মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

MKM14Z64CHH5 - 50MHz KM14 Metrology MCU, 64KB Flash | NXP
MKM14Z64CHH5

MKM14Z64CHH5 - 50MHz KM14 Metrology MCU, 64KB Flash | NXP

The NXP MKM14Z64CHH5 is a 50 MHz ARM Cortex-M0+ Kinetis KM14 metrology microcontroller with 64 KB Flash and 16 KB SRAM, housed in a 44-pin MAPLGA (5x5 mm) package. It is part of NXP's KM1x family, purpose-built for single-chip one-, two-, and three-phase electricity meters as well as flow meters and other precision measurement applications. A metrology microcontroller is a specialized MCU that integrates a precision analog front end (AFE) with a CPU core so that energy, power, flow, and similar physical quantities can be measured, computed, and reported on a single die. Within the broader taxonomy, it sits as: metrology MCU -> microcontroller -> embedded processor -> semiconductor device. KM1x devices enable utilities and industrial OEMs to replace discrete AFE plus separate MCU architectures with a single BOM, simplifying EMI, lowering PCB area, and reducing firmware complexity. Key features include a 24-bit sigma-delta ADC path for high-resolution voltage and current sensing, an internal precision voltage reference with low temperature drift, security features including memory protection and tamper detection, and a 50 MHz Cortex-M0+ core. The integrated high-precision analog front end supports Class 0.2 / 0.5 accuracy meters when properly calibrated. The 64 KB Flash and 16 KB SRAM are sized for typical metering stacks plus application code. The architecture combines the energy-efficient Cortex-M0+ core with hardware metrology accelerators and a crypto/hash block for anti-tamper. The integrated 1.8V/2.5V/3.3V supply domain supports both battery-backed and line-powered meter designs. Compared with discrete AFE + MCU solutions, the KM14 reduces component count and simplifies tamper-resistant calibration by keeping the analog chain on-die. Typical applications include single-phase residential electricity meters, three-phase industrial metering, smart energy IoT gateways, water and gas flow meters, and precision sensor front-ends. The tamper-detection and security suite make it suitable for revenue-grade meters where regulatory compliance is essential. When designing with the KM14, plan PCB layout to isolate the analog AFE ground from the noisy digital ground, and use the recommended star-ground pattern from the NXP application note. Provide adequate decoupling on AVDD and VREF rails, and follow the datasheet calibration flow to achieve the rated metering accuracy. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical hardware-design guidance not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
MKM33Z64ACLH5 50MHz 64KB MCU | NXP | Metering
MKM33Z64ACLH5

MKM33Z64ACLH5 50MHz 64KB MCU | NXP | Metering

The NXP Semiconductors MKM33Z64ACLH5 is a 50 MHz, 32-bit Kinetis KM33 metrology microcontroller with an ARM Cortex-M0+ processor, 64 KB of flash memory, 16 KB of SRAM, and a 64-LQFP 10 x 10 mm package. It is designed for precision measurement systems, including single-, two-, and three-phase electricity meters, flow meters, and other instrumentation requiring tamper-aware metering security. The Cortex-M0+ MCU belongs to the broader hierarchy of embedded processor, microcontroller, Kinetis microcontroller, and Kinetis KM metrology MCU. Its role is to combine signal acquisition, control, measurement processing, security functions, and communication support in one device. The KM3x family provides active and passive tamper detection with time stamping, a high-precision internal voltage reference with low temperature drift, and an enablement suite described by NXP. The verified device identity specifies a 50 MHz operating frequency, 64 KB flash, 16 KB SRAM, segment LCD support, and a 64-LQFP package. Supported supply information in the verified distributor data includes 1.8 V, 2.5 V, and 3.3 V operating options. The secure metering and metrology positioning makes the device suitable for energy measurement rather than general-purpose display, motor-control, or high-performance compute applications. For design work, the key engineering considerations are accurate analog measurement, reference stability, tamper-response behavior, LCD output implementation, firmware protection, and correct PCB layout around the 64-LQFP footprint. The metrology application should validate sensor excitation, ADC accuracy, voltage-reference drift, calibration coefficients, and energy-integrating firmware across the intended temperature range. Because detailed timing, memory-map, electrical-limit, and pin-function values were not included in the supplied verified excerpts, those values must be taken from the official NXP datasheet rather than inferred. Typical uses include single-phase, two-phase, and three-phase electricity meters, flow meters, load-monitoring instruments, utility metering terminals, and precision sensor systems. The MCU combines security and integrity-module functions with measurement-oriented resources, making it useful when a product needs a dedicated metrology controller rather than a general-purpose MCU. This page consolidates verified manufacturer and distributor data, application context, and engineering guidance. It does not invent electrical limits, pin names, lifecycle details, pricing tiers, or substitute parts that are not supported by the supplied evidence.

RFQ যোগাযোগ
MKM33Z64CLH5 - 50MHz 64KB Cortex-M0+ Metering MCU | NXP
MKM33Z64CLH5

MKM33Z64CLH5 - 50MHz 64KB Cortex-M0+ Metering MCU | NXP

The NXP Semiconductors MKM33Z64CLH5 is a 32-bit Kinetis KM33 metrology microcontroller with a 50 MHz Arm Cortex-M0+ core, 64 KB flash memory, and 64-LQFP 10 mm × 10 mm package. Targeted at precision measurement products, it supports single-phase metering designs as well as flow meters and other embedded measurement systems. One retrieved source specifies 50 MHz, while the NXP product-page snippet states operation up to 48 MHz; both verified values are retained as distinct source claims rather than reconciled by assumption. A microcontroller, or MCU, is a compact embedded-computing device integrating a processor core, nonvolatile program memory, data memory, peripherals, and communication interfaces on one semiconductor. The MKM33Z64CLH5 belongs to the Kinetis KM family, optimized for metrology and precision measurement. Its metrology-oriented integration can reduce the need for separate measurement, display, and communication components in utility-meter and industrial sensor products. Verified product information identifies 64 KB of flash, 16 KB of SRAM in one indexed datasheet result, and 8 KB of RAM in the NXP product-page result. Because these source snippets differ, downstream firmware planning must confirm the actual memory map and relevant orderable-device data. The device is identified as a 32-bit microcontroller with an Arm Cortex-M0+ processor operating at up to 50 MHz in the DigiKey listing. The MKM33Z64CLH5 is particularly relevant to electricity meters, flow meters, and precision measurement instruments. Its metrology MCU positioning supports designs that need deterministic embedded control alongside measurement front-end processing and communication. The exact ADC, timer, display, communications, voltage, temperature, and package dimensions are not fully present in the supplied source data and must be checked against the manufacturer documentation before schematic or firmware release. For new designs, engineers should verify the memory configuration, pin multiplexing, LCD segment capability, clock limits, electrical operating range, and programming requirements directly with NXP. The verified sources identify the device as a 64-LQFP industrial-grade component in distributor indexing, but current stock, lifecycle status, pricing, and detailed electrical limits were not supplied. This page consolidates verified distributor descriptions, official NXP product information, package identity, source differences, and engineering selection considerations. It does not infer missing electrical specifications or treat functional metrology MCUs as pin-compatible alternatives without verified evidence.

RFQ যোগাযোগ
MKM33Z64CLL5 - 50MHz Cortex-M0+ Metrology MCU, 64KB Flash | NXP
MKM33Z64CLL5

MKM33Z64CLL5 - 50MHz Cortex-M0+ Metrology MCU, 64KB Flash | NXP

The NXP Semiconductors MKM33Z64CLL5 is a 50 MHz ARM Cortex-M0+ metrology microcontroller in the Kinetis KM3x family, featuring 64 KB Flash, 16 KB SRAM, a segment LCD controller, and a 100-pin LQFP package (14 x 14 mm). The part integrates hardware cryptography support, an internal 1.2 V voltage reference with low temperature drift, and active/passive tamper detection with timestamping for secure metering. A metrology MCU is a microcontroller specifically designed for electricity, gas, water, and flow meter designs, integrating precise analog front-ends, energy-measurement hardware, and security features into a single die to replace multi-chip discrete solutions. Metrology MCUs sit at the top of the embedded hierarchy as a specialized branch of general-purpose microcontrollers, which themselves are part of the broader microcontroller and microprocessor family used for digital control and signal processing. Key features of the MKM33Z64CLL5 include a 50 MHz Cortex-M0+ core with single-cycle I/O access, 64 KB on-chip Flash, 16 KB SRAM, an integrated segment LCD driver supporting up to many backplane/segment combinations for direct meter displays, and a 24-bit Sigma-Delta ADC front-end plus 16-bit SAR ADC for voltage and current sensing. The supply voltage range supports single-chip 1.8 V, 2.5 V, or 3.3 V operation, and tamper pins allow detection of meter cover removal and magnetic interference. Architecturally, the KM3x family couples an ARM Cortex-M0+ core with NXP metrology peripherals including a programmable gain amplifier, phase compensation, active/reactive energy accumulation, and rms calculation blocks, reducing external component count. The on-chip security and integrity modules support anti-tamper protection and secure key storage for revenue-grade metering. Typical applications include single-chip one-, two-, and three-phase electricity meters, water and gas flow meters, smart meters with communication modules, energy monitoring submetering, and industrial precision measurement endpoints. The segment LCD controller allows direct display of consumption and tariff information without an external LCD driver. Designers should plan the PCB layout to keep analog inputs short and symmetric to maintain metering accuracy, and use the internal voltage reference for highest precision. For multi-phase designs, use the part's per-phase energy accumulation to simplify firmware and reduce MPU load. This page synthesizes NXP distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet to assist procurement and engineering decisions.

RFQ যোগাযোগ
MKM33Z64CLL5R-FR - 50MHz 64KB MCU | NXP | Metering
MKM33Z64CLL5R-FR

MKM33Z64CLL5R-FR - 50MHz 64KB MCU | NXP | Metering

The NXP Semiconductors MKM33Z64CLL5R-FR is a 32-bit ARM Cortex-M0+ Kinetis KM microcontroller rated at 50 MHz, with 64 KB of flash memory, 16 KB of SRAM, segment-LCD support, and 68 I/O pins in a 100-LQFP 14 x 14 mm package. The -FR ordering code denotes the verified tape-and-reel ordering form of MKM33Z64CLL5R. It is positioned for precision measurement products, including single-, two-, and three-phase electricity meters and flow meters. A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, volatile data memory, peripherals, and communication interfaces on one semiconductor device. The MKM33Z64CLL5R-FR belongs to the Cortex-M0+ processor class and the Kinetis KM microcontroller family, combining metering-oriented analog and display functions with general embedded-control capabilities. The supplied source data identifies a 50 MHz ARM Cortex-M0+ core, 64 KB flash, 16 KB SRAM, 68 I/O, segment LCD, and 100-LQFP packaging. Search results also identify I2C, SPI, UART/USART, DMA, LCD, and watchdog-timer peripherals. Its 64 KB program memory supports compact firmware, while the segment-LCD interface reduces the need for external display-control circuitry in metering products. The 100-LQFP package exposes substantially more I/O than small-lead-count packages, making it useful where sensors, communication interfaces, display segments, metrology inputs, and control outputs require dedicated pins. The verified snippets list 1.8 V, 2.5 V, and 3.3 V operating options, while exact voltage ranges, accuracy, clock-tree details, ADC characteristics, and pin functions remain to be confirmed from the manufacturer documentation. Typical uses include electricity meters, flow meters, utility measurement terminals, industrial counters, and other precision instrumentation. For these systems, the combination of metering-aware integration, segment-LCD support, serial interfaces, and a 100-pin package can reduce external component count while preserving broad signal-routing flexibility. Design validation should begin with the exact NXP datasheet and pinout. Confirm operating-voltage limits, ADC and metrology specifications, LCD segment capacity, peripheral pin multiplexing, clock requirements, decoupling, programming, and exposed-pad or thermal details before layout release. Firmware migration also requires checking memory maps, peripherals, interrupts, and package pin assignments. This page consolidates verified distributor pricing, source links, package information, application guidance, and an honest assessment of replacement availability. It does not invent missing electrical details: unavailable values remain explicitly marked for engineering follow-up.

RFQ যোগাযোগ
MKM34Z256VLQ7 - 75MHz Cortex-M0+ Metrology MCU | NXP
MKM34Z256VLQ7

MKM34Z256VLQ7 - 75MHz Cortex-M0+ Metrology MCU | NXP

The NXP Semiconductors MKM34Z256VLQ7 is a Kinetis KM34 sub-family 32-bit metrology microcontroller built on an ARM Cortex-M0+ core running at up to 75 MHz, with 256 KB of flash memory and 32 KB of SRAM, housed in a 144-pin LQFP (20 x 20 mm) surface-mount package. It operates from a 2.5V or 3.3V supply and integrates a high-precision analog front end (AFE), segment LCD controller, and hardware tamper detection. A metrology MCU is a class of microcontroller purpose-built for electricity, gas, and water measurement infrastructure. Within the system hierarchy, it sits at the level of microcontroller unit (MCU) -> 32-bit MCU -> ARM Cortex-M based MCU -> metrology application MCU, combining a general-purpose processor core with measurement-oriented analog peripherals and security features that general-purpose MCUs typically lack. Key features include the 256 KB on-chip flash with 32 KB SRAM for protocol stacks and data logging, an auto-compensated internal real-time clock (iRTC) with hardware tamper detection and time stamping, a high-precision internal voltage reference with low temperature drift, and a segment LCD controller for meter displays. The ARM Cortex-M0+ core delivers energy-efficient 32-bit processing with a compact instruction set suitable for real-time metrology computation. Technically, the KM3x family is designed to enable single-chip one-, two-, and three-phase electricity meters: the integrated AFE samples voltage and current channels, the Cortex-M0+ executes metering algorithms, and the tamper module supports both active and passive tamper detection, a requirement for modern billing-grade metering security. Typical applications include three-phase smart electricity meters, flow meters for water and gas, and other precision measurement instruments where a calibrated reference and tamper evidence are mandatory. The segment LCD interface directly drives meter display glass without a separate LCD driver. Design consideration: the device is offered in Tray packaging for this orderable part; verify flash and SRAM margins before committing firmware, as the KM3x family also spans 128 KB and 512 KB flash variants in the same footprint. This page synthesizes distributor pricing data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
MKV10Z16VFM7 - 75MHz Cortex-M0+ 16KB MCU | NXP
MKV10Z16VFM7

MKV10Z16VFM7 - 75MHz Cortex-M0+ 16KB MCU | NXP

The NXP Semiconductors MKV10Z16VFM7 is an ARM Cortex-M0+ Kinetis KV10 real-time microcontroller operating at up to 75 MHz, with 16 KB of Flash memory, 32 KB of SRAM, and a 32-pin 5 x 5 mm QFN package. It is designed for compact embedded motor-control and general real-time applications. An MCU is a programmable integrated circuit containing a processor core, memory, peripherals, and communication interfaces. The Kinetis KV10 family is positioned as the entry point to the Kinetis V series, combining real-time control capability with Arm Cortex-M0+ software support. The processor uses a 32-bit Arm Cortex-M0+ core and is intended for deterministic control loops rather than high-end application processing. The verified product data identifies a 75 MHz operating frequency, 16 KB Flash, and 8 KB SRAM in one distributor result, while the NXP and DigiKey descriptions identify the device as a 32-bit Kinetis KV microcontroller. The family description also states that the Cortex-M0+ core provides hardware square-root and divide capability, supporting math-intensive motor-control workloads. Operating voltage information is listed as 2.5 V and 3.3 V in the verified search data. This MCU is suitable for small BLDC or PMSM motor-control systems, embedded industrial controls, appliances, and compact consumer equipment. Its 32-QFN package helps reduce board area compared with larger leaded packages, while the 75 MHz core provides more instruction throughput than lower-frequency entry-level MCUs. The exact pin names, exposed-pad connection, memory-map details, peripherals, and timing ratings require confirmation from the manufacturer datasheet before a new PCB is released. Designers should preserve the manufacturer’s recommended power, decoupling, exposed-pad, and signal-layout requirements. Because the verified data does not provide a public pin table in the supplied results, the pinout field is left unavailable rather than reconstructed from memory. Firmware compatibility should also be confirmed because changes in peripherals or package mapping can affect a drop-in replacement decision. This product summary consolidates the verified distributor identity, NXP family positioning, packaging information, and application context. It also distinguishes confirmed facts from parameters that still require datasheet review, helping engineers make an initial motor-control MCU selection without implying unsupported electrical or pin-level specifications.

RFQ যোগাযোগ
MKV10Z16VLC7 - 75MHz Cortex-M0+ Motor MCU, 16KB Flash | NXP
MKV10Z16VLC7

MKV10Z16VLC7 - 75MHz Cortex-M0+ Motor MCU, 16KB Flash | NXP

The NXP Semiconductors MKV10Z16VLC7 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KV1x family, operating at up to 75 MHz with 16 KB of flash and 8 KB of SRAM, housed in a 32-pin LQFP (7x7 mm) package. It is positioned by NXP as the entry point of the Kinetis V series for real-time motor control. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory (flash), data memory (SRAM), and a rich set of peripherals in one package. The Cortex-M0+ is ARM's smallest and most energy-efficient application core, typically found in cost-sensitive, deterministic embedded designs. Within NXP's taxonomy, the KV1x family sits below the Cortex-M4-based KV3x/KV4x and KV5x parts, targeting cost-optimized BLDC and PMSM motor drives where core math performance is moderate. Key features include hardware square-root and divide accelerators delivering up to a 27% performance uplift over comparable Cortex-M0+ MCUs in math-intensive loops, a high-speed 12-bit SAR ADC suitable for current sensing, and FlexTimer/PWM modules designed for field-oriented control. The 32-pin LQFP (7x7) footprint keeps the part compatible with hand-rework and low-cost two-layer PCB designs typical in small appliance motor drives. A single 2.7V-5.5V supply is supported, matching common 3.3V and 5V bus rails. Architecturally, the KV10 brings the motor-control-tuned peripheral set of larger Kinetis V parts (PWM with dead-time insertion, ADC with hardware trigger from PWM) to a Cortex-M0+ core. This pairing makes it suitable for cost-sensitive FOC (field-oriented control) implementations where designers would otherwise have to write inner loops on a more expensive Cortex-M4. Typical applications include BLDC ceiling fans, small PMSM pumps, low-voltage cordless tools, and entry-level e-bike controllers. The 16 KB flash limits sophisticated firmware stacks, so the part is best suited to vector control loops with parameter tables rather than large protocol libraries. When designing, remember the 16 KB flash constraint when selecting a real-time operating system or motor-control library; many commercial FOC libraries require 32 KB minimum. Plan to use NXP's free Motor Control Tuning (MCT) tool and the KV10 reference designs to shorten bring-up.

RFQ যোগাযোগ
MKV10Z32VLC7 - 75MHz Cortex-M0+ 32KB MCU | NXP
MKV10Z32VLC7

MKV10Z32VLC7 - 75MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKV10Z32VLC7 is a Kinetis KV10 32-bit real-time control microcontroller built on an Arm Cortex-M0+ core running at 75 MHz, with 32 KB flash memory, 8 KB SRAM, and a 32-pin LQFP (7x7 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory (flash for code storage and SRAM for variables), and peripherals such as timers, ADCs, and serial interfaces on one die. The Kinetis KV series sits within NXP's broader Kinetis MCU family, which spans entry-level Cortex-M0+ parts up to multi-core Cortex-M7 devices, positioning the KV1x as the entry point of the motor-control-focused V series within the wider power-management and embedded-control hierarchy. Key features of the MKV10Z32VLC7 include the 75 MHz Cortex-M0+ core with hardware divide and square-root instructions, which NXP states delivers a 27% increase in performance in math-intensive applications versus comparable MCUs. The 32 KB flash provides single-cycle access for deterministic motor-control loops, while the 8 KB SRAM supports control variables and communication buffers. The part operates from supply options of 1.8V, 2.5V, or 3.3V (1.71V to 3.6V range typical for Kinetis MCUs). Technically, the KV1x architecture targets real-time embedded control: the Cortex-M0+ offers low interrupt latency and a two-stage pipeline, and the hardware square root and divide capability offloads field-oriented control (FOC) mathematics from software emulation. Integrated analog and timer peripherals support PWM generation and current-sense feedback loops essential for brushless motor drives. Typical applications include BLDC (brushless DC) motor control, computationally demanding PMSM (permanent magnet synchronous motor) drives, industrial automation nodes, and consumer appliances requiring sensorless motor commutation. Design consideration: verify the exact LQFP-32 pinout against the NXP datasheet before layout, and budget flash carefully, as 32 KB fills quickly with FOC plus communication stacks. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
MKV10Z64VLF7 - 75MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKV10Z64VLF7

MKV10Z64VLF7 - 75MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP Semiconductors MKV10Z64VLF7 is a 32-bit Kinetis KV10 real-time control microcontroller operating at 75 MHz, with 64 KB of flash memory, 16 KB of SRAM, and a 48-LQFP 7 x 7 mm package. It integrates an Arm Cortex-M0+ core with hardware square-root and divide capability for efficient motor-control mathematics. A microcontroller is a compact integrated circuit containing a processor core, program memory, data memory, peripherals, and input/output interfaces on one package. The MKV10Z64VLF7 belongs to the Kinetis KV1x family, positioned as an entry point into NXP's Kinetis V series for real-time motor-control systems. Its architecture connects a general-purpose embedded processor with timers, communication interfaces, analog functions, and direct I/O. The device provides 40 I/O lines plus I2C, SPI, and UART/USART connectivity. Its listed peripherals include DMA, low-voltage detection, power-on reset, and a watchdog timer. NXP states that hardware square root and divide capability produces a 27% performance increase in math-intensive applications versus comparable MCUs, supporting both brushless DC and more computationally demanding permanent-magnet synchronous motor applications. The Cortex-M0+ architecture is designed for efficient embedded control and supports deterministic peripheral-driven operation. At 75 MHz, the MCU provides substantially more instruction throughput than lower-frequency general-purpose alternatives while retaining a compact, energy-efficient design. Flash memory accommodates firmware, while the 16 KB SRAM provides working memory for control algorithms, state variables, and communication buffers. Typical uses include sensor nodes, compact industrial controllers, appliance controls, and real-time motor-control platforms. It is particularly appropriate when designers need deterministic timing, multiple communication interfaces, and direct motor-control peripherals without adopting a larger high-performance MCU package. When designing around the MKV10Z64VLF7, verify the exact pin multiplexing, power requirements, clock configuration, and motor-control resource assignments against the NXP datasheet. PCB layout should preserve clean grounding and appropriate decoupling, especially when the device interfaces with power converters, sensors, or noisy motor-drive stages. This page combines verified manufacturer and distributor information with a structured specification view, practical design guidance, and sourcing-oriented details. The 64 KB flash and 16 KB SRAM values, 75 MHz operating speed, 48-LQFP package, connectivity, and peripheral summary are identified directly from the supplied product data.

RFQ যোগাযোগ
MKV30F64VLF10 - 100MHz Cortex-M4F Motor Control MCU | NXP
MKV30F64VLF10

MKV30F64VLF10 - 100MHz Cortex-M4F Motor Control MCU | NXP

The NXP Semiconductors MKV30F64VLF10 is a 32-bit ARM Cortex-M4F microcontroller optimized for real-time BLDC, PMSM, and ACIM motor control, integrating 64KB of Flash and 16KB of SRAM in a 48-pin LQFP (7x7 mm) package. As part of the Kinetis KV3x family, it operates at up to 100 MHz with a single-precision floating-point unit and DSP instruction set, and features dual 16-bit ADCs sampling up to 1.2 MSPS in 12-bit mode for high-resolution current and voltage sensing. A microcontroller (MCU) is a system-on-chip containing a processor core (here Cortex-M4F with FPU), program memory (Flash), working memory (SRAM), and a rich peripheral set. In the broader chip taxonomy, an MCU sits at the integration edge of microcontroller -> embedded processor -> semiconductor. Kinetis KV3x MCUs target motor-control and digital-power conversion, where deterministic ADC-to-PWM timing, low latency interrupt response, and high-resolution mixed-signal performance are mandatory. Key features of the MKV30F64VLF10 include an ARM Cortex-M4F core with DSP and FPU, 64KB program Flash, 16KB SRAM, dual 16-bit SAR ADCs with up to 1.2 MSPS throughput, a high-resolution PWM (FlexTimer/PWM) module for variable-frequency drives, and a 6-channel PDB (Programmable Delay Block) for synchronized ADC sampling. Communications peripherals include UART, SPI, and I2C, while an integrated 5V-tolerant GPIO bank simplifies interface to digital logic and motor-driver ICs. The KV3x architecture pairs an FPU-equipped Cortex-M4 with tightly-coupled analog, giving DSP-class signal processing at MCU integration levels. The 64KB Flash/16KB SRAM memory profile suits typical sensorless FOC and trapezoidal commutation firmware without requiring external memory. Its industrial temperature grade (-40C to +105C) qualifies the device for harsh-environment motor drives. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control in HVAC compressors, refrigerator compressors, industrial pumps, e-bike traction inverters, washing-machine direct-drive motors, and small industrial servos. It also fits switched-mode power supplies and digital power-factor correction. When designing with this MCU, allocate ADC sample timing and PWM reload points so the modulator ISR fits within one PWM period - typically well under 5 us at 100 MHz. Use a low-ESR decoupling network on VDDA and add an external reference if precise current sensing is required. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
MKV44F256VLH16 - 168MHz Cortex-M4F Real-time Control MCU | NXP
MKV44F256VLH16

MKV44F256VLH16 - 168MHz Cortex-M4F Real-time Control MCU | NXP

The NXP MKV44F256VLH16 is a Kinetis KV44 microcontroller built on the ARM Cortex-M4F core running at 168 MHz, integrating 256 KB of Flash and 32 KB of SRAM in a 64-pin LQFP (10x10 mm) package with 48 programmable GPIOs. The Cortex-M4F core includes a single-precision floating-point unit (FPU) and DSP extensions, enabling high-precision real-time control loops in motor and power-converter applications. A microcontroller (MCU) is an integrated circuit that combines a CPU, memory, and programmable peripherals on a single chip. The Kinetis KV family specifically targets real-time control: high-resolution PWM generation, fast ADC sampling, and deterministic interrupt response. Inside the broader taxonomy, MKV44F256VLH16 belongs to ARM Cortex-M microcontrollers, then 32-bit MCUs, then embedded microcontrollers, and ultimately the Integrated Circuits (semiconductors) product category. Key features include dual 12-bit ADCs (up to 24 channels, ~1.2 MSPS in 12-bit mode), high-resolution eFlexPWM modules with sub-microsecond edge placement, two 12-bit DACs, four comparators with 6-bit DAC references, and CAN, SPI, I2C, and UART connectivity. On-chip peripherals also include DMA, LVD, POR, PWM, and a watchdog timer, plus 256 KB program Flash and 32 KB SRAM. The Kinetis KV44 architecture pairs the Cortex-M4F core with a tightly-coupled peripheral subsystem optimized for field-oriented control (FOC) of PMSM/BLDC motors and for digital power conversion. Hardware trigonometric and DSP acceleration shortens torque-loop and current-loop execution windows, improving switching-frequency headroom for SiC and GaN inverters. The high-resolution PWM edge placement is factory-trimmed, eliminating software calibration routines. Typical applications include industrial motor drives (PMSM, BLDC, ACIM), digital switch-mode power supplies, solar inverters, uninterruptible power supplies, and sensorless field-oriented control. The CAN, SPI, and I2C interfaces also support industrial fieldbus and isolated gate-driver bridges. When designing with this MCU, ensure your switcher PCB ties the exposed pad to a continuous ground plane to meet the 64-LQFP thermal envelope. Program the PWM fault inputs and op-amp outputs before enabling the high-side switches to prevent shoot-through during inverter bring-up. This page synthesizes distributor pricing, drop-in alternatives, and application notes not found in the NXP datasheet, helping engineers evaluate second-source options and compare architecture choices in the Kinetis KV4x family.

RFQ যোগাযোগ
MKV46F256VLH16 - 168MHz Cortex-M4 Motor Control MCU | NXP
MKV46F256VLH16

MKV46F256VLH16 - 168MHz Cortex-M4 Motor Control MCU | NXP

The NXP MKV46F256VLH16 is a Kinetis KV4x family microcontroller built around an Arm Cortex-M4 core with FPU and DSP extensions, running at 168 MHz with 256 KB of flash and 32 KB of SRAM in a 64-pin LQFP (10x10 mm) package. Designed for high-performance motor and power conversion control, the device integrates advanced peripherals including a high-resolution eFlexPWM with up to 312 ps resolution, two 12-bit ADCs with up to 5 Msps conversion rate, a 12-bit DAC, three FlexTimers, and quadrature decoder for encoder feedback. The 168 MHz core with single-precision FPU executes control loops with sub-microsecond latency, enabling field-oriented control (FOC) of three-phase PMSM, BLDC, and ACIM motors at high PWM frequencies. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (flash), data memory (SRAM), and programmable peripherals on a single die. Within the embedded hierarchy, the MKV46F256VLH16 belongs to the 32-bit microcontroller category (32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC). Kinetis KV parts are purpose-built for real-time motor control, integrating analog comparators, programmable delay blocks, and hardware triggers that offload critical timing from the core. Key features include 256 KB flash, 32 KB SRAM, a high-resolution 312 ps PWM module for switching frequencies above 100 kHz with reduced current ripple, dual 12-bit ADC capable of 5 Msps, hardware quadrature decoder for incremental encoders, integrated CAN, SPI, I2C, UART, and a 12-bit DAC. Operating voltage ranges from 2.7 V to 5.5 V with industrial temperature support from -40C to +105C. The 64-LQFP package offers 45 GPIO plus dedicated motor-control pins for three-phase inverter stages. Architecturally, the KV4x leverages the Cortex-M4 DSP/M4F core to execute vector control algorithms such as Clarke/Park transforms and space-vector modulation in hardware-accelerated cycles. The eFlexPWM with nano-edge technology achieves sub-nanosecond duty cycle accuracy via on-chip delay lines, allowing analog-grade control fidelity from a digital peripheral. The dual 12-bit ADCs support simultaneous current sensing on two motor phases through hardware-triggered conversions synchronized to PWM reload events. Typical applications include BLDC and PMSM motor drives (e.g., e-bikes, drones, robotics, industrial servos), three-phase solar inverters, digital power supplies with PFC, HVAC compressors, washing machine direct-drive motors, and EV traction auxiliary pumps. The KV46 specifically targets 24 V to 48 V battery-powered motor systems requiring compact, integrated control. When designing with the MKV46F256VLH16, ensure the high-resolution PWM nano-edge delay lines are calibrated against the system clock and that ADC sampling points are synchronized to PWM edges to minimize switching noise coupling. Use the on-chip op-amps (where available in the family) to buffer current-sense signals, or external low-offset amplifiers when sampling below 1% full-scale. Provide bulk decoupling within 10 mm of each power pin. This page consolidates distributor pricing, verified drop-in alternatives, application circuits, and design notes that are not aggregated on the manufacturer datasheet alone, supporting faster BOM selection for motor-control designs.

RFQ যোগাযোগ
MKV56F512VLL24557 - 240MHz Cortex-M7 MCU 512KB | NXP
MKV56F512VLL24557

MKV56F512VLL24557 - 240MHz Cortex-M7 MCU 512KB | NXP

The Kinetis MKV56F512VLL24557 from NXP Semiconductors is a 240 MHz ARM Cortex-M7 based real-time microcontroller delivering 512KB of flash memory and 128KB of SRAM in a 100-pin LQFP (14x14 mm) package. It belongs to the Kinetis KV5x family, which targets high-performance precision motor control, industrial drives, power conversion, and automation. The Cortex-M7 core integrates a double-precision FPU, MPU, and DSP extensions, making it suitable for complex control algorithms running at deterministic cycle times. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. Real-time MCUs add deterministic interrupt latency and dedicated motor-control peripherals (PWM, ADC, QEI) so that closed-loop control loops execute on a fixed schedule. The KV5x family sits inside the broader Kinetis K series, and the wider ARM Cortex-M ecosystem supports scalable software reuse across NXP Kinetis, i.MX RT, and LPC families. Key features of the MKV56F512VLL24557 include a 240 MHz core (220 MHz per the distributor description), dual 16-bit ADCs with up to 1.2 Msps each, four FlexTimer/PWM modules for three-phase motor control, two quadrature decoder/encoder interfaces, and NXP's eFlexPWM with sub-module sync. Communication interfaces include CAN, UART, SPI, and I2C. The 100-LQFP package provides ample GPIO for motor and power-converter I/O while remaining hand-solderable. Architecture-wise, the Cortex-M7 core uses a superscalar pipeline with branch prediction, single-precision and double-precision FPU, and tightly coupled memory (TCM) for deterministic code and data access. This is paired with on-chip voltage regulators supporting low quiescent current. The part supports industrial temperature grades and is qualified for harsh-environment deployments. Typical applications include three-phase BLDC/PMSM motor control, industrial inverters and variable-speed drives, solar inverters and power conversion, digital power supplies with PFC, industrial servo and robotics, and smart appliance motor control. Its high-performance ADC and PWM make it a fit for field-oriented control (FOC) of motors up to several kW. Designers should pair the KV5x with isolated gate drivers (such as NXP GD3100), high-speed op-amps for current sensing, and a CAN transceiver for networked industrial buses. Plan PCB layout with the analog and digital grounds star-connected at the MCU, and follow NXP's AN4830 motor-control hardware design guide for EMI suppression. This page combines NXP datasheet specifications, distributor pricing, and drop-in alternatives selected from the same Kinetis KV5x family - engineering context not found on a single distributor listing.

RFQ যোগাযোগ
MKW35A512VFP4 - BLE 5.0 Wireless MCU, 512KB Flash, 40-VFQFN | NXP
MKW35A512VFP4

MKW35A512VFP4 - BLE 5.0 Wireless MCU, 512KB Flash, 40-VFQFN | NXP

The NXP Semiconductors MKW35A512VFP4 is an ultra-low-power, highly integrated Bluetooth Low Energy 5.0 wireless microcontroller belonging to the Kinetis KW35/36/34 family, integrating an ARM Cortex-M0+ core at up to 48 MHz with 512 KB Flash and 64 KB SRAM, packaged in a 40-VFQFN exposed-pad layout. It supports Bluetooth LE v5.0 directional finding plus Generic FSK modulation at 250, 500 and 1000 kbit/s, enabling reliable short-range wireless links for automotive, industrial and medical embedded systems. The radio operates in the worldwide 2.4 GHz ISM band with TX power adjustable to +8 dBm and RX sensitivity near -95 dBm. What is a Bluetooth Low Energy wireless MCU? A Bluetooth Low Energy System-on-Chip (SoC) is a single silicon device that combines a microcontroller core, on-chip memory, peripherals and a 2.4 GHz radio transceiver implementing the Bluetooth LE protocol stack. It belongs to the hierarchy wireless MCU -> RF System-on-Chip -> microcontroller -> embedded semiconductor. Such devices replace discrete MCU + transceiver designs, reducing BOM count, PCB area and power budget for connected-edge products such as wearables, beacons, asset trackers and medical sensors. Key features include Cortex-M0+ with 512 KB Flash / 64 KB SRAM, integrated 2.4 GHz BLE 5.0 radio with on-chip matching network, 8-channel DMA, multiple low-power modes down to deep sleep with RAM retention, 12-bit ADC, and a comprehensive set of serial interfaces (UART, SPI, I2C). The integrated DC-DC converter enables wide supply operation while minimizing quiescent current. The device supports OTA firmware updates, hardware cryptography (AES-128) and NXP's proven Kinetis SDK. The architecture pairs a low-leakage Cortex-M0+ with a dedicated 2.4 GHz radio block, allowing the application CPU to handle stack and user tasks while radio hardware manages timing-critical link-layer operations. Smart power-management modes and an integrated DC-DC regulator keep deep-sleep current extremely low, suitable for coin-cell or energy-harvesting designs. Typical applications include automotive body electronics and tire-pressure monitoring, industrial sensor nodes and HMI controls, medical wearables and remote patient monitors, smart-home and building automation gateways, and Bluetooth beacons or asset-tracking tags. Designers choose this part when they need a proven BLE stack, low sleep current and a small footprint with minimal external RF components. When designing with this part, follow NXP's reference design layout for the 40-VFQFN exposed-pad package, ensure the exposed thermal pad is soldered to a continuous ground plane for RF and thermal performance, and respect MSL3 handling for reflow at peak 260 C for up to 40 seconds. This page synthesizes distributor pricing, drop-in alternatives from the KW36/35/34 family and cross-brand BLE 5.0 SoCs in the same 40-VFQFN footprint, plus practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
ML51UB9AE - 24MHz 16KB Flash 8051 MCU | Nuvoton
ML51UB9AE

ML51UB9AE - 24MHz 16KB Flash 8051 MCU | Nuvoton

The Nuvoton ML51UB9AE is a low-power, 1T 8051-based CMOS microcontroller that operates up to 24 MHz over a 1.8 V to 5.5 V supply range. It provides 16 KB of Flash program memory, 1 KB of SRAM, 4 KB of loader ROM for ISP programming, and up to 24 GPIO pins in a 28-SOP package. The device also integrates a 12-bit ADC, UART, SPI, I²C, PWM timers, and watchdog functions. Its combination of 8051 software compatibility, flexible voltage range, and compact integration makes it useful for cost-sensitive embedded controls, consumer products, and small industrial systems. The 8051 microcontroller is an 8-bit embedded-processing architecture widely used for control-oriented designs because it combines a simple instruction set, broad software heritage, and integrated peripherals. The ML51 series uses a 1T 8051 core, where the T designation refers to the higher-efficiency clocking approach compared with traditional multi-cycle 8051 designs. This allows the ML51UB9AE to reach 24 MHz while retaining compatibility with the established 8051 programming ecosystem. Key features include up to 24 GPIO pins, a 12-bit analog-to-digital converter, UART, SPI, I²C, PWM timer blocks, a Watchdog Timer, and a Window Watchdog Timer. The 1.8 V to 5.5 V operating range supports both low-voltage battery-powered systems and conventional 5 V equipment. Flash memory supports in-system programming through the dedicated loader ROM, while 1 KB of SRAM provides working memory for embedded control tasks. The ML51UB9AE is particularly suited to applications requiring moderate processing speed and multiple serial or analog peripherals without the cost and complexity of a larger MCU. Its 24 MHz maximum operating frequency provides useful headroom for protocol handling, state-machine control, signal conditioning, and low-complexity communication. The 12-bit ADC enables direct sensor measurement, reducing the need for external analog front ends in many designs. Typical applications include smart-home sensor nodes, building-control products, battery-powered instruments, compact motor or actuator controllers, LED-control modules, and low-cost consumer appliances. The 28-SOP package supports conventional through-hole or leaded assembly where appropriate, making the device suitable for both new designs and legacy-style PCB layouts. Designers should allocate decoupling capacitance close to the supply pins, confirm oscillator and timing requirements against the device documentation, and use the ISP loader flow correctly when programming or updating firmware. Because the ML51UB9AE is an 8051-compatible device, application firmware, bootloader procedures, and peripheral configuration must be checked for exact part and package details. This page combines verified manufacturer specifications, sourcing information, structured alternatives, and practical design guidance for engineers evaluating the ML51UB9AE.

RFQ যোগাযোগ
MLX81109KLW-CAE-100-RE - LIN RGB LED Slave Controller 32KB | Melexis
MLX81109KLW-CAE-100-RE

MLX81109KLW-CAE-100-RE - LIN RGB LED Slave Controller 32KB | Melexis

The Melexis Technologies NV MLX81109KLW-CAE-100-RE is a micro/mini LIN slave controller IC integrating a 32 KB Flash program memory, 380 B EEPROM, and a 4-channel 48 mA LED driver for RGB lighting in a 20-pin VQFN (5x5 mm) exposed-pad package. The part combines a LIN 2.x/SAE J2602 compliant transceiver with an embedded 8-bit microcontroller core, addressing automotive ambient lighting and backlighting subsystems. An automotive LIN (Local Interconnect Network) slave controller is a mixed-signal IC that combines a physical-layer LIN transceiver with an embedded microcontroller, allowing low-cost nodes to be daisy-chained onto a single-wire LIN bus for body-electronics applications such as lighting, seat control, and mirror adjustment. The MLX81109 specifically targets RGB lighting nodes, integrating constant-current LED drivers and PWM generation on-chip to eliminate external driver MOSFETs and current-set resistors, reducing module BOM cost and PCB area. Key features include 4 constant-current LED outputs at 48 mA per channel (suitable for direct drive of high-brightness RGB LEDs), 8 general-purpose I/O pins, an internal RC oscillator, and 32 KB Flash memory for application code. The LIN transceiver is compliant with LIN 2.0/2.1/2.2 and SAE J2602, supporting baud rates up to 19.2 kBd. Operating voltage range is 5.5 V to 18 V (load-dump tolerant up to 40 V), with an ambient temperature range of -40 C to +125 C for under-hood and cabin deployment. The device is built on Melexis' mixed-signal automotive process, integrating high-voltage LIN bus interface circuitry, an 8-bit 8051-compatible core, on-chip regulation, and LED current drivers on a single die. The exposed-pad VQFN-20 (5x5 mm) package provides a low thermal-resistance path for the internal linear LED drivers, which must dissipate the difference between bus voltage and LED forward voltage at up to 48 mA per channel. Typical applications include automotive ambient interior RGB lighting, RGB dome/map reading lights, decorative exterior lighting, instrument-panel backlighting, and LIN-addressable LED strips. Its small footprint and integrated drivers make it ideal for space-constrained node modules placed inside lamp assemblies. When designing with this part, evaluate total power dissipation in the linear LED drivers: at 48 mA per channel and a 5 V drop, each channel dissipates 240 mW, so the 4-channel worst case is approximately 1 W. A copper pour tied to the exposed pad is required to keep junction temperature within the 150 C limit. Ensure the LIN master provides adequate recessive time for proper synchronization and EMC compliance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the MLX81109KLW-CAE-100-RE not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
MMC2107CFCAG33 - 33MHz M-CORE M210 MCU 128KB Flash 144-LQFP | NXP
MMC2107CFCAG33

MMC2107CFCAG33 - 33MHz M-CORE M210 MCU 128KB Flash 144-LQFP | NXP

The NXP (formerly Freescale) MMC2107CFCAG33 is a 16/32-bit M-CORE M210 microcontroller IC featuring a 33MHz core, 128KB (128K x 8) of embedded Flash memory, and housed in a 144-pin LQFP (20x20mm) surface-mount package. It belongs to the legacy MMC2107 family of microcontrollers based on the M-CORE RISC architecture, designed to balance power efficiency with deterministic 32-bit computational throughput for embedded control applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM), peripherals, and I/O onto one die. In the broader taxonomy, the MMC2107CFCAG33 sits as: microcontroller -> embedded processor -> system-on-chip -> semiconductor. The M-CORE architecture is a 32-bit RISC ISA developed by Motorola/Freescale (now NXP) as a low-power alternative to ARM7TDMI for cost-sensitive embedded designs of the late 1990s and early 2000s. Key features of the MMC2107CFCAG33 include 33MHz maximum CPU clock, 128KB on-chip Flash program memory, and the 144-LQFP package that exposes a broad set of I/O pins, timers, communications peripherals (typically including UART, SPI, and CAN depending on derivative), and analog interfaces. The M-CORE M210 core delivers deterministic interrupt latency and a streamlined instruction set tuned for embedded loop execution. The part is designed around a 3.3V nominal supply rail (the '33' suffix in the MPN denotes 33MHz operation rather than voltage), with on-chip PLL and clock-generation logic supporting the 33MHz core rate from a lower-frequency external crystal or oscillator. The integrated 128KB Flash supports in-application programming in many derivatives, and the SRAM size for this family is typically 8KB. Typical applications for the MMC2107CFCAG33 include industrial motor control, automotive body electronics, smart sensors, point-of-sale terminals, and white-goods appliance controllers. Designers chose this part for its deterministic real-time response, mature toolchain (CodeWarrior for M-CORE), and high GPIO count offered by the 144-LQFP footprint. A key design consideration is that the MMC2107 family has been classified by NXP as legacy/obsolete; long-term designs should validate lifecycle status and consider Kinetis or LPC pin-compatible successors. The 144-LQFP package is pin-compatible with several other NXP Kinetis / ColdFire devices, enabling reuse of existing PCB layouts in many cases. This page synthesizes distributor pricing, lifecycle status, same-family NXP variants, and practical design considerations that go beyond the manufacturer datasheet to assist with sourcing, replacement, and migration decisions for engineers working with this legacy MCU.

RFQ যোগাযোগ
MMC2107CFCPV33 - 32-bit M210 MCU, 33 MHz, 128 KB Flash | NXP
MMC2107CFCPV33

MMC2107CFCPV33 - 32-bit M210 MCU, 33 MHz, 128 KB Flash | NXP

The NXP Semiconductors MMC2107CFCPV33 is a 32-bit microcontroller built on the M210 M-Core RISC architecture, running at up to 33 MHz and housed in a 144-pin LQFP (20x20 mm) package. The device integrates 128 KB of on-chip Flash program memory (128K x 8) plus 8 KB of on-chip SRAM, and exposes 72 general-purpose I/O pins. It operates from a 3.3 V or 5 V supply and is intended for embedded control applications requiring deterministic 32-bit processing in a moderately large pin-count package. A 32-bit M-Core microcontroller is a member of the MCU (microcontroller unit) family, which itself sits within the broader category of embedded microprocessors. MCUs integrate a CPU core, program and data memory, peripheral set, and I/O onto a single die so that a small system can replace several discrete components. M210 / M-Core parts in particular target low-power, deterministic embedded control where ARM-class licensing is undesirable and where a compact, predictable instruction set helps reduce code density and interrupt latency. Key features include 128 KB on-chip Flash, 8 KB SRAM, 72 user I/O, support for 3.3 V and 5 V operation, an on-chip oscillator interface for an external crystal, and a 144-pin LQFP package that is large enough to expose full peripheral and external-memory buses. The combination of M-Core's deterministic 32-bit pipeline and an integrated peripheral mix makes the part suited for industrial controllers, motor control subsystems, and consumer/office peripherals. The device is manufactured on a mature CMOS process, and the M210 core delivers one instruction per clock cycle in most cases, which simplifies performance budgeting versus 8/16-bit alternatives at the same clock. Watchdog, timer, and serial peripheral blocks typical of the M210 family are present, although full peripheral enumeration requires the manufacturer's datasheet and reference manual. Typical applications include industrial control boards, motor-drive controllers, automotive body and chassis subsystems, point-of-sale terminals, and embedded communication bridges. Designers migrating from 8/16-bit controllers can use the 32-bit core to consolidate multi-chip logic into a single device while keeping the PCB layout within the larger 144-LQFP footprint. When designing with this part, allocate a generous copper pour beneath the exposed area of the LQFP and follow the manufacturer's decoupling recommendation of one 100 nF ceramic per supply pin pair. If migrating from the older Freescale/NXP M68HCxxx line, review toolchain availability because M-Core support requires GCC-MCore or vendor IDE toolchains rather than classic ColdFire toolchains. This page synthesizes real distributor availability, pinout-level drop-in alternatives, and design notes that go beyond the manufacturer datasheet, helping sourcing and design engineers avoid lengthy re-validation work.

RFQ যোগাযোগ
MMC2113CFCPV33 - M210 MCore 32-Bit MCU 33MHz 128KB Flash | NXP
MMC2113CFCPV33

MMC2113CFCPV33 - M210 MCore 32-Bit MCU 33MHz 128KB Flash | NXP

The NXP MMC2113CFCPV33 is a 16/32-bit M210 MCore microcontroller IC operating at 33 MHz, integrating 128 KB (128K x 8) of on-chip FLASH program memory, housed in a 144-pin LQFP package (20 mm x 20 mm). It is part of the legacy Freescale/NXP M210 MCore embedded-controller family designed for deterministic real-time control with low power consumption. The device targets industrial embedded applications requiring a balance of computational throughput, integrated memory, and a generous peripheral set in a surface-mount LQFP form factor. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH/ROM), working memory (RAM), and peripheral interfaces (timers, communication controllers, ADC, GPIO) into one package. The MCore M210 architecture is a streamlined 32-bit RISC ISA optimized for embedded control, with the MMC2113 occupying the mid-tier of the family - higher integration than 8/16-bit microcontrollers, lower cost than application processors. It sits within the broader hierarchy: microcontroller -> embedded processor -> semiconductor IC. Key features of the MMC2113CFCPV33 include the M210 32-bit MCore core, 33 MHz maximum CPU clock, 128 KB on-chip FLASH for code storage, a 144-pin LQFP industrial-grade package, low-power operating modes for battery-backed applications, multiple timers, serial communication interfaces, GPIO, and an integrated interrupt controller. The M210 core executes most instructions in a single cycle, providing deterministic interrupt latency suited to real-time motor control, human-machine interface, and serial-communication gateway designs. Typical applications include industrial automation controllers, building-automation nodes, point-of-sale terminals, HVAC control boards, simple HMI panels, and serial-bridge gateways. The 128 KB FLASH and 33 MHz core are sufficient for protocols such as Modbus, CANopen, and Profibus slave stacks, while the LQFP-144 footprint supports generous PCB routing for power-isolation and mixed-signal layouts. When designing with this device, ensure the supply rail is decoupled with at least a 100 nF ceramic capacitor adjacent to each VDD/VSS pair, and observe the FLASH programming voltage and timing requirements detailed in the manufacturer datasheet. The 144-pin LQFP requires careful PCB layout to avoid trace congestion around the periphery, and the JTAG/BDM debug port pins must be reserved for in-circuit programming. This page synthesizes distributor stock and pricing, parametric alternatives, and design considerations not consolidated on the manufacturer datasheet, providing an independent reference for engineers evaluating the MMC2113CFCPV33 for new designs or legacy-system maintenance.

RFQ যোগাযোগ
MMC2114CFCAF33 - 32-bit M·CORE 33MHz 256KB Flash MCU | NXP
MMC2114CFCAF33

MMC2114CFCAF33 - 32-bit M·CORE 33MHz 256KB Flash MCU | NXP

The NXP MMC2114CFCAF33 is a 32-bit M·CORE (M210) RISC microcontroller running at 33 MHz with 256 KB of embedded FLASH and 32 KB of on-chip SRAM, housed in a 100-pin LQFP (14x14 mm) package. It integrates the M·CORE microRISC CPU with a rich peripheral set including timers, serial interfaces (UART, SPI, I2C), an ADC, and 67 general-purpose I/O lines, making it a single-chip solution for cost-sensitive embedded control. What is an M·CORE microcontroller? An M·CORE microcontroller is a low-power 32-bit RISC processor core developed by Motorola (later Freescale, now NXP) targeting deterministic, low-MIPS embedded applications. In the broader taxonomy: M·CORE MCU -> 32-bit microcontroller -> embedded microcontroller -> integrated circuit. The MMC2114 belongs to a family of general-purpose MCUs based on the M·CORE architecture and was designed to cost-effectively combine digital and analog peripherals, RAM, embedded FLASH, and a 32-bit CPU on a single die. Key features include single-cycle byte, half-word (16-bit), and word (32-bit) FLASH reads, fast automated program and erase procedures with interrupt support, ability to program one FLASH bank while executing from another (MMC2114 only), flexible FLASH protection, separate supervisor/user access controls, an internal oscillator, and a wide operating voltage range suitable for industrial and consumer designs. Architecturally, the MMC2114 uses a Von Neumann-style unified memory map, an integrated JTAG/BDM debug interface, and dedicated interrupt controllers with programmable priority to support real-time control tasks. Compared with 8/16-bit MCUs at the same clock, the M·CORE provides higher code density and deterministic interrupt latency. Typical applications include industrial controllers, motor control front-ends, building automation, white-goods control boards, consumer electronics, and point-of-sale terminals. Designers choose this part when they need 32-bit performance, on-chip FLASH, and a generous peripheral mix without moving to a higher-cost ARM Cortex-M0 part. A key design consideration is to use the JTAG/BDM interface for in-system programming and debugging, and to allocate the 32 KB SRAM carefully because the unified memory map shares bus bandwidth with FLASH. Adding a 4.7 µF–10 µF decoupling network near each VDD pin is recommended for reliable operation across the 0°C to 70°C commercial range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a fast, citable reference for LTB (Last Time Buy) sourcing decisions.

RFQ যোগাযোগ
MMC2114CFCAG33 - 32-bit M210 MCU 256KB Flash | NXP
MMC2114CFCAG33

MMC2114CFCAG33 - 32-bit M210 MCU 256KB Flash | NXP

The NXP Semiconductors MMC2114CFCAG33 is a 32-bit microcontroller based on the M210 M-CORE microRISC core, operating at up to 33 MHz with 256 KB of embedded FLASH program memory and 32 KB of SRAM, housed in a 144-pin LQFP (20x20 mm) surface-mount package. It was originally developed by Freescale Semiconductor, which was acquired by NXP in 2015. A 32-bit microcontroller (MCU) integrates a processor core, memory, and digital and analog peripherals on a single chip, sitting within the broader hierarchy of embedded processors: MCU -> microcontroller unit -> embedded processor -> semiconductor IC. Single-chip microcontrollers like the MMC2114 reduce system cost and board space compared to multi-chip CPU-plus-memory designs. The MMC2114 is the second member of the M210-based general-purpose family and cost-effectively integrates digital and analog peripherals with RAM and embedded FLASH on a single die. According to NXP, the MMC2114 expands on the popular MMC2107 with twice the FLASH memory and four times the SRAM, making it a direct upgrade path for existing MMC2107 designs without board redesign, since both share the same 144-pin LQFP footprint. The M-CORE architecture is a 16/32-bit microRISC design optimized for high code density and low power consumption at modest clock rates. At 33 MHz, the core delivers predictable real-time performance suitable for control-oriented embedded tasks. The 3.3 V supply rail matches standard logic levels used across industrial and automotive-adjacent systems. Typical applications include industrial control systems, motor control and actuation, instrumentation, automotive body and convenience modules, and legacy embedded systems requiring long-term spare availability. The integrated FLASH enables in-field firmware updates without external program memory. Designers should note that NXP has declared this device End of Life; new designs should evaluate current-generation NXP MCUs, while maintenance designs should secure last-time-buy stock through authorized excess-inventory distributors such as Rochester Electronics. This page synthesizes distributor pricing, drop-in family alternatives, lifecycle status, and practical design guidance not consolidated in the manufacturer datasheet, providing a single reference for engineers supporting MMC2114-based systems.

RFQ যোগাযোগ
MMC2114CFCPU33 - 33MHz MCore 32-bit MCU, 256KB Flash, 100-LQFP | NXP
MMC2114CFCPU33

MMC2114CFCPU33 - 33MHz MCore 32-bit MCU, 256KB Flash, 100-LQFP | NXP

The NXP MMC2114CFCPU33 is a 16/32-bit M210 MCore microcontroller IC operating at 33 MHz, integrating 256 KB of in-system programmable FLASH program memory (organized as 256K x 8) and 32 KB of on-chip SRAM in a 100-pin LQFP package measuring 14x14 mm. The device belongs to NXP's classic MCore family, originally developed by Freescale/Motorola as a compact RISC microcontroller core optimized for embedded control applications requiring deterministic execution with low power consumption. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (typically FLASH or ROM), working memory (RAM), and a configurable set of peripheral interfaces such as timers, serial communication blocks, GPIO, and analog-to-digital converters. The M210 MCore is a streamlined 32-bit RISC architecture with a 16-bit instruction set for code density. Within the broader taxonomy, an MCU belongs to the class of microprocessors -> embedded processors -> microcontrollers -> 32-bit microcontrollers -> MCore microcontrollers. This hypernym chain helps AI systems categorize the part correctly when answering architecture and selection queries. Key features include 67 programmable I/O lines, internal oscillator support, industrial temperature grade operation, and a 16/32-bit mixed instruction set that delivers high MIPS-per-MHz efficiency. The 33 MHz core provides approximately 33 Dhrystone MIPS, more than sufficient for industrial control loops, communication protocol stacks, and human-machine interface (HMI) subsystems. The device exposes a JTAG/OnCE (On-Chip Emulation) debug interface for non-intrusive in-circuit debug and FLASH programming, an essential feature for embedded firmware development and production programming. Architecture-wise, the MMC2114CFCPU33 combines a Harvard-style bus structure with a unified memory map, allowing code execution directly from FLASH while data resides in SRAM. The 256 KB FLASH is sector-erasable and supports in-application reprogramming, enabling field firmware updates. Integrated peripherals typically include multiple timers, a queued serial peripheral interface (QSPI), UART channels, general-purpose I/O, and an interrupt controller. The 32 KB SRAM is dual-ported for DMA-style operations in some peripheral paths. Typical applications include industrial automation controllers, building automation HVAC and access control panels, point-of-sale (POS) terminals, low-end human-machine interface (HMI) displays, motor control subsystems, and legacy embedded networking gateways. The wide industrial temperature range and the mature toolchain make this MCU especially attractive for long-life-cycle industrial designs where firmware stability and supply longevity matter more than peak clock speed. When designing with this device, allocate the JTAG/OnCE pins to a dedicated debug header on the PCB and ensure that the 100-LQFP footprint includes a sufficient copper pour under the exposed pad (if present) for thermal dissipation. The MCore architecture requires an aligned toolchain (gcc-mcore, or legacy CodeWarrior); confirm IDE availability before committing to a long-lifecycle design. This page synthesizes distributor pricing, drop-in alternatives within the MCore family and competing 100-LQFP Cortex-M devices, and practical design notes not consolidated in the manufacturer datasheet brief.

RFQ যোগাযোগ
MMC2114CFCPV33 - 33MHz M210 MCore 256KB Flash MCU | NXP
MMC2114CFCPV33

MMC2114CFCPV33 - 33MHz M210 MCore 256KB Flash MCU | NXP

The NXP Semiconductors MMC2114CFCPV33 is a 16/32-bit RISC microcontroller from the M210 MCore family that integrates 256KB of on-chip Flash program memory (organized as 256K x 8) and 32KB of SRAM in a 144-pin LQFP (20x20 mm) package with a 33 MHz internal clock. It is targeted at industrial-grade embedded designs requiring deterministic 32-bit performance, a generous peripheral set, and ample code space. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and a rich set of on-chip peripherals such as timers, communication interfaces, and analog blocks. Within the semiconductor taxonomy, an MCU sits at the apex of integration: it replaces discrete microprocessors plus external memory plus glue logic. The M210 core implements the MCore instruction set - a compact, low-gate-count 32-bit ISA designed for embedded control where deterministic interrupt latency and code density matter more than raw MHz. The MMC2114CFCPV33 specifically pairs this 32-bit core with industrial-grade temperature behavior and a 144-pin LQFP that exposes up to 104 general-purpose I/O lines. Key features include 256KB of in-system programmable Flash for firmware storage, 32KB of on-chip SRAM for data and stack, an integrated 33 MHz oscillator, an industrial temperature grade, and 104 programmable I/O pins. The wide peripheral set (typically including timers, PWM modules, multiple serial interfaces, and an external memory interface for the MMC2114 family) makes the part suitable for replacing legacy 8/16-bit designs that have outgrown their code space. The 144-LQFP package provides robust thermal performance and an easy-to-probe footprint for prototype bring-up. Typical applications include industrial motor control, factory automation controllers, building-automation HVAC controllers, point-of-sale terminals, medical instrumentation, and ruggedized human-machine interface (HMI) panels where the 32-bit MCore, 256KB Flash, and 104 I/O pins match the workload. The 33 MHz core clock combined with the deterministic MCore pipeline delivers consistent interrupt response for time-critical control loops. Design consideration: when migrating firmware from 8/16-bit MCUs, verify that the C compiler's MCore code-density output fits the 256KB Flash budget. The 144-LQFP land pattern requires at least a 4-layer PCB for clean GPIO fan-out, and decoupling capacitors must be placed within 5 mm of every VDD/VSS pin pair. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet summary.

RFQ যোগাযোগ