উপশ্রেণী

পণ্য (44,000+)

VSC7462YIH - 12x1G + 4x10G Ethernet Switch | Microchip
VSC7462YIH

VSC7462YIH - 12x1G + 4x10G Ethernet Switch | Microchip

The Microchip VSC7462YIH is a Carrier Ethernet switching semiconductor with 12 10/100/1000 Mbps Ethernet ports and four 10 Gbps XAUI Ethernet ports, housed in a 672-pin HFCBGA package. Two XAUI ports can optionally be configured for as many as eight 2.5 Gbps Ethernet ports, giving the device a combined 16-port configuration spanning 10 Mbps, 100 Mbps, 1 Gbps, 2.5 Gbps, and 10 Gbps rates. A Carrier Ethernet switch is a high-performance Ethernet interface device designed to combine packet switching, transport-network awareness, and service-aware traffic management. It belongs to the Ethernet switch, network interface, and communication semiconductor hierarchies. Compared with general-purpose endpoint Ethernet controllers, a Carrier Ethernet switch is intended to aggregate traffic, apply carrier-oriented policies, and provide hardware-assisted forwarding across multiple line-rate interfaces. The VSC7462 is based on Microchip's Virtualized Service Aware Architecture, or ViSAA. This architecture provides the silicon foundation for service-edge and Carrier Ethernet processing functions. The four XAUI interfaces support 10 Gbps links, while the twelve copper Ethernet ports support rates from 10 Mbps through 1 Gbps. This combination allows one switching device to connect lower-rate access traffic to higher-capacity uplinks without requiring separate aggregation silicon for each speed class. A principal implementation consideration is that this is a complex 672-pin BGA device rather than a conventional small-outline interface IC. Its exposed-pad package requires a multilayer PCB, controlled escape routing, extensive ground-plane continuity, and careful high-speed XAUI layout. Power delivery also spans many supply and ground balls, so the design must follow the manufacturer's reference design, recommended decoupling network, and ball-assignment guidance rather than treating the package as a simple two-rail part. Typical uses include Carrier Ethernet service-edge equipment, mobile backhaul, metro aggregation, access-network equipment, packet-processing platforms, and systems that combine 1 Gbps copper ports with 10 Gbps uplinks. The XAUI interfaces can also support 2.5 Gbps configurations, making the device useful where operators are migrating access links while preserving higher-rate backbone capacity. Engineers should treat board compatibility, firmware, PHY integration, clocking, and software configuration as a complete design decision rather than a component substitution. The VSC7462 family is associated with the VSC6810 CEServices software package and related managed-switch development environments. Those tools and the reference hardware materially affect bring-up performance and feature enablement. This page consolidates the verified port configuration, package information, architecture, sourcing details, and engineering considerations for VSC7462YIH. It also distinguishes documented device capabilities from parameters that require confirmation in the manufacturer datasheet, helping engineers plan schematic, PCB, thermal, and software integration before committing a 672-pin Carrier Ethernet design to production.

RFQ যোগাযোগ
VSC7511XMY - 4-Port Gigabit Ethernet Switch | Microchip
VSC7511XMY

VSC7511XMY - 4-Port Gigabit Ethernet Switch | Microchip

The Microchip Technology VSC7511XMY is an unmanaged 4-port Layer-2 Gigabit Ethernet switch with four integrated copper PHYs or four SGMII interfaces in a 172-pin QFN package with an exposed pad. It combines four Gigabit Ethernet ports, hardware-assisted Layer-2 forwarding, 1G/6G SerDes capability, and PTP hardware timestamping in one package. The device is positioned as a low-power switching solution for industrial Ethernet equipment. A Gigabit Ethernet switch is a network-semiconductor device that receives Ethernet frames on one or more ports, examines Layer-2 information, and forwards frames to the appropriate destination ports. The VSC7511XMY belongs to the Ethernet switch hierarchy within interface ICs and is intended for compact embedded systems requiring multiple Gigabit Ethernet connections without a separate external switch chipset. Its four integrated copper PHYs simplify implementation because each port includes the physical-layer interface required for a copper Ethernet connection. Alternatively, the device supports four SGMII interfaces for systems that use serial SerDes connections rather than integrated copper ports. This flexibility permits one switching device to address multiple industrial networking architectures. The verified source material also identifies 1G/6G SerDes operation and hardware timestamping support for PTP-oriented equipment. The switch includes basic and advanced classifiers that determine frame properties such as VLAN membership, QoS class, and drop precedence. These classifications support policing, frame marking, statistics collection, security enforcement, Layer-2 forwarding, and frame rewriting. Such Layer-2 services make the device suitable for industrial gateways, automation controllers, communication equipment, and embedded network appliances where deterministic Ethernet behavior is valuable. Typical uses include industrial Ethernet switches, factory-floor gateways, programmable automation controllers, transport and infrastructure equipment, and embedded telecom or test systems. In each case, four integrated ports can reduce the number of external PHY devices while preserving Layer-2 switching throughput. The integrated-PHY configuration is particularly useful where board area and component count are constrained. Designers should confirm the exact pin assignments, exposed-pad connection, supported SGMII mode, clocking arrangement, and thermal-management requirements from the manufacturer datasheet before layout. Because this is a high-pin-count mixed-signal network IC, careful differential-pair routing, uninterrupted supply planes, solid grounding, and compliance testing for the intended copper Ethernet environment are essential. This page consolidates the verified distributor, manufacturer, and cross-reference information with practical application guidance, a parameter comparison, and explicit data-gap notes. It distinguishes verified VSC7511XMY capabilities from broader switch devices that are not confirmed as pin-to-pin replacements.

RFQ যোগাযোগ
VSC7512XMY - 10-Port Gigabit Ethernet Switch | Microchip
VSC7512XMY

VSC7512XMY - 10-Port Gigabit Ethernet Switch | Microchip

Microchip Technology VSC7512XMY is an unmanaged Layer-2 Gigabit Ethernet switch with 10 ports and four integrated copper PHYs, supplied in a 172-QFN dual-row surface-mount package with an exposed pad. The verified product information identifies a 1.2 V supply and an operating-temperature range of -40°C to +125°C, making the device suitable for industrial networking equipment requiring integrated copper connectivity and an extended temperature range. A Gigabit Ethernet switch is a network-interface semiconductor that forwards Ethernet frames between connected devices at Layer 2 of the OSI model. Unlike a routed network processor, the VSC7512 provides transparent frame switching without adding IP-routing functions. Its integrated copper PHYs combine digital switching, physical-layer transceiver functions, and copper media interfaces within one device, reducing the number of external network components required in compact industrial Ethernet designs. The primary features verified for the VSC7512 include full integration of four copper PHYs and a total of 10 Gigabit Ethernet ports. The device is marketed as an unmanaged industrial Ethernet switch, so its core function is local frame forwarding rather than configuration through a network management interface. The manufacturer describes it as a low-power Gigabit Ethernet switching solution, differentiating it from designs that require multiple discrete PHY components for copper ports. The VSC7512 belongs to the Ethernet-switch and network-interface IC hierarchy, where it combines a Layer-2 switch, integrated physical-layer transceivers, and copper Ethernet ports in one package. This integration supports designs for industrial control cabinets, factory automation networks, and embedded Ethernet equipment. Its -40°C to +125°C operating range makes it appropriate for environments where commercial-temperature networking components may be insufficient, although designers should still verify complete system thermal requirements. Typical uses include unmanaged industrial Ethernet switches, factory-floor connectivity equipment, embedded control systems, and compact network-interface appliances. The VSC7512 can reduce board area by integrating four copper PHYs, but the exposed-pad package still requires careful PCB thermal design, adequate copper area, and verification of the manufacturer's recommended layout and reflow conditions. Designers should follow the manufacturer datasheet for the complete 172-pin assignment, exposed-pad connection, power-supply decoupling, magnetics interface, and layout guidance. The supplied web excerpts do not include a verified pin-by-pin map or detailed electrical limits, so those values must be checked against the official datasheet before schematic capture or PCB release. This product record consolidates verified manufacturer and distributor information, purchase context, technical applications, and selection guidance. It also distinguishes documented capabilities from unavailable details, avoiding unsupported claims about pricing, pin assignments, compliance, and substitute devices.

RFQ যোগাযোগ
VSC7513XKS - 8-Port Industrial Ethernet Switch | Microchip
VSC7513XKS

VSC7513XKS - 8-Port Industrial Ethernet Switch | Microchip

The Microchip Technology VSC7513XKS is an 8-port industrial Ethernet switch with 4 integrated copper PHYs. It supports a combination of 1G and 2.5G Ethernet ports and is designed for industrial Ethernet and SMB switching systems. The device is packaged as a 256-pin PBGA measuring 17 mm by 17 mm. Its feature set includes VLAN and QoS processing, intelligent frame processing, egress frame manipulation, security functions, and distributed timing technology for industrial applications. An Ethernet switch is a semiconductor that connects multiple network nodes and forwards Ethernet frames according to learned or configured MAC addresses. The VSC7513 family belongs to the broader category of Ethernet interface ICs, network switches, communication semiconductors, and industrial automation components. Unlike a simple physical-layer transceiver, this device combines multiple Ethernet ports, frame processing, traffic management, and timing functions within one switching platform. The VSC7513XKS provides 8 switching ports and integrates 4 copper PHYs, allowing industrial equipment or network infrastructure to use a compact switch implementation. Its combination of 1G and 2.5G Ethernet support is relevant for factory automation, industrial gateways, embedded systems, and SMB equipment that need managed local connectivity. The manufacturer describes the device as supporting industrial and enterprise Ethernet switching features. The switch uses multi-stage TCAM technology for VLAN and QoS processing. This supports traffic classification and differentiated service delivery. Intelligent frame processing provides security-related capabilities, while egress frame manipulation can support traffic shaping and system-level network requirements. The integrated distributed timing technology is particularly relevant to industrial systems that need deterministic synchronization across connected equipment. VSC7513XKS is intended for applications where a compact, highly integrated switching device can simplify board design compared with a discrete collection of Ethernet PHYs and supporting controllers. The 256-PBGA package is a substantial surface-mount package, so PCB layout must provide adequate thermal and electrical performance and must follow the manufacturer’s land pattern and reference design guidance. The supplied web sources confirm the function, port configuration, integrated PHY count, package format, and core switching capabilities; detailed electrical limits, pin assignments, thermal ratings, clocking requirements, and power-consumption values were not included in the provided data. This page is intended to support initial engineering selection for the VSC7513XKS. Before committing to a design, consult the official VSC7513 data sheet, errata, hardware design guidance, and reference designs to verify power rails, interfaces, timing constraints, package layout, thermal performance, and software support. The device should be selected primarily when its integrated 8-port industrial Ethernet architecture and 1G/2.5G flexibility are required, rather than as a generic low-cost Ethernet switch.

RFQ যোগাযোগ
VSC7514XKS - 10-Port 2.5G Industrial Ethernet Switch | Microchip
VSC7514XKS

VSC7514XKS - 10-Port 2.5G Industrial Ethernet Switch | Microchip

The Microchip Technology VSC7514XKS is a 10-port Gigabit Ethernet and SMB managed-switch IC supporting a combination of 1G and 2.5G Ethernet ports, supplied in a 256-pin PBGA package measuring 17 mm by 17 mm. The device is positioned for industrial and enterprise Ethernet systems that require multiport Layer 2 switching, integrated copper PHYs, and support for both Gigabit Ethernet and 2.5G Ethernet links. Its 10-channel network-switch architecture consolidates several Ethernet interfaces into one dedicated switching component. A managed Ethernet switch is a semiconductor that receives Ethernet frames from multiple ports, examines destination addresses, and forwards traffic to the appropriate port or ports. In the broader product hierarchy, the VSC7514XKS is an Ethernet interface IC, then a network switch IC, then an integrated circuit and semiconductor. Unlike a discrete Ethernet PHY, this device combines multiple port interfaces, integrated copper PHYs, and switching functions within one package. The VSC7514 family provides 10 Gigabit Ethernet or SMB ports, with four integrated copper PHYs identified in the distributor product description. This combination lets equipment designers support mixed-speed industrial networks without implementing every physical-layer function as a separate device. The 256-PBGA package provides the interconnect density needed for the device's parallel data paths, power connections, management signals, and reference clock circuitry. The switch is designed for industrial and enterprise Ethernet equipment, where local port aggregation and deterministic network segmentation can simplify system architecture. Its combination of 1G and 2.5G links is relevant to machine vision, industrial automation, factory gateways, network infrastructure, and embedded edge equipment. Compared with a collection of discrete PHY components and an external switching ASIC, an integrated managed-switch IC can reduce board-level component count while centralizing network configuration. The VSC7514XKS is also suitable for embedded systems that need multiple copper Ethernet ports, including industrial controllers, communication equipment, and network appliances. System designers should consult the Microchip product page and the VSC7514 datasheet for the authoritative port map, electrical limits, clock requirements, initialization sequence, package ball map, and supported software configuration before releasing a PCB. A 256-pin PBGA requires careful PCB layout, continuous high-speed return paths, controlled reference-clock routing, and a thermal design appropriate for the device's dissipation. Differential Ethernet pairs should be routed according to the Microchip reference design and signal-integrity guidance. Adequate layer stacking, copper thermal spreading, and locally placed decoupling are especially important because this package concentrates many interfaces in a small area. This product page consolidates the verified manufacturer and distributor information into an application-oriented summary, highlights where design data is still required, and separates documented capabilities from unverified assumptions. It also documents why the listed competitor Ethernet devices are not presented as drop-in replacements without package, ball-map, firmware, and feature-level verification.

RFQ যোগাযোগ
VSC7982XYE - 11.3 Gb/s 3.3V Laser Driver | Microchip
VSC7982XYE

VSC7982XYE - 11.3 Gb/s 3.3V Laser Driver | Microchip

Microchip Technology VSC7982XYE is a low-power 3.3V laser and modulator driver capable of data rates up to 11.3 Gb/s. The device is designed for VCSEL, directly modulated laser, and electro-absorption modulated laser (EML) signal chains, and it is offered in a compact low-cost QFP-N package optimized for small-footprint optical communications equipment. A laser and modulator driver is an interface IC that converts high-speed digital data into the current-driven electrical signal required by optical transmitters. Within the optical communication hierarchy, the VSC7982XYE combines a data path, modulation output, bias control, and on-chip operational amplifiers to reduce the number of external components needed around a laser or modulator. It therefore sits between the digital transceiver circuitry and the optical transmitter module. The principal operating characteristics include a maximum data rate of 11.3 Gb/s, a 3.3V power supply, and support for VCSEL, DML, and EML light sources. The family documentation also identifies low-power operation as a key benefit. Integrated on-chip operational amplifiers are intended to provide stable output modulation and output-bias control, helping reduce the discrete component count on the transmitter board. The VSC7982 family architecture is tailored to high-speed optical links where modulation current must be controlled accurately while the physical implementation remains compact. Low-cost QFP-N packaging supports production layouts where optical modules and line cards require many closely spaced high-speed driver channels. Because this device controls bias and modulation, PCB signal integrity, supply decoupling, return-path continuity, and controlled-impedance routing directly influence achievable data rate and eye quality. Typical uses include 10.3G and 10G-class optical transceiver modules, VCSEL transmitters, DML transmitters, EML transmitters, telecommunications equipment, and data-communications links. It can also be evaluated for test and measurement systems, instrumentation, and industrial optical-control modules that require a compact high-speed current driver. The device is particularly relevant where a fixed-function laser driver is preferable to a general-purpose amplifier and discrete current-source network. When laying out a circuit using the VSC7982XYE, place decoupling capacitors close to the supply and ground pins and preserve a continuous return path beneath the high-speed package. Use the manufacturer's reference design and pin-description tables for exact power, ground, bias, modulation, and control connections. Confirm the output-impedance and optical-module requirements of the selected laser before finalizing resistor values and termination arrangements. This page organizes the verified VSC7982XYE characteristics, purchase and availability guidance, family-level comparisons, application context, and practical design considerations. It also distinguishes documented capabilities from parameters that require confirmation in the manufacturer datasheet, helping engineers move from component selection to a defensible PCB implementation.

RFQ যোগাযোগ
VSC7984XYF - 11.3 Gb/s EAM Driver | Microchip Technology
VSC7984XYF

VSC7984XYF - 11.3 Gb/s EAM Driver | Microchip Technology

The Microchip Technology VSC7984XYF is an electroabsorption modulator driver for SONET/SDH and 10 GbE optical-transmission equipment, with the device described as an 11.3 Gb/s clocked driver and associated documentation also identifying a 12.5 Gb/s operating capability. It supports selectable data retiming to improve jitter performance while providing external controls for output bias voltage, modulation voltage, and duty cycle. The component is associated with a QFN package, although the exact package dimensions and pin count are not established by the accessible manufacturer information. An electroabsorption modulator driver, or EAM driver, is an interface IC that converts high-speed electrical data into the differential drive signals required by an electroabsorption-modulated optical transmitter. It belongs to the optical communication interface hierarchy: EAM driver, interface IC, integrated circuit, and semiconductor. Its primary role is to preserve signal integrity while delivering sufficient modulation voltage and bias conditions to an external optical modulator. Selectable data retiming is the central performance feature of the VSC7984XYF. Retiming can resynchronize the incoming data stream to an internal or associated clock, helping reduce jitter in systems where source-device timing and transmitter-chain alignment are imperfect. The output-bias, modulation-voltage, and duty-cycle controls allow the driver to be adjusted to the requirements of the optical modulator and its surrounding drive network. The device also incorporates internal operational amplifiers and an on-chip voltage reference. These functions reduce the amount of external circuitry needed to establish stable modulation and bias conditions. Internal amplification can simplify the signal path, while the reference supports repeatable control of the driver's operating state. The clocked architecture remains sensitive to trace routing, supply integrity, and the quality of the high-speed differential connections. Typical uses include 10 GbE optical modules, SONET/SDH transmit equipment, optical transport systems, and other 10.3125 Gb/s-class optical interfaces. The VSC7984XYF is most appropriate where an external electroabsorption modulator requires controlled bias, adjustable modulation drive, and selectable retiming. Its suitability in a specific design still depends on the complete modulator interface, target jitter margin, and required data-rate classification. When laying out a circuit around the VSC7984XYF, keep the high-speed differential output paths short and impedance-controlled, provide clean return paths, and place decoupling and termination components close to their associated pins. Confirm the exact pin assignments, exposed-pad requirements, supply sequencing, and output-impedance settings in the manufacturer datasheet before release to manufacturing. This page organizes the verified VSC7984XYF technical facts, sourcing information, application guidance, and design considerations into one engineering reference. It also distinguishes directly documented capabilities from package details and lifecycle information that must be confirmed before a new design is released.

RFQ যোগাযোগ
VSC8115XYA-T - 622 Mbps Clock Recovery Unit | Microchip
VSC8115XYA-T

VSC8115XYA-T - 622 Mbps Clock Recovery Unit | Microchip

The Microchip Technology VSC8115XYA-T is a 622 Mbps clock recovery unit (CRU) for SONET/SDH and dense wavelength division multiplexing applications. It provides one recovered-clock output in a 20-pin TSSOP package and is supplied in lead-free tape-and-reel packaging. The device belongs to the application-specific clock and timing IC family, where clock and data recovery circuits restore timing information from transmitted data streams. A clock recovery unit is a specialized timing IC used in high-speed digital communication systems. Its role within the optical-transceiver hierarchy is to extract or recover a usable clock from a serial data stream when the transmitted signal no longer carries a separate clock conductor. Clock recovery units support communication infrastructure by helping downstream digital logic operate from a timing reference synchronized to the incoming data. The VSC8115XYA-T is identified as a single-channel, 622 Mbps device with one output. Its principal documented characteristics are its 622 Mbps operating rate, one recovered output, 20-pin TSSOP construction, and lead-free tape-and-reel delivery format. These details position it for SONET/SDH, DWDM, and related telecom signal-conditioning designs where a dedicated recovery function is required. Clock recovery differs from ordinary clock generation because the IC must derive stable timing from a data stream that may have accumulated timing variation. In a practical optical communication path, a recovered clock can feed parallelizing logic, a descrambler, a retimer, or another digital processing block. Correct implementation depends on the interface requirements of the surrounding equipment, including data rate, reference-clock arrangement, logic level, and jitter tolerance. Typical uses include 622 Mbps line-card interfaces, SONET/SDH transport equipment, DWDM optical networking, telecommunications test equipment, and clock-recovery sections of optical transceivers. The 20-pin TSSOP package also allows reuse of board layouts intended for compatible 20-pin clock-and-timing devices. The VSC8115XYA-06-T is a closely related family member listed at the same 622 Mbps operating point. Before laying out a replacement board, verify the complete pin arrangement, electrical limits, reference requirements, and timing behavior in the Microchip manufacturer datasheet. A mechanically similar 20-pin package alone does not establish signal compatibility, especially for a clock-recovery interface whose internal architecture and pin functions must match the original design. This product page combines the verified 622 Mbps and 20-pin TSSOP characteristics with family-level alternatives, application guidance, and design checks that support faster component selection and board-level planning.

RFQ যোগাযোগ
VSC8211XVW - 1-Port GbE Cu/Fiber PHY, 117-LBGA | Microchip
VSC8211XVW

VSC8211XVW - 1-Port GbE Cu/Fiber PHY, 117-LBGA | Microchip

The Microchip Technology VSC8211XVW is a single-port Gigabit Ethernet copper/fiber PHY transceiver that combines a 1.25 Gbps SerDes with a triple-speed (10/100/1000BASE-T) transceiver in a 117-LBGA (10x14 mm) package. The device operates from a 3 V to 3.6 V supply and supports copper PHY, 1000BASE-X fiber PHY, and 100BASE-FX media converter configurations with automatic media detection. A PHY (Physical Layer transceiver) is the interface block that converts between raw digital data and electrical or optical signaling on a copper or fiber link. In the system hierarchy, a PHY sits below the MAC (Media Access Control) block, which in turn sits below the network switch or host controller. Transceivers combine a PHY with parallel MAC-side interfaces so that a single silicon device can terminate a physical link while handing data to a MAC layer over a standard bus. Key features of the VSC8211XVW include full triple-speed auto-negotiation support, a 1000BASE-X compliant SerDes for fiber modules, and a wide set of MAC-side ports: GMII, RGMII, MII, TBI, and RTBI. The two serial interfaces (SGMII/1000BASE-X SerDes and the parallel MAC ports) let a system reduce signal overhead compared with a purely parallel GMII connection while still supporting legacy 10/100 MII-based MACs. Technically, the device combines an integrated 1.25 Gbps SerDes with a copper PHY capable of 10, 100, and 1000 Mb/s operation, using patented line driver technology that improves tolerance to noise and cable-plant imperfections. Auto-Media detection allows copper and fiber ports to be supported with one physical network port, reducing connector count and board area in media converter designs. Typical applications include Gigabit uplinks on Fast Ethernet switches, fiber-to-copper media converters, 100BASE-FX industrial and campus links, GBIC and SFP optical module designs, and industrial Ethernet equipment requiring a single PHY that bridges copper and fiber media. Design guidance: the 117-LBGA package demands careful via-in-pad and thermal-via layout, and the high-speed SerDes and copper pairs require controlled-impedance routing with clean references. Confirm regulator sequencing and 3.3 V rail decoupling close to the supply pins. This page consolidates manufacturer datasheet detail, interface compatibility analysis, drop-in alternatives in the same package family, and practical PCB guidance that is not gathered in one place in the original device documentation.

RFQ যোগাযোগ
VSC8221XHH - Low-Power Gigabit Copper SFP PHY | Microchip
VSC8221XHH

VSC8221XHH - Low-Power Gigabit Copper SFP PHY | Microchip

Microchip Technology VSC8221XHH is a low-power Gigabit Ethernet over copper PHY with a 1.25 Gbps SerDes, a single 3.3 V supply, and less than 700 mW power consumption. It supports 10BASE-T, 100BASE-TX, and 1000BASE-T through a 100-TFBGA 9 x 9 mm package. The device is designed for copper SFP, GBIC, and media-converter equipment. A copper Ethernet PHY is a physical-layer transceiver that translates digital MAC data into signals suitable for twisted-pair cabling and recovers those signals at the receiving endpoint. The VSC8221 occupies the PHY layer within the Ethernet hierarchy: an Ethernet transceiver integrates a physical-layer device with a SerDes interface for connection to a media-access controller or switching fabric. Its purpose is to provide interoperable copper connectivity while limiting module power and board area. The principal feature is support for triple-speed copper Ethernet at 10, 100, and 1000 Mb/s. Its 1.25 Gbps SerDes supports both SGMII and SerDes-to-Category 5 operating modes, allowing the same PHY to be used in SFP and media-converter designs. The manufacturer identifies the part as the smallest, lowest-power Gigabit Ethernet-over-copper PHY in its product family and as suitable for demanding cable-plant environments. The VSC8221 is designed to support 140 m of Category 5 unshielded twisted-pair cable while meeting stringent SFP power-consumption requirements. It also supports PICMG 2.16 and 3.0 Ethernet backplanes at approximately 500 mW and provides tolerance to NEXT, FEXT, echo, and system noise. These characteristics make the PHY appropriate where copper reach, electromagnetic-noise immunity, and compact module power are simultaneous design priorities. Typical uses include 1000BASE-X copper SFP modules, GBIC-style copper interfaces, Ethernet media converters, and backplane or embedded networking equipment. The same package can support a MAC-to-copper connection through 1000BASE-X SerDes operation or a MAC connection through the four-pin or six-pin SGMII interface. Automatic or user-controlled SerDes behavior provides additional flexibility during system bring-up. When designing with the VSC8221, verify the selected magnetics, impedance-controlled copper routing, reference clock, and SGMII or SerDes interface against the manufacturer data sheet. A 3.3 V-only architecture simplifies supply design, but the complete module still requires careful thermal, isolation, and return-path planning under sustained 1 Gb/s traffic. This page consolidates the verified manufacturer and distributor information for VSC8221XHH, including power, interface, speed, cable-reach, pricing, and application details. It also identifies the limits of the available substitute data so engineers can distinguish confirmed same-family options from unsupported cross-brand replacements.

RFQ যোগাযোগ
VSC8224XHG - 4-Port Gigabit Ethernet PHY | Microchip Technology
VSC8224XHG

VSC8224XHG - 4-Port Gigabit Ethernet PHY | Microchip Technology

Microchip Technology VSC8224XHG is a four-port Gigabit Ethernet transceiver IC integrating four independent 10BASE-T, 100BASE-TX, and 1000BASE-T PHYs with four 1000BASE-X-compatible serializer/deserializer interfaces in a thermally enhanced 260-pin plastic ball grid array package. The device operates from a 3.3 V supply and combines copper and fiber-oriented network connectivity in one 19 mm package. An Ethernet PHY is a physical-layer interface IC that converts digital MAC data into electrical signaling for a network medium and converts received signaling back into digital data. The VSC8224 belongs to the Ethernet interface IC hierarchy, where each integrated transceiver supports a physical port while coordinating with an external or embedded media-access controller through RGMII or RTBI-compatible interfaces. The principal feature of VSC8224XHG is port density: four independent triple-speed Ethernet transceivers are integrated into one device. Each port supports 10 Mbps, 100 Mbps, and 1 Gbps operation. Four 1000BASE-X-compatible SerDes channels provide an additional high-speed physical interface, while automatic or user-programmable RGMII timing compensation helps accommodate MAC-to-PHY timing differences. On-chip series termination resistors also reduce the need for external receive-side termination components. The thermally enhanced 260-pin PBGA package is intended for high-port-density equipment where four separate physical-layer devices would consume excessive board area. Its four copper PHYs suit switching and routing platforms, while the 1000BASE-X-compatible SerDes channels can support fiber-oriented links when paired with appropriate optical and physical-layer circuitry. The integrated architecture reduces component count and simplifies multiport routing-board layouts. Typical applications include four-port Gigabit Ethernet switches, routers, network interface cards, industrial Ethernet equipment, and communications infrastructure. Design teams must preserve the manufacturer's recommended high-speed layout, provide suitable power and ground distribution, and keep Ethernet magnetics and signal-routing paths compact. Because the package exposes 260 balls, careful thermal management and via-array layout are essential. This page consolidates verified distributor pricing, package information, functional application guidance, and cross-reference findings that are not presented together in a typical distributor listing. It also distinguishes the confirmed VSC8224XHG orderable variant from related VSC8224 documentation and avoids asserting unverified pin-level substitutions.

RFQ যোগাযোগ
VSC8228XRC-01 - Dual 4.25G Retimer | Microchip
VSC8228XRC-01

VSC8228XRC-01 - Dual 4.25G Retimer | Microchip

The Microchip Technology VSC8228XRC-01 is a dual-port, dual-output clock and data recovery retimer supporting serial link rates from 125 Mbps to 4.25 Gbps in a 64-pin TQFP package measuring 10 mm by 10 mm. The device provides two FibreTimer clock recovery units for bidirectional signal conditioning in system interconnect and serial backplane applications. A clock and data recovery IC, or CDR, extracts timing information from a corrupted or degraded serial stream and reconstructs a clean data and clock output. Within the hierarchy of integrated circuits, a CDR belongs to the Clock & Timing and Interface IC families, supporting reliable data transfer when transmitted signals experience attenuation, jitter, or noise. The VSC8228 is designed for Fibre Channel, Gigabit Ethernet, SONET/SDH, and InfiniBand system interconnect. The primary features of the VSC8228XRC-01 include two retiming ports, support for data rates up to 4.25 Gbps, operation from a minimum rate of 125 Mbps, and two independent clock recovery units. Its dual-channel architecture allows a single device to condition two serial links, reducing component count and simplifying board-level clock distribution. The 64-TQFP surface-mount package also supports compact backplane and communications equipment layouts. Technically, the FibreTimer architecture separates clock recovery from ordinary signal buffering and performs bidirectional signal conditioning. This is particularly useful when loss, skew, or accumulated jitter would compromise a high-speed point-to-point link. A single reference clock can be used for acquisition, allowing the two recovered channels to share a coherent timing reference. Confirm the required reference-clock topology, operating mode, and channel configuration against the Microchip VSC8228 documentation before laying out the PCB. Typical uses include Fibre Channel links, Gigabit Ethernet backplanes, SONET/SDH equipment, and InfiniBand interconnects. The device is also appropriate for proprietary serial backplanes operating at or below 4.25 Gbps where recovered clock and data outputs are required at both ends of a link. PCB implementation should prioritize short, controlled-impedance traces, solid reference planes, and symmetric routing between the transmit and receive channels. Place clock-generation and decoupling networks close to their associated device pins, and follow the manufacturer’s recommended termination and layout guidance to minimize signal-integrity degradation. This page combines the manufacturer’s device description with application-focused engineering guidance, package information, sourcing questions, and selection criteria that help engineers determine whether the VSC8228XRC-01 fits a high-speed recovery or retiming requirement.

RFQ যোগাযোগ
VSC8242XHX-01 Ethernet Interface Controller | Microchip
VSC8242XHX-01

VSC8242XHX-01 Ethernet Interface Controller | Microchip

The Microchip Technology VSC8242XHX-01 is an Ethernet interface controller associated with the VSC8242 family of multi-port 10/100/1000BASE-T physical-layer devices. Its family supports RGMII and RTBI MAC interfaces, positioning it for network equipment that requires multiple copper-Ethernet ports connected to a switching or processing subsystem. An Ethernet interface controller is a semiconductor that manages communication between a MAC, network processor, or switching fabric and physical network media. Within the network hierarchy, the controller sits above the PHY layer and below the packet-processing layer. Its operating role is therefore distinct from a general-purpose microprocessor: the surrounding system supplies packets and configuration, while the controller interfaces those signals with copper Ethernet ports. The key documented feature of the related VSC8244 listing is quad-port 10/100/1000BASE-T operation with RGMII and RTBI MAC interfaces. The VSC8242XHX-01 shares the same Vitesse and Microchip Technology product lineage and is identified as an interface controller. Detailed electrical ratings, interface timing, register definitions, and operating limits for the exact XHX-01 ordering code should be confirmed in the manufacturer datasheet before the device is released into production. Network-interface applications include managed Ethernet switches, industrial Ethernet equipment, network appliances, telecommunications access hardware, and multi-port embedded systems. In these systems, the controller reduces the number of discrete media-access and PHY interface functions required on the main board while providing a standardized path between the Ethernet PHYs and the switching or host logic. A quad-port configuration can also simplify board routing when several copper ports are needed in one chassis. The controller still requires careful treatment of high-speed digital interfaces, including controlled-impedance routing, solid reference planes, and minimized differential-pair crosstalk. Magnetic-interface protection and external line filtering are normally implemented separately from the controller. Before layout begins, download the manufacturer datasheet and confirm the XHX package drawing, exposed-pad requirements, pin assignments, reference-voltage circuitry, clock expectations, and decoupling recommendations. The package used by this ordering code is not identified consistently across product listings, so its mechanical dimensions and land pattern must not be inferred from a generic QFN footprint.

RFQ যোগাযোগ
VSC8244XHG - Quad Gigabit Ethernet PHY | Microchip Technology
VSC8244XHG

VSC8244XHG - Quad Gigabit Ethernet PHY | Microchip Technology

The Microchip Technology VSC8244XHG is a quad-port Gigabit Ethernet PHY transceiver with 10/100/1000BASE-T support, RGMII and RTBI MAC interfaces, four drivers and four receivers, and a 260-PBGA package. It operates from a 3 V to 3.6 V supply and is designed for low-cost Ethernet switch, router, and embedded networking equipment. A multi-port Ethernet PHY is an interface IC that converts data between a digital MAC or switching fabric and physical copper network links. The VSC8244 family combines four Gigabit Ethernet channels in one device, reducing the number of external PHY components required in a network system. Its RGMII interface supports high-speed digital connections to a network processor or switch ASIC, while RTBI provides an alternative MAC-facing interface for compatible designs. The principal feature of the VSC8244XHG is its quad-port architecture, which allows one device to terminate four Ethernet ports. The manufacturer describes the VSC8244 as the industry’s smallest, lowest-power quad-port Gigabit Ethernet transceiver for low-cost RGMII and RTBI switch and router applications. In 1000BASE-T mode, the manufacturer states that power consumption is 30% lower than the next-best competitor. The 3 V to 3.6 V operating range suits systems using a regulated 3.3 V power rail. The 260-PBGA package provides a high pin count for four integrated channels and their associated interfaces, while its lead-free construction and RoHS compliance support modern manufacturing requirements. The exact pin assignments, register map, clocking requirements, and electrical limits should be taken from the Microchip VSC8244 datasheet and reference design documentation. Typical applications include four-port Gigabit Ethernet switches, router interfaces, industrial Ethernet equipment, network appliances, and embedded systems that need multiple copper Ethernet ports. The PHY is positioned between the Ethernet magnetics and the system’s MAC or switching logic, so board design must account for high-speed digital signals, differential pairs, controlled impedance, grounding, and isolated network interfaces. For a new design, compare the complete Microchip VSC8244 datasheet, reference schematics, and support for the intended MAC interface before layout begins. The quad-channel package is not interchangeable with a single-channel PHY, and the 260-BGA land pattern requires careful fanout and via planning.

RFQ যোগাযোগ
VSC8247YJB-01 - 10G Quad CDR with EDC | Microchip
VSC8247YJB-01

VSC8247YJB-01 - 10G Quad CDR with EDC | Microchip

The Microchip Technology VSC8247YJB-01 is a quad-channel clock and data recovery IC with adaptive electronic dispersion compensation (EDC), four outputs, and a 144-FCBGA package measuring 13 mm by 13 mm. It operates from 8.5 Gbps to 11.3 Gbps per channel and supports 10G Ethernet, SONET, 8G Fibre Channel, and 10G QDR InfiniBand protocols. A clock and data recovery IC is a high-speed interface component that reconstructs a usable clock from a received serial data stream. Where the incoming signal has experienced timing jitter or channel dispersion, the CDR detects timing deviation and adjusts its recovered clock. EDC adds adaptive equalization to compensate for signal degradation, making the VSC8247YJB-01 suitable for demanding serial links rather than ordinary low-speed interface recovery. The primary features of the device are four independent recovery channels, four clock outputs, an 8.5 Gbps to 11.3 Gbps operating range, and integrated adaptive EDC. These characteristics allow one device to serve multiple high-speed lanes in a networking or storage system. The four-output architecture can reduce the number of discrete recovery components required when a board must recover several related signals. Technically, the VSC8247YJB-01 combines clock and data recovery with adaptive dispersion compensation in a single 144-FCBGA package. This integration places timing recovery and channel-loss mitigation beside the physical-layer receive path. The listed protocol support gives designers a practical framework for selecting operating modes, although configuration, reference-clock, media, and electrical requirements must be confirmed against the manufacturer documentation before a board is released. Typical applications include 10G Ethernet ports, SONET/SDH equipment, 8G Fibre Channel links, and 10G QDR InfiniBand interfaces. It can also support multi-lane backplanes, optical-module receive paths, network-interface controllers, and high-speed test equipment where deterministic clock recovery and channel equalization are important. A critical design consideration is that recovery performance depends on the complete channel, including transmitter characteristics, trace losses, connectors, clocking, and receive equalization. PCB layout, power distribution, reference decoupling, and input signal integrity must therefore be developed as part of the high-speed design rather than added after schematic completion. This page organizes the device protocol, package, speed, and channel information into an engineering-focused guide, adds application analysis, and clearly identifies the electrical, pinout, lifecycle, and drop-in replacement details that still require manufacturer confirmation.

RFQ যোগাযোগ
VSC8247YJB-02 - 8.5-11.3 Gbps Quad CDR | Microchip
VSC8247YJB-02

VSC8247YJB-02 - 8.5-11.3 Gbps Quad CDR | Microchip

The Microchip Technology VSC8247YJB-02 is a four-channel clock and data recovery (CDR) and retimer IC for high-speed serial links operating from 8.5 Gbps to 11.3 Gbps. It provides four outputs and is packaged in a 144-FCBGA measuring 13 mm by 13 mm. A clock and data recovery IC is a timing and signal-integrity component that extracts or reconstructs a usable clock from a high-speed serial data stream. It belongs to the clock and timing IC hierarchy within broader interface and semiconductor systems. By recovering timing information and retiming data, a CDR can reduce accumulated jitter and help a receiver interpret a serial signal reliably. The VSC8247 combines four channels in one package for multi-lane networking, optical-module, and backplane applications where parallel channel density is important. The VSC8247 operates across an 8.5 Gbps to 11.3 Gbps line rate, allowing one device family to cover multiple high-speed protocols. Supported applications include 10G Ethernet, SONET, 8G Fibre Channel, 10G QDR InfiniBand, and legacy rates. Its four-channel architecture also makes it suitable for emerging 4×10G and 10×10G CFP-module architectures, as well as high-density photonic integrated circuit designs. Four outputs give each recovered channel a corresponding output path for downstream circuitry. The device integrates clock recovery and retiming functions rather than functioning only as a passive clock distributor. Retiming establishes a new sampling boundary for received serial data, while clock recovery provides a stable timing reference for the associated channel. This is important in multi-gigabit links where transmission-line effects, package parasitics, connector transitions, and inter-symbol interference can degrade the eye opening. The Microchip VSC8247 datasheet identifies the family as a versatile CDR and retimer for 10G-class serial communication. Typical deployments include 10G Ethernet equipment, SONET/SDH interfaces, Fibre Channel systems, QDR InfiniBand links, CFP optical modules, and high-density photonic integrated circuits. The quad-port configuration reduces the number of discrete timing devices needed in a four-lane design, while a single 13 mm by 13 mm FCBGA can support dense line-card and pluggable-module layouts. Designers should evaluate the complete receiver channel rather than relying on nominal line-rate capability alone. Signal losses, connector and package parasitics, reference-clock quality, board-level jitter, and the available power architecture can all affect margin. Confirm the manufacturer’s recommended layout, reference-clock requirements, decoupling network, impedance-controlled interfaces, and thermal conditions against the Microchip VSC8247 datasheet before releasing a high-speed PCB. This product summary consolidates the verified operating range, channel count, output count, supported protocols, package information, and manufacturer datasheet reference for engineers evaluating the VSC8247YJB-02 in high-speed serial-interface designs.

RFQ যোগাযোগ
VSC8248KITEV - Application-Specific Clock/Timing IC | Microchip
VSC8248KITEV

VSC8248KITEV - Application-Specific Clock/Timing IC | Microchip

The Microchip Technology VSC8248KITEV is an application-specific clock and timing integrated circuit listed for clock buffers, drivers, and interface-controller applications. The device is identified by the full VSC8248KITEV ordering code, but the accessible manufacturer and distributor records do not expose its complete electrical specifications, package dimensions, pin configuration, frequency range, or operating-temperature limits. The part is therefore presented as a specialized timing-control device rather than being assigned unverified performance values. An application-specific clock/timing IC is a semiconductor that generates, redistributes, buffers, conditions, or controls clock signals within a larger electronic system. Clock and timing ICs sit within the broader clock and timing IC category, where they support digital logic, communications equipment, industrial controls, and other systems that depend on stable signal propagation. The VSC8248KITEV is specifically categorized as an IC interface controller by multiple product records. The primary identified feature is its specialized role in clock and timing signal handling. Unlike a general-purpose microcontroller, this device is intended to support the timing architecture of its host equipment. Its ordered suffix includes the KITEV package and temperature-grade identifier, but the accessible records do not provide enough information to map those codes to confirmed package dimensions, pin count, lead finish, temperature range, or qualification status. The physical package and symbol should be confirmed against the manufacturer datasheet before PCB layout or schematic release. The part is listed by Microchip Technology and is distributed as an application-specific clock/timing component. Current catalog pages identify inventory and ordering information, including the VSC8248KITEV-ND ordering representation used by one authorized channel. However, the listings do not expose explicit quantity-break prices in the retrieved text, so no price tier is reproduced on this page. Current sourcing, lead time, and stock status should be requested through the quote form on this page. Typical design roles for this device include clock distribution, interface timing control, communications equipment, industrial electronics, and embedded control systems. Because the exact input and output ranges are not stated in the accessible records, designers should confirm signal amplitudes, frequencies, supply requirements, I/O standards, and timing tolerances before selecting pull-up resistors, termination networks, or downstream clock devices. Those decisions must be based on the manufacturer pin description and electrical characteristics rather than assumptions based on the clock-buffer category alone. The primary design consideration is to treat VSC8248KITEV as a timing-critical component. Validate the complete clock path with worst-case loading, enable sequencing, power-up behavior, and propagation-delay variation. Review the package drawing and pin-description table during schematic capture, then preserve the manufacturer's recommended layout and decoupling guidance in the PCB implementation. If those items remain unavailable, obtain the controlled manufacturer datasheet before releasing a high-volume or safety-related design. This page consolidates the confirmed manufacturer identity, category, ordering code, current catalog sources, application context, and engineering checkpoints for VSC8248KITEV. It clearly separates confirmed information from parameters requiring manufacturer documentation, helping engineers evaluate sourcing and design readiness without presenting unverified numerical specifications as facts.

RFQ যোগাযোগ
VSC8248YJH-01 - 11.3 Gbps Quad CDR | Microchip Technology
VSC8248YJH-01

VSC8248YJH-01 - 11.3 Gbps Quad CDR | Microchip Technology

The Microchip Technology VSC8248YJH-01 is a quad-channel clock and data recovery (CDR) integrated circuit designed for 8.5 Gbps to 11.3 Gbps high-speed serial links. The device includes clock and data recovery with error detection and correction (EDC) for XFI-to-XFI+ conversion and is supplied in an orderable package identified by the YJH designator. A CDR is a high-speed line interface component that recovers a serial bit stream and its associated clock from a waveform that may have accumulated timing distortion, noise, and jitter during transmission. Positioned within clock and timing integrated circuits, the VSC8248 family supports network equipment operating at 10 Gb/s class line rates. Multiple recovered channels allow one device to serve interfaces that require parallel clock-and-data recovery rather than a single-lane retimer. The VSC8248 supports data rates from 8.5 Gbps through 11.3 Gbps. This range covers 1.25 Gb/s Ethernet, 2 Gb/s and 4 Gb/s Fibre Channel, and 2.5 Gb/s and 5 Gb/s InfiniBand applications identified in the product documentation. At the upper operating region, its 11.3 Gbps capability supports modern 10 Gb/s networking and related optical or copper transport systems without requiring a separate recovery function for each lane. The principal feature set includes four CDR channels, XFI-to-XFI+ conversion, and EDC capability. XFI provides a wide parallel data interface for transmitting serialized high-speed data, while XFI+ includes clock-forwarding information. Supporting conversion between these interface forms allows a system to bridge legacy XFI connections to newer XFI+ endpoints while recovering the transmitted clock. EDC helps correct transmission errors that may occur in the physical link. Typical deployments include 10 Gb/s Ethernet switching equipment, Fibre Channel systems, InfiniBand adapters, optical network terminals, and network interface cards. The multi-lane architecture can reduce component count in quad-port designs while centralizing clock recovery, error correction, and interface conversion. Its multi-gigabit data-rate range makes it suitable for equipment designs that must bridge protocol or physical-layer variations while maintaining a common high-speed fabric. For layout and implementation, preserve controlled-length and impedance-continuous high-speed connections, provide compliant termination and decoupling, and follow the manufacturer’s recommended reference design. Differential and high-speed clock/data paths require short return paths and careful isolation from noisy power converters. Confirm the exact YJH package dimensions, exposed-pad arrangement, pin assignments, and thermal limits against the manufacturer datasheet before releasing PCB artwork. This page combines the manufacturer product information with a practical view of protocol applications, interface considerations, sourcing options, and validated drop-in alternatives. It is intended to help engineers identify whether the VSC8248YJH-01 matches a high-speed recovery requirement before beginning board-level implementation.

RFQ যোগাযোগ
VSC8248YJH-02 - 4-Port 11.3 Gbps SFI-to-XFI CDR | Microchip
VSC8248YJH-02

VSC8248YJH-02 - 4-Port 11.3 Gbps SFI-to-XFI CDR | Microchip

The Microchip Technology VSC8248YJH-02 is a four-port clock and data recovery (CDR) application-specific IC that converts serial interface (SFI) signals into extended small form-factor pluggable (XFI) signals at data rates from 8.5 Gbps to 11.3 Gbps. The device includes integrated electronic dispersion compensation (EDC) and is packaged in a 225-FCBGA measuring 16 mm by 16 mm. A clock and data recovery IC is a timing-recovery semiconductor used in high-speed serial links to recover the transmitted clock from the data stream and regenerate a synchronized data output. In the broader hierarchy, the VSC8248 belongs to clock and timing ICs, interface ICs, and application-specific clock/timing semiconductors. Its four-port architecture allows one device to serve multiple high-speed channels while centralizing configuration and diagnostics. The principal operating capability is the supported 8.5 Gbps to 11.3 Gbps per-channel data-rate range. Four outputs support independent high-speed interface channels, while integrated EDC extends usable reach by compensating signal degradation. The manufacturer documentation also identifies programmable output and integrated diagnostics as major device features, making the IC suitable for systems where link health must be monitored during operation rather than only during manufacturing. The VSC8248YJH-02 is intended for optical and copper Ethernet infrastructure equipment operating at multi-gigabit line rates. Its SFI-to-XFI conversion function allows a system to use different serial-interface conventions on the line-card and backplane sides. The 225-FCBGA package provides a high pin count for power distribution, high-speed differential signaling, configuration, monitoring, and diagnostic functions, but it also requires a dense multilayer PCB and careful high-speed layout practices. Typical applications include Ethernet switches, routers, optical line cards, network-interface equipment, telecommunications aggregation systems, and high-speed backplane equipment. The four-channel organization can reduce the number of discrete conversion devices required in a multiport line card while providing consistent clock recovery and diagnostics across channels. Designers should preserve controlled-impedance routing for every high-speed differential pair, maintain continuous reference planes, and place decoupling and clock-support components according to the manufacturer evaluation-board layout. Because the FCBGA has a dense pitch and numerous supply connections, power and ground planes require careful partitioning to prevent coupled noise from degrading CDR margin. Production designs should also validate the complete SFI and XFI channel in the target connector, cable, optical, or backplane environment. This product page combines the verified device identity, package format, interface conversion, supported data-rate range, and EDC capability with practical PCB guidance, application guidance, and strict drop-in-replacement analysis. The component is positioned for engineers evaluating a four-port, 11.3 Gbps-capable CDR rather than a general-purpose clock generator or conventional low-speed clock buffer.

RFQ যোগাযোগ
VSC8248ZREV - 11.3 Gbps Quad CDR | Microchip Technology
VSC8248ZREV

VSC8248ZREV - 11.3 Gbps Quad CDR | Microchip Technology

Microchip Technology VSC8248ZREV is a four-channel clock and data recovery device operating from 8.5 Gbps to 11.3 Gbps. It integrates adaptive electronic dispersion compensation for high-speed optical and backplane links and is supplied in a bulk package configuration. A clock and data recovery device, commonly called a CDR, extracts a usable data stream from a high-speed serial link and recovers the associated clock. This function sits within the physical-layer hierarchy of optical communications, Ethernet, Fibre Channel, and InfiniBand equipment. By regenerating timing and signal integrity at the receiver, a CDR allows downstream circuitry to operate without directly processing the degraded waveform received over a long channel. The VSC8248ZREV provides four recovery channels, programmable input equalization, and a KR-compliant multi-tap output driver. Adaptive electronic dispersion compensation helps compensate for channel-related signal degradation. Together, these features target difficult printed-circuit-board and optical backplane channels where frequency-dependent loss, reflections, and timing distortion can impair data recovery. The device supports operation from 8.5 Gbps through 11.3 Gbps and is associated with IEEE 802.3ae, IEEE 802.3aq, SFF-8431, 8G Fibre Channel, and 10G QDR InfiniBand protocols. These protocol associations make the device relevant to 10G Ethernet, Fibre Channel, and InfiniBand signal paths, provided that the complete system timing, reference clock, and lane configuration satisfy the device requirements. Typical applications include 10G Ethernet optical-module receivers, Fibre Channel switching equipment, InfiniBand adapters, backplane equalizers, and high-speed serial retiming subsystems. In each case, the CDR can reconstruct the receive clock while equalization and dispersion compensation improve signal margin before data reaches the packet-processing or framing layer. Designers should evaluate the recovered-clock behavior, reference requirements, lane-to-lane skew, channel loss, and firmware configuration before committing a board layout. The bulk package designation indicates a shipment format rather than a surface-mount form factor, so the exact mechanical package, land pattern, pin count, and solder process must be confirmed before PCB design begins. This product overview connects protocol support, recovery bandwidth, equalization, adaptive dispersion compensation, and replacement considerations to help engineers determine whether the VSC8248ZREV fits a specific 10G-class link architecture.

RFQ যোগাযোগ
VSC8256EV - Quad 1G/10G Serial Repeater | Microchip Technology
VSC8256EV

VSC8256EV - Quad 1G/10G Serial Repeater | Microchip Technology

The Microchip Technology VSC8256EV is a quad 1G/10G serial-to-serial, protocol-agnostic repeater/retimer with hardware-based host-side-only 10GBASE-KR auto-negotiation and training. It is designed for board-level signal integrity applications requiring retiming of high-speed serial links. The device supports 10.3125 Gbps LAN mode, 9.95328 Gbps WAN mode, and 1.25 Gbps mode, according to the available VSC8256 datasheet summary. Its signal-conditioning architecture is protocol agnostic, allowing it to be used with multiple serial interfaces rather than being restricted to one specific protocol. The VSC8256 is associated with a small-form-factor, low-power FCBGA package, making it suitable for compact telecommunications and networking equipment. The VSC8256EV ordering code is listed by Microchip Technology and is available through authorized distributors and distributor marketplaces. The core engineering benefit of this component is that it combines multi-lane serial retiming with integrated 10GBASE-KR auto-negotiation and training, reducing the amount of external protocol-specific support required in board-level designs. Typical implementation areas include 10G Ethernet backplanes, serial links between cards, telecommunications equipment, and other systems where loss, skew, or jitter can compromise high-speed transmission. Engineers should confirm the exact package dimensions, pin assignments, thermal limits, and electrical characteristics against the manufacturer datasheet before layout or production release.

RFQ যোগাযোগ
VSC8256YMR - Quad 10G Repeater/Retimer | Microchip
VSC8256YMR

VSC8256YMR - Quad 10G Repeater/Retimer | Microchip

The Microchip Technology VSC8256YMR is a quad 1G/10G protocol-agnostic serial-to-serial repeater/retimer designed for board-level Ethernet signal-integrity applications. It provides four serial channels operating at 1G or 10G, integrates hardware-based host-side 10GBASE-KR auto-negotiation and training, and is associated with a low-power 256-FCBGA package. Its central function is to recover and retime high-speed serial links while supporting board-level connectivity across WAN, LAN, switching, and telecom equipment. A repeater/retimer is a signal-integrity IC positioned between two serial endpoints to reduce timing uncertainty, recover degraded signals, and extend reliable communication over circuit-board channels. Within the semiconductor hierarchy, the VSC8256YMR belongs to the serial transceiver and interface-controller class rather than the general-purpose Ethernet PHY category. This distinction matters because the device is protocol-agnostic and focuses on physical-layer signal recovery rather than converting between conventional Ethernet media and a digital host interface. The device supports four 1G/10G serial paths in one device, allowing a multiport system to use a consistent retiming architecture across parallel lanes. Its hardware-based host-side 10GBASE-KR auto-negotiation and training functions support link establishment over backplane-style electrical channels. Combining these functions in a compact FCBGA can reduce the number of separate repeater devices required in dense line-card and switching-platform designs while keeping signal timing behavior consistent among channels. The 256-FCBGA package provides a high pin count suitable for four independent high-speed channels, their associated supply and ground connections, control interfaces, and configuration or reference connections. Dense ball-pitch packaging also demands careful PCB layout, short high-speed escape paths, controlled reference planes, and independent supply-return distribution. The package is intended for surface-mount assembly and is suited to multilayer boards designed specifically for multi-gigabit signal routing rather than simple two-layer prototyping. Typical board-level uses include 10G Ethernet switching equipment, WAN and LAN interface line cards, telecom backplanes, and systems requiring protocol-independent signal recovery between endpoints. In these applications, the retimer can help compensate for connector, package, and PCB-channel losses while preserving deterministic link behavior. It is also relevant to equipment designers implementing four-lane 1G or 10G links where channel-to-channel timing consistency and training control are important design objectives. Design teams should evaluate the complete channel path rather than treating the retimer as a standalone specification. Loss and jitter budgets, transmit and receive equalization, connector transitions, reference-clock quality, power sequencing, and the PCB stack-up determine whether a 10G channel closes reliably. Decoupling and power-plane design are particularly important in a 256-ball package because each high-speed retimer channel requires clean references and controlled return paths for dependable signal recovery. This product page consolidates the manufacturer description, package information, sourcing details, application guidance, and pin-compatible family options into a concise engineering reference. It also highlights the distinction between protocol conversion, Ethernet media access, and true repeater/retimer functions to help designers select the correct device for high-speed board-level signal-integrity requirements.

RFQ যোগাযোগ
VSC8256YMR-01 - Quad 10G SFI/XFI Repeater | Microchip
VSC8256YMR-01

VSC8256YMR-01 - Quad 10G SFI/XFI Repeater | Microchip

Microchip Technology VSC8256YMR-01 is a quad-channel 1G/10G serial-to-serial repeater/retimer with four 10Gbps SFI-to-XFI channels in a 256-ball FCBGA measuring 17 x 17 mm. The device is protocol-agnostic and supports 1G and 10G operation, making it suitable for board-level Ethernet signal-integrity designs. A repeater/retimer is a signal-conditioning semiconductor that receives a high-speed serial waveform, regenerates it, and transmits a cleaner copy to the next circuit. Unlike a simple passive redriver, a retimer can recover timing through receive and transmit equalization. The VSC8256 sits within the broader hierarchy of Ethernet interface ICs, serial transceiver support ICs, and semiconductor signal-integrity devices. The VSC8256 provides four independent serial channels and integrates hardware-based, host-side-only 10GBASE-KR auto-negotiation and training. This combination allows a board designer to address difficult printed-circuit-board loss on Ethernet links while retaining compatibility with protocol-independent serial interfaces. The manufacturer describes the device as a low-power solution for board-level signal-integrity applications. Its SFI-to-XFI architecture places separate serial-side and host-side interfaces around each repeater channel. In a 10G design, the device can receive SFI traffic and provide conditioned XFI output, helping recover signal integrity across connector, package, and PCB channels. Protocol independence allows the same device to support multiple Ethernet or compatible serial-transfer arrangements rather than requiring a fixed end protocol. Typical applications include 10GBASE-KR backplanes, 10G Ethernet switches and routers, WAN and LAN interface equipment, server networking, and high-speed line cards. The four-channel architecture can reduce the number of separate retimer components required in a multiport design, while the 17 x 17 mm FCBGA supports dense board layouts requiring high pin density. The primary design consideration is that a 256-ball FCBGA requires careful PCB escape routing, power and ground distribution, and thermal analysis. Differential traces should follow the manufacturer's reference layout, and decoupling should be placed close to the supply pins. Signal-integrity performance depends on the complete channel, including connector and trace geometry, rather than on the IC alone. This page combines the manufacturer's device description with package-level sourcing information and practical selection guidance. It distinguishes the orderable MPN from the VSC8256 family designation, summarizes the confirmed four-channel architecture, and identifies the board-level considerations that matter when integrating this Ethernet retimer into a 10Gbps system.

RFQ যোগাযোগ
VSC8257EV - Quad 1G/10G Ethernet PHY | Microchip Technology
VSC8257EV

VSC8257EV - Quad 1G/10G Ethernet PHY | Microchip Technology

The Microchip Technology VSC8257EV is an evaluation platform for the VSC8257 quad 1G/10G serial-to-serial Ethernet PHY, featuring VeriTime IEEE 1588v2 network timing and support for dual-sided 10GBASE-KR in a low-power FCBGA device. The verified distributor listing identifies VSC8257EV as a telecom interface IC, while the manufacturer page describes the underlying VSC8257 PHY. The product therefore belongs to the Ethernet physical-layer and telecom-interface ecosystem rather than the general-purpose processor or memory categories. A serial-to-serial Ethernet PHY is an interface integrated circuit that converts digital data into high-speed electrical signaling for network equipment. The VSC8257 family supports 1G and 10G Ethernet links and incorporates Microchip’s VeriTime technology for IEEE 1588v2 network timing. Its dual-sided 10GBASE-KR capability, auto-negotiation, and link training make it relevant to carrier-grade, enterprise, and industrial Ethernet systems where deterministic timing and interoperable backplane links are important. The verified product information identifies four PHY channels, 1G/10G operation, serial-to-serial Ethernet operation, IEEE 1588v2 timing support, dual-sided 10GBASE-KR, auto-negotiation, training, and a low-power FCBGA implementation. These features distinguish it as a multiport network interface rather than a single-port transceiver. The available evidence does not specify lane data rates in decimal form, power consumption, clock requirements, register depth, temperature grades, or individual ball assignments. Typical VSC8257EV evaluation use includes demonstrating 10GBASE-KR links between line cards, validating network timing behavior with VeriTime, testing auto-negotiation and training across backplanes, and bringing up multiport Ethernet equipment. Engineers can use the evaluation platform to examine signal integrity, clocking, firmware, board-level routing, and interoperability before integrating the production VSC8257 device into carrier, switching, or industrial network equipment. A key engineering caution is that evaluation-board access does not guarantee a pin-for-pin production-board replacement. Confirm the exact VSC8257 package, exposed-pad requirements, reference clocks, power rails, SerDes lane assignments, connector interfaces, and thermal constraints before committing a PCB layout. The provided sources do not include the complete schematic, bill of materials, pinout, or detailed electrical characteristics. This page consolidates the verified manufacturer and distributor information, identifies where published data is unavailable, and distinguishes the VSC8257 evaluation platform from verified drop-in alternatives. It is intended to support component identification and design planning without presenting unverified package, pricing, pinout, or cross-reference claims.

RFQ যোগাযোগ