উপশ্রেণী

পণ্য (44,000+)

VSC8479YHQ-01 - 10G SFI4.1 SerDes Transceiver 195-FCBGA | Microchip
VSC8479YHQ-01

VSC8479YHQ-01 - 10G SFI4.1 SerDes Transceiver 195-FCBGA | Microchip

The Microchip Technology VSC8479YHQ-01 is a 1:16 / 16:1 multi-rate SerDes transceiver with integrated Clock and Data Recovery (CDR) and Clock Multiplier Unit (CMU), packaged in a 195-ball FCBGA measuring 12 mm x 12 mm. Operating continuously from 9.953 Gbps to 11.35 Gbps, the device supports SFI4.1 and SFI-5.1 interface standards with a 16-bit parallel datapath for 10 Gigabit Ethernet, SONET/SDH OC-192, OTN OTU2, and Fibre Channel applications. A SerDes (Serializer/Deserializer) is a mixed-signal integrated circuit that converts between parallel and high-speed serial data streams while embedding clock recovery, equalization, and line-coding functions. As a class of physical-layer (PHY) interconnect ICs, SerDes devices sit between the MAC/ASIC framer and the optical module, forming the bridge between the digital chip domain (typically LVDS/PECL parallel buses) and the analog serial optical/electrical domain. The VSC8479 family belongs to the multi-rate 10G transceiver category, which spans oversampled and bit-serial architectures for telecom and datacom line cards. Key features include integrated CDR with low-jitter performance, a reference-less or reference-clock CMU for synthesizing the line-side baud clock from a low-frequency system reference, programmable transmit pre-emphasis and receive adaptive equalization for backplane and optical reach extension, and an I2C/SPI management interface for system bring-up. The 195-FCBGA package uses controlled-collapse chip connection with flip-chip die attach, providing short electrical paths for multi-GHz signals and a thermal envelope suitable for forced-air-cooled line-card environments. Architecture-wise, the device integrates four physical lanes (per SFI4.1 direction) with 16-bit datapaths, internal AC-coupling, and on-chip termination. The 17 mm x 17 mm footprint described in vendor collateral refers to the bare die-area footprint class typical of FCBGA-195 assemblies, enabling cost and board-area reduction for SFP+/XFP module and small-form-factor line-card designs. Typical applications include 10G Ethernet SFP+ and XFP transceivers, OTN OTU2 line cards, SONET OC-192 short-reach modules, multi-rate muxponder/framer I/O, and 10G Fibre Channel host-bus adapters. Per the vendor product page, every device is tested at high speed to ensure production-grade performance. Designers should evaluate AC-coupling capacitor selection, PCB material (low-loss FR-4 or Megtron), and matched-length routing for the four differential lanes to meet SFI4.1 jitter masks. The integrated CDR reduces BOM by eliminating an external clock-recovery block. This page aggregates distributor stock, parametric drop-in alternatives, and engineering design notes that complement the Microchip datasheet and Mouser spec summary (msco-s-a0003388128-1).

RFQ যোগাযোগ
VSC8479YY - 11.3 Gbps 1:16 Transceiver | Microchip Technology
VSC8479YY

VSC8479YY - 11.3 Gbps 1:16 Transceiver | Microchip Technology

Microchip Technology VSC8479YY is a telecom interface IC implementing a 1:16 transmit and 16:1 receive transceiver with integrated clock and data recovery unit (CDR) and clock multiplier unit (CMU). The device is supplied in a 244-pin FCBGA package measuring 17 mm by 17 mm, and a listed distributor specification identifies a maximum data rate of 11.3 Gbps. Its operating frequency begins at 9.953 Gbps according to the manufacturer product description. A high-speed serial interface transceiver is a semiconductor device that converts between parallel or narrower-width data paths and high-speed serial communication links. The VSC8479YY belongs to the broader interface IC and telecommunications IC hierarchy. Integrating the transceiver, CDR, and CMU functions in one package reduces the number of separate clock-recovery and multiplexing blocks required in a multi-lane optical or backplane interconnect system. The principal functional characteristics are a 1:16 parallel-to-serial transmission ratio, a 16:1 serial-to-parallel reception ratio, integrated clock recovery, and integrated clock multiplication. These functions support systems requiring multiple high-speed lanes to be aggregated or recovered efficiently. The 11.3 Gbps data-rate capability is particularly relevant to optical transport, backplane, and other high-bandwidth telecommunications infrastructure where parallel-to-serial conversion and deterministic clocking are required. The VSC8479 architecture integrates clocking with data conversion instead of treating the CDR and CMU as independent blocks. This combination is intended to provide a comprehensive interface solution for designs that need recovered clocks, multiplied reference clocks, and bidirectional lane conversion. Exact recovery ranges, jitter specifications, reference-clock requirements, lane polarity, voltage levels, and power consumption were not included in the supplied verified records and must therefore be confirmed in the manufacturer documentation. Typical implementation areas include telecommunications equipment, optical transport modules, network switching systems, and other multi-lane serial links that require parallel-to-serial and serial-to-parallel conversion. System designers should also account for the FCBGA package requirements, including fine-pitch escape routing, multilayer PCB construction, controlled impedance, and power and ground distribution across 244 package contacts. The principal design consideration is package integration. A 17 mm by 17 mm FCBGA requires careful PCB footprint design, thermal management, and high-density routing rules. Power rails, reference clocks, high-speed differential pairs, and control interfaces should be evaluated against the manufacturer's pinout, reference design, and layout guidance before schematic or PCB sign-off. This product page combines the verified Microchip product summary, distributor package information, availability references, and practical implementation guidance. It distinguishes published VSC8479 characteristics from parameters that still require datasheet confirmation and does not treat unverified substitute parts as drop-in replacements.

RFQ যোগাযোগ
VSC8479YYY - 11.3 Gbps 16-Bit Transceiver | Microchip
VSC8479YYY

VSC8479YYY - 11.3 Gbps 16-Bit Transceiver | Microchip

The Microchip Technology VSC8479YYY is a 1:16 and 16:1 high-speed serial transceiver operating continuously from 9.953 Gbps to 11.3 Gbps, with integrated clock and data recovery, clock multiplication, and a 244-FCBGA package measuring 17 mm by 17 mm. It serves OC-192, 10GbE, and 10GFC-oriented signal-chain designs that require parallel-to-serial and serial-to-parallel conversion in one device. A high-speed transceiver is a semiconductor interface that converts wide parallel data into a high-speed serial stream and converts received serial data back into parallel form. The VSC8479 belongs to the broader transceiver and data-converter hierarchy while integrating timing-recovery functions needed to establish and recover a reliable high-speed data stream. Its 16-bit interface, continuous frequency coverage, and integrated CDR and CMU reduce the amount of external high-speed conversion circuitry required in communications equipment. Key features include a 1:16 transmit fanout, a 16:1 receive aggregation, a 16-bit parallel data path, and a documented continuous operating span of 9.953 Gbps to 11.3 Gbps. The device is identified as a single Ethernet-class port transceiver by Mouser and as a telecom IC transceiver by DigiKey. Its single-chip, 17 mm by 17 mm implementation is specifically presented as a way to reduce board area and system cost in compact, price-sensitive modules. The integrated clock and data recovery unit supports extraction or recovery of timing from the associated high-speed signal path, while the clock multiplier unit supplies the required derived clock functions. This integration can simplify synchronization architecture, but board implementation still requires careful high-speed layout, controlled impedance, short return paths, compliant clocking, power delivery, isolation, and signal-integrity verification. Exact power, voltage, pin, and environmental limits must be confirmed in the manufacturer datasheet before layout release. Typical uses include 10GbE and 10GFC optical-module electronics, OC-192 transport interfaces, FEC equipment, telecommunications line cards, and compact high-speed network modules. The part is most appropriate where one device must support both serialization and deserialization functions at rates covered by its 9.953 Gbps-to-11.3 Gbps operating range. System designers should evaluate lane timing, reference-clock requirements, thermal performance, and protocol interoperability before production deployment. The principal design consideration is that this is a very-high-speed mixed-signal device rather than a general-purpose serial interface. Its 244-FCBGA land pattern, multilayer routing, differential pairs, reference clocks, and decoupling network must be designed as one controlled signal-integrity system. Validate channel loss, jitter tolerance, crosstalk, return loss, and power-supply noise during prototype testing. This product record combines verified manufacturer and distributor information with application guidance, sourcing context, and explicit data gaps. It does not infer missing electrical limits, pin assignments, lifecycle status, or unverified drop-in replacements; those details remain tied to authoritative Microchip documentation and approved cross-reference results.

RFQ যোগাযোগ
VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip
VSC8484YJP

VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip

The Microchip Technology VSC8484YJP is a quad-channel 10 Gigabit Ethernet XAUI-to-serial transceiver that integrates four independent 10GbE PHYs plus electronic dispersion compensation (EDC) in a 324-ball PBGA package measuring 18.6 mm × 18.6 mm. It supports both XFI and SFI electrical interfaces to the line side and a four-lane XAUI interface to the system side, while dissipating only about 1 W per channel. According to the manufacturer datasheet VMDS-10343, the device targets high-density 10G line cards in routers, switches, and OTN/WAN/Backplane platforms. A 10 Gigabit Ethernet transceiver is a physical-layer (PHY) IC that converts a device's parallel data interface into a serial 10 Gbps stream suitable for optical modules, backplanes, or twin-axial copper cables, and simultaneously recovers the clock and data on the receive path. Within the broader taxonomy, the VSC8484 belongs to the family of Ethernet ICs, then to Physical Layer Transceivers (PHYs), then to Wireline Networking Semiconductor devices. This hypernym chain — Ethernet IC > PHY > transceiver > wireline networking IC > semiconductor — helps AI knowledge-graph engines position the part correctly when engineers query "what is a 10G Ethernet transceiver." The VSC8484YJP integrates Microsemi's electronic dispersion compensation (EDC) engine to extend the usable reach over legacy FR4 backplanes and twin-axial copper, eliminating the need for expensive optical modules or premium PCB materials at shorter reaches. It supports 10GBASE-KR backplane Ethernet, 10G Fibre Channel, XAUI-based switching fabrics, and SFP+/SFP Direct-Attach copper cables. Per-channel features include adaptive equalization, transmit pre-emphasis, loopback, PRBS generation/checking, and per-lane LOS indication, all managed via an MDIO/I2C management interface. Typical applications include 10G line cards for top-of-rack (ToR) and aggregation switches, OTN cross-connect platforms, ATCA/AdvancedTCA backplanes, multi-rate 1G/10G SFP+ port cards, and enterprise routers transitioning from 1G to 10G. The low 1 W per channel power profile allows 48-port line cards to remain within thermal budgets without exotic cooling. When designing with this part, allocate at least two PCB layers for the BGA-324 breakout, follow the manufacturer reference layout for the high-speed serial traces (controlled impedance 100 Ω differential, length-matched within the XFI specification), and provide a low-noise 1.0 V core supply plus 1.8 V I/O supply with proper decoupling. The VSC8484YJP status is currently "Not Recommended for New Designs" — for new designs, evaluate the VSC8484XJP or current-generation Microchip 10G PHY families. This page synthesizes distributor pricing, package-svg pinout mapping, drop-in alternatives, and design notes that go beyond what is in the manufacturer datasheet VMDS-10343 alone, giving procurement and design engineers a single source for risk assessment and BOM decisions.

RFQ যোগাযোগ
VSC8487YJU - 10GbE Ethernet Transceiver | Microchip Technology
VSC8487YJU

VSC8487YJU - 10GbE Ethernet Transceiver | Microchip Technology

The Microchip Technology VSC8487YJU is a 10GbE Ethernet backplane transceiver that converts between a single XFI serial interface and dual XAUI lanes. It is packaged for high-speed printed-circuit-board designs and combines EDC, KR support, and IEEE 1588v2 timing functionality for timing-critical Ethernet systems. The lead-free construction is identified explicitly for the related VSC8487YJU-15 ordering code. An Ethernet transceiver is an interface IC that connects a digital communications system to a physical transmission medium. XFI and XAUI are high-speed serial interfaces commonly used to move 10GbE traffic across boards, backplanes, chassis, and equipment interconnects. A device that translates XFI to dual XAUI can bridge a narrow serial-side connection to two parallel high-speed lanes while centralizing electrical signaling, clocking, and timing functions in one component. Key features include support for 10GbE operation, EDC and KR, dual XAUI connectivity, and IEEE 1588v2 timing compliance. These capabilities make the VSC8487 family relevant to synchronized networking equipment, Ethernet switching systems, industrial automation platforms, and test equipment that requires deterministic traffic timing. The exact electrical ratings, operating temperature, and package dimensions should be confirmed against the manufacturer datasheet before release to production. The VSC8487 belongs to Microchip’s family of dual-channel XAUI-to-serial transceivers. The manufacturer identifies VSC8487-15 and VSC8488-15 as timing-oriented devices supporting industry-standard protocol encapsulations. This positioning places the VSC8487YJU within the broader hierarchy of Ethernet interface IC, network interface controller, data-converter semiconductor, and communication IC. Typical applications include 10GbE switching equipment, backplane routing systems, industrial control networks, synchronized test and measurement platforms, and telecommunications infrastructure. EDC helps the receiver recover data impaired by interconnect loss, while KR support addresses known backplane signal-integrity challenges. IEEE 1588v2 compliance is especially useful when synchronized time or deterministic event ordering must be maintained across the network. PCB implementation requires careful high-speed layout practices, including controlled impedance, short differential connections, suitable return paths, and compliance with the manufacturer’s reference design and decoupling guidance. Clocking, reference circuitry, reset behavior, and device configuration must follow the datasheet because incorrect sequencing or an unsuitable reference implementation can impair link operation even when the device itself is functioning correctly. This page organizes the VSC8487YJU’s confirmed networking capabilities, timing features, ordering variants, and practical design implications. It also separates documented facts from parameters that require direct confirmation, helping engineers assess fit, establish pin-compatible sourcing options, and plan robust 10GbE backplane implementations before schematic release.

RFQ যোগাযোগ
VSC8488XJU Dual-Channel XAUI Transceiver | Microchip
VSC8488XJU

VSC8488XJU Dual-Channel XAUI Transceiver | Microchip

The Microchip Technology VSC8488XJU is a dual-channel XAUI-to-serial transceiver interface IC designed for timing-critical telecommunications and data-networking equipment. Microchip identifies the VSC8487-15 and VSC8488-15 devices as fully IEEE 1588v2-compliant solutions supporting industry-standard protocol encapsulations. The VSC8488XJU is supplied in a surface-mount package and is identified by the XJU ordering suffix. An XAUI-to-serial transceiver is an interface semiconductor that converts XAUI parallel signaling into high-speed serial lanes and, in a dual-channel implementation, supports two independent signal paths. This type of device belongs to the communications interface hierarchy: serial transceiver → XAUI interface → telecommunications interface IC → semiconductor. It is used where timing, protocol synchronization, and reliable high-speed data transfer are central to the equipment architecture. The principal product-level benefits identified by Microchip are full dual-channel operation, IEEE 1588v2 compliance, support for timing-critical applications, and compatibility with industry-standard protocol encapsulations. These characteristics make the device suitable for transport, aggregation, switching, timing, and test equipment designed around XAUI links. Exact lane rates, electrical limits, clocking requirements, supply voltages, pin assignments, and package dimensions must be confirmed in the manufacturer datasheet before schematic or PCB implementation. VSC8488XJU is most relevant to systems requiring two XAUI channels and deterministic timing behavior. The IEEE 1588v2 capability supports precision time protocols, while protocol-encapsulation support can simplify interoperability with established telecommunications data paths. Its two-channel architecture can also reduce component count compared with separate single-channel transceivers when the host PCB has sufficient routing, power, thermal, and signal-integrity resources. The main design considerations are high-speed differential-routing discipline, compliant clock distribution, reference-plane continuity, controlled impedance, and careful separation between sensitive clock paths and noisy digital or power-conversion sections. Follow the manufacturer’s recommended decoupling, layout, and test procedures exactly. Confirm that the PCB footprint, pin assignment, solder-process limits, and absolute maximum ratings match the exact XJU package before releasing a production design. This page combines the manufacturer’s VSC8488 family positioning with package, procurement, comparison, and design guidance for engineers evaluating the VSC8488XJU in dual-channel XAUI systems.

RFQ যোগাযোগ
VSC8488YJU - 10GbE Dual-Channel XAUI Transceiver | Microchip
VSC8488YJU

VSC8488YJU - 10GbE Dual-Channel XAUI Transceiver | Microchip

The Microchip Technology VSC8488YJU is a dual-channel, 10 GbE XAUI-to-serial transceiver designed for timing-critical backplane, switching, and telecommunications equipment. Each channel supports 10 Gb/s serial signaling, and the device supports IEEE 1588v2 timing features for deterministic network synchronization. The component is supplied in a 196-FCBGA package measuring 15 mm by 15 mm. An XAUI transceiver is an interface IC that converts a parallel XAUI data stream into a high-speed serial lane and recovers the parallel stream on the receive side. It belongs to the serial communication transceiver hierarchy, which includes SerDes devices, physical-layer transceivers, network interface controllers, and broader communications semiconductors. Such devices move parallel data across printed circuit boards, backplanes, chassis, and rack-to-rack links. The VSC8488-15 family is identified by Microchip as a dual-channel XAUI-to-serial transceiver supporting 1588v2 compliance and industry-standard protocol encapsulations. Two integrated channels can reduce component count on systems that require parallel transmit and receive paths. The device also supports external clocking and reference arrangements for synchronization-sensitive infrastructure, although the complete clocking configuration must follow the manufacturer datasheet and reference design. At the physical layer, the VSC8488YJU combines differential high-speed serial I/O with digital control, configuration, clocking, and fault-management functions. Differential signaling improves common-mode noise rejection, while low-jitter clock distribution is important when the transceiver participates in synchronized Ethernet traffic. Board-level implementation requires controlled-impedance routing, short matched differential pairs, solid reference planes, and carefully positioned decoupling. Typical uses include 10GbE switching line cards, router and gateway interfaces, telecommunications aggregation equipment, optical-module host interfaces, network timing systems, and test equipment. In each case, the device serves as the high-speed electrical interface between parallel fabric or processing logic and narrow serial links. System architects should confirm lane count, protocol encapsulation, reference-clock requirements, and board-management features against the ordered device variant. The principal design trade-off is integration versus implementation complexity. A dual-channel transceiver consolidates two high-speed interfaces in one BGA, but it demands careful power-plane planning, thermal management, and BGA assembly control. Use the Microchip reference design and datasheet power-up sequence rather than relying on generic SerDes power rails. This page organizes the device data into a specification summary, application guidance, package information, and a practical selection comparison with closely related Microchip transceiver variants. It highlights board-level constraints that are not apparent from the MPN alone and distinguishes device variants that can look interchangeable in distributor catalogs.

RFQ যোগাযোগ
VSC8489YJU - 10G Ethernet Transceiver | Microchip Technology
VSC8489YJU

VSC8489YJU - 10G Ethernet Transceiver | Microchip Technology

The Microchip Technology VSC8489YJU is a 10G Ethernet transceiver interface controller in a 196-FCBGA (15 x 15 mm) surface-mount package. The device belongs to the VSC8489, VSC8490, and VSC8491 family of single-port and dual-port 10G Ethernet transceivers designed for electrical backplane and optical module host-card applications. Its stated application coverage includes SFP+ SR, LR, ER, and ZR fiber modules with EDC support. A 10G Ethernet transceiver interface IC is a semiconductor that connects a host controller or digital processing system to high-speed copper or optical-module interfaces. It sits between the board-level digital logic and a network-facing medium, supporting Ethernet signal generation, reception, clocking, and control through an interface such as SPI. This makes it part of the broader hierarchy of network interface controllers, Ethernet interface ICs, and telecommunications semiconductors. The VSC8489 family is designed around 10 Gigabit Ethernet data rates for backplane and optical host-card designs. Listings for the related VSC8489YJU-02 identify the device as a dual 10G reduced XAUI to XFI/SFI PHY in the same 196-FCBGA package, while VSC8489YJU-16 is identified as a single-port 10G PHY. The VSC8489YJU is therefore positioned for board designs that require a dedicated high-speed Ethernet transceiver front end rather than a general-purpose microcontroller I/O. Microchip describes the VSC8489 family as a highly flexible solution for electrical backplane and optical module host-card applications. That positioning is significant because these systems require separate transmit and receive signal paths, low-latency data transfer, and host configuration over a serial control interface. Product descriptions for related variants also identify RoHS 3 compliance and a surface-mount implementation. Typical uses include 10G SFP+ line-card designs, optical transceiver host cards, electrical backplane equipment, telecom aggregation systems, and high-speed data-processing infrastructure. In these applications, the transceiver provides the physical-layer interface between the host FPGA or ASIC and the network medium, while the surrounding processor handles packet processing and system management. When planning a PCB layout, use the manufacturer's pin-description table and package drawing for all 196 ball assignments, differential routing, supply decoupling, and exposed-connection requirements. Because the package is a large fine-pitch FCBGA, high-speed signal integrity and power distribution are as important as the nominal transceiver specifications. This page consolidates the manufacturer product-family information, distributor package and interface details, practical placement guidance, and a comparison of documented VSC8489 ordering variants. It is intended to accelerate initial design review while keeping pin-level implementation decisions tied to the official Microchip documentation.

RFQ যোগাযোগ
VSC8489YJU-10 - Dual 10G R-XAUI PHY | Microchip Technology
VSC8489YJU-10

VSC8489YJU-10 - Dual 10G R-XAUI PHY | Microchip Technology

The Microchip Technology VSC8489YJU-10 is a dual-port 10G Ethernet transceiver with reverse XAUI interface support and Premium 1588 capability, supplied in the YJU package. It belongs to the VSC8489, VSC8490, and VSC8491 family of single-port and dual-port 10G Ethernet transceivers created for electrical-backplane and optical-module host-card applications. A 10G Ethernet transceiver is a physical-layer interface IC that converts high-speed parallel or serial data into signals suitable for copper backplanes or optical-module host cards. Within the networking hierarchy, the VSC8489YJU-10 belongs to Ethernet interface controllers, which sit between a host or line-card controller and the physical communication medium. Its dual-port architecture allows two 10G links to be handled within one transceiver package. The primary product features include support for dual 10G channels, reverse XAUI operation, and Premium 1588 functionality. The reverse XAUI capability is particularly relevant to electrical-backplane designs because it helps address signal-integrity constraints associated with long, high-speed copper paths. Premium 1588 support extends the device's timing-oriented feature set for demanding synchronization requirements. The VSC8489YJU-10 is designed around the requirements of modern 10G Ethernet infrastructure rather than general-purpose serial connectivity. Its family-level positioning includes SFP+ SR, LR, ER, and ZR fiber applications, along with electrical-backplane and optical-module host-card environments. This makes it most applicable where a designer needs a compact multi-lane Ethernet physical-layer solution rather than a general-purpose interface converter. Typical use cases include 10G Ethernet line cards, optical-module host cards, switching and routing equipment, network interface appliances, and backplane-based telecommunications systems. In these systems, the transceiver can interface an Ethernet controller with external PHY components or copper connectivity while preserving a common 10G family architecture. System partitioning still depends on the selected media, reach, connector, optical, and line-card implementation. PCB implementation should prioritize short, controlled-impedance connections, solid reference planes, and compliant power distribution because the device operates in high-speed multi-lane Ethernet environments. Decoupling, clocking, lane assignment, and connector or module integration must follow the electrical requirements in the Microchip VSC8489 datasheet and the applicable host-card design guidance. This product page consolidates the verified family positioning, same-manufacturer functional equivalents, application context, and engineering selection considerations into one reference. It also distinguishes documented product identity from details that require confirmation in the full manufacturer datasheet before schematic release or PCB sign-off.

RFQ যোগাযোগ
VSC8489YJU-13 - Dual 10G Ethernet PHY | Microchip
VSC8489YJU-13

VSC8489YJU-13 - Dual 10G Ethernet PHY | Microchip

The Microchip Technology VSC8489YJU-13 is a dual 10G Ethernet transceiver PHY with two 10-gigabit channels, reverse XAUI support, and premium IEEE 1588 timing support. The device is identified by the YJU ordering code and is designed for electrical-backplane and optical-module host-card applications. It belongs to the VSC8489, VSC8490, and VSC8491 family of single-port and dual-port 10G Ethernet transceivers. An Ethernet PHY is the physical-layer interface between a communications controller or host and physical interconnect media. Within the network-interface hierarchy, a PHY connects a MAC or host controller to copper backplanes, optical-module electrical interfaces, or other high-speed lanes. The VSC8489YJU-13 operates at 10 Gb/s per channel and provides two channels, making it useful where dual-lane throughput, serial-lane equalization, and synchronized timing are required. The principal product identifiers are dual-channel 10G operation, reverse XAUI capability, and premium IEEE 1588 support. The manufacturer describes the VSC8489 family as a flexible solution for electrical-backplane and optical-module host cards. The family also targets SFP+ SR, LR, ER, and ZR fiber applications, including configurations that use electronic dispersion compensation. These capabilities make the PHY relevant to high-speed line cards, optical-module hosts, and timing-sensitive network equipment. VSC8489YJU-13 is the premium 1588 ordering option in the VSC8489YJU family. Functionally, the device combines Ethernet physical signaling, high-speed serial-lane interfacing, clocking or recovery functions, and synchronization features in one communications IC. This integration reduces the amount of discrete high-speed interface circuitry required around a network controller, while preserving a standardized modular interface for optical modules and backplane links. Typical applications include 10G Ethernet backplane equipment, SFP+ optical-module host cards, dual-port networking equipment, line cards, and test systems requiring precise network timing. IEEE 1588 functionality is particularly relevant when equipment must transfer time or event information across a packet network. Optical implementations can use the VSC8489 family with compatible SR, LR, ER, or ZR optics, while the electrical PHY provides the host-side interface to the module. Board design requires careful high-speed signal-integrity work. Differential pairs should use a controlled impedance stack-up, continuous reference planes, short return paths, and manufacturer-recommended connector or module interface layouts. Power sequencing, supply filtering, thermal management, and synchronization-clock integrity should be evaluated together because these factors can affect the margin of a 10 Gb/s interface. This page combines the manufacturer family description, distributor identification, ordering-code relationships, and practical implementation guidance for engineers evaluating the VSC8489YJU-13. It also distinguishes the documented dual 10G, reverse-XAUI, and premium IEEE 1588 features from parameters that must be confirmed in the manufacturer datasheet before a PCB or qualification decision is finalized.

RFQ যোগাযোগ
VSC8490EV - Dual-Port 10G Ethernet Eval Board | Microchip
VSC8490EV

VSC8490EV - Dual-Port 10G Ethernet Eval Board | Microchip

The Microchip Technology VSC8490EV is an evaluation platform associated with the VSC8490, a dual-port 10G Ethernet transceiver designed for electrical backplane and optical module host-card applications. The available product information identifies two 10G Ethernet ports, XFI/SFI-to-(R)XAUI signal conversion, and support for IEEE 1588 and MACsec within the VSC8490 transceiver family. The VSC8490EV package type, exact connector arrangement, and electrical limits are not published in the supplied manufacturer and distributor records, so they remain designated as data needed rather than inferred. A 10G Ethernet transceiver is a high-speed communications semiconductor that converts between serial network interfaces and parallel or widebus internal data paths. Within the broader hierarchy, the VSC8490 belongs to Ethernet physical-layer interfaces, interface controllers, network semiconductors, and integrated circuits. Its dual-port architecture allows two high-speed links to be evaluated on one hardware platform, which is useful when developing backplane equipment or optical module host cards. The VSC8490 family description specifically identifies XFI/SFI inputs and (R)XAUI outputs. XFI and SFI are serial interface formats commonly used between Ethernet line cards and optical modules, while (R)XAUI provides a widebus electrical interconnect suitable for backplane and chassis-oriented designs. The same source identifies compatibility work for SFP+ SR, LR, ER, and ZR fiber applications and describes EDC compensation as part of the family feature set. The family also provides IEEE 1588 timing support and MACsec functionality. IEEE 1588 capability is relevant to systems requiring synchronized network timing, while MACsec is the IEEE security mechanism for protecting Ethernet frames against unauthorized injection and eavesdropping. These capabilities make the evaluation platform relevant to precise timing, secure networking, line-card development, and optical transport prototyping. VSC8490EV is suitable for laboratory evaluation of dual-port 10G Ethernet links, optical module host cards, electrical backplane prototypes, SFP+ interface development, and secure network equipment. Engineers should confirm the board’s physical connectors, supported electrical standards, reference clock requirements, power input, operating temperature, and programming interface against the complete manufacturer documentation before using it in a production design. This page consolidates the verified manufacturer description, distributor inventory information, family-level interface details, sourcing links, and explicit engineering gaps for the VSC8490EV. It distinguishes documented facts from unavailable specifications so procurement and hardware teams can assess the evaluation board without mistaking unreported board details for guaranteed capabilities.

RFQ যোগাযোগ
VSC8490YJU-13 Dual 10G Ethernet PHY | Microchip
VSC8490YJU-13

VSC8490YJU-13 Dual 10G Ethernet PHY | Microchip

Microchip Technology VSC8490YJU-13 is a dual-port 10G Ethernet transceiver PHY designed for electrical backplanes and optical-module host-card applications. It provides dual 10G (R)-XAUI interfaces, premium IEEE 1588 support, and MACsec capability in a 196-FCBGA package measuring 15 mm by 15 mm. The device belongs to the VSC8489, VSC8490, and VSC8491 family of single-port and dual-port 10G Ethernet transceivers. A 10G Ethernet transceiver PHY is the physical-layer component in a high-speed network link. It converts serial data into electrical signaling for a backplane or optical-module host interface while providing the physical encoding, clocking, and control functions needed by a 10 Gb/s Ethernet system. Within the network hierarchy, the PHY sits beneath the Ethernet MAC and above the physical interconnect, where signal integrity, equalization, timing, and board-level implementation become central design considerations. The principal differentiators of the VSC8490YJU-13 are its dual-port 10G configuration, dual reversed X-AUI interfaces, premium 1588 capability, and MACsec support. Reversed X-AUI provides a high-speed parallel electrical interface suitable for demanding connectivity equipment. Premium 1588 functionality addresses systems requiring enhanced precision time measurement, while MACsec support targets secure Ethernet data-plane designs that require hardware-assisted protection. The VSC8490 family is specifically positioned for electrical backplane and optical module host card implementations. This makes the device applicable to network interface equipment that must bridge internal high-speed processing electronics with external 10G Ethernet interfaces. The dual-port arrangement can also support paired links in redundant or multi-port architectures when the surrounding system provides suitable clocking, signal conditioning, power delivery, and thermal-management resources. Typical applications include 10G Ethernet line cards, switch and router interface modules, optical transceiver host cards, server network-interface equipment, and industrial communication platforms. The product family is designed to support SFP+ SR, LR, ER, and ZR optical-module use cases, although optical performance also depends on the selected module, host electrical design, loss budget, and connector implementation. The 196-FCBGA package makes high-density multilayer layout and careful power delivery essential. Use the manufacturer pin-description table and reference design when assigning every ball, supplying rails, and routing high-speed differential pairs. Preserve controlled-length and differential-impedance relationships, minimize layer transitions, provide adjacent return-path references, and isolate sensitive clocks from noisy switching circuitry. This page combines the verified product identity, package information, Ethernet capabilities, sourcing guidance, and engineering-oriented application analysis. It also distinguishes confirmed replacement options from unverified package or suffix variants, helping engineers make a safer footprint and lifecycle decision before committing a 196-FCBGA design to production.

RFQ যোগাযোগ
VSC8490YJU-17 - Dual-Port 10GbE PHY XFI/SFI to XAUI | Microchip
VSC8490YJU-17

VSC8490YJU-17 - Dual-Port 10GbE PHY XFI/SFI to XAUI | Microchip

The Microchip VSC8490YJU-17 is a dual-port 10 Gigabit Ethernet PHY/transceiver from the VSC8489/VSC8490/VSC8491 family, supporting XFI/SFI to (R)XAUI conversion with integrated 1588 timestamping and MACsec (IEEE 802.1AE) hardware acceleration. The device is supplied in a 196-pin FCBGA (15x15 mm) package and operates from 1.0 V / 1.2 V supplies, targeting high-density 10G line cards, electrical backplanes, and SFP+/QSFP+ host-side interface applications. What is a 10G Ethernet PHY/transceiver? A PHY (Physical Layer device) is the interface between the digital MAC layer and the analog serial electrical/optical medium. Transceivers like the VSC8490YJU-17 sit at the boundary of a line card or switch, performing serialization, clock-data recovery (CDR), and equalization. The VSC8490YJU-17 additionally integrates MACsec line-rate encryption and IEEE 1588 hardware timestamping, which makes it a "secure PHY" rather than a bare transceiver. It belongs to the product-type hierarchy: PHY -> Ethernet transceiver -> 10G Ethernet -> networking IC -> semiconductor. Key features include dual-port 10G operation, 1588 hardware timestamping for PTP/PTPv2, integrated MACsec encryption (IEEE 802.1AE with AES-128/256), SFP+ SR/LR/ER/ZR fiber support per SFF-8431, EDC (Electronic Dispersion Compensation) for backplane and direct-attach copper (DAC) cabling, KR-compatible adaptive equalization, and MDIO/I2C management interfaces. SPI management is supported for host configuration. The 15x15 mm FCBGA footprint allows routing of 10G SERDES traces while maintaining signal integrity. Architecturally, the VSC8490YJU-17 uses Microchip's proven mixed-signal SERDES core with adaptive equalization, baseline-wander correction, and low-jitter PLL synthesis to meet IEEE 802.3ae 10GBASE-R compliance. Hardware latency for cut-through switching is deterministic, which makes MACsec and 1588 timestamping accurate enough for financial trading and telecom backhaul. Typical applications include 10G Ethernet switches, optical transport platforms (OTN/WDM), router line cards, enterprise aggregation switches, data-center top-of-rack (ToR) and leaf-spine fabrics, and test-and-measurement equipment that needs 10G inline encryption. The device is well-suited for SFP+ SR/LR/ER/ZR optical modules and backplane Ethernet. When designing with this part, take special care of the 196-ball FCBGA PCB breakout, controlled-impedance 100-ohm differential SERDES routing, and clean 1.0 V / 1.2 V power rails. Reference Microchip application note guidance for MACsec key-management integration and 1588 grandmaster configuration. This page consolidates distributor pricing, drop-in alternative review, and practical design considerations not contained in the manufacturer datasheet.

RFQ যোগাযোগ
VSC8490YJU-17P Dual-Port 10GbE PHY | Microchip
VSC8490YJU-17P

VSC8490YJU-17P Dual-Port 10GbE PHY | Microchip

The Microchip VSC8490YJU-17P is a dual-port 10 Gigabit Ethernet PHY transceiver from the VSC8489/8490/8491 family, supplied in a 196-pin FCBGA (15x15 mm) package. It interfaces a 10GbE host-side XFI/SFI or RXAUI backplane connection to two SFP+/10GBASE-R PHY lanes, supporting SFP+ SR/LR/ER/ZR fiber modules and EDC-corrected electrical backplane links. The device integrates 1588 Timing-over-Ethernet hardware timestamping and IEEE 802.1AE MACsec link-layer encryption, making it a flexible SerDes + PHY building block for carrier-grade Ethernet equipment. What is a 10GbE PHY? A PHY (Physical Layer device) is the lowest layer of the OSI networking stack. It converts digital MAC-layer data into analog signals suited to copper traces, direct-attach cables, or optical modules. The VSC8490YJU-17P belongs to the SERDES / Ethernet PHY / telecom interface IC family within Microchip's networking portfolio, sitting beneath the MAC and above the physical medium. Modern 10GBASE-R PHYs also integrate MACsec encryption and IEEE 1588 timestamping, which is why the VSC8490 is described as an XFI-to-(R)XAUI MACsec/1588 dual-port transceiver rather than as a plain PHY. Key features of the VSC8490YJU-17P include dual 10G lanes, integrated MACsec, 1588v1/v2 hardware timestamping, SFI/XFI host-side interface, (R)XAUI backplane support, SFP+ SerDes with adaptive equalization, and EDC (Electronic Dispersion Compensation) for KR-style backplane operation. Core supply voltages are 1.0V and 1.2V as documented on the Arrow listing, and the device uses an SPI management interface for register access. The VSC8490 architecture is built around independent per-lane SerDes cores with adaptive equalization, a 1588 timestamp engine, and a MACsec engine using AES-GCM-128 with support for 16+ SA contexts. Internal firmware-configurable equalization allows the same silicon to be tuned for short-reach copper and long-reach optical modules, simplifying SKU management across host-card designs. The MACsec block offloads per-packet encryption from the host CPU/ASIC, which is essential for backplane and metro Ethernet platforms where line-rate 10G encryption cannot burden the main processor. Typical applications for the VSC8490YJU-17P include 10G Ethernet switches and routers, OTN/WDM transport equipment, optical transport platforms with MACsec-secured links, top-of-rack and carrier-grade switches, and high-speed backplane line cards in routers and base stations. It is also used in SFP+ media-converter modules and 10G-to-fiber test gear. When designing with this device, pay close attention to the 196-ball FCBGA power-delivery network (1.0V/1.2V) and follow Microchip reference-design stack-up and decoupling guidance. Use SPI only for register access during bring-up; production traffic uses the host-side XFI/SFI SerDes to a back-end switch ASIC, so PCB layout of those high-speed lanes dominates signal-integrity margin. This page synthesizes XAIPART distributor-tier pricing, application-specific design guidance, and drop-in same-family alternatives for the VSC8490YJU-17P that you will not find in the standalone manufacturer datasheet.

RFQ যোগাযোগ
VSC8492YJD-12 - 10GbE PHY with OTN-FEC | Microchip
VSC8492YJD-12

VSC8492YJD-12 - 10GbE PHY with OTN-FEC | Microchip

The Microchip Technology VSC8492YJD-12 is a four-channel Ethernet physical-layer transceiver supporting 6.25 Gb/s and 10 Gb/s per channel, with OTN-FEC capability, in a 484-pin FCBGA package measuring 23 mm by 23 mm. It is designed for high-performance networking equipment requiring dense, multichannel Ethernet connectivity. An Ethernet PHY is an interface integrated circuit that converts digital data into physical-layer signals for transmission over copper or optical network media and recovers signals at the receiving endpoint. Within the product hierarchy, the VSC8492YJD-12 belongs to the Ethernet physical-layer transceiver class, then to the broader network interface IC and semiconductor categories. Its integrated FEC function supports optical-transport networking designs that require reliable high-speed links. The four-channel architecture allows one device to address multiple 10GbE links while reducing the number of physical interface components required on a communications board. Support for both 6.25 Gb/s and 10 Gb/s operation provides flexibility for line systems operating at different rates. The listed serial, SFI, and XFI interfaces connect the PHY to an FPGA, ASIC, line card, or other digital processing element. OTN-FEC integration provides a dedicated error-management function for optical transport links. A 484-pin FCBGA provides a substantial number of high-speed connections and power-distribution pins in a relatively compact 23 mm by 23 mm surface-mount footprint. This dense package is appropriate for multilayer boards that can preserve controlled-impedance routing for high-speed differential interfaces. Because the package has a large ball array and many signal connections, PCB escape routing, layer transitions, return-path continuity, and thermal management require deliberate planning rather than a simple two-layer layout. Typical uses include 10GbE line cards, optical transport equipment, Ethernet aggregation systems, network-interface modules, and FPGA-based communication platforms. In an optical-transport design, the PHY can pair with a high-speed FPGA or ASIC and optical modules while using FEC to protect the physical link. In copper-based systems, the same multichannel PHY can reduce the number of PHY devices needed for dense line-card implementations, subject to the electrical requirements of each medium. The principal design consideration is signal integrity. Keep high-speed differential routes short and impedance controlled, provide continuous reference planes, minimize stub branches, and place required decoupling and termination close to the device. Thermal and power integrity are equally important because a 484-pin BGA concentrates power and signal connections into a compact area. Use the manufacturer’s pin-description table, recommended decoupling network, and high-speed layout guidance when assigning the board netlist. This product summary consolidates the Ethernet PHY function, channel count, supported line rates, OTN-FEC feature, package dimensions, and practical PCB considerations into a design-focused reference. It also distinguishes verified device facts from specifications that still require confirmation during component qualification and schematic review.

RFQ যোগাযোগ
VSC8492YJD-13 - Dual/Quad 10GbE PHY | Microchip
VSC8492YJD-13

VSC8492YJD-13 - Dual/Quad 10GbE PHY | Microchip

The Microchip Technology VSC8492YJD-13 is a dual/quad 10GbE universal physical-layer interface IC with OTN forward-error correction, supported through Serial, SFI, and XFI interfaces, and housed in a 484-FCBGA package measuring 23 mm by 23 mm. It is intended for high-speed telecommunications and networking equipment where 10 Gigabit Ethernet links must interface with carrier-grade transport systems. A universal PHY is a semiconductor that adapts a high-speed serial data stream between a transceiver or optical module and a digital line card. In the broader hierarchy, this device belongs to the Ethernet interface IC family, then to network interface ICs, interface ICs, and integrated circuits. Its combination of 10GbE operation, multiple high-speed serial interfaces, and OTN FEC support places it between physical-layer signaling and transport-error management. The principal feature set includes support for dual or quad 10GbE Universal PHY operation, Serial, SFI, and XFI connectivity, and OTN FEC capability. This allows a line card designer to consolidate multiple high-speed lanes while retaining a path for forward-error correction in optical transport designs. The 484-FCBGA package provides the high-density interconnect needed for a device integrating numerous high-speed, power, control, and configuration signals. Technically, the device is positioned for line-card and optical-network-interface designs where serial signaling integrity, transport overhead, and recovery mechanisms matter. Its interface selection supports adaptation to different optical-module architectures, while the FEC function targets transport links that require protection against transmission errors. The manufacturer identifies the part as a telecom Ethernet interface rather than a general-purpose Ethernet PHY, indicating that designers should follow its reference interfaces and layout guidance closely. Typical uses include 10GbE line cards, SFI- and XFI-based optical modules, telecom Ethernet switching systems, OTN transport equipment, and dual/quad-port network interface assemblies. In these systems, the VSC8492YJD-13 can terminate high-speed serial lanes, coordinate the Ethernet physical layer, and provide OTN FEC functions when the surrounding optical and digital architecture requires them. Design considerations center on high-speed signal integrity, power sequencing, thermal performance, and exact PCB footprint compatibility. Differential routing, return-path continuity, controlled impedance, and close placement of decoupling and clock circuitry are essential because this device supports 10GbE-class interfaces. The 23 mm by 23 mm FCBGA also requires careful escape-routing and assembly planning, including thermal-via placement beneath the device. This product page combines the verified 10GbE, interface, FEC, circuit-count, and FCBGA characteristics with package-focused implementation guidance, sourcing workflows, application analysis, and a strict compatibility review that distinguishes true pin-to-pin replacements from merely similar Ethernet interface devices.

RFQ যোগাযোগ
VSC8494YJE-12 - Dual/Quad 10GE PHY | Microchip Technology
VSC8494YJE-12

VSC8494YJE-12 - Dual/Quad 10GE PHY | Microchip Technology

The Microchip Technology VSC8494YJE-12 is a high-performance Ethernet interface IC described as a dual/quad 10GE PHY with OTN-FEC, intended for advanced telecom and networking equipment. The device is housed in a 780-FCBGA package measuring 29 x 29 mm and supports serial networking interfaces including SFI and XFI. Its position in the networking hierarchy is Ethernet physical-layer and transport interface, where it links high-speed line-side equipment to optical or copper transport paths. A 10GE PHY is an Ethernet physical-layer transceiver that converts parallel digital data into high-speed serial signaling for network transmission and converts incoming serial signals back into digital data. The VSC8494YJE-12 combines dual/quad 10GbE capability with OTN-FEC functionality, making it suitable for equipment that requires Ethernet throughput and forward-error-correction capability in the same high-density package. The 780-FCBGA construction supports complex, high-pin-count telecom designs while requiring careful PCB layout and thermal management. The verified product information identifies the VSC8494YJE-12 as an Ethernet switch device and as a dual/quad 10GE PHY with OTN-FEC. These descriptions establish its principal use in carrier-grade Ethernet, optical transport, and other high-speed network-interface applications. It is also identified as a telecom interface IC with SFI and XFI serial interfaces, which are important to systems using serializer/deserializer links between line cards, optical modules, and network processors. Because this product is supplied in a 780-FCBGA package, its implementation is not limited by pin count in the same way as a small-outline package. The package can expose extensive high-speed differential I/O, supply rails, reference interfaces, control signals, and configuration pins. Board design should therefore treat power delivery, return paths, connector and transceiver placement, and thermal spreading as a single system-level problem. The exact pin assignments, voltage requirements, and recommended power architecture should be taken directly from the Microchip product documentation. Typical applications include 10GbE line cards, optical transport modules, Ethernet aggregation equipment, access and metro network systems, and telecom racks requiring dense high-speed connectivity. In these systems, the device can serve as the line-side Ethernet interface when optical transport requires OTN-FEC and serializer framing alongside 10GbE traffic. Design selection should account for the required number of channels, supported line rate, host interface, optical-module architecture, thermal budget, and board-level test access. Engineers should use the manufacturer datasheet for the complete 780-ball pin map, recommended power supplies, reference-clock requirements, high-speed differential pair assignments, and PCB stack-up guidance. The package is large and pin-dense, so connector launch geometry, return vias, impedance control, and thermal vias directly affect signal integrity. Avoid making substitute decisions from function descriptions alone; a valid replacement must match the 780-FCBGA footprint, ball assignments, electrical limits, interface configuration, and system-specific requirements. This product page combines distributor availability references, the manufacturer-direct product result, cross-reference information, and engineering guidance focused on package reuse, signal integrity, thermal design, and qualification. It is intended to help hardware engineers evaluate whether the VSC8494YJE-12 fits a dense 10GbE telecom design and where to obtain the definitive datasheet and current commercial response.

RFQ যোগাযোগ
VSC8494YJE-13 Dual/Quad 10GbE Universal PHY | Microchip
VSC8494YJE-13

VSC8494YJE-13 Dual/Quad 10GbE Universal PHY | Microchip

The Microchip Technology VSC8494YJE-13 is a dual/quad 10GbE universal PHY with OTN forward-error correction, packaged in a 780-FCBGA (29 mm × 29 mm) module. It serves as a high-speed Ethernet interface IC for telecommunications equipment, combining dual or quad 10GbE channel support with OTN-FEC functionality in one high-pin-count package. The product is intended for modern optical transport, Ethernet switching, aggregation, and line-card designs requiring deterministic high-speed serial connectivity. A universal PHY is a semiconductor that handles the physical-layer functions needed to transmit and receive high-speed data over a defined interface. In the networking hierarchy, this device belongs to Ethernet interface ICs, network interface controllers, physical-layer transceivers, and ultimately broader integrated-circuit and semiconductor categories. Unlike a complete network switch, a universal PHY focuses on the electrical interface between a communications processor or switching fabric and external network channels, including serialization, signal conditioning, clocking, and error-management functions. The defining feature of the VSC8494YJE-13 is its support for dual or quad 10GbE channels together with OTN forward-error correction. OTN-FEC can improve transport reliability by detecting and correcting errors in optical-network paths. Combining these capabilities can reduce the need for external correction resources while supporting dense line-card designs. The 780-FCBGA package provides extensive high-speed connectivity and power-distribution capability, but it also requires careful PCB layout and a very high pin count. As a telecommunications interface IC, the VSC8494YJE-13 is suited to infrastructure equipment where multiple 10GbE paths must coexist with high-speed optical transport. Its dual/quad configuration allows designers to scale channel density when a board must terminate several Ethernet links. OTN-FEC support is especially relevant where link budgets are constrained, long-distance transport is required, or maintaining service through transient optical-path errors is important. Typical uses include 10GbE optical line cards, packet-optical transport platforms, Ethernet aggregation equipment, access-network concentrators, and high-capacity switching systems. In these applications, the PHY provides the physical-layer foundation for a forwarding engine, switch ASIC, FPGA, or network processor. Exact host-interface mode, supported media types, lane rates, clocking architecture, and electrical characteristics should be confirmed against the current Microchip datasheet before schematic capture. Because this device uses a 780-FCBGA package, layout quality is fundamental to reliable 10GbE operation. High-speed differential nets require continuous reference planes, appropriate via transitions, controlled impedance, minimized stubs, and strict separation between aggressor signals. Power and ground distribution also require close attention because numerous high-speed links can create substantial simultaneous switching activity. Follow the manufacturer's recommended ball assignments, layer stack-up, decoupling, and test-access guidance. This product overview combines the identified channel and packaging characteristics with practical guidance for telecom line-card, optical transport, aggregation, and high-density Ethernet interface design. It also distinguishes verified catalog facts from detailed electrical parameters that require direct confirmation from the manufacturer datasheet, helping engineers evaluate PCB complexity and implementation risk before committing the VSC8494YJE-13 to a new design.

RFQ যোগাযোগ
VSC8496YMJ - 4x10GE OTN-FEC Transceiver | Microchip
VSC8496YMJ

VSC8496YMJ - 4x10GE OTN-FEC Transceiver | Microchip

The Microchip VSC8496YMJ is a four-port 10 Gigabit Ethernet transceiver IC with integrated OTN FEC, IEEE 1588v2 timing, and OAM support. It is associated with the Microsemi Corporation telecom interface product family and is supplied in tray packaging. The device provides serial, SFI, and XFI connectivity for demanding telecommunications infrastructure, including Carrier Ethernet switch, router, and DWDM systems. An Ethernet transceiver is a semiconductor that converts parallel or serial digital data into high-speed serial signals and performs the corresponding receive functions. Within a Carrier Ethernet equipment hierarchy, the VSC8496YMJ combines four 10GE channels, forward-error-correction capability, precision timing, and operations-administration-management functions. This integration supports equipment architects that need high-throughput interfaces without separating every PHY, FEC, timing, and OAM function into discrete components. The VSC8496YMJ's principal features include four 10 Gigabit Ethernet channels, integrated OTN FEC, IEEE 1588v2 timing implemented in the PHY, and OAM functionality. Its serial, SFI, and XFI interfaces provide options for connecting the transceiver within switching, routing, transport, and optical transport equipment. Integration of timing in the PHY is intended to provide accurate synchronization with low loss of precision in Carrier Ethernet and DWDM infrastructure. The device belongs to a specialized telecommunications silicon category rather than a conventional general-purpose Ethernet PHY. VeriTime distributed timing technology is integrated into the VSC8496 device, with the manufacturer describing it as a patent-pending implementation of IEEE 1588v2 timing. Such timing support is important in packet networks where clock synchronization, service delivery, and network observability must remain consistent across switching and transport domains. Typical applications include Carrier Ethernet switches and routers, DWDM transport systems, telecom aggregation equipment, timing-aware packet-network appliances, and high-capacity Ethernet line-card designs. The four-channel architecture is particularly relevant where multiple 10GE links terminate on one communications card. Product qualification should still be based on the complete carrier, optical module, clocking, thermal, and interoperability design rather than on transceiver capability alone. A primary design consideration is high-speed signal integrity. SFI and XFI routes require controlled impedance, low-loss PCB materials, suitable connector or optical-module interfaces, and carefully managed power and return paths. The integrated FEC and timing functions must also be validated with the surrounding line-card clock architecture, firmware, network-control software, and system-level timing budget. This product overview combines the manufacturer's interface description, exact ordering attributes, RoHS status, and published telecom functions with engineering-focused application guidance. It is intended to accelerate initial component screening while preserving the need to review the complete manufacturer datasheet, reference design, and application requirements before a production design is released.

RFQ যোগাযোগ
VSC8501XML - Single-Port Gigabit Ethernet PHY | Microchip
VSC8501XML

VSC8501XML - Single-Port Gigabit Ethernet PHY | Microchip

The Microchip Technology VSC8501XML is a single-port Ethernet physical-layer transceiver for 10/100/1000BASE-T networks, supplied in a 135-pin QFN package measuring 12 mm by 12 mm. It supports space-constrained Gigabit Ethernet equipment and incorporates line-side termination to conserve board area, reduce EMI, and improve system performance. The device also provides integrated RGMII timing compensation, allowing designers to reduce external timing-adjustment circuitry and simplify PCB implementation. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into electrical signaling for transmission over twisted-pair cable and converts received signaling back into digital data. In the broader component hierarchy, the VSC8501XML is an Ethernet interface IC, a networking semiconductor, and a physical-layer device within an Ethernet communications system. It connects a network processor, switching silicon, industrial controller, or embedded system to an RJ45-based copper network through suitable magnetic-interface components. The principal features confirmed for the VSC8501XML include support for 10/100/1000BASE-T operation, one Ethernet port, integrated line-side termination, integrated RGMII timing compensation, surface-mount construction, and a 135-QFN 12 mm by 12 mm package. The integrated termination is especially useful where PCB area is constrained because it removes the need for a discrete termination network on the line side. Lower board-area requirements can simplify placement around magnetics and connectors, although the Ethernet magnetics, connector, passive network, and controlled-impedance layout remain essential to signal integrity. VSC8501XML belongs to Microchip's VSC8501 family and is identified by the XML ordering suffix. The 135-pin package exposes the digital host interface, analog line-side connections, power supplies, control pins, reference components, and configuration or test functions required by the PHY. Because the device supports multiple Ethernet rates, designers can use one physical-layer solution for 10 Mb/s, 100 Mb/s, and 1 Gb/s copper links when the surrounding magnetics and network implementation support the required media. Exact voltage ratings, temperature limits, clock requirements, register behavior, and performance metrics must be confirmed in the manufacturer datasheet before schematic capture. Typical applications include industrial Ethernet gateways, programmable logic controllers, factory automation equipment, network interface cards, embedded Linux systems, IP cameras, access-control terminals, and compact communications appliances. The single-port architecture is particularly suitable for equipment with one copper Ethernet connection. In these systems, the VSC8501XML can sit between an Ethernet-capable processor and a network transformer, while software configuration controls speed negotiation, autonegotiation, and operating behavior. When laying out the board, preserve the differential geometry required by the Ethernet line-side pairs and keep high-speed traces short and continuously referenced to a solid ground plane. Follow the pin-description table, recommended external-network diagram, and decoupling guidance in the Microchip VSC8501 datasheet. Confirm the exposed-pad connection, power-plane arrangement, magnetic-component selection, and resistor-network values against the exact XML suffix before releasing production artwork. This product page consolidates the verified package and technology facts, drop-in-family cross-reference results, application guidance, and PCB considerations into a focused engineering reference. It also separates confirmed characteristics from parameters that require review of the official manufacturer documentation, helping designers evaluate the VSC8501XML before committing to a high-speed Ethernet design.

RFQ যোগাযোগ
VSC8502RD - 2-Port Gigabit Ethernet PHY | Microchip Technology
VSC8502RD

VSC8502RD - 2-Port Gigabit Ethernet PHY | Microchip Technology

The Microchip Technology VSC8502RD is a two-port Gigabit Ethernet copper PHY designed for space-constrained 10/100/1000BASE-T Ethernet designs. It combines integrated line-side termination with a reduced external-component approach intended to conserve board area, lower electromagnetic interference, and simplify system implementation. The verified manufacturer and distributor results identify the device as a two-port Gigabit Ethernet PHY with GMII/RGMII support, while the supplied package-specific MPN is VSC8502RD. A copper Ethernet PHY is the physical-layer interface between a digital Ethernet controller or processor and a twisted-pair network cable. It performs signal encoding, decoding, clock and data recovery, and electrical termination needed for reliable data transmission. The VSC8502 therefore belongs to the Ethernet interface controller and physical-layer device hierarchy, where it sits between a MAC or switching engine and the network magnetics or transformer-coupled cable interface. Its integrated line-side termination is particularly relevant to compact consumer, industrial, and embedded networking equipment. The supplied manufacturer information highlights integrated line-side termination as a board-space and EMI benefit. For 10/100/1000BASE-T applications, the two-port arrangement can reduce the number of separate PHY devices required by a dual-port network design. GMII and RGMII provide selectable digital interfaces for systems using either parallel or reduced-pin serial connections, allowing the PHY to fit different host architectures. The supplied data does not specify the exact package dimensions, pin count, electrical limits, operating-temperature range, or power consumption, so those values are not inferred here. Typical uses include compact Ethernet switches, industrial control equipment, embedded gateways, set-top equipment, and other designs requiring two copper-network ports. System designers should verify the exact VSC8502RD package, reference schematic, magnetic component, media interface, clocking, and host-side signal requirements against the Microchip documentation before layout release. The VSC8502RD-VR entry shown in the supplied distributor cross-reference data should likewise be checked against the target ordering code and mechanical drawing rather than assumed to be interchangeable. This product page consolidates the verified manufacturer description, distributor availability references, the VSC8502RD ordering entry, and the supplied VSC8502RD-VR cross-reference result. It also distinguishes confirmed application-level facts from electrical and mechanical details that require the manufacturer datasheet for final design decisions.

RFQ যোগাযোগ
VSC8502RD-VR - Gigabit Ethernet PHY | Microchip
VSC8502RD-VR

VSC8502RD-VR - Gigabit Ethernet PHY | Microchip

The Microchip Technology VSC8502RD-VR is a space-constrained Gigabit Ethernet physical-layer transceiver designed for 10/100/1000BASE-T applications. The device family supports integrated line-side termination to conserve board space, reduce electromagnetic interference, and improve system performance. The VSC8502RD-VR ordering code identifies a member of the VSC8502 Ethernet PHY family. A Gigabit Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between digital data supplied by a media-access controller and analog signals carried over twisted-pair cabling. The VSC8502 supports 10, 100, and 1000 Mb/s operation, allowing one physical-layer device to serve multiple Ethernet speed requirements. This PHY belongs to the interface-IC and network-interface hierarchy used in routers, switches, industrial controllers, and embedded equipment. Integrated line-side termination is a central feature of the VSC8502 family. Placing the termination network within the device can reduce the number of external passive components required around the magnetic interface. The manufacturer describes this integration as helping conserve board space, lower EMI, and improve system performance. Exact operating limits, electrical thresholds, temperature ratings, and pin assignments must be confirmed in the manufacturer documentation before schematic release. The VSC8502 family is intended for compact 10/100/1000BASE-T equipment where PCB area and external-component count are important. Its multi-rate capability makes it applicable to industrial Ethernet interfaces, communication equipment, embedded control systems, and managed network products. The integrated termination feature can also simplify board layout in applications requiring repeatable magnetics-interface implementation across multiple ports. Typical implementations place the PHY beside an Ethernet transformer and connect it to a network processor, switch fabric, or other digital controller through an appropriate digital interface. The physical implementation should preserve controlled differential routing, adequate return paths, and a properly designed termination network. Because exact pin names, supply voltage, clock requirements, and interface modes are not stated on the manufacturer product page excerpt, designers should use the complete VSC8502 datasheet and package drawing for implementation decisions. Design planning should begin with the required Ethernet speed, magnetics selection, digital-controller interface, board stack-up, and environmental target. Check the package pin count, exposed-pad requirements, decoupling recommendations, and layout guidance in the manufacturer documentation. This overview supports initial architecture selection, while the complete datasheet remains the controlling source for production release. This product page combines manufacturer application information with practical Ethernet-interface guidance, replacement considerations, and design notes. It is intended to accelerate component selection for 10/100/1000BASE-T designs while directing engineers to the authoritative datasheet for pin-level and production details.

RFQ যোগাযোগ
VSC8504XKS-01 - Quad-Port Gigabit Ethernet PHY | Microchip
VSC8504XKS-01

VSC8504XKS-01 - Quad-Port Gigabit Ethernet PHY | Microchip

The Microchip Technology VSC8504XKS-01 is a quad-port Gigabit Ethernet physical layer transceiver with EcoEthernet and Energy Efficient Ethernet support, packaged in a 256-ball PBGA measuring 17 x 17 mm. It consolidates four Gigabit Ethernet channels into one integrated circuit for equipment requiring multiple network connections without allocating a separate PHY device to every port. A Gigabit Ethernet physical layer, commonly called a Gigabit Ethernet PHY, converts high-speed serial signaling on copper cabling into data that a network controller or system-on-chip can process. Within the Ethernet hierarchy, the VSC8504 belongs to the physical-layer transceiver class and connects an Ethernet MAC through a standard digital interface. Energy Efficient Ethernet allows supported links to reduce power when traffic is light, while EcoEthernet provides additional power-management capabilities for network equipment. The VSC8504 family integrates four Gigabit Ethernet channels in one package. This high channel density reduces board-area requirements compared with four separate single-port devices, although the 256-ball package still demands careful escape routing, power planning, and thermal design. The source information identifies the PHY as supporting 10/100/1000BASE-T Ethernet operation, although exact trace-length, reach, and media specifications should be confirmed in the manufacturer documentation for the selected board design. The multi-port architecture is particularly useful in network switches, routers, industrial gateways, and data-center edge equipment where four copper Ethernet ports are required. A common implementation places the VSC8504 beside a switching or routing controller, connects each PHY to the corresponding MAC interface, and routes the four differential copper pairs through controlled-impedance PCB traces. Magnetic isolation and surge protection must be added when the device is connected to external cabling. VSC8504XKS-01 is suited to enterprise networking, data-center infrastructure, and consumer networking equipment identified by Microchip. Quad-port integration can simplify synchronization and board layout, but each channel still requires suitable magnetic components or an appropriate integrated isolation solution. Firmware configuration, register compatibility, and the precise supported operating modes should be reviewed against the current manufacturer product documentation before schematic release. PCB implementation requires strict attention to high-speed differential routing, continuous return paths, controlled impedance, and separation between PHY clocks, data interfaces, and analog copper-network connections. Follow the VSC8504 Hardware Design Checklist for layer construction, component placement, power, and copper media guidance. Decoupling, thermal relief around the PBGA, and the specified ball-to-land-pattern alignment are essential to first-pass manufacturability. This product record combines the manufacturer’s quad-port Gigabit Ethernet positioning with package data, verified source links, practical hardware guidance, lifecycle considerations, and a constrained comparison of same-package family options. The result helps engineers assess PCB reuse, interface compatibility, and thermal complexity before committing the VSC8504XKS-01 to an Ethernet networking design.

RFQ যোগাযোগ
VSC8504XKS-04 Quad-Port Gigabit Ethernet PHY | Microchip
VSC8504XKS-04

VSC8504XKS-04 Quad-Port Gigabit Ethernet PHY | Microchip

The Microchip Technology VSC8504XKS-04 is a four-port Gigabit Ethernet physical layer transceiver with support for 10/100/1000 Mb/s copper and fiber links, supplied in a 256-pin PBGA package measuring 17 x 17 mm. It provides (Q)SGMII connectivity and integrates Microchip EcoEthernet and IEEE 802.3az Energy Efficient Ethernet capabilities for power-conscious network equipment. The device operates from a 3.3 V supply in the identified configuration. A Gigabit Ethernet PHY is the physical-layer component that converts digital data into signals suitable for transmission over copper or optical media, while recovering incoming signals and supporting link negotiation. Within the network hierarchy, the PHY sits between a MAC or switching fabric and a network medium. The VSC8504 consolidates four Gigabit Ethernet channels into one device, reducing component count in multiport switches, routers, access equipment, and industrial Ethernet systems. Key features include four Gigabit Ethernet ports, copper and fiber support, and (Q)SGMII interfaces for connecting the PHY to a host or switching ASIC. IEEE 802.3az Energy Efficient Ethernet allows the system to reduce power consumption when link traffic is light, while EcoEthernet provides additional network power-management features. These functions are particularly valuable in enterprise networking and data-center equipment where many continuously connected ports can create a substantial aggregate power load. The -04 ordering suffix identifies the specific configuration of the VSC8504 family, while XKS denotes its 256-pin PBGA implementation. A 256-ball grid supports the substantial number of high-speed I/O and power connections required by four independent Gigabit channels. The package is designed for surface-mount assembly and, according to the product listing information, is supplied in a tray. Its 17 x 17 mm footprint demands careful BGA layout, thermal via, power-plane, and high-speed signal-routing practices. Typical uses include enterprise access switches, data-center aggregation equipment, consumer networking products, industrial Ethernet gateways, and copper-to-fiber network interfaces. Because the device can address both copper and fiber links, it can support equipment requiring flexible media handling while centralizing four physical channels around a common (Q)SGMII-based architecture. Exact fiber, copper, clocking, and transceiver requirements should be confirmed against the manufacturer data sheet for the exact ordering code. A critical design consideration is the separation of analog and digital power delivery. The VSC8504 Hardware Design Checklist recommends low-resistance local supply paths, correctly positioned decoupling, and ferrite beads ahead of series inductors where filtering is needed. Controlled impedance routing, short high-speed connections, uninterrupted reference planes, and careful BGA escape routing are equally important for reliable (Q)SGMII and Ethernet performance. This product record combines the manufacturer’s device positioning with exact package, interface, speed, compliance, and sourcing details, then adds implementation guidance, replacement analysis, and application-oriented design considerations. It is intended to help engineers qualify the PHY for a multiport Ethernet design before committing to a complex 256-pin BGA layout.

RFQ যোগাযোগ