identifies the VSC7390 family as “Not Recommended for new designs,” making lifecycle status an important qualification criterion. This designation does not mean that every existing design must be replaced immediately, but new equipment should normally use a currently recommended switching platform unless an approved lifecycle program specifically supports the older family. Typical uses for this device include managed network appliances, industrial Ethernet equipment, telecommunications access hardware, storage systems, surveillance infrastructure, and other embedded systems requiring multiple copper Ethernet connections. Its integration can simplify board partitioning when the required channel count and physical-layer configuration match the target network architecture. It is less suitable when a design requires a different number of ports, a different copper-media standard, or a currently recommended lifecycle pathway. Before committing a layout, engineers should confirm the complete VSC7390 pin and ball assignment from the manufacturer documentation, validate power and thermal requirements, and preserve high-speed copper-channel geometry. The verified data does not provide a complete public ball map, so this page does not fabricate pin assignments or claim a specific reference design. Production procurement should also confirm package marking, die revision, lifecycle obligations, and manufacturer-approved sourcing. This page consolidates the verified manufacturer status, distributor listings, package information, and RoHS and lead-free statements. It also distinguishes the VSC7390XHO from generic Ethernet-switch families and explicitly avoids presenting cross-package functional substitutes as pin-compatible drop-in replacements.

RFQ যোগাযোগ
VSC7395XYV - 5+1 Gigabit Ethernet Switch | Microchip
VSC7395XYV

VSC7395XYV - 5+1 Gigabit Ethernet Switch | Microchip

Microchip Technology VSC7395XYV is an integrated 5+1-port Gigabit Ethernet switch with five tri-speed copper PHYs, one RGMII/GMII interface, nonblocking wire-speed switching, and a 364-BGA (23x23) package. It operates from a single 3.3 V supply and provides five IEEE 802.3ab-compliant 10/100/1000 Mbps copper ports. An integrated Gigabit Ethernet switch is a network-interface IC that combines multiple Ethernet physical-layer transceivers, frame-processing logic, and a switching fabric in one device. Within the product hierarchy, it is an Ethernet switch, network interface IC, communications semiconductor, and power-management-dependent mixed-signal component designed for telecommunications and embedded networking equipment. The principal features include five integrated copper transceivers, one RGMII/GMII tri-speed port, support for 10, 100, and 1000 Mbps operation, nonblocking wire-speed performance, and a single 3.3 V supply. The copper interfaces are identified as IEEE 802.3ab compliant. Its 364-BGA package provides a high pin count suitable for parallel data, clock, control, power, and ground connectivity. Technically, the device consolidates multiple PHY channels and switch resources on one silicon die, reducing the number of separate Ethernet components required in a multiport design. The RGMII/GMII port provides a flexible processor- or switch-facing uplink when the five copper ports are used for downstream connections. Exact clocking, latency, MAC-table, management-interface, and power-consumption details require confirmation in the manufacturer documentation and were not present in the supplied excerpts. Typical applications include industrial Ethernet gateways, telecommunications access equipment, embedded routers, network-interface controllers, and managed switching products. Its five copper PHYs suit equipment that must connect several wired endpoints while retaining a high-speed uplink through RGMII or GMII. The obsolete lifecycle status means new designs should confirm availability, lifecycle options, or a supported successor with Microchip before committing to the part. Designers should pay particular attention to the 364-BGA escape routing, high-speed RGMII/GMII signal integrity, power-plane integrity, and thermal performance. Because the VSC7395XYV is listed as end-of-life and obsolete by verified sources, board revisions should preserve the footprint and power architecture when long-term maintenance is required. This page consolidates the verified port, speed, voltage, package, lifecycle, and environmental information with same-family replacement context and practical design guidance. It also clearly identifies parameter gaps, avoiding unsupported claims about latency, management features, pricing, or full pin-level connectivity.

RFQ যোগাযোগ
VSC7395XYV-03 5+1-Port Gigabit Ethernet Switch | Microchip
VSC7395XYV-03

VSC7395XYV-03 5+1-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7395XYV-03 is a 5+1-port Gigabit Ethernet switch with integrated transceivers, five tri-speed 10/100/1000 Mbps copper ports, and one additional tri-speed RGMII/GMII interface, housed in a 364-BGA package measuring 23 x 23 mm. It provides nonblocking wire-speed switching for telecommunications, industrial networking, and embedded Ethernet systems. An Ethernet switch is a networking semiconductor that receives Ethernet frames on one or more ports and forwards them toward their destination ports using hardware address information. The VSC7395XYV-03 belongs to the Ethernet switch IC category, which sits within interface ICs, semiconductor networking components, and broader data-communication systems. Its integrated copper transceivers reduce the need for separate PHY devices when each copper link remains within its supported electrical and distance requirements. The principal feature is the combination of five integrated tri-speed copper transceivers and one additional tri-speed RGMII/GMII interface. Each copper transceiver supports 10, 100, and 1000 Mbps operation and is identified as IEEE 802.3ab compliant in the manufacturer documentation. Nonblocking wire-speed performance allows each supported port to process traffic at its negotiated line rate without a central throughput bottleneck, provided the aggregate traffic remains within the switch fabric's design limits. The mixed-signal architecture combines digital frame switching with analog copper transceiver functions. This integration can simplify a multilayer board by consolidating PHY and switch functionality, but it also places demanding signal-integrity, power-supply, thermal, and layout requirements on the implementation. Differential Ethernet pairs, reference clocks, reset or control signals, and power rails must be routed according to the manufacturer layout guidance. Controlled impedance and short return paths are particularly important around the 364-pin BGA device. Typical applications include enterprise and industrial Ethernet switching, telecommunications access equipment, network-interface aggregation, industrial control networks, and embedded systems that need several copper links plus a processor-facing RGMII or GMII connection. The RGMII/GMII port can provide a high-speed parallel interface to a host processor or another switching element, while the integrated copper ports handle endpoint connectivity. The primary design consideration is that VSC7395XYV-03 is a complex mixed-signal BGA component rather than a simple low-pin-count Ethernet PHY. Power sequencing, clock integrity, decoupling, magnetics or cable qualification, thermal management, and high-speed differential routing must be planned together. Review the manufacturer datasheet and reference design before freezing the PCB layout. This page organizes the confirmed port, speed, protocol, package, and compliance characteristics of VSC7395XYV-03 and separates them from parameters that require a datasheet-specific engineering review. It also provides application guidance, comparison fields, and design notes to help engineers assess whether this highly integrated Ethernet switch suits a new board design or a constrained legacy redesign.

RFQ যোগাযোগ
VSC7398XYU - 8-Port Gigabit Ethernet Switch | Microchip
VSC7398XYU

VSC7398XYU - 8-Port Gigabit Ethernet Switch | Microchip

Microchip Technology VSC7398XYU is an 8-port Gigabit Ethernet switch with integrated PHYs, providing eight tri-speed 10/100/1000 Mbps copper Ethernet ports in a 757-BGA (40x40 mm) package. The device is based on the SparX-G8e enhanced Gigabit Ethernet switching architecture and supports nonblocking wire-speed switching across eight ports. Its copper transceivers are IEEE 802.3ab compliant, allowing the switch to support Gigabit Ethernet links without requiring separate external PHY devices for each copper port. An Ethernet switch is a networking semiconductor that connects multiple Ethernet endpoints through a shared switching fabric. It inspects incoming Ethernet frames and forwards traffic toward the appropriate destination port, while also handling other Layer 2 functions implemented by the device. The VSC7398XYU sits in the hierarchy of Ethernet interface integrated circuits, network switches, interface ICs, semiconductors, and embedded networking equipment. Integrating the switch function and physical-layer transceivers into one device simplifies hardware design in gateways, industrial controllers, access equipment, and embedded network systems. The principal verified features are the eight integrated Gigabit Ethernet ports, support for 10, 100, and 1000 Mbps operation, nonblocking wire-speed performance, and IEEE 802.3ab-compliant copper transceivers. All eight ports support copper connectivity through integrated PHYs. This integration reduces the number of separate network interface devices required when several Ethernet connections must terminate on one circuit board. The exact switching fabric throughput, latency, SRAM organization, voltage ratings, and management-interface details are not included in the supplied verified data and therefore require confirmation from the manufacturer datasheet. The SparX-G8e implementation consolidates switching and transceiver functions within a single highly integrated mixed-signal network IC. This architecture is appropriate for equipment requiring multiple Ethernet ports but limited board space, such as compact access points, industrial communication controllers, and embedded gateways. Because the copper PHYs are integrated, board-level design must account for the device's thermal behavior, high-speed differential routing, magnetics or coupling requirements, controlled impedance, and layout practices specified by Microchip. The supplied data does not provide the complete reference design or pin-level electrical constraints, so those details should be obtained from the official documentation before schematic capture. Typical applications include eight-port industrial Ethernet switching, embedded control and test systems, telecom access equipment, industrial automation gateways, network appliances, and compact embedded communication platforms. The eight-port configuration is particularly useful when a system must connect controllers, sensors, service equipment, and supervisory computers through isolated Ethernet interfaces. Using a nonblocking, wire-speed switch allows traffic to be aggregated while avoiding the component count of eight standalone Ethernet interface devices. Designers should obtain the official VSC7398 product brief, datasheet, CAD models, and reference schematic before committing the 757-BGA footprint. The supplied distributor information identifies the package as 757-BGA (40x40), but no verified pinout, power-supply values, maximum copper-cable length, operating-temperature range, or recommended magnetics data were provided. Those parameters must be verified rather than inferred because the Ethernet PHYs, supply rails, clocking, and high-speed copper interfaces determine whether a particular board design will meet system requirements. This page consolidates the verified manufacturer and distributor findings for the VSC7398XYU, explicitly distinguishes confirmed specifications from missing data, and records the product's NRND status. It also provides engineering-focused application guidance and a source-traceable comparison framework. No unsupported drop-in alternatives, package substitutions, pricing values, pin assignments, or unverified performance claims are presented.

RFQ যোগাযোগ
VSC7410XMT - 6-Port Enterprise Ethernet Switch | Microchip
VSC7410XMT

VSC7410XMT - 6-Port Enterprise Ethernet Switch | Microchip

The Microchip Technology VSC7410XMT is a six-port enterprise Ethernet switch with two integrated copper PHYs, IEEE 1588v2 support, and a 324-ball PBGA package measuring 19 mm by 19 mm. It operates from a 0.95 V to 1.05 V core supply and draws approximately 1.3 A, making it a high-density switching solution for telecommunications, industrial, and enterprise networking equipment. An Ethernet switch is a semiconductor that forwards Ethernet frames between multiple network ports using hardware-based address lookup. It belongs to the network-interface hierarchy that includes Ethernet transceivers, network controllers, and interface ICs. By integrating switch functions and copper PHY resources on one device, the VSC7410XMT reduces the number of discrete components needed for a multiport networking platform while supporting precise timing applications. The principal features include six configurable switch ports, two integrated copper PHYs, and a core operating range of 0.95 V to 1.05 V. IEEE 1588v2 capability is especially relevant to synchronized networks, while the operating-temperature range of -40°C to 125°C supports industrial and telecommunications equipment. The device also provides a two-wire serial interface and JTAG for configuration, diagnostics, and board-level control. The VSC7410XMT is part of Microchip's Serval-T switch family and is positioned for market-ready enterprise-switch designs. Its 324-PBGA package concentrates substantial connectivity and switching resources into a 19 mm by 19 mm surface-mount footprint. Because the package contains many balls and requires controlled power and signal integrity, PCB layout should follow the manufacturer's pin assignment, reference-layout, and decoupling guidance exactly. Typical uses include enterprise Ethernet switching, telecommunications aggregation, industrial Ethernet equipment, and time-sensitive networked systems. The two integrated copper PHYs are useful where the board includes direct copper connections, while the remaining switch ports support broader network-interface configurations when paired with suitable external PHY or serializer resources. Power-system design is a critical implementation consideration because the specified 1.3 A current draw must be evaluated alongside the 0.95 V to 1.05 V supply range. Provide the required core and I/O supplies with low-impedance decoupling, and validate sequencing, thermal performance, and signal integrity on the final multilayer PCB before production release. This product page combines the manufacturer's device description with practical guidance on supply requirements, package handling, Ethernet applications, and qualification. Because the 324-ball assignment is complex and no verified pin table accompanies the available technical material, use the manufacturer datasheet for final ball mapping, electrical limits, and layout implementation.

RFQ যোগাযোগ
VSC7415XMT 6-Port Enterprise Switch | Microchip Technology
VSC7415XMT

VSC7415XMT 6-Port Enterprise Switch | Microchip Technology

The Microchip Technology VSC7415XMT is a Serval-T enterprise Ethernet switch IC with 6 ports and 2 integrated copper PHYs, supplied in a 324-BGA package measuring 19 x 19 mm. It is positioned as a high-performance, market-ready switching solution for IEEE 1588v2 synchronization applications. The integrated copper PHY capability reduces the amount of external copper transceiver circuitry required in enterprise networking equipment. An Ethernet switch IC is a semiconductor device that connects multiple network endpoints through integrated physical-layer and switching functions. It sits above the physical layer in the network hierarchy: copper PHY interfaces connect physical media, while the switch fabric forwards Ethernet traffic between ports. Enterprise switches use this integration to reduce board area, simplify signal routing, and support synchronization-sensitive infrastructure equipment. The VSC7415XMT's principal documented features are its 6-port configuration, 2 integrated Cu PHYs, Serval-T switch-family positioning, and support for IEEE 1588v2. The 19 x 19 mm, 324-ball BGA package provides a high pin count suitable for a complex multiport networking device, although its fine pitch requires careful PCB layout, inspection, and assembly controls. The device is suited to enterprise Ethernet switching, telecommunications access equipment, industrial network infrastructure, and other Ethernet systems where a compact multiport switching solution is valuable. Its integrated copper PHYs are especially relevant when the design requires direct copper-media connectivity without adding discrete PHY components alongside the switch controller. IEEE 1588v2 capability makes the VSC7415XMT relevant to systems requiring precise network timing and synchronization. Clock, power, signal-integrity, and thermal design must be evaluated together because high-speed BGA routing, PHY requirements, and synchronization accuracy can constrain the surrounding power-delivery network and board stack-up. This page combines the manufacturer product-page information, distributor listings, package identification, transaction guidance, and engineering selection considerations for engineers evaluating the VSC7415XMT. Before committing a layout, obtain the complete manufacturer datasheet and verify every pin, supply rail, interface requirement, and layout rule against the exact ordering code.

RFQ যোগাযোগ
VSC7416XKT-01 - 6-Port Carrier Ethernet Switch | Microchip
VSC7416XKT-01

VSC7416XKT-01 - 6-Port Carrier Ethernet Switch | Microchip

Microchip Technology VSC7416XKT-01 is a six-port Carrier Ethernet switch supporting 10 Mbps, 100 Mbps, and 1 Gbps Ethernet links in a 284-lead TQFP package measuring 24 x 24 mm. It is designed for telecommunications infrastructure equipment that requires multiple copper Ethernet ports, Layer-2 switching, and carrier-grade network functionality. The manufacturer lists the VSC7416 family as End of Life, so engineers should confirm availability and migration requirements before starting a new design. A Carrier Ethernet switch is a specialized Ethernet interface integrated into access, aggregation, and transport equipment. Unlike a general-purpose desktop Ethernet switch, a carrier-grade device is selected for telecommunications packaging, port density, network-management requirements, and compatibility with service-provider transport functions. Within the equipment hierarchy, the VSC7416XKT-01 sits between Line Cards and carrier Ethernet ports, converting electrical network traffic into a multiport switching resource for telecommunications systems. The primary feature set includes six ports, 10/100/1000-Mbps operation, and a 284-pin TQFP package. Its high pin count supports the extensive connections required by a carrier Ethernet switching function, including network interfaces, control, power, configuration, and support circuitry. Because the package is physically large, designers must preserve adequate copper area and follow the manufacturer's land pattern and thermal recommendations during PCB layout. This component belongs to Microchip's VSC7416 product family, identified on the manufacturer page as a six-port Carrier Ethernet switch. The related documentation search identifies the family as a Layer-2 Carrier Ethernet platform with MPLS/MPLS-TP support and VeriTime. These functions place the device at the network-forwarding layer, where traffic is handled according to Layer-2 information rather than being treated as a simple physical interface. The exact enabled feature set for each board design should be checked against the applicable configuration and software documentation. Typical uses include telecommunications line cards, access-node equipment, Ethernet aggregation systems, industrial network gateways, and carrier Ethernet test equipment. The six-port arrangement can reduce the number of discrete switching devices required on a board while supporting a mix of 10-Mbps, 100-Mbps, and 1-Gbps links. It is most appropriate when a system needs carrier-oriented Layer-2 switching in a substantial multi-pin package rather than a compact two-port or four-port Ethernet controller. A principal design consideration is lifecycle management. The VSC7416 family is marked End of Life, making the VSC7416XKT-01 appropriate for maintaining an existing qualified design rather than treating it as the default choice for a new platform. Confirm pin assignment, signal timing, power sequencing, thermal performance, and software support using the manufacturer datasheet before schematic capture or PCB release. This product record combines the exact package and Ethernet characteristics, lifecycle status, sourcing information, design guidance, and a conservative replacement assessment. It distinguishes verified drop-in interchangeability from merely similar Ethernet devices, helping engineers identify whether a redesign, firmware adjustment, or qualified alternate device is required before procurement.

RFQ যোগাযোগ
VSC7418XKT-01 - 11-Port Carrier Ethernet Switch | Microchip
VSC7418XKT-01

VSC7418XKT-01 - 11-Port Carrier Ethernet Switch | Microchip

Microchip Technology VSC7418XKT-01 is an 11-port, Layer-2 Carrier Ethernet switch designed for telecommunications and embedded networking systems. The device is supplied in a 284-TQFP package measuring 24 mm by 24 mm and is the orderable -01 version of the VSC7418 family. Its SGMII-oriented Carrier Ethernet architecture supports switching of multiple network-facing ports within compact telecommunications equipment. A Carrier Ethernet switch is a network-interface integrated circuit that forwards Ethernet frames between multiple ports while supporting carrier-grade transport requirements. In the product hierarchy, the VSC7418XKT-01 is a switch IC, then a network interface IC, then an integrated circuit and semiconductor. Its 11-port configuration allows one communications system to consolidate several Ethernet-facing connections without using a separate physical switch for every port. The principal documented feature of this ordered device is its 11-port Layer-2 SGMII Carrier Ethernet implementation. The -01 ordering designation identifies the part covered by the VSC7418-01 datasheet, while the 284-pin TQFP body provides a large, high-pin-count implementation capable of exposing numerous serial network, control, clock, power, and status connections. The 24 mm by 24 mm package is intended for surface-mount PCB assembly rather than manual socket installation. The VSC7418 is identified by Microchip as an End of Life device, making lifecycle planning essential for projects using it. New production should therefore begin with an availability and lifecycle review rather than assuming that an existing inventory position can be replenished indefinitely. The VSC7418XKT-01 suffix also includes an -01 revision and TQFP packaging information that must be retained when comparing documentation or replacement candidates. Typical deployment environments include telecommunications access equipment, Carrier Ethernet aggregation systems, industrial Ethernet equipment, and other network infrastructure that requires a multiport Layer-2 switch. In these systems, the switch IC can organize traffic among service-facing ports while the surrounding board supplies power, clocking, PHY or optical modules, magnetic interfaces, and management circuitry. PCB planning requires care because a 284-pin TQFP has a much larger footprint and more escape routes than a conventional small-outline package. Designers should follow the manufacturer land pattern, maintain high-speed trace geometry, provide local decoupling and reference-clock conditioning, and keep copper-return paths continuous. This page consolidates the confirmed product identity, lifecycle status, package information, sourcing workflow, and engineering considerations relevant to the VSC7418XKT-01.

RFQ যোগাযোগ
VSC7422XJG-04 - 25-Port GbE Switch, 12 Cu PHY | Microchip
VSC7422XJG-04

VSC7422XJG-04 - 25-Port GbE Switch, 12 Cu PHY | Microchip

The Microchip VSC7422XJG-04 is a fully integrated 25-port Gigabit Ethernet (GE) Layer-2 switch with 12 integrated copper PHYs in a single 672-HSBGA (27x27 mm) package, designed for industrial-temperature networking equipment. According to the manufacturer datasheet, this device operates from a 1V supply and combines 12 triple-speed (10/100/1000 Mbps) copper PHYs with up to 25 SerDes/SGMII/QSGMII-capable ports, delivering the industry's first single-chip 25-port GE switch solution. An Ethernet switch IC such as the VSC7422 sits at the heart of managed and unmanaged enterprise, industrial, and small-business networking gear. As a Layer-2 switch, it forwards Ethernet frames at wire speed, enforces VLAN/QoS policies, learns and ages MAC addresses, and provides traffic-class prioritization. Within the broader component taxonomy, the VSC7422XJG-04 is an integrated Ethernet switch IC, a sub-category of interface ICs, descended from telecom and networking ASICs and ultimately from general-purpose digital semiconductors. Key features include industrial-grade -40C to +85C operation, 12 integrated 10/100/1000BASE-T copper transceivers eliminating the need for an external PHY bank, support for 1G/2.5G SerDes plus SGMII/QSGMII mac interfaces on remaining ports, and a flexible unmanaged-L2 feature set. Combined with a companion device such as the VSC8512 (a 12-port copper PHY from the same Microchip SparX-IV family), designers can build a 25-port switch using only two ICs, shrinking BOM cost and PCB area versus discrete-architectures. Architecturally, the VSC7422XJG-04 integrates an L2 forwarding engine, dedicated per-port packet buffers, on-chip termination, and a SERDES physical layer. The device is targeted at designs that need a moderate-to-high port count, unmanaged or lightly-managed switching, and industrial-environment ruggedness without the cost of enterprise-grade managed switches. Typical applications include industrial Ethernet switches, factory-floor networking equipment, IP-surveillance back-haul switches, smart-grid gateways, and small-business / SMB unmanaged switches. For designs requiring 2.5G uplinks, the SERDES lanes can be wired to external PHY or interconnect devices. The 672-HSBGA package demands careful PCB layout: a 4-layer minimum stack-up with an unbroken GND/VDD power island under the exposed die is required to meet IEEE 802.3 return-loss and emission targets. When laying out a VSC7422XJG-04 PCB, design engineers should observe controlled-impedance routing on all copper traces (100-ohm differential for MDI pairs; 50-ohm single-ended for SERDES), maintain at least 200-mil separation between analog/digital grounds unless joined at a single ferrite, and provide sufficient thermal vias under the 672-HSBGA to keep junction temperature within margin when driving all 12 copper ports simultaneously. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB/thermal design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
VSC7422XJQ-02 - 25-Port Gigabit Ethernet Switch | Microchip
VSC7422XJQ-02

VSC7422XJQ-02 - 25-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7422XJQ-02 is a fully integrated 25-port Gigabit Ethernet switch with 12 copper PHYs in a 302-pin TQFP package. It combines Layer 2 switching, 12 integrated 1000BASE-T copper interfaces, and high-speed uplink connectivity in one network-interface IC. The device belongs to the SparX-III-25um switching family and is designed for telecom, industrial, and embedded Ethernet systems requiring a high port count without a collection of separate PHY devices. A Gigabit Ethernet switch is a semiconductor that receives Ethernet frames on multiple ports, inspects destination addresses, and forwards traffic toward the appropriate attached device. Within the network-equipment hierarchy, the VSC7422XJQ-02 sits between a network processor or system controller and physical copper links. As a Layer 2 switch, it provides the physical and data-plane foundation for Ethernet aggregation, access equipment, industrial gateways, and carrier-facing terminal systems. The principal integration advantage is the combination of 25 switch ports and 12 copper PHYs in one package. According to the manufacturer datasheet family, pairing the VSC7422 with a VSC8512 or VSC8522 12-port PHY can produce a 25-port switching solution using only two ICs. This approach reduces board area compared with a design assembled from many discrete Ethernet PHYs, while preserving the familiar Layer 2 forwarding function across copper and uplink connections. The -02 ordering code is associated with the VSC7422-02 datasheet family, which covers the VSC7420-02, VSC7421-02, and VSC7422-02 Gigabit Ethernet switches. The target device is supplied in a 302-TQFP, 24 mm by 24 mm package according to distributor product records. Its large lead count supports the extensive combination of switch ports, SerDes interfaces, copper PHY circuitry, reference clocks, power rails, management signals, and configuration pins required by a carrier-grade multiport Ethernet device. Typical deployments include telecommunications access equipment, industrial Ethernet aggregation, network-interface appliances, and embedded systems that need many Gigabit Ethernet connections. A companion PHY such as the VSC8512 can extend the number of copper ports, while the switching device handles frame forwarding between the integrated PHYs, additional PHY ports, and uplink links. The design must account for high-speed differential routing, controlled clocking, uninterrupted power delivery, thermal performance, and Ethernet magnetics requirements. The principal engineering trade-off is package complexity. A 302-pin TQFP offers extensive connectivity in a surface-mount format, but every assigned signal must be mapped carefully because there are many high-speed and power pins. Follow the pin-description table and recommended reference layout in the manufacturer datasheet rather than relying on a generic 302-pin symbol. Decoupling, return paths, clock-source placement, and copper-impedance control are especially important when integrating this switch into a multilayer PCB. This product overview combines the verified manufacturer family description, package information, architecture, application context, and practical PCB considerations. It also distinguishes the confirmed operating characteristics from detailed electrical parameters that must be taken directly from the official VSC7422-02 datasheet before release to production.

RFQ যোগাযোগ
VSC7422XJQ-04 - 25-Port Gigabit Ethernet Switch | Microchip
VSC7422XJQ-04

VSC7422XJQ-04 - 25-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7422XJQ-04 is a Layer 2 Gigabit Ethernet switch with 25 ports and 12 integrated copper PHYs, housed in a 302-TQFP package measuring 24 x 24 mm. It combines a 25-port managed switch with 12 integrated 10/100/1000Base-T copper PHYs in a single package, reducing the component count and board complexity of a multi-port Ethernet aggregation design. The device is positioned for telecom, industrial, and equipment-level networking applications that require multiple copper Ethernet ports on one controller. An Ethernet switch is a Layer 2 network device that receives Ethernet frames on one port, examines the destination MAC address, and forwards traffic through the appropriate output port. A managed Layer 2 switch adds configuration, monitoring, and traffic-control functions that a basic unmanaged switch does not provide. The VSC7422 combines switching and copper physical-layer functions, allowing twelve copper links to share the same switching silicon while additional interfaces connect the device to upstream processors, PHYs, or network equipment. According to the Microchip VSC7422 product page, the device is the industry's first fully integrated 25-port Gigabit Ethernet switch with 12 copper PHYs in one package. That integration is the defining feature: designers can use one switching IC for twelve copper ports and connect additional ports through external PHYs. Microchip also identifies the VSC8512 as a companion 12-port PHY, enabling a 25-port copper design with only two main ICs when that companion device is used for the remaining interfaces. The VSC7422XJQ-04 is identified in distributor listings as a telecom Ethernet switch with a 302-TQFP package. The large lead count accommodates the integrated copper interfaces, control signals, power rails, and management connectivity in a single surface-mount device. Its footprint is materially larger than a typical low-port Ethernet controller, so PCB area, via density, thermal performance, and assembly capability should be considered before layout begins. Typical deployments include telecom access equipment, industrial Ethernet gateways, network appliances, and managed copper switching platforms. The integrated copper PHYs reduce board-level PHY count, while the Layer 2 switching function consolidates multiple Ethernet links around a single control point. Compared with a board assembled from discrete switching and PHY devices, the integrated approach can shorten copper routing, simplify assembly, and reduce component-inventory complexity. Design the power and thermal plan around the full 302-pin footprint rather than a small Ethernet controller land pattern. Follow the manufacturer layout guidance for high-speed copper pairs, provide clean supply rails and local decoupling, and validate the magnetics and connector interface for the target cable length and isolation requirements. Use the pin-description table and recommended schematic in the manufacturer datasheet when assigning every signal and supplying the exposed thermal and power connections. This page consolidates the manufacturer architecture description, distributor package identification, drop-in replacement information, and board-level design guidance into one engineering-focused reference for the VSC7422XJQ-04.

RFQ যোগাযোগ
VSC7424XJG-12 - 10-Port Gigabit Ethernet Switch | Microchip
VSC7424XJG-12

VSC7424XJG-12 - 10-Port Gigabit Ethernet Switch | Microchip

The Microchip VSC7424XJG-12 is a 10-port managed Layer 2 Gigabit Ethernet switch with eight integrated copper PHYs, supplied in a 672-ball HSBGA package measuring 27 mm by 27 mm. The device is based on the SparX-III-10 family and uses Microchip's 65 nm SimpliPHY technology to integrate copper Ethernet connectivity and switching functions in one package. A serial host interface provides configuration and control access for managed network equipment. A Gigabit Ethernet switch is a network-semiconductor device that receives Ethernet frames on multiple ports and forwards them according to Layer 2 addresses. An integrated copper PHY combines digital Ethernet framing with the physical-layer circuitry required to communicate over twisted-pair cabling. By integrating eight copper PHYs into the switching device, the VSC7424XJG-12 reduces the number of separate physical-layer components required in a multiport network design while retaining centralized packet forwarding and management. The VSC7424 family's defining features include its 10-port configuration, eight integrated copper PHYs, and 65 nm SimpliPHY implementation. Microchip describes the device as a highly integrated and power-conscious option for managed Ethernet switching. The SparX-III-10 designation identifies the switching platform used in the part, while the 672-HSBGA package supports the substantial ball count required for integrated high-speed Ethernet I/O, power delivery, ground connections, and control signals. The device is positioned for equipment that requires several copper Gigabit Ethernet connections in a limited board area. Relevant implementation considerations include careful high-speed layer-transition routing, controlled-length Ethernet differential pairs, solid return-path construction, decoupling close to supply pins, and compliance testing across all ten ports. Because the package is not a standard small-outline package, PCB designers should use the manufacturer's land pattern and pin-assignment documentation rather than infer dimensions from a generic HSBGA drawing. Typical end uses include industrial Ethernet switches, network-interface appliances, embedded communications equipment, access systems, and other managed infrastructure products requiring multiple Gigabit Ethernet ports. For these systems, the integrated copper PHYs can simplify board partitioning, while the serial management interface supports configuration by an embedded host. The trade-off is a large, high-pin-count BGA package whose assembly, inspection, and prototype rework demands are greater than those of a leaded or small-outline switch. This product page consolidates the manufacturer-defined port count, PHY integration, process technology, package, interface, and compliance attributes with application guidance and a clearly scoped replacement analysis. It also distinguishes orderable variants by the electrical details that must be confirmed in the hardware design rather than treating package similarity alone as proof of pin-compatible interchangeability.

RFQ যোগাযোগ
VSC7427XJG-12 - 26-Port Gigabit Ethernet Switch | Microchip
VSC7427XJG-12

VSC7427XJG-12 - 26-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7427XJG-12 is a fully integrated 26-port Gigabit Ethernet switch with 12 copper PHYs in a single 672-HSBGA package measuring 27 x 27 mm. It combines 14 SerDes ports with 12 integrated 10/100/1000BASE-T copper PHY ports, allowing a complete Layer 2 switching system to be designed with fewer external components. The device is based on Microsemi's SimpliPHY technology and is intended for telecommunications, industrial, enterprise, and carrier-grade Ethernet equipment. An Ethernet switch is a semiconductor that connects multiple network endpoints by forwarding Ethernet frames between ports according to MAC-address tables. A Gigabit Ethernet switch supports data rates up to 1 Gb/s per active port. By integrating 12 copper PHYs and 14 SerDes interfaces into one package, the VSC7427 reduces board area, interface complexity, and the number of external PHY components required for a multiport network system. The principal feature of the VSC7427 is its combination of 26 logical ports, 12 integrated copper PHYs, and 14 SerDes interfaces. In conjunction with the Microsemi VSC8512 or VSC8522 12-port PHY, it can form a 26-port Gigabit Ethernet design using two integrated circuits. Its 65 nm SimpliPHY implementation is positioned as a low-power, cost-effective architecture for high-port-count Ethernet systems. The -12 ordering code identifies the exact Microchip catalog variant, while the family designation VSC7427 identifies the SparX-III-26 switching platform. The 672-HSBGA package is designed for surface-mount assembly and is supplied in trays according to the product listing. Its 27 x 27 mm footprint demands careful ball-escape planning, multilayer PCB construction, thermal via arrays, and high-density escape routing. Because the device combines high-speed SerDes interfaces, integrated copper PHYs, and a large switching die, the power, ground, clock, and signal-integrity layout must follow the manufacturer's reference design rather than be treated as a generic BGA layout. Typical uses include access switches, industrial Ethernet gateways, telecom aggregation equipment, storage networks, and embedded network appliances. The integrated copper PHYs reduce system complexity when most deployed endpoints use electrical Ethernet rather than optical fiber. SerDes ports can connect to optical PHYs, backplanes, or additional switching silicon when a design requires fiber uplinks or greater port density. A key design trade-off is package complexity. Integrating 12 PHYs into the switch package simplifies the board-level Ethernet interface, but the 672-ball BGA requires careful escape routing and inspection. Use the Microchip VSC7427 product brief and evaluation-platform documentation for reference layouts, clock requirements, power sequencing, media-dependent interface behavior, and thermal design. This page consolidates the confirmed family specifications, package information, sourcing guidance, and practical implementation considerations into one engineering-focused reference.

RFQ যোগাযোগ
VSC7430XMT - 6-Port Carrier Ethernet Switch | Microchip
VSC7430XMT

VSC7430XMT - 6-Port Carrier Ethernet Switch | Microchip

The Microchip Technology VSC7430XMT is a 6-port Carrier Ethernet switch with two integrated copper PHYs, 2.5 Gbps Ethernet switching capability, and a 324-pin PBGA package measuring 19 mm by 19 mm. It is designed for Carrier Ethernet edge demarcation and access equipment supporting MEF CE 2.0 service delivery. A Carrier Ethernet switch is a dedicated Ethernet switching semiconductor used to aggregate, classify, and forward traffic in telecommunications access networks. Unlike a general-purpose desktop Ethernet switch, a Carrier Ethernet switch is positioned for managed service-provider infrastructure, including service demarcation, mobile backhaul, and enterprise-access systems. The VSC7430 belongs to the broader hierarchy of Ethernet switch → network interface controller → networking semiconductor → integrated circuit. The principal features of the VSC7430XMT include six ports, two integrated Cu PHYs, and 2.5 Gbps switching performance. Its integrated copper PHYs reduce the external component count associated with copper physical-layer implementation, while the six-port architecture supports aggregation and demarcation functions in compact telecommunications equipment. The manufacturer describes the device as a market-ready solution for MEF CE 2.0 service delivery. The 324-PBGA package is a major thermal and routing consideration for high-speed network equipment. A 19 mm by 19 mm land pattern provides ample routing area, but it requires careful layer-transition planning, controlled impedance, power-plane integrity, and adequate thermal dissipation. Because the package has many connections and mixed signal paths, PCB stack-up and component placement can materially affect signal integrity and system reliability. Typical uses include IP edge demarcation platforms, Carrier Ethernet access equipment, enterprise service delivery, and mobile backhaul systems. In these applications, the switch consolidates several Ethernet-facing ports while providing a single switching platform for service handoff. Two integrated Cu PHYs are particularly useful where the system needs direct copper connectivity without a separate physical-layer device for every port. Designers should use the manufacturer datasheet for the authoritative pinout, power rails, clock requirements, reference-design connections, and exposed-pad implementation. Preserve the recommended high-speed trace geometry, provide decoupling close to supply pins, and validate the complete stack-up with the required Ethernet channel and compliance tests before production release. This page consolidates the confirmed VSC7430XMT product identity, package information, switching configuration, sourcing links, and practical implementation guidance. It also distinguishes documented drop-in substitutions from broader functional Ethernet-switch alternatives, helping engineers make package- and pin-compatible decisions rather than treating every competitor switch as interchangeable.

RFQ যোগাযোগ
VSC7435XMT - 6-Port Carrier Ethernet Switch | Microchip
VSC7435XMT

VSC7435XMT - 6-Port Carrier Ethernet Switch | Microchip

The Microchip Technology VSC7435XMT is a Serval-TE carrier Ethernet switch with 6 ports, 2 integrated copper PHYs, and integrated DPLL capability, housed in a 324-BGA package measuring 19 x 19 mm. Designed for IP edge demarcation and access equipment, it targets MEF Carrier Ethernet 2.0 service delivery for enterprise and mobile backhaul networks. A carrier Ethernet switch is a purpose-built network semiconductor that combines packet forwarding, physical-layer interfaces, timing functions, and service-delivery capabilities into one integrated device. The VSC7435XMT occupies the carrier Ethernet switch category within the broader hierarchy of Ethernet interface ICs, telecom semiconductors, and communications processors. Its integrated PHY architecture reduces the number of separate copper transceiver components required in access and edge equipment. The primary functional features are its 6-port Carrier Ethernet switching configuration, 2 integrated Gigabit Ethernet PHYs, and DPLL support. These characteristics make the device relevant to equipment that must aggregate or transport carrier-class Ethernet traffic while supporting synchronization needs associated with mobile backhaul. The 324-BGA package provides a high pin count suitable for the substantial signal, power, configuration, and management interfaces required by this networking equipment class. Microchip positions the VSC7435 within the Serval-TE family as a market-ready solution for MEF CE 2.0 service delivery. Its design targets IP edge demarcation and access equipment rather than general-purpose desktop Ethernet switching. This distinction is important because telecom access designs emphasize service classification, timing, synchronization, reliability, and interoperability with carrier-network operations in addition to conventional packet forwarding. Typical uses include Carrier Ethernet access nodes, mobile backhaul equipment, enterprise service-delivery platforms, and IP edge demarcation systems. In these applications, the integrated copper PHYs can support copper-facing network ports, while the broader switch platform organizes traffic and network services. Timing-sensitive deployments should evaluate the DPLL and synchronization implementation together with the external clocking architecture required by the complete equipment. Designers should base PCB layouts on the manufacturer's pin-definition table and recommended high-speed layout guidance rather than infer connectivity from the package outline. A 324-BGA device also demands careful power-plane design, multilayer stack-up planning, decoupling, and via-current planning. Confirm thermal performance under worst-case traffic and environmental conditions because a high-pin-count communications package concentrates power delivery and high-speed routing requirements in a compact area. This product page consolidates the manufacturer positioning, distributor package information, source links, application context, and design guidance for VSC7435XMT. It also separates confirmed product attributes from engineering details that require the complete datasheet, pin table, hardware design guidance, and qualification information before a production layout or substitution decision is approved.

RFQ যোগাযোগ
VSC7436XMT - 10-Port Carrier Ethernet Switch | Microchip
VSC7436XMT

VSC7436XMT - 10-Port Carrier Ethernet Switch | Microchip

The Microchip Technology VSC7436XMT is a 10-port Carrier Ethernet switch with eight 1G ports, two 10G ports, and two integrated copper PHYs, housed in a 324-ball BGA package measuring 19 x 19 mm. It is designed for telecom access, aggregation, and edge equipment that requires both gigabit and ten-gigabit Ethernet connectivity in a single switching device. The package is surface mount and identified as RoHS3 with MSL3 handling requirements. A Carrier Ethernet switch is a specialized Ethernet switching IC that combines frame forwarding, port management, and carrier-oriented network functions. Unlike a general-purpose desktop Ethernet switch, the VSC7436XMT targets telecommunications infrastructure where port density, uplink bandwidth, timing functions, and interoperability with network equipment are important. Its device family belongs to the broader hierarchy of Ethernet switch, network interface IC, telecommunications IC, and integrated semiconductor categories. The principal connectivity is provided by eight 1G ports and two 10G ports. Two integrated Cu PHYs support copper-connected links without requiring a separate physical-layer transceiver for those interfaces. The VSC7436 family also includes ViSAATM and VeriTime IEEE 1588 capabilities. IEEE 1588 timing support is especially relevant to Carrier Ethernet systems that distribute precise timing across packet networks, while ViSAATM addresses ATM-related transport functions. The 324-BGA package provides a high pin count suitable for a switch containing multiple port interfaces, digital control logic, high-speed serial interfaces, and integrated physical-layer functions. Its 19 x 19 mm body supports compact telecommunications designs while requiring careful PCB layout, high-density escape routing, and assembly processes capable of handling the large ball grid array. The surface-mount package is identified as MSL3, so handling, baking, and reflow controls should follow the manufacturer's assembly guidance. Typical equipment uses include telecom access shelves, mobile backhaul, carrier aggregation platforms, industrial Ethernet gateways, and network appliances with 1G access ports plus 10G uplinks. In these systems, the eight 1G ports can connect subscriber, service, or management equipment, while the two 10G ports provide higher-bandwidth links toward aggregation or core equipment. The integrated copper PHYs can reduce board-level component count where copper connectivity is required. The principal design challenge is not only pin assignment but high-speed signal integrity. Differential Ethernet routes, clocks, power distribution, and decoupling must be designed to prevent insertion loss, reflections, crosstalk, and reference-plane discontinuities from impairing port performance. The manufacturer's pin-description table, layout guidance, and reference design should therefore be treated as the controlling documents during schematic capture and PCB implementation. This page combines the manufacturer's Carrier Ethernet feature description with package, environmental-handling, purchasing, replacement, and engineering guidance. It also identifies where a complete public pin list, detailed electrical limits, lifecycle declarations, and qualified drop-in replacements require separate verification before a board is released for production.

RFQ যোগাযোগ
VSC7440XMT - 10-Port 10G L2/L3 Ethernet Switch | Microchip
VSC7440XMT

VSC7440XMT - 10-Port 10G L2/L3 Ethernet Switch | Microchip

The Microchip Technology VSC7440XMT is a SparX-IV-34 enterprise Ethernet switch IC with up to 10 ports supporting a combination of 1 Gbps, 2.5 Gbps, and 10 Gbps Ethernet links. The device is supplied in a surface-mount 324-BGA package measuring 19 mm by 19 mm and is identified as an L2/L3 enterprise Gigabit Ethernet switch. An Ethernet switch is a network-semiconductor device that receives frames on ingress ports, classifies and processes them, and forwards traffic to the appropriate egress ports. The VSC7440 belongs to the SparX-IV family of switching silicon and integrates Layer 2 switching with Layer 3 routing functions. This places it in the broader hierarchy of Ethernet interface ICs, network processors, connectivity semiconductors, and enterprise switching systems. The VSC7440 supports up to 10 ports across three Ethernet speed classes: 1 Gbps, 2.5 Gbps, and 10 Gbps. Its combination of port speeds allows one device to serve multiple access segments while supporting high-bandwidth uplinks. The manufacturer identifies the device as suitable for SMB and SME Ethernet switching environments, where integration can reduce the number of discrete switching and routing components required in a network system. Technical evaluation must account for the 324-BGA land pattern, high-speed differential routing, clocking, power delivery, thermal performance, and thermal-pad assembly requirements. A 10 Gbps interface requires careful PCB construction because insertion loss, reflection, crosstalk, and impedance discontinuities can affect signal integrity. Differential pairs should be routed as controlled-impedance structures over uninterrupted reference planes, with return paths maintained beneath the pairs. Typical uses include managed access switches, enterprise edge equipment, aggregation systems, and communications platforms that combine copper or fiber-facing interfaces with higher-speed uplinks. Photonic interfaces require compatible optical transceivers and proper isolation from the high-speed copper channels, while copper ports require careful magnetics and impedance-controlled board design. The device is also relevant to systems requiring integrated Layer 2 and Layer 3 traffic handling. Use the manufacturer data sheet as the authoritative source for the complete port map, pin assignment, power rails, maximum clock requirements, register initialization, and thermal limits. System designers should validate the target PCB against the package drawing and reference design before releasing a layout. Firmware, PHY interfaces, SerDes configuration, clock topology, and management software must also be reviewed together rather than treated as independent tasks. This page organizes the device’s network role, package constraints, application guidance, comparison limits, and engineering design considerations into a practical reference for engineers evaluating the VSC7440XMT for multilayer enterprise Ethernet equipment.

RFQ যোগাযোগ
VSC7448YIH-01 - 52-Port 80G Ethernet Switch | Microchip
VSC7448YIH-01

VSC7448YIH-01 - 52-Port 80G Ethernet Switch | Microchip

Microchip Technology VSC7448YIH-01 is a SparX-IV-80 enterprise Ethernet switch with an 80G switching capacity and as many as 52 ports. The device supports a configurable combination of 1G, 2.5G, and 10G Ethernet links and is packaged in a 672-FCBGA measuring 27 x 27 mm. It also provides L2 and L3 switching, making it suitable for industrial Ethernet, telecom, enterprise access, aggregation, and stacking equipment. An Ethernet switch is a network-semiconductor device that receives frames on multiple physical interfaces and forwards them between ports using Layer 2 addresses. A Layer 3 switch additionally performs routing functions, while a stackable switch supports coordinated operation across multiple devices. The VSC7448 belongs to Microchip's SparX-IV-80 family, combining high-density port configurations with 10G uplink capability in one integrated device. The headline features of VSC7448YIH-01 include an 80G switching fabric, support for up to 52 Ethernet ports, and mixed 1G, 2.5G, and 10G port configurations. The 672-FCBGA package provides the dense physical interface required for a high-port-count switching ASIC. A distributor listing also identifies the part as a 52-port L2/L3 stackable Gigabit Ethernet switch with 10 Gbps links. This device targets networking equipment that needs high aggregation capacity without distributing traffic across many external switching components. Its port mix can serve copper or fiber-facing access interfaces through suitable external PHYs, while 10G links support higher-bandwidth aggregation. Enterprise switching features, combined with Layer 3 operation, allow the device to serve in access, distribution, and selected core-adjacent designs rather than only simple unmanaged bridging. Typical uses include industrial Ethernet switches, telecom access equipment, enterprise campus-edge systems, network appliances, and stacked LAN configurations. In these systems, the device can consolidate many lower-speed ports and provide high-speed uplinks. Designers should account for the large BGA thermal and routing requirements, validate the specific port map and protocol stack, and complete high-speed signal-integrity and power-integrity validation on the final board. The most important design consideration is that a 672-ball BGA requires careful escape routing, multilayer PCB construction, controlled-reference-plane geometry, and adequate thermal design. The 27 x 27 mm package also makes system mechanical constraints significant. Use the manufacturer's evaluation guidance and device documentation when defining layer stack-up, power delivery, clocking, SerDes implementation, and connector or PHY placement. This page consolidates the device's port and package characteristics with application guidance, comparison details, and actionable PCB considerations. It is intended to help networking engineers establish whether the VSC7448YIH-01 fits a specific 1G, 2.5G, or 10G industrial Ethernet architecture before beginning high-density BGA implementation.

RFQ যোগাযোগ
VSC7460YIH - 24x1G + 4x10G XAUI Ethernet Switch | Microchip
VSC7460YIH

VSC7460YIH - 24x1G + 4x10G XAUI Ethernet Switch | Microchip

The Microchip Technology VSC7460YIH is a Jaguar-1 family Carrier Ethernet switching circuit that integrates 24 10/100/1000 Mbps Ethernet ports and four 10 Gbps XAUI serial Ethernet ports in a 672-pin HFCBGA package. It is a lead-free, automotive temperature grade device intended for telecommunications and enterprise switching equipment. An Ethernet switch is an integrated circuit that frames and forwards Ethernet packets between multiple ports using dedicated hardware rather than a host processor. It sits below the network processor in the equipment hierarchy and above the physical PHY layer. The VSC7460YIH is a Carrier Ethernet (CE) switch, meaning it adds telecom-oriented functions such as service and port policing, traffic classification, and sub-50 ms protection switching to a conventional enterprise switch core. Key features of the device include 24 copper Gigabit Ethernet ports for 1000BASE-T, 100BASE-TX and 10BASE-T links, four XAUI lanes running at 10 Gbps each for high-speed uplink or stacking connections, and optional support for up to eight 2.5 Gbps Ethernet ports when two of the XAUI lanes are reconfigured. The part is supplied in a 672-pin square CGA-code HFCBGA package and is listed as lead-free (Pb free) with an automotive temperature grade designation. Architecturally, the switch is built around a high-performance packet-processing pipeline with integrated GMII/SGMII management paths, a host processor interface for configuration and telemetry, and table-based forwarding engines sized for Carrier Ethernet service queues. Because the four XAUI ports are consumed by 10 Gbps uplinks, port density on the copper side is decoupled from the number of physical network interfaces a chassis can present, allowing 1 Gbps access ports to be aggregated toward 10 Gbps or 40 Gbps backbones. Typical deployments include telecom access and aggregation shelves, mobile backhaul concentrators, industrial Ethernet aggregation equipment, and enterprise campus access switches requiring 24 copper ports plus high-speed uplinks in a single module. The automotive temperature grade makes the device attractive for harsh-environment industrial and vehicle-network designs that require extended ambient operation. One key design consideration is that the 672-pin HFCBGA demands a multilayer PCB with short, matched high-speed SerDes routing, controlled reference-plane design, and careful power and ground plane distribution around the SerDes sections. Layout should follow the manufacturer reference design for breakout of the XAUI lanes. This page consolidates the manufacturer product-page data, distributor availability listings, packaging detail and application guidance for the VSC7460YIH into one engineering reference, including drop-in family alternatives, a parameter-by-parameter comparison table, and practical board-level design notes.

RFQ যোগাযোগ